|
| 1 | Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. complete all as specified and directed. |
| 2 | Dismantling of stone slabs and tiles (Kota stone etc.) of any description or any thickness in floors, aprons, skirting, dado etc. laid bedded and pointed in any mortar complete all as specified and directed. |
| 3 | M&L for light shade Virified Ceramic tiles 7 to 8mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, including screed bed 15mm thick in CM 1:6 complete all as specified and directed. |
| 4 | M&L for light shade Virified Ceramic tiles 7 to 8mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm in vertical surfaces includig 10 mm thick rendering in CM 1:3 complete all as specified & directed. |
| 5 | M&L for 18-20mm thick Granite (of any type) (Jet black) work (table rubbed and polished) in cooking platform, Jambs cill and like set in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match shade of granite including rounding of exposed edges of slab smoothly and polished complete all as specified and directed. |
| 6 | M&L for machine cut Kota stone slab 20 mm to 25 mm thick, as in slab/shelves/plateform and thread for steps set and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing to give granite finish, complete all as specified and directed. |
| 7 | Demolition of precast concrete block walling and similar items i.e.. ashlar facing dressed stone work, precast concrete articles etc., of any description and in any position, built in cement mortar, including all quoins, arches and pillars etc. complete all as specified and directed. |
| 8 | M&L for precast cement concrete block masonry with solid blocks of PCC (1:3:6) type C-1 (using 20mm and 12.5 mm graded stone aggregate in the proportion as directed) exc 10cm in width and set and jointed in Cement Mortar (1:6) complete all as specified and directed. |
| 9 | Demolition of cement concrete of any description and in any position (reinforced) in slab etc complete all as specified and directed. |
| 10 | M& L for Precast RCC 1:1-1/2:3 type B1 (using 20mm graded stone aggregate) supported on walls and the similar works complete all as specified and directed by Engr In charge Complete |
| 11 | M&L for Reinforcement 8 to 10mm dia TMT bars cut to length, bent to shape required and binding with MS wire not less than 0.9mm dia in stirrups complete all as specified and as directed. |
| 12 | Taking down carefully Cement Concrete (Reinforced) in chajjas ,staircase,landing,window sunshades and other suspended portion at any height, including cutting down of damaged or rusted reinforcements and making the surface good by rendering 10-15 mm thick of CM 1:3 or cement concrete 1:2:4 on exposed concrete and finishing the surface even and smooth including necessary formworks complete all as specified and directed. |
| 13 | Taking down carefully cement concrete/ spalled out concrete from RCC roof projections,Ceilings,Sunshades,beams etc upto cover depth by chipping out lightly including necessary scaffolding etc complete all as specified & directed. |
| 14 | M&L for cleaning the existing reinf of slabs chajjas etc & applying a coat of SIKA RUSTOFF 11 or equivalent of pidilite,fosroc,Thermax etc to remove rust particles etc throughly cleaning the surface complete all as specified & directed. |
| 15 | M&L for applying a coat of bond coat made with cement slurry(1part cement to 1.5-2parts water) mixed with admixture LATEX POWER mixed @5 Kg per 50kg of cement & applying to the concrete surfaces @200gm/sqm to obtain tackcomplete all as specified & directed. |
| 16 | M&L for 15-20mm thick rendering in CM 1:1:2 using 1 part cement to 1part 2-3mm screenings of stone agg & 2 parts coarse sand over the bond coat applied surfeces with cement mixed SIKA PLASTOCRETE admixture equivalent of pidilite,fosroc,Thermax etc @100gm/50kg of cement & finishing the surfaces even & rough to recieve final rendering coat complete all as specified & directed. |
| 17 | M&L for 10-15mm thick rendering in CM 1:3 over the bond coat applied surfeces with cement mixed SIKA PLASTOCRETE SUPER admixture @100gm/50kg of cement & finishing the surfaces even & smooth complete all as directed at site complete all as specified & directed. |
| 18 | S&F GI chicken wire mesh of 0.71mm dia wire & 12mm mesh size fixed with nails & screws around RCC chajjas/fascias etc complete all as specified & directed. |
| 19 | Taking down cement plaster of any description and in any position of brick/concrete surfaces on walls/celling etc. including racking out joints, hacking for key, scrubbing down with water etc & prepared to receive new plaster complete all as specified and directed. |
| 20 | M&L for 15 mm thick rendering in cement mortar on fair faces of brick work or concrete surfaces , applied in two layers i.e.. Ist layer of 10 mm thick rendering in cement mortar (1:6 ) and 2nd ( top ) layer of 5 mm thick rendering in cement mortar (1:4 ) complete all as specified and directed. |
| 21 | M&L for rendering 15 mm thick in CM (1:6) on fair faces of brick work or concrete surfaces/stone masonry and finishing the surfaces even and smooth without using extra cement complete all as specified and directed. |
| 22 | M&L for rendering 5 mm thick in Cement Mortar (1:3) on ceiling finished even and smooth without using extra cement complete all as specified and directed. |
| 23 | Material & Labour for preparation of old/new wall surfaces and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm complete all as specified and directed. |
| 24 | M&L for preparation of old/new plastered surfaces of wall and applying 2 coats of Oil Bound distemper over 1.5mm to 2mm thick wall putty finished to a even and smooth finish over a coat of alkali primer complete all as specifed directed. |
| 25 | M&L for preparation of the newly plastered surfaces of ceiling & applying 3 coats of white wash on ceiling surfaces complete all as specified and directed. |
| 26 | M&L for preparation of old decorated surface of wall and including cornices plastered or unplastered surfaces by brooming down or steel wire brushing to remove all loose scales, and foreign materials scarping down , smoke soot moulds , moss and efflorescent salts treating oil and greasy spots and M&L applying one coat of white wash , complete all as specified and directed. |
| 27 | M&L for preparation of old decorated surface of ceiling and including cornices plastered or unplastered surfaces by brooming down or steel wire brushing to remove all loose scales, and foreign materials scarping down , smoke soot moulds , moss and efflorescent salts treating oil and greasy spots and applying one coat of white wash complete all as specified and directed. |
| 28 | M&L for preparation of new steel surfaces exc 10 cm width or girth and applying two coat synthetic enamel paints on new steel surfaces over a coat of red oxide zinc chrome primer complete all as specified and directed. |
| 29 | M & L applying two coats of synthetic enamel paint on old wooden surfaces of any description over 10 cm width or girth over including preparation of surfaces complete all as specified & directed. |
| 30 | M&L for water proofing treatment to wall surfaces as under :-Surface PreparationSurface must be thoroughly cleaned, free of dust, grease etc and washed well with water. The surface to be checked for cracks, hollowness and loose plastered areas etc if any. All loose plaster and cracks larger than 10 mm width to be repaired with polymer modified mortar using Dr. Fixit Pidicrete URP. The cracks up to 5 mm to be treated with Dr. Fixit Crack-X Paste and the larger ones up to 10 mm with Dr. Fixit Crack-X Shrinkfree.PrimingAfter the proper surface preparation and curing of repaired areas wash the surface well and maintaining it in saturated surface dry condition proceed for priming using Dr. Fixit Primeseal diluted in 2:1 ratio with water (2 parts Primeseal diluted with 1 part water). Maintain the spreading rate of 8-10 sq mtr per litre for a single coat application to achieve about 20 – 25 microns DFT. Allow it to dry for 6-8 hrs.COATINGBrush apply one coats of Dr. Fixit Raincoat Waterproof Coating without any dilution Maintain the spreading rate of 3.5-4.0 sq mtr per litre / coat application to achieve about 120-130 microns DFT. The second coat of Dr. Fixit Raincoat Classic Topcoat to be apply with interval of 6-8 hours without any dilution. Maintain the spreading rate of 7-8 sq mtr per litre / coat application to achieve about 50-60 microns DFT. |
| 31 | Demolition of cement concrete of any description and in any position (unreinforced) in ground floors/ paving not exceeding 15 cm thick (below or above GL) complete all as specified and directed. |
| 32 | M&L for 40 mm thick PCC 1:2:4 type B-1, (20mm graded stone aggregate) as in sub floor, sub bases, floor and paving etc; complete all as specified. |
| 33 | M&L for PCC (1:3:6) type C2, (using 40mm graded stone aggregate) as in plinth protection, 75 mm thick, finishing the surface even and smooth w/o using extra cement including forming expansion joints 65 mm deep x 10 mm wide complete all as specified and directed. |
| 34 | Supply and fixing in repairs decorative type curtain rod stainless steel finish of pipe 22 to 25 mm dia as per sample approved by GE complete all as specified & directed. |
| 35 | Supply and fixing of purpose made brackets trade pattern for decorative type curtain rods suitable for holding 22 to 25 mm dia as per sample approved by GE complete all as specified & directed. |
| 36 | Supply and fixing in repair of decorative fincals (round type with mirror optic finish) trade pattern for decorative type curtain rods suitable for 22 to 25 mm dia curtain rods as per sample approved by GE's complete all as specified & directed. |
| 37 | Taking down chowkat or frames n.exc 1.5 sqm with shutters without taking off shutters from the frame and removing to store complete all as specified and directed. |
| 38 | Taking down chowkat or frames exc 1.5 sqm & n exc 4 sqm with shutters without taking off shutters from the frame and removing to store complete all as specified and directed. |
| 39 | S & F Powder coated Aluminium alloy sections sliding windows with frames Series-C (20mm) and , 3 track sliding shutters duly fitted with neoprene beading, glazing clips, shutters with tinted glass 5mm thick and stainless steel wire cloth 0.36mm dia and average width of aperture 1.4mm , aluminium alloy handles etc. complete all as specified and directed. |
| 40 | M & L powder coatedaluminium deco grill medium grade of mesh size 75mmx75mm with 6mm square anodised aluminium bars fixed with aluminium frame of size 9x9x1 mm complete all as specified and directed. |
| 41 | S & F for anodised Aluminium partition/ door frame of size 100 x44 x 1.98mm thick with one or more rebates and shutters pull and push type or side hung type (with or without aluminium sash bars) comprising of top & lock rails of section 115 x 44 x 1.98mm thick, bottom rail of section 150 x 44 x 1.98mm thick and stiles of section 85 x 44 x1.98mm thick including necessary jointing cleat, glazing clip, rubber packing anodized aluminium beading, screws, anodized aluminium fittings such as floor spring or hinges 100mm size with hydrolic door closer, handles 'D' type 125mm, floor door stopper, tower bolts 200mm, sliding door bolt 300mm or mortice lock with 5mm thick tinted glass /pre laminted particle board (Novapan) panel and making good to the disturbed wall surfaces to match existing surface complete all as specified and directed. |
| 42 | S&F factory made solid panel PVC door shutter 30mm thick (Style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded Single Side Prelam PVC sheet used instead of Plain colour PVC sheet and stile & rails having one side feathered edge and on other side 10mm 90 degree bent edge PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and single side prelam PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail ; panelling of prelam colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading & jointed together with solvent cement, supply & fixing in the frame at site as per SSR specifications & diagram/product drawing shown on sl page NO 146 of SSR Part II with the size of door shutter as required complete all as specid & directed. |
| 43 | S&F solid PVC door frame of size 50mmX47mm made out of 5mm one side prelam colour PVC sheet reinforced with MS square tube all as per specifications and as per drawing complete all as specified and directed. |
| 44 | S&F 30 mm thick factory made Flush shutters , solid core construction , with block board core and plywood face panels commenrcial face on bath sides with lipping/frame to match complete all as specified and directed. |
| 45 | M & L for 30 mm thick glazed and skeleton shutters of 2nd class Hard Wood(Not less than Hollock wood) local made shutter, open rebated and prepare to revive glass, gauge etc (without sash bars ) edges of framing plain chamfered or rounded, fitted with moulded beads both sides for securing glass etc, size of members of shutters as specified in SSR part I section 8 clause 8.24 (a) supplied and fitted to chowkat complete all as specified and directed. |
| 46 | S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified & directed. |
| 47 | S&F for butt hinges 100mm size medium weight stainless steel complete all as specified and directed. |
| 48 | M&L for 150mm long extructed aluminium handle fabricated type complete all as specified and directed. |
| 49 | S&F Aluminium anodised barrel tower bolt of extruded section 200 mm size complete all as specified and directed. |
| 50 | S&F Aluminium alloy, anodised, sliding door bolt 200mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed. |
| 51 | S&F Aluminium alloy, anodised, sliding door bolt 300mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed. |
| 52 | S&F in repair 5mm thick, 600mm wide rounded edge mirror of selected quality glass, with back polishig mounted and fixed with stainless steel decorative cap wahsers and screws set fixed on PVC rawl plugs complete all as specified and directed. |
| 53 | S&F Framed work as in doors,gates or staging to water tank of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and directed Fe 410-W (Gde- E- 250) quality- A complete all as specified & directed. |
| 54 | Taking down carefully copper/alumunium point wiring for light, fan, bell, socket or power complete including fittings such as switches, ceiling roses pendents regulators, sockets and tube light fittings etc, removing materials from site or for reuse refixing and making good distrubed surface of wall, floors etc all as specified and directed. |
| 55 | Taking down main switches from DBs with sheet metal enclosure 08/04 way SPN/TPN DBs etc all as specified and directed. Please Enable Macros to View BoQ information |
| 56 | Taking down main switches from DBs with sheet metal enclosure 08/04 way SPN/TPN DBs etc all as specified and directed. Please Enable Macros to View BoQ information |
