Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | Item Rate BoQ 82560/E8 BoQ_Ver3.0 Item Rate Normal INR Only INR Select, Excess (+), Less (-) Less (-) Tender Inviting Authority: CWE JAIPUR Name of Work: SPECIAL REPAIR OF ECHS POLYCLINIC AT JHUNJHUNU UNDER GE (S) JAIPUR CA NO: CWE/JPR(S)- OF 2026-27 Bidder Name : PRICE SCHEDULE(This BOQ template must not be modified/replaced by the bidder and the same should be uploaded after filling the relevent columns, else the bidder is liable to be rejected for this tender. Bidders are allowed to enter the Bidder Name and Values only ) NUMBER # TEXT # TEXT # NUMBER # TEXT # NUMBER NUMBER TEXT TEXT # NUMBER # TEXT# TEXT # NUMBER # NUMBER NUMBER NUMBER NUMBER TEXT TEXT NUMBER NUMBER NUMBER NUMBER TEXT TEXT NUMBER NUMBER NUMBER NUMBER TEXT TEXT NUMBER NUMBER NUMBER NUMBER TEXT TEXT NUMBER NUMBER NUMBER NUMBER TEXT TEXT NUMBER NUMBER NUMBER # NUMBER # TEXT TEXT NUMBER # NUMBER # DATE NUMBER # NUMBER # TEXT # NUMBER # SNo Item Description Item Code / Make Qty Units Estimated Rate Addition / Deduction Addition / Deduction Values Currency Convertion against each Item Quoted Currency in INR / Other Currency Rate in Figure Excise Duty VAT Freight Charges ( Unloading & Stacking) Any Other Taxes/Duties/Levies Other Taxes 2 IIIrd Party i.e DGS&D / RITES etc Inspection Charges @0.34%+Service Tax Less for Cenvat Credit,if any respect of Supplies Under full Excise Duty Category TOTAL AMOUNT Without Taxes TOTAL AMOUNT With Taxes Rate in Words Total Amount |
| 2 | Taking down cement plaster any description, on brick or stone walls, etc. including raking out joints, hacking for key & scrubbing down with water, etc. & removing rubbish outside MoD land etc complete all as specified and directed. |
| 3 | M&L rendering 15 mm thick on fair faces of brick work or concrete surfaces in CM 1:4 finished even and smooth without using extra cement etc complete all as specified and directed. |
| 4 | M&L for Rough cast plaster including 15mm thick rendering in CM (1:3) on brick work or concrete surfaces complete as specified in SSR pat -I clause 14.22 etc complete all as specified and directed. |
| 5 | M&L rendering 15 mm thick on fair faces of brick work or concrete surfaces in CM 1:6 finished even and smooth without using extra cement etc complete all as specified and directed. |
| 6 | M&L rendering 05 mm thick on fair faces of brick work or concrete surfaces in CM 1:3 finished even and smooth without using extra cement etc complete all as specified and directed. |
| 7 | M&L for preparation of newly plastered surfaces / rough cast plaster of wall and applying two coats of exterior emulsion paint by mechanical means over a coat of primer including 1 mm of cement base wall care putty etc complete all as specified and directed. |
| 8 | M&L for preparation of newly plastered surfaces of wall and applying two coats of plastic emulsion paint by mechanical means over a coat of primer including 1 mm of thick wall care putty complete all as specified and directed. |
| 9 | M&L for preparation of newly plastered surfaces of ceiling and applying two coats of plastic emulsion paint by mechanical means over a coat of primer including 1 mm of thick wall care putty complete all as specified and directed. |
| 10 | M/L Complete removal of existing treatment of old plastered wall surfaces and Washing, rubbing down and stopping of painted surfaces and applying two coats of exterior emulsion paint by mechanical means over including 1 mm of cement base wall care putty complete upto two/three storey building including scaffloding arrangement all as specified and directed by Engineer-in-Charge. |
| 11 | M&L for complete removal of existing treatment and applying two coat of plastic emulsion paint over a coat of primer including 1 mm of wall care putty by mechanical means on plaster surface/concrete surface etc complete all as specified and directed. |
| 12 | M & L Complete removal of existing treatment of old plastered surfaces of ceilling and Washing, rubbing down and stopping of painted surfaces & applying two coats of plastic emulsion paint by mechanical means etc complete all as specified and directed. |
| 13 | Cutting openings, through brick walls built in cement mortar, for door, windows and other openings or enlarging existing openings, converting window into door openings, etc. including providing, fixing and removing shoring, cleaning stacking bricks, removing surplus serviceable bricks,hard core, etc. to store and rubbish off the premises not exc.50 mtr. complete all as specified and directed . |
| 14 | Demolition of brickwork or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc but excluding ashlar facings, dressed stonework and precast concrete but excluding ashlar facings, dressed stonework and precast concrete articles etc complete all as specified and directed. |
| 15 | M&L for brick work with subclass 'B' bricks, straight or curved on plan exc 6 m mean radius built in cement mortar 1:4 |
| 16 | M&L Brickwork with sub-class ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:6 |
| 17 | Dismantling of floor, hearth or wall tiling or stone slab laid, bedded & pointed in any mortar including demolition of cement mortar bedding or backing coat, including removal of debries to a distance exc 1.5 km but n.exc 2 Km in low laying area etc complete all as specified and directed. |
| 18 | M & L 25mm thick cement concrete type B-0,1:2:4 , 12.5mm graded aggregate and finishing cement concrete surface even and smooth with using extra cement. |
| 19 | M&L for light shade Vitrified Ceramic tiles 8-10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and jointed in neat cement slurry & jointed in coloured cement to match the colour of tiles over complete including 15mm thick screed bed in cm 1:6 / or by adhesive all as specified and directed all as specified and directed. |
| 20 | All as per above Ser No 17.00 but as in skirting/ vertical surface over & including 10mm thick rendering on stone/brick masonary surface or PCC engrs board surface in CM 1:4 etc complete all as specified and directed. |
| 21 | M & L for Glazed digital printed ceramic coloured tiles in vertical surface 350 x 250 x 7mm / 450 x 300 x 7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over & including 10mm thick rendering on stone masonary surface or surface other than fair faces of brick work in CM 1:4 etc complete all as specified and directed. |
| 22 | M&L for Non - skid coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over complete including 15mm thick screed bed in cm 1:6 / or by adhesive all as specified and directed all as specified and directed. |
| 23 | M&L for Non - skid coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over complete including 15mm thick screed bed in cm 1:6 / or by adhesive all as specified and directed all as specified and directed. |
| 24 | M/L Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete over 20 mm thick cement screed bed in CM 1:4. |
| 25 | M/L Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over 10 mm thick cement plaster 1:4 complete all as specified and directed. |
| 26 | M & L of 20 mm thick Granite (of any type) work (table rubbed and polished) in Slab,steps, jambs, pillars, window cills and all horizontal portion and like in 15 mm thick cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite. |
| 27 | M & L 20 mm thick Granite (of any type) work (table rubbed and polished) for wall (veneering to wall) and any vertical surface etc with 12mm thick cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite. |
| 28 | Dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets |
| 29 | Providing & fixing pvc false ceiling 12 mm thick micro tegular edged or 10 mm thick square edged false ceiling tiles of size 595x595 mm of approved texture design and patterns having moisture content less than 2% humidity resistance of 99% NRCO 0.50 to 0.75 as per IS 8225:1987 Noncombustible as per BS 476 (part 4)- 1970 and light reflection of 85% (minimum) to be laid in true horizontal level suspended on interlocking metal T grid of hot dipped galvanized iron section of 0.33 mm thick (galvanized @ 120 grams per sqm including both sides) comprising of maint T runners of size 15x32 mm of length 3000 mm cross T of size 15x32 mm of length 600 mm to form grid module of size 600x600 mm, suspended from celing using galvanized mild steel items (galvanizing @ 80 grams per sqm) i.e 50 mm long 8 mm outer diameter M- 6 dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L- shape level adjuster of size 85x25x2 mm Galvanised iron perimeter wall angle of size 24x24x 0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm centre to centre and 40 mm long dry wall wood screws. the work shall be carried out as per specifications, drawing and as per directions of the Engineer-in-Charge. |
| 30 | Demolition of cement concrete reinforced in ground floor and paving n exc 15 cm thick (below or above ground level) complete all as specified and as directed.Note: Old Unserviceable TMT obtained from this item shall be deposited in store & taken on charge by EIC. |
| 31 | M&L for Precast cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate as in landings, cover slab (for manholes etc),chullah hoods, chajjas, water troughs,mangers, shelves and similar work including necessary form work and set in CM 1:6 complete all as specified and as directed. |
| 32 | M&L Mild Steel TMT bar 10 mm dia and over cut to length bent to shape required including cranking, bending spirally for hoping for columns hooking ends and binding with & including Mild Steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed. |
| 33 | M & L for RCC 1:2:4 type B1 using 12.5mm graded aggregate in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed by the Engineer-in-Charge.Note :- Reinforcement shall be measured and paid separately |
| 34 | M & L for flat formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping), work in rough finished flat surfaces of concrete complete all as specified and as directed by the Engineer-in-Charge |
| 35 | Taking down of Aluminium door/window shutter of any description area of each shutter not exceeding 1.5 sqm and refixing in same opening after carry out necessary repair including change of hinges, neoprene rubber beading, oiling, tightening the joints/bolts/tightening all loose screw , hinges, rubber beading, aluminum beading, handles, sliding bolts, hings, tower bolts etc including repairing the damage portion of chowkhat or frame complete all as specified and directed.NOTE: (i) Floor spring to be paid under relevent Item of this schedule.ii) Rate should incl all T&P required for repair incl fixing of rubber packings, screws etc complete to make good the shutter all as directed. |
| 36 | All as per item No 34.00 here-in-before but area exceeding 1.5 sqm and n exc 4.00 sqm each shutter |
| 37 | Taking down chowkats or frames not exceeding 1.5 Sqm each with shutter (without taking off shutter from the frame) and removing from site complete all as specified and directed. |
| 38 | Taking down chowkats or frames exceeding 1.5 Sqm but not exceeding 4 Sqm each with shutter (without taking off shutter from the frame) and removing from site complete all as specified and directed. |
| 39 | Supply fabricate & fix in position anodised aluminium powder coated (minimum thickness of powder coating 50 micron of approved colure) door shutter with frame, partly glazed with 5 mm thick tinted glass and partly panelled with 9 mm thick prelaminated particle board with both side decorative laminated including rubber bead joining cleat for fixing in position, aluminium door handle 150 mm size, aluminium barrel tower bolt 200 mm size etc all as specified below complete all as specified and directed. (a) Frame (top & side) section shall of size 101.60 x 44.75 x 2.4 mm ( Section No 14021)(b) Vertical Members of shutter Section shall be of size 85.00 x 44.45 x 2.00 mm (Section No 19560)(c) Top Members of shutter Section shall be of size 83.50 x 44.45 x 2.00 mm (Section No 19581)(d) Lock rail (Middle member) of shutter Section shall be of size 150.00 x 44.45 x 3.00 mm (Section No 19596)(e) Bottom Members of shutter Section shall be of size 150.00 x 44.45 x 3.10 mm (Section No 19584) (f) Glazing clip for securing glass of shutters shall be of 0.80 mm thick (Section No 19370).Note:-(i) Section No given above are of make Jindal, contractor may use similar section of Make Hindalco / Nalco (ii) Floor door spring & lock will be measured & paid separately. |
| 40 | M&L for Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed in repairs. |
| 41 | S&F mild steel body mortice lock 4 levers vertical type complete all as specified fixed in repairs. |
| 42 | S&F for 4.8 mm thick sheet glass odinary qulity and glazing with neosprene beading n.exc 0.5 Sqm in each pane |
| 43 | S & F for solid PVC door frame of size 50x47mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, supplied and fixing in opening as specified and shown on drawing made on section 8 of SSR 2010 Part-II complete all as specified and directed. |
| 44 | S&F Factory made solid PVC Moulded door shutter, 28 to 30 mm thick (stiles) with 2, 4, or 6 raised panel design with 2 mm thick moulded prelam PVC sheet on the front face and 2 mm prelam PVC sheet on back face,with particle board core supplying and fixing in the frame as shown on drawing in section 8 of SSR-2010 Part-II complete all as specified and directed |
| 45 | S&F aluminium, anodised, barrel tower bolts of extruded section 200 mm long complete all as specified and directed. |
| 46 | S&F Butt hinges, medium weight, cold rolled mild steel 100 mm long complete all as specified and directed. |
| 47 | S&F extruded aluminium alloy handles fabricated type anodised of 150 mm size complete all as specified and directed. |
| 48 | S&F aluminium power coated partition wall fixed type made out of aluminium anodized standard hollow section 100x40x1.60mm thick snap frame work including 5.5mm thick glass or 12mm thick prelaminated particle board , interior grade prelaminated one side with decorative choice lamination & other side balancing light grey laminationetc fixed with glazing clips rubber beading /gasket anodized aluminium beading screws etc complete all as specified and directed by Engr-in-Chagre |
| 49 | S&F Anodised aluminium powder coated frame of approved colour for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc glazing clips, stainless steel screws, complete all as specified |
| 50 | S&F Anodised aluminium Powder coated (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket |
| 51 | S&F in repair 25 mm dia SS drapery rod grade 304 medium weight all as specified and as directed. |
| 52 | S&F SS -304 grade brackets/ end brackets for holding drapery rod with good quality SS finials for drapery rod 25 mm dia all as specified and as directed. (Note: one pair of brackets and one pair of finials are considered as one pair in given quantity no separate amount will be paid for the same.) |
| 53 | Taking down GI tubing 15mm dia, with connections. |
| 54 | Taking down GI tubing 20mm dia, with connections. |
| 55 | Supply & Fixing for steel water tubing, galvanised, medium grade, with all fittings and fixed complete to walls & ceiling or laid in floors or concealed in walls etc of size of tubing 15 mm bore complete all as specified. |
| 56 | All as per above, but size of tubing 20 mm bore and ----ditto----- |
| 57 | S&F in repair bib taps 15mm bore cast coper alloy CP fancy type, with crutch or butterfly handle, screwed down, screwed for iron pipe or for union complete all as specified and directed. (Make : Jaquar Cat Part No ARI-CHR-39037) |
| 58 | S&F in repair two way angle valve 15mm bore cast coper alloy CP fancy type, with crutch or butterfly handle, screwed down, screwed for iron pipe or for union complete all as specified and directed. (Make : Cera Cat Part No F2002211) |
| 59 | S & F in repair 15 mm dia Angle valve, cast copper alloy chromium plated , screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions & fixed. Jaquar Cat Part No : OPP-CHR-15053PM) or equivalent in approved make. |
| 60 | S&F in repair Single Piece-WC with soft close seat cover, Hinges, Fixing Accessories, Accessories Set and Cistern fittings, including P/S trap all as specified and directed. Make :- Jaquar CAT Part No. CNS-WHT-855S220SPPSM or equivalent approved make. |
| 61 | S&F brass CP health faucet with 1.2m chain Make : Jaquar Cat Part No : ALD-CHR-587) |
| 62 | S&F brass CP toilet paper holder with flap Jaquar Cat Part No : CPA-CHR-1151) |
| 63 | Supply and fix in repair white vitreous basin of size 435 mm x 700 mm x 135 mm with pedestal fixed in position as per manufacturer instruction and connecting to drain pipe complete all as specified. |
| 64 | Supply and fix in repair brass chromium plated single lever basin mixer fixed in position as per manufacturer instruction and connecting to drain pipe complete all as specified.Make: cera Cat No F2012452 or equivalent in approved make. |
| 65 | S&F in repair Soap dish Holder including fixing to wall complete all as specified. |
| 66 | S&F in repair glass shelf 600 mm long including SS brackets complete |
| 67 | S&F in repair stainless single towel rail 600 mm long complete all as specified.Make: Jaquar Cat No AQN-7711 or equivalent in approved make. |
| 68 | S & F in repairs,5.5 to 6mm thick bevelled edge mirror of selected quality glass of size n less than 0.5 Sqm, mounted on 6mm thick AC building board or commercial plywood with decorative wooden or PVC beading all around and fixed to wooden plugs with chromium plated brass screws and cup washers all as specified and directed. |
| 69 | S&F in repair Urinal, Size: 355x340x535mm vitreous china bowl white colour with grating in and union for discharge pipe incl providing and fixing plug bedding urinal against wall in CM 1:2 securing urinal to plugs incl 60mm long brass screws and providing and fixing suitable urinal spreader and pointing around urinal back in cement complete all as specified.(Make: Jaguar, cat part - URS-WHT-13261) |
| 70 | S&F in repair brass chromium plated Urinal valve auto closing system with built in control cock & wall flange complete all as specified.Make: Jaquar Cat No PRS-077 or equivalent of make mention Appx B |
| 71 | S & F in repair Curved shaped urinal partition of granite of thikness 16mm to 20 mm thick Finished of size 950 mm and width 450 mm. |
| 72 | Demolition of old existing unserviceable EWC seat and S&F vitreous china wash down water closet pan ( Pedestal pattern ),white including connection to drain (or outgoing pipe) and to flushing pipe,anti-sypohonage pipe etc. & with plastic WC seat cover white closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device complete including flusing cistern and flush pipe |
| 73 | S & F 10 ltr capacity PVC valveless, syphonic action type, flushing cistern, low level, shite, with inlet, ball valve, float and handle including brackets. |
| 74 | Supply and fix in repair 1000 litres capacity triple layer, white coloured rotational molded, polythene water storage tank (Cylindrical vertical with closed top) hoisted and fixed on roof in position, including all fitting such as connection pieces with GI tank nipple for inlet, outlet, washout and overflow etc and including 25 mm size Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe complete. |
| 75 | S & F in repair 20 mm fancy type stop valves, chromium plated cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete |
| 76 | S & F in repair PVC connections 15mm size with PTMT nuts of length 450mm. |
| 77 | S&F in repair 75 mm dia PVC multi floor nahani trap all as per directed ISI Marked. |
| 78 | S&F in repairs Push Button liquid soap containers with /PTMT/ ABS body of capacity 0.80 ltr fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 105gms)complete all as specified and directed by Engineer-in-Charge. |
| 79 | Demolition and breaking up drain pipe (salt glazed ware, AC or reinforced concrete ) set in cement mortor for 200 mm internal dia of pipe complete all as specified and as directed. |
| 80 | M&L for cement concrete bed to drain pipes for 200 mm bore of pipe with cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate complete all as specified and as directed. |
| 81 | Dismantling of 100/75 mm dia cast iron / PVC Pipe or reinforced concrtee drain pipes, jointed in cement mortar and taking out of trenches, if required |
| 82 | S&F PVC (SWR) pipes single socketed in any length of bore 110mm with rubber ring joints fixed to wall all as specified and directed by Engr-in-charge. |
| 83 | S & F in repair PVC (SWR) bends 110 mm dia |
| 84 | S & F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trencehs ( Joining to be done with solvent cement ) including PVC brackets. |
| 85 | S & F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, laid in trenches or in floor ( Joining to be done with solvent cement ) including PVC brackets. |
| 86 | S & F in repair for 75 mm dia PVC (SWR) bends any radius |
| 87 | M&L for providing circular,raised platform of hight 20 cm below the tank and base dia 25 cm more than the external dia of tank for pvc cylendrical tank of capicity 500/1000 liters using pcc 1:3:6 type C1 using 20 mm graded stone aggregate with smooth finish including necessary form work etc. |
| 88 | Demolition of PCC in roof covering, kerbs, roof kerbs, benching, coved fillets etc including old decayed water proofing treatment of any type all as directed by Engineer-in-charge. |
| 89 | M&L for surface preparation by removal of all loose particle to ensure clean, smooth and dry surface and laying 25mm thick PCC type B-0, (1:2:4) using 12.5mm graded stone aggregate finished even & smooth without using extra cement to cover negative slope into prop with WPC @ 3% weight of cement. Note:- PCC shall be done by RMC only as per instructions of Engineer-in-Charge. |
| 90 | M&L for 15 mm thick screed bed in CM 1:4 over roof for recieving roof treatment with WPC @ 3% weight of cement mixed with recron fibres all as specified and directed. |
| 91 | M&L for carrying out water Roof treatment as under:1. All visible cracks to be opened up in V shape and remove all loose particles, cleaned properly with wire brushes and cracks are to be filled with crack filling compound for cracks upto 5 mm width/depth of cracks.2. Cracks more than 5 mm width/depth are to be filled with cement grouting like(URP cement grout) by injecting through nozzles till refusal by authorized applicators of manufacturers carefully by following manufacturer's instructions. The size and spacing if the nozzles shall be as per manufacturer's instructions/as directed by Engineer-in-charge.3. After drying, roof coat paint shall be applied (@ rate of 1 L per 1sqm) with roller in both directions with a gap of 12 hrs for each direction over a self primer coat @ 0.5 ltrs of water mixed to 1 L of roof coat paint.4. Necessary guarantee of 05 years shall be submitted by the contractor .Make:- Roof coat :- Choksey chemicals (Roof coat-3) I, Berger (HS Damp Shield Elasto)/ Asian (Smart care Damp Proof).Cement grout :- Dr. Fixit (Fixit Pidicrete URP Model:301)/or equivalent in FOSROC/Choksey Chemicals/SIKA/Berger(HS Super Grout).\\" complete all as specified and directed. |
| 92 | Dismantling wrought iron or mild steel work of any description not otherwise provided for |
| 93 | Dismantling Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings |
| 94 | S & F Steel work in tubular trusses of required shape and size including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St.-240 fixing/supported on wall |
| 95 | S & F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified |
| 96 | S & F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified |
| 97 | Preparation of new or previously untreated steel surface of any description, not otherwise described over 10cm width or girth and applying two coat of synthetic enamel paint over one coat red oxide complete. |
| 98 | M&L for preparation of old steel surfaces over 10cm width or girth of any description exc 10 cm width or girth and applying one coats of synthetic enamel paint complete all as specified and as directed.Note: (i) Rate also includes for works to carry out on secuirty wall upto height 4.50 mtr |
| 99 | Demolition of cement concrete un reinforced in ground floor and paving n exc 15 cm thick (below or above ground level) complete all as specified and as directed. |
| 100 | M&L for PCC 1:4:8 type D2 using 40mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and as directed. |
| 101 | M&L for PCC 1:3:6 type C2 using 40 mm graded stone aggregate, 75 mm thick in plinth protection laid in panels and finished even and fair including necessary form work complete all as specified and as directed. Note : Joints 12mm wide to the full depth of PCC shall be provided at every 3 meters and at every change of direction and shall be filled with mixture of bitumen and sand 1:3 by weight. Cost of this provision shall be deemed to be included in quoted rate for concrete in plinth protection. |
| 102 | M&L cement concrete in foundation type C 2, 1:3:6 ( 40 mm graded stone aggregate) as in mass concrete for sub base / path / flooring etc complete all as specified and as directed. |
| 103 | Dismantling of stone slabs and tiles of any description or thickness, laid dry or laid dry and pointed in any mortor in floor, apron etc complete all as specified and as directed |
| 104 | Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and as directed. |
| 105 | M&L for chequered cement concrete decorative designed tiles 25 mm thick of size 30cm x 30 cm x 25mm thick or as approved set, jointed and pointed in neat cement slurry with grey pigment cement and pigments in floor including 20 mm thick screed bed/bedding layer of mortar in 1:6 including dismantling old unserviceable louver and jallies frame complete all as specfied and as directed. |
| 106 | S&F posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, wind ties, etc.; flat iron fillets ( for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe 290 Gde E-165 complete all as directed. |
| 107 | S&F in repairs galvanised 2 strand , steel barbed wire 2.24 mm dia barbed with 2mm dia barbs at 15 mm soacing and straining and fixing to any type of standard rails straining bolts, including , securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc as directed (each line wire to be measured ) complete all as specified, |
| 108 | Repair only of MS rolling shutters, of any size, any description, in any position, by easening with greasing, repair/replacing of rollers, welding if required, replacing of accessories as required, including taking down and refixing in same opening complete all as specified and directed. Note :- work will be carried out in restricted as required and the cost of spare parts deemed to be included in quoted ratesii) Rate should incl all as T&P required for repair to make good the shutter all as directed. |
| 109 | S&F lead door for X room with following specifications :-(a) Door Frame : Aluminium door fame with casing and inner casing made of aluminium profile with round edges and a 15u natural powder caoted finish, inclding insertion of lead sheet for radiation protection and siliconeperimeter seald in the back of the rabbet complete all as specified as per manufractor direction.(b) Door Leaf : Door leaf shall be made HPL laminate with antibacterial surface of powder coated aluminium sheet, protected by a aluminium frame with rounded edges including lead shielding 2 to 4 mm thick, consisting of a lead sheet placed in the core of the door lead with a port hole /vision panel flush on both side for optimum cleaning complete all as specified as per manufractor direction.(c) Harware : With following hardware S.S BB Hinges-03 Nos, Mortice dead lock-01 No, door handle-02 Nos, door closer-01 No , Flush bol - 02 ost, Perimeter seal, Vision lite-01 No and Mortice sah lock & Lever Handle - 01 No |
| 110 | S&F lead window for X room with following specifications :-(a) Window Frame : Aluminium window fame with casing and inner casing made of aluminium profile with round edges and a 15u natural powder caoted finish, inclding insertion of lead sheet for radiation protection and siliconeperimeter seald in the back of the rabbet complete all as specified as per manufractor direction.(b) Window Leaf : Window leaf shall be made 8mm thick hight quality lead glass, radiation shielding equivalent to 2mm lead with providing excellent visual carity for monitoring procedures, protected by a aluminium frame complete all as specified as per manufractor direction.(c) Harware : With following hardware S.S BB Hinges-03 Nos, window handle-02 Nos, Perimeter seal, Vision lite-01 No and Mortice sah lock & Lever Handle - 01 No |
| 111 | Taking down copper / aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc. complete all as specified and directed. |
| 112 | M&L for point wiring complete with 1.5 Sqmm single core (Phase - Red, Neutral - Black) PVC insulated and unsheathed multi stranded copper conductor FRLS cable of 1100 V grade PVC insulated and unsheathed cable inclosed in and including concealed PVC conduit 20 mm dia medium grade with all accessories ISI marked, including MS sunken box / modular metal flush box of thickness not less than 1.2 mm, cover with 3 mm thick phenolic laminated white sheet cover for mounting fitting like switches, sockets fan regulators etc. including 1.5 Sqmm single core (Green colour) PVC insulated unsheathed copper earth continuity conductor FRLS cable 1100 V grade as continuous earth wire for one light / fan / bell point controlled by one, one way switch.Note :- (i) The Switch / Socket accessories shall be measure and paid separately. (ii) The cost of MS sunken box & cover plate of size as required at site and cutting chases in stone / brick masonry and making good disturbed surfaces using CM 1:3 shall deemed to be included in quoted rate. |
| 113 | M&L for point wiring with 1100 volts grade PVC insulated FRLS multistranded copper conductor cable 1.5 Sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 1.5 Sqmm (Green), concealed in wall and drawn into and including rigid non metallic PVC conduit medium grade not less than 20 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories and terminated in MS sunken box modular metal flush box of thickness not less than 1.2 mm, cover with 3 mm thick phenolic laminated white sheet cover for mounting switches, sockets, fan regulator as required for one 3 pin socket outlet 5 Amps on the same board with other switches, complete all as specified and as directed. |
| 114 | M&L for point wiring with 1100 volts grade PVC insulated FRLS multistranded copper conductor cable 1.5 Sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 1.5 Sqmm (Green), concealed in wall and drawn into and including rigid non metallic PVC conduit medium grade not less than 20 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories and terminated in MS Sunken box of thickness not less than 1.2 mm, cover with 3 mm thick phenolic laminated white sheet cover for mounting switches, sockets, fan regulator as required for 3 pin 5 Amps socket outlet on independent board, complete all as specified and directed.Note :- (i) The Switch / Socket accessories shall be measure and paid separately. (ii) The cost of MS sunken box & cover plate of size as required at site and cutting chases in stone / brick masonary and making good disturbed surfaces using CM 1:3 shall deemed to be included in quoted rate. |
| 115 | M&L for point wiring with 1100 volts grade PVC insulated FRLS multistranded copper conductor cable 2.5 Sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 2.5 Sqmm (Green), concealed in wall, drawn into and including rigid non metallic PVC conduit medium grade not less than 25 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories and terminated in MS Sunken box of thickness not less than 1.2 mm, cover with 3 mm thick phenolic laminated white sheet cover for mounting switches, sockets, fan regulator as required for 3 Pin 15 Amps socket outlet on independent board, complete all as specified and directed.Note :- (i) The Switch / Socket accessories shall be measure and paid separately. (ii) The cost of MS sunken box & cover plate of size as required at site and cutting chases in stone / brick masonary and making good disturbed surfaces using CM 1:3 shall deemed to be included in quoted rate. |
| 116 | M&L for point wiring with 1100 volts grade PVC insulated FRLS multistranded copper conductor cable 4.0 Sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 4.0 Sqmm (Green), concealed in wall, drawn into and including rigid non metallic PVC conduit medium grade not less than 25 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories and terminated in MS Sunken box / modular metal flush box of thickness not less than 1.2 mm, cover with 3 mm thick phenolic laminated white sheet cover for mounting switches, sockets, fan regulator as required for 3 Pin 15 Amps socket outlet on independent board, complete all as specified and directed.Note :- (i) The Switch / Socket accessories shall be measure and paid separately. (ii) The cost of MS sunken box & cover plate of size as required at site and cutting chases in stone / brick masonary and making good disturbed surfaces using CM 1:3 shall deemed to be included in quoted rate. |
| 117 | S&F Modular Switch one way 6 A, 1 module complete all as specified and directed. |
| 118 | S&F Modular Socket, 6A - 2/3 pin combined, 2 module complete all as specified and directed. |
| 119 | S&F modular switch 1 way 16A, 1 module complete all as specified and directed. |
| 120 | S&F modular socket 6A/16A - 2/3 pin combined 2 module complete all as specified and directed. |
| 121 | S&F fan step regulator, 120W - 2 module complete all as specified and directed. |
| 122 | M&L Ceiling rose 3 phase/PVC/polycarbonate, isolated body 65x50mm, three terminals complete all as specified and directed.. |
| 123 | S&F in repair LED lights fitting 1x20 W, 220V,AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed. |
| 124 | S&F in repair LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed. |
| 125 | S&F LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed. |
| 126 | S&F in replacement of Factory made, sheet distribution boards, double door protection class IP-42 suitable for mounting MCBs/ MCCBs with 200 amps rated bus bar complete all as specified and directed,(a) TPN 4 Ways |
| 127 | (b) SPN 8 Ways |
| 128 | S&F in replacement of MCB 10 KA confirming to IS-8828 : 1996, IEC-898 : 1995 rupturing capacity of the under mentioned type and rating :-(a) SP 5 to 32 amps |
| 129 | (b) SPN 40 to 63 Amp |
| 130 | (c) TPN 63 to 100 Amp |
| 131 | M&L for earthing complete with galvanized steel earth plate 600 x 600 x 6mm thick, buried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of the plate not less than 1.5 m below normal ground level, connected to GI wire 4 mm dia as earthing lead by means of bolts, nuts, check nuts & washers of galvanized iron or steel besides building at all joints including excavation and earth work, GI pipe light grade 15mm bore for protection of GI wire from earth electrode, supply and laying charcoal dust, common salt, PCC (1:3:6) type B-1 using 20mm graded stone aggregate for chamber and MS angle iron frame 40x40x3mm and RCC cover 40 mm thick (1:2:4) type B-1 using 20 mm graded stone aggregate Reinforced with 6 mm dia round bars @ 75 mm C/C both ways with MS handle 12 mm dia, PGI funnel and wire mesh, 20 mm bore GI Pipe medium grade for watering complete all as shown in electrical plate No 3 of SSR part-I(2009) and connected to earth test point including testing complete all as specified and directed. Note :- 1. PCC Chammer shall be constructed atleast 2.5 metre away form the earth electrode of the earth pit and pipe for watering shall be provided in slanting manner. 2. GI wire and protection pipe upto 7.5 meter from the earth plate electrode is deemed to be included in quoted rate.3. Excavation for earthing to be done manually and Earth resistance below 3 Ohm should be obtained after measurement for every pit. |
| 132 | M&L for sub main wiring complete with 2 runs of 6 Sqmm single core PVC insulated unsheathed FRLS copper cable 1100 V grade with multistranded copper conductor ISI marked drawn through and including PVC rigid conduit / casing capping not less than 20mm and conduit accessories fixed on surface of wall / celing etc including provision of 1 Run of 6 Sqmm PVC insulated unsheathed FRLS cable with multistranded copper conductor as earth continuity complete all as specified and directed. Note : 02 Run of 06 Sqmm copper wire and 01 Run of 06 Sqmm copper earth wire along with PVC conduct shall be measured as one unit. |
| 133 | S&F exhaust fan, made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, copper winding of sweep of size 250mm complete all as specified and directed. |
| 134 | Taking down and dismantling ceiling fan of any size including accessories of any type or make, transportation, bringing back to site, safely and re-fixing after oiling, greasing and servicing in serviceable condition including repair of shaft / starter / rotor etc., provision of cable from ceiling rose or connector to fan including painting of fan by one coat of synthetic enamel paint of in white / off white colour by spraying including filling cavities with filler, after cleaning all dust etc. including writing Fan No. on each fan complete all as specified and directed. |
| 135 | S&F ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep with minimum air delivery 210 cubic meter per minute (CMM) with service value 6.00 BEE, five star rated with brushless direct current motor (BLDC) remote control operated complete all as specified and directed.Note:- The rate quoted by contractor shall deemed to be included for the followings : (i) The colour BLDC Fan shall be pearl white. (ii) Proper hanging arrangement like 0.45 meter down rod, canopy etc. (iii) Writing the Fan No. on fan body.(iv) Making connection with 1.5 Sqmm copper wire complete all as directed. |
| 136 | M&L for taking out of split/Window type AC of 1.5/2.0 ton capacity from existing location, cleaning of condenser, cooling coil, and other components with cooling coil rinse solution and clean water, greasing of fan, motor, blower etc without damage any part and re-install at the same location complete all as specified and directed. |
| 137 | M&L for Telephone wiring HDPE insulated PVC shethed 2 Pair X 0.4 sqmm gray shedded colour insulation thickness 0.65mm strandred conductor, rurrent capacity 15A , insulation thickness 0.65mm solid conductor RG-6 CO-axial PVC in black clour drawing into and including concealed rigid non metallic PC conduit, medium grade , ISI marked ivory colour along with accessories in 20mm dia conduit and terminated each RJ 11 telephone socket all as directed. |
| 138 | S&F RJ 11 telephone socket 1 Module |
| 139 | M&L in repair for XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 35 sq. mm 3.5 core complete all as specified and directed. Note - Excavation,earth work,sand,brick and protection pipe shall be measured and paid seperately. |
| 140 | Excavation in trenches n.exc 1.5 metre wide and n.exc 1.5 metre in depth for foundation etc or for shafts, wells, cess pits, manholes, pier holes, laying cables errection of poles / struts/stays etc n.exe 10 Sqm on plan not exceeding 1.5 metre in depth and getting out in any type of soil. |
| 141 | Returning, filling in, including spreading, levelling, watering and well ramming in layers n.exc 25cm in any type of soil. |
| 142 | Removing of excavated material (soil) to a distance n.exc 50 metre and depositing where directed at a level n.exc 1.50metre above the starting point |
| 143 | M&L for laying of bricks subclass ‘B’ old size laid flat perpendicular to the direction of cable for protection of cable complete all as specified. |
| 144 | M & L Sand cushioning to PVC under ground cable with tibba sand and punning to provide a required cover. |
| 145 | S&F sheet metal enclosure with socket plug top and MCBs single pole and neutral enclosure with a two pin and earth plug and socket with one single pole MCB of capacity 20 Amps complete all as directed. |
| 146 | Schedule of Credit Total in Figures 0.0 0.0 -55779.0 Quoted Rate in Figures Select 0.0 0.0 Zero Only 0.0 Quoted Rate in Words INR Minus Fifty Five Thousand Seven Hundred & Seventy Nine Only Please Enable Macros to View BoQ information |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
