|
| 1 | (a) (Building wk)Guard Room:-M & L for dismantling Asbestos cement sheet roofing including ridges, hips, valleys and gutters etc.,and stacking the material within 50 metres lead |
| 2 | Free for fixing of PPGI profile Sheet of 0.50mm (+0.05%) total coated thickness with zinc coating 120 gm per sqm in 240 mpa steel grade as free for fixing, using self drilling/ self tapping screws of size 5.5x55mm with EPDM seal, complete to the existing truss and purlins etc complete. |
| 3 | Providing and fixing PPGI sheet ridges or hips of width (500- 600mm) overall width plain sheet of 0.50 mm (+0.05%) total thickness , zinc coating fixed 120grms per sqm as per IS :277 using self drilling or self tapping screws complete. |
| 4 | Dismantling cement asbestos sheets or other hard board in ceiling , including stacking of serviceable materials and disposal of unserviceable materials within 50 metres lead. |
| 5 | Dismantling wood work in frames, trusses, purlins and rafters up to 10 metres span and 5 metres height including stacking the material within 50 metres lead. |
| 6 | Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum moisture resistant board |
| 7 | Dismantling of old plaster or skirting raking out joints and cleaning the surface for plaster incl disposal of rubbish to the dumping ground within 50 mtr lead. |
| 8 | Repair to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sqm and under incl cutting the patch in proper shape, racking out joints and plastering the surface of the walls, including disposal of rubbish to the dumping ground within 50m lead etc. complete with CM 1:4( 1 cement : 4 coarse sand). |
| 9 | Providing and finishing with two or more coats applied @ 1.43 ltr/10 Sqm over existing cement paint surface Premium Acrylic smooth exterior paint with silicon additives of required shade including removing of old water proofing cement paint by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc complete. |
| 10 | Distempering with oil bound washable distemper approved brand and manufacturer to given an even shad in old work (one or more coats) incl preparation of old surface by removing old paint by scrapping, sand papering incl necessary repairs to scratches etc complete. |
| 11 | Dismantling doors, windows shutters including chowkhats, holdfasts etc complete of area 3 sqm and below. |
| 12 | Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc as required in door frame and guard bars. |
| 13 | Providing and fixing factory made steel glazed windows and ventilators , side/top/centre hung , with beading and all members such FD7,F4B,K11B etc, including providing and fining hinges, pivots, including priming coat of approved steel primer of fixing with 15x3mm lugs 10cm long embeded in cement concrete block 15x10x10cm of cement concrte (1:3:6). |
| 14 | Providing and fixing fly proof wire gauge to windows, doors and ventilators with MS flat 15x3mm and nuts & bolts complete of 0.63mm dia wire and 1.4 aperture on both sides. |
| 15 | Providing and fixing glass panes with putty and glazing clips in steel doors, windows and ventilators all complete with 4mm thick glass panes. |
| 16 | Providing and fixing of mosquito proof shutters using galvanized MS wire gauge of average width of aperature 1.4mm in both directions with wire of dia 0.63mm for door of 35mm with 2nd class teak wood. |
| 17 | Providing and fixing ISI marked oxidised M.S. pressed butt hinges with necessary screws etc. complete. 125x65x2.12 mm |
| 18 | Providing and fixing aluminium handles of size : 125 mm, transparent or dyed to required colour or shade, with necessary screws etc. complete |
| 19 | Providing and fixing aluminium tower bolts of size : 200x10 mm with necessary screws etc. Complete. |
| 20 | Providing and fixing aluminium tower bolts of size : 150x10 mm with necessary screws etc. Complete. |
| 21 | Supply and fixing aluminum sliding door bolts, transparent or dyed to required colour or shade, with nuts and screws etc complete of size 300x16mm. |
| 22 | Rewiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable and 1.5 sq.mm FRLS PVC insulated copper conductor single core cable as earth wire in existing surface/ recessed steel/PVC conduit including dismantling as required. Group A |
| 23 | Supplying and fixing following piano type switch/ socket on the existing switch box/ cover including connections etc. as required.5/6 amps switch |
| 24 | Supplying and fixing following piano type switch/ socket on the existing switch box/ cover including connections etc. as required. 3 pin 5/6 A socket outlet |
| 25 | Supplying and fixing following piano type switch/ socket on the existing switch box/ cover including connections etc. as required. 15/16 A switch |
| 26 | Supplying and fixing following piano type switch/ socket on the existing switch box/ cover including connections etc. as required. 6 pin 15/16 A socket outlet |
| 27 | Supplying and fixing brass batten/ angle holder including connection etc. as required. |
| 28 | Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required. |
| 29 | Supply and fixing stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required. |
| 30 | Supplying and fixing following rating, double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 A |
| 31 | Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required 6 ways. (But without MCB/RCCB/Isolator) |
| 32 | Supply and fixing 5 amps to 32 amps rating, 240/415 volts, \\"C\\" curve, miniature circuit breaker suitable for inductive load of single pole in the existing MCB DB complete with connections, testing and commissioning etc. as required. |
| 33 | Riflewomen Barrack:-Providing and fixing factory made uPVC door frame made of uPVC extruded sections having an overall dimension as below (tolerance ±1mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame to be Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer’s specification and direction of Engineerin- charge Extruded section profile size 48x40 mm |
| 34 | Providing and fixing factory made 30 mm thick door shutter made of solid PVC foam profile. The styles & rails shall be of size 75 mm x 30 mm having wall thickness 5 mm. The styles, top & bottom rails shall have one side wall thickness of 15 mm integrally extruded on the hinge side of the profile for better screw holding power. The styles and rails shall be reinforced with M.S. tubes of size 33 mm x 17 mmx 1 mm, painted with primer , all four corners of reinforcement to be welded or sealed. Solid PVC extruded bidding (push fit type) will be set inside the styles and the rails with a cavity, to receive single piece extruded 5mm PVC sheet as panel. The styles and rails will be mitred cut and joint with the help of PVC solvent cement & self driven self tapping screws. Single piece extruded solid PVC lock rail of size 100 mm x 30 mm with wall thickness 5 mm & 15 mm integrally extruded in the middle of the lock rail & fixed with styles with the help of PVC solvent cement & self driven self tapping screws of size 100mm x 8 mm complete as per manufacturer's specifications and direction of Engineer-in-charge. Non decorative finish |
| 35 | Providing and laying non skid ceramic floor tiles of size 300x300mm ( thickness to be specified by the manufacturer) of approved make, in all colours and shades except white, Ivory, Grey laid on 20mm thick CM 1:4 (1cement :4 coarse sand), incl grouting the joints with white cement and matching pigments. etc. complete. |
| 36 | Providing and laying of ceramic glazed wall tiles of size 200x300mm of approved make in all colours of any size in walls/skirting or dados over 12 mm thick bed of CM (1:3) and jointing with grey cement slurry @ 3.3 kg per sqm incl pointing the joints with white cement complete. |
| 37 | Providing and fixing aluminium handles of size : 125 mm, transparent or dyed to required colour or shade, with necessary screws etc. complete |
| 38 | Providing and fixing aluminium tower bolts of size : 100x10 mm with necessary screws etc. Complete. |
| 39 | Providing and fixing of 15mm nominal bore CP bib cock of approved quality. |
| 40 | Providing and fixing white vitreous pedestal type china wash hand basin (Size 630x450 mm) incl pedestal with C.I. Brackets, 15 mm C.P Brass pillar taps, 32 mm C.P. Brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required etc. complete. |
| 41 | Providing and fixing 32 mm dia flexible P.V.C waste pipe for sink or wash basin including P.V.C waste fittings complete. |
| 42 | Providing and fixing 600x450mm beveled edge mirror of superior glass ( of approved quality) complete with 6 mm thick hard board backing fixed to wooden cleats with CP brass screws and washers complete.. |
| 43 | Providing and fixing of 100mm dia CP brass shower rose with 15 or 20mm inlet of approved quality. |
| 44 | Providing and fixing of 15mm nominal bore CP angle cock of approved quality. |
| 45 | Providing and fixing of 15mm nominal bore connection pipe of approved quality. |
| 46 | Providing and fixing 100 mm sand cast Iron grating for gully trap |
| 47 | Providing and fixing on wall unplasticised rigid PVC pipes incl jointing with seal ring, single socketed pipes of 75 mm dia. Please Enable Macros to View BoQ information |
