Tender For Construction Of Institute Of Driving Training And Research (Idtr Tier-1) At Jamshedpur, East Singhbhum, East Singhbhum-Jharkhand

TDR : 56019903

Tender Notice
BOQ

14 Days Left

East Singhbhum , Jharkhand

Tender Brief : Tender For Construction Of Institute Of Driving Training And Research (Idtr Tier-1) At Jamshedpur, East Singhbhum

Document Fees
₹ 10000 /-

EMD
₹ 2016000.0 /-

Tender Value
Refer document

Submission Date
07-07-2026

Competition Type
Indian

Bidding Type
Tender

Need a Business Loan? Apply Now !


1	Earth work in excavation in foundation trenches in ordinary soil ( vide classification of soil item A) and disposal of excavated earth as obtained to a distance upto 50M including all lifts leveling ramming the foundation treanches, removing roots of trees, and shrubs all complete as per approved design, building specification and direction of E/I.
2	Extra for earthwork in hard soil as per specification and direction of E/I. ( vide classification of soil item-B)
3	Earth filling in foundaion trenches and plinth in layers not exceding 150 mm thick well watered, rammed, fully compacted and fine dressed with earth obtained from excavation of foundation trenches within a lead of 50 M and lift of 1.5 M all complete as per building specification and direction of E/I. (mode of measurement compacted volume)
4	Filling in foundation trenches and plinth in layers. Not exceeding 150 mm thick well watered, rammed fully compacted and fine dressed with earth obtained after cutting within a lead of 50 M and lift of 1.5 M all complete as per building specification and direction of E/I (Mode of measurement compacted volume)
5	Providing coarse clean sand in filling in in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials labour, royalty and taxes all complete as per building specification and direction of E/I (Mode of measurement compacted volume)
6	Providing designation 75A brick work in C.M (1: 6) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar, joints cost of screening materials raking out joints to 15mm depth , curring , taxes and royalty all complete as per builiding specification and direction of E/I.
7	Providing designation 75B brick work in C.M (1:6 ) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar, joints cost of screening materials raking out joints to 15mm depth , curring , taxes and royalty all complete as per builiding specification and direction of E/I.
8	Providing designation 75 A brick work in C.M. (1: 6) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including, providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth curing, taxes and royalty all complete as per building specification and direction of E/I.
9	Providing designation 75 B brick work in C.M. (1:6) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including, providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth curing, taxes and royalty all complete as per building specification and direction of E/I.
10	Providing designation 125 mm thick reinforced designation 75A brick work in CM (1:4) in superstructure with approved quality of clean coarse sand of F.M. 2 to 25 including the cost of screening, carriage of materials, scaffolding , raking out joints to 15mm depth, curing, taxes and royalty (but excluding the cost of reinforcement) all complete as per building specification and direction of E/I.
11	Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :
12	1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)
13	1:2:4 (1 Cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 40 mm nominal size)
14	1:3:6 (1 Cement : 3 coarse sand (zone-III) : 6 graded stone aggregate 20 mm nominal size)
15	1:3:6 (1 Cement : 3 coarse sand (zone-III): 6 graded stone aggregate 40 mm nominal size)
16	1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size)
17	Providing and laying cement concrete in retaining walls, return walls,walls (any thickness) including attached pilasters, columns, piers,abutments, pillars, posts, struts, buttresses, string or lacing courses,parapets, coping, bed blocks, anchor blocks, plain window sills, fillets,sunken floor,etc., up to floor five level, excluding the cost of centering,shuttering and finishing :1:1½:3 (1 cement:1½ coarse sand:3 graded stone aggregate 20 mm nominal size)
18	Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.
19	Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level. 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size)
20	Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mmnominal size)
21	Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).
22	Centering and shuttering including strutting, propping etc. and removal of form for
23	Foundations, footings, bases of columns, etc. for mass concrete
24	Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.
25	Suspended floors, roofs, landings, balconies and access platform
26	Lintels, beams, plinth beams, girders, bressumers and cantilevers
27	Columns, Pillars, Piers, Abutments, Posts and Struts
28	Stairs, (excluding landings) except spiral-staircases
29	Weather shade, Chajjas, corbels etc., including edges
30	Supplying, fitting and fixing 35mm thick solid core type decorative single leaf flush door shutter with both sides decorative veneered with black board core bended with high quality phenol formal dehydes synthetic resine of standard make with Aluminium fittings such as hinges, towerbolts, handle, cleat and sand blocks and taxes all complete as per building specification and direction of E/I.
31	Supplying, fitting and fixing 35mm thick solid core type decorative double leaf flush door shutter with both sides decorative veneered with black board core bended with high quality phenol formal dehydes synthetic resine of standard make with Aluminium fittings such as hinges, towerbolts, handle, cleat and sand blocks and taxes all complete as per building specification and direction of E/I.
32	providing Tor steel reinforcement of 8mm dia rods as per approved design and drawing exclusive carriage of M.S. bars to work site, cutting, bending and binding with annealed wire with cost of the wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I. TMT Fe 500 (only valid for SAIL & TATA STEEL)
33	providing Tor steel reinforcement of 10mm,12mm,& 16mm. dia bars as per approved design and drawing inclusive carriage of M.S. bars to work site, cutting, bending and binding with annealed wire with cost of the wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I.
34	(a) 10mm (TMT coil Fe 500) (only valid for Tata (Tiscon), SAIL, JSPL,Electrosteel Steels Ltd. Bokaro and Vizag (RINL)}
35	(b) 12mm (TMT coil Fe 500) (only valid for Tata (Tiscon), SAIL, JSPL,Electrosteel Steels Ltd. Bokaro and Vizag (RINL)})
36	Supplying, fitting, and fixing M.S. Grill made of 20X6mm M.S. Flate as per approved design and drawing, properly fabricated with joints continuous fillet welded and finished smooth, carriage of grill to work site, hoisting as per building specification and direction of E/I. (where materials is not supplied by the deptt.)
37	Supplying, and fixing fan hook of 16mm dia M.S. bar 1 meter long bent to required size and shape , placed in position and fixed in R.C.C. slab/beam at the time of casting all complete as per building specification and direction of E/I. (where materials is not supplied by the deptt.)
38	Supplying, fitting and fixing collapsible gate of approved size and make properly fabricated with vertical double channels 20 x 10 x 2mm at 100mm centers and braced with M.S. flat diagonals 20 x 3mm with top and bottom rails of T.iron 40 x 40 x 6mm with 38mm dia steel pulleys complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of red lead paint, car riage, hoisting and taxes all complete as per building specification and direction of E/I.
39	Supplying, fitting and fixing 20mm dia M.S. Bar 1 meter long holding down bolt with nuts washers 100 X100 X6mm plate fitted and fixed with cement concrete (1:24) as per approved design all complete as per building specification and direction of E/I.
40	Supplying, fitting and fixing 20 guage G.C.I. Sheet gate fitted on M.S. Angle frame of size 60X60X6mm. Including cost of fabrication, providing necessary locking arrangement with haskal and domny duly fixed in P.C.C. (1:2:4) blocks of required size applying a priming red lead paint over steel work, taxes all complete as per drawing specification and direction of E/I.
41	Supplying, fitting and fixing M.S. grill gate with M.S. grill made of 20X6mm M.S. flats or 16mm M.S. square bars fitted on 25X25X6mm M.S. Angle frame of size 60X60X6mm. Including cost of fabrication, providing necessary locking arrangement with haskal and domny duly fixed in P.C.C. (1:2:4) blocks of required size applying a priming red lead paint over steel work, taxes all complete as per drawing specification and direction of E/I.
42	Providing designation 75A one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/I.
43	Providing designation 75A one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/I.
44	Providing average 150mm thick dry rammed khoa beaten to112mm.(compacted with water) made of well burnt or jhama bricks including ramming properly till compacted thckness is achieved, curing and carriage of water with all leads,making proper slope and blending the top with cement morter (1:10) all complete as per building specification and direction of E/I
45	Providing 25mm thick first class patent stone flooring (1:2:4) with stone chips in two layers, bottom layers 19mm. Thick (1:2:4)with 12mm to 6mm. Size graded stone chips and top layer 6mm. Thicks (1:2) with 6mm down stone chips, in panels including cost of curing, finishing the surface smooth by rubbing with carborandum stone, taxes and royality with all complete as per building specification and direction of E/I.
46	Providing and laying 25mm thick kotah stone slab flooring of approved size texure and colour over 19mm thick base of lime mortar (1:1:1) (limeputty:surkhi:coarse sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing to granolithic finish with approved quality of carborandum stone including cost of curing, taxes and royalty all complete as per building specification and direction of E/I. :(iii) 450X450 mm size
47	Providing and laying 25mm thick kotah stone tiles in risers of steps skirting and pillars of approved size texure and colour laid over 12mm thick cement mortar (1;30 and joined with grey cement slurry mixed with pigment to match the shade of the slab including rub bing to granolithic finish with approved quality of carborandum stone including cost of curing, taxes and royalty all complete as per building specification and direction of E/I.
48	Providing and laying 25mm thick white makrana marble stone slab flooring of approved quality over 19mm thick base of lime mortar (1:1:1) (Lime putty: surkhi: coarse sand) laid and joined with white cement slurry including rubbing and polishing to granolithic finish with approved quality of carborandum stone including cost of curing, taxes and royalty all complete as per building specification and direction of E/I. :(i) 300X300 mm size
49	Providing and laying 6mm precast white glazed tiles in walls over 12mm cement mortar (1:3) and jointed with grey cement slurry flush pointing with white cement including rubbing, polishing and cost of curring taxes and royalty all complete as per building specification and direction and E/I. : With \\"A\\" grade white 15X15cm Tiles.
50	Providing and laying vitrified Paring / Industrial tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 4457:2007, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 300x300 x 10 mm sizes.
51	For StairProviding and laying vitrified floor tiles for step of stair in with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete step tiles & have bullnose, Anti and self embossed line. Size of Tile 1200x300 mmx15 mm
52	Providing and laying Doublecharge vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622 / ISO 13006 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm .
53	Providing 12mm cement plaster (1:3) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.
54	Providing 12mm cement plaster (1:4) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.
55	Providing 12mm cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.
56	Providing 6mm cement plaster (1:4) in celling with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.
57	Providing 1.5mm cement punning including curing, carriage of water with all leads and lift as per building specification and direction of E/I.
58	Providing 25mm thick water proof cement plaster (1:3) with clean coarse sand of F.M. 1.5 with 5% cico or any other approved water proofing compound including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.
59	Providing two coats of oil bound distemper of approved shade and make over a coat of cement primer over new surface including preparing the plastered surface by the rubbing smooth with pumice stone or fine sand paper applying putty wherever required scaffolding washing of floors and taxes all complete as per building specification and direction of E/I.
60	Providing two coats of plastic emulsion paint of approved shade and make over old surface including washing cleaning and preparing the walls scaffolding washing of floor and taxes all complete as per building specification and direction of E/I.
61	Providing two coats of plastic emulsion paint of approved shade and make over a coat of cement primer over new surface including preparing plastered surface by rubbing smooth with pumice stone or fine sand paper, applying putty wherever required, scaffolding washing of floor and taxes all complete as per building specification and direction of E/I.
62	Providing two coats of snowcem of approved shade and make over a coat of cement primer on new surface including preparing the plastered surface smooth with sand paper scaffolding , curing and taxes all complete as per building specification and direction of E/I.
63	Providing two coats of painting with ready mixed paint over a coat of primer of approved shade and make over new wooden surface including preparing the surface after cleaning, removing dirt including scales smokes, grease and sand papering including cost of scaffolding and taxes all complete as per building specification and direction of E/I
64	Providing primer one coat of red lead paint of approved make over new steel surface including preparing the surface after cleaning, removing dust, dirt, scales smokes and grease and cleaning the surface throughly including cost of scaffolding and taxes all complete as per building specification and direction of E/I. (Mode of measurement area shall be multiplied by the co-efficient as indicated in building specification)
65	Providing one coat of painting with ready mixed paint of approved shade and make over steel surface including cleaning the surface throughly , scaffolding and taxes all after removing dirt including scales smokes, grease and sand papering including cost of scaffolding and taxes all complete as per building specification and direction of E/I.
66	Providing two coat of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface throughly , scaffolding and taxes all after removing dirt including scales smokes, grease and sand papering including cost of scaffolding and taxes all complete as per building specification and direction of E/I.
67	Providing 250mm. Wide brick drain in cement mortar (1:6) with av. 150mm clear depth and 250mm apron including cost of eartwork involved with 75mm cement concrete (1:4:3) over one brick designation 75A flat soling in proper grade and slope at the base the drain duly plastered in C.M. (1:3) with punning over exposed surface all complete as per building specification and direction of E/I.
68	Supplying, fitting and fixing C.A.R.W.D. Pipe with necessary strips spikes, bends, shoes etc. Including cost of carriage, all complete, as per building specification and direction of E/I. : 75mm dia
69	Water proofing for Old and New Roof Slab :- Providing and laying water proofing treatment on roof slab by applying two Component, factory designed, ready to use, acrylic modified flexible
70	Covering of treated surface with PCC :- Providing 25 mm thick Cement Concrete M20(1:1.5:3) maintaining slope in alternate 2 mt x 2 mt panels with aaproved quality of stone chips of 20 mm
71	Providing and mixing Liquid Intergral water proofing compound in Conctrete or plaster as per manufacturer specification and as per direction of Eng - in Charge.
72	Providing and filling of 6 mm thickGroove between 25 mm PCC Panels with Polysulphide Sealant (Poring Grade)as per drawings and technical specifications and direction of E in Charge.(with 18% GST) ,
73	Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m. All kinds of soil
74	Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:.3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.
75	Providing and fixing factory made P.V.C. door frame of size 50x47 mm with a wall thickness of 5 mm, made out of extruded 5 mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturer's specification and direction of Engineerin-Charge.
76	Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm thick heat moulded PVC 'C' channel of size 30 mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7 mm (5 mm+2 mm) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the 'C' Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge, manufacturer's specification & drawing. 30 mm thick plain PVC door shutters
77	Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer in-charge: Profile B Fixing with adjustable lugs with split end tail to each jamb
78	Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.
79	Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes
80	Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).
81	Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement: 4 coarse sand): 25 mm thick
82	Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete.
83	Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement: 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.
84	Providing corrugated G.S. sheet roofing including vertical/ curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 0.63 mm thick with zinc coating not less than 275 gm/ m2
85	Providing ridges or hips of width 60 cm overall width plain G.S. sheet fixed with polymer coated J or L hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers complete. 0.63 mm thick with zinc coating not less than 275 gm/m2
86	Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. : 110 mm diameter
87	Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.
88	Coupler 75 mm
89	Single tee with door 75x75x75 mm
90	Single tee with door 110x110x110 mm
91	Single tee without door 75x75x75 mm
92	Bend 87.5° 75 mm bend
93	Bend 87.5° 110 mm bend
94	Shoe (Plain) 75 mm Shoe
95	Shoe (Plain) 110 mm Shoe
96	Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-Charge) of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05mm) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.
97	Providing and fixing precoated galvanised steel sheet roofing accessories of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05 mm) with Zinc coating 120 gram per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete :
98	Ridges plain (500 - 600mm)
99	Flashings/ Aprons.( Upto 600 mm)
100	Gutter (600 mm over all girth)
101	Providing and fixing thermal insulation with Resin Bonded rock wool conforming to IS: 8183, having density 48 kg/m3, 50 mm thick,wrapped in 200 G Virgin Polythene Bags fixed to wall with screw, rawel plug & washers and held and in position by criss cossing GI wire etc. complete as per directions of Engineer-in-Charge.
102	Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.
103	Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm)
104	Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.
105	Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50 mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. : 80 mm thick C.C. paver block of M-35 grade with approved colour design and pattern
106	Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps
107	Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : 610x460 mm bowl depth 200 mm
108	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall
109	25 mm nominal dia Pipes
110	32 mm nominal dia Pipes
111	40 mm nominal dia Pipes
112	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings and fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc.
113	15 mm nominal dia Pipes
114	20 mm nominal dia Pipes
115	25 mm nominal dia Pipes
116	Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work 50 mm dia nominal bore
117	Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.
118	Providing and fixing PTMT grating of approved quality and colour. Circular type 100 mm nominal dia
119	Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 150 mm dia. R.C.C. pipe
120	Supplying and fixing C.I. cover without frame for manholes : 500 mm diameter C.I. cover (medium duty) the weight of the cover to be not less than 58 kg
121	Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
122	Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portion :Powder coated aluminium (minimum thickness of powder coating 50 micron)
123	Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): :With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm
124	Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 200 mm nominal size dia
125	Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of useable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by “V” notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, including disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge
126	Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 200 mm dia
127	Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 200 mm clamp
128	Designing, providing, installing and fixing factory finished custom designed cold form Light Gauge Steel Framed super structure comprising of steel wall panel, trusses, purlins etc manufactured out of minimum 0.75 mm thick steel sheet as per design requirements. The steel sheet shall be galvanized (AZ-150gms Aluminium Zinc Alloy coated steel having minimum yield strength 300-550 Mpa) conforming to AISI specifications and IBC 2009 for cold formed steel framing and construction and also as per IS: 875-1987, ISO 800-1984 and IS:801- 1975. The wind load shall be as per provisions of IS 875 (part -III). LGSFS frame shall be designed as per IS: 801 using commercially available software such as Frame CAD Pro-11.7/ STAAD PRO-V8i/ArchitekV2.5.16/ Revit architecture-2011 or equivalent. Proper usage of Connection Accessories like Heavy Duty Tension Ties, Light Duty Hold-ons, Twist Straps (to connect truss with wall frames), Strong Tie, Tie Rod, H-Brackets, Boxing Sections, L-Shaped Angles for better structural stability. The framing section shall be cold form C-type having minimum web depth 89 mm x 39 mm flange x 11 mm lip in required length as per structural design requirement duly punched with dimple/slot at required locations as per approved drawings. The slots will be along centre line of webs and shall be spaced minimum 250 mm away from both ends of the member. The frame can be supplied in panelized or knock down condition in specific dimensions and fastened with screws extending through the steel beyond by minimum of three exposed threads. All self drilling tapping screws for joining the members shallhave a Type II coating in accordance with ASTM B633(13) or equivalent corrosion protection of gauge 10 & 12, TPI 16 & 8 of length 20 mm. The frames shall be fixed to RCC slab or Tie beam over Neoprene rubber using self expanding carbon steel anchor bolt of dia as per approved drawings. design subject to minimum 12 mm diameter and 121 mm length conforming to AISI 304 and 316 at 500 mm c/c with minimum embedment of 100 mm in RCC (RCC to be paid separately) and located not more than 300 mm from corners or termination of bottom tracks complete in all respects. The item also includes the submission of stability reports duly examined and issued by any NIT/IIT. The rate includes the concept design, detailed design, fabrication of sections, transportation, installation and all required fixing arrangement at site as described above.
129	Providing and fixing of external wall system on Light gauge steel frame work with outer face cement boards as per standard sizes fixed with self- drilling / taping screws / fasteners @ 60 cm c/c of approved make. A groove of 2 mm to 3 mm shall be maintained and grooves shall be sealed with silicon based sealant. The board shall be fixed in a staggered pattern. Screws shall be of counter sunk rib head of 1.60 mm to 4 mm thick or 8 to 10 gauge of length varying from 25 to 45 mm and. Internal face 12.5 mm thick gypsum plaster board fixed on cement board as per standard sizes fixed with self- drilling / taping screws / fasteners @ 60cm c/c of approved make, proper taping and jointing to be done using fiber mesh tape and epoxy and acrylic based jointing compound for seamless finish.(cost of frame work to be paid for separately) Outer face: Outer face having 8 mm thick cement bonded particle Board fixed on 10 mm thick cement bonded particle board. (Termite, Fire and Moisture Resistance) as per IS 14276:1995. Inner face:-12.5 mm thick gypsum plaster board conforming to IS 2095:2011 fixed on 8 mm thick cement bonded particle board (Termite, fire and moisture resistance) confirming to IS:14276:1995)
130	Providing and fixing internal wall panels on Light gauge steel frame work with 12.5 mm thick gypsum plaster board conforming IS 2095:2011 fixed on cement board as per standard sizes fixed with self-drilling / taping screws / fasteners @ 60 cm c/c of approved make, Screws shall be of counter sunk rib head of 1.60 mm to 4 mm thick or 8 to 10 gauge of length varying from 25 to 45 mm. Proper taping and jointing to be done using fiber mesh tape and epoxy and acrylic based jointing compound for seamless finish.(cost of frame work to be paid for separatelyCement Bonded particle board 8 mm (Termite, Fire & Moisture Resistance), as per IS:14276 : 1995
131	Supplying and installation of moisture resistant/fire resistant cement board as per standard sizes fixed with self-drilling / taping screws. Screws shall be of counter sunk rib head of 1.60 mm to 4 mm thick or 8 to 10 gauge of length varying from 25 to 45 mm. Cement Bonded particle board 8 mm thick (Termite, Fire & Moisture Resistance), as per IS:14276 : 1995
132	Supplying, fitting and fixing vitreous white glazed earthen ware l.W.C.of parry Hindustan or any other l.S.S.approved make with 100mmH.C.l. 'p'trap lS litres C.l. pull and let go flushing cistern of namesor other l.S.S.equivalent make, complete with allfittings,C.l. or C.C.brackets 32mm alkathene/P.V.C. telescopic flush, pipe about 2 Mlong with one brass coupling and clamps G.l. chain and pull includingsupplying and fixing a pair of vitreous white glazed earthenware warefootrest to be fixed in floor 1Smm C.l. body brass spindle stopecock of weight not less than SOgrms, 15mm P.V.C. connection pipe450 mm. long and the exposed pipe and cistern with two coats ofapproved paint over a coat of red oxide primer etc. all complete asper specification and direction of E/l.(A) 580 mm.long(c) With 10lit. low level PVC cistern
133	Suppling, fitting and fixiilS40mm high-vitreous white glazed earthen E.W.C. with 'p' trap of parry hindustan or any other approved l.S.S. make including supplying and fixing l5litres C.l. mosquito proof low down flushing cistern of approved make with complotefittings with C.l.handle and R.S. or bracket with telescopic flush pipe with brass coupling and plumbers joints spindle stop cock of approved quality weight not less than 450grams 1Smm P.V.C. alkathene pipe 45cm. long with brass coupling at both ends and white/blackplastic solid state seal and lead of commander/cuckoo or other LS.S. make with hinges or screws etc. painting pipe and cistern etc. with 2 coats of approved paint over a coat of red oxide priming, all complete as per specification and dlrection of E/I.(i) With 'P'trap(b) 10 lit. low level PVC clstem
134	Supplying, fitting and fixlng flat back or angular, lipped front vitreous white glazed earthen ware urinal of 'Hindustan 'Parry\\" or any other approved l.S.S make wifi 5 liters capacity C.l. automatic fulsing cistern of reliance for any other l.S.S. approved make with all fittings with C.l.or R.S. brackets, standard size G.l. flush pipe with fitting clamps.15mm C.I. body brass splndle stop cock of approved quality weight not less than 400grams, 15mm P.V.C./Alkthene pipe 450mm long with brass coupling at both ends and doing plumber joints including painting of exposed part with two coats of approved paint over a priming coat of red oxide, cutting wall and floor, making good the same etc. all complete as per specification and direction of E/l.(a) Flat back or standing corner (600mmX350mm)
135	Providing and fixing G.M. non-return valve Horizontal/vertical typeof approved qualilty as per specification and direction of Engineerin-Charge.
136	(A) Horizontal non-return valve :32mm dia weiqht not less than 600qms.
137	(B) Vertical non-return valve: 32mm dia weiqht not less than 600qms.
138	(B) Vertical non-return valve: 40 mm dia
139	(B) Vertical non-return valve: 25 mm dia
140	Cutting chajja or cornice for laying G.l. pipe and restoring the samewith R.C.C.(1:2:4) brick work in cement mortar ('1:4) and cementplaster(1:4) as per specification and direction of Engineer-in-Charge.
141	Making holes in walls for laying G.l. pipes and restoring the sameafter pipe lavinq as per specification and direction of E/\|.
142	125 mm thick wall
143	250 mm thick wall
144	Supplylng, fitting and fixing the following items complete withall materials as per specification and direction of E/I. (b)Mlnors of 6mm thick olate olass bovelled edoe mlnor includingC.P. brass revolving fittings 3mm ply wood board and C.P. hinges tofix with mirror.i) 600mm x 450mm size
145	Earth work in excavation for laying of different types and sizes ofR.C.C. spun pipes with disposal of excavated earth within initial leadand lift as per specification and direction of E/l.(i) For classification of soil item-A
146	Labour for laying, fitting and fixing NP2 R.C.C. spun pipe with collarsin lines, level and grade and providing approved jointing materialsand joints properly filled to make them leak, proof including providingsight rail bonnin rod, night guard, Red light and barrier etc.all complete as per-secification and direction of E/I.150mm dia R.C.C. spun pipeUpto 3.0 metre depth of invert below G.L
147	Supplying materials and labours for constructing inspection chamberof designation class 75B bricks size 750mm deep, 600x450mm internal dimension having 250mm wall thickness in cement mortar (1:6)including 12mm cement plaster (1:4) with punning on inside andcement plaster (1:6) with 600x475mm G.l. Cover with frame (weightnot less than 36k9.) alongwith earth work in excavation and 80 mmthick P.C.C. (1:3:6) in foundation and refilling all complete as per specification and direction of E/\|.
148	Circuit/ submain wiring in PVC conduit :-Wiring for circuit/ submain wiring along with earh wire with the followingsizes of FR PVC insulated copper conductor single core cable in surface /recessed PVC conduit as required
149	2x1.5 sq.urm+ 1x 1.5 sq.mm earth wire
150	2 x2.5 sq.mm + I x2.5 sq.mm earth wire
151	2 x 4.0 sq.mm + 1 x 4.0 sq.mm earth wire
152	2 x 6.0 sq.mm + I x 6.0 sq.mm earth wire
153	2 X 10 sq. mm + 1 X 6 sq. mm earth wire
154	4 x 6.0 sq.mm +2x6.0sq.mm earth wire
155	Point wiring in PVC conduit, with piano type switch :-Wiring for light point/fan point/exhaust fan point/call bell point, with 1.5 sq.mm FR PVC insulated copper conductor single core in surface/recessed PVC conduit, piano type switch,phenolic laminated sheet with suitable size PVC/MS box etc as required
156	Group A
157	Group-C
158	Power plug widng in PVC conduit (2 x 4 sq. run) :-Wiring for light/power plug with 2 x 4 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit, along with 1 No 4 sq.nrm FR PVC insulated copper conductor single core cable for loop earthing etc as required.
159	TV cablc i1efisfing conduit:-Supplying and drawing co-axial TV cable RG-6 grand 0.7 mm solid copperconductor PE insulated ,shielded with fine tinned copper braid and protectedwith PVC sheath in the existing surface / recessed steel / PVC conduit asrequired.
160	Supplying and drawing following sizes of FRLS/HFFR PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. :2 x 1.5 sq. mm
161	S/F PVC conduit :-Supplying and fixing of following sizes of PVC conduit along with accessories in surface / recess including cutting the wall and making good the same in case of recessed conduit as required. : 20 mm
162	S/F PVC/G.I. boxes :-Supplying and fixing of following sizes of PVC/G.I box on surface / recesswith suitable size of phenolic laminated sheet cover in front includingpainting etc. as required.75 mm x 75mm x 50mm deep/ (4\\" x 4\\")
163	S/F Piaoo type switch/ socket :-lSupptyrng and fxing of following piano type switch / socket on the existinglswitch box / cover including connections etc. as requted.
164	5/6 amps, one way switch
165	3 pin 5/6 amps, socket outlet
166	TV antenna socket outlet
167	Electronic step fan regulaior, mini
168	S/F light plug point with piano 6pe acccssories :-lSupplying and fixing suitable size GI/PVC box of 75 qm x 75 mm x 50mm deep on surface or ln reccss wtth suttablo alzo of phcnolic laminatedlshoot covor in front including providing and fixing 3 pin 5/6 amps socketloutlct aod 5/6 amps piauo typc switch, ooniocdon, potottry cto, as rcquircdl(For light plugs to bc uscd in non rrsidmtial buildings )
169	S/F power plug point with piano type accessories :-Supplying and fixing suitable size GI/PVC box of 121 mm x l73mm x48mm/(6\\" x 8\\") (nominal size ) on surface or in recess with suitable size ofphenolic laminated sheet cover in front including providing and fixing 6 pinl5/16 amps socket outlet and l5/16 amps piano tlpe switch. connection,painting etc. as required
170	S/F ceiling rose :-supplying and fxing 2 pin 5 amp. Ceiling rose on the existing junction box/wooen block including connection etc. as required
171	S/F Batten holder :-supplying and fixing Batten / Angle holder including connection etc as required.
172	S/F Dingdong Call bell :Supplyrng and fixing Ding-Dong sound call bell single phase. 230 volt,complete as required
173	ITC fluorescent fitting directly on surface :-Installation testing and commissioning of pre-wired, fluorescent fitting . compact fluorescent fitting of all types, complete with all accessories and tube etc. directly / wall. including connection with 1.5 aq.mm FR PVC insulated . copper conductor single core cable and earthing etc. as required.
174	ITC fluorescent fitting with down rods:-Installation testing and commissioning of pre-wired, fluorescent fitting .compact fluorescent fitting of all types,complete with all accessories and tube etc. including supplyrng and fixing ball and socket arrangement 2 no. down rods of 20mm dia x 1.6 mm thick steel conduit/Gl pipe upto 30 cm length. , painting and wiring the down and connection with 1.5 sq.mm PVC insulated, copper conductor, single core cable and earthing etc. as required
175	ITC ceiling fan:-Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq.mm FR PVC insulated, copper conductor, single core cable etc. as required.
176	ITC Exhaust Fan upto 450 mm sweep: installation of exhaust fan upto 450 mm sweep in the existing opening, including making the hole to cut the size of the above fan, making good the damage, including connection, testing, commissioning etc as required.
177	S/F MCCB in cubical panel board :Providing and fixing following rating and breaking capacity MCCB withthermomagnetic release and terminal spreaders in existing cubicle panelboard including drilling holes in cubicle panel, making connections, etc. asrequired. 25-100 amps, 16 KA, fxed thermal setting
178	S/F S.P. MCB DB :-Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, compiete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) :8 way, Double door
179	S/F T.P. MCB DB :Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bat earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/ RCCB/ Isolator) :4 way(4+12) Double door Horizontal type
180	S/F VERTICAL rr{$f.P. MCB DB :- Supplying and fixing of following ways surface/ recess mounting verticaltype, 415 volts, TPN MCB distribution board of sheet steel, dust protected,duly powder painted, inclusive of 200 amps tinned coPPer bus bar,common neutral link, earth bar, din bar for mounting MCB's (but withoutMCB's and incomer ) as required . (Nobe : Vertical type MCB TPDB isnormally used where 3 phase outleb are required.)4 way (8 + 12), Double door, Vertical tlpe
181	S/F 'C' series SP MCB: Supplying and fixing 6 amps to 32 amps rating, 240 volts, 10 kA, \\"C\\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, esting and commissioning etc. as required.
182	6/32 amps, Single pole
183	40 amps, DP
184	50/63 amps, DP
185	40 amps, TPN
186	Earthing with G.I. earth pipe 4.5 mtr long . 40mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal and salt as required.
187	Earthing with copper earth plate 600mm x 600mm x 3mm thick includingaccessories, and providing masonry enclosure with cover plate havinglocking arrangement and watering pipe etc. (but without charcoal or cokeand salt) as required
188	Earthing with copper earth plate 600mrn x 600mm x 3mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. (with charcoal or coke and salt)as Required.
189	Supplying and laying 8 SWG copper wire at 0.50 Metere below ground level for conductor earth electrode, including soldering etc. as required.
190	S/L 25mm x 6mm G.I. earth strip in ground :Providing and laying earth connection from earth electrode with 6 SWG diaG.L Wire in l5mm dia G.I. pipe from earth electrode, as required
191	Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing etc.as required.
192	P/F G.I. lightning condutor finial :-Providing and fixing of lighting conductor finial , made of 25mm dia 300mm long , G.I. tube, having single prong at top, with 85mm dia 6mm thick G.I. base plate including holes etc. complete as required.
193	P/F G.I. lightning conductor tape in horizontal run :-Providing and fixing G.I. tape 20mm x 3mm thick on parapet or surface of wall for lightning conductor complete as required.( for Horizontal run ).
194	P/F G.I. lightning conductor tape in vertical run :-Providing and fxing G.I. tape 20mm x 3mm thick on parapet or surface of wall for lightning conductor complete as required.( for Vertical run ).
195	Laying of one number PVC insulated and PVC sheathed/ XLPE power cableof l.l KV grade of size exceeding 35 sq mm but not exceeding 95 sq mmdirect in ground including excavation, sand cushioning, protective coveri-ngand refilling the trench etc as required.
196	Laying of one number additional PVC insulated and PVC sheathed/ XLPE power cable of 1.1 KV grade of size exceeding 35 sq mm but not exceeding 95 sq. mm direct in ground in the same trench in one tier horizontal formation including excavation, sand cushioning, protective covering and refilling the trench etc as required.
197	Laying of one number additional PVC insulated and PVC sheathed/ XLPEpower cable of 1.1 KV grade of size exceeding 185 sq mm but notexceeding 400 sq. mm in the existing RCC/HUME/STONEWAREA4ETALpipe as required.
198	Laying of one number PVC insulated and PVC sheathed/ XLPE power cable of 1.1 KV grade of size not excecding 35 sq mm directr in ground including excavation and refilling the trench etc as rquired, but excluding sand Cushioningand prolective covering.
199	S.I.T.C of floowing rating LED Street lighting luminarie with pressure die cast housing and toughened glass cover (IP 66 protection) in existing pole/pipe for supply voltage 100-270V AC,50Hz. Luninarie shall be confirm to IS: 10322 part 5/section-3 and shall be complete with all neccssary accessories as required : 70/72W LED Street light
200	S.I.T.C of floowing rating LED Flood lighting luminarie with pressure die cast housing and toughened glass cover (IP 66 protection) in existing pole/pipe for supply voltage 1C[.Z70Y AC,50Hz. Luminarie shall be confirm tolS:,1,0322part-5/section-5 and shall be complete with all neccssary accessories as required : 90/100W LED Flood light
201	S.I.T.C of floowing rating reccess/surface mounted LED round/square shape Down light luminarie with pressure die cast housing for single phase supply voltage. Luminarie shall be confirm to IS:10322 part-5/section-2 or IEC:62722 with all neccssary accessories as required :18/20W LED Round Down ligh
202	Supply Installation, testing and commissioning of follwing size ceiling fan 3 Blades confirming to13:374,.2019 including wiring the down rods of standard length (upto 30cm) with 1.5sq.mm. FR PVC insulated, copper wire suitable for 230V 50H2, single phase supply etc. complete as required
203	1400mm (56\\") Ceiling Fan
204	1400mm (56\\") BLDC 5star rating 32W Ceiling Fan
205	S.I.T.C of floowing rating surface mounted LED tube light fitting suitable for 230V 50H2, single phase supply etc. complete as required.-20/22W LED Tube light
206	Laying of one number PVC insulated and PVC sheathed/ XLPE power cableof l.l KV grade of size exceeding 185 sq mm but not exceeding 400 sq mmdirect in ground including excavation, sand cushioning, protective coveringand refilling the trench etc as required
207	Erection of C.C. pole upto l1 m in B.B. :Erection of RCC/ PCC pole of following length in brick ballast and rammingthe foundation, finishing with l50mm thick cement concrete (l:3:6) layer ontop with including excavation and refilling etc as required. Above 6.5 metre and upto 8.0 metre
208	Supplyind and making end termination with brass compression gland and Aluminium lugs for flowing size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required
209	3.5x35 Sq mm (32mm)
210	3.5x50 sq.mm (35mm)
211	3.5x240 sq.mm (62 mm)
212	4x10 sq.mm (25 mm)
213	Supplying and making outdoor cable end jointing with cast resin compound, including lugs and other jointing materials, for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required : 70 sq. mm
214	Excavation in Soil using Hydraulic Excavator and Tippers with Disposal upto 1000 metres.Excavation for road work in soil with hydraulic excavator including cutting and loading in tippers, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross sections, and tranporting to the embankment location within all lifts and lead upto 1000 m
215	Excavation in Ordinary Rock using Hydraulic Excavator and Tippers with Disposal upto 1000 metresExcavation for roadwork in Ordinary Rock with hydraulic excavator including cutting and loading in tippers, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross sections, and transporting to the embankment location within all lifts and lead upto 1000m
216	Carrying out excavation in hard rock to achieve a specified slope of the rock face by controlled use of explosives and blasting accessories in property alighed and spaced drill holes , collection of the excavated rock by a dozer, loading in tipper by a front end loader and disposing of the material with all lifts and lead upto 1000 m, all as specified in clasue No. 303.Hard Rock ( Blasting Priohibited)
217	Cast in Situ Cement Concrete M 20 Kerb with Channel (Construction of cement concrete kerb with channel with top and bottom width 115 and 165 mm respectively, 250 mm high in M 20 grade PCC on M15 grade foundation 150 mm thick, kerb channel 300 mm wide, 50 mm thick in PCCM20 grade, sloped towards the kerb, kerb stone with channel laid with kerb laying machine, foundation concrete laid manually, all complete as per clause 409)PCC M20 for Kerb Cast in situ
218	Jungle clearance in borrow area, building premises, flanks and slope on the road, canals and embankment by removing the grass and jungle bushes from the top including weeding out shrubs small trees upto 150 mm dia. and their removal all complete job as per direction of E/I.
219	Trenching in ordinary soil up to a depth of 60 cm including removal andstacking of serviceable materials and then disposing of surplus soil, byspreading and neatly levelling within a lead of 50 m and making up thetrenched area to proper levels by filling with earth or earth mixed withsludge or / and manure before and after flooding trench with water(excluding cost of imported earth, sludge or manure).
220	Supplying and stacking of good earth at site including royalty and carriageupto 5 km lead complete (earth measured in stacks will be reduced by20% for payment)
221	Supplying and stacking at site dump manure from approved source,including carriage upto 5 km lead complete (manure measured in stackswill be reduced by 8% for payment) : Screened through sieve of I.S. designation 20 mm
222	Rough dressing the trenched ground including breaking clods
223	Uprooting weeds from the trenched area after 10 to 15 days of its floodingwith water including disposal of uprooted vegetation
224	Fine dressing of the ground.
225	Spreading of sludge, dump manure and/or good earth in requiredthickness as per direction of officer-in-charge (cost of sludge, dumpmanure and/ or good earth to be paid separately)
226	Mixing earth and sludge or manure in the required proportion specifiedor directed by the Officer-in-charge
227	Digging holes in ordinary soil and refilling the same with the excavatedearth mixed with manure or sludge in the ratio of 2:1 by volume (2 partsof stacked volume of earth after reduction by 20% : 1 part of stackedvolume of manure after reduction by 8%) flooding with water, dressingincluding removal of rubbish and surplus earth, if any, with all leads andlifts (cost of manure, sludge or extra good earth if needed to be paid forseparately) Holes 90 cm dia, and 90 cm deep
228	Providing and laying Neelgiri/Mexican grass turf with earth 50mm to60mm thickness of existing ground prepared with proper level andramming with required tools wooden (Dhurmos) and than rolling thesurface with light roller make the surface smoothen and light, wateringwith sprinkler and maintenance for 30 days or more till the grass establishproperly as per direction of officer-in-charge.
229	Providing & laying of Selection no. 1 Doob grass turf with earth 50mm to60mm thickness of existing ground prepared with proper level andramming with required tools wooden and than rolling the surface withlight roller make the surface smoothen and light watering the same andmaintenance for 30 days or more till the grass establish properly, asper direction of the officer-in-charge.
230	Complete maintenance of the entire garden features having as per yardstick in the garden area i.e. lawn trees, shrubs,herbs, edge, flower beds,foliages & creepers etc. including hoeing, weeding, pruning, replacementof plants, gap filling, watering, mowing of lawn, grass cutting by lawnmover and brush cutter, removal of garden waste, applying insecticide,pesticide & fertilizers (whenever required), top dressing of lawn withgood earth and manure and maintenance of other garden related worksas directed by officer-in-charge (Cost of Good Earth, Manure, Fertilizer,Insecticide, Pesticide, lawn mover and brush cutter with fuel & other T& P material/plants shall be provided by the department.)Residential Flats and Govt. Officers Bungalow. (1.25 Acres= One Mali) As per yard stick.
231	Anti termite treatment by digging holes 300mm deep and 40 mm dia, 6to 7 holes around the tree using chemical emulsion at the rate of 1.5liter per hole in two time or more application to get the trees free fromtermite infection chemicals used Chlorpyriphos 20% EC in the ratio of1% concentration and as per direction of officer-in-charge.
232	Anti termite treatment of lawn area through Chloropyriphose 20% E.C.,5 liter diluted in 995 liters water and applying solution @ 1.00 litre solutionper sqm each application in lawn / bed area (two application) i/c cost ofchemical) and as per direction of officer-in-charge.
233	Providing, stacking and Displaying Bamboo Buddha Valley with fresh &healthy 5 to 6 suckers 1.80 m to 2.10m ht umbrella type plant welldeveloped in 50 cm Cement Pot/ Plastic Pot and as per direction of theofficer-in- charge.
234	Providing, stacking and Displaying Bismarckia Palm 115 cm to 180 cmht. plant, well developed 12 and above good color fresh and healthyleaves in 40 cm Cement Pot/ Plastic Pot and as per direction of theofficer-in- charge
235	Providing, stacking and Displaying Cycus cirsnallis well developed withfresh & healthy 35 to 40 lush green leaves in 40 cm Cement Pot/ PlasticPot and as per direction of the officer-in-charge.
236	Providing, stacking and Displaying Cycus revoluta in 35 cm challi,specimen plant, having 30 to 40 with fresh and healthy, leaves having25 cm to 30 cm circumfrance of base stem well developed and as perdirection of the officer-in-charge.
237	Providing, stacking and Displaying Ficus Long Island Topiary welldeveloped with fresh & healthy 5 to 6 big ball specific size and shape120 cm to 150 cm ht in 40 cm Cement Pot/ Plastic Pot and as perdirection of the officer-in-charge.
238	Providing, stacking and Displaying Ficus Retusa Topiary well developedwith fresh & healthy 5 to 6 big ball specific size and shape 180 cm to210 cm ht in 40 cm Cement Pot/ Plastic Pot and as per direction of theofficer-in-charge.
239	Providing, stacking and Displaying Phoenix roebelenii palm well developedhaving 20 to 25 fresh & healthy leaves 90 cm to 105 cm ht. plant in 30cm Cement Pot/ Plastic Pot and as per direction of the officer-in-charge.
240	Providing, stacking and Displaying Foxtail palm well developed withfresh & healthy foliage of ht. plant 210 cm to 240 cm in 40 cm CementPot/ Plastic Pot and as per direction of the officer-in-charge.
241	Providing, stacking and Displaying Topiary plant of Ficus Nuda welldeveloped with fresh & healthy foliage from Top to Bottom with singlepiller 75 cm to 90 cm spread, 195 cm to 210 cm ht. plant in 35 cmCement Tray /Cement Pot/ Plastic Pot and as per direction of theofficer-in-charge
242	Providing, stacking and Displaying Topiary plant of Ficus Panda welldeveloped with fresh & healthy foliage with 3 to 4 Ball and 60 cm to 75cm spread each Ball, 135 cm to 150 cm ht. plant, in 35 cm CementTray /Cement Pot/ Plastic Pot and as per direction of the officer-incharge.
243	Providing, stacking and Displaying Travellers palm well developed withfresh & healthy foliage 210 cm to 240 cm ht specimen plant in 40 cmCement Pot/ Plastic Pot and as per direction of the officer-in-charge.
244	Providing and stacking Alternanthera species of height 15 cm to 20 cm,full of branches and foliage in 15 cm size of Earthen Pot / Plastic Potand as per direction of the officer-in-charge.
245	Providing and stacking Duranta Golden, having ht. 15 cm to 20 cmbushy shape with fresh and healthy leaves in 15 cm size of Earthen Pot/ Plastic Pot and as per direction of the officer-in-charge
246	Providing and stacking Iresine herbstii, of height 20 cm to 25 cm. full ofbranches well developed in 15 cm size of Earthen Pot / Plastic Pot andas per direction of the officer-in-charge.
247	Providing and stacking Ophiopogon jaburan ( variegated ), full of variegatedleaves in 20 cm Earthen Pot/Plastic Pot and as per direction of theofficer-in-charge..
248	Providing and stacking Tradescantia, full of leaves in Earthen Pot/PlasticPot of size 15 cm and as per direction of the officer-in-charge.
249	Providing and stacking Tradescantia zebrina having in 15 cm size ofEarthen Pot / Plastic Pot and as per direction of the officer-in-charge.
250	Providing and stacking Wadelia trilobata,full of leaves in 15 cm size ofEarthen Pot / Plastic Pot and as per direction of the officer-in-charge.
251	Providing and stacking of Ficus benjamina (green) height 150-165 cm.,bushy with healthy branches and lush green foliage in big size HDPEbag as per direction of the officer-in-charge.
252	Providing and stacking of Ficus blackii (F.vivion) (bushy) of height 150165 cm. with 8-10 branches and healthy foliage in earthen pot of size30 cm as per direction of the officer-in-charge.
253	Providing, stacking and Displaying Ficus Starlight with fresh, healthyand attractive foliage 45 cm to 60 cm spread 75 to 90 cm ht. plant,specimen bushy plant,in 35 cm Cement Pot/ Plastic Pot and as perdirection of the officer-in-charge.
254	Providing and stacking of Gardenia jasminoides of height 45-60 cm.with 3-4 branches in earthen pot of size 20 cm as per direction of theofficer-in-charge
255	Providing and stacking of Hamelia patens of height 60-75 cm. with 6-8branches in poly bag of size 25 cm as per direction of the officer-incharge.
256	Providing and stacking of Bougainvillea (Variety Butiana, Lady MaryBaring, Mahara,Mohan,Scarlet Queen, Variegated, Glabra Formosa,Peruvian Odissi, Paratha, Subhra,Thimma, Spectabilis L.N Birla,Refulgence) plant of height 30 cm. to 45 cm. with 2-3 branches in 20cm size of Earthen pot / Plastic pot as per direction of the officer-incharge
257	Providing and stacking of Clerodendrum splendens of height 30 cm to45 cm. in 20 cm size of Earthen pot / Plastic pot as per direction of theofficer-in-charge.
258	Providing and stacking of Ipomoea purpurea (Morning glory) of height30 cm to 45 cm. in 20 cm size of Earthen pot/ Plastic pot as perdirection of the officer-in-charge.
259	Providing and stacking of Jasmine humile (Yellow) of height 30 cm to 45cm. in 20 cm size of Earthen pot / Plastic pot as per direction of theofficer-in-charge.
260	Providing and stacking of Quisqualis indicia of height 30 cm to 45 cm. in20 cm size of Earthen pot / Plastic pot as per direction of the officer-incharge
261	Providing and stacking of Tecoma grandiflora of height 30 cm to 45 cm.in 20 cm size of Earthen pot / Plastic pot as per direction of the officerin-charge.
262	Providing and stacking of Vernonia elaegnifolia (curtain creeper) ofheight 30 cm to 45 cm. in 20 cm size of Earthen pot / Plastic pot as perdirection of the officer-in-charge.
263	Supply, installation, testing and commissioning of following capacity (continuous loading) BEE 3 Star rated (Corresponding Level as per BIS amended upto date of receipt of tender) , 11/0.433 KV step down, 3 Phase, 50 Hz, Dyn 11 vector group, ONAN (Oil Natural Air Natural) copper wound transformer (Electrolytic grade 99.9% pure copper, Core made of first grade Cold Rolled Grain Oriented (CRGO) Core grade MOH or better, suitable for out door/indoor applications with On Load Tap Changer (OLTC) on HV side having AVR relay and Remote Tap Changer Control (RTCC) for automatic sensing of incoming voltage, automatic operation of OLTC and facility for remote and manual operation of OLTC HV side in range of +5% to -15% in steps of 2.5%, having cable end boxes on HV side suitable for 3x300 sqmm XLPE cable of 11 KV grade, including bus trunking arrangement on LV side including supplying and laying of copper conductor multicore control cable from transformer to HT breaker/panel for safety tripping, complete with all accessories and safety provisions as per relevant IS Code including first filling of filtered dehydrated oil, i/c supplying and grouting of suitable M.S. Channel with all accessories and transformer shall be confirming to IS : 2026 (Part 1 to Part 5), IS : 1180 and duly ISI Marked and as per CPWD specifications complete in all respects etc as required at site. The maximum flux density in any part of the core and yoke at rated voltage and frequency shall be such that the flux density with + 12.5 percent does not exceed 1.9 Tesla. The permissible temperature-rise shall not exceed 35 dg.C for oil and 40 dg. C up to 200 KVA and 40 dg.C for oil and 45 dg. C for above 200 KVA for winding. Inside of tank shall be painted with varnish or liquid resistant paint. For external surfaces one coat of thermo setting powder paint or one coat of epoxy primer followed by two coats of polyurethane base paint shallbe used. IS: 1180 (Part 3) shall be referred to for paint thickness for normal to medium corrosive atmosphere. For highly polluted atmosphere and special application external paint work shall be as per direction of Engineer-in-Charge. Design ambient condition : a) air temperature 50 deg C, b) Relative Humidity 90 % Max, c) Seismic Zone as per location of site, d) Altitude as per location/site. Noise level Shall not exceed limits as per NEMA TR-1 with all accessories running measured as per IEC 551 / NEMA standard. The transformer should have QR code which should contain drawing, test report OEM manual,Geo- Tag of manufacturing location etc. Marking Each transformer shall be provided with rating plate made of anodized aluminum/ stainless steel material securely fixed on the outer body, easily accessible,as per IS: 1180 Part-3. The entries on the rating plate shall be indelibly marked. Fitting and Accessories : The following fittings shall be provided:- a) Two earthing terminals with the earthing symbol b) Oil level gauge indicating oil level at minimum, 30°C and maximum operating temperature; c) Air release device (for non-sealed type transformers) d) Rating and terminal marking plates; e) Silica gel breather f) Drain-cum-sampling valve (¾″ nominal size thread, IS 554) preferably steel with plug for three phase transformers; g) Thermometer pocket with cap; h) Oil filling holes having (1¼″ nominal size thread) with cover (for sealed type transformers without conservator); i) Lifting lugs for the complete transformer as well as for core and winding assembly; j) Pressure relief device or explosion vent above 200 kVA; k) One filter valve on the upper side of the tank (for transformers above 200 kVA); l) Unidirectional flat rollers (for transformers above 200 kVA); m) Inspection hole (for transformers above 200 kVA); n) HV side neutral grounding strip (where one of the HV bushing terminal is connected to earth); o) Buchholz relay for transformers above 800 kVA. p) Arcing horns or Supply, installation, testing and commissioning of following capacity (continuous loading) BEE 3 Star rated (Corresponding Level as per BIS amended upto date of receipt of tender) , 11/0.433 KV step down, 3 Phase, 50 Hz, Dyn 11 vector group, ONAN (Oil Natural Air Natural) copper wound transformer (Electrolytic grade 99.9% pure copper, Core made of first grade Cold Rolled Grain Oriented (CRGO) Core grade MOH or better, suitable for out door/indoor applications with On Load Tap Changer (OLTC) on HV side having AVR relay and Remote Tap Changer Control (RTCC) for automatic sensing of incoming voltage, automatic operation of OLTC and facility for remote and manual operation of OLTC HV side in range of +5% to -15% in steps of 2.5%, having cable end boxes on HV side suitable for 3x300 sqmm XLPE cable of 11 KV grade, including bus trunking arrangement on LV side including supplying and laying of copper conductor multicore control cable from transformer to HT breaker/panel for safety tripping, complete with all accessories and safety provisions as per relevant IS Code including first filling of filtered dehydrated oil, i/c supplying and grouting of suitable M.S. Channel with all accessories and transformer shall be confirming to IS : 2026 (Part 1 to Part 5), IS : 1180 and duly ISI Marked and as per CPWD specifications complete in all respects etc as required at site. The maximum flux density in any part of the core and yoke at rated voltage and frequency shall be such that the flux density with + 12.5 percent combined voltage and frequency variation from rated voltage and frequency does not exceed 1.9 Tesla. The permissible temperature-rise shall not exceed 35 dg.C for oil and 40 dg. C up to 200 KVA and 40 dg.C for oil and 45 dg. C for above 200 KVA for winding. Inside of tank shall be painted with varnish or liquid resistant paint. For external surfaces one coat of thermo setting powder paint or one coat of epoxy primer followed by two coats of polyurethane base paint shallbe used. IS: 1180 (Part 3) shall be referred to for paint thickness for normal to medium corrosive atmosphere. For highly polluted atmosphere and special application external paint work shall be as per direction of Engineer-in-Charge. Design ambient condition : a) air temperature 50 deg C, b) Relative Humidity 90 % Max, c) Seismic Zone as per location of site, d) Altitude as per location/site. Noise level Shall not exceed limits as per NEMA TR-1 with all accessories running measured as per IEC 551 / NEMA standard. The transformer should have QR code which should contain drawing, test report OEM manual,Geo- Tag of manufacturing location etc. Marking Each transformer shall be provided with rating plate made of anodized aluminum/ stainless steel material securely fixed on the outer body, easily accessible,as per IS: 1180 Part-3. The entries on the rating plate shall be indelibly marked. Fitting and Accessories : The following fittings shall be provided:- a) Two earthing terminals with the earthing symbol b) Oil level gauge indicating oil level at minimum, 30°C and maximum operating temperature; c) Air release device (for non-sealed type transformers) d) Rating and terminal marking plates; e) Silica gel breather f) Drain-cum-sampling valve (¾″ nominal size thread, IS 554) preferably steel with plug for three phase transformers; g) Thermometer pocket with cap; h) Oil filling holes having (1¼″ nominal size thread) with cover (for sealed type transformers without conservator); i) Lifting lugs for the complete transformer as well as for core and winding assembly; j) Pressure relief device or explosion vent above 200 kVA; k) One filter valve on the upper side of the tank (for transformers above 200 kVA); l) Unidirectional flat rollers (for transformers above 200 kVA); m) Inspection hole (for transformers above 200 kVA); n) HV side neutral grounding strip (where one of the HV bushing terminal is connected to earth); o) Buchholz relay for transformers above 800 kVA. p) Arcing horns or suitable rating lightning arrestors for HT side – 3 Nos. q) Bird guard; r) Oil temperature indicator and winding temperature indicators for transformers above 200 kVA with suitable tripping mechanism above permissible limit s) Jacking pads (for transformer above 1 600 kVA); t) Additional Neutral separately brought out on bushing for earthing. u) Magnetic oil level gauge (for transformer above 1600 kVA) with low oil level alarm contact; v) Non return valve (for conducting pressure test); w) Pressure relief device or explosion vent x). Monogram Plate y) Inspection cover z). Detachable type radiators with top and bottom shutoff valve. aa) Oil Conservator with Oil level indicator, minimum level marking and drain plug for all transformers of capacity 50 KVA and above. bb) Necessary hardware, clamps, lugs etc. for termination on HV/MV etc. for all transformers.200KVA
264	HT Cable Laying 3Cx70 sq mm: Laying of one number 3CX120 sq mm PVC insulated and PVC Sheathed / XLPE power cable of 11 kV grade of following size direct in ground including excavation and refilling the trench etc as required but excluding sand cushioning and protective covering.
265	Supplying of PVC/XLPE insulated PVC sheathedheavy duty, armoured electrical cable with aluminiumconductor forworking voltage up to and including 1100 volts. (Conforms to IS:1554,part-1):25 sq. mm,3.5 core
266	Supply & laying of following PVC/XLPE insulated PVC sheathedheavy duty, armoured electrical cable with aluminiumconductor forworking voltage up to andincluding L100 volts. ( Confirm to IS: 1554, part-1). 35 sq. mm,3.5 core
267	Supply & laying of following PVC/XLPE insulated PVC sheathedheavy duty, armoured electrical cable with aluminiumconductor forworking voltage up to andincluding L100 volts. ( Confirm to IS: 1554, part-1). 50 sq. mm,3.5 core
268	Supply & laying of following PVC/XLPE insulated PVC sheathedheavy duty, armoured electrical cable with aluminiumconductor forworking voltage up to andincluding L100 volts. ( Confirm to IS: 1554, part-1). 240 sq. mm,3.5 core
269	PVC/XLPE insulated PVC sheathedheavy duty, armoured electrical cable with aluminiumconductor forworking voltage up to andincluding L100 volts. (Conformsto IS:1554,part-1)16 sq. mm,2 core
270	Supply & laying of following PVC/XLPE insulated PVC sheathedheavy duty, armoured electrical cable with aluminiumconductor forworking voltage up to andincluding L100 volts. ( Confirm to IS: 1554, part-1). 10 sq. mm,4 core
271	OCTAGONAL POLE 7 Mtr. height Octagonal Hot - Dip galvanized pole( BOP - 7030) withtop dia 70 mm, bottom dia L30 mm & made of 3 mm thick sheet, base plate dimensions200X 200X12mm ( Lx B xT) including suitable sizes of foundation bolt all complete as reqd. (Without Arm)
272	OCTAGONAL POLE 9 Mtr. height Octagonal Hot - Dip galvanized pole( BOP - 9031) withtop dia 70 mm, bottom dia 130 mm & made of 3 mm thick shee! baseplate dimensions 200X200X1.6 mm ( Lx BxT) including suitablesizes of foundation bolt all complete as reqd. (Without Arm)
273	0.5m Single Arm suitbale for 70mm Top
274	0.5m double arm suitable for 70mm Top
275	9\\" (230mm) metal exaust fan
276	15' (380mm) metal exaust fan.
277	9/1OWatt LED Bulb
278	15/16Watt LED Bulb
279	Supply of 12mtr. High mast in one section Construction 5355 grade as per BIEN 10 025 Top Dia 100mm, bottom dia 360mm, plate thickness 3mm, 12side polygon, galvanisation as per BS EN ISO 1461, base plate dia 520mm, base plate thickness 25mm, GI single spike Ughting protection, maximum wind speed 47m/ s as per IS : 875 (Part-III) with 6 nos foundation bols of PCD r145mm TS 600/ 24mm dia/850 mm long. Luminaries carriage : Material for 40 NB ERW Class B - M.S. Pipe, dia of carriage ring 450mm (ID) with 8 arm, welded,2 sections having carrying capacity upto S luminaries. Trailing Cable : 5 core 2.5sq.mm. PVC flexible copper conductor Winch/Power Tool : Double drum, SWL 350 Itg with 0.75HP 6 pole single speed integral motor Rope : Grade AISI 1304,7 /19 construction, dia 5mm, BLC 1450 x 2 having 2 nos of continues lrope. Aviation obstruction light: twin dome aviation obstruction lights It CO typu as required. (But excluding Feeder Pillar)
280	Silent type D.G Set of capacity 20 KVA Three Phase With AMF PanelISlIEC-60034-1 IS: 1460 IS: 13018
281	Special type of C.P. Bath room fittings for V.l.P. Buildings(JAL, Jaquar, Marc or equivalent make) (lSl Marked)Wall mixer with provision for over head shower with elbowcoupling and wall flange (lSl Marked)
282	Cost of Driling 200mm x 165mm x 125 mtr.deep bore well in all kind of Soil and rock in rural area for instalation of pump set with Hydrolic DTH Rig machine all complete including all materials, tools,driling rig,air compressureand equipmentsas well as fule, lubricantsand cost of transportation of rig machine annd other vehical up to Site.
283	From 0-50 meter
284	From 51-125 meter
285	Special type of C.P. Bath room fitting for VIP Building (JAL,Jaquar,Marc or equivalent make) (ISI Marked)
286	bib cock long thread ISI MARKED
287	Pillar cock (long neck) ISI MARKED
288	Angular Stop Cock (long Thread) ISI MARKED
289	TOILET Paper holder V.I.P.
290	Glass self 22\\"
291	TOWEL RING
292	soap dish
293	Chlorinated Polyvinyl - chloride (CPVC) pipe 100 mm nominal dia
294	Supplying submersible pump sets confirming to IS 8034 and motor confirming to IS 9283. Pump shall be suitable for various delivery head and discharge with stainless steel pump shaft and polypropylene/noryl impeller. Motor suitable for working on 415V + 10%, 3PH, 50 Hz, A.C. supply with cable guard, thurst carbon/fiber bearing to withstand entire hydraulic thurst, water proof winding shall be provided. The pump set shall be suitable for direct coupling. Pump shall have suitable outlet as Meteranufacturers design. Anti thurst stream lined non return valve shall be provided with pump, 3 Meter submersible copper conductor cable in single/double run shall be provided with Each pump.Submersible pump set 100mm dia (with Polypropylene/Noryl Impeller) up to 20 stages1.5 HP
295	Supplying Full automatic star selta starter to operate induction motor working on 415v 3phase 50hz with no coil. Over load element , On _OFF push buttom with necessary materials and connection to Supply etc complete starter with original sheel steel encloser as per 3914.F.A.S.D starter 10.0 H.P.
296	Bus bar 200A- 1 setOutgoingsMCB, 4P, 63A, for PDBs -1 noMCB, 4P, 40A, for LDBs -7 nos10 kW , 3 phase meter Analogue type voltmeter (0-500V) of 96 sq.mm. With selector switches.Analogue type Ammetesr (0-100A) of 96 sq.mm. With selector switch. .CT 100/5VA -5 class one Epoxy resin cast CT 1 Set of 3. Bakalite Fuse base with HRC Fuse 20A. 1 Set of 3. LED indicatore (RYB) of 220V. 1 Set. Interconnection wires 2.5 Sq mm and 4 Sq mm etc.Sub-Total of non - schedule items - (B)
297	Outdoor Feeder Panel ( for street light): Supplying, designing, manufacturing, installation, testing and commissioning in correct alignment position, effecting proper connection of all incomer and outgoing of outdoor type cubical feeder pillar of suitable size not less than 30 cm and up-to 45 cm deep made out of M.S. sheet 2 mm thick (14 SWG) duly compartmentalized, double door with locking arrangement (IP-54), duly fixed on MS angle iron frame work of suitable size ,earthing with two nos. earth studs, powder coated with rain shed structure etc as reqd. All inter connections shall be made with 2.5, 4 , 6 Sq mm PVC Cu. wire. The sheet steel under go minimum 7 tanks treatment followed by finishing of powder coating of minimum 60 micron thickness, duly compartmentalized having accessories mounted inside the cubical panel, earthing with 2 Nos. earth studs Incomer : 1 No. 63A/FP/10kA/ MCB . 0-24hrs Timer switch with bypass arrangement, 40A duty contactorOutgoings: MCB 40 A, TPN, 10kA-1 no for highmast and MCB 20 A, TPN, 10kA - 6 nos for street light and bollards100 amp 415 V heavy duty three phase with neutral busbar chamber
298	Main LT Panel :- Supplying, designing, manufacturing, installation, testing and commissioning of LT Panel of 14 SWG CRCA sheet (2 mm) steel , dust and vermin proof with reinforcement of suitable size iron channel , with proper lifting arrangement effecting proper connection of all incomers and outgoing(IP-43) fully compartmentalized cubical type, floor mounted , totally enclosed, extendable on both sides, switch board and suitable for operation on 415V, 50Hz, 3 Ph. AC supply and fault level 50 kA with front operated construction including separate fabrication arrangement for fixing MCCBs and Bus Coupler. The sheet steel under go minimum 7 tanks treatment followed by finishing powder coating of minimum 60 micron thickness duly compartmentalized having accessories mounted inside the cubical panel, earthing with 2 Nos. earth studs. SetThe panel includes 415V, 400A, 3Ph, 50kA, 50Hz Electrolytic Aluminium Bus Bar (E91EWP) Aluminium, Earth Bus for main supply, removable glands plates, cable glands and sending and receiving ends, including connection with outgoing Feeders complete in all respects. All inter connections shall be made with 2.5 ,4, 6, 10 Sq mm PVC Cu. wire. All incomer MCCB and bus coupler shall be mechanically operated . All 4 pole MCCB with thermomagnetic based release must have following character: Icu=100% Ics with adjustable S/C and O/L Make : ISG Ranchi/ SPC Electrotech/ Application Control Panel Pvt Ltd/ Electric Point MCCB/MCB: HPL/Havells/Legrand/Anchor/C&S/Indo Asian/ABB/Hager Provision for inbuilt earth leakage module & provision for inbuilt measuring unit. The panel consisting of the followings 1 No, 315A/FP/36kA/ MCCB thermomagnetic release type, and S/C, O/L protection, with Rotary Handle & Spreader links. ( for incomer for JSEB suppy) 1 No 100A/FP/16kA/ MCCB thermomagnetic release type, and S/C, O/L protection, with Rotary Handle & Spreader links. ( incomer for DG suppy) Electro-mechnical lock for auto changeover -1 set: 100A, 4P Current transformer 400/5A, 15VA, class 0.5 -3 each -1 set 3 phase kWh meter-1 no LED indicators for each phase and ON/OFF/TRIP -2 set Busbar- 415V, 400 A, 36 kA, 3ph, 4wire AL BUSBAR-1 , extensible Outgoings: MCB TPN 63A, 10 kA- 6 nos MCB TPN 40A, 10kA- 2 nos
299	Providing 16 mm dia L Drop 300 mm long Iron(copperoxidized)with screw and all fittings with C.P+OHC.(M-219(i))
300	Construction of Embankment with Material obtained from Borrow pits. Construction of Embankment with approved material obtained from Borrow pits with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacting to meet requirement of Table 300-2.
301	\\"Construction of Subgrade and Earthen Shoulders\\"Construction of sub-grade and earthen shoulders with approved material obtained from Borrow pits with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacting to meet requirement of Table 300-2.
302	Cement Treated Crushed stone Sub base Plant Mix MethodConstruction of granular sub-base by providing graded Material, mixing with cement in a mechanical mix plant at OMC, carriage of mixed Material to work site, spreading in uniform layers with mechanical paver on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per clause 401.(i) Rate per cum for Grading -III Material
303	Wet Mix Macadam (Plant Mix Method)Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with grader in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density.
304	Prime Coat over WMM/WBMProviding and applying primer coat with SS1 grade bitumen emulsion on prepared surface of granular Base including clearing of road surface and spraying primer at the rate of 0.70 kg/sqm using mechanical means.
305	Tack Coat on Bituminous surfacesProviding and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.20 kg per sqm on the prepared bituminous surface cleaned with mechanical broom.
306	Tack Coat on Granular surfaces treated with primerProviding and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.25 kg per sqm on the prepared bituminous surface cleaned with mechanical broom.
307	Dense Graded Bituminous Macadam Grading -I with VG-40 Bulk Bitumen Providing and Laying dence graded bituminous macdam with higher capacity batch type HMP using crushed aggregates of specified grading, premixed with bituminous binder @ 4.0 per cent by weight of total mix and filler , transporting the hot mix to work site , laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment , rolling with smooth wheeled , vibratory and tandem rollers to achieve the desired compaction as per MoRTH specification clause no. 505 complete in all respests with VG-40 Bulk Bitumen.
308	Dense Graded Bituminous Macadam Grading -I with VG-40 Bulk Bitumen Providing and Laying bituminous Concrete with higher capacity batch type hot mix plant using crushed aggregates of specified grading, premixed with bituminous binder @ 5.2 per cent of mix and filter , transporting the hot mix to work site , laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment , rolling with smooth wheeled , vibratory and tandem rollers to achieve the desired compaction as per MoRT&H specification clause no. 507 complete in all respests with VG-40 Bulk Bitumen.
309	Road Marking with Hot Applied Thermoplastic Compound with Reflectorising Glass Beads on Bituminous Surface (Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes.)
310	Cast-in-Situ Cement Concrete M20 Kerb (Construction of cement concrete kerb with top and bottom width 115 and 165 mm respectively, 250 mm high in M 20 grade PCC on M-15 grade foundation 150 mm thick, foundation having 50 mm projection beyond kerb stone, kerb stone laid with kerb laying machine, foundation concrete laid manually, all complete as per clause 409)
311	PCC M15 for Kerb Base
312	PCC M20 for Kerb cast in situ
313	PCC 1:3:6 in FoundationPlain cement concrete 1:3:6 nominal mix in foundation with crushed stone aggregate 40 mm nominal size mechanically mixed, placed in foundation and compacted by vibration including curing for 14 days.
314	sw gully trap
315	Carriage of materials from source to site work including loading & unloading all complete job as per specification and direction of E/I
316	Aggregate
317	Stone Metal
318	Brick
319	TOTAL AMOUNT FOR SCHEDULE ITEMS (A)
320	Non -Scheduled item
321	Supply and Fitting C.P. brass dish container medium quality with screw and hinges etc as per E/I.
322	Design, Supply, Installation, Testing & Commissioning of a complete Sewage Treatment Plant (STP) based on MBBR Technology with treated water suitable for gardening and flushing purposes.STP Capacity20 KLD (20,000 Liters Per Day)Technical Specifications:-1 STP Capacity- 20 KLD2 Treatment Technology- MBBR (Moving Bed Biofilm Reactor)3 Raw Sewage Quality- BOD up to 300 mg/l4 Treated Water Quality- BOD < 10 mg/l5 Equalization Tank- RCC/FRP6 Aeration Tank-MBBR Media Based7 Media Filling- 50% Filling Ratio8 Air Blower -2 Nos. (1 Working + 1 Standby)9 Filter Feed Pump- 2 Nos.10 Pressure Sand Filter- FRP Vessel11 Activated Carbon Filter-FRP Vessel12 Sludge Handling System- Sludge Drying Bed13 Disinfection System- Chlorination/UV14 Control Panel- Fully Automatic15 Interconnecting Piping- UPVC16 Electrical Cables- Copper Armoured17 Treated Water Tank - IncludedEquipment Details1. Equalization Tank* Capacity: 8,000 Liters* Air Mixing Arrangement* Level Controller2. MBBR Aeration Tank* High Surface Area Bio Media* Diffuser System* Aerobic Treatment Process3. Air Blowers* Capacity: 150 m³/hr* Duty/Standby Configuration4. Secondary Clarifier* Sludge Settlement System* Hopper Bottom Design5. Pressure Sand Filter* Multi Grade Sand Media* FRP Construction6. Activated Carbon Filter* Odor & Color Removal* High Grade Activated Carbon7. Disinfection Unit* Chlorination System* Residual Bacteria Control8. Electrical Control Panel* MCCB Protection* Auto/Manual Mode* Motor Protection SystemWarranty* 12 Months Warranty on Mechanical & Electrical Equipment.* Manufacturing Defects Covered. All Complete as per Engineer in Charge.
323	Supply, Installation, Testing & Commissioning of 1000 LPD ETC Type Solar Water Heating System complete with SS-304 insulated storage tank, ETC vacuum tubes, hot dip galvanized mounting structure, electrical backup heater, CPVC/GI insulated piping, valves, fittings, accessories, transportation, testing and commissioning as per technical specifications. Technical Specifications* Capacity : 1000 LPD* Collector Type : ETC (Evacuated Tube Collector)* ETC Tubes : 120 Nos.* Tube Size : 58 mm × 1800 mm* Storage Tank : SS-304 Stainless Steel* Insulation : 50 mm PUF* Outer Casing : Powder Coated GI* Mounting Structure : Hot Dip Galvanized Steel* Electrical Backup Heater : 6 kW* Water Temperature : 65°C to 85°C* Complete with valves, air vent, NRV, safety valve and accessories* Complete piping with insulation* Testing & Commissioning IncludedWarranty* Solar Water Heater System : 5 Years* Storage Tank : 5 Years* ETC Tubes : 5 Years* Structure : 5 Years
324	Chemical Earthing : Supply, errection, fitting, fixing, commissioning and testing along with earth cutting, digging, earth refilling for chemical earthing of the building except G.I. Strips (25mmX5mm) Each earth pit has to be tested with earth tester 1000 V/1000 Ohms & the test report has to be submitted by the contractor to the department after certification of the same by the consultant. The above chemical earthing includes the provision of masonary enclosure and HDPE Earth Pit Cover 300mm X 300 mm (Under-floor earth inspection pit) having locking arrangement as earth chamber.The above chemical earthing includes the following items (3 Mtr Earthing) Each chemical earthing shall have following details:- Supply of Pollution free Earthcon Compound 4 bags of 25 Kg each Supply of 17.2 mm dia, 250 micron,molecularly bounded copper coated 3 Mtr long electrode. Tested as per IEC 62561-2. Meets the requirement of IS 3043 & IEC 60364-5-54. Tested for short circuit withstanding capacity. High Tensile strength. (UL Listed).Supply of Stainless Steel \\"U\\" Bolt ClampSupply of HDPE Earth Pit Cover for earth chamber (Capacity of 5 ton)
325	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes joining of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of E/I. Exposed on Wall :40mm dia
326	Supply, Installation, Testing & Commissioning of HMV Simulator(OEM CABIN ) (VHN–5001)6 DOF Motion Simulator Features: ➢ 3-1 Software (car,truck,BUS) ➢ Life time software license ➢ Professional Driving Training ➢ Lessons Basic Driving (All controls , Gear , ignition ,blinker, Parking (City, Highway, mountain, FOREST )Day, Night, fog, snow, Rain ➢ Driving Track (8 TRACK REVERSE “S”, Parallel Parking , Upgrade Test”) ➢ Student Result Sheet with printout ➢ Customizable ROAD Side HORDING Logo and Message ➢ Navigation with satellite camera ➢ Voice guidance ➢ Customizable Welcome logo and Message ➢ Driver Data Base Management Real TRUCK Dashboard), ➢ combination switch, steering wheel, speedometer, ignition key ➢ Seat belt and parking brake indication ➢ H-Shifter gear box ( manual) ➢ Display screen( 43*3)LED/LCD TV /MONITER ➢ Real Truck type ABC pedals Truck with Oem CABIN Payload 1000kg 6 DOF Motion Simulator All Complete as per E/I
327	Supply, Installation, Testing & Commissioning of LMV SIMULATOR(Basic Simulator ) THREE SCREEN ( MODEL : VHN - 2002 or EQ) Features: ➢ Software (car, & truck) ➢ Life time software license ➢ Lessons Basic Driving (All controls , Gear , ignition ,blinker, Parking (City, Highway, mountain, FOREST )Day, Night, fog, snow, ➢ Driving Track (8 TRACK Parallel Parking ”) ➢ Student Result Sheet with printout with student photo ➢ Customizable ROAD Side HORDING Logo and Message ➢ Driver Data Base Store with report print ➢ Gear box (manual) ➢ Display Devices (3 no’s)22” full HD TV ➢ Alto car straining with ignition Key ➢ Seat belt and parking brake indication ➢ combination switch, steering wheel, speedometer, ignition key ➢ Multi-Language Voice (Hindi, English, Marathi etc) All Complete as per E/I
328	Supply, Installation, Testing and Commissioning of Air Compressor, 2 HP, 50 Liter Tank Technical SpecificationsType: Reciprocating, oil lubricated air compressorMotor Rating: Minimum 2 HP (1.5 kW)Power Supply: Single Phase, 220-240V AC, 50 HzAir Receiver Capacity: Minimum 50 LitresMaximum Working Pressure: Minimum 8 Bar (115 PSI)Free Air Delivery: Minimum 180 LPMCompressor Pump: Cast iron cylinder blockMotor Winding: 100% Copper WindingPressure Switch: Automatic Cut-In/Cut-OffSafety Valve: Factory calibratedPressure Gauges: Tank pressure and outlet pressure gaugesAir Regulator: Integrated pressure regulatorDrain Valve: Provided for tank moisture removalMobility: Mounted on wheels with carrying handleAccessories: Air hose, couplers and fittingsWarranty: Minimum 1 Year
329	Supply, Testing and Commissioning Puncture Repair Kit with Tyre Lever Technical SpecificationsSuitable for: Tubeless Car, Jeep and Light Commercial Vehicle TyresKit Contents:Spiral Probe Tool – 1 No.Insertion Needle Tool – 1 No.Repair Plugs/Strings – Minimum 20 Nos.Rubber Cement – 1 TubeValve Core Tool – 1 No.Valve Cores – Minimum 5 Nos.Tyre Levers – Minimum 2 Nos.Tyre Lever Material: Forged Carbon SteelLever Length: Minimum 300 mmStorage Case: Heavy-duty plastic carrying caseCorrosion Resistant Finish
330	Supply, Testing and Commissioning Heavy Duty Cross Wheel Spanner Technical SpecificationsType: Cross Wheel BraceMaterial: Forged Chrome Vanadium SteelFinish: Chrome PlatedSocket Sizes:17 mm19 mm21 mm23 mmOverall Length: Minimum 350 mmSuitable for Passenger Cars and Light Commercial VehiclesCorrosion Resistant Construction
331	Supply, Testing and Commissioning Hydraulic Trolley Jack, 3 Ton Technical SpecificationsType: Hydraulic Trolley JackSafe Working Capacity: Minimum 3 TonMinimum Lifting Height: Not more than 140 mmMaximum Lifting Height: Minimum 500 mmConstruction: Heavy-duty welded steel frameWheels:Rear Swivel Castor WheelsFront Steel WheelsSafety Features:Overload Protection ValveControlled Lowering SystemHandle: Two-piece detachable operating handleFinish: Powder coated
332	Supply, Testing and Commissioning of Digital Tyre Pressure Gauge Technical SpecificationsDisplay Type: Digital LCD with BacklightMeasuring Range:0 – 150 PSI0 – 10 BarAccuracy: ±1 PSI or betterResolution: 0.1 PSIAuto Shut-Off FunctionBattery OperatedProtective Rubber CoverSuitable for Cars, Motorcycles and Commercial Vehicles
333	Supply, Testing and Commissioning of Heavy Duty Lever Type Grease Gun Technical SpecificationsType: Lever Operated Grease GunBarrel Capacity: Minimum 400 gmWorking Pressure: Minimum 4,000 PSIMaterial: Steel Barrel ConstructionFlexible Hose Length: Minimum 300 mmCoupler: Hydraulic TypeLoading Method:CartridgeBulk FillErgonomic Handle Grip
334	Supply, Testing and Commissioning of Fixed Spanner Set (Metric) Technical SpecificationsType: Double Open-End Spanner SetMaterial: Chrome Vanadium SteelFinish: Mirror Chrome FinishMetric Sizes:6×7 mm8×9 mm10×11 mm12×13 mm14×15 mm16×17 mm18×19 mm20×22 mm24×27 mm30×32 mmHeat Treated and HardenedSupplied in Storage Roll Pouch
335	Supply, Testing and Commissioning of Box Spanner Set Complete Technical SpecificationsMaterial: Chrome Vanadium SteelType: Tubular Box Spanner SetSize Range: 6 mm to 32 mmComponents:Box SpannersTommy BarsExtension RodsFinish: Chrome PlatedStorage Case IncludedSuitable for Automotive Workshop Use
336	Supply, Installation, Testing and Commissioning of Professional Pliers Set Technical SpecificationsMaterial: Chrome Vanadium SteelHeat Treated Cutting EdgesInsulated Ergonomic Grip HandlesSet ContentsCombination Plier – 8\\"Long Nose Plier – 8\\"Side Cutting Plier – 6\\"Water Pump Plier – 10\\"
337	Supply, Installation, Testing and Commissioning of Screwdriver Set (20 Pieces) Technical SpecificationsTotal Pieces: Minimum 20Blade Material: Chrome Vanadium SteelTip Type:FlatPrecision ScrewdriversMagnetic TipsAnti-Slip Ergonomic HandleStorage Case IncludedCorrosion Resistant Finish
338	Supply, Installation, Testing and Commissioning of Adjustable Spanner, 12 Inch Technical SpecificationsLength: 12 Inch (300 mm)Material: Forged Chrome Vanadium SteelFinish: Chrome PlatedMaximum Jaw Opening: Minimum 35 mmPrecision Worm Gear AdjustmentLaser Marked ScaleCorrosion Resistant
339	Supply, Testing and Commissioning of Ball Peen Hammer Technical SpecificationsType: Ball Peen HammerHead Weight: 900 ±100 gramsHead Material: Drop Forged Carbon SteelHardness: Heat Treated and TemperedHandle:Fiberglass CoreRubber GripAnti-slip DesignSuitable for Workshop Maintenance
340	Supply, Installation Testing and Commissioning of Automatic Battery Charger 12V/24V Technical SpecificationsInput Supply: 220-240V AC, 50 HzOutput Voltage:12V DC24V DCCharging Current: Minimum 20 AmpSuitable Battery Capacity: 20 Ah to 300 AhBattery Types Supported:Lead AcidAGMGel BatteriesAutomatic Charging and Float ModeProtection Features:Reverse Polarity ProtectionShort Circuit ProtectionOverload ProtectionOverheating ProtectionDigital Display for Charging StatusHeavy Duty Output Leads with Clamps
341	Supply, Testing and Commissioning of First Aid Box, Wall Mounted Technical SpecificationsType: Wall Mounted First Aid CabinetCabinet Material:Powder Coated MS Sheet or ABS PlasticDoor:LockableTransparent Viewing Panel PreferredSize: Minimum 450 mm × 300 mm × 150 mmMinimum ContentsAdhesive Bandages – 50 Nos.Sterile Gauze Pads – 20 Nos.Cotton Roll – 1 No.Antiseptic Solution – 100 mlBurn Ointment – 1 TubeAdhesive Tape – 2 RollsScissors – 1 No.Disposable Gloves – 10 PairsTriangular Bandage – 2 Nos.Crepe Bandage – 2 Nos.Eye Wash Bottle – 1 No.CPR Face Shield – 1 No.Instant Cold Pack – 1 No.First Aid Manual – 1 No.
342	Supplying & Placing Dual Desk, PLPB Edge Banded Top, Seat & Back,Powder Coated Pipe Frame, Top Size - 1050 X 400 X 18mm Thick Overall Size - 1050 X 980 X 750 Material of Desk Top +/- 2 mm (For shelf / storage +/- 4 mm) 20 mm thick MDF Board of grade SBG II conforming to IS 12406 laminated with minimum 0.6 mm thick on Top side of type S, P or F having index 3.2.3 conforming to IS 2046 and minimum 0.5 mm thick balancing laminate on the other side Material of Support Structure or Side Pannel Mild Steel square Section of size 25x25 mm and wall thickness minimum 1.6 mm Height of Desk Top in mm (±5 mm) 750 Width of Desk Top in mm (± 5 mm) 450 TYPE OF DESKING INTEGRATED DESK CUM SEATING WITH SHELF / STORAGE UNDER DESK Desking Configuration TWO SEATER Length of Desking, Seating and Backrest (if provided) in mm (±10 mm) 1050 Material of Seat and Backrest (if provided) (+/- 2 mm (For back rest +/- 4 mm) 20 mm thick MDF Board of grade SBG II conforming to IS 12406 laminated with minimum 0.6 mm thick on Top side of type S, P or F having index 3.2.3 conforming to IS 2046 and minimum 0.5 mm thick balancing laminate on the other side Material of Support Structure Mild Steel square Section of size 25x25 mm and wall thickness minimum 1.6 mm Material of Seat Cushion WITHOUT CUSHION Width of Seating in mm (±10 mm) 300 Height of Seat in mm (±10 mm) 460 Width of backrest if provided in mm (± 5 mm) 200 Back Support for Seating of Same materail as Seating Provided without cushion
343	Supplying & Placing Three Seater Desk, PLPB Edge Banded Top, Seat & Back, Powder Coated Pipe Frame, Top Size - 1500 X 400 X 18mm Thick Overall Size - 1500 X 980 X 750 Material of Desk Top +/- 2 mm (For shelf / storage +/- 4 mm) 18 mm thick prelaminated Particle Board Material of Support Structure or Side Pannel Mild Steel Pipe of diameter 25 mm and wall thickness 1.1 mm minimum Height of Desk Top in mm (±5 mm) 750 Width of Desk Top in mm (± 5 mm) 400 TYPE OF DESKING INTEGRATED DESK CUM SEATING Desking Configuration THREE SEATER Length of Desking, Seating and Backrest (if provided) in mm (±10 mm) 1050 Material of Seat and Backrest (if provided) (+/- 2 mm (For back rest +/- 4 mm) 18 mm thick prelaminated Particle BoardMaterial of Support Structure Mild Steel Pipe of diameter 25 mm and wall thickness 1.1 mm minimum Material of Seat Cushion WITHOUT CUSHION Width of Seating in mm (±10 mm) 450 Height of Seat in mm (±10 mm) 460 Width of backrest if provided in mm (± 5 mm) 200 Back Support for Seating of Same materail as Seating back support not provided
344	Supplying & Placing 1200 mm x 610 x Executive computer table Type of Computer Table Computer table with key board drawer and table top Construction of Computer/Printer Table Gable end and modesty panel Colour of Top As per Buyer's Choice Material of table top,keyboard and drawer Three layer prelaminated particle board(Wood Product) of grade II type II of IS 12823/Latest Gable end and Modesty panel material Three Layer prelaminated particles board(wood product) of grade II type III of IS 12823/Latest Leg Material NO LEGS Table top thickness ±2mm 19 millimeter Thickness of gable end and modesty panel ±2mm 19 Dimension of leg(mmXmm) ±5mm No legs Length of table in mm (±15 mm) 1200 millimeter Depth of table in mm (±10mm) 610 millimeter Height of table in mm (±10mm) 760 millimeter Type of keyboard tray Wooden keyboard tray Material of footrest No footrest Material thickness of footrest ±2mm No footrest Product having BIFMA certification YES OEM of offered product is ISO 9001:2015 certified YES OEM of offered product is ISO 14001:2015 certified YES OEM of offered product is ISO 18001:2007/45001:2018certified YES
345	Supplying and PlacingWriting Board 1200mm x 3000mm Purpose : Writing Mounting type : Wall mounts Frame (All round framing) : With, Writing board placed Top Surface materials (Usedfor white board surface) : Porcelain Top surface material thickness : 0.7 mm to 0.8 mm Frame material :Anodized extruded aluminum alloy hollow section conforming to IS 733
346	Supplying & Placing Executive Table, Particle Board Top W1600 X D1600 X H750 Structure /Frame of table Gable end and modesty panel The type of Storage provided One side E.R.U unit Keyboard tray Not provided Footrest Not Provided Tabletop Material Commercial Block Board MR Grade Conforming to IS 1659 Thickness of table top material (± 1 mm) 36 mm Gable end material Prelaminated particles board(wood product) of grade II type III of IS 12823/Latest The thickness of the gable end NA Modesty panel material Perforated MS sheet The thickness of the modesty panel material 0.9 mm (for metal sheet) Leg Material Mild Steel (MS) ERW The thickness of the Leg material 1.2 mm Width of tabletop ±10 mm 1500 mm Depth of table ±10 mm 915 mm Height of table ±10 mm 750 mm Size (L x W) /diameter of leg material ± 5 mm NA ERU unit consists of 3 drawers Total Number of drawers /storage in Pedestal units Four drawers Table top finish Laminate in color with swede finish 0.6-0.8mm thickness of type S, F or P having index no.3.2.3 conforming to IS 2046/Latest with having balancing laminate of 0.5mm thick on another side Tabletop shade Oxford cherry Table /ERU /Pedestal Panel Plain Side Edge to be banded with PVC tape 2 mm thick with the help of hot melt glue
347	Supplying & Placing Medium Back Chair, Chrome Plated Pipe PU Arm, Gas Lift, Chrome Base, Mesh Back & Seat Net Tapestry Chair mechanism Tilt working with torsion bar mechanism Type of locking Upright locking Number of arm movement N.A Pedestal Base Chrome plated MS Armrest Material Polypropylene Seat material Pressed and moulded with PU foam Backrest is made of One piece hot pressed plywood with PU foam Density of PU foam used in seat KG per Cu Meter (± 3) 40 Density of PU foam used in backrest in KG per Cu Meter (±3) 40 Backrest upholstered with 100% Polyester Fabric Seat upholstered with 100% polyester fabric GSM/Thickness of fabric ±5%(Gram/Square meter) 220 gram Overall width (±10 mm) 650 mm Backrest Height ±15 mm 690 mm Backrest Width ±10 mm 440 mm Seat Height ±10 mm 440 mm Seat Width ±10 mm 480 mm Seat Depth ±10 mm 480 mm Thickness of MS Plate Joining the under structure with Seat 5 mm Thickness of Plywood used in Seat ±1(mm) 12 mm Thickness of Plywood used in Backrest ± 1(mm) 12 mm Pedestal Size (Diameter in mm) ±10 mm 600 mm Thickness of Polyurethane Foam Used in Seat in mm (±2 mm) 30 mm Thickness of Polyurethane Foam Used in Backrest in mm((±2 mm) 35 mm
348	Supplying & Placing Visitor Chair, Cushion Arm, PU Moulded Seat Back, Chrome Plated Pipe stand Leatherette Tapestry Chair Type Non-Revolving and Non-Tilting chair with Armrest Chair frame type LegsArmrest type Continuous armrest Seat type Padded Backrest type Padded Frame Material Configuration Two Piece Frame material Stainless Steel (SS 202) Seat material Moulded Plywood Seat material thickness 30 mm Density of Polyurethane foam used in seat (±2 Kg/Cub Meter) 40 Seat upholstered with PU sheet GSM of seat cover (± 3 GSM) 390 GSM Backrest material Moulded Plywood Density of Polyurethane foam used in Backrest ( ±2 Kg/Cub Meter) 32 Backrest upholstered with PU sheet Seat Depth (± 5 mm) 430 mm Seat Width (± 5 mm) 460 mm Seat height from floor surface (± 5 mm) 475 mm Backrest width (± 5 mm) 450 mm Backrest height from seat (± 5 mm) 460 mm Paint Type Chrome Paint Polish Type N.A Colour of Paint N.A Availability of Test Report from Central Govt/NABL/ILAC accredited lab to prove the conformity of product to the Specification Yes Test reports to be furnished to buyer on demand Yes
349	Supplying & Placing workstation table in completely knock down conditions with an overall size 4000mm X 1260mm X 1200mm that is to be assembled at site. The worktop shall be made up of back to back 25mm thick Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The top profile shall be in sharing base rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. A pullout keyboard trey shall be provided of 18mm thick Pre-laminated particle board having size 550mm X 280mm. The trey shall be operated on keyboard channel. The top shall be supported on particle board base gable end. The end wall of the top shall be topped by gable end. It should be made up of 25mm thick Pre-laminated particle board and the profile shall be in linear shape with appropriate PVC edge banding. The workstation shall have panel based partition of 60 mm thick with overall height 1200mm. The partition shall be linear in profile and provided in front side of user. The top trim, top bar, mid bar, vertical bar, raceway, skirting shall be made up of aluminium extrusions (pre-treated) and duly powder coated with 40-60µ thick. The trims shall have the size 60mm X 19mm with 1.5mm thick covered with Die cast end caps on joints 2 ways, 3 ways & 4 ways (L-cover for corner, T-cover for middle section wherever required). The aluminium raceway shall be situated below the worktop with an overall size 116mm(H) X 60mm(D) with 1.4 mm cover thickness and 2mm back thickness as per requirement of inlaying the electrical management and carrying the wire horizontally. The exposed vertical and horizontal faces of the frames shall be snap fitted with trims. There shall be soft-board (with fabric) provided at front of the user. Laminated bottom tile shall be situated below the work top. The Partition shall have concealed wire management capabilities and should be engaged for responsive and safe operations of power, telecommunications and data (LAN) and has separate components for electrical, data and telephone cables having adequate capability of both the vertical and horizontal wire movements. Slots/cut-outs should be given on raceways to fix all electrical and data points. Zinc coated small top support brackets shall be fixed on the partition for table top support. To protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be situated at bottom. Adjustable leveller shoe shall be provided at bottom of the partition to avoid scratches on the floor. Fixed pedestal shall be provided with an overall size 400mm X 450mm X 725mm. The pedestal shall be made up of Pre-laminated particle board of grade II of IS 12823. Pedestal side, back, top, facia shall be 18mm thick and drawer base shall be 9mm thick. The pedestal shall have 4 nos. of drawer having same size. The drawer shall be operated with SS handle and easily close & open with the assistance of roller channel to enable smooth operation. The drawer shall have central locking mechanism in which all the drawer shall be synchronized locked with one single key. To protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be provided at bottom. A nylon castor based CPU unit shall be provided with an overall size 470mm X 286mm with 18mm thick Pre-laminated particle board. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification. The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380.
350	Supplying & Placing Medium Back Chair, PP Arm, Gas Lift, Nylon Base, PU Moulded Seat & Back, PP Seat & Back Cover, Fabric Tapestry Chair mechanism Centre pivot mechanism Type of locking Tilt limiter Number of arm movement N.A,Pedestal Base Chrome plated MS Armrest Material Polypropylene Seat material Pressed and moulded with PU foam Backrest is made of One piece hot pressed plywood with PU foam Density of PU foam used in seat KG per Cu Meter (± 3) 45 Density of PU foam used in backrest in KG per Cu Meter (±3) 40 Backrest upholstered with 100% Polyester Fabric Seat upholstered with 100% polyester fabric GSM/Thickness of fabric 5%(Gram/Square meter) 290 gram Overall width (±10 mm) 590 mm Backrest Height ±15 mm 600 mm Backrest Width ±10 mm 480 mm Seat Height ±10 mm 460 mm Seat Width ±10 mm 460 mm Seat Depth ±10 mm 410 mm,Thickness of MS Plate Joining the under structure with Seat 0.3 mm Thickness of Plywood used in Seat ±1(mm) 12 mm Thickness of Plywood used in Backrest ± 1(mm) 12 mm Pedestal Size (Diameter in mm) ±10 mm 600 mm Thickness of Polyurethane Foam Used in Seat in mm (±2 mm) 30 mm Thickness of Polyurethane Foam Used in Backrest in mm((±2 mm) 30 mm
351	Supplying & Placing Conference table in completely knock down conditions with an overall size 3600mm X 1200mm X 750mm that is to be assembled at site. The construction of the main table shall be free standing structure constructed with the help of minifix dowels and pins. The table top shall have the size 1800mm X 1200mm made up of 2 nos. of 50mm thick pre-laminated particle board of grade II of IS 12823 with one side laminate and finish as per approved shade. The table top profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edgebander machine at 200 0C. The table top shall be supported by particle board base gable end. The end wall of the table on the side shall be topped by gable end. The gable end shall have the size 1050mm X 695mm with 49mm thick and 100mm X 695mm with 18mm thick. The gable end shall be made up of Pre-laminated particle board with appropriate PVC edge banding and covered both side by Aluminium section. The table shall be clad with 18mm thick modesty panel which provide structural support for the desk. The modesty panel shall have an overall size 1200mm X 400mm with 18mm thick pre-laminated particle board connected with both end. There shall be buffers provided to avoid scratches on the floor. The table connections have to be made in such a way that no gap should be seen in between. The manufacturershall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification.The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380.
352	Supplying & Placing 3 Seater Sofa With SS Arms & Legs, Perforated Seat & Back, Powder Coated Beam Size in mm - 1750(L) X 710(D) X 755(H) SS 304 Style with arm and backrest Seating Capacity (Nos) 3 Material of Main Frame SS 304 Material of Seat and Backrest SS 304 Material of Arms SS 304 Material of Legs SS 304 Material of Side Bar Bracket made up of chrome plated solid steel Overall Length in mm (±10 mm) 1800 Overall Depth in mm ( ±5 mm) 665 Overall Height in mm (±5 mm) 760 Conforming to International Standard for Public Seating (*BIFMA X 5 dot 4 or equvalent) YES All steel component to be epoxy powder coated 60 micron thick
353	Supplying & Placing Modular table in completely knock down conditions with an overall size 2650mm X 2200mm X 750mm that is to be assembled at site. The worktop shall have the size 2200mm X 1000mm x 76mm thick made up of Medium Density Fibre-board with approved veneer laminate and PU polish accordingly. The table top profile shall be in rectangle shape with round corners and full round post forming edges. The table top shall be supported on MDF board based gable end. The end wall of the table on the side shall be topped by gable end. It should be made up of 76mm thick medium density fibre-board and profile shall be in moulded construction with full round post forming edges and duly deco painted. The table shall be clad with 18mm thick modesty panel which provide structural support for the table. It should be 18mm thick medium density fibre-board in linear shape with appropriate PVC edge banding and veneer laminate. There shall be buffers provided at the base to avoid scratches on the floor. The table shall have side unit for storage purpose with an overall size 2200mm x 600mm X 600mm. It shall have 2 nos. of drawer, 1 nos. of filling space with door and 1 nos of open space . The drawer shall be operated with profile handle and easily close & open with the assistance of sliding channels to enable smooth operation and sliding rail track and concealed crank hinge. Drawer facai, sides and all other shall be made in 18mm thick and drawer base shall be 9mm thick. To protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be provided at bottom. The complete structure shall be supplied with approved veneer laminate, PU polish and deco painted. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification.
354	Supplying & Placing High Back Chair, SS Wooden Arm, Synchro Knee Tilt, Gas Lift, Die Cast Aluminium Base Pure Leather Chair mechanism Knee tilt Synchronic mechanism Type of locking 5-Position LockingNumber of arm movement N.A Pedestal Base Aluminium die cast Armrest Material MS chrome plated Seat material Pressed and moulded with PU foam Backrest is made of One piece injection moulded frame Density of PU foam used in seat KG per Cu Meter (± 3) 35 Density of PU foam used in backrest in KG per Cu Meter (±3) 35 Backrest upholstered with Pure Leather Seat upholstered with Pure leather GSM/Thickness of fabric ±5%(Gram/Square meter) N.A Overall width (±10 mm) 550 mm Backrest Height ±15 mm 500 mm Backrest Width ±10 mm 440 mm Seat Height ±10 mm 480 mm Seat Width ±10 mm 460 mm Seat Depth ±10 mm 430 mm Thickness of MS Plate Joining the under structure with Seat 0.3 mm Thickness of Plywood used in Seat ±1(mm) 18 mm Thickness of Plywood used in Backrest ± 1(mm) 12 mm Pedestal Size (Diameter in mm) ±10 mm 620 mm Thickness of Polyurethane Foam Used in Seat in mm (±2 mm) 35 mm Thickness of Polyurethane Foam Used in Backrest in mm((±2 mm) 40 mm
355	Supplying & Placing Visitor Chair, Wooden Frame, Chrome Cushion Arm, Chrome Plated Pipe Stand Pure Leather Chair Type Non-Revolving and Non-Tilting chair with Armrest Chair frame type CantileverArmrest type Moulded T armrest fitted with seat bottom Seat type Padded Backrest type Padded Frame Material Configuration Two Piece Frame material Stainless Steel (SS 304) Seat material Moulded Plywood Seat material thickness 18 mm Density of Polyurethane foam used in seat (±2 Kg/Cub Meter) 45 Seat upholstered with Leather GSM of seat cover (± 3 GSM) 250 GSM Backrest material Moulded Plywood Density of Polyurethane foam used in Backrest ( ±2 Kg/Cub Meter) 55 Backrest upholstered with Leather Seat Depth (± 5 mm) 470 mm Seat Width (± 5 mm) 520 mm Seat height from floor surface (± 5 mm) 455 mm Backrest width (± 5 mm) 510 mm Backrest height from seat (± 5 mm) 580 mm Paint Type Chrome Paint Polish Type As per Buyer’s Requirement (to be indicated during bid creation)
356	Supplying & Placing 3 Seater Sofa With Wooden Frame, Powder Coated Leg, Twin Colour Leatherette Tapestry Size in mm - 1930 (L) X 790 (D) X 850 (H) Total Number of Seats in the Sofa Set 3 Number of Single Seater Units (Nos) No Single Seater Unit Number of Two Seater Units (Nos) No Two Seater Unit Number of Three Seater Units (Nos) 1 Number of Four Seater Units (Nos) No Four Seater Unit Frame Covering Fully Upholstered Sofa Set is Foldable to use as bed No Backrest Cushion Material Foam Density of Cushion of Backrest Material (Kg/Cubic M) 32 Covering Material for Seat and Backrest Genuine Leather Frame Structure Material and size (±1 mm) 19 mm thick Commercial board Seat Cushion Material Foam Density of Cushion of Seat Material ±3 (Kg/Cubic M) 40 Type of Spring in the Base / Seating Eight way hand tied spring Length of Single Seater Units in mm (±5 mm) 508 Length of Two Seater Units in mm (±10 mm) 1100 Length of Three Seater Units in mm (±10 mm) 1850 Length of Four Seater Units in mm (±10 mm) 2640 Depth of Sofa Units in mm (±10 mm) 775,Sofa Height (Without Back Cushion) ±5 (mm) 430 millimeter Sofa Height (With Back Cushion) ±5 mm 845 millimeter Seat Cushion Length ±5 (mm) 525 Seat Cushion Width ±5 (mm) 710 Seat Cushion Thickness ±3 (mm) 210 Backrest Cushion Length ±5 (mm) 530 Backrest Cushion Width ±5 (mm) 530
357	Supplying & Placing Centre Table, 12mm Toughened Glass, MS Powder Coated 1200 X 600 X 450 Understructure Number of storage under top No storage Top material Tempered glass Frame material Other wood Dimension of Top (Length X Breadth, or Diameter) ±20mm 1194mmX584mm Height of centre table ±10 mm 460 millimeter Thickness of top material (+/-2 mm) 12 millimeter Thickness of frame material (+/- 1 mm) 12 millimeter
358	Supplying & Placing Steel Almirah, 2 Doors, 4 Adjustable Shelf, Thickness 0.8mm W900 X D 450 X H1830 Technical specification of Almirah steel Generally conforming to BIS specification IS: 3312:2021 (with latest amendment) Type of Almirah steel Almirah Steel shelving cabinets Number of door 2 Number of drawers required No Drawer Number of shelves 4 Colour of finish As per Buyer’s Requirement (to be indicated during bid creation) Steel sheet material CRCA sheets conforming to grade CRI of IS 513(part-1):2016 (with latest amendment) Sheet rounds and flats Conforming to grade E250 of IS 2062 Almirah height(excluding the height of pedestal) ± 5 mm 1980 mm Almirah width ± 5 mm 900 mm Almirah depth ± 5 mm 450 mm Side sheet thickness 0.8 mm Back sheet thickness 0.8 mm Top sheet thickness 0.8 mm Bottom sheet thickness 1 mm Shelves sheet thickness 0.9 mm Shelves supporting bracket thickness 1.6 mm Hinges sheet thickness 1.25 mm(double folded) Hanging rod wall thickness N.A Mirror frame sheet thickness N.A Mirror frame border width N.A Width of stiffener N.A Stiffener sheet thickness N.A Number of glass sheet fixed N.A Handle size 12 cm Steel Almirah lock/locker lock Six lever lock Material of lock Brass and Steel finish Finish coat with enamels Conforming to IS:151 Powder coating Conforming to IS: 13871
359	Supplying & Placing Dining/study Table, Powder Coated Pipe Frame, PLPB Edge Banded Top, 25 mm Thick, Size in mm - 1800 X 900 Shape of Table Rectangular Seating Capacity 6 Material of top Prelaminated board Material of understructure Powder Coated MS Material of top finish Mica Length of table ±10mm (Diameter in case of Round) 1800 mm Depth of table ±10mm 900 mm Thickness of top in mm (+/- 5%) 25 mm
360	Supplying & Placing Café Chair, Chrome Plated Pipe Frame, Leatherette Tapestry Chair Armrest Without Type of seat Ply Seat Cushion With Back Rest Cushion with Upholstery Leatherite Material of frame SS 304 Chair height (overall) ±10mm 880mm Backrest width ±10mm 425 Width of seat ±10mm 400 Depth of seat in mm (+/- 10 mm) 400 Height of seat in mm (+/- 5 mm) 400 Seat Finish Cushioned Exposed Wooden / Metal Parts Finish N.A
361	Supplying & Placing Steel Library Rack (Double Face), Thickness 0.8mm W940 X D600 X H2110 Type CLOSED FROM SIDES ONLY Number of Shelves/Compartments (Top / Ceiling Shelf - not to be counted) 4 Shelves Material 0.8 mm Thick MS Sheet Conforming to Commercial Quality CR-1, Grade 340 of IS 513 Depth in mm (±5 mm) 600 Width in mm (±5 mm) 915 Height in mm (±5 mm) 2000 Paint Powder coated
362	Supplying & Placing Drinking water palteform Approximate External Dimensions (WXDXH) 750 x 690 x 1420 mm Input Voltage 230 V AC (50 Hz) Power Rating (Max) 850 ± 10% Water Storage Tank Capacity 120 Litre Cooling Capacity 60 LPH Output Water Temperature 15°C±1°C Refrigerant HFC R 134 a Thermal Insulation for Storage Tank PUF No. of Faucets 3 Cold No. of Stages for Filter cum Purifier 7 Active Copper Zinc Booster Yes % of Purified Water Recovery 25% % Rejection of TDS 90% (Approx) Permeate (Purified Water) Production Capacity 50 LPH Storage Tank & Drain Tray Material SS 304 Outer Body Material rest CRCA Powder Coated Steel Front Panel SS 304 and Type of Product Construction Concealed Type of Installation Indoor Net Weight 92 Kg Operating Input Water Pressure 1.0 to 2.0 Kg/cm² Operating Temperature 10°C to 40°C Recommended Total Dissolved Solids in Input Water(TDS) 500 to 2000 ppm.(Max) Recommended Hardness in Input Water 300 ppm(Max) Recommended pH of Input Water 6.5 to 8.5 Allowable Chlorine Input Water 0.2 ppm (Max) Allowable Iron in Input Water 0.3 ppm (Max) Turbidity <5 NTU
363	Suplying and placing of Single bed, Size (min.) 1000(W)x2000(L)x450(H) Length - 2000-2100.0 mm X Width - 1000-1150.0 mm X Height - 450mm headboard 750- 900.0mm ,AIOTA ,BIFMA COMPLIANT, GREEN GUARD,SEDEX CERTIFICATE.
364	Supplying & Placing Stainless Steel Rectangular Dining Table with Round fixed Chair of specification:Table top / Chair seat / bench seat material:Stainless steel Grade 202 galvanized,Table top / Chair seat / bench seat thickness:0.8 mm,Leg material for Table and Chair/bench:Stainless steel Grade 202 galvanized,Wall thickness of Leg material (for Table and Chair/bench):0.8 mmSupport material for Table and Chair/bench:Stainless steel Grade 202 galvanized,Backrest material for Chair/bench:No backrest,Table - Chair/bench attaching material:MS ERW tubes conforming to IS : 7138 - latest,Product Configuration:Provision for 8 - persons,Mode of supply:Assembled Ready To Use,Table Foot rest:All four sides along the width and depth both.,Chair/bench back rest Without Support for Table top:Widthwise support,Number of support for Table top:1 no.,Support for chair/bench seat Depthwise support:Width of table ± 10 mm,:2150 for 8-seater,Chair/bench Leg size ± 2 mm:25 mm Dia,Size of support pipes/square sections (for table):25 mm (dia),Size of support pipes/square sections (for chair/bench):15 mm Dia
365	Supply, Installation, Testing and Commissioning (SITC) of Desktop Computer for Director, DTO and Medical Officer Rooms Detailed Technical SpecificationsProcessor: Intel Core i5 (13th Generation or higher) / AMD Ryzen 5 equivalentMinimum 10 Cores / 12 ThreadsBase Clock Speed: Minimum 2.5 GHzRAM: 16 GB DDR4/DDR5, expandable up to 32 GBStorage: 512 GB NVMe SSDGraphics: Integrated GraphicsMonitor: 22-inch Full HD LED Monitor (1920 × 1080)Keyboard: USB Standard KeyboardMouse: USB Optical MouseNetwork Interface: Gigabit Ethernet Port (10/100/1000 Mbps)Wireless Connectivity: Wi-Fi 6 and BluetoothOperating System: Windows 11 Professional (Licensed)Security: TPM 2.0Warranty: Minimum 3 Years OEM On-site Warranty
366	Supply, Installation, Testing and Commissioning (SITC) of Desktop Computer for Office Staff Detailed Technical SpecificationsProcessor: Intel Core i3 (13th Generation or higher) / AMD Ryzen 3 equivalentRAM: 8 GB DDR4Storage: 512 GB NVMe SSDMonitor: 21.5-inch Full HD LED MonitorKeyboard and MouseGigabit LAN PortWindows 11 Professional LicensedTPM 2.0 Security ModuleExpandable RAM up to 16 GB3 Years OEM On-site Warranty
367	Supply, Installation, Testing and Commissioning of Online UPS Detailed Technical SpecificationsCapacity: 1 kVATechnology: True Online Double ConversionInput Voltage Range: 110–300 V ACOutput Voltage: 230 V AC ±1%Backup Time: Minimum 20 Minutes at Full LoadPure Sine Wave OutputLCD Status DisplaySMF Maintenance Free BatteriesAudible and Visual AlarmBIS CertifiedWarranty: 2 Years
368	Supply, Installation, Testing and Commissioning of Multifunction Laser Printer Detailed Technical SpecificationsTechnology: Monochrome LaserFunctions: Print, Scan and CopyPrint Speed: Minimum 30 PPMResolution: Minimum 1200 × 1200 dpiDuplex Printing: AutomaticConnectivity: USB, Ethernet, Wi-FiA4 Paper Size SupportMonthly Duty Cycle: Minimum 20,000 PagesStarter Toner IncludedWarranty: 1 Year
369	Supply, Installation, Testing and Commissioning of Dual Band Wi-Fi Router Detailed Technical SpecificationsDual Band (2.4 GHz and 5 GHz)Wi-Fi 6 StandardMinimum 1200 Mbps Throughput4 Gigabit LAN PortsWPA2/WPA3 SecurityMU-MIMO TechnologyWeb Based Configuration
370	Supply, Installation, Testing and Commissioning of Smart Interactive Flat Panel Display, 75-inch, 4K UHD, 20-Point Multi-Touch, Android OS, Inbuilt Speakers, Screen Sharing, Wi-Fi, OPS Compatible, Wall Mount Included Detailed Technical Specification – Smart Interactive PanelDisplay Size: Minimum 75 InchesResolution: 4K UHD (3840 × 2160)Touch Technology: Infrared / Capacitive TouchTouch Points: Minimum 20 Simultaneous Touch PointsOperating System: Android 13 or latestRAM: Minimum 8 GBInternal Storage: Minimum 64 GBBrightness: Minimum 400 cd/m²Viewing Angle: 178°Inbuilt Speakers: Minimum 2 × 15 WConnectivity:HDMI × 3USB × 3USB Touch InterfaceLAN PortWi-FiBluetoothWireless Screen Sharing SupportWhiteboard and Annotation SoftwareOPS Slot for Windows PC IntegrationWall Mount Bracket IncludedBIS CertifiedOEM Warranty: Minimum 3 Years
371	Supply, Installation, Testing and Commissioning of Vision Testing Machine Technical SpecificationVisual Acuity Testing: Near and Distance VisionColor Vision Testing (Ishihara equivalent)Depth Perception TestingPeripheral Vision TestingVertical & Horizontal Phoria TestingBinocular Vision TestingGlare Recovery TestNight Vision ScreeningDigital or Optical TypeAdjustable HeadrestPower Supply: 230V ACCE/ISO Certified
372	Supply, Installation, Testing and Commissioning of Diagnostic Audiometer Technical SpecificationPure Tone AudiometryAir Conduction Range:125 Hz to 8000 HzIntensity Range:-10 dB to 120 dB HLManual and Automatic TestingLCD DisplayTDH HeadphonesData Storage CapabilityCalibration CertificateIEC/ISO Compliant
373	Supply, Installation, Testing and Commissioning of Professional Breath Alcohol Analyzer Technical SpecificationFuel Cell Sensor TechnologyMeasurement Range:0.000 to 0.400 %BACResponse Time:≤ 10 SecondsDigital DisplayRechargeable BatteryMemory StorageCalibration FacilityNon-contact or Mouthpiece TypeCE Certified
374	Supply, Installation, Testing and Commissioning of Digital Blood Pressure Monitor Technical SpecificationFully AutomaticOscillometric MeasurementSystolic Range:60–260 mmHgDiastolic Range:40–215 mmHgPulse MeasurementLarge LCD DisplayMemory FunctionWHO Classification Indicator
375	Supply, Installation, Testing and Commissioning of Pulse Oximeter Technical SpecificationSpO₂ Measurement:70–100%Pulse Rate:30–250 bpmAccuracy:±2%OLED DisplayAuto Power OffPortable Design
376	Supply, Installation, Testing and Commissioning of Height and Weight Measurement System Technical SpecificationDigital Weight Capacity:Minimum 200 kgAccuracy:±100 gIntegrated StadiometerHeight Range:70–210 cmBMI Calculation FacilityLCD DisplayHeavy Duty Platform
377	HT Cable-3Cx70 sqmm:- Supply of ISI marked aluminium cable conductor XLPE PVC insulated cable as per IS:7098 armoured, served, sheathed, 11kV grade.
378	Supply, Installation And Commissioning Of Automation Equipments For Driving Track AutomationVideo Analytics based Driving Testing System.Overview of functionality:1. Biometric` access system for electronic attendance registration.2. RFID access system will be provided for vehicles to enter the test track.3. Driving Track Automation software.4. Traffic lights control through track Automation software.5. Server unit for Driving Track Automation Software.6. Cameras and Poles for Video Analytics system7. Computers for registration and results.8. Voice Announcement system for track.9. Boom Barners to protect vehicle entry into track without permission.10. Surveillance system for track.11. Led Display boards to display track results and other instructions.
379	A. Automation Equipments and testing procedure for DTC:a. Traffic light Is set to green to give a signal to the driver to proceed. Boom barriers will open simultaneously on traffic signals turning green. Validation of driving through software using top View camera - start & drive tm the Track end to complete test.b. Validation to complete the serpentine in a straight position.c. Validation of reverse in “S” segment within a certain time without touching the edges or \\"H\\" Track.d. Validation to complete the '8' formation in a straight position.e. Validation to complete the traffic junction test following the traffic lights.f. Validation of parallel parking the car by reversing it in the bay within a certain time.g. Validation to complete the upgradient test by successfully driving over the ramp.h. Validation whether Vehicle is driven out of the lane using the camera.I. Validation of overall lane driving with result of pass & fall.j. Facial Verification of driver with registration form throughout the test.k. Seat Belt detection of driver throughout the test.I. Standard path followed by driver or not during test. m Database storage and access to measured data.n. Most of the equipment fulfills the \\"CE\\" or \\"FCC\\" requirement list.
380	B. Building or premises (Scope of customer/buyer}:a. Broadband connectivity.b. All types of civil work.c. Sign boards for track.d. Ladder for camera installation.e. Power backup LIKE DG SET.f. Local digging, concrete wor1<.s, zero grounding leveling, local fabrication, stand, frame etc.g. Unloading the goods from the transport vehicle on site.h. Provide electrician for electric work and electric goods like electric wireAnd switch etc. for Power points, conducted pipe for Ian and electric wiring to be used in track for installation.
381	Driving Test Parameters (LMV and HMV)Face Recognition and applicant identification - YesTest not attempted - YesTest Completed Partially - YesStandard Direction - YesReverse Detection - YesForward Detection - YesTest Duration (Start Time & End Time in seconds for each test) - YesVehicle Stoppage - YesVehicle out of Track Detection/ Kerb Hit Detection - YesAverage Speed - YesPlot 20 Test Path - YesThrough Smartphone /CameraApplicants face detection throughout test - YesSeat Belt detection throughout test - YesUse of Left, Right, Rear Mirror in Zig zag track and in Traffic Signal near zebra cross - YesDriving Test Parameters MotorcyclesFace Recognition and applicant identification (Note Smartphone will not be mounted on the vehicle) - YesTest Completed Partially - YesStandard Direction - YesLosing Balance (Vehicle falls detection) - YesResting foot on ground for more than 3 seconds - YesForward Detection - Yes Test Duration (Start Time & End Time in seconds) - YesVehicle Stoppage (For more than 3 to 4 seconds) - YesVehicle out of Track Detection I Kerb Hit Detection - YesAverage Speed - YesPlot 2D Test Path - YesVideo Data RetentionTest Video Data will be retained for a period of 60 days for evaluation purpose
382	Video Analytics Based Automated Driving Test Track with Video Recording (2-Wheeler, LMV and HMV)equipments for Automated Driving Test TrackL Cameras for Video Analytics (hlkvlslon 4MP/6MP camera with Vehicle detection technology)2. Server Computers (One Main and One Backup, Branded Workstation 1914th gen or higher with at least 12Gb/8Gb graphic card)3. Desktop Computers (i7/i5 Branded)4. Poles for Camera, Traffic lights and RFID (GI poles 5mtr/7mtr/8mtr/9mtr)s. Camera wiring to be used In Installation LAN cable/OFC (outdoor shielded)6. Boom Barrier with controller7. Traffic lights with controller as per Req8. Biometric Attendance Device9. LAN SWITCH 24 port with Rack10. 43-inch LED TV for viewing cameras Branded11. Mobile phones for driver photo capture and face detection12. NVR 32 channel (4 TB HOD)13. 2 TB Online storage server for one year (To Check re9Ult online)14. Color Printer for office15. Voice Announcement system for Track16. Led Display Boards for Test result 17. RFID Readers with controller18. Ml9C8llaneous Items like Junction box, connector, web cam etc.19. 8 channel POE switch20. Online UPS 10KVA single phase with l10lator (60 min back up)
383	Software for Automated Driving Test Track1. Desktop software for Track automation2. Online Registration software3. Online Result software4. Mobile application to record driver video inside car and face verification5. Online result PDF and Test videouploading6 Website for DTCLocal Installation and CommissioningPacking, Forwarding and Freight
384	1 Hardware Camera 6 MP Varifocal Bullet Network Camera with Al Technology 25 Nos Server Computer for automation Software HMV/LMV Processor i9 14th Gen or higher; 64gb Memory, 2TB SSD and 4TB HDD,8GB Graphic Card Nvidia T1000 3 Desktop Computer Intel® Core'\\" i7 Processors, 16gb memory, 1Tb SSD 2 NosGI Octagonal Poles With camera arm, foundation nut and bolt as per IS Standards 7Mtr/8Mtr/9Mtr 20 nos.Lan Cable Cat6 4 Pair UTP Double Sheath outdoor Cable 6100 Mtr Boom Barrier Boom Length 4+2 Mtr 200 mm Dia, Red + Green 2 Nos Traffic Lights Polycarbonate Enclosure Input: 12v DC With Mounting Clamp 4 nos.GI Poles for Traffic lights as per IS Standards 5Mtr 4 SetBiometric Attendance Device User Capacity: 5,000 (Fingerprint/Password/Card) Log Capacity 1,60,000 LCD Display Screen 2.4\\" TFT Color Screen Communication Interface: TCP/IP. USB, WI-Fl Operating Voltage: 12V/3A Access Control: Built-In Battery Back Up Built-In Cloud Supportable 1 nos.Giga Ethernet Switch 24 port 10/100/1OOOMbps ports 1 nos.Display 43 Inch LED Display 1 nos.
385	Mobile Phone Octa Core,8GB RAM 2 nos.32CH NVR 4K NVR with 8TB HOD 1 nos. Printer Pinter with WIFI 2 nos.HD Web camera Full HD Auto Light Balance 2 nos.Voice Announcement System Assembled (25W speakers, amplifier and mixer) 1 nos.Led Display Boards Outdoor Pl O Led Display with Wi-Fi/ Ethernet interface 1 nos.RFID Reader Reading Sensitivity 1~5M Reading Speed: Dual polarization reading, Reading Distance One label 64-bit ID number<6ms Antenna: Build-in circular polarization antenna gain 8dB/build-In linear polarization antenna, gain 12dBi Set 3Controller for RFID Reader, Traffic lights and Boom Barner Ethernet/Wi-Fi Based 4 channel controller 5 nos.POE Switch 8 PoE+10/100/1000Mbps RJ45Ports1 10/100/1000Mbps RJ45 Port 1 Gigabit SFP Slot 4 nos.Wi-Fi Router Long range Wi-Fi router up to 100 mtrs 2 nos.Online UPS 10KVA with isolator with 60 min battery backup 1 nos.Surveillance System for Track Up to 16 cameras with poles if required and 60 days backup 1 nos.Automaton SoftwareRegistration Portal Web Based Software 1 nos.Video Analytics Based Automation Software for HMV Desktop Software 1 nos.Video Analytics Based Automation Software for LMV Desktop Software 1 nos.Result management Portal Desktop Software 1 nos.Mobile Application Android App for Face Verification 1nosServices Hardware InstallationCamera Installation, Network Setup Pole Instillation, Hardware Setup and Installation as per requirement 1 nos.Miscellaneous Components as per requirement 1 nos.Miscellaneous Service Cost as per requirement 1 nos. Track related Service Thermal Painting throughout Track as per requirement 1 nos.Road Signage including branding as per requirement 1 nos.Traffic Light System other than automation as per requirement 1 nos.civil work control room 10' x 15' x 10' fully furnished as per requirement chamber laying and foundation as per requirement.
386	Add GST 18 %
387	Add Labour cess 1% Please Enable Macros to View BoQ information

Tender Documents

SR No	FileName	File Description
1	Click here to download tender document	Tender Documents
2	Click here to download tender document	Tender Documents
3	Click here to download tender document	Tender Documents
4	Click here to download tender document	Tender Documents

Also Visit

Tenders

Jharkhand Tenders

Construction Tenders

Building Construction Tenders

Building Work Tenders

Disclaimer

We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.

Top

Tender For Construction Of Institute Of Driving Training And Research (Idtr Tier-1) At Jamshedpur, East Singhbhum, East Singhbhum-Jharkhand

Tender Documents

Disclaimer

About Us

Services

Browse Tenders

For Sales Inquiry

Tender For Construction Of Institute Of Driving Training And Research (Idtr Tier-1) At Jamshedpur, East Singhbhum, East Singhbhum-Jharkhand

Tender Documents

Disclaimer

OTP Verification

About Us

Services

Browse Tenders

For Sales Inquiry

Connect With Us