|
| 1 | Demolition of brick work or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins,arches, pillars,etc. but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed. |
| 2 | M&L for brick work with old size full brick subclass ‘B’ burnt clay bricks, straight or curved on plan exc 6m mean radius, built in CM (1:6) complete all as specified and directed. |
| 3 | M&L for walling of random rubble masonary, well bonded, bedded and solidly hearted, brought upto courses, built in cement mortar (1:6) complete all as specified and directed.Note :- Only quantity of PCC bond stone to be deducted from quantity of random rubble masonary. |
| 4 | Description same all as item No. 03 above but except stone complete all as specified and directed. Note :- Old retreived serviceable stone under demolition item shall be used. |
| 5 | Extra over stone walling for hammer dressing with maximum depression on face from straight edge held against the dressed surfacae not exceeding 40mm to face stone for Lime or sand stone and dressing of face beds and joints, as specified of random rubble walling, uncoursed or brought upto courses complete all as specified and directed. |
| 6 | M&L for raised pointing in cement mortar (1:4) to random rubble or polygonal rubble masonary uncoursed or brought upto course complete all as specified and directed. |
| 7 | S&F Powder Coated aodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified and directed. (minimum thickness of powder coating 50 micron) |
| 8 | S&F Powder coated anodised aluminium window and ventilator shutters,fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified and directed. (Thickness or powder coating not less than 50 micron). |
| 9 | S&F 4.8 mm thick plain or tinted glass, ordinary quality including rubber gasket for packing and fixed to aluminium Ventilator/window including necessary cutting / moulding and chamfering of edges for service window/counters complete all as specified and directed. |
| 10 | S & F Stainless steel wire cloth of 0.36 mm nominal dia of wire and average width of aperture 1.40 mm & fixed with tacks of stainless steel wire staples,etc complete all as specified and as directed. |
| 11 | M&L for Aluminium Composite Panels (ACP) of any colour of for fixing in shutter/partition with all other necessary accessories for fixing complete all as specified and directed. |
| 12 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and removing rubbish off the premises complete all as specified and directed. |
| 13 | M&L for glazed ceramic coloured tiles(Matt/Gloss Finish) of size not less than 450x300x7 mm thick as on vertical surfaces such as wall set and jointed in neat cement slurry and pointed with coloured cement to match over 10 mm thick backing coat on fair faces of brick work in CM 1:4 complete all as specified and directed. Note: Pattern/Texture and finish of wall Tile as approved. |
| 14 | M& L for Non - skid coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.18 sqm,as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over and including 15 mm thick screed bed in cement and sand mortar 1:6 complete all as specified and directed. |
| 15 | M&L for scratch & Joint free Glazed(Porcelain) Vitrified Tiles(GVT)/Polished Glazed Vitrified Tiles(PGVT) 9mm-10mm thick (square or rectangular) area of each tile exceeding 0.18sqm but not exceeding 0.36 sqm ie size 600x600mm as in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed or bedding layer in CM 1:6 complete all as specified and directed. Note : 1.Size and pattern/texture of GVT(Matt Finish)/PGVT(Glossy Finish) as approved. 2.Glazed Coating on GVT/PGVT not less than 1mm. |
| 16 | All as per Item No.15 above but 10 mm thick backing coat on fair faces of brick work in CM 1:4 in skirting complete all as specified and directed. |
| 17 | Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc complete all as specified and directed. |
| 18 | S&F 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc.of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed. |
| 19 | M&L for chequered cement concrete tiles, with grey cement and pigment of size 30cmx30cmx3 cm thick set and jointed and pointed in neat cement slurry in floors over and including 20mm thick screed bed in cement mortar (1:6) complete all as specified and as directed. |
| 20 | Demolition of cement Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) including removal of rubbish out side MOD land complete all as specified and directed. |
| 21 | M&L for 25 mm thick PCC (1:2:4) type B0, (using 12.5 mm graded stone agg) including finishing surface of concrete topping even and rough complete all as specified and directed. |
| 22 | M&L for 75 mm thick PCC (1:4:8) type D2, (using 40 mm graded stone agg) as in sub base of floor complete all as specified and directed. |
| 23 | Taking down cement plaster on brick or stone wall surfaces including glazed tiles wherever exists including raking out joints, hacking for key and scrubbing down with water etc and removing unseviceable materials out side MoD land distance n exc 1.5 km complete all as specified and as directed. |
| 24 | M&L for 10 mm thick plastering on brick or contrete surfaces, in CM (1:6), surface finished even and smooth without using extra cement complete all as specified and directed. |
| 25 | M&L for 15 mm thick plastering on other than fair faces of brick or contrete surfaces, in CM (1:4), using water proofing liquid compound as per manufacturer's instruction surface finished even and smooth without using extra cement complete all as specified and directed. |
| 26 | M&L preparation of newly plastered surface of external wall by application of 1 mm thick wall care putty to remove the dent and to make the surface even and smooth by grinding or rubbing with sand paper and applying two or more coats of 100% premium acrylic emulsion paint and including priming coat of exterior primer applied @ 0.90 ltr/10sqm complete all as specified and directed.(Putty shall be measured and paid separately.) |
| 27 | M&L preparation of newly plastered surface of internal wall by application of 1 mm thick wall care putty to remove the dent and to make the surface even and smooth by grinding or rubbing with sand paper and applying two coats of acrylic distemper over a coat of primer using roller complete all as specified and directed.(Putty shall be measured and paid separately.) |
| 28 | M&L for 1 mm thick acrylic/water proofing wall putty and surface finished even and smooth with sand paper complete all as specified and directed. |
| 29 | Dismantling of posts or struts (wood, steel or R.C.C.) any section, including taking out embedded portion from natural ground and making good disturbed ground complete all as specified and directed. |
| 30 | Excavating in post holes (or similar holes) in hard/ dense soil, each n exc 0.5 cum, getting out and removing surplus soil to a distance n.exc 50 m and making good surface complete all as specified and directed. |
| 31 | M&L for PCC (1:2:4) type B2 (using 40mm graded stone agg) as in foundation, embedding of post etc complete all as specified and directed. |
| 32 | Dismantling of fencing wire mesh, any type complete all as specified and directed. |
| 33 | Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provission of binding wire complete all as specified and directed. |
| 34 | Supply only Chain link MS galvanisd fencing, anysize or type complete all as specified and directed. |
| 35 | S&F galvanised, 2 strand, steel barbed wire 2.24 mm dia barbed with 2 mm dia barbs at 75 mm spacings and straining and fixing to any type of standard rails straining bolts , including,securing or tying at crossings with and Provision of galvanised mild steel wire, staples or steel pins etc. as directed ( each line wire to be measured) complete all as specified and directed. |
| 36 | S&F 11 to 15 mm dia of neck mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n exc 5cm long complete all as specified and directed. Please Enable Macros to View BoQ information |
| 37 | S&F 11 to 15 mm dia of neck mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n exc 5cm long complete all as specified and directed. Please Enable Macros to View BoQ information |
