|
| 1 | Dismantling tiled floors laid in mortar upto floor two level including stacking of serviceable materials and disposal of un-serviceable materials within 20 metres lead For thickness of tiles upto 25mm |
| 2 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) |
| 3 | Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge. |
| 4 | Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.In cement mortar |
| 5 | Dismantling roofing including ridges, hips, valleys and gutters etc., and stacking the material within 50 metres lead of: |
| 6 | Dismantling wooden ballies in posts and struts including stacking within 50metres lead. |
| 7 | Dismantling wooden boardings in lining of walls and partitions, excluding supporting members but including stacking within 50 metres lead :Thickness above 10 mm up to 25 mm |
| 8 | Dismantling wood work in frames, trusses, purlins and rafters up to 10 metres span and 5 metres height including stacking the material within 50 metres lead : Of sectional area 40 square centimetres and above |
| 9 | Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead :Of area 3 sq. metres and below |
| 10 | Demolishing stone rubble masonry manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge : |
| 11 | Dismantling steel work upto span of 10 metres and height between ridge and floor level upto 5 metres in single sections including dismantling and stacking the materials within 20 metres lead (Riveted work where rivets are required to be cut shall be measured and paid for separately). Channels, angles, tees and flats: |
| 12 | Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means in all heights and depths or in foundation trenches etc. in all kinds of soil including saturated soils comprising of pick work, jumper work and blasting work both in soft and hard rock with chiesling and wedging out of rock (where blasting is prohibited and their intermediate classifications soils including dewatering where ever required, setting out to required lines, levels as shown on the drawing and directed by the Engineer-in-charge at site, according to the CPWD specification and sorting out useful and unuseful material and transportation of the unuseful material for disposing at dumping site including prescribed dumping charges to be arranged by the contractor himself to the satisfaction of Engineer-in-Charge through all modes of transportation including head load, animal load or mechanical means along with its leveling fine dressing and with all kinds of labour machineries, tools equipments and safety measures and incidentals necessary to complete the work wise mechanical means and labour (if required) all useful material such as stones,shingles aggregate and slates shall be properly stacked at site to the meximum possible extent in all leads and lifts through all modes of transportation and used/removed as per the direction of Engineer-in-charge. Any loss to the public and private property during the course of execution and disposal of serviceable and unserviceable materials shall be the absolute responsibility of the contractor including carriage of materials within all leads and lifts in all respect including all incidental charges:- All kinds of soil. |
| 13 | Earth work in cutting by mechanical means (Hydraulic excavator)/ manual means in all heights and depths in all kinds of soil including saturated soils comprising of pick work, jumper work and blasting work both in soft and hard rock with chiesling and wedging out of rock (where blasting is prohibited and their intermediate classifications soils including dewatering where ever required, setting out to required lines, levels as shown on the drawing and directed by the Engineer-in-charge at site, according to the CPWD specification and sorting out useful and unuseful material and transportation of the unuseful material for disposing at dumping site excluding prescribed dumping charges to be arranged by the contractor himself to the satisfaction of Engineer-in-Charge through all modes of transportation including head load, animal load or mechanical means along with its leveling fine dressing and with all kinds of labour machineries, tools equipments and safety measures and incidentals necessary to complete the work wise mechanical means and labour (if required) all useful material such as stones,shingles aggregate and slates shall be properly stacked at site to the meximum possible extent in all leads and lifts through all modes of transportation and used/removed as per the direction of Engineer-in-charge. Any loss to the public and private property during the course of execution and disposal of serviceable and unserviceable materials shall be the absolute responsibility of the contractor including carriage of materials within all leads and lifts in all respect including all incidental charges:- All kinds of soil. |
| 14 | Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m :Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia. |
| 15 | Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete including carriage of materials in all leads and lifts. |
| 16 | Centering and shuttering including strutting, propping etc. and removal of form for : (3.01)Foundations, footings, bases of columns, etc. for mass complete including carriage of materials in all leads and lifts and as per direction of Engineer-in Charge. |
| 17 | Flat surface such as soffits of suspended floor, roof, landings and lke complete including carriage of materials in all leads and lifts and as per direction of Engineer-in Charge. |
| 18 | Columns, pillars, posts etc. ( rectangular or square in plan).complete including carriage of materials in all leads and lifts and as per direction of Engineer-in Charge. |
| 19 | Beams, cantilever, girders and lintels.complete including carriage of materials in all leads and lifts and as per direction of Engineer-in Charge. |
| 20 | Stairs, (excluding landings) except spiral stair cases including carriage of materials in all leads and lifts and as directed by the Engineer in Charge. |
| 21 | Centering and shuttering including strutting, propping etc. and removal of form work for :Retaining walls, return walls, walls (any thickness) including attached pilasters, buttresses, plinth and string courses fillets, kerbs and steps etc. |
| 22 | Edges of slabs and breaks in floors and walls Under 20cm wide complete including carriage of materials in all leads and lifts and as per direction of Engineer-in Charge. |
| 23 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:5:10 (1 cement : 5 coarse sand): 10 graded stone aggregate 40 mm nominal size) complete including carriage of materials in all leads and lifts and as per direction of Engineer-in Charge. |
| 24 | Providing and laying cement concrete 1:4:8 (Icement 4sand: 8 graded stone aggregate 40m curing complete excluding cost of form work in foundation and plinth in breast and retaining walls complete including carriage of materials in all leads and lifts and as per direction of Engineer-in Charge. |
| 25 | Providing and laying cement concrete in , walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing :1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) |
| 26 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : (i) 1:2:4 (1 cement : 2 coarse sand) : 4 graded stone aggregate 20 mm nominal size) complete including carriage of materials in all leads and lifts and as per direction of Engineer-in Charge. |
| 27 | Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.(i) All work up to plinth Level |
| 28 | Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.(i) All work plinth level up to all Level |
| 29 | Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing:(i) 1:1½:3 (1 cement : 1½ coarse sand) : 3 graded stone aggregate 20 mm nominal size). |
| 30 | Providing and laying water proofing treatment with Dr. Fixit-FASTFLEX or equivalent with two components polymer modified cementitious coating consisting of cementitious powder and a polymer liquid in two coats for first coat:- clean and saturate surface and then applying a coat of Dr. Fixit -FASTFLEX by maintaning a coverage of 6-7sft per kg to achive one mm thickness and the same process shalltended upto 300 mm vertically. The second coat shall be applied in opposit direction after four six-hours of application of first coat then sprinkle sand on top surface of applied Dr. Fixit-FASTFLEX while still tacky over the second coat. Then apply cement mortar 1 ; 4 (1 cement :4 sand) admioxed with 200ml of pidiproof LW @ 200ml per 50kg bag of cement over the floor with the suitable grediant towards drain pipe, while the second coat of Dr. Fixit is still tacky complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 31 | Providing Tor steel reinforcement for reinforced cement concrete work including bending binding and placing in position and cost of binding wire complete up to all floor levels/all heights.as per HP.PWD specification 1990 (One thousand Nine hundred Ninety) Volume-I, including carriage of all labour equipments and materials to various location through all modes of transportation within all leads, lifts and other incidential charges |
| 32 | Applying cement slurry on RCC slab or cement concrete work using 2.75 kg of cement per squaremetre of floor area complete including carriage of materials in all leads and lifts and as per direction of Engineer-in Charge. |
| 33 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand) including carriage of material in all leads and lifts : |
| 34 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in Cement mortar 1:4 (1 cement :4 coarse sand) including carriage of materials within all leads and lifts. |
| 35 | 28 Cm. Thick Cavity Wall with 11.5 C. Brick wall & 5 CM. Cavity Filled with EPS/ XPS ( Expanded Polystyrene High Thermal resistance) plus complience in common burnt clay FPS ( non Modular) Bricks of class designation 7.5 in superstructure in cement mortar1:4 ( 1 Cement : 4 Sand)( one side face to be measured and paid accordingly) |
| 36 | Stone soling properly hand-packed filling interstices with Kharanja stone under floor specified thickness complete as per HP.PWD specification including carriage of material within all leads and lifts as per direction of Engineer-in-charge. |
| 37 | Stone filling behind retaining wall per HP.PWD specification 1990 Volume-I complete including carriage of materials in all leads and lifts and as per direction of Engineer-in Charge. |
| 38 | Providing weep holes in brick masonry/stone masonry/plain reinforced concrete abutment, wing wall, return wall with 100mm (one hundred milimeter) dia PVC pipe extending through the full width of the structure with slope of 1 (V):120 (one hundred twenty) (H) towards drawing face complete as per drawing and technical specification clause 614, 709, 1204.3.7(six hundred fourteen, seven hundred nine, one thousand two hundred four pont three point seven) as per MORD specification including carriage of all labour, equipment and material to various location through all modes of transportation in all leads, lifts and all incidental charges. |
| 39 | Providing and Fixing wood work in frames of doors windows and clearystory window (I) Second class Deodar wood complete including carriage of materials in all leads and lifts and as per direction of Engineer-in Charge. |
| 40 | Providing and fixing Factory Made Flush Doors 35 MM Thick Ply board i.e Non Decorative Phenol Bonded Termite Resistant and water proof Core of Block Board Construction with Full Frame of First class Hard wood and well matched Commercial Three Ply Veneer with vertical Grains Or Cross band and Face Veneered on both Faces of flush door including enamelled M.S. butt hinges with necessary screws within all leads, lifts of materials and other incidentals |
| 41 | Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge. (Note:- Butt hinges and necessary screws shall be paid separately) Deodar wood 40mm thick shutters. |
| 42 | Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of IS gauge designation 85-G with a wire of dia 0.56(Zero decimal Fifty six milimetres) for doors and windows and clerestory windows (i) 35mm thick Wire Gauge Shutters |
| 43 | Providing and fixing 19mm (Nineteen milimetre) thick HDMR Board Shelves including Necessary Screws , complete including carriage of materials in all leads and lifts and as per direction of Engineer-in Charge. |
| 44 | Providing and fixing 19mm (Nineteen milimetre) thick HDMRl board shutter for cup board etc. complete including carriage of materials in all leads and lifts and as per direction of Engineer-in Charge.Nickel plated bright finished piano hinges. |
| 45 | Providing and fixing 1.00mm thick coloured or plain laminated sheet (sunmica) on boards / ply wood sheets with approved adhesive and nails complete including carriage of materials in all leads and lifts and as per direction of Engineer-in Charge. |
| 46 | Providing and fixing plain M.S. Grills of required pattern in steel frames of windows and ventilators etc, complete including carriage of materials in all leads and lifts and as per direction of Engineer-in Charge. |
| 47 | Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS: 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete including carriage of materials in all leads and lifts and as per direction of Engineer-in Charge. 250x16 mm |
| 48 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete including carriage of materials in all leads and lifts and as per direction of Engineer-in Charge.:200x10 mm |
| 49 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete including carriage of materials in all leads and lifts and as per direction of Engineer-in Charge. 125 mm |
| 50 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete including carriage of materials in all leads and lifts and as per direction of Engineer-in Charge.. 75 mm |
| 51 | Providing and fixing oxidized single acting Door spring with necessary screws etc. complete including carriage of materials in all leads and lifts and as per direction of Engineer-in Charge. 150 mm |
| 52 | Providing and fixing oxidized M.S. hasps and stapple for cup board 90 mm size complete including carriage of materials in all leads and lifts and as per direction of Engineer-in Charge. |
| 53 | Providing and fixing 150mm (one hundred fifty milimetre) oxidized M.S. hooks and eyes.complete including carriage of materials in all leads and lifts and as per direction of Engineer-in Charge. |
| 54 | Providing anf Fixing Ready made PVC Edging for cup Board in Edging completye in all respect with necessary nails complete including carriage of materials in all leads and lifts and as per direction of Engineer-in Charge. |
| 55 | Providing and fixing Magnetic catcher with screws etc. complete including carriage of materials in all leads and lifts and as per direction of Engineer-in Charge. lifts and other incidentals. |
| 56 | Providing and fixing 40 X 3 mm flat iron holdfast 40 cm. Long including fixing to frame with 10 mm diametre bolts and nuts and wooden plugs and embeded in cement concrete blocks 30 x 10 x 15 cm. 1;3;6 ( 1 cement : 3 sand : 6 graded stone aggregate 20 mm nomonal size) |
| 57 | Providing and fixing M.S. curtain rod Powder coated 25 mm dia including clamps, finells with brackets plugs etc. complete including carriage of materials in all leads and lifts and as per direction of Engineer-in Charge. |
| 58 | Mirrior Polished Kota stone slab flooring 19mm thick 55x55CM. of Uniform Colour with Double Nosing base of cement mortor 1:4 (1 cement :4 sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab. Including rubbing and mirror polishing etc. complete :-25 mm thick (average) slab size not less than 550mmx550mm including carriage of material within all leads and lifts as per direction of Engineer-in-charge. |
| 59 | Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. |
| 60 | Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. |
| 61 | Providing and laying ceremic glazed wall tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete . |
| 62 | Granite work gang saw cut (polished and machine cut) of thickness 20 mm for wall lining (veneer work), backing filled with a grout of average 12 mm thick in cement mortar 1:3 (1 cement : 3 coarse sand), including pointing with white cement mortar 1:2 (1 white cement : 2 marble dust) with an admixture of pigment to match the marble shade (To be secured to the backing by means of cramps, which shall be paid for separately. all complete as per the direction of Engineer-in-charge |
| 63 | Providing and laying marble work (Table rubbed and polished) in flooring 20mm. thick base in cement mortar 1:3 (1cement:3sand) including jointing with cement mortar 1:2(1 white cement:2 marble dust) with an admixure of pigment to match the shade of the marble:- 20mm thick Baroda green marble including carriage of materials within all leads and lifts. |
| 64 | Providing and laying marble work (Table rubbed and polished) in flooring 20mm. thick base in cement mortar 1:3 (1cement:3sand) including jointing with cement mortar 1:2(1 white cement:2 marble dust) with an admixure of pigment to match the shade of the marble:- 20mm thick Jaisalmer Yellow Marble Slab single Piece including carriage of materials within all leads and lifts. |
| 65 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. |
| 66 | Providing and fixing precoated galvanised steel sheet roofing accessories 0.60 mm (+ 0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 1518 microns using self drilling/ self tapping screws complete : Ridges plain (500 - 600mm) |
| 67 | Providing and fixing precoated galvanised steel sheet roofing accessories 0.60 mm (+ 0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 1518 microns using self drilling/ self tapping screws complete :Valley plain (800 - 900mm) |
| 68 | Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+ 0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 1518 microns using self drilling/ self tapping screws complete : Having 30CM Deep and 30 Cm. Wide Gutter (900 mm over all girth) |
| 69 | Providing and fixing 2mm thick Ms Sheet in window chajja/ ceiling /including cutting fixing and welding to steel roof members and applying a coat of red lead primer complete as per the instruction of Engineer-in-charge ( base members of steel work shall be measured and paid seperately ). |
| 70 | Providing and fixing on wall face PVC 110 mm Dia pipe of Kitec ( PE-AL-PE) Multi Layer Composite Pressure pipe . including filling the joints with approved adhesive complete including carriage of materials in all leads and lifts and as per direction of Engineer-in Charge. |
| 71 | Providing and fixing on wall face PVC 110 mm Dia Plain Bend of Kitec ( PE-AL-PE) Multi Layer Composite Pressure pipe accessories for rain water pipes including filling the joints with approved adhesive complete including carriage of materials in all leads and lifts and as per direction of Engineer-in Charge. |
| 72 | PVC Plain Shoe 110mm(One hundred fifty milimetre) dia. of Kitec ( PE-AL-PE) Multi Layer Composite Pressure pipe accessories for rain water pipes including filling the joints with approved adhesive complete including carriage of materials in all leads and lifts and as per direction of Engineer-in Charge. |
| 73 | PVC Collar 110mm(One hundred fifty milimetre) dia.of Kitec ( PE-AL-PE) Multi Layer Composite Pressure pipe accessories for rain water pipes including filling the joints with approved adhesive complete including carriage of materials in all leads and lifts and as per direction of Engineer-in Charge. |
| 74 | Providing and fixing PVC holder bat clamps of approved design to PVC. pipes embedded in with screws and Nail s and Plugs etc complete including carriage of materials in all leads and lifts and as per direction of Engineer-in Charge. |
| 75 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(i) Hot finished welded type tubes |
| 76 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.( Aplo Make) In gratings, framed, guards, bars ladders and railing, brackets including hollow sections of various sizes and similar works |
| 77 | Painting two coats(excluding priming costs)on new steel and other metal surfaces withsatin enamel paint complete including carriage of materials in all leads and lifts and as per direction of Engineer-in Charge. |
| 78 | Applying priming coat over new wood and wood based surfaces with ready mixed paint brushing wood primer pink.complete including carriage of materials in all leads and lifts and as per direction of Engineer-in Charge. |
| 79 | Painting two coats (excluding priming costs) on new wood and wood based surfaces with enamel paint brushing complete including carriage of materials in all leads and lifts and as per direction of Engineer-in Charge. |
| 80 | 6mm (Six milimetre) cement plaster to ceiling in cement mortar 1:3 (One Cement is to Three Sand) in all floor level. complete including carriage of materials in all leads and lifts and as per direction of Engineer-in Charge. |
| 81 | 15mm (Fifteen milimetres) thick cement plasters in single coat on fair side of brick/concrete/stone walls for interior plastering upto all floor level complete including carriage of materials in all leads and lifts and as per direction of Engineer-in Charge. |
| 82 | 15mm (Fifteen milimetres) thick cement plasters in single coat on rough side of brick/concrete/stone walls for interior plastering upto all floor level complete including carriage of materials in all leads and lifts and as per direction of Engineer-in Charge. |
| 83 | Finishing wall with weather proof water based modified Acrylic Emulsion ( of approved Shade) Such as apex or Asian paints or vits Equivalent complete including carriage of materials in all leads and lifts and as per direction of Engineer-in Charge. |
| 84 | Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade one or more coats on old work complete including carriage of materials within all leads and lifts. |
| 85 | Applying white cement based wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete including carriage of materials in all leads and lifts and as per direction of Engineer-in Charge. |
| 86 | Providing and fixing moulded hand rail of M.S. hollow pipe 50 mm dia welded in straight lenght over M.S. flat at top of vertical balusters including one coat of red oxide priming coat complete (M.S. flat & balusters of railings shall be mesaured & paid separetely. |
| 87 | Providing and Fixing Decorative Wall bracket of Size 30x30 Cm with S Sheet Cut into Shape and welded togother with MS Flat 50x3mm to Form Bracket complete detail Complete as per Architect Drawing including Fixing in position Complete as per the Direction of Engineer- in Charge. |
| 88 | Providing and fixing Polyethelene-Aluminium- Polyethelene PE-AL-PE Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 metre spacing. This includes the costs of cutting chases and including testing of joints complete as per direction of the engineer in charge Concealed work, including cutting chases and making good the wall etc..(i) 1216 (16 mm OD) pipe |
| 89 | Providing and fixing Polyethelene-Aluminium- Polyethelene PE-AL-PE Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 metre spacing. This includes the costs of cutting chases and including testing of joints complete as per direction of the engineer in charge Concealed work, including cutting chases and making good the wall etc..(i) 1620 (20 mm OD) pipe |
| 90 | Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall complete including carriage of materials in all leads and lifts and as per direction of Engineer-in Charge.(i) 15mm Nominal Bore |
| 91 | Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall :(i) 25mm Nominal Bore |
| 92 | Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall :(i) 40mm Nominal Bore |
| 93 | Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete including carriage of materials in all leads and lifts and as per direction of Engineer-in Charge. :(i) 25 to 40 mm nominal bore |
| 94 | Providing and fixing enclosed type water meter (bulk type) conforming to IS : 2373 and tested by Municipal Board complete with bolts, nuts, rubber insertions etc. (The tail pieces if required will be paid separately) :(i) 15mm Nominal Bore |
| 95 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) complete including carriage of materials in all leads and lifts and as per direction of Engineer-in Charge.:- (i) 20 mm nominal bore. |
| 96 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) including carriage of materials within all leads and lifts:- (i) 15 mm nominal bore. |
| 97 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 98 | Providing and fixing brass ball valve (horizontal plunger type)-:High pressure with polythene plastic floats 15mm nominal bore complete including carriage of materials in all leads and lifts and as per direction of Engineer-in Charge. |
| 99 | Providing and fixing vitreous China Hindware Make Single piece Cat No.92077 (S-11)wash down, water closet (European type. W.C. pan) one piece with integral 'P' or 'S' trap including cistern seat and cover jointing the trap with soil pipe in cement mortar 1:1(1 cement : 1 sand) including carriage of materials within all leads and lifts:-Complete set. |
| 100 | Providing and fixing Hindware make make viterous china wash basinwith pedestal 55x40x83 cm pillar tap with C.I. or M.S. brackets painted white including cutting holes and making good the same but excluding fitting including carriage of materials in all leads and lifts:- . |
| 101 | Providing and fixing towel ring complete including carriage of materials in all leads and lifts and as per direction of Engineer-in Charge. |
| 102 | Providing and fixing 610 mm size C.P. brass towel rail or equivalent complete with C.P. brass brackets fixed to wooden plugs with C.P. brass screws complete including carriage of materials in all leads and lifts and as per direction of Engineer-in Charge. |
| 103 | Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete. |
| 104 | Providing and fixing C.P. toilet paper holder of complete including carriage of materials in all leads and lifts and as per direction of Engineer-in Charge. |
| 105 | Providing and fixing C.P. sink mixer with casted botton swinging spaut at top complete including carriage of materials in all leads and lifts and as per direction of Engineer-in Charge. |
| 106 | Providing and fixing 15 mm dia C.P. brass centre hole basin mixture with capstain head including carriage of materials within all leads and lifts. |
| 107 | Providing and fixing C.P. brass bib cock 15mm (fifteen millimetre) nominal bore complete including carriage of materials in all leads and lifts and as per direction of Engineer-in Charge. |
| 108 | Providing and fixing 15 mm dia CP Brass Angle Cock of approved quality and make complete including carriage of materials in all leads and lifts and as per direction of Engineer-in Charge. |
| 109 | Providing and fixing 15mm dia Health faucet fitting complete including carriage of materials in all leads and lifts and as per direction of Engineer-in Charge. |
| 110 | Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make complete including carriage of materials in all leads and lifts and as per direction of Engineer-in Charge. |
| 111 | Providing and fixing chromium plated soap dish Ess Ess make with C.P. Brass brackets fixed to wooden cleats with C.P. Brass screws etc. complete including carriage of materials in all leads and lifts and as per direction of Engineer-in Charge. |
| 112 | Providing and fixing uplasticised PVC connection pipe with brass unions complete including carriage of materials in all leads and lifts and as per direction of Engineer-in Charge. Make viking.45 cm length (i) 15 mm nominal bore |
| 113 | Providing and fixing PVC floor traps ISI marked of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. complete including carriage of materials in all leads and lifts and as per direction of Engineer-in Charge.:-110mm x 75mm |
| 114 | Providing and fixing high pressure PVC Pipe of Kitec Multi Layer of composit pressure spigot and socket, waste and ventilating pipes ISI marked with collar and clamps including fixing with approved adhesive etc. complete including carriage of materials in all leads and lifts and as per direction of Engineer-in Charge.110mm |
| 115 | Providing and fixing high pressure PVC Pipe of Kitec Multi Layer of composit pressure spigot and socket, waste and ventilating pipes ISI marked with collar and clamps including fixing with approved adhesive etc. complete including carriage of materials in all leads and lifts and as per direction of Engineer-in Charge. 75mm |
| 116 | Providing and fixing PVC Kitec Multi Layer of composit pressure single equal branch plain complete including carriage of materials in all leads and lifts and as per direction of Engineer-in Charge. 110mm |
| 117 | Providing and fixing PVC Kitec Multi Layer of composit pressure single equal branch plain complete including carriage of materials in all leads and lifts and as per direction of Engineer-in Charge. 75mm |
| 118 | Providing and fixing PVC Kitec Multi Layer of composit pressure Plain bend ISI marked including fixing with approved adhesive etc.complete including carriage of materials in all leads and lifts and as per direction of Engineer-in Charge.:110mm |
| 119 | Providing and fixing PVC Kitec Multi Layer of composit pressure Plain bend ISI marked including fixing with approved adhesive etc. complete including carriage of materials in all leads and lifts and as per direction of Engineer-in Charge.:75mm |
| 120 | Providing and fixing PVC Kitec Multi Layer of composit pressure door bend ISI marked including fixing with approved adhesive etc. complete including carriage of materials in all leads and lifts and as per direction of Engineer-in Charge. 110mm |
| 121 | Providing and fixing PVC Kitec Multi Layer of composit pressure door bend ISI marked including fixing with approved adhesive etc.complete including carriage of materials in all leads and lifts and as per direction of Engineer-in Charge. 75mm |
| 122 | Providing and fixing PVC Kitec Multi Layer of composit pressure Coller ISI marked including fixing with approved adhesive etc. complete including carriage of materials in all leads and lifts and as per direction of Engineer-in Charge.:110 mm |
| 123 | Providing and fixing PVC Kitec Multi Layer of composit pressure Coller ISI marked including fixing with approved adhesive etc. complete including carriage of materials in all leads and lifts and as per direction of Engineer-in Charge.:75mm |
| 124 | Providing and fixing PVC Kitec Multi Layer of composit pressure embeded in and including cement concrete blocks 10x10 cm of 1:2:4 mix ( 1 cement : 2 sand : 4 graded stone aggregate 20 mm nominal size) and cost of cutting holes etc. including carriage of materials within all leads and lifts:110mm |
| 125 | Providing and fixing PVC Kitec Multi Layer of composit pressure embeded in and including cement concrete blocks 10x10 cm of 1:2:4 mix ( 1 cement : 2 sand : 4 graded stone aggregate 20 mm nominal size) and cost of cutting holes etc. complete including carriage of materials in all leads and lifts and as per direction of Engineer-in Charge.:75mm |
| 126 | Providing and fixing 100mm dia round C.P grating of approved quality complete including carriage of materials in all leads and lifts and as per direction of Engineer-in Charge. |
| 127 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.40 mm dia complete including carriage of materials in all leads and lifts and as per direction of Engineer-in Charge. |
| 128 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete including carriage of materials in all leads and lifts and as per direction of Engineer-in Charge. |
| 129 | Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (medium duty) 500 mm internal diameter, total weight of cover and frame to be not less than 116 kg (weight of cover 58 kg and weight of frame 58 kg) ::(i) With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 130 | Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality L D- 2.5 Rectangular shape 600x450 mm internal dimensions.complete including carriage of materials in all leads and lifts and as per direction of Engineer-in Charge. |
| 131 | Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design:100x100 mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 132 | Cutting holes of required size in brick masonry wall for fixing of exhaust fan including providing and fixing 300 mm dia PVC pipe conforming BIS-12818 and making good the same etc. complete as per direction of Engineer-in-charge. |
| 133 | Providing and fixing sluge transfer pump capacity -1.50m3/ hour @10mtr head make kirloskar/willo model-SPOM complete including carriage of materials in all leads and lifts and as per direction of Engineer-in Charge.. |
| 134 | Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete including carriage of materials in all leads and lifts and as per direction of Engineer-in Charge. (New work) : (i) 15 mm Nominal Bore |
| 135 | Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete including carriage of materials in all leads and lifts and as per direction of Engineer-in Charge. (New work) : (i) 20mm Nominal Bore |
| 136 | Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete including carriage of materials in all leads and lifts and as per direction of Engineer-in Charge. (New work) : (i) 25 mm Nominal Bore Please Enable Macros to View BoQ information |
