|
| 1 | Demolition of old roof treatment of any type and thickness and pattern and dismantling of old brick tiles preparation of RCC roof surfaces with wire brushes to remove the old treatment, foreing material loose particles etc complete all as specified and as directed. |
| 2 | M&L for 40mm thick (avg) thickness cement concrete 1:2:4 type B0 (using 12.5 mm graded stone aggregate) as in padding finishing the surface even and smooth without using extra cement complete all as specified and as directed. |
| 3 | M&L for bitumen felt water proofing treatment using APP based polymeric membrane minimum weighting 3 kg/sqm and minimum thickness 3mm reinforced with polyster non wove fabric (but not less than 150gms/sqm) laid over bitumen primer applied @ 0.30 Kg/sqm by forced application complete all as specified and as directed. |
| 4 | M&L for cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified and as directed. |
| 5 | M&L for providing cement concrete type B0 1:2:4 (using 12.5mm graded stone aggregate) as in roof kerbs or mud stops, rounded or chamfered on edges complete all as specified and as directed. |
| 6 | M&L for cement concrete tiles 25cm x 25cm x 22mm thick, with grey cement and no pigments, machine pressed, set in neat cement slurry in floor over and including 15 mm thick screed bed in cement mortar 1:4 and filling the joints with Tile Max premium cementations’ grout material complete all as specified and as directed. |
| 7 | Dismantling wall and ceiling boards (fiber, pulp, insulation, etc) or insulation board/slabs/ blankets, any thickness, including cover fillets complete all as specified and as directed. |
| 8 | S&F for Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing complete all as specified and as directed. |
| 9 | S&F for 5mm thick PVC sheet fillet of width 35mm for wall panelling inclusive of fixing on to wall to make PVC Frame as per specification and drawing complete all as specified and as directed. |
| 10 | M&L for providing and fixing false ceiling with semi perforated 12 mm thick micro regular edged GRG false ceiling tiles at all heights with GRG (Glass fibre reinforced Gypsum) False ceiling tiles of size 595x595mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%,NRCO .50 to 0.75 as per IS 8225:1987, Non combustible as per BS 476 (part-4)-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on interlocking metal T-Grid of hot dipped galvanized iron section of 0.33 mm thick (galvanized @120 grams per sqm (including both sides) comprising of main T runners of size 15x32mm of length 3000mm ,cross T of size 15x32 mm of length 1200 mm and secondary intermediate cross T of size 15x32 mm of length 600mm to form a grid module of size 600x600mm,suspended from ceiling using galvanized mild steel items (galvanizing @ 80 grams per sqm) i.e. 50 mm long ,8mm outer diameter M-6dash fasteners ,6mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85x25x2mm. Galvanized iron perimeter wall angle of size 24x24x0.40 mm of length 3000mm to be fixed on periphery wall /partition with the help of plastic rawl plugs at 450 mm center to center and 40 mm long dry wall screws. The work shall be carried out as per specifications, drawing and as per directions of Engineer-in-Charge. |
| 11 | Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed. |
| 12 | M&L for coloured Non skid Ceramic tiles 7 to 8mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15mm thick screed bed in cement and sand mortar 1:6 complete all as specified and directed. |
| 13 | M&L for coloured Glazed ceramic tiles on vertical surface 600x300x7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match fixed over and including 10 mm thick backing coat of cement mortar in 1:4 complete all as specified and directed. |
| 14 | M&L for coloured double charged Vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exc 1.00 Sqm as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15 mm thick screed bed in cement and sand mortar 1:6 complete all as specified and as directed. |
| 15 | Taking down cement or cement lime plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and as directed. |
| 16 | M&L for rendering 15 mm thick on brick wall or concrete surface in cement and sand mortar 1:4 finished even & fair complete all as specified and as directed. |
| 17 | Supply only liquid water Proofing Compound complete all as specified and as directed. |
| 18 | M&L for providing damp proof layer in two coats of acrylic polymer coating consisting of 1 part of acrylic polymer liquid mixed with 2 parts of cementations powder applying at the rate of 1.40 Sqm/Kg of mix per coat. Second coat should be applied after 4-6 hrs of first coat, 5 days curing is to be carried out to the surface before providing plastering complete all as specified and as directed. |
| 19 | M&L for preparation of newly plastered surfaces of walls and applying two coats of Exterior Emulsion paint over a coat of primer complete all as specified and as directed. |
| 20 | M&L for rendering 15 mm thick on other than fair faces brick wall or concrete surface in cement mortar 1:6 finished even & smooth without using extra cement complete all as specified and as directed. |
| 21 | M&L for preparation of newly plastered surfaces of walls and applying two coats of oil bound distemper over a coat of Alkali resistant primer complete all as specified and as directed. |
| 22 | M&L for providing one coat of wall care putty complete all as specified and directed. |
| 23 | M&L for applying antirust compound over exposed steel surfaces and providing dubbing coat over chicken wire mesh in cement and sand mortar 1:1 complete all as specified and directed. |
| 24 | M&L for providing ready mix plaster over exposed steel surfaces after treatment by antirust compound /chemical of exposed steel surfaces complete all as specified and directed. |
| 25 | M&L for 10mm thick rendering on fair faces of brick/concrete surface as in ceiling in cement mortar 1:3 finished the surface even and smooth without using extra cement complete all as specified and as directed. |
| 26 | M&L for preparation of new plastered surface of ceiling and applying three coats of white wash on ceiling surface complete all as specified and as directed. |
| 27 | Demolition of brick work or stone boulder masonry built in cement mortar including all quoins arches pillars etc. but excluding ashlars facing dressed stone work and precast concrete articles complete all as specified and as directed. |
| 28 | M&L for Brick work with modular sub class B bricks straight or curved on plan exc 6 m mean radius built in cement and sand mortar 1:6 complete all as specified and directed. |
| 29 | M&L for Brick work with modular sub class 'B' brick straight or curved on plan to any radius in half brick thick walls built in cement and sand mortar 1:4 complete all as specified and as directed. |
| 30 | Demolition of reinforced concrete (cutting reinforcement as required to facilitate demolition of roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work complete all as specified. |
| 31 | S&F MS Joist, channel, angle, or tee sections, fixed independently, without connection plate, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) complete all as specified. |
| 32 | M&L for 50mm thick sand stone slab set and jointed over supports as in chajjas of ground and first floor's over windows, doors etc and jointed in cement mortar 1:4 complete all as specified and as directed. |
| 33 | Use & waste of Form work to soffits of suspended slabs such as roof slabs floor slab landing and similar work for not exceeding 200mm thick (horizontal or sloping) for rough finished surface of concrete complete all as specified and as directed. |
| 34 | M&L for reinforced cement concrete Type B1 1:2:4 using 20 mm graded stone aggregate as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed. |
| 35 | M&L for steel reinforcement of TMT bars (FE-500 Grade) 10 mm dia and over cut to length and bent to shape required including cranking bending spirally for hooping for columns hooking end and binding with and including mild steel wire ( annealed ) not less than 0.9mm dia or securing with clips complete all as specified and as directed. |
| 36 | M&L for 25mm average thick PCC 1:2:4 type B0 (using 12.5 mm grade stone aggregate) in floors/padding finishing the surface even and smooth without using extra cement complete all as specified and as directed. |
| 37 | Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth of brick walls complete all as specified and as directed. |
| 38 | M&L for galvanized steel water tubing medium grade (ISI marked) of 15mm bore with & including all fittings, fixed to walls and ceilings or laid in floors, including taking up or down existing unserviceable steel water tubing and connections of 15mm bore complete all as specified and as directed. |
| 39 | M&L for galvanized steel water tubing medium grade (ISI marked) of 20mm bore with & including all fittings, fixed to walls and ceilings or laid in floors, including taking up or down existing unserviceable steel water tubing and connections of 20mm bore complete all as specified and as directed. |
| 40 | M&L for galvanized steel water tubing medium grade (ISI marked) of 25mm bore with & including all fittings, fixed to walls and ceilings or laid in floors, including taking up or down existing unserviceable steel water tubing and connections of 25mm bore complete all as specified and as directed. |
| 41 | Demolition of Stone slabs and tiles of any description or thickness (except ceramic tiles) in floors, aprons etc. laid, bedded and pointed in any mortar complete all as specified and directed. |
| 42 | M&L for 16-18mm thick Granite slab work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like laid over and including 20mm thick screed bed in cement mortar 1:4 and pointing in white cement (1:2 )using marble dust with admixture of pigment to match with shade of granite, including rounded/half rounded edge and providing hole for gas pipe in pre-cast slab as well as in granite slab of cooking platform complete all as specified and as directed. |
| 43 | M&L for complete removal of existing treatment of old surfaces on wall surfaces and applying two coat of oil bound distemper over one coat of wall care putty complete all as specified and directed. |
| 44 | M&L for preparation of old plastered surface of ceiling and applying two coats of white wash all as specified and directed by engineer in charge. |
| 45 | S&F in repair 110 mm bore PVC (SWR) Class 'B' pipes single socket, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed. |
| 46 | S&F in repair 75 mm bore PVC (SWR) Class 'B' pipes single socket, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed. |
| 47 | S&F in repair 110 mm bore PVC (SWR) Class 'A' pipes single socket, in any length with rubber ring joints, fixed to walls complete all as specified and as directed. |
| 48 | S&F in repair 75 mm bore PVC (SWR) Class 'A; pipes single socket in any length with rubber ring joints fixed to walls complete all as specified and as directed. |
| 49 | S&F in repair 110 mm bore PVC (SWR) plain bends any radius complete all as specified and as directed. |
| 50 | S&F in repair 75 mm bore PVC (SWR) bends any radius complete all as specified and as directed. |
| 51 | S&F in repair 75 mm bore PVC (SWR) bends with access door any radius complete all as specified and as directed. |
| 52 | S&F in repair 110mm bore PVC (SWR) class 'B' junction (Single T) equal or unequal complete all as specified and as directed. |
| 53 | S&F in repair 110mm bore PVC (SWR) vent cowl complete all as specified and as specified. |
| 54 | S&F in repair PVC floor trap plain 75 mm dia of outlet with grating including jointing with solvent cement complete all as specified and as directed. |
| 55 | S&F 15mm bore long body bib taps cast copper alloy, chromium plated, fancy type with half turn handle having weight of bib tap should not be less than 450 gms or as per SSR Part-I specification for iron pipes complete all as specified and as directed.Make: Jaquar Cat Part No. KUP-CHR-35037/CERA Cat Part No. F-1003151/Kohler Cat Part No. K-160931N-4-CP |
| 56 | S&F in repair fancy type 15mm bore long body angular cock, cast copper alloy, chromium plated, fancy type with capstan head having weight of angular cock should not be less than 450 gms or as per SSR Part-I specification, screwed down, screwed both end for iron pipes complete all as specified and as directed.Make : Jaquar, Cat Part No. KUP-CHR-350553PM/Cera, Cat Part No. F-1014201/Kohler, Cat Part No. K-801541N-4AV-CP |
| 57 | S&F in repairs 15mm bore stop valve, chromium plated with long shank and cup (Concealed type) both ends for iron pipe complete all as specified and as directed. |
| 58 | S&F in repair vitreous china wash hand basin white flat back size 550 x 400 mm including bracket and pair of rack bolts waste coupling pillar tap cast copper alloy chromium plated fancy type complete all as specified and directed. |
| 59 | S&F in repair Single Lever Surgical purpose Elbow action Basin Mixer with extended operating Lever with 150 mm long Braided hoses complete all as specified and as directed. |
| 60 | S&F in repairs 15mm dia brass chromium plated pillar tap long shank with fly nuts capastan head screwed down high pressure with or without lettered hot or cold with long screwed shank having weight of pillar should not be less than 450 gms or as per SSR Part-I specification complete all as specified and as directed. |
| 61 | S&F in repairs 750 mm long PVC flexible waste pipe 32 mm dia for fixing in urinals and wash basin complete all as specified and as directed. |
| 62 | S&F in repair designer looking mirror of size not less than 1.0 Sqm, selected quality 5 mm thick, fixed with chromium plated screws complete all as specified and as directed. |
| 63 | S&F Swivel CP shower of size 200 mm for fixing with 15mm pipe (minimum weight 40gms) complete all as specified and as directed. |
| 64 | S&F Shower arm 15 mm size, 195mm long with bend of 45 degree with flange of PTMT any colour (minimum weight 40gms) complete all as specified and as directed. |
| 65 | S&F in repairs viterous china squatting pan, Órissa pattern, size 580 x 440mm white, with integral foot rests including connection and fitting to trap, and to flushing pipe complete and making good to wall or floor tilling to match the existing complete all as specified. |
| 66 | S&F in repairs white Vitreous china wash down water closet (pedestal pattern) with fixing bolt, Plastic water closet seat, white, closed pattern with flat bottom, and cover with aluminised hinging device, including all connection complete all as specified and as directed. |
| 67 | S&F in repair colour european type combination pattern WC casket type christinna with mounted flushing cistern, pvc connection, seat cover and jointed to sewage pipe complete all as specified and as directed. |
| 68 | S&F in repair Toilet Roll Holder fixing to wall complete all as specified and directed. |
| 69 | S&F in repair Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement complete all as specified. |
| 70 | S&F in repairs 10 litres PVC (White) valve less syphonic action type, flushing cistern low level with inlet ball valve float, handle, aluminium brackets for bottom support fixing with gitties embedded in wall with drilling machine etc complete. |
| 71 | S&F in repair 15 mm size two way angle cock cast copper alloy, chromium plated, fancy type with capstan head, screwed down, screwed for iron pipes complete all as specified and as directed. |
| 72 | S&F in repair Health faucet of superior quality ABS body with 8 mm dia 1.2 m long flexible tube and wall hook including fixing complete all as specified and as directed. |
| 73 | S&F in repair 600 mm long PVC connections 15 mm size with PTMT nuts at both end complete all as specified and as directed. |
| 74 | S&F in repairs stainless steel towel rail 600 mm long 20 mm dia fixed with steel screw etc complete all as specified. |
| 75 | S&F in repair stainless soap dish fixed to wall complete all as specified and directed. |
| 76 | S&F in repair Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and as directed. |
| 77 | S&F in repairs corner racks with glass of size 300x300mm, 8mm thick bevelled on edges with two brackets CP complete all as specified. |
| 78 | Supply and fixing in repair 500 litres capacity white colour triple layer, rotational moulded, polythene water storage tank (Cylindrical vertical with closed top) hoisted and fixed on roof in position, including all fitting such as connection pieces with GI tank nipple for inlet, outlet, washout and overflow etc and including Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe 20 mm bore dia complete all as specified and as directed. |
| 79 | Supply and fix in repair 1000 litres capacity white colour triple layer, rotational moulded, polythene water storage tank (Cylindrical vertical with closed top) hoisted and fixed on roof in position, including all fitting such as connection pieces with GI tank nipple for inlet, outlet, washout and overflow etc and including Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe 20 mm bore dia complete all as specified and as directed. |
| 80 | S&F in repair 20mm bore Gun metal, globe or gate valves, with iron wheel head, including making thread to both ends of pipes for fixing, screwed both ends for iron pipes and fixed complete all as specified and as directed. |
| 81 | S&F in repair stainless steel kitchen plate rack of size 31\\" x 30\\" x 10\\" deep, fabricated with 0.63 mm sheet fixed in position on wall complete all as specified and as directed. |
| 82 | S&F sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and as directed. |
| 83 | S&F sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and as directed. |
| 84 | S&F in Resecuring or easing & adjusting without taking down door shutter area not exc 1 sqm each complete all as specified and as directed. |
| 85 | S&F in Resecuring or easing & adjusting without taking down door shutter area exc. 1 Sqm but not exc 2 Sqm each complete all as specified and as directed. |
| 86 | Taking down chowkhats or frame with shutter (without taking off shutters from the frame) area not exc. 1.50 Sqm each and making good the disturbed surface complete all as specified. |
| 87 | Taking down chowkhats or frame with shutter (without taking off shutter from the frame) area exc 1.50 Sqm and n.exc 4.00 Sqm each and making good the disturbed surface complete all as specified. |
| 88 | Taking down shutters of any description exc 1.00 Sqm and not exc 2.00 Sqm each complete all as specified and as directed. |
| 89 | M&L for Pressed steel frames 105x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed complete all as specified and as directed. |
| 90 | M&L for Pressed steel frames 125x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed complete all as specified and as directed. |
| 91 | M&L for cement concrete type C-1 (1:3:6) 20mm graded stone aggregate as in bed blocks for fixing hold fasts and filling of chowkhats etc. complete all as specified. |
| 92 | S&F 35mm thick factory made Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkhats complete all as specified and as directed. |
| 93 | Supply & Fixing stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and as directed. |
| 94 | S&F 30mm thick flush door shutter, solid core construction with block board core and plywood face panels, commercial type on both sides complete all as specified and directed. |
| 95 | S&F Floor door stopper of aluminium anodised body and tengue, anodised with hard drwan steel spring overall length of cover plate 150 mm complete all as specified and as directed. |
| 96 | S&F in repair 300 mm size mild steel rat tail rod pattern door springs ISI marked including roller & roller plate etc complete all as specified and as directed. |
| 97 | S&F Solid Door Frame of size 50mm x 47mm for WPC door complete all as specified and as directed. |
| 98 | S&F 30mm thick factory made WPC door with both side lamination complete all as specified and as directed. |
| 99 | S&F Stainless steel handles of size 150 mm, fabricated type anodised complete all as specified and as directed. |
| 100 | S&F Stainless steel barrel tower bolts 200 mm length of bolt of extruded section and fixed complete all as specified and as directed. |
| 101 | S&F Stainless steel 250 mm sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of stainless steel and fixed complete all as specified and as directed. |
| 102 | S&F 100 mm long size of hinges, extruded aluminium alloy with galvanised mild steel hinges pin anodized and fixed type B-21 complete all as specified and as directed. |
| 103 | M&L for preparation of new steel surfaces of any description not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed. |
| 104 | M&L for preparation of new wooden surfaces of any description not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed. |
| 105 | S&F MS Framed work such as grills gratings, door and cooler stand, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars and similar work confirming to Fe.290.Gde-E-165 complete all as specified and as directed. |
| 106 | S&F providing and fixing factory made uPVC white colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm (+- 0.2mm). Window profile with hollow section with multi chamber, Frame (60mm x 62mm). sash (42mm x 67mm). Sliding Interlock (One vertical length in each shutters) (45.5mm x 28mm). Glazing bead (24.5mmx 16mm) will he mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc.. making arrangement for fixing of hardware. EPDM gasket 1.2 + -0.2mm thick galvanized steel frame (30mm x 21.5mm), Sash (30mm x 18mm), profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners. Hardware : [Touch Lock of zinc alloyed (white powder coated), steel roller system including 5mm thick glazing with selected quality glass, aluminum track on bottom rail for two track sliding frame, wool pine for Sliding sash and interlock complete all as specified and as directed.Note : The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net opening will be measured for payment purpose) Area not exceeding 2.00 sqm each |
| 107 | S&F Providing and fixing factory made uPVC white colour casement (Openable) Door made of extruded profile with wall thickness of 2.3mm ( + -0.2mm). Window profile with hollow section with multi chamber, frame (60mm x 58mm), sash (60mm x 78mm). T profile (One vertical length in between two shutters) (60mm x 74mm). Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling ol holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket 1.2 + -0.2mm thick galvanized steel Frame (28mm x 21.5mm), sash (31mm x 27mm), T profile (27mm x 17mm) to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners. Hardware: [casement door handle made of zinc alloyed (white powder coated). Corner striker. Secondary Strikers. Cylinder. Door transmission gear made of mild steel with multi point locking system with strikes. 3D Hinges of zinc alloyed (white powder coated) [and 5mm thick glazing with selected quality glass complete all as specified and as directed. |
| 108 | M&L for powder coated aluminium frame for doors, windows, ventilators (minimum thickness of powder coating 50 micron) with one or more rebates including joining cleat for fixing etc. complete all as specified and directed. |
| 109 | M&L for powder coated aluminium door shutters (thickness or powder coating shall not be less than 50 microns of approved colour) aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, lock with 2 keys, anodized aluminium snap beading screws etc. complete all as specified and as directed. |
| 110 | S&F in repair Aluminium (die cast) body Door closer hydraulically regulated, designation No. 2, universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 kg complete all as specified and as directed. |
| 111 | S&F 5 mm thick sheet glass, ordinary quality and fixing with rubber beading area n exc. 0.5 square metre in each pane etc complete all as specified and as directed. |
| 112 | S&F 5 mm thick sheet glass, ordinary quality and glazing with rubber beading area exc. 0.5 square metre in each pane etc complete all as specified and as directed. |
| 113 | S&F 12 mm thick Pre-laminated particle board, interior grade, pre-laminated both sides decorative with plain white coloured lamination fixed to aluminium shutter complete all as specified and as directed. |
| 114 | S&F in repair fancy type curtain rod 20 mm dia mild steel, chromium plated with fixing brackets, including side brackets, complete all as specified. |
| 115 | Taking down aluminium shutters and dismantling stiles and rails including glass panes/particle board carefully, re-fabricating and re-fixing in frame position using all old material including neoprene replacement of required packing, cleats, screws complete all as specified and as directed |
| 116 | S&F 18 mm thick WPC board both side decorative fixed with screws, solvent cement/ adhesive/bolts to make kitchen cabinet sides top and bottom and shelves inside the cabinets etc. complete as per specifications and as directed. |
| 117 | S&F 18 mm thick Rajshri WPC board of Single Side Prelam/ Rigidlam color fixed with screws, solvent cement/ adhesive to make kitchen cabinet sides top and bottom and shelves inside the cabinets complete as per specifications and as directed by Engineer-in-Charge. (Density- 575 to 600 Kg/CBM) |
| 118 | S&F 12 mm thick Rajshri WPC board of plain white(Matt finish) colour fixed with screws, solvent cement/ adhesive to make wall mount kitchen cabinet back and pull out drawer sides complete as per specifications and as directed by Engineer-in-Charge- ( Density- 575 to 625 KG/CBM) |
| 119 | S&F in 100 mm size aluminium anodised Hasp and staple, safety type, with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and as directed. |
| 120 | S&F auto closing hinges 35 mm of 0 crank( KH-001)OR 8 crank (KH-002) openable at 110 degree for kitchen cabinet shutters complete all as specified and as directed. |
| 121 | Demolition of cement Concrete in ground floors and pavings not exc 15 cm thickness (below or above ground level) complete all as specified and as directed. |
| 122 | M&L for 50mm thick cement concrete 1:3:6, type C1 (using 20 mm graded stone aggregate) as in plinth protection, finishing cement concrete surface even and fair without using extra cement complete all as specified and as directed. Please Enable Macros to View BoQ information |
| 123 | M&L for 50mm thick cement concrete 1:3:6, type C1 (using 20 mm graded stone aggregate) as in plinth protection, finishing cement concrete surface even and fair without using extra cement complete all as specified and as directed. Please Enable Macros to View BoQ information |
