|
| 1 | Demolition of Brickwork or stone / boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and as directed. |
| 2 | Taking down cement plaster from brick or stone walls surfaces etc, including raking out joints, hacking for keys, scrubbing down with water, etc., complete all as specified and as directed. |
| 3 | Demolition of cement concrete (un-reinforced) in ground floors and pavings not exceeding 15 cm thickness (below or above ground ground level ) as in plinth protection/ hard standing/ floors/ path etc., complete all as specified and as directed. |
| 4 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing rubbish of the premises complete all as specified and as directed. |
| 5 | Taking down chowkat or frames with shutter (without taking off shutters from the frame) of area exc 1.5 sqm but n.exc 4 Sqm including making good the disturbed surface complete all as specified and as directed. |
| 6 | Taking down chowkat or frames with shutter (without taking off shutters from the frame) of area not exc 1.5 sqm including making good the disturbed surface complete all as specified and as directed. |
| 7 | M&L for Precast cement concrete (1:3:6) type C-1 using 20 mm graded crushed stone aggregate as in solid block masonry exc 10 cm in width and setting in cement mortar (1:6) complete all as specified and directed. |
| 8 | M&L for Precast cement concrete (1:3:6) type C-1 using 20 mm graded crushed stone aggregate as in solid block masonry not exc 10 cm in width and setting in cement mortar (1:4) complete all as specified and as directed. |
| 9 | M&L for rendering 15 mm thick in cement mortar (1:4) on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement including mixing with water proofing compound complete all as specified and as directed.(Note : water proofing shall be measured & paid separately). |
| 10 | M&L for rendering 10 mm thick in cement mortar (1:6) on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement all as specified and as directed. |
| 11 | M&L for rendering 5 mm thick in cement mortar (1:3) on fair faces of concrete ceiling surfaces finished even and smooth without using extra cement complete all as specified and as directed. |
| 12 | Supply only integral waterproofing compound, ISI marked, approved make complete all as specified & as directed. |
| 13 | M&L for 25mm thick Plain cement concrete (1:2:4) type B-0 using 12.5 mm graded crushed stone aggregate as in sub base to floor complete all as specified and as directed. |
| 14 | M&L for Non skid coloured ceramic tiles 7 to 8 mm thick, joint free, area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the tiles over & including screed bed 15 mm thick in CM (1:6) complete all as specified and as directed. |
| 15 | M&L for Non skid coloured ceramic tiles 7 to 8 mm thick, joint free, area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the tiles over & including screed bed 15 mm thick in CM (1:6) complete all as specified and as directed. |
| 16 | M&L for Non skid coloured ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm as in vertical surface / dado / skirting etc., set and jointed in neat cement slurry and pointed in coloured cement to match over & including backing coat 10mm thick in CM (1:4) complete all as specified and as directed. |
| 17 | M&L for Glazed ceramic coloured tiles of size 350 x 250 x 7mm/ 450x 350 x 7mm thick on vertical surfaces such as dados and risers to step etc., set and jointed in neat cement slurry and pointed in coloured cement to match the tiles over & including backing coat 10mm thick in CM (1:4) complete all as specified and as directed. |
| 18 | M&L for Sadarhalli stone slab 18-20mm thick as in flooring, steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of slab over & including screed bed 15 mm thick in CM (1:4) and rounding to edges complete all as specified and as directed. |
| 19 | M&L for Sadarhalli stone slab 18-20mm thick for skirting, riser, dado and like jointing in CM (1:3) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of slab including backing coat 10 mm thick in CM (1:3) complete all as specified and as directed. |
| 20 | S&F Factory made pressed steel frames of profile size 125x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc., made of mild steel sheet of 1.25 mm thickness, complete as specified & as directed |
| 21 | S &F Second class hard wood factory made glazed and skeleton shutter 35 mm thick, open rebated and prepared to receive glass, guage etc., edge of framing plain chamfered or rounded fitted with cut and mitred beads for securing guage etc., size of members of shutter as specified in SSR Part I Section 8 clause 8.24 (a) supplied and fitted to chowkats complete all as specified & as directed |
| 22 | S&F Flush shutters 30mm thick, solid core construction, with block coard core & plywood face panels commercial type on both side conforming to IS 2202 (Part- I), including internal liping beading all round, fixed as in Door shutter,Cup board shutter & Kitchen rack complete all as specified & as directed. |
| 23 | S&F in repairs stainless steel wire cloth, 0.24mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples including supply & fix second class hard wooden fillet, wrought, cross sectional area exceeding 3 Sqcm but n.exc 6 Sqcm fixed with nails complete all as specified and as directed. |
| 24 | S&F Powder coated aluminium sliding window, three track, frame & two glazed shutters and one wiremesh /skeleton shutter with the following specifications complete all as specified and as directed :-(i) Aluminium frame section 116x36.50x1.80mm.(ii) Aluminium shutter glazed/skeleton section 50x20x1.50mm thick.(iii) Aluminium grill size 50mmx50mm and 4 to 5mm thick bars. (iv) Lugs / hold fast in walls incl PCC (1:3:6) type C-1 block including making good the distributed surfaces (v) Glass 4mm thick ordinary quality and fixed with rubber gasket for glazed shutter etc.(vi) Stainless steel wire mesh 0.36mm nominal dia & avg width of aperature 1.14mm and fixed with rubber gasket for gauzed shutter etc.(vii) Aluminium disc /bow hanle and locking system complete |
| 25 | S&F Powder coated anodised aluminium window and ventilator shutter, side hung type without sash bar, aluminium sections weighing 0.55kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long -1 no, aluminium hinge type B-21 100mm long-2 no, suitable handle -1 no complete all as specified & as directed. |
| 26 | S&F Figured glass, pinhead glass 5mm thick in square or rectangular, glazing with oil putty in squares n. exc 0.5 sq. m in each pane complete all as specified & as directed. |
| 27 | S & F Sheet glass 5.5 mm thick, frosted/obscured quality and glazing with UPVC beading in square/rectangular n.exc 0.50 sqm in each panes complete all as specified and as directed. |
| 28 | S & F in repairs rotational moulded polythylene water storage tank 1000 litres capacity (cylindrical vertical with close top) triple layer, white colour inside and outside with top cover including adapter, PTMT float valve high pressure 25 mm dia pipe with polythene float, fixture hoisted and fixed in position and making necessary connection and testing complete all as specified & as directed. |
| 29 | Taking up or down steel tubing 25mm dia galvanised along with fittings complete all as specified & as directed. |
| 30 | Taking up or down steel tubing 20mm dia galvanised along with fittings complete all as specified & as directed. |
| 31 | S&F CPVC Pipe 25 mm outer dia (ISI Marked) SDR II & plain CPVC SDR II fittings fixed on wall, celing or floors complete all as specified & as directed. |
| 32 | S&F CPVC Pipe 20 mm outer dia (ISI Marked) SDR II & plain CPVC SDR II fittings fixed on wall, celing or floors complete all as specified & as directed. |
| 33 | S & F in repairs Health faucet (ABS) Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and as directed. |
| 34 | S & F in repair 15mm dia bib cock 2 way double handle with flange, cast copper alloy chromium plated, screwed down, suitable for 15mm dia iron pipe complete all as specified and as directed. |
| 35 | S&F in repair 15mm dia stop valves/angle valve cast copper alloy chromium plated fancy type with long shank and cup, screwed down to iron pipe 15 mm dia complete all as specified and directed |
| 36 | S&F Glass Corner Shelf with 5.50mm thick glass 300mm, brass CP 2Nos guards including fixed with screws on wall complete all as specified & as directed. |
| 37 | S & F in repairs wall mixer for mixing hot and cold water, brass chromium plated, screwed down with provision of over head shower and cock for iron pipe 15mm bore and fixed complete all as specified and as directed. |
| 38 | S & F in repairs Vitreous china wash down water closet pan, pedestal pattern, white, including connection to outgoing drain and 32mm dia flush pipe, flushing pipe, anti syphonic pipe with following accessories including making good damaged / disturbed surfaces complete all as specified and as directed :-(i) PVC seat and cover closed pattern with flat bottom white and MS chromium plated hinging device(ii) Low level PVC Flushing cistern 10 ltr capacity, PVC valveless, syphonic action type, low level, white, with inlet, ball valve, float and handle including brackets(iii) PVC connection pipe 15 mm dia 600 mm long with PTMT nuts |
| 39 | S&F in repair Vitreous China Wash hand basin, white flat back of size 550x400 mm including a pair of mild steel angle iron brackets duly painted, erected/embeded in wall including cutting hole and pinning in ends making good disturbed portion using cement mortar (1:3) with following accessories complete all as specified & as directed :-(i) Pillar taps, brass, with capston heads, fancy type, chromium plated.(ii) Waste coupling 32mm dia brass chromium plated suitable for wash hand basins with LDPE PVC waste pipe.(iii) PVC connection 15 mm dia 450 mm longwith PTMT nuts |
| 40 | S&F in repair Looking mirror bevelled edge of size 600x450 mm of selected quality glass, mounted on 6 mm thick AC building board or commercial plywood and fixed on wall with wooden plugs with chromium plated brass screws and cup washers complete all as specified and as directed. |
| 41 | Supply and fixing in repair Bib tap cast copper alloy with crutch or butter fly handle screwed down screwed for Iron Pipe 15mm dia or brass ferrule and fixed complete all as specified and as directed. |
| 42 | S&F in repairs Aluminium anodised tubular towel rail, 20mm dia ‘D’ shaped type, 60CM long between flanges complete all as specified and as directed. |
| 43 | S&F in repairs Soap dish 150mm, stainless steel fixed to wall with chromium plated brass screws complete all as specified and as directed. |
| 44 | S&F Toilet Pepar holder with flat recessed type, stainless steel made complete all as specified and as directed. |
| 45 | S & K in repairs PVC (SWR) floor trap 75mm diaoutlet, plain with grating including jointing with solvent cement etc complete all as specified and as directed. |
| 46 | S&F in repairs PVC (SWR) pipes 110mm dia, single socketed in any length with rubber joints fixed to walls etc complete all as specified and as directed. |
| 47 | S&F in repair PVC (SWR) pipes 75mm dia single socketed in any length with rubber joints fixed to walls etc complete all as specified and as directed. |
| 48 | S&F PVC (SWR) bends 110mm dia any radius complete all as specified and as directed. |
| 49 | S&F PVC (SWR) bends 75 mm dia any radius complete all as specified and as directed. |
| 50 | S&F Solid PVC Door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, supplying & fixing in opening as per specification complete all as specified and as directed. |
| 51 | S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification complete all as specified and as directed. |
| 52 | S&F Butt hinges 75mm size, mild steel cold rolled, medium weight, complete all as specified and as directed. |
| 53 | S&F Aluminium, anodized barrel tower bolts 100mm long of extruded section complete all as specified and as directed. |
| 54 | S&F Aluminium anodized handles 100mm size, extruded section complete all as specified and as directed. |
| 55 | S&F in repair Aluminium anodised decorative type curtain rod 25mm dia including fancy finale caps cap etc., fixed to rod complete all as specified and directed |
| 56 | S&F in repairs brackets for decorative type curtain rod aluminium 25mm dia fixed to wall complete all as specified and as directed. |
| 57 | M&L for Plain cement concrete (1:2:4) type B1 using 20mm gradded crushed stone aggregate as in copings etc, including necessary form work as required at site, rounded or chamfered on edges complete all as specified and as directed. |
| 58 | S&F Medium Density Fiber board (MDF Board) 19 mm thick both side finished, cut to size & fixed in wardrobes, number of compartments & drawers complete all as specified and as directed. |
| 59 | S&F in repair Magnetic catcher stainless steel body & striking plate including fixing on shutter & frame complete all as specified & as directed. |
| 60 | S&F continuous (Piano) hinges 40mm width of flaps (when open) mild steel bright finish or electrogalvanised all as specified and as directed. |
| 61 | S & F in repairs shower rose 125mm dia brass chromium plated with swivel joints, fixed to iron pipe 15mm dia complete all as specified and as directed. |
| 62 | M&L for Preparation of newly plastered surfaces of wall and finishing all as per following specification complete all as specified and as directed. :-(i) Applying 1mm thick wall care putty finished to smooth surfaces.(ii) Applying a coat of alkali resitant primer.(iii) Applying two coats of Acrylic emulsion distemper. |
| 63 | M&L for complete removal of existing treatment of old plastered surfaces of wall till appearance original plastered surface using wire brush, washing etc complete and finishing all as per following specification complete all as specified and as directed :-(i) Applying 1mm thick wall care putty finished to smooth surfaces.(ii) Applying a coat of alkali resitant primer. (iii) Applying two coats of Acrylic emulsion distemper. |
| 64 | M & L for Preparation of new plastered surfaces and Applying two or more coats of 100% premium acrylic exterior weather proof emulsion paint having VOC less than 50gm/litre and UV resisitance as per IS 15489:2004, alkali & fungal resistance dirt resistance of required shade (company depot tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior grade primer applied @ 0.90 litre/ 10 sqm complete all as specified & as directed. |
| 65 | M & L for Complete removal of existing treatment of old plastered surfaces of wall till appearance original plastered surface using wire brush, washing etc., and applying two or more coats of 100% premium acrylic exterior emulsion weather proof paint having VOC less than 50gm/litre and UV resisitance as per IS 15489:2004, alkali & fungal resistance dirt resistance exterior paint of required shade (company depot tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior grade primer applied @ 0.90 litre/ 10 sqm complete all as specified & as directed. |
| 66 | M&L for Preparation of newly plastered ceiling surface and applying three coats of white wash complete all as specified & as directed. |
| 67 | M & L for Preparation of Old decorated / treated ceiling surface and applying one coat of white wash complete all as specified and as directed. |
| 68 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed. |
| 69 | M&L for Rolled mild steel in framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared to be hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive or steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing, conforming to Fe-410-W(Gde-E-250) Quality-B complete all as specified and as directed. |
| 70 | M&L for Preparation of new or previously untreated steel and iron surfaces of any description, over 10 cm in width or girth, not otherwise described and applying two coats of synthetic enemel paint over a coat of red oxide primer complete all as specified and as directed. |
| 71 | M&L for Stainless steel Grade 304 as in railing made of hollow tubes, channels, plates etc., including welding, grinding buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete , including fixing the railing with necessary accessories & stainless steel dash fastners,stainless steel bolts etc.of required size on the top floor or the side of waist slab with suitable arrangement complete all as specified & as directed. |
| 72 | M&L for PCC (1:3:6) type C1 using 20mm graded crushed stone aggregate, finished even and fair without using extra cement.as in 75 mm thick plinth protection finished fair & even including joints filling with sealing compound grade A complete all as specified & as directed. |
| 73 | Demolition of cement concrete (un-reinforced) of any description and in any position not otherwise specifically provided for roof /chajja padding including water proofing memberane and removal of debris complete all as specified & as directed. |
| 74 | M&L for Rendering 10mm thick in CM (1:3) on RCC roof concrete surface finished even and smooth without using extra cement including mixing WPC complete all as specified & as directed. (Note : WPC will be measured and paid seprately). |
| 75 | M&L for water proofing treatment over RCC roof slab all as per following specification complete all as specified & as directed :- (i) Removing all loose gravel, dirt, oil, grease and foreign materials by jet or dry air, cleaning the surfaces mechanically or by grinding to make the surface smooth(ii) Applying compatible oil bound bitumen primer @ 0.40 Kg/Sqm (iii) Laying 3 mm thick APP modified water proofing membrane weighing not less than 3.8 kg/sqm reinforced with non woven polyester matt weighing not less than 150 gm /sqm having softening point not less than 140 centigrade, having tensile strength of 650N /sqm and 350 N/sqm in longitudinal and transverse directions respectively of the reinforced tearing strength of 180N by torch application with minimum 10cm side overlap and 15cm end lap.(iii) Applying solar reflective bituminious aluminium paint @ 0.10 Kg/Sqm.(iv) Pond test for 72 hours shall be carried out for dampness / leakage test. |
| 76 | M&L for Preparation of new or previously untreated wood or wooden based surfaces of any description, over 10 cm in width or girth, not otherwise described and applying two coats of synthetic enemel paint over a coat of pink primer complete all as specified & as directed. |
| 77 | S&F Butt hinges 100 mm mild steel cold rolled, medium weight complete all as specified & as directed. |
| 78 | S&F Aluminium alloy, anodised, sliding door bolt 300mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast- aluminium alloy and fixed all as specified & as directed. |
| 79 | Taking down copper/ aluminium point wiring(light, fan, socket or power) complete, including fittings and fixtures such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions seperately) and making good distrubed surfaces of wall, floors, etc complete all as specified & as directed. |
| 80 | M&L for Point wiring with PVC insulated FRLS unsheathed 1100 volts grade with multistranded copper conductor cable 1.5 sqmm single core conforming to IS-694 1990 with ISI marked (for phase ,neutral and earth) drawn in and including non metalic rigid PVC conduit medium grade with ISI mark of minimum 20mm dia with all conduit accessories Concealed including cutting / chases in wall /ceiling /fixed to roof /truss/columns etc and including factory made branded make embossed galavanised steel pressed terminal boxes alongwith suitable size modular cover plates & frames for fixing modular switches, sockets, regulators of suitable size modules and earth wire to be connected to common earth dolly complete all as specified and as directed for the following :- |
| 81 | One light / fan / bell point controlled by one 5 Amps switch one way |
| 82 | One light point controlled by one 5 Amps switch two way |
| 83 | One 3 pin socket point 5 Amp on independent board |
| 84 | One 3 pin socket point 5 Amp on same board with other switches. |
| 85 | M&L for Point wiring with PVC insulated FRLS unsheathed 1100 volts grade with multistranded copper conductor cable 2.5 sqmm single core conforming to IS-694 1990 with ISI marked (for phase ,neutral and earth) drawn in and including non metalic rigid PVC conduit medium grade with ISI mark of minimum 25mm dia with all conduit accessories Concealed including cutting / chases in wall /ceiling /fixed to roof /truss/columns etc and including factory made branded make embossed galavanised steel pressed terminal boxes alongwith suitable size modular cover plates & frames for fixing modular switches, sockets, of suitable size modules and earth wire to be connected to common earth dolly complete all as specified and as directed. |
| 86 | Supply and fix modular switch 1 way 6Amps,1 module, 240volts all as specified and as directed. |
| 87 | Supply and fix modular switch two way 6Amps,1 module 240volts all as specified and as directed. |
| 88 | Supply and fix modular switch 1 way 16Amps,1 module 240volts all as specified and as directed. |
| 89 | Supply and fix socket, 6Amps - 2/3 pin combined 2 modules, 240volts all as specified and as directed. |
| 90 | Supply and fix socket, 6A / 16Amps - 2/3 pin combined, 2 modules, 240volts all as specified and as directed. |
| 91 | Supply and fix modular fan Requlator, 120 Watts - 2 modules, 240volts all as specified and as directed. |
| 92 | Supply and fix modular Bell push 5 Amp, 240volts all as specified and as directed. |
| 93 | Supply and fix Ceiling rose surface bakelite 65x50mm, three terminals including PVC blocks all as specified and directed. |
| 94 | Supply and fix in repair Door bell electronic, multi music type, 230 volt AC all as specified and as directed. |
| 95 | S&F LED tube light fitting of 10 watts 6000K , 230 volt, with aluminium extruded channel powder coated with diffuser for glare free light with all fixing accessories such as 2 nos of PVC square/round boxes, screws, etc and connecting up with three core flexible copper conductor cable of size 24/0.20 sqmm complete all as specified and as directed. |
| 96 | S&F LED tube light fitting of 20 watts 6000K , 230 volt, with aluminium extruded channel powder coated with diffuser for glare free light complete with all fixing accessories such as 2 nos of PVC square/round boxes, screws, etc and connecting up with three core flexible copper conductor cable of size 24/0.20 sqmm complete all as specified and as directed. |
| 97 | Supply and fix Designer trendo wall light with Warm white/white LED luminare 12 Watt capacity with polymer diffuser complete with accessories suitable for armstrong/Grid ceiling, internally pre-wired and connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and as directed. |
| 98 | Supply and fix round shape down lighter 20 Watt capacity Warm white/white surface mounted type LED luminare with polymer diffuser complete with accessories suitable for armstrong/Grid ceiling with all accessories internally pre-wired and connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and as directed. |
| 99 | Supply and fixing LED street light fitting 35 watt capacity 230 Volts AC outdoor type with high pressure die cast aluminium housing and heat resistant with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics with IP 65/66 protection complete all as specified and as directed. |
| 100 | Supply and fixing post top lantern LED type 20 watt capacity, warm white 230 volt AC outdoor type with decorative post top for 360 degree indirect light IP 65 protection with impact and corrosion with driver and lamp including pole box complete all as specified and as directed. |
| 101 | M&L for PVC insulated 2 x1.5sqmm + 1x 1.5 sqmm earth wire single core copper conductor for connection of post top lantern to Pole Box with necessary PVC conduit & accessories complete all as specified and as directed. |
| 102 | Supply & fix in repair FRP junction box, weather proof of size 150 x 150 x 70 mm including single phase connector arrangement alongwith suitable clamps including MCB SP 5 Amps 10 KA rating, fixing with flat iron clamps, nuts and bolts complete all as specified and as directed. |
| 103 | Supply and fix in repair Rigid Non-metallic PVC conduit pipe of size 20 mm dia. exclusive of junction boxes but inclusive of all Tees,bends elbows,reducers, bell mouth tube end and fixing acessories such as couplers, lock nuts, saddles pipe hooks etc., and fixing to poles etc all as specified & as directed. |
| 104 | M & L for taking down ceiling fan 1200mm sweep, open the stator & removing defective copper winding wire and Re-winding of ceiling fan with appropriate size of copper enamelled wire including varnishing, heating with proper insulation complete and testing on completion and refixing back to its original position complete all as specified and as directed. |
| 105 | Supply and fixing ceiling fan 1200 mm sweep, with blades, down rods and accessories, 230 Volts,.Min air delivery 210 CFM with service value 6 BEE, Five star rated with brushless direct current (BLDC) motor complete all as specified and as directed. |
| 106 | Supply and fix in repair Sheet metal enclosure (ISI marked) distribution board TPN, 415 volts, 4 way horizontal type double door type, 200 Amps rated neutral copper bus bar for housing MCB and fixed and tested on completion complete all as specified & as directed. |
| 107 | Supply and fix in repair Vertical Sheet metal enclosure (ISI marked) Distribution board VTPN MCCB DB 415 volts, 8 way double door type, neutral copper bus bar for housing MCB and fixed and tested on completion complete all as specified & as directed. |
| 108 | S&F in repair Sheet metal enclosure (ISI marked) distribution board for 240 volts, SPN 8 way horizontal type, double door, single pole and neutral with 200 Amps rated neutral copper bus bar for housing MCB and fixed flush in wall surface, and tested on completion complete all as specified & as directed. |
| 109 | Supply and fix in repair MCB single pole 6 to 32 Amps 240 volts, C series, 10 kA rupturing capacity complete all as specified & as directed. |
| 110 | S & F RCBO single pole and neutral 40 Amps 240 volts, 30mA capacity for earth leakage short circuit and over load protection providing in DB complete all as specified & as directed. |
| 111 | Supply and fix in repairs RCCB Tripple pole & neutral, 40 to 63 Amps 415 volts, 30mA capacity for earth leakage Short Circuit and over load protection providing in DB complete all as specified & as directed. |
| 112 | S&F RCBO Four Pole MCCB 63 Amps, 50 HZ,415 V ,30 mA capacity for earth leakage Short Circuit and over load protection providing in DB complete all as specified & as directed. |
| 113 | S & F Exhaust fan 250 mm sweep made of sturdy Engineering plastic with self closing louvers and blades, 230 Volts, 50 Hz, 1200 RPM noiseless, copper winding complete all as specified and as directed. |
| 114 | Supply and fix in repairs Sub main wiring with 2 runs of 4 sqmm, single core, PVC insulated & unsheathed cable conforming to IS-694, 1100 volts with copper conductor multi stranded drawn in existing non metallic PVC grey conduit with all accessories such as tees, elbows, junction box, reducers etc as requied alongwith one run of 4 sqmm single core PVC insulated & unsheathed copper conductor as continuos earth wire dolly and connecting to existing main switch board / distribution board of each building / qtr as ordered and testing on completion complete all as specified and as directed. (Note : Three run of 4sqmm cable measured as one unit) |
| 115 | Supply and fix in repairs Sub main wiring with 2 runs of 6 sqmm, single core, PVC insulated & unsheathed cable conforming to IS-694, 1100 volts with copper conductor multi stranded drawn in existing non metallic PVC grey conduit with all accessories such as tees, elbows, junction box, reducers etc as requied alongwith one run of 6 sqmm single core PVC insulated & unsheathed copper conductor as continuos earth wire dolly and connecting to existing main switch board / distribution board of each building / qtr as ordered and testing on completion complete all as specified and as directed. (Note : Three run of 6sqmm cable measured as one unit) |
| 116 | Excavation in trenches in soft/loose soil, not exc 1.5 mtr wide and n exc 1.5 mtr in depth; for foundation, laying pipes / electric cables etc, and getting out complete all as specified & as directed. |
| 117 | Supply and spreading river sand to required width at bottom and top for L T cable cushioning complete all as specified & as directed. |
| 118 | Supply and lay bricks old size sub class B of size 230mmx 115mmx 75mm , laid at right angle on the cable for cable protection complete all as specified & as directed. |
| 119 | Returning, filling in, including spreading, leveling, watering and well ramming in layers not exc 25 cm thick soil complete all as specified & directed. |
| 120 | Removing excavated soil to a distance not exc. 50 mtr and depositing where directed at a level not exc 1.5 mtr above the starting point complete all as specified & as directed. |
| 121 | S&F Mild steel galvanized pipe 50mm dia. light grade for protection & passing of LT cable fixed to poles/walls/laid under floor/roads complete including fittings/clamps as required at site complete all as specified & as directed. |
| 122 | Supply & fixing in repairs XLPE insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cables 70 sqmm x 3.5 core ( heavy duty) with stranded aluminum conductor, 1100Volts grade, fixed on walls or laid in trenches with fixing acessories, testing and commissioning complete all as specified and as directed. |
| 123 | M&L for Earthing with galvanised steel earth plate electrode 60cm x 60cm x 6 mm thick buried directly in ground (earth pit depth not less than 2.25m deep below the ground level) with top edge of earth plate at a depth not less than 1.5m below ground level connected to earth using GI earth wire of 4 mm dia by means of of nuts, bolts and washer and check nuts of GI or steel as shown in electrical plate No.3 of MES SSR Part-I and connected to earth test point all as specified or indicated including testing on completion with and including 15mm bore light grade GI protection pipe 7.5 metre long for earth, PCC (1:2:4) pit with RCC (1:2:4) type B-1 cover 40mm thick reinforced with 8mm dia MS TMT bars @ 100mm both ways with lifting hooks made out of 6mm dia MS bars, watering arrangement with 20mm dia medium grade pipe, funnel, wire mesh, common salt chorcoal, necessary excavation and earth work in any type of soil complete all as specified & directed. Please Enable Macros to View BoQ information |
