Tender For Revised Dnit Providing Installing Testing Commissioning And Handing Over Of Hvac System For Setting Up Of Mother And Child Care Centre At Block K, Sector - 32A, Chandigarh. (Including 5 Years Operation, Running & Comprehensive Maintenance, Chandigarh-Chandigarh

TDR : 56030550

Tender Notice
BOQ

12 Days Left

Chandigarh , Chandigarh

Tender Brief : Tender For Revised Dnit Providing Installing Testing Commissioning And Handing Over Of Hvac System For Setting Up Of Mother And Child Care Centre At Block K, Sector - 32A, Chandigarh. (Including 5 Years Operation, Running & Comprehensive Maintenance

Document Fees
Refer document

EMD
₹ 1699769.0 /-

Tender Value
₹ 8.49 Crore /-

Submission Date
30-06-2026

Competition Type
Indian

Bidding Type
Tender

Need a Business Loan? Apply Now !


1	PART A
2	DESCRIPTION
3	EQUIPMENT
4	WATER COOLED SCREW CHILLING MACHINES WITH VFD
5	Supply, Installation, Testing and Commissioning of Water cooled screw type water chilling machine with VFD each having a capacity as given hereunder at chilled water inlet/outlet temperature of 12.22°C/6.7°C, Fouling Factor 0.0005 FPS and condenser water inlet/outlet temperature of 32.2°C/36.4°C Fouling Factor 0.001 FPS, suitable for operation on factory charged refrigerant R-134a for screw type machine each comprising of the following complete as per specifications and as required complete in all respect to the entire satisfaction of EIC.
6	Screw type compressor semi hermetic complete with automatic capacity control safety switches, forced feed lubrication system
7	The semi hermetic compressor should be mono/ twin type. Capacity control range of compressor shall be from min.25% to 100%
8	Suitable capacity squirrel cage induction motor with class 'B'/'H' insulation suitable for operation on 415 +- 10% volts,50Hz, A.C. supply.
9	1 No. suitable capacity Variable frequency drive for the above compressor motor complete with ammeter with CTs, over load protection, under voltage protection, protection against phase reversal & independent single phase preventers etc complete as required. with Active Harmonic Filters to achieve THDI & THDI not to exceed 5% at source
10	Necessary drive arrangement.
11	1 Set - Lubrication device consisting of automatic electric oil pump, oil cooler, head tank, oil strainer, and automatic pressure regulating valve, oil heater, oil heater thermal switch etc. as per specifications.
12	1 No. - Matching shell and tube water cooled condenser of M.S. shell and integrally finned copper tubes with Max. Pressure Drop of 6 mtrs with odd/even pass
13	1 No. - matching shell & tube flooded type chiller of MS shell and copper tubes with Max. Pressure Drop of 3 mtrs with odd/even pass
14	1 Lot - Refrigerant piping fittings, valves and accessories to inter connect compressor, condenser, chiller and expansion valve.
15	1 Set - Microprocessor based control panel complete with accessories as per specifications.
16	Lot - Refrigerant line accessories comprising of safety valves, angle valve, liquid line indications, liquid level control etc.
17	Lot - Water flow switches at outlet of condenser & chiller, water drain, air purge valves, thermometers and pressure gauges wherever required.
18	Lot - Suction line and chiller factory insulated with minimum 19mm thick polyvinyl nitrile rubber insulation complete as required.
19	Lot- Frame work for mounting the above condenser, chiller compressor and motor with base plate complete with anti-vibration pads/springs.
20	Lot- Initial/first charge of refrigerant gas & compressor oil.
21	Lot- RCC / Cement concrete foundation for the chilling unit.
22	Lot-Anti Vibration pads in foundation for chiller machine to avoid vibrations to the building
23	Lot - Coupling Connections for both condenser and chiller to avoid vibrations
24	Screw type chilling machine described above, as per specifications and complete in all respects for the operating parameters as given under.
25	The evaporator and condender shall have ASME Stamping
26	Chiller & Compressor should be of same make and machine shall be AHRI Certified.
27	Minimum COP should be 5.8 The NPLV of VFD chiller should not be more than 0.39 KW/TR. The IKW/TR should not be more than 0.66
28	Maximum IKW/ TR at operating conditions 0.66 KW/TR.
29	The price includes, loading/unloading and shipment till site Including Insurance Charges ,Unloading at site,RCC Foundation, placement of Chilling machine on the foundation, co-ordination during execution, rendering necessary guidance for execution, supervision, testing, commissioning and startup of above mentioned chiller. Radiographic Non Destructive Test for long seam welding of both evaporator and condenser shells shall be done and the test report of the same shall be verified during factory testing of chillers.
30	Chiller 220 TR (Actual Capacity) (2W+1S)
31	(Make: As per approved make list attached)
32	The Charges for above 220 TR x 1 no chiller got witness tested at AHRI certified test bed in OEM factory for 4 load points (100%, 75%, 50% & 25%)at the cost of the agency/ firm along with the Model & Serial No. of the Machine as per direction of EIC .The machine shall be accompanied with the 4 point test report duly certified by the OEM. No payment shall be released without the same .
33	Note : Vendor Shall Supply all chiller of same make at site, different brands are not allowed
34	Hot Water Generator
35	Supplying, installation, testing and commissioning of electrical HW generator equipped with sufficient number of electrical immersion heaters. The Hot Water Generator shall be of following capacity made of 8mm MS sheet and dish end made of 10mm MS having 16 gauge stainless steel lining with heaters arranged in banks and controlled by electronic Controller and Thermostats so that hot water is generated at 70 degree C with nominal variation including 75mm thick resin bonded fibre glass insulation of 24 kg/Cum density finished with 1.25mm thick aluminum sheet cladding including necessary electrical panel having suitable incoming and outgoing switchgears for heaters, automatic controls such as manual reset high temperature water outlet, step controller and recycling relay, 'ON' 'OFF' switch thermostats, pilot light, low water cutoff and other controls as per manufacturers recommendations including inlet and outlet connections for water as per specifications complete with pressure release valve, low level cut-out. Autovent sight-glass, foundation for Hot water generator as per specifications complete as required. All basic controls and terminals shall be located in an integral control cabinet factory wired and tested. The generator shall be suitable for 415 (+)/(-) 10% volts, 50 cycle, 3 phase power supply. The entire generator shall be factory assembled and tested at 350 PSI pressure.
36	The price includes loading/ unloading and shipment till site Including Insurance Charges ,Unloading at site,RCC Foundation, placement of HWG on the foundation, co-ordination during execution, rendering necessary guidance for execution, supervision, testing, commissioning and startup of above mentioned HWG.
37	300.0 KW Actual Capacity Hot water generator (with Multiple Bank (1 Working + 1 Standby)
38	(Make: As per approved make list attached)
39	Hot water generator (Monsoon Reheating)
40	Supply,installation, testing & Commissioning of electrically operated Hot Water Generator of 80 KW actual capacity made of 8mm M.S. sheet and dish end made of 10mm M.S. having 16 gauge stainless steel lining with heaters arranged in banks and Controller and Thermostat so that suitable GPM hot water is generated at 50°C with nominal variation, including 75mm thick resin bonded fibre glass insulation of 24 Kg / CUM density finished with 1.25mm thick aluminium sheet cladding including necessary Electrical panel with BMS compatible having suitable Incoming and outgoing Switchgears for Boiler, automatic Controls including inlet and outlet connections for water complete with pressure release valve, low level cut-out, Autovent sight-glass as per specification complete as required. (Degree of protection IP52 with IS 2147)
41	The price includes loading/unloading and shipment till site Including Insurance Charges ,Unloading at site,RCC Foundation, placement of HWG on the foundation, co-ordination during execution, rendering necessary guidance for execution, supervision, testing, commissioning and startup of above mentioned HWG.
42	Heating Capacity 100KW (With Multiple Bank)
43	(Make: As per approved make list attached)
44	PUMP SETS
45	PRIMARY VARIABLE SPEED PUMPING SYSTEM
46	Supply, installation, testing and commissioning of PN16 rated Vertical Inline Split Coupled single stage centrifugal pump each capable of delivering the specified flow rate comprising the following and complete as per specifications. Casing (Volute) - Ductile Iron.Impeller - 316 SS - Statically and Dynamically BalancedCasing Gasket - Confined Non Asbestos FiberPump Shaft - 316 SS .Flush Line - Braided Stainless SteelMechanical Seal - Outside Balanced (the pump design shall meet the requirement of servicing / changing the mechanical seal without disturbing the pump shaft alignment) with external flushline. Motor Type - TEFC Squirrel Cage, Efficiency Class - I FIVE, Insulation - Class F, 415V ± 10% , 50Hz ± 5%, 3Ø AC Power Supply, RPM as per OEM standard.
47	VFD - Integrated motor mounted over Pump with IP- 55 protection. pump should operate through sensorless control or wireless DPT control.Pump Efficiency should be more than 75% Integrated fliter to meet EN61800-3 for RFI Control, Integrated DC link Reactor equivalent in performance to a 5% AC line reactor.All the VFD should display the dynamic head & flow rate of the pump using inputs from ultrasonic flow meter and digital pressure gauge or using sensorless alogorithms,( Per pump,1 flow meter and 2 pressure gauges to be supplied and integrated with motor mounted VFD driven pump for the display of flow and head on VFD). Pump manufacturer to supply Ultrasonic flow meter and digital pressure gauges along with the pumps supplied or can display individual flow and head per pump on respective VFD using sensorless alogorithms
48	The Price includes all clearance charges, unloading and shipment till site Including Insurance Charges ,Unloading at site,RCC Foundation, placement of PUMPs on the foundation, co-ordination during execution, rendering necessary guidance for execution, supervision, testing, commissioning and startup of above mentioned pumps.
49	The system shall be complete in all respects and suitable for following ratings and duty.
50	528 USGPM * 40 M Head or as per actual at site with Min Efficiency. 75% for Chilled water circuit (2Working + 1Standby)
51	(Make: As per approved make list attached)
52	Microprocessor Based Pump Logic Controller for Primary variable pump
53	SITC Separate (Not as apart of VFD) Microprocessor based Primary variable pump logic controller in IP 54 protection, to control following nos. Pumps. Suitable to operate on Sensorless/ wireless mode ( 3 wireless DP sensor to be consider for each zone) & Should be Modbus RTU/ BACnet enabled for communicating with BMS & RS-485 serial communication with Pump VFD. The staging of pumps should be based on efficiency (not on capacity) to ensure minimum operating cost. End of curve protection should be sensorless control based Power Rating: 230 V/ 1 ph/ 50 Hz Display: Minimum 4.3\\" backlit LCD Hand-Off-Automatic (H-O-A) control Secure front cabinet door with lock and key UL Listed and CSA Approved Remote or local start/stop mode of operation. 2-level (field and factory) password security Remote zone signals, zone faults, zone setpoint and active control zone Note : All above should be sourced from OEM as a single unit
54	For Chilled water pumpset (2W + 1S)
55	(Make: As per approved make list attached)
56	CONDENSOR WATER PUMPS (FIXED SPEED)
57	Supply, installation, testing and commissioning of PN16 rated Vertical Inline Split Coupled ( Long coupled Type ) single stage centrifugal pump each capable of delivering the specified flow rate comprising the following and complete as per specifications. Casing (Volute) - Cast Iron.Impeller - Gunmetal Bronze - Statically and Dynamically BalancedCasing Gasket - Confined Non Asbestos FiberPump Shaft - SS 316/416.Flush Line - Braided Stainless SteelMechanical Seal - Outside Balanced (the pump design shall meet the requirement of servicing / changing the mechanical seal without disturbing the pump shaft alignment) Motor Type - TEFC Squirrel Cage, Efficiency Class - IE3, Insulation - Class F, 415V ± 10% , 50Hz ± 5%, 3Ø AC Power Supply
58	The price includes loading/ unloading and shipment till site Including Insurance Charges ,Unloading at site,RCC Foundation, placement of PUMPs on the foundation, co-ordination during execution, rendering necessary guidance for execution, supervision, testing, commissioning and startup of above mentioned pumps.
59	880 USGPM * 30 M Head or as per actual at site with Min Efficiency. 75% (2Working + 1Standby)
60	(Make: As per approved make list attached)
61	Hot Water Pump (Monsoon Reheating)
62	Supply,erection, testing and commissioning of monoblock Hot water centrifugal pump for hot water recirculation, pump set capable of delivering Min.130 GPM of water against 24 mtr head each comprising of the following and complete as required
63	1 No. - monoblock type pump with bronze impellar and mechanical seal.
64	Duly insulated with 80 kg/cum density resin bonded fiber glass cladded with aluminium sheets of 0.5mm thickness and properly clamped to pump in two semicircular sections as per specifications.
65	1 No. Suitable HP, TEFC squirrel cage induction motor(Eff-3) with class ' B' insulation, 3000 RPM (±10%) synchronous speed, operating on 415 Volts + 10 % , 3 phase , 50 Hz A.C. supply.
66	The price includes loading/ unloading and shipment till site Including Insurance Charges ,Unloading at site,RCC Foundation, placement of PUMPs on the foundation, co-ordination during execution, rendering necessary guidance for execution, supervision, testing, commissioning and startup of above mentioned Pumps.
67	Pump as above (1 working + 1stand by)
68	(Make: As per approved make list attached)
69	Cooling Tower (CTI Certified)
70	Supply, installation, testing and commissioning of CTI Approved standard Rectangular type FRP Induced Draught Counter flow cooling tower with Multi Cell. Motors shall be suitable for VFD's , IP65 and Premium efficiency of IE3 with neccessory accessories, FRP water basin, PVC fillings with integral louvers and drift eliminators, hot water distribution by gravity complete with statically and dynamically balanced axial flow Fans, Direct driven fans with TEFC induction motor and temperature sensor suitable for operation on 415 + 10% volts, 50 Hz. AC supply, suction screen, make up with float valve and quick fill arrangement, overflow and drain connections, suitable inspection ladder, access arrangement for cooling tower interior, MS supporting structure, anti-vibration mountings ,cement concrete foundation, steel/ mesonary supporting structure complete as per specifications as required. Design shall be as below ,IP 55 rated Locable Isolator Switch with cooling tower along with all Isolators for CT Complete in all respect.
71	WBT : at 85º F
72	WB Approach : 2.77º C Maximum
73	Hot water IN : 97.5 ºF
74	Hot water OUT : 90ºF
75	Water Flow Rate : 880 USGPM
76	The price includes loading/unloading and shipment till site Including Insurance Charges ,Unloading at site,RCC Foundation, placement of Cooling Tower on the foundation, co-ordination during execution, rendering necessary guidance for execution, supervision, testing, commissioning and startup of above mentioned Cooling Tower.
77	Heat Rejection Capacity : 3,432,000 BTU/hr (2W + 1S)
78	(Make: As per approved make list attached)
79	AIR HANDLING UNITS
80	Supply, installation testing and commissioning of Double skin air handlers, complete with thermal break profile ,the various sections, chilled water coils,centrifugal Forward/backward (Airofoil) curved blade fan and in Ceiling Mounted forward/Backward curved blade fan , direct driven/drive sets, squirel cage induction motor with minimum IE 3 efficiency, and vibration isolators and with Thermal Break profile as described in the specifications & AHU schedule.
81	Supply, installation testing and commissioning of AHUs as per the mentioned in AHU schedule.
82	AHU FOR OT's AND ICU ((All AHU Motors /controls Should be VFD and BMS Compitable )
83	Supplying, installing, testing and commissioning of factory built weather Proof Floor Mounted /Ceiling suspended double skin type air handling units with thermal break profile made of 48+-2 mm thick panels consisting of pre plasticized G.I casing made of thickness 0.8 mm outside layer and Aluminium sheet of thickness 0.8mm inside layer with polyurethene foam (PUF) CFC Free insulation of density 40+-2 kg/m3 factory injected between them by injection moulding machine, complete with blower section with blower DIDW backward/Forward curved centrifugal fan of below mentioned static pressures for FM/CS AHU's, 6 row deep cooling & Heating coil,2 row deep Monsoon reheating coil, section with hydrophillic aluminium finned copper tubes (tube thickness not less than 0.5mm), Filter section with 50 mm thick flange type pre filter & MERV-13 fine filter on discharge or as per site requirement. , belt drive package with TEFC drive motor suitable for 415 ± 10% volts, 50 Hz, 3 phase, A.C supply,Mixing box with Aluminium Anodised Extruded dampers at fresh and return air cutouts, drain connections with drain valve, stainless steel drain pan, thermometers and pressure gauge at the inlet and outlet of cooling coil, necessary vibration isolation arrangement ,Light,etc,Whole unit should by AHRI Certified complete as per specifications of following capacity:
84	Including Hardware for hanging of AHU with GI thread rods, check nuts/washers
85	PAN type Humidifier: Thyrister Based Pan Type Humidifier for Humidification of dry ambient along with its all connecting wires for all FM type AHUs
86	Variable Frequency drive for for all AHU motors and all dampers must have BMS compatibale
87	CFM TYPE SP CC /TR
88	1200 CS 100 (6+2) RD /3.0 along with HEPA Recovery Room + Change Rooms + Corridoor at 4th floor (a part of septic OT Area)
89	2000 CS 100 (6+2) RD /5.5 along with HEPA filter for HDU at 2nd Floor
90	2200 CS 110 (6+2) RD /6.0 along with HEPA filter for ICUs
91	2700 CS 110 (6+2) RD /7.0 along with HEPA filter for ICUs
92	3500 CS 110 (6+2) RD /10.0 along with HEPA filter for Minor OT at 2nd Floor
93	4000 CS 110 (6+2) RD /10.0 along with HEPA filter for ICU & Isolation Room at 4th Floor
94	3000 CS 110 (6+2) RD /8.0 Septic OT at First Floor (Hepa filters to be provided in OT Plenum)
95	3000 CS 110 (6+2) RD /8.0 Septic Labour Ward at 2nd Floor along with Hepa Filters
96	3100 CS 110 (6+2) RD /10.0 Delivery Room with HEPA filters for Epidural Room at Gr Floor
97	4000 FM 125 (6+2) RD /10.0 for OT1 & OT2 at FF (Hepa filters to be provided in OT Plenum)
98	(Make: As per approved make list attached)
99	Floor Mounted AHU's (5.2)
100	Supplying, installing, testing and commissioning of factory built weather Proof Floor mounted double skin type air handling units with thermal break profile made of Min 32+-2 mm thick panels consisting of pre plasticized G.I casing made of thickness 0.8 mm outside layer and sheet of thickness 0.8mm inside layer with polyurethene foam (PUF) CFC Free insulation of density 40+-2 kg/m3 factory injected between them by injection moulding machine, extra 25mm acoustic insulation of opencell nitrile rubber with 0.8mm AL perforated sheet, complete with blower section with blower DIDW backward curved centrifugal fan for FM AHU's, 6 row deep cooling coil, section with aluminium finned copper tubes (tube thickness not less than 0.5mm), Filter section with 50 mm thick box type pre filter & microvee filter on common frame. , belt drive package with TEFC drive motor(IE-3) suitable for 415 ± 10% volts, 50 Hz, 3 phase and VFD Compatible, A.C supply,Mixing box with Aluminium Anodised Extruded dampers at fresh and return air cutouts.,drain connections with drain valve, stainless steel drain pan, thermometers and pressure gauge at the inlet and outlet of cooling coil, necessary vibration isolation arrangement etc, Whole unit should by AHRI Certified complete as per specifications of following capacity.
101	CFM TYPE SP CC /TR
102	7000 FM 80 6.0 RD 17
103	9000 FM 80 6.0 RD /25
104	10500 FM 80 6.0 RD /25
105	(Make: As per approved make list attached)
106	Ceiling Suspended AHU
107	Supplying, installing, testing and commissioning of factory built weather Proof Ceiling Suspended double skin type air handling units with thermal break profile made of Min 32 +-2 mm thick panels consisting of pre plasticized G.I casing made of thickness 0.6 mm outside layer and sheet of thickness 0.6mm inside layer with polyurethene foam (PUF) CFC Free insulation of density 40+-2 kg/m3 factory injected between them by injection moulding machine, complete with blower section with blower DIDW backward/Forward curved centrifugal fan for CS AHU's, 6 row deep cooling coil, section with aluminium finned copper tubes (tube thickness not less than 0.5mm), Filter section with 50 mm thick box type pre filter & microvee filter on common frame. , belt/Direct drive package with TEFC drive motor(IE-3) suitable for 415 ± 10% volts, 50 Hz, 3 phase and VFD Compatible, A.C supply,Mixing box with Aluminium Anodised Extruded dampers at fresh and return air cutouts.,drain connections with drain valve, stainless steel drain pan, thermometers and pressure gauge at the inlet and outlet of cooling coil, necessary vibration isolation arrangement,Light, etc, Whole unit should by AHRI Certified complete as per specifications of following capacity:
108	CFM TYPE SP CC /TR
109	1500 CS 55 6.0 RD /4.0
110	2000 CS 55 6.0 RD /5.0
111	2200 CS 55 6.0 RD /5.5
112	2800 CS 55 6.0 RD /7.0
113	3000 CS 55 6.0 RD /8.0
114	3500 CS 55 6.0 RD /8.0
115	3500 CS 55 6.0 RD /11.0
116	4000 CS 65 6.0 RD /10.0
117	4400 CS 65 6.0 RD /11.0
118	(Make: As per approved make list attached)
119	Treated Fresh Air Units
120	Supplying, installing, testing and commissioning of factory built Ceiling Suspended/Floor Mounted double skin type air handling units with thermal breakprofile for design of 100% fresh air made of min 25 mm thick panels consisting of pre plasticized G.I. casing of thickness 0.8 mm outside layer and plane GI of 0.8mm inside layer with polyurethene foam (PUF) insulation of density 32 kg/m3 factory injected between them by injection moulding machine, complete with blower section with blower DIDW backward curved centrifugal fan, 8 row deep cooling with aluminium finned copper tubes (tube thickness not less than 0.5mm), Min MERV 7/10 Pre filter sections or as per norms , belt drive package with TEFC drive motor suitable for VFD & 415 ± 10% volts, 50 Hz, 3 phase, A.C supply, complete, drain connections with drain valve, light,stainless steel drain pan ,necessary vibration isolation arrangement etc, Whole unit shall be ahri certified ,complete as per specifications of following capacities :
121	CFM TYPE SP CC /TR
122	2000 CS 70 8 RD /20
123	AHU For Exhaust
124	Supplying, installing, testing and commissioning of factory built Floor Mounted/Ceiling suspended double skin weather Proof type air handling units made of 25 mm thick panels consisting of pre plasticized G.I. casing of thickness 0.6 mm outside layer and plane GI of 0.6mm inside layer with polyurethene foam (PUF) insulation of density 32 kg/m3 factory injected between them by injection moulding machine, complete with blower section with blower DIDW backward/Forward curved centrifugal fan, belt drive package with TEFC drive motor suitable for VFD & 415 ± 10% volts, 50 Hz, 3 phase, A.C supply, complete with canvass connections ,necessary vibration isolation arrangement etc, complete as per specifications of following capacity
125	800 CFM 75 mm Static with Hepa Filter(H-13) of 99.77% to 3 Micron & Micro Vee Filters at discharge and Pre Filters with MERV 8
126	700 CFM 75 mm Static with Hepa Filter(H-13) of 99.77% to 3 Micron & Micro Vee Filters at discharge and Pre Filters with MERV 8
127	660 CFM 45 mm Static with Min MERV 7 Pre filter sections and MERV 14 Fine filters at discharge )
128	800 CFM 45 mm Static with Min MERV 7 Pre filter sections and MERV 14 Fine filters at discharge)
129	(Make: As per approved make list attached)
130	FAN COIL UNITS (Standard)
131	Supply,Installation , testing and commissioning of fan coil units of specified capacities and air flow as per the specifications, complete with auxillary drain pan
132	Fan coil unit shall be supplied with approved make of factory fitted adequately sized insulated (with nitrile foam) two way motorized valves , insulated brass ball valves-one with Y strainer, and the other without Y strainer complete with room thermostat for fan speed control , associated conduiting and wiring between the thermostat , 2 - way valve .etc.
133	Cost of fan coil unit shall be inclusive of approved make room thermostat (heating and cooling, with fan speed control), and associated MS conduiting and wiring etc.between the thermostat and two way valve, for a standard length of approximately 5-7 M per fan coil unit.
134	Providing and fixing in position the following Fan Coil units complete with all valves and accessories as described above.
135	1.5 TR nominal capacity ( 600 CFM)
136	2.5 TR nominal capacity ( 1000 CFM)
137	(Make: As per approved make list attached)
138	WATER COOLED CASSETTE ACS
139	Supply, installation, testing & commissioning of Water cooled Cassette Unit suitable for both heating/cooling with copper tube and aluminium finned cooling coil, low noise fan and motor with ON/OFF and 3 speed control and suitable for 1 phase, 230 + 6%V, 50 Hz electric supply, with cordless remote/corded control, fabric filter, drain pump, and decorative front grille. The Unit shall be complete with stainless steel duly insulated main and auxiliary drain pan. The unit shall be complete with electrical terminal strip, wiring in conduit upto thermostat box or any other advance technology. Unit shall have copper pipes for coil connection complete . The unit shall also have fresh air pocket provision. The front grill shall be 4 way type. The noise level at low speed shall be in the range of 38 to 42db & at high speed upto 45db. Noise levels are at a distance of 2M from the unit. (Note :Tonnage Variation allowed upto ±5%) : Note: Vendor should include the cost of of copper pipe connection upto 1m along with all accessories complete in all respect
140	3.5-4.0 Tr Four way
141	AOP cell with NANOX & PLASMAOX technology & Bi Polar Ionizer.
142	SITC of Advanced Oxidation Pentplasma (AOP) cells comprising of UVC lamp 254 NM on NANO metallic compound target Alumninum matrix cell duly enclosed by a poly casing tube, with the capability to produce plasma Hydroxyl oxidizers along with anti microbial coating (EPA Approved). The unit shall have inbuilt multipin ion generator (+-10^6) pins along with ultrasonic radio frequency waves for pest repellancy. The UV-C lamp will be a low-pressure mercury type and of such intensity as to provide minimum performance as listed below. The UV-C lamp will produce only Germicidal UV (by definition this means 99.99% UV-C energy).The cell will have built in LED indication system stating the operation of the 3 technologies the UV lamp, ionizer and pest repellant. The power / control cabling between the Pentagon units and the power source / controls shall be included in the cost .The system shall be capable of reducing microbial bacteria, Covid 19 virus,virus and spores , VoC’, odors and particulates matter. The equipment shall conform to CE and ROHS. Standards certifications shall be submitted along with the technical submital. The Pentagon cells should be selected by considering a load factor calculation for each specific area where the equipment is to be installed. The wattage shall not be less than mentioned. The AOP/ Pentagon Cells Should be complete with Transformers, control cabling and Plug Top & necessary power cable.
143	Duct Mounted AOP with UVC Lamp System for following Air Flow's
144	Upto 1500 CFM
145	1501 CFM to 6500 CFM
146	6501 CFM to 15000 CFM
147	(Make: Ultrafresh, VS Eviropure, Ultrapure)
148	Temperature and RH sensor and adjuster package.
149	Supply,install-(grout),test and commission micro-processor based Room temperature, humidity sensor and remote adjuster package within a MS housing -wall ,suitable for mounting, and having a stainless steel cover plate.This package shall have a temperature and humidity display - red 2\\" high LED character for operation rooms, and other critical areas.
150	Sensor, adjuster (Snap acting humidistat/Proportional thermostat- Microprocessor based) and displayer package, as described above.
151	(Make: As per approved make list attached)
152	Pan Type humidifier and humidistat
153	Supply, install, test and commission snap acting humidistat .
154	Supply, install, test and commission wall / floor mounted Pan Type Humidifier package of following capacities.
155	3.0 KW
156	(Make: As per approved make list attached)
157	EXPANSION TANK
158	Supply, Installation ,Testing and commissioning of MS.Open expansion tank with minimum thicknessof 3.0mm as per the specifications.The Open vessel expansion tank shall be complete with all accessories so as to make it ready for installation and commissioning on site.The tank shall be insulated with the approved method of insulation, and shall be complete with water make-up connection and system .The expansion tank will be supplied,Non return Valve ,Float valve,Ball Valves and interconnecting piping etc.
159	2000 Ltr . Open Expansion Tank duly insulated and with all accessories.
160	AIR SEPARATOR
161	Supply,installation,testing and commissioning of Microbubble Air & Dirt Separator,with matching flanges, bolts, nuts & gasket, PN16 complete with flanged connection and as per the specifications as detailed earlier in the relevant section of specifications , and duly insulated with 50 mm thick TFF expanded polysterene and cladded with 26G aluminum sheet.
162	200 mm Dia Air Separator, duly insulated.
163	(Make: As per approved make list attached)
164	Supplying, fixing, testing and commissioning of following valves, strainers, gauges in the chilled water plumbing duly insulated to the same specifications as the connected piping and adequately supported as per specifications. (Make: As per approved make list attached)
165	SITC Water Flow Switches (Brass body) .
166	SITC Auto Air Vent Valve 1/2\\".
167	PICV Valves
168	Supply, Installation, Testing & Commissioning of Insulated Two- way ball type pressure independent control valve with flanged end ISO7005-2, flow capacity as desired, Min.PN16, equal percentage flow characteristic, body GGG50 ductile iron with stainless steel ball. Non spring return rotary type modulating actuator, torque as required, close-off min pressure 700 kPa, power supply 24 V AC/DC, control signal 2-10 V DC, feedback signal 2-10 V DC, IP54.
169	65 mm dia
170	50 mm dia
171	40 mm dia
172	32 mm dia
173	25 mm dia
174	20 mm dia
175	15mm dia
176	(Make: As per approved make list attached)
177	Brass Ball Valves
178	SITC of Brass Ball Valves of dia 40mm with Strainer
179	SITC of Brass Ball Valves of dia 40mm without Strainer
180	SITC of Brass Ball Valves of dia 32mm with Strainer
181	SITC of Brass Ball Valves of dia 32mm without Strainer
182	SITC of Brass Ball Valves of dia 25mm with Strainer
183	SITC of Brass Ball Valves of dia 25mm without Strainer
184	(Make: As per approved make list attached)
185	VALVES/CONTROLS - PN-16 without Insulation (Make :as per approved make list attached).
186	Supplying, fixing, testing and commissioning of following valves, gauges and strainers for condenser water circulation as per specifications.
187	BUTTERFLY VALVE (MANUAL) with C I body SS disc nitrile sheet O - ring & PN 16 pressure rating as specified.
188	250 MM DIA (Gear Box type)
189	BALANCING VALVE WITH BUILT IN MEASURING FACILITY with C I body flanged construction with EPDM coated disc with long pitch with protected out pipe insulation & PN 16 pressure rating for chilled / hot water circulation as specified.
190	200 MM DIA
191	150 MM DIA
192	Y- STRAINERS (PN-16)
193	Providing and fixing in position the following Insulated Y-Strainers
194	200 mm dia
195	POT- STRAINER(PN-16)
196	Proiding and Fixing of Pot strainer with drain valve complete in all respect of following dia
197	250 mm
198	NON - RETURN VALVE with duel plate of C I body SS plates vulcanized NBR seal flanged end & PN 16 pressure rating for chilled / hot water circulation as specified.
199	200 MM DIA
200	SITC Water Flow Switches (Brass body) complete with copper control wiring at chiller outlet of each machine
201	AUTO AIR VENT
202	Supply, installation ,testing and commissioning of Auto Air vents,at the specified locations in the chilled water piping , alongwith isolation ball valves, as per approved makes
203	Auto air vent with isolating ball valves (15 mm dia)
204	CONDENSATE DRAIN PIPE
205	Providing and fixing and in position the following PVC pipes (Min. Thickness 3.0mm) for condensate drain duly insulated with minimum 6.0 mm 'O' Class Nirile rubber & duly secured with adhesive tape as per specification ,cut to required length and installed with all joints , including the necessary fittings. (For all the AHU/FCU units upto the main header in the shaft dor vertical risers
206	65 mm dia
207	50 mm dia
208	40 mm dia
209	32 mm dia
210	25 mm dia
211	(Make: As per approved make list attached)
212	Factory Fabricated Duct - AL duct
213	Supply,Fabrication , Installation and testing of Aluminium sheet metal ducts in accordance with the approved shop floor drawings and specifications , and shall also confirm to the BIS specifications. The hardware shall be chrome plated or of stainless steel.All lateral and transverse joints shall be sealed with silicon based mastic sealant.
214	Aluminum Sheet thickness - 22 Gauge
215	Aluminum Sheet thickness - 20 Gauge
216	(Make: As per approved make list attached)
217	Fresh Air/Exhaust Air Louvers
218	Supply, Installation, Testing and Commissioning of extruded aluminium louvres with frame bird screeen 50 mm pre-filter with frame, mounting arrangement etc. as per specifications and drawings.
219	Fresh Air/Exhaust Louvers
220	(Make: As per approved make list attached)
221	HEPA Filters & OT Plenum for Laminar Flow
222	SITC of Aluminium white epoxy powder coated Factory Fabricated O.T. PLENUM (Aprox.size 6'x6') & HEPA Filters Having efficiency 99.97%down to 3 Micron ,I.P.D < 15 mm HG & F.P.D. = 50 mm HG, The Hight of OT Plenum should not be more than 290 mm
223	SITC of Aluminium white epoxy powder coated Factory Fabricated O.T. PLENUM (Aprox.size 8'x6') & HEPA Filters Having efficiency 99.97%down to 3 Micron ,I.P.D < 15 mm HG & F.P.D. = 50 mm HG, The Hight of OT Plenum should not be more than 290 mm
224	(Make: As per approved make list attached)
225	MECHANICAL INSULATION
226	DUCT LINE ACOUSTIC TREATMENT
227	Supply, Installation, Testing and Commissioning of Acoustic lining inside ducts/plenum using open cell nitrile rubber foam having microban anti-microbial/ anti fungal product protection and of 160-180 kg / m³ density as per ASTM D3575, class 1 ratingn As per BS476,PART-7, cut to required sizes and to be stuck to the inside of duct surfaces with adhesive as approved by the manufacturer. (Rubber based solvent). as per specifications
228	15mm thick sound board for Floor Mounted AHU's
229	10mm thick sound board for CS AHU's
230	(Make: As per approved make list attached)
231	DUCT LINE THERMAL INSULATION(Inside Conditions)
232	SITC of Physically / Chemically crosslinked polyethylene foam, with factory reinforced alupet foil facing, ANTI MICROBIAL/ANTI FUNGAL,HFC & CFC free , Negligible VOC level with Class O fire properties,with very low fire propagation of < 5.5 and passing E-84 at < 25/50, as per technical specification, the density of the foam should be not less than 25-30kg/m3 and the maximum thermal conductivity K should be 0.032W/mK@ 23 Deg C , the permeability resistance factor u shouldn't be less than 14000. The product shall have temperature range of –20oC to 115oC
233	13 mm thick
234	(Make: As per approved make list attached)
235	DUCT LINE THERMAL INSULATION (Outside Conditions exposed to sun)
236	Physically / Chemically crosslinked polyethylene foam, with factory laminated heavy duty and ultra tough multi-layered composite aluminium foil facing, with puncture resistance of >400N and Class O fire properties as per BS 476 Part BS 476 Part 6 & 7 and as per the tender technical specification and density of the foam should be not less than 25 - 30 kg/m3 and maximum thermal thermal conductivity K should be 0.032W/mK@ 23 Deg C & the permeability resistance factor u shouldn't be less than 97000.
237	25mm thick
238	ASSOCIATED ELECTRICAL WORKS
239	The rates for the distribution boards from the Breakers and instruments shall also include the following :
240	A ,Wiring for light / Fan points with 1.5 sq. mm PVC insulated copper conductor 1100 Volt grade stranded flexible FRLS wires of approved make in 1.6 mm thick 25 mm dia MS conduit including cost of providing & fixing saddles, hangers, supports,cutting chases and filling chases for recessed conduiting, and including the cost of providing and fixing a 6 amp 240 Volt Modular Plate type switches of approved quality, colour, make and design with moulded cover plate in zinc chromate passivated MS box and including the cost of running 1.5 sq. mm PVC insulated copper earth wire for loop earthing etc. complete
241	B TPN ACB’s / MCCB’s shall mean 3 pole ACB’s / MCCB’s with adequate size of neutral link
242	C All MCB’s shall be of minimum 10 KA breaking capacity or as metioned in BOQ.
243	D The breaking capacity of MCCB’s are mentioned panel wise. All MCCB’s shall be with thermal magnetic microprocessor releases as per BOQ and following
244	i. MCCB rating upto 250 Amps with thermal magnetic releases
245	ii. MCCB above 250 Amps with microprocessor releases.
246	All MCB’s used for protection of resistive and lightly inductive load shall be type “B” characteristic and inductive (motor) load shall be of type “C” characteristic.
247	F Degree of protection for following type of distribution panel enclosure shall be as per IS:13947-1993
248	IP 42 for indoor panels.
249	ii. IP 55 for ODU panel.
250	G All MCCB’s shall be provided with operating mechanism for door interlock
251	H All hinged door shall be earthed through 2.5 sq mm tinned braided copper wire.
252	I Providing cable clamps / supports within distribution boards cable alley.
253	J Current density of aluminium shall be 1sq mm for 1.0 Amps for rated current of bus bars.
254	K Model, current capacity location and frame size of switchgear shall be written inside of the panel doors with paint / permanent marker as approved shop drawings / site requirment
255	L All meter shall be digital type.
256	M Current Transfomer shall be resin cast.
257	N All Panels Must be BMS Compatible
258	Main Electrical Panel
259	Design, fabrication, assembling, wiring, supply, installation, testing and commissioning of following LT panels fabricated out of 14 guage for load bearing and 16 gauge for non load bearing CRCA sheet steel in cubical formationwith reinforecment of suitable size angle iron and channel T iron flats. All steel material used in the construction of panels shall be powder coated. A solid busbar shall be provided at the bottom of the panel with two connecting eyes for termination. The boards shall be suitable for 415 volts, 50 Hz, 3 phase , 4 wire supply system. All the hardware used in the fabrication of the panel shall be galvanized with zinc passivation. The panel shall be compartmentalized to accommodate one feeder in each compartment. A vertcal cable alley of suitable width shall be provided to serve on or two vertical feeder sections. Also the opening between the busbar chamber and the feeder section shall be shrouded with bakelite / hylam sheet with min.3 mm thickness.
260	The panel drawing shall be approved before taking up the fabrication and Sall have compatible BMS for future requirment.
261	In All panels Each starter should have remote control compatibilty and interlocking facilities including auto manual switch, NO/NC contacts for control and must have auto manual operation suitable to take signal from fire alarm panel for automatic operation of fan in case of fire. All smoke /vent. fan panel the starters shall have suitable facility to operate with fire sensing control modules.
262	Plant Room Panel
263	1 No.1600 amp EDO ACB 65 KA with Microprocessor release alonwith protection of S/c, E/F, etc
264	Multi Function Digital Meter class 1.0 Accuracy Schnieder series 64XX or equivalent of the same model in Elmeasure/ HPL/Reputed with CTs of the desired rating as per the load
265	Phase indicating lights RYB with control fuses.
266	Breaker ON/OFF/TRIP indicating
267	lights. Bus Bars
268	2000 amp TPN Aluminum Bus Bar with heat shrinkable insulation colored sleeves.
269	Outgoings
270	3 Nos. 400 amp, MCCB with an adjustable release, 50 KA with Rotary operating handles for Chiller
271	3 Nos. MCCB for 25 KW or as per the rating of the Chilled water pumps by the Chiller Manufacturer (2Working + 1Standby) for primary Chilled water Pumps without starter as VFD to be available on Chilled water pump side with Digital Ampere Meter Class 1.0 with CT of suitable rating
272	3 Nos MPCB for 27 KW or as per rating of the Condenser water pump and the Star Delta starter with Contactors as per the Cordination chart with O/L Relay, S/D Timer and SPP (2 working + 1 Standby)with Digital Ampere Meter Class 1.0 with CT of suitable rating
273	3 Nos MPCB for 7.5 KW x 2nos or as per the manufactrer specifications for the cooling towers with the DOL starter with Contactor as per the Cordination chart with O/L Relay and SPP (2 working + 1 Standby) with Digital Ampere Meter Class 1.0 with CT of suitable rating
274	2 Nos MPCB for 10KW or as per rating of the Monsoon Re-heating pump and the Star Delta starter with Contactors as per the Cordination chart with O/L Relay, S/D Timer and SPP (1 working + 1 Standby) with Digital Ampere Meter Class 1.0 with CT of suitable rating
275	2 Nos. 450-600 amp, MCCB with an adjustable release, 36 KA with Rotary operating handles for HWG (1W plus 1Standby) with Digital Ampere Meter Class 1.0 with CT of suitable rating
276	2 Nos. 200 amp, MCCB with an adjustable release, 36 KA with Rotary operating handles for HWG (1W plus 1Standby) with Digital Ampere Meter Class 1.0 with CT of suitable rating
277	3 Nos DP MCB 6Amps 10 KA for supplying to various control equipment
278	1 Nos MCCB upto 300 Amps for AHU distribution panel
279	1 Nos, spare space MCCB upto 100 Amps
280	Unloading at site, placement of Panel on the foundation,Making foundation, co-ordination during execution, rendering necessary guidance for execution, supervision, testing, commissioning and startup of above mentioned Panel along with all accessories.The panel drawing shall be approved before taking up the fabrication from EIC
281	(Make: As per approved make list attached)
282	HVAC AHU Panel with Exhaust AHU along with VFD
283	Incoming
284	1 No. 63 amp MCCB TP 25 KA with Rotary Mechanism and spreader links
285	Phase indicating lights with control
286	fuses. Breaker ON/OFF/TRIP indicating
287	lights. Bus Bars
288	100 amp TPN Aluminum Bus Bar with heat shrinkable insulation colored sleeves
289	Multi function meter Digital with suitable CT type class 1.0
290	Outgoings
291	2 Nos. MCB TPN 6-32 Amps to supply to VFDs (AHU & Exhaust VFD) Rating of the TPN as per the VFD maximum load with Digital Ampere Meter Class 1.0 with CT of suitable rating
292	2 Nos VFD of HP rating as per the AHU and Exhaust AHU with console or related interface to be working with the controller provided by the AC company, herein referred to as the DTS/DDC Controller with Digital Ampere Meter Class 1.0 with CT of suitable rating
293	1 Nos DP MCB 16 Amps
294	2 Nos. 6 A, MCB for UVC Lamp (if required)
295	Transformer or powersupply with MCB DP 6 Amps
296	(Make: As per approved make list attached)
297	Sub Panel for AHU Motors up to 5.5 KW
298	SITC of Wall mounted sub panel boards for AHUs, Blower with switch, starters, lamps inter connections, current operated single phase preventer, A/M switch etc. as per specifications and drawings and as required.
299	1 No. incoming upto 32Amps 4 pole TP+NL MCB with Digital Mutli function Meter Class 1.0 with CT of suitable rating
300	RYB Indicators
301	2 Nos. Push Buttons On/Off
302	1 No. single phase preventor
303	1 Nos. DOL starter with Power contactor and MPCB as incomer of the starter with SPP with Digital Ampere Meter Class 1.0 with CT of suitable rating
304	1 No MCB DP
305	2 Nos. 6 A or suitable, MCB for UVC (if required)
306	(Make: As per approved make list attached)
307	Sub Panel for AHU above 5.5 KW
308	SITC of Wall mounted sub panel boards for AHUs, Blower with switch, starters, lamps inter connections, current operated single phase preventer, A/M switch etc. as per specifications and drawings and as required.
309	1 Nos. 63-100 Amps TP+NL MCCB 25 KA ICU=ICS=100% with Terminals, ROM and necessary accessories with Mutlifunction Meter Class 1.0 with CT of suitable rating
310	RYB Indicators
311	2 Nos. Push Buttons On/Off
312	1 No. single phase preventor
313	1 Nos. Star Delta starter with Power contactor and MPCB as incomer of the starterwith SPP with Digital Ampere Meter Class 1.0 with CT of suitable rating
314	1 No MCB DP
315	2 Nos. 6 A or suitable, MCB for UVC lamp (if required)
316	(Make: As per approved make list attached)
317	Distribution Panel for Ventilation Axial Fans (Separate Supply or independent supply required from generator )
318	Design, fabrication, assembling, wiring, supply, installation, testing and commissioning of Wall/Floor mounted sub ditribution panel board for Ventilation Axial Fans Powder Coated Enclosure made out of TATA make CRCA sheet having 2 mm for load bearing surfaces & 1.6 mm for non load bearing surfaces ,duly powder coated having Siemens grey colour.as per specifications and drawings and as required.OEM/Panel Builder should CPRI approved at least 70K
319	Incoming TPN MCCB FEEDER
320	1 No 160-200A, TPN 50KA MCCB with TMD Release having O/L,S/C, protections (ICU=ICS=100%)
321	1 No.Rotary Handle for 200A MCCB
322	1 No.Spreader Links for 200A TP
323	1 No.Aux. Contact Block
324	1 No.Multifunction Meter with builtin Selector switch
325	3 Nos.CT's 200/5A For Metering
326	3 Nos Indication Lamp R-Y-B
327	4 nos Control MCB 6A SP.10KA Type C
328	3 nos CT Shorting Link
329	4 nos Control Terminals
330	Out Going 16-63A TPN MCCB FEEDER
331	25 Nos MCB TPN 16-40 amps
332	25 Nos Indication Lamp ON
333	Panel
334	400A rating TPN Aluminium Bus Bar of Electrolytic Grade E-91E Bus Bar Supports, Colour Coded PVC Heat Shrinkable Sleeves
335	Hardware (PVC Cahnnels/MCB Channels/Fibre- Glass Gaskets/ Sleevs/ nuts/ bolt/ washers/ cooling fans etc Including complete wiring,thimbles etc.
336	Unloading at site, placement of Panel on the foundation, co-ordination during execution, rendering necessary guidance for execution, supervision, testing, commissioning and startup of above mentioned Panel.The panel drawing shall be approved before taking up the fabrication from EIC
337	(Make: As per approved make list attached)
338	Sub Distribution Panels for AHU's
339	SITC of panel board made of 1.6mm for non load bearing /2.0 mm thick steel sheet for non load bearing sections duly powder coated complete with Metering, indicating lights, CTS contactors, A/M Switch for remote controls operation complete as per specifications and drawings and as required.The panel manufacturer shall have min 70 KA CPRI Certification
340	Incomer
341	1 Nos. 260-300 Amps 36 KA MCCB TP+NL with ROM & Links
342	1 No. 400 Amps aluminium conductor bus bar duly sleeved
343	1 No. Multifunction meter with CTs as per requirment
344	3 Nos. phase indicating lamps
345	Outgoing
346	50 Nos MCB suitable for 1.1 to 3.7 KW or suitable DOL Starter for AHU having contactors, LED indicators for on/off , O/L Relay, SPP, etc. as per coordination chart
347	6 Nos MCB suitable for 5.5 to 7.5 KW or suitable DOL Starter for AHU having contactors, LED indicators for on/off , O/L Relay, SPP, etc. as per coordination chart
348	1 Nos MCB TPN 32 Amps 'C\\" Curve Spare and complete Wiring inclusive of thimbles,etc
349	Hardware (PVC Cahnnels/MCB Channels/Fibre- Glass Gaskets/ Sleevs/ nuts/ bolt/ washers/ cooling fans etc Including complete wiring, thimbles etc.
350	Unloading at site, placement of Panel on the foundation, co-ordination during execution, rendering necessary guidance for execution, supervision, testing, commissioning and startup of above mentioned Panel.The panel drawing shall be approved before taking up the fabrication from EIC
351	(Make: As per approved make list attached)
352	Ventilation
353	S/I/T/C of CEILING MOUNTED JET VENT FAN
354	Supply, installing, testing and commissioning of Ductless Ventilation / Axial type Jet fans as per attached specifications for normal ventilation & smoke exhaust . Each fan shall be complete with dual speed motor and die cast aluminium impeller. Casing shall be made of Hot dipped Galvanized steel. The Motor shall be run on the electrical power suitable for 415V/3Ph/ 50Hz.
355	Supply, installing, testing and commissioning of Ductless Ventilation / Jet fans as per Specifications for Normal Ventilation and Smoke Exhaust. . The complete fan assembly with its casing, impeller and motor ( not only motor or one of the item ) shall be sourced from one manufacturer and certified and tested as per EN12101-3-:2015/Indian Standared as per NBCC, 300 degree for 2 Hrs operation.Silencer lenght should be 2 d. . Each Jet Fan assembly shall connect to a composite PLC Panel controlled by CO Sensors / Fire Alarm System for Smoke Extraction Dia of fan 315 mm or suitable dia
356	(Make: As per approved make list attached)
357	S/I/T/C of LONG CASED TUBE/ VANE AXIAL FAN WITH IE3 MOTOR
358	Supply, installation, testing and commissioning of Direct drive Long cased Tube/ VANE Axial fans complete with Hot dipped Galvanised Steel /Pre Galaavanised Steel Casing with spun flanges, adjustable pitch die cast aluminium impeller (Hub and Aerofoil blades) and IE3 motors. Casing position shall be as per the job requirement and shall be marked on the fan assembly.The complete fan assembly with its casing, impeller and motor ( not only motor or one of the item ) shall be sourced from one manufacturer and 300 degree C for 2 Hrs operation.The complete assembly must have certificate of consistency of performance by BSI .Motor Shall be suitable for 415 volts ± 10%, 50Hz ± 3 %, three phase A.C complete with starter having overload & single phase protection, support, mountings, vibration isolators, fire retardant flexible canvass connector 150 mm deep (Inlet & Outlet as required), bird screen (Inlet & Outlet as required), Including cost of Back draft Damper,Exhaust Louvers , : Fan must be licensed to bear AMCA seal for air performance and sound performance ad the claimed air and sound performance must be demonstrated in AMCA accredited laboratory as per AMCA publication 211 and 311
359	Supply, installing, testing and commissioning of Single speed Long cased VANE Axial Fans of capacity 9600cfm @ 25 mm Static (for normalmode) Fans should be suitable for emergency mode operation (300 Deg / 2 Hrs)
360	(Make: As per approved make list attached)
361	S/I/T/C of LONG CASED TUBE /VANE AXIAL FAN WITH IE3 MOTOR (FOR FRESH AIR)
362	Supply, installation, testing and commissioning of Direct drive Tube VANE Axial fans complete with Hot dipped Galvanised Steel /Pre Galvanised/ MS Powder coated Casing with spun flanges, adjustable pitch die cast aluminium impeller (Hub and Aerofoil blades) and IE3 motors. Casing position shall be as per the job requirement and shall be marked on the fan assembly.The complete fan assembly with its casing, impeller and motor ( not only motor or one of the item ) shall be sourced from one manufacturer.MotorShall be suitable for 415 volts ± 10%, 50Hz ± 3 %, three phase A.C complete with starter having overload & single phase protection, support, mountings, vibration isolators, fire retardant flexible canvass connector 150 mm deep (Inlet & Outlet as required), bird screen (Inlet & Outlet as required) and including cost of Back draft damper ,GI construction fresh air louvers with min. 60 % free area , and painted in baked enamel shade with metallic frame work complete as per specification approved drawings and schedules. Louvers need to be suitable in order avoid rain water entry in to spaces @ 15 degree deflection with bird screen complete as per specification approved drawings and schedulesetc. & of following capacity. Fan must be licensed to bear AMCA seal for air performance and sound performance ad the claimed air and sound performance must be demonstrated in AMCA accredited laboratory as per AMCA publication 211 and 311.
363	Supply, installing, testing and commissioning of Single speed Long cased VANE Axial Fans of capacity 9600cfm @ 25 mm Static (for normalmode) Fans should be suitable for emergency mode operation (250 Deg / 2 Hrs)
364	(Make: As per approved make list attached)
365	S/I/T/C OF CO SENSORS
366	Supply, installation, testing and commissioning of CO Sensors (0 - 250 PPM detection Range) complete with hanging arrangments. (Make: As per approved make list attached)
367	CFD Analysis
368	Preparation and approval of CFD ( Computational Fluid Dynamics ) Analysis in Basement Areas ( both levels) .CFD analysis to decide the correct location and quantity of jet fans. CFD analysis will be carried out for both normal and fire mode ventilation situation considering 6/12 ACPH, airflow strategy and control strategy to confirm the operation logic. CFD analysis will model all the cars, car parking bays, beams, structures, columns, voids, shafts, ramps, proposed fresh air route, fresh air shaft, exhaust air shaft and preliminary location of jet fans shown in the drawing. CFD output will give complete simulation of ventilation scheme not limited to velocity profile, temperature profile, smoke temp and movement profile, CO level profile, air movement profile. The number of repeat simulations shall be carried out until satisfactory results are achieved.
369	Control Panel for Ventilation PLC Based
370	Supply,Installation,Testing and Commissioning Contol Panel Made out of TATA/SAIL/ESSAR/JINDAL/Reputed make sheet having thickness 2.0 mm for load bearing surfaces & 1.6 mm Non bearing surfaces duly processsed powder coated having Siemens grey colour as per following specifications complete in all respect
371	SITC of Electrical cum PLC Based Panel for Basement with MCB feeders with starters for 8 nos dual speed 3 phase Jet Fan fans of 1.7/0.34 kW each,MCCB feeders with starters for 4nos. Exhaust fans single speed of upto 7.5KW & 4 No Fresh Air Fan of upto 7.5 kw(optional). controlled by nos- upto 5 NO CO Sensors, with suitable incomer MCCB, VIF Meter on mains & on each feeder herein referred to as each O/G section to Jet fans as well as Exhaust with Amperemeter Digital, aluminium bus bar as per requirment, PLC logic controller with necessary internal control wiring etc, Material Make of Switchgear:ABB/ Schneider/ Siemens
372	(Make: As per approved make list attached)
373	Staircase,Lift Lobby & Lift Pressurisation Fans
374	Supply, Installation testing & Commissioning of AXIAL FLOW FAN complete with totally enclosed fan cooled motor direct driven, and fan shaft, motor mount as per the specifications. Fan motor shall be Class-F, suitable for 415 + 10% volts, 50 cycles, 3 phase power supply. The Axial fans shall be supplied with power pane. Fan capacity shall be as follows:
375	Casing shall be GI/hot dip galvanized to protect against corrosion. Length of the casing shall be greater than the length of fan & motor assembly.IMPELLER of axial fans shall be constructed from die cast aluminum. Profiles of impeller blade should be of aerofoil type to have high efficiency and low noise levels. Impeller must be statically and dynamically balanced as per ISO 1940 grade 6.3. Fan shall be selected based on best efficiency points with fan pitch angle selected in the middle range out of available whole range of fan pitch angle to allow possible fan speed adjustment on site.
376	Liftwell Pressurisation Axial Fan 17300cfm x 20mm sp
377	Staircase Pressurisation Axial Fan 23000 cfm x 25mm sp
378	Lift Lobby Pressurisation Axial Fan 2500 cfm x 20mm sp
379	Lift Lobby Pressurisation Axial Fan 5000 cfm x 20mm sp
380	(Make: As per approved make list attached)
381	SITC of Starter Panels- Supply /Exhaust Air Blower up to 7.5 KW)
382	01 No. - 0-40 A TP MCB with Conforming to BIS 25 A DOL starter, overload relay, start/stop push buttons, ammeter (0-63A) on / off / trip indication lights with protection fuse, single phase preventer
383	Star Delta starter control panel must have MCB TPN, on off push button, on/off/trip indicators, potential free contacts for Fire Alarm for operation of the starter in case of fire, manual reset overload relays, earthing & armoured fire proof cabling from starter panel to fan motor with proper tray supports & BMS compatible. Starter panel with auto manual toggle switch,Timer based & facility to operate on remote signal from smoke control panel .
384	CABLING (POWER
385	Power Cabling and Earthing
386	Supply, installation, testing & commisioning of Aluminum/CU conductor cables PVC sheathed, armoured cables of 1.1 KV grade with termination glands and GI earthing, identification tags, clamps and saddles etc.
387	3.5Cx300 Sqmm Al
388	3.5Cx240 Sqmm Al
389	3.5Cx150 Sqmm Al
390	3.5C x70 Sqmm Al
391	4C x35 Sqmm Al
392	4.0Cx16 SqmmAl
393	4.0Cx10 Sqmm Al
394	4.0Cx 06 Sqmm Al
395	4.0Cx04 Sqmm CU
396	4.0Cx2.5 Sqmm CU
397	2Cx04 Sqmm (Cu Conductor flexible)
398	(Make: As per approved make list attached)
399	Control Cabling
400	Supply, installation, testing & commisioning of Copper conductor , PVC insulated, PVC sheathed armoured cable of 1.1 KV grade (Which is Interconnecting wiring for the fire alarm system with the AHU and the smoke dampers and AHU to Control Consol Panel
401	8C x 1.5 Sqmm
402	3C x 1 Sqmm
403	2C x 1 Sqmm
404	(Make: As per approved make list attached)
405	Supply, Laying, testing and commissioning of FRLS XLPE armoured cables for Electrical Power and controls from MCC/LSCP/PDB to respective Equipments with earthing, clamped on surface or on cable trays, structural supports and cable supports provided. The scope includes End Termination of cables with Double Compression type Brass Cable Glands and Copper Lugs, clamping of cables by ready made G.I. spacers, saddles or clamps fabricated out of GI. strip 3 mm thick, treasing and Clamping of Cable on cable tray or surface, supply of all clamping materials and hardware etc., providing cable tags made out of aluminium/PVC laminated strip and 75x20 mm in size with cable number and size punched on it. Cable tags shall be tied to cables at every 20 meter interval and at both the ends. MS Powder Coated Junction Boxes with Bolted type terminals of suitabel size shall be provided near all Fan Motors for termination of armoured cables.
406	4C x 6 Sqmm Copper Cable ( For Fire Exhaust Fans)
407	4C x 1.5 Sqmm Copper Cable ( For Jet Fans )
408	Supply & laying of XLPE armoured copper conductor twisted shielded control cables 3C X 1.5 Sq.mm twisted shielded cables for CO sensors.
409	(Make: As per approved make list attached)
410	Under Deck Insulation
411	Providing & Fixing Underdeck Insulation with 50 mm thick TF Quality EPS of Density 20 Kg/M3 fixed to slab with good quality Black CPRX Compound. 28Gwirenet shall be tightened arround insulation so as avoid any kind of sagging, Ends of net shall be overlapping at least 25mm. Overlaps shall be screwed with galvanized screws to avoid rusting : (Make: As per approved make list attached)
412	SENSORS AND FIELD DEVICES
413	Differential Pressure Transmitter for OT Positive Pressure control (15 Pascal set point) complete with wall mounted fixtures / two side Tubing complete having measurement accuracy up to 0.05% or better
414	SITC Of Duct type temperature & RH sensor with +-2% Accuracy
415	CABLES
416	Supplying, installing, testing and commissioning of 2 Core X 1.0 Sqmm Shielded Flexible Copper Cable (per I/O points hard wired to DDC).
417	Supplying, installing, testing and commissioning of 4 Core X 1.0 Sqmm Shielded Copper Cable (per Soft I/O points to DDC).
418	Supplying, installing, testing and commissioning of 2 Core X 1.5 Sqmm Shielded Flexible Copper Cable (per DDC to Integrator).
419	Supplying, installing, testing and commissioning of CAT -6 Cable (per DDC to Integrator).
420	DSR 2025 (E&M) Items
421	Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.
422	Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required
423	Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.
424	Providing and fixing 6 SWG dia G.I. wire on surface or in recessfor loop earthing along with existing surface/ recessed conduit/submain wiring/ cable as required.
425	Providing and fixing earth bus of 50 mm X 5 mm copper strip on surface for connections etc. as required
426	Hot dipped Galavnised Iron Cable Tray
427	Supplying & installing following sizes of perforated Hot Dipped Galavanised Iron cable tray (Galavnisation thickness not less than 50 microns) with perfoaration more than 17.5 % in convenient sections, joined with connectors, suspended from ceiling with GI suspenderes including GI Bolts & nuts etc. as required (U Shaped Tray)
428	450mm(W) x50 mm(D) and 2.0 mm Thickness
429	300mm(W) x 50 mm(D) and 1.5 mm Thickness
430	150mm(W) x 50 mm.(D) and 1.5 mm Thickness
431	Supplying & installing following sizes of perforated Hot Dipped Galavanised Iron cable tray\\"bends\\" (Galavnisation not less than 50 microns) with perfoaration not more than 17.5 % in convenient sections, joined with connectors, suspended from the ceiling with GI suspenders including GI Bolts & nuts etc. as required
432	450mm(W) x50 mm(D) and 2.0 mm Thickness
433	300mm(W) x 50 mm(D) and 1.5 mm Thickness
434	50mm(W) x 50 mm.(H) and 1.5 mm Thickness
435	CHILLED WATER PIPING
436	Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled water piping plumbing inside the building (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.),cut to required length, and installed with welded joints (USE RECTIFIER AS SPECIFIED), duly insulated with fire retardant quality expanded polystrene moulded pipe section of density 20 kg/cu.m after a thick coat of cold setting adhesive (CPRX compound) wrapping with 500g polythene faced hessain and finally applying 0.63mm aluminium sheet cladding complete with type3, grade 1 roofing feltstrip(as per IS:1322 as amended up to date) at joints repairing of damage to building etc. as per specifications and as required complete in all respect.
437	Note:-The Pipes of sizes 150 mm & below shall be M.S. ‘C’ class as per IS : 1239 and pipes size above 150 mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35 mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum 7mm thick MS sheet for pipes of 400 mm dia and above.(Make: As per approved make list attached)
438	200 MM Pipe DIA with 75 mm Thick Insulation
439	150 MM Pipe DIA with 75 mm Thick Insulation
440	125 MM Pipe DIA with 50 mm Thick Insulation
441	100 MM Pipe DIA with 50 mm Thick Insulation
442	80 MM Pipe DIA with 50 mm Thick Insulation
443	65 MM Pipe DIA with 50 mm Thick Insulation
444	50 MM Pipe DIA with 50 mm Thick Insulation
445	40 MM Pipe DIA with 50 mm Thick Insulation
446	32 MM Pipe DIA with 50 mm Thick Insulation
447	25 MM Pipe DIA with 50 mm Thick Insulation
448	(Make: As per approved make list attached)
449	SITC of Insulated VALVES/CONTROLS - PN-16 including cost of MS Flanges as per the Table(Make: Advance, Sant, Zoloto)
450	Supplying, fixing, testing and commissioning of following valves, strainers, gauges in the chilled water plumbing duly insulated to the same specifications as the connected piping and adequately supported as per specifications.
451	BUTTERFLY VALVE (MANUAL) with C I body SS disc nitrile sheet & O - ring & PN 16 pressure rating for chilled water /hot water circulation as specified.
452	200 MM DIA
453	150 MM DIA
454	125 MM DIA
455	100 MM DIA
456	80 MM DIA
457	65 MM DIA
458	50 MM DIA
459	BALANCING VALVE WITH BUILT IN MEASURING FACILITY with C I body flanged construction with EPDM coated disc with long pitch with protected out pipe insulation & PN 16 pressure rating for chilled / hot water circulation as specified.
460	150 MM DIA
461	125 MM DIA
462	100 MM DIA
463	80 MM DIA
464	65 MM DIA
465	50 MM DIA
466	NON - RETURN VALVE with duel plate of C I body SS plates vulcanized NBR seal flanged end & PN 16 pressure rating for chilled / hot water circulation including insulation as specified.
467	150 MM DIA
468	80 MM DIA
469	Y - STRAINER of Ductile CI Body flanged ends with stainless steel strainer for chilled / hot water circulation including insulation as specified.
470	150 MM DIA
471	80 MM DIA
472	65 MM DIA
473	50 MM DIA
474	Providing & Fixing in position the industrial type pressur gauges with gun metal/brass valves complete as required
475	(Make: As per approved make list attached)
476	Providing & Fixing in position the mercury in glass industrial type thermometers
477	(Make: As per approved make list attached)
478	CONDENSOR WATER PIPING
479	Supplying, fixing, testing and commissioning of condenser water pipes of following sizes of MS 'C' class along with necessary clamps, vibration isolators and fittings such as bends,tees etc.but excluding valves, strainers, gauges etc. adequately supported on rigid supports duly painted/buried in ground excavation and refilling etc. as per specification and as required complete in all respect.
480	Note:-i)The Pipes of sizes 150 mm & below shall be M.S. ‘C’ class as per IS : 1239 and pipes size above 150 mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35 mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum 7mm thick MS sheet for pipes of 400 mm dia and above. ii) For under ground pipe : The pipe will be covered by applying 2-4mm thick Tarfelt sheet with required Adhesive, Accessories etc
481	250 MM DIA
482	200 MM DIA
483	(Make: As per approved make list attached)
484	VALVES/CONTROLS - PN-16 without Insulation , Make :Advance, Sant, Zoloto
485	Supplying, fixing, testing and commissioning of following valves, gauges and strainers for condenser water circulation as per specifications.
486	BUTTERFLY VALVE (MANUAL) with C I body SS disc nitrile sheet & O - ring & PN 16 pressure rating as specified.
487	200 MM DIA (Gear Box type)
488	NON - RETURN VALVE with duel plate of C I body SS plates vulcanized NBR seal flanged end & PN 16 pressure rating for chilled / hot water circulation as specified.
489	200 MM DIA
490	Ducting
491	Supply, installation, balancing and commissioning of fabricated at site GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, Splitler dampers,vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required and shall also confirm to the BIS specifications.
492	Thickness 0.63 mm sheet
493	Thickness 0.80 mm sheet
494	Thickness 1.00 mm sheet
495	Supply, installation, balancing and commissioning of fabricated at site GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, Splitler ampers,vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required and shall also confirm to the BIS specifications.
496	Thickness 0.63 mm sheet
497	Thickness 0.80 mm sheet
498	Thickness 1.00 mm sheet
499	(Make: As per approved make list attached)
500	Grilles/Diffusers/Dampers

Tender Documents

SR No	FileName	File Description
1	Click here to download tender document	Tender Documents
2	Click here to download tender document	Tender Documents
3	Click here to download tender document	Tender Documents
4	Click here to download tender document	Tender Documents

Also Visit

Tenders

Chandigarh Tenders

Distribution and Conditioning Tenders

Air Conditioning Tenders

HVAC Tenders

Disclaimer

We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.

Top

Tender For Revised Dnit Providing Installing Testing Commissioning And Handing Over Of Hvac System For Setting Up Of Mother And Child Care Centre At Block K, Sector - 32A, Chandigarh. (Including 5 Years Operation, Running & Comprehensive Maintenance, Chandigarh-Chandigarh

Tender Documents

Disclaimer

About Us

Services

Browse Tenders

For Sales Inquiry

Tender For Revised Dnit Providing Installing Testing Commissioning And Handing Over Of Hvac System For Setting Up Of Mother And Child Care Centre At Block K, Sector - 32A, Chandigarh. (Including 5 Years Operation, Running & Comprehensive Maintenance, Chandigarh-Chandigarh

Tender Documents

Disclaimer

OTP Verification

About Us

Services

Browse Tenders

For Sales Inquiry

Connect With Us