|
| 1 | Material and Labour for Cement concrete type B-2 ,1:3:6 (40 mm graded) in floor, foundations, filling and mass concrete, including Demolition of existing cement concreteof any type, complete all as specified and directed. |
| 2 | Taking down existing cement plaster/screed, roughening surfaces of old concrete roof slab/chajjas by picking, sweeping clean and washing down with water to remove dust, etc., brushing neat cement slurry with 3.0 kg of cement per sq. metre and rendering 10 mm thick, cement plaster/screed, in cement mortar (1:3) mixed with water proofing compound as per manufactures instructions (waterproofing compound measured and paid seperately) and finishing surface even and smooth without using extra cement including provision of water proofing treatment over smooth finished surfaces by application of cold applied bituminous primer as per manufacturer's instructions, providing and laying 3.00 mm thick, plain finish, APP modified bitumenous waterproofing and damp proofing membrane with polyester reinforcement (Non-Woven Polyester Mat), conforming to IS 16532 :2017 (Dimensions and weight of APP membrane polyester as per Table 2 of IS), by forced (torch on) application, with minimum 75 mm overlap on longitudinal direction and 100 mm overlap on the transverse direction, complete all as specified and directed. |
| 3 | Supply only liquid water proofing compound (ISI), complete all as specified and directed. |
| 4 | S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws including dismantiling of Asbestos roof sheet and remove all debris outside the MOD land, compete all as specified and as directed. |
| 5 | S&F Pre-painted galvalume aluminum zinc coating GI based plain steel 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws incl dismantiling, compete all as specified and as directed. |
| 6 | Materials and Labour for plain cement concrete (1:2:4) type B0 using 12.5 mm graded aggregate in filling gaps between roofing sheets and walls (Gap size 60 mm wide and 40mm-60 mm deeep), rounded or chamfered on edges, including demolition of existing cement concrete, complete all as specified and directed. |
| 7 | Materials and Labour for black hollow steel Section for structural use, conforming to IS 4923:1997 (Reaffirmed 2009), designation CF, in roof trusses (framed), trussed purlins, posts, crane gantries, rails and fastening and heavy brackets framing (square or rectangular hollow sections), including distance pieces cleats etc, complete all as specified and directed. |
| 8 | M&L for Second Class Hardwood timber Scantling unframed work Clean sawn in scantling complete including dismantling of timber scantling 40 Sq. Cm and over in sec in any position as in framed work, complete all as specified and as directed |
| 9 | Supply and Fixing in repair for Anodised aluminium snap grid of Size 600X600mm' frame work for false ceiling with HPSC 4 mm thick Non asbestos fibre cement building boards white colour designer type ready to fix, fixed or laid/ inserted to timber/GI/Aluminium framework as in Ceiling with including proper hanging arrangement after dismantling wall and celling board (fibre, pulp, insulation, glass etc) any thickness including cover fillets, complete all as specified and as directed. |
| 10 | S& F Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per direction of Engr in charge, including dismantling existing wall paneling, complete all as specified and as directed |
| 11 | S& F 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per as per direction of Engr in charge, including dismantling of existing framing, fillet etc., complete all as specified and as directed. |
| 12 | Material and Labour for 2nd class hardwood plain fillets, square, rectangular or triangular in section Exc, 13 Sqcm & n exc 25 Sqcm in cross sectional area, clean sawn, secured with nails or brads, including dismantling timber scantlings in fillets, rails, posts, rafters,purlins, etc. under 40 sq. cm in section (unframed), complete all as specified and directed. |
| 13 | S&F in repairs 150 mm aluminium handles, cast type, anodised, complete all as specified and directed. |
| 14 | S&F in repairs 200 mm long aluminium anodised barrel tower bolts of extruded section, complete all as specified and directed. |
| 15 | S& F in repairs Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed, complete all as specified and as directed. |
| 16 | S&F in repairs door closer of aluminium (extruded section) hydraulically regulated, designation No 3, universal type, suitable for door shutters of 851 to 1000mm in width and of weight between 61 to 80 kg and fixed, complete all as specified and directed. |
| 17 | Brick work with sub class 'B' bricks, straight or curved on plan, exceeding 6 metre mean radius built in cement mortar 1:6 including Demolition of brick work or stone masonry built in cement mortar, complete all as specified and directed. |
| 18 | M&L for Rendering 15 mm thick in CM 1:6 on fair faces of brick work or concrete surfaces, finished even & smooth without using extra cement, complete all as specified and directed. |
| 19 | M&L for Rendering 5 mm thick in cement Plater of CM 1:4 on fair faces of brick work or concrete surfaces, mixed with integral water proofing compound as per manufacturers instructions over and including 10 mm thick backing coat in cement mortar 1:4 on fair faces of brick work or concrete surfaces finish even and smooth without using extra cement complete all as specified and as directed.(Note: Water proofing compound shall be measured and paid seperately under relevant item). |
| 20 | M&L for Rendering 5 mm thick in cement Plater of CM 1:4 on fair faces of brick work or concrete surfaces, mixed with integral water proofing compound as per manufacturers instructions over and including 10 mm thick backing coat in cement mortar 1:4 on fair faces of brick work or concrete surfaces finish even and smooth without using extra cement including taking down cement plaster, any description on brick or stone walls/ceiling etc including racking out joints, hacking for key, scrubbing down with water etc, complete all as specified and as directed.(Note: Water proofing compound shall be measured and paid seperately under relevant item) |
| 21 | Materials and Labour for rendering 15 mm thick, cement plaster, in cement mortar (1:6) on surface other than fair face of brickwork and finishing surface even and smooth without using extra cement, including taking down cement plaster, any description on brick or stone walls/ceiling etc including racking out joints, hacking for key, scrubbing down with water etc. complete all as specified and as directed. |
| 22 | Material and Labour for prepration of newly plastered or previously untreated surfaces and applying two coat oil bound distemper over one coat of primer over a coat of wall care putty 1 mm thick on wall, complete all as specified and directed. |
| 23 | Material and Labour for washing, rubbing down and stopping of distempered and painted surfaces and applying one coat of oil bound distemper over a coat of wall care putty 1mm thick on wall, complete all as specified and directed. |
| 24 | Material & Labour for applying one coat of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces, complete all as specified and directed. |
| 25 | Materials and Labour for 4 mm thick, 3 Nos. ply, plywood, grade BWR, type BB, fixed with screws to timber frame work, including dismantling existing wall and ceiling boards (fibre, pulp, insulation,etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets, complete all as specified and directed. |
| 26 | Disconnecting water tank, float valve with float arm and outlet pipe from PVC service water tank, emptying stored water through outlet, cleaning and removing all scale and dirt etc from tanks and from mouths of circulating pipes etc and finally washing the internal surfaces with bleaching powder, closing wash outlet, refixing water tank, float valve and outlet in proper position, closing the top cover including minor repair if required and testing complete including writing \\"Cleaned on: (Date)\\" 50 mm height on outer face of tank with white paint (USING STENCIL) on water tank of capacity exc 250 litres but n exc 500 litres complete all as directed by Eng in charge. |
| 27 | Taking down of existing aluminium door carefully except Floor spring/hydraulic door closer from the existing frame and repair the same for smooth operation/movement, including replacing of door handle, aluminium hinge, rubber beat etc and refixing in the same location after repairing all components complete all as specified and directed. (Area of door not exc 4.00 Sqm) |
| 28 | Material and labour for preparing new wood & wood based surfaces of any descriptions exc 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and as directed. |
| 29 | Material and labour for preparing old wood & wood based surfaces of any descriptions exc 10 cm width or girth and applying a coat of synthetic enamel paint, complete all as specified and as directed. |
| 30 | Material and labour for preparation of new steel surfaces of any description, over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer, complete all as specified and directed. |
| 31 | Material and labour for preparation of old steel surfaces of any description, over 10 cm in width or girth and applying two coats of synthetic enamel paint, complete all as specified and directed. |
| 32 | S&F Sheet glass 4.00 mm thick ordinary quality and glazing with rubber packing in square n exceeding 0.5 sqm in each plane after hacking out old broken glass( any thickness,size,quality or description) from wooden frames or stone,concrete or brick surrounds, glazed with putty or fixed with beads, complete all as specified and directed. |
| 33 | S&F Sheet glass 4.00 mm thick ordinary quality and glazing with rubber packing in square exceeding 0.5 sqm in each plane after hacking out old broken glass (any thickness,size,quality or description) from wooden frames or stone,concrete or brick surrounds, glazed with putty or fixed with beads, complete all as specified and directed. |
| 34 | M&L for butyl & bitumen Based flashing tapes/strips 100 mm wide are cold applied self-adhesive tapes with one side bitumen adhesive protected by release film and other side is reinforced aluminium foil to prevent leakages, fill cracks & joints for metal, cement asbestos, fiber, plastic, vinyl etc., complete all as specified and as directed. |
| 35 | Supply and fix in repairs stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40 mm as in doors and windows with necessary nuts and bolts/ fillets, complete all as specified and directed. |
| 36 | Supply and fix in repair anodised aluminium frame three track for window, anodised aluminium window, sliding type shutters, sliding on two way aluminium channel, without sash bars, sliding on separate track, made out of aluminium section weighing not less than 0.55 Kg/RM and necessary jointing cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, fittings such as suitable anodised aluminium locking type handle etc and fixing of 4.00 mm thick tinted glass, complete all as specified and directed. |
| 37 | Supply and Fix in repairs Hand Shower (Health Faucet) with 8 mm bore, 1.2 Metre long PVC tube and wall hook with plastic body, all as per Cat No ALD-563 of Make “Jaquar” or equivalent Model of Make “Marc”/”Kohler\\"/ \\"Grohe”, complete all as specified and directed. |
| 38 | Supply and Fix in repairs PVC connections 15 mm size with PTMT nuts of length 450 mm, complete all as specified and directed. |
| 39 | Supply and Fix in repairs PVC collapsible waste pipe (31/32 x 800) mm all as pe Cat No.3272 of Make Prayag or equivalent model of Make Polytuff/Shakti, complete all as specified and directed. |
| 40 | Supply and Fix in repairs pillar taps, cast copper alloy, with capstan heads, fancy type, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nuts, screwed for iron pipe, 15 mm bore, complete all as specified and directed. |
| 41 | Supply and Fix in repairs bib taps cast copper alloy, chromium plated, with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule, 15 mm bore and fixed, complete all as specified and directed. |
| 42 | Supply and fix in repairs Vitreous China squatting pan, 'Orissa' pattern, size 580 x 440 mm white with integral foot rest and 'P' or 'S' trap, including provision of lime concrete bedding, connection to trap and flushing pipe etc complete (excluding flushing cistern and flush pipe) finishing with PCC gap between surface and new WC, complete all as specified and as directed. |
| 43 | Supply and Fix in repairs flush pipe of polyethylene of low or high density or PVC 32 mm dia, for low level cistern, complete all as specified and directed. |
| 44 | Supply and Fix in repair PVC valve less syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle, of capacity 10 Litres, including brackets, flush pipe, complete all as specified and directed. |
| 45 | Supply and fixing 500 litres capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part – I , including ball valve high pressure of PTMT (Minimum weight 210 gms) with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe, 20 mm bore and fixed and including dismantling existing water tanks exc. 250 but not exc.500 litres capacity and removing to store, complete all as specified and directed. |
| 46 | Supply and Fix in repairs, ball valves high pressure of PTMT (Minimum weight 210 gms) with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe, 20 mm bore and fixed, complete all as specified and directed. |
| 47 | Supply and fix in repairs Vitreous China urinals, half stall type (back or corner wall type) with grating and union for discharge pipe and waste pipe (excluding flushing cistern) complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, flush pipe, grating and Union for discharge pipe, complete all as specified and as directed. |
| 48 | Demolition of existing cement concrete of any type in ground floor and pavings, not exceeding 15 Cm thickness, complete all as specified and directed. |
| 49 | Materials and Labour for 100 mm thick plain cement concrete (1:4:8) type D2 using 40 mm graded aggregate as in sub base in floor/paving/ hardstanding, complete all as specified and directed. |
| 50 | Supply and fixing aluminium composit pannel (ACP) sheet 6 mm thickness as approved by Engr-in-Charge, in apporoved color and finish for aluminium partition and similar work, complete all as specified and directed. |
| 51 | Supply and fixing in repair Powder coated aluminium (minimum thickness of powder coating 50 micron) work for partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading and rubber for glazing/ paneling, C.P. brass/ stainless steel screws, including taking down of existing partiation with partical board etc complete all as specified and directed. Materials and Labour for rendering 8 mm thick, cement plaster, in cement mortar (1:4) mixed with water proofing compound as per manufactures instructions over and including 12 mm thick backing coat in cement mortar (1:4) on fair faces of brick work or concrete surface in walls, complete all as specified and directed.Note: - (Water proofing compound will be measured and paid separately) Please Enable Macros to View BoQ information |
