|
| 1 | Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge. As per DSR vol-2 SI.No. 15.3( page no.220) |
| 2 | Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.. As per DSR vol-2 SI.No. 15.7.4( page no.220) |
| 3 | Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead :: As per DSR vol-2 SI.No. 15.12.1( page no.221) |
| 4 | Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.: As per DSR vol-2 SI.No. 15.23.1( page no.222) |
| 5 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil. As per DSR vol-1 SI.No. 2.8.1( page no.87) |
| 6 | Excavating trenches of required width for pipes, cables, etc, including excavation for sockets, depth upto 1.5 m, including getting out the excavated materials, returning the soil as required in layers not exceeding 20 cm in depth, including consolidating each deposited layers by ramming, watering etc., stacking serviceable material for measurements and disposal of unserviceable material as directed, within a lead of 50 m : Ordinary rock : Pipes, cables etc. not exceeding 80 mm diaAs per DSR vol-1 SI.No. 2.13.1.1 ( page no.88) |
| 7 | Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete. as per SI.No. 2.25 (a) |
| 8 | Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. as per SI no 2.27 |
| 9 | Supplying chemical emulsion in sealed containers including delivery and injecting chemichal complete as specified With and depth undar earth floor 5 litre/sqm of Chlorpyriphos/Lindane E.C. 20% with 1%concentration as per SI.No. 2.34.1 page no 91 |
| 10 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-lll) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) As per SI no. 4.1.8 |
| 11 | Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone ) finished with floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. 40 mm thick floor 20 mm nominal size stone aggregate. As SI No. 11.3.1 |
| 12 | Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75 mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.As per DSR vol-1 SI.No. 4.17 ( page no.101) |
| 13 | Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing:.1:2:4 (1 Cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) As per DSR vol-1 SI.No. 4.2.3 ( page no.97) |
| 14 | Providing and laying damp-proof course 40 mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-lIl) derived from natural sources : 4 graded stone aggregate 12.5 mm nominal size derived from natural sources) As per SI No.- 4.10 |
| 15 | Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7 kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil. as per SI-4.13 Centering and shuttering including strutting, propping etc. and removal of form for all heights : |
| 16 | Foundations, footings, bases of columns, etc. for mass concrete. As per DSR vol-1 SI.No. 5.9.1( page no.107) |
| 17 | Columns, Pillars, Piers, Abutments, Posts and Struts. As per DSR vol-1 SI.No. 5.9.6( page no.107) |
| 18 | Stairs, (excluding landings) except spiral-staircases As per DSR vol-1 SI.No. 5.9.7 ( page no.107) |
| 19 | Lintels, beams, plinth beams, girders, bressumers and cantilevers. As per DSR vol-1 SI.No. 5.9.5( page no.107) |
| 20 | Suspended floors, roofs, landings, balconies and access platform. As per DSR vol-1 SI.No. 5.9.3 ( page no.107) |
| 21 | Edges of slabs and breaks in floors and walls Under 20 cm wide.As per DSR vol-1 SI.No. 5.9.16.1 (page no.107) |
| 22 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement All work up to plinth level 1:1.5:3 (1 cement : 1.5 coarse sand (zone-lll) derived from natural sources:3 graded stone aggregate 20 mm nominal size derived from natural sources).As per DSR vol-1 SI.No. 5.1.2 (page no.105) |
| 23 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). As per DSR vol-1 SI.No. 5.2.2 (page no.105) |
| 24 | Reinforced cement concrete work in beams, suspended floors, roof having slope upto 15 degree, landings, balconies, shelves, chajjas, lintels, bands, staircases and spiral staircases etc. above plinth level up to floor V level, excluding the cost of centering, shuttering, finishing and reinforcement : in :1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)as per SI No. 5.3 |
| 25 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more. As per DSR vol-1 SI.No. 5.22.6/5.22.6A ( page no.110) |
| 26 | Brick work with common burnt clay modular bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand) As per DSR vol-1 SI.No. 6.2.1 ( page no.118) |
| 27 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:4 (1 cement : 4 coarse sand). As per DSR vol-1 SI.No. 6.4.1 ( page no.118) |
| 28 | Brick edging 7cm wide 11.4 cm deep to plinth protection with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 including grouting with cement mortar 1:4 (1 cement : 4 fine sand). As per DSR vol-1 SI.No. 6.44 ( page no.121) |
| 29 | Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators, side /top /centre hung, with beading and all members such as F7D,F4B, K11 B and K12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, priming coat of approved steel primer, but excluding the cost of other fittings,glass panes complete all as per approved design, (sectional weight of only steel members shall be measured for payment). as per SI no. 10.11.1 |
| 30 | Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer in-charge:as per SI no. 10.14.1( page no 171 |
| 31 | Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer G.I. pipes.As per DSR vol-1 SI.No. 10.26.3 ( page no.172) |
| 32 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to steel windows by welding. As per DSR vol-1 SI.No. 9.48 ( page no.141) |
| 33 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws:As per DSR vol-1 SI.No. 9.21.1 (page no.139) |
| 34 | Providing and fixing nickel plated M.S. pipe curtain rods with nickel plated brackets : SI-9.47 (page no.141) |
| 35 | Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors,windows and clerestory windows with hinges and necessary screws :9.27.1 35 mm thick shutters 9.27.1.1 with ISI marked M.S. pressed butt hinges bright finished of required size9.27.1.1.1 Second class teak wood.As per DSR vol-1 SI.No. 9.27.1 ( page no.139) |
| 36 | Providing and fixing glass panes with putty and glazing clips in steel doors, windows, clerestory, all complete with 5.5 mm thick glass panes. As per DSR vol-1 SI.No. 10.30.1 ( page no.173) |
| 37 | Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete :as per IS 1378) . As per DSR vol-1 SI.No. 9.74 (page no.144)SI.No. 9.74.1- 250 x 10 mm. |
| 38 | Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete :as per IS 1378) . As per DSR vol-1 SI.No. 9.74 (page no.144)SI.No. 9.74.3- 150 x 10 mm. |
| 39 | Providing and fixing bright finished brass door latch with necessary screws etc. complete :As per DSR vol-1 SI.No. 9.75 (page no.144)SI.No. 9.75.1- 300x16x5 mm |
| 40 | Providing and fixing bright finished brass door latch with necessary screws etc. complete :As per DSR vol-1 SI.No. 9.75 (page no.144)SI.No. 9.75.2- 250x16x5 mm |
| 41 | Providing and fixing bright finished brass handles with screws etc. complete: As per dsr 9.81 ( page no.145)SI.No. 9.81.1- 125 mm |
| 42 | Providing and fixing bright finished brass handles with screws etc. complete: As per dsr 9.81 ( page no.145)SI.No. 9.81.2- 100 mm |
| 43 | Providing and fixing 150 mm bright finished floor brass door stopper with rubber cushion, necessary brass screws etc. to suit shutter thickness complete. As per SI No- 9.82 |
| 44 | Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. 1 mm thick . SI 9.127.2 |
| 45 | Providing & laying rectified glazed ceramic floor tiles (make Somany or Orientbell) of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality confirming to IS:15622, of approved make, in colours white, ivory, grey, fume red brown, laid on 20 mm thick cement mortar 1:4 ( 1 cement: 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/sqm including grounting the joints with white cement and matching pigmrnts etc., complete as per SI no. 11.39 |
| 46 | Providing and fixing Ist quality ceramic glazed wall tiles (make Somany or Orientbell) conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. complete as per SI no. 8.31 |
| 47 | Providing and laying Vitrified tiles (make Somany or Orientbell) in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. as per SI no. 11.41.1 PAGE -180) |
| 48 | Providing and laying Vitrified tiles (make Somany or Orientbell)in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete.As SI No-11.46.1 ( page no.178) |
| 49 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels.As SI No-8.2.2 ( page no.128) Granite stone slab of colour black, Cherry/Ruby red. Area of slab over 0.50 sqm |
| 50 | Granite stone slab of all colour and texture except black, Cherry/Ruby red. Area of slab over 0.50 sqm |
| 51 | Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.. As SI No-8.3 ( page no.128) Granite work |
| 52 | Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete. As SI No-8.5 ( page no.128) Granite work |
| 53 | 12 mm thick cement plaster of mix 1:4 ( 1 cement & 4 course sand ) as per 13.4.1( page no.200) |
| 54 | Painting with synthetic enamel paint of approved brand and manufacture (Make-Asian/Nerolac/Berger) of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture as per Sl no. -13.62.1( page no.203) |
| 55 | Providing 10 mm thick plaster of Paris (gypsum anhydrous) ceiling up to a height of 5 m above floor level, over first class kail wood strips 25x6 mm with 10 mm gap in between and reinforced with rabbit wire mesh fixed to wooden frame (frame work to be paid separately) Flat surfaces: . As per Sl no. -12.31.1 (page no.189) |
| 56 | Distempering with 1st quality acrylic distemper (ready mixed) (Make-Asian/Indigo/Shalimar) having VOC content less than 50 gram/litre, of approved manufacturer and of required shade and colour all complete to achieve even shade and colour : New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litre as per Sl no. -13.41.1 ( page no.203) |
| 57 | Finishing walls with Acrylic Smooth exterior paint of required shade(Make-Asian/Nerolac/Berger): New work (Two or more coats applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm) as per Sl no. -13.46.1 |
| 58 | Providing and applying white cement based putty of average thickness 1 mm of approved brand and manufacturer,over the plasterd wall surface even and smooth surface as per Sl no. -13.80 |
| 59 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.110 mm diameter. As per SI- 12.41.2 |
| 60 | Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. As per SI-12.22 |
| 61 | Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge.(d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep.. -22.7 ( page no.303) |
| 62 | Providing and fixing water closet squatting pan (Indian type W.C. pan) (Make Cera/Hindware) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required (a) White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests. As per SI-17.1.1 ( page no.243) |
| 63 | Same as above but for European type W.C. pan (Make Cera/Hindware) with white plastic seat and lid.As per SI-17.2.1 (page no.243) |
| 64 | Providing and fixing wash basin (Make Cera/Hindware) with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require a) White Vitreous China Flat back wash basin size 550 x 400 mm with single 15 mm C.P. brass pillar tap.SI-17.7.4 (page no.244) |
| 65 | Providing and fixing PTMT Bottle Trap for Wash basin and sink. Bottle trap 31 mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 260 gms.SI-17.70.1 (page no.253) |
| 66 | Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backingSI-17.32 ( page no.247) S.N, 17.32.2 -Rectangular shape 453x357 mm |
| 67 | Providing and fixing PTMT grating of approved quality and colour. Circular type. As per dsr-2023 SI-17.32 (page no.266) S.N.- 17.32.2 100 mm nominal dia |
| 68 | Providing and fixing C.P. brass bib cock of approved quality (Make Cera/Hindware) conforming to IS:8931 :.SI-18.49.1 (page no.265) 15 mm nominal bore |
| 69 | Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour. Waste coupling 31 mm dia of 79 mm length and 62 mm breadth weighing not less than 45 gms :. SI-17.69.1 ( page no.253) |
| 70 | Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.(Make Cera/Hindware). SI-18.52 ( page no.266) |
| 71 | Providing and fixing Stainless Steel AISI 304 (18/8) kitchen sink as per I.S. 13983 with C.I. brackets and stainless steel plug 40 mm including painting of fittings and brackets, cutting and making good the walls wherever required Kitchen sink with drain board510 x 1040 mm bowl depth 250 mm, (Make Cera/Hindware). SI-17.10.1 (page no.247) |
| 72 | Providing and fixing flexible PVC waste pipe for sink or wash basin including PVC waste fittings complete.Semi rigid pipe. As per DSR-2023 SI-17.28.1 (page no.247)a) 32mm dia |
| 73 | Providing and fixing flexible PVC waste pipe for sink or wash basin including PVC waste fittings complete.Semi rigid pipe. As per DSR-2023 SI-17.28.1 (page no.247)b) 40mm dia |
| 74 | Providing and fixing soil, waste and vent pipes :- 75 mm diameter : As per DSR-2023 SI-17.35.2 (page no.247) |
| 75 | Providing and fixing PTMT soap Dish Holder having length of 138 mm, breadth 102 mm, height of 75 mm with concealed fitting arrangements, weighing not less than 106 gms. As per DSR-2023 SI-18.65 (page no.267) |
| 76 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank of approved brand and manufacture with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.As per DSR-2023 SI-18.48 (page no.265) |
| 77 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes (Make-Supreme/Astral/Prince), having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings and fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc.As per DSR-2023 SI-18.8 (page no.258) 15 mm dia nominal dia pipes |
| 78 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes (Make-Supreme/Astral/Prince), having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings and fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc.As per DSR-2023 SI-18.8 (page no.258) 25 mm dia nominal dia pipes |
| 79 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. As per DSR-2023 SI-12.41.1 (page no.190) 75 mm diameter |
| 80 | Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. As per DSR-2023 SI-23.3.1 (page no.308) 100 mm diameter |
| 81 | Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer in-charge. As per DSR-2023 SI-23.8 (page no.309) 20-40 mm stone ballast |
| 82 | Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer in-charge. As per DSR-2023 SI-23.6 (page no.309) 5-10 mm stone ballast |
| 83 | Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer -in-charge. As per DSR-2023 SI-23.7 (page no.309) 5-10 mm stone ballast |
| 84 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :As per DSR-2023 SI-18.17 (page no.259) 25 mm nominal bore |
| 85 | Providing & fixing C.P. brass angle valve for basin mixer and gyser points of approved quality conforming to IS 8931.As per DSR-2023 SI-18.53 (page no.266) a) 15mm nominal bore |
| 86 | Providing and fixing uplasticised PVC connection pipe with brass unions :.As per DSR-2023 SI-18.21 (page no.260) a) 30 cm length 15 mm nominal bore |
| 87 | Providing, laying and joining glazed stone ware pipes grade 'A' with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete.As per DSR-2023 SI-19.1 (page no.284) a) 100mm diameter |
| 88 | Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :As per DSR-2023 SI-19.6 (page no.285) a) 100mm diameter |
| 89 | Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :As per DSR-2023 SI-19.6 (page no.285) b) 150mm diameter |
| 90 | Providing & laying cement concrete 1:5:10 (1 cement :5 coarse sand :10 graded stone aggregate 40mm nominal size) alround S.W. Pipes including bed concrete as per standard design.As per DSR-2023 SI-19.2 (page no.284) a) 100mm diameter S.W. Pipe |
| 91 | Providing and fixing square-mouth S.W. gully trap grade‘A’ complete with C.I. grating, brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design. As per DSR-2023 SI-19.4.1 (page no.284)100x 100 mm size P type |
| 92 | Providing and fixing square-mouth S.W. gully trap grade‘A’ complete with C.I. grating, brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design. As per DSR-2023 SI-19.4.1 (page no.284)150 x 100 mm size P type |
| 93 | Constructing brick masonry manhole in cement mortar 1:4 (1 cement :4 coarse sand) RCC top slab with 1:2:4 mix (1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size), foundation concrete 1:4:8 mix (1 cement :4 coarse sand :8 graded stone aggregate 40mm nominal size) inside plastering 12mm thick with cement mortar 1:3 (1 cement :3 coarse sand) finished with floating coat fo neat cement and making channels in cement concrete 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20mm nminal size) finished with a floating coat of neat cement complete as per standard design. As per DSR-2023 SI-19.7.1 (page no.285) Inside size 90x80cms and 45cms deep including CI cover with frame (light duty) 455x610mm internal diamensions total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15kg).With FPS bricks of class designation 75 (i) For Sewer Line |
| 94 | Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 As per DSR-2023 SI-19.32 (page no.291) |
| 95 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.As per Electrical DSR-2022 SI-1.10 (page no.2) |
| 96 | Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. As per Electrical DSR-2022 SI-1.11 (page no.2) |
| 97 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.As per Electrical DSR-2022 SI-1.114 (page no.3) 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire |
| 98 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.As per Electrical DSR-2022 SI-1.114 (page no.3) 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire |
| 99 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.As per Electrical DSR-2022 SI-1.114 (page no.3) 2 X 4 sq. mm + 1 X 4 sq. mm earth wire |
| 100 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.As per Electrical DSR-2022 SI-1.114 (page no.3) 4 X 6 sq. mm + 2 X 6 sq. mm earth wire |
| 101 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.As per Electrical DSR-2022 SI-1.114 (page no.3) 4 X 10 sq. mm + 2 X 6 sq. mm earth wire |
| 102 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.As per Electrical DSR-2022 SI-1.31 (page no.7) |
| 103 | Supply and fixing of LED Tube Light with batten suitable for upto 1 X 22 watt LED tube light fitting including tube on Surface complete in all respect. - CAT-AAA |
| 104 | Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required. |
| 105 | Supplying of 1440 rpm heavy duty exhaust fan with bracket blades suitable to operate on 230V 50Hz, (Make- Havells/Crompton) AC Supply complete. 12\\" Sweep (300 mm) |
| 106 | Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections (Make- Havells/Crompton)but excluding modular plate etc. as required. |
| 107 | Supplying and fixing 3 pin, 5A ceiling rose on the existing junction box/ wooden block including connections etc. as required. |
| 108 | Supplying and fixing brass batten/angle holder including connection etc. as required. |
| 109 | Installation, Testing, Commissioning of wall bracket /ceiling fittings of all sizes and shapes containing upto two GLS/CFL/LED lamps per fitting, complete with all accessories including connections etc. as required. |
| 110 | Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required. |
| 111 | Numbering of ceiling fan/ exhaust fan/ fluorescent fittings as required. |
| 112 | Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required. |
| 113 | Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, \\"C\\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single pole |
| 114 | Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, \\"C\\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single pole and neutral |
| 115 | Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, \\"C\\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Double pole |
| 116 | Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required. |
| 117 | Supplying and making straight through joint with heat shrinkable kit including ferrules and other jointing materials for following size of PVC Insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. (i) 35 sq. mm 3-1/2 core |
| 118 | Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc, with charcoal/ coke and salt as required. |
| 119 | Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.l. nut, bolt, spring, washer etc, as required (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm) |
| 120 | Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required. |
| 121 | Providing and fixing H.T. danger notice plate of 250 mm X 200 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required. |
| 122 | Supply and fixing of 12 Watt to 15 Watt indoor Recess mounting LED Square Fitting for Armstrong Ceiling having Powder coated die cast aluminium housing with extended heat sink, diffuser of Polycarbonate material and driver set complete in all respect. CAT-AAA |
| 123 | Supplying and fixing of 240/415 V, 10 kA, \\"C\\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.(i) MCB 63 Amp. Three Pole 10kA |
| 124 | Supplying and fixing of 240/415 V, 10 kA, \\"C\\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.(ii) MCB 40 Amp. FP 10kA Please Enable Macros to View BoQ information |
