|
| 1 | NOTE: Schedule 'A' Part - I to Part-X (II to IX are prepriced by MES), Bidders shall insert their lumpsum amount in Green coloured field under col-6 onlyENGINEERING PROCUREMENT AND CONSTRUCTION (EPC) FOR PROVISION OF MARRIED ACCOMMODATION FOR OFFICERS, SOs AND EPs AT MAYABUNDER, AS PER SCOPE DEFINED INCLUDING GRIHA 3 star rating, walk through, 3D model etc., all as stipulated in scope of work and other documents of the tender, complete, all as specified and directed. |
| 2 | CONSTRUCTION OF RCC RETAINING WALL OF 2M TO 3M HEIGHT AND 140RM LENGTH BY ANALYSIS, DESIGN, ENGINEERING, DETAILING AND STRUCTURAL DRAWINGS AS PER DBR DULY VETTED BY IIT / NIT AND APPROVED BY THE DEPARTMENT COMPLETE ALL AS SHOWN ON SITE PLAN. Note: In case of variation in length of retaining wall, the same shall be priced at Pro-rata for the revised length of wall |
| 3 | CONSTRUCTION OF RCC RETAINING WALL OF 3M TO 4M HEIGHT AND 250RM LENGTH BY ANALYSIS, DESIGN, ENGINEERING, DETAILING AND STRUCTURAL DRAWINGS AS PER DBR DULY VETTED BY IIT / NIT AND APPROVED BY THE DEPARTMENT COMPLETE ALL AS SHOWN ON SITE PLAN. Note: In case of variation in length of retaining wall, the same shall be priced at Pro-rata for the revised length of wall |
| 4 | CONSTRUCTION OF RCC RETAINING WALL OF 4M TO 5M HEIGHT AND 420RM LENGTH BY ANALYSIS, DESIGN, ENGINEERING, DETAILING AND STRUCTURAL DRAWINGS AS PER DBR DULY VETTED BY IIT / NIT AND APPROVED BY THE DEPARTMENT COMPLETE ALL AS SHOWN ON SITE PLAN. Note: In case of variation in length of retaining wall, the same shall be priced at Pro-rata for the revised length of wall |
| 5 | CONSTRUCTION OF RCC RETAINING WALL OF 5M TO 6.5M HEIGHT AND 70RM LENGTH BY ANALYSIS, DESIGN, ENGINEERING, DETAILING AND STRUCTURAL DRAWINGS AS PER DBR DULY VETTED BY IIT / NIT AND APPROVED BY THE DEPARTMENT COMPLETE ALL AS SHOWN ON SITE PLAN. Note: In case of variation in length of retaining wall, the same shall be priced at Pro-rata for the revised length of wall |
| 6 | Lumpsum price worked out by the contractor for \\"SITE CLEARANCE, LAND DEVELOPMENT, EXCAVATION, EARTH WORK FOR PROVISIONAL ITEMS\\" as listed in Schedule \\"A\\" Part – II |
| 7 | Lumpsum price worked out by the contractor for \\"TOE WALL\\" as listed in Schedule \\"A\\" Part – III |
| 8 | Lumpsum price worked out by the contractor for \\"EXTERNAL WATER SUPPLY\\" as listed in Schedule \\"A\\" Part – IV |
| 9 | Lumpsum price worked out by the contractor for \\"EXTERNAL ELECTRIC SUPPLY\\" as listed in Schedule \\"A\\" Part – V |
| 10 | Lumpsum price worked out by the contractor for \\"ROAD / PATH / CULVERT\\" as listed in Schedule \\"A\\" Part – VI |
| 11 | Lumpsum price worked out by the contractor for \\"AREA DRAINAGE\\" as listed in Schedule \\"A\\" Part – VII |
| 12 | Lumpsum price worked out by the contractor for \\"SEWAGE DISPOSAL\\" as listed in Schedule \\"A\\" Part – VIII |
| 13 | Lumpsum price worked out by the contractor for \\"LIGHTNING PROTECTION\\" as listed in Schedule \\"A\\" Part – IX |
| 14 | Schedule \\"A\\" Part - X [Miscellaneous Items] [Tenderer has to quote unit rate under Col 6]Supply, Install, testing and commissioning of self priming centrifugal monoblock pump set of capacity 15 HP, with impeller of stainless steel power rating 11kW with discharge of minimum 6.7 LPS @ 80m Head, 3000 rpm inclusive all fittings, with starter including fixing on 'C' channel grouted in PCC foundation complete all as specified and directed.Make : Crompton, model No. PUM.CEN.720714437, MIN 15.2-72 or equivalant in Kirloskar / Beacon / KSB / Wilo Mather /Jyoti / V Guard.Note : PCC Foundation will be measured and paid separately |
| 15 | Supply and fix Cast iron Air valve with single air Outlet, conforming to IS 14845-2000 of size 50mm and fixng up in DI pipe water supply mains of size 100mm dia complete all as specified and directed. |
| 16 | S & F DI pipe k-9 (all socketed or socket and spigotted / flanged ) 100 mm dia. all as specified, conforming to IS : 8329-2000 with socket and spigot ends confirming to IS-8329, including rubber gasket tyton ring joints complete all as specified and directed. |
| 17 | M & L for DI specials such as bends (any type radius and angle) tapers and type (straight bends increasing or decreasing or double socket etc.,) tee places single trench, double branch cross, tail pieces, reducers (all sockets and spigoted/flanged) collars caps and plugs suitable for 100 mm dia pipes all as specified and directed. |
| 18 | S & F CI Foot Valve conforming to IS 4038-1986, 100 mm dia complete all as specified and directed. |
| 19 | Construction of masonry valve chamber of internal size: 1000mm x 1000mm x 1000mm, foundation 100 mm thick using PCC 1:4:8, type D-2, over 15cm thick hard core, 20cm thick solid block masonry with blocks cast using PCC 1:3:6, type C-1, set in cement mortar 1:4, plaster to internal surfaces 15mm thick and external surfaces up to 15cm below ground level and top of floor in cement and sand mortar 1:4, finished even and smooth with out using extra cement , MS sheet cover 3.15mm thick including 50mm x 50mm x 6mm thick MS angle frame fixed in PCC 1:2:4, type B1, coping with 25mm x 6mm flat iron hold fasts, handle, hinges with locking arrangements, applying one coat of red oxide primer and two coats of synthetic enamel paint to all steel surfaces and earth work in any type of soil including disposal of surplus soil to a distance not exceeding 50M complete all as specified and directed. |
| 20 | S & F DWC pipe of size 110mm outer dia. and 95mm inner dia. for protection including coupler, bends etc., IS marked for LT cable of size 300/120/95 sqmm complete all as specified and directed. |
| 21 | S&F DWC pipe of size 63mm outer dia. and 50mm inner dia for protection including coupler, bends etc., IS marked for LT cable of Size 70/35/25/16/10 sqmm.complete all as specified and directed. |
| 22 | Supply, install, testing and commissioning Out door type of factory fabricated LT panel made out of 3.15 mm thick CRCA sheet and angle iron of suitable size, floor mounted type with alluminium bus bar of capacity 600 Amp- 4 Nos including two coats of spray synthetic enamel paint over a coat of red oxide, including voltmeter, ammeter, with necessary CTs & PTs, selector switches, phase indication lamps for three phase system, control panel & power panel wiring, cable alleys at both side, confirming to IS:8623, IEC:60439 & CPRI Approved, protection class IP65 with the accessories including PCC foundation, housing with the following switch gears:- (a) MCCB 4 pole 400 Amps 50 KA - 01 Adjustable type compete with Overload protection, No load thermal based release [Incoming](b) MCCB 4 pole 160 Amp 35 KA - 03 Adjustable type compete with Overload protection, No load thermal based release [Outgoing](c) MCCB 4 Pole 125 amps 35 KA - 02 Adjustable type compete with Overload protection, No load thermal based release [Outgoing](d) MCCB 4 Pole 32 amps 25 KA - 02 Adjustable type compete with Overload protection, No load thermal based release [Outgoing] |
| 23 | Supply, install, testing and commissioning Out door type of factory fabricated LT panel made out of 3.15 mm thick CRCA sheet and angle iron of suitable size, floor mounted type with alluminium bus bar of capacity 300 Amp- 4 Nos including two coats of spray synthetic enamel paint over a coat of red oxide, including voltmeter, ammeter, with necessary CTs & PTs, selector switches, phase indication lamps for three phase system, control panel & power panel wiring, cable alleys at both side, confirming to IS:8623, IEC:60439 & CPRI Approved, protection class IP65 with the accessories including PCC foundation, housing with the following switch gears:- (a) MCCB 4 pole 125 Amps 35 KA - 01 Adjustable type compete with Overload protection, No load thermal based release [Incoming](b) MCCB 4 pole 63 Amp 25 KA - 04 Adjustable type compete with Overload protection, No load thermal based release [Outgoing](c) MCCB 4 pole 32 Amp 25 KA - 02 Adjustable type compete with Overload protection, No load thermal based release [Outgoing] |
| 24 | Supply, install, testing and commissioning Out door type of factory fabricated LT panel made out of 3.15 mm thick CRCA sheet and angle iron of suitable size, floor mounted type with alluminium bus bar of capacity 300 Amp- 4 Nos including two coats of spray synthetic enamel paint over a coat of red oxide, including voltmeter, ammeter, with necessary CTs & PTs, selector switches, phase indication lamps for three phase system, control panel & power panel wiring, cable alleys at both side, confirming to IS:8623, IEC:60439 & CPRI Approved, protection class IP65 with the accessories include PCC foundation housing with the following switch gears:- (a) MCCB 4 pole 160 Amps 35 KA - 01 Adjustable type compete with Overload protection, No load thermal based release [Incoming](b) MCCB 4 pole 63 Amp 25 KA - 04 Adjustable type compete with Overload protection, No load thermal based release [Outgoing](c) MCCB 4 pole 32 Amp 25 KA - 03 Adjustable type compete with Overload protection, No load thermal based release [Outgoing] |
| 25 | Supply, install, testing and commissioning Out door type of factory fabricated LT panel made out of 3.15 mm thick CRCA sheet and angle iron of suitable size, floor mounted type with copper bar of capacity 300 Amp- 4 Nos including two coats of spray synthetic enamel paint over a coat of red oxide, including voltmeter, ammeter, with necessary CTs & PTs, selector switches, phase indication lamps for three phase system, control panel & power panel wiring, cable alleys at both side, confirming to IS:8623, IEC:60439 & CPRI Approved, protection class IP65 with the accessories including PCC foundation, housing with the following switch gears:- (a) MCCB 4 pole 160 Amps 35 KA - 01 Adjustable type compete with Overload protection, No load thermal based release [Incoming](b) MCCB 4 pole 63 Amp 25 KA - 06 Adjustable type compete with Overload protection, No load thermal based release [Outgoing] |
| 26 | Supply, install, testing and commissioning Out door type of factory fabricated LT panel made out of 3.15 mm thick CRCA sheet and angle iron of suitable size, floor mounted type with alluminium bus bar of capacity 300 Amp- 4 Nos including two coats of spray synthetic enamel paint over a coat of red oxide, including voltmeter, ammeter, with necessary CTs & PTs, selector switches, phase indication lamps for three phase system, control panel & power panel wiring, cable alleys at both side, confirming to IS:8623, IEC:60439 & CPRI Approved, protection class IP65 with the accessories including PCC foundation, housing with the following switch gears:- (a) MCCB 4 pole 63 Amps 25 KA - 01,Adjustable type compete with Overload protection, No load thermal based release [Incoming](b) MCCB 4 pole 32 to 40 Amp 25 KA - 02 Adjustable type compete with Overload protection, No load thermal based release [Outgoing](c) Star Delta Starter 3 phase upto 15 HP - 02 Nos |
| 27 | Supply and lay cable XLPE Insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 33000 Volts, 3 core, 95 sqmm grade with stranded aluminium conductor, laid in trenches / passing through pipe / duct / road crossing / fixed on poles / walls and connecting up with suitable glands, lugs, nuts and bolts and testing on completion all as specified and directed. |
| 28 | S&F cable End Termination kit, heat shrinkable, outdoor type suitable for 33 KV, 95 sq.mm XLPE, 3 core power cable with aluminium conductor complete all as specified and directed. |
| 29 | S&F cable End Termination kit, heat shrinkable, indoor type suitable for 33 KV, 95 sq.mm XLPE, 3 core power cable with aluminium conductor complete all as specified and directed. |
| 30 | Supply, install, testing and commissioning of distribution transformer stepdown, outdoor type, 250 KVA, 3 Phase, 50 C/S Oil immersed, Naturally cooled, Outdoor type Step-Down Transformer having a No load voltage ratio 33000/433V, Vector group Dyn 11 with +/- 2 1/2 +/- 5, +/- 7 1/2 % Tapping as under taken out on the H.T. side and connected to externally hand operated 33 KV OFF circuit tap changing switch H.T winding connected in delta & LT winding connected in star and the neutral brought out & connected to a separate terminal for earthing with outdoor open porcelain bushing on H.V. side & Cable box on LV. side with the temperature rise not exceding 40 degree Centigrade by the thermometer in oil and 45 degree centrgrade by resistance & ambient temperature 45 degree centirgrade with first filing of oil conforming to IS-1180 : 2014, Level 2 with latest amendment including PCC / Brick Masonry Foundation / Platform as per IE Rules, fixing HT / LT Bush bar axial cables etc., complete all as specified and directed and comprising of the following Technical specification and fittings:(a) Ref standards : IS:1180(2014) Part-I & latest Energy efficient level-II (Amendment No 4)(b) installation : Outdoor(c) Rated Capacity KVA : 250KVA(d) Voltage at HV : 33000V(e) Voltage at LV : 433V(f) No of phases HV/LV : 3 (R.Y.B) / 3 + 1 (r,y,b + n) (g) Mehtod of Cooling : ONAN(h) Connections HV/LV : Delta/Star |
| 31 | Sl. Item No.29 (Contd…)(j) Vector Group : Dyn-11(k) Winding material : EC grade copper (Purity 99.99%) (l) Tapping % (Off Circuit): + 2 1/2 + 5 + 7 1/2 %(m) Insulation Class : 'A'(n) Temerature Rise : 40/45 degree centirgrate(o) Lossed @ 50% : 989 Watts(p) Losses @ 100% : 2903 Watts(q) % Impedance : 4.50% Fittings and accessories:- [a] 33 KV Externally hand operated Off Circuit Tap Changing Switch.[b] Oil Conservator Tank with drain plug and filling Cap. [c] Silka gel Dehydrating breathe charged with Silca gel. [d] Oil Level Gauge. [e] Oil Filter Valve. [f] Oil Drain Valve.[g] Therometer Pocket. [h] Diagram and rating plate. |
| 32 | Sl. Item No.29 (Contd…)[j] Two Earthing arrangements. [k] Lifting lugs. [l] Cooling Radiators. [m] Air Vent Plug. [n] Explosion Vent. [o] Cable Box ON H.V Side [p] Cable Box ON L.V Side. [q] Additional Netural Terminal Brought Outside Earthing. |
| 33 | S & F switch air break, Gang operated, outdoor type, mechanically operated,Vertical, mounted on 9 Nos of insulator and steel frame, with operating mechanism worked from ground level, complete with locking arrangements including pad locks with key of make Godrej / harrison, for current rating 400 Amps, 33kV and insulators suitable for 33 kV Grade, 50 Hz including GI Pipe, Medium Grade and all other materials complete all as specified and directed. |
| 34 | M & L HT Disc insulator, 33KV, porcelain, vitreous 145mm high and 255mm dia ball and socket type, white, brown or green complete all as specified and directed. |
| 35 | M & L for precast RCC cable route indicator duly engraved with letters with HT/LT/ UG Cable of size 600mm x 600mm, 100mm thick with semi circular shaped top made of RCC 1:2:4, using 20mm graded stone aggregate, duly reinforced with high strength corrosion resistant deformed TMT bars of grade Fe-500D of 10 dia, duly grouted up to 300mm using PCC 1:3:6, Type C1 complete including necessary excavation and earth work and applying two coats of weather proof exterior emulsion paint (100% acrylic) over a coat of weather proof exterior primer of same manufacturer as that of paint on all the exposed concrete surface complete all as specified and directed. |
| 36 | Supply and fixing LT Junction box for street light sheet molding compound (SMC), hinged door type and locking arrangement , off white colour of size 130mm x 180mm x 77mm (Make-sintex) comprising of Aluminium busbar of adequate capacity and 6A SP MCB-01 No backlite base netural link and 01 nos earthing terminal bolt and nut and connecting up with 2 runs of PVC sheathed cable, multistrand of size 2.5 sqmm complete all as specified and directed. |
| 37 | S&F LED aviation obstruction light 240 Volt comprising of die cast aluminium alloy housing, clear glass with built in power supply unit including cables & timer power etc all as specified and directed. Make: Bajaj BGAv 302 LED or Equivalent |
| 38 | Supply and fix sheet metal enclosure of timelite distribution board of 32A 3 pole/230V with astronomical time switch complete all as specified and directed. Make: IndoAsian Cat ref TDA-45163 of equivalent make. Please Enable Macros to View BoQ information |
