|
| 1 | Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 meters lead : Of area of 3 sqm. and below |
| 2 | Demolishing cement concrete manually/by mechanical means including disposal of material within 50 meters lead as per direction of Engineer-in charge: 15.2.1 1:3:6 or richer mix (i/c equivalent design mix) |
| 3 | Dismantling old plaster or skirting, raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 meters lead. |
| 4 | 12mm Cement plaster of mix:13.1.1 1 : 4 ( 1 cement : 4 fine sand) |
| 5 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 40 mm nominal size) |
| 6 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) |
| 7 | Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) after surface preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound@ 0.253 kg/sqm. (b) laying second layer of Fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm. (c) third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/sqm mixed with water proofing cement compound @ 0.670 kg./sqm. and coarse sand @1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30cm on parapet wall and tucked into groove in parapet all around. (d) fourth and final layer of brick tiling with cement mortar (which will be paid for separately) For the purpose of measurement the entire treated surface will be measured. |
| 8 | \\"Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. With ISI marked M.S. pressed butt hinges bright finished of required size with necessary screw 35 mm \\" |
| 9 | \\"Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. With ISI marked M.S. pressed butt hinges bright finished of required size with necessary screw 30 mm \\" |
| 10 | Providing and fixing aluminium work in doors, windows, ventilators, partitions with standard tubular section with dash fastener of required dia and shape and size jointed mechanically including ACP sheet/5mm thick /plain glass/ frosted glass/ laminated board panel complete with hardware fittings, powder coated aluminium, minimum thickness of powder coated 50 micron and conforming to IS 733 & IS 1285 (16 guage) complete job. |
| 11 | Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 meters lead : Of area of 3 sqm. and below |
| 12 | providing and fixing 4mm thick straight line teak ply including cutting ,wastage,fevicol,nails,carriage etc.complete (green,century,archid) |
| 13 | Providing and fixing of 19mm thick ply including cutting, wastage, fevicol, nails, carriage etc. complete item of superior make (green, century, amulya , orchid) conforming BWP 710...... |
| 14 | Providing and fixing of 1mm thick summica including cutting, wastage, fevicols nails etc. complete (green, amulya, virgo) |
| 15 | wooden polish on doors ( fiiling voids with chalk mitti,smooth with sand paper & Including material complete job ) |
| 16 | providing &fixing of ply 6mm thick ply including cutting wasteage fevicol carriage etc complete item of superior make ( green,century,amulya archid ) conforming BWP 710 |
| 17 | Providing and fixing ISI: 12817 marked Stainless Steel Butt Hinges with Stainless Steel screws etc. complete. 100x58x1.90 mm |
| 18 | Providing and fixing ISI: 12817 marked Stainless Steel Butt Hinges with Stainless Steel screws etc. complete. 75x47x1.80 mm |
| 19 | Providing and fixing ISI marked oxidized M.S. handles conforming to IS : 4992 with necessary screws etc. complete : 100 mm |
| 20 | Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete. |
| 21 | Providing and fixing of door closer to Aluminium doors by way of drilling screws etc. complete (ISI make) of standard make |
| 22 | Providing and fixing ISI marked M.S. pressed butt hinges bright finished with necessary screws etc. complete : 100x58x1.90 mm |
| 23 | Providing and fixing ISI marked oxidized M.S. sliding door bolts with nuts and screws etc. complete : 300x16 mm |
| 24 | providing and fixing of stainless steel tower bolt 100 mm Heavy duty |
| 25 | providing and fixing of stainless steel tower bolt 150 mm Heavy duty |
| 26 | providing and fixing of stainless steel door handles 100mm of heavy duty of approved make with necessery fitting and fixture complete |
| 27 | providing and fixing of stainless steel door handles 150mm of heavy duty of approved make with necessery fitting and fixture complete |
| 28 | providing and fixing of stainless steel heavy duty door lock of approved make complete with all neceesary fitting and fixtures |
| 29 | providing and fixing of stainless steel heavy duty dummy door lock of approved make complete with all neceesary fitting and fixtures |
| 30 | Providing and fixing chromium plated brass curtain rod having wall thickness of 1.25mm with two chromium plated brass brackets fixed with C.P. brass screws and PVC sleeves etc., wherever necessary complete :25 mm dia |
| 31 | Renewing glass panes, with putty and nails wherever necessary including raking out old putty : Float glass panes of thickness 4.0 mm(weight not less than 10kg/sqm) |
| 32 | \\"Providing and fixing of UV shhets ( light weight , highly durable &standard make )for wall panels etc.including design with stips , cutting ,fixing ,wastage ,carriage ..complete job . \\" |
| 33 | \\"\\"\\"UPVC Window Three track three panels sliding window made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead /double glazing bead of appropirate dimension (Area of window above 1.75 sqm) \\"\\" \\" |
| 34 | \\"Providing and fixing factory made uPVC white colour fixed glazed windows/ventilators comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately). Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. 9.149B.1 Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area upto 0.75 sqm.) \\" |
| 35 | \\"Providing and fixing glazing in aluminum door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer in-charge. (Cost of aluminum snap beading shall be paid in basic item.) With floating glass panes of 4.0 With float glass panes of 5.0 mm thickness (weight not less than 12.50 kg / sqm) \\" |
| 36 | Providing and fixing of 5 to 6mm thick super heavy PVC wall panelling with PVC angles/ corners including all accessories/arrangement including cutting wasttage ... |
| 37 | \\"Providing and fixing of 24 mm thick heavy quality wpc louvers of required design ,colour and pattern of standard make including cpmer profile ,fixture,carriage ,cutting wastage ,taxes etc. complete \\" |
| 38 | Providing and fixing of 8mm thick high density fibre board of EI Standard, highly resistant surface impregnated with melamine resin UV resistant /level-6, four side V-groove abrassion class AC4/class 32, plank size 1218x148x8mm including frame work of 25x12mm thick water proof ply batten and teak wood margin on top edge including carriage, wastage, loading, unloading etc. complete |
| 39 | Providing and fixing of wall paper with fevicol or equivalent adhesive including cleaning of wall surface, cutting wastage etc. complete item of superior make (as per directions of engineer incharge |
| 40 | Providing and fixing of 12.50 thick gypsum board wall tile of size 600x600 mm fully perforated as per approved design and drawing approparetly design powder coated G I T channel grid system as per instruction mannual of manufacture including cost of 50 mm thick internal / rock wood lining for accostics |
| 41 | Providing and fixing of Gypsumboard tile false ceiling sheets (9mm thick) 2'x2' as per pattern/design with G.I Channel frame work by way of drilling, fasteners screws, cutting wastage loading, unloading carriage etc. complete (boral or euivalent make) 6-8mm thick |
| 42 | Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping and sand papering and preparing the surface smooth Including necessary repairs to scratches etc. complete. |
| 43 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade, one or more coats on old work. |
| 44 | .Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately):2nd class D- wood |
| 45 | \\"Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting , hoisting , fixing in position and applying a primin coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes 6.4 kg/m |
| 46 | \\"Providing and fixing wire gauze shutters using galvanized M.S. wire gauze of average width for aperture 1.4 mm in both directions with wire of dia. 0.63 mm for doors, windows and clerestory windows with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws as per direction of Engineer-in-charge : |
| 47 | Providing & laying damp-proof Course 40 mm thick with cement concrete 1:2:4 (1 cement:2 coarse sand: 4 graded stone agg 12.5 mm nominal size) and curing complete |
| 48 | Providing and applying white cement based putty of specified thickness, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete 1 mm thick |
| 49 | Providing and applying white cement based putty of specified thickness, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete 2 mm thick |
| 50 | Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound) content. With ready mixed pink or grey primer on wood work (hard and soft wood) having VOC content less than 50 grams/ liter |
| 51 | Wall Painting with acrylic emulsion paint of approved brand and manufacture to give an even shade. Two or more coats on new work |
| 52 | Marble work gang saw cut (polished and machine cut) of thickness 16 mm for wall lining (veneer work), backing filled with a grout of 12 mm thick average in cement mortar 1:3 (1 cement: 3 coarse sand), including pointing with white cement mortar 1:2 (1 white cement: 2 marble dust) with an admixture of pigment to match the marble shade (To be secured to the backing by means of cramps, which shall be paid for separately). (Area of slab upto 0.5 sqm) |
| 53 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. completeSize of tile 600x600 mm (Khajaria, Somany or equivalent |
| 54 | 8.31.Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shadesexcept burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. (Khajaria, Somany or equivalent )\\" |
| 55 | Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, laid on 20 mm thick cement mortar 1:4 (1Cement : 4 Coarse sand), including grouting the joints with white cement and matching pigments etc., complete.In all colours, shades, except White, Ivory, Fume Red Brown |
| 56 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply, including all CPVC plain and brass threaded fittings. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer-in-charge: internal work concealed fixing the pipe with clamps at 1.00 m spacing including cutting chases and making good the wall etc. 20mm nominal outer dia pipes |
| 57 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply, including all CPVC plain and brass threaded fittings. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer-in-charge: internal work concealed fixing the pipe with clamps at 1.00 m spacing including cutting chases and making good the wall etc. 25mm nominal outer dia pipes |
| 58 | \\"Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply, including all CPVC plain and brass threaded fittings. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer-in-charge: internal work concealed fixing the pipe with clamps at 1.00 m spacing including cutting chases and making good the wall etc. 32mm nominal outer dia pipes \\" |
| 59 | Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 liter low level white P.V.C. flushing cistern, including flush pipe with manually controlled device (handle lever), conforming to IS:7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: W.C. pan with ISI marked white solid plastic seat and lid. |
| 60 | \\"Providing and fixing one piece construction white vitreous china squatting plate with an integral longitudinal flushing pipe, white P.V.C automatic flushing cistern, with fittings, standard size G.I./ PVC flush pipe for back and front flush with standard spreader pipes with fittings, G.I clamps and in C.P brass coupling complete, including painting of fittings and cutting and making good the walls and floors etc. wherever required: Range of three squatting plates with 10 liter P.V.C. automatic flushing cistern. \\" |
| 61 | \\"Providing and fixing wash basin with C.I. brackets, 15mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, includingpainting of fittings and brackets, cutting and making good the walls wherever required: White Vitreous China Flat back wash basin size 450x300 mm with single 15 mm C.P. brass pillar tap\\" |
| 62 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per I.S. 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :Kitchen sink without drain board470x420mm bowl depth 178mm |
| 63 | Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings. |
| 64 | Providing and fixing CP angle valve heavy (standard make) |
| 65 | provinding and fixing of cp long nose bibcock heavy ( standard make ) |
| 66 | provinding and fixing of cp short body bibcock heavy ( standard make ) |
| 67 | providing and fixing of CP greating 100 mm dia standard make |
| 68 | providing and fixing of hand jet for flushing standard make |
| 69 | Providing and fixing of spreader for urinal standard make 15mm dia |
| 70 | providing and fixing of waste coupling standard make (wash basin) |
| 71 | Providing and fixing of cp pillar cock heavy standard make |
| 72 | providng and fixing of cp mixer for wash basin heavy standard make |
| 73 | providing and fixing of pvc pipe dia 4\\" dia for ( rain water,drainage etc ) |
| 74 | providing and fixing of pvc pipe dia 3\\" dia for ( rain water,drainage etc ) |
| 75 | providing and fixing of pvc pipe dia 2\\" dia for ( rain water,drainage etc ) |
| 76 | providing and fixing of towel rod heavy standard make |
| 77 | providing and fixing of towel ring heavy standard make |
| 78 | providing and fixing of paper holder heavy standard make |
| 79 | providing and fixing of waste pipe flexible heavy standard make |
| 80 | providing and fixing of soap case heavy standard make |
| 81 | providing and fixing of pvc conection heavy standard make 45cm |
| 82 | providing and fixing of pvc conection heavy standard make 60cm |
| 83 | provinding and fixing of pvc flush cistern 10 liter capacity standard make |
| 84 | Engaging skilled for specilised job during execution of work at site |
| 85 | shifting of debries / cleaning site /other allied works at site by engaging skilled and unskilled labours ,unskilled |
| 86 | Engaging trolley for shifting of mulba from site to beyond the municipality limit incl. Loading and unloading complete job Please Enable Macros to View BoQ information |
