Tender For Construction Of Combined Building Of Gos Mess For Eastern Frontier And Shq (Lko) At Darogakhera, Eastern Frontier, Itbp, Lucknow, Darogakheda Lucknow-Uttarakhand

TDR : 55954526

Tender Notice
BOQ

18 Days Left

Darogakheda Lucknow , Uttarakhand

Tender Brief : Tender For Construction Of Combined Building Of Gos Mess For Eastern Frontier And Shq (Lko) At Darogakhera, Eastern Frontier, Itbp, Lucknow

Document Fees
Refer document

EMD
₹ 2345639.0 /-

Tender Value
₹ 13.45 Crore /-

Submission Date
04-07-2026

Competition Type
Indian

Bidding Type
Tender

Need a Business Loan? Apply Now !


1	Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and for all lift, as directed by Engineer-incharge. All kinds of soil
2	Excavating trenches by mechanical / manual means of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, for all depth, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : All kinds of soil Pipes, cables etc. exceeding 80 mm dia. But not exceeding 300 mm dia
3	Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.
4	Carriage of Earth by mechanical transport including loading, unloading and Stacking including royalty & carriage up to 5 KM complete.
5	Supplying and filling in plinth with sand under floors including, watering, ramming consolidating and dressing complete.
6	Surface dressing of the ground including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift upto1.5 m. All kinds of soil.
7	Supplying chemical emulsion in sealed containers including delivery as specified . chlorpyriphos/ Lindane emulsifiable concentrate of 20%
8	Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) : Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor : With Chlorpyriphos/Lindane E.C. 20% with 1% concentration.
9	Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources)
10	Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)
11	Centering and shuttering including strutting, propping etc. and removal of form work for : Foundations, footings, bases for columns
12	Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20mm nominal size derived from natural sources).
13	Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer's specification.
14	Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with apiece of cloth lightly soaked in kerosene oil.
15	Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.
16	Centering and shuttering including strutting, propping etc. and removal of form for :Foundations, footings, bases of columns, etc. for mass concrete
17	Centering and shuttering including strutting, propping etc. and removal of form for: Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.
18	Centering and shuttering including strutting, propping etc. and removal of form for : Suspended floors, roofs, landings, balconies and access platform.
19	Centering and shuttering including strutting, propping etc. and removal of form for : Shelves (Cast in situ)
20	Centering and shuttering including strutting, propping etc. and removal of form for: Lintels, beams, plinth beams, girders, bressumers and cantilevers
21	Centering and shuttering including strutting, propping etc. and removal of form for: Columns, Pillars, Piers, Abutments, Posts and Struts.
22	Centering and shuttering including strutting, propping etc. and removal of form for: Stairs, (excluding landings) except spiral-staircases.
23	Centering and shuttering including strutting, propping etc. and removal of form for: Small lintels not exceeding 1.5m clear span, moulding as in cornices, window sills, string courses, bands, copings, bed plates, anchor blocks and the like.
24	Centering and shuttering including strutting, propping etc. and removal of form for: Edges of slabs and breaks in floors and walls Under 20 cm wide
25	Centering and shuttering including strutting, propping etc. and removal of form for: Weather shade, Chajjas, corbels etc., including edges.
26	Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc., including cost of de-shuttering and decentering at all levels, over a height of 3.5 m, for every additional height of 1 metre or part thereof (Plan area to be measured). Suspended floors, roofs, landing, beams and balconies (Plan area to be measured)
27	Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.
28	Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.
29	Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. Concrete of M30 grade with minimum cement content of 350 kg /cum
30	Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.All works above plinth level upto floor V level . Concrete of M30 grade with minimum cement content of 350 kg /cum
31	Add for using extra cement in the items of design mix over and above the specified cement content therein.
32	Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:Cement mortar 1:4 (1 cement : 4 coarse sand)
33	Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1:6 (1 cement : 6 coarse sand)
34	Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.Cement mortar 1:4 (1 cement :4 coarse sand)
35	Extra for providing and placing in position 2 Nos. 6mm dia. M.S. bars at every third course of half brick masonry (with F.P.S. bricks).
36	Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite stone slab colour black, Cherry/Ruby red Area of slab upto 0.50 sqm
37	Area of slab over 0.50 sqm
38	Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite work
39	Extra for providing opening of required size & shape for wash basins/ kitchen sink in kitchen platform, vanity counters and similar location in marble/Granite/Stone work including necessary holes for pillar taps etc. including rubbing and polishing of cut edge etc. complete.
40	Providing wood work in frames of false ceiling, partitions etc. sawn and fixed in position with necessary stainless steel screws etc. Sal wood
41	9.20 Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 9.20.1 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws sqm
42	Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured).
43	Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to openings /wooden frames with rawl plugs screws etc.
44	Providing and fixing curtain rods of 1.25 mm thick chromium plated brass plate, with two chromium plated brass brackets fixed with C.P. brass screws and wooden plugs, etc., wherever necessary complete : 20 mm dia
45	Providing and fixing special quality bright finished brass cupboard or ward robe locks with four levers of approved quality including necessary screws etc. complete. 50 mm.
46	Providing and fixing 50 mm bright finished brass cup board or wardrobe knob of approved quality with necessary screws.
47	Providing and fixing magnetic catcher of approved quality in cupboard / ward robe shutters, including fixing with necessary screws etc. complete.Double strip (horizontal type).
48	Providing and fixing stainless steel fancy handle of approved make fixed with SS screws etc. complete as per direction of Engineer-in-charge.200 mm
49	Providing and fixing stainless steel soft closing heavy type telescopic drawer channels of approved make 500 mm long with screws etc. complete as per direction of Engineer- in-charge.
50	Providing and fixing factory made P.V.C. door frame of size 50x47 mm with a wall thickness of 5 mm, made out of extruded 5mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturer’s specification and direction of Engineer-in-Charge.
51	Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm thick heat moulded PVC ‘C’ channel of size 30mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7 mm (5 mm+2 mm) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the ‘C’ Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge, manufacturer’s specification & drawing. 30 mm thick plain PVC door shutters.
52	Providing and fixing cup board shutters 25 mm thick, with Pre-laminated flat pressed three layer particle board or graded wood particle board IS: 12823 marked, exterior grade (Grade l Type ll), having one side decorative lamination and other side balancing lamination, including IInd class teak wood lipping of 25 mm wide x12 mm thick with necessary screws and bright finished stainless steel piano hinges, complete as per direction of the Engineer-in-Charge
53	Providing and fixing bright finished brass 100 mm mortice latch with one dead bolt and a pair of lever handles of approved quality with necessary screws etc. complete.
54	Providing and fixing aluminium sliding door bolts, ISI marked anodised anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 250x16 mm
55	Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete : 300x10 mm
56	Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete : 200x10 mm
57	Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete : 150x10 mm
58	Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete : 100x10 mm
59	Providing and fixing aluminium pull bolt lock, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws bolts, nut and washers etc. complete.
60	Providing and fixing 50 cm long aluminium kicking plate of size 100x3.15 mm, anodised (anodic coating not less than grade AC 10 as per IS :1868) transparent or dyed to required colour or shade, with necessary screws etc. complete.
61	Providing and fixing aluminium handles of approved make anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessry screws etc. complete. 125 mm
62	Providing and fixing aluminium handles of approved make anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessry screws etc. complete. 100 mm
63	Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with necessary screws etc. complete. Single rubber stopper
64	Providing and fixing bright finished 100 mm mortice lock with 6 levers without pair of handles of approved quality for aluminium door, with necessary screws etc complete as per direction of Engineerin-charge.
65	Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.
66	Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt / suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. 1.0 mm thick
67	Providing and fixing fly proof stainless steel grade 304 wire gauge, to windows, Doors and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia. 0.50 mm all complete. With aluminium Snap beading.
68	Providing and fixing factory made uPVC glazed/wire mesh windows/doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and Inline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod pf approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge. Wire mesh / Glazing of plain/ toughened/ laminated/ double glass unit with / without high performance coatings as per design requirements and conforming to IS: 3548 & IS:16231 shall be paid separately. Note:- Structural design proof checked from a Government Engineering Institute, to be provided by the manufacturer for: (i) Sites with basic wind speed > 45 m/sec as per IS 875 - Part 3 (ii) Sites with structure height more than 20m for all wind speeds. Casement Window with Double Rebate Frame with two Side Hung Glazed Panel and two Side Hung wire mesh Panel and Fixed Mullion with S.S. 304 friction hinges as per size and weight of sash, multi-point locking system, zinc alloy (zamak) powder coated handles on both glazed and fly screen panel.Using R3 series with frame (110mm & above ) x (45mm & above) & glazed sash (55mm & above) x (65mm & above) & fly screen sash (30mm & above) x (55mm & above) & mullion (55mm & above) x (65mm & above) & metal grill (if required to be paid separately). (Height upto 1.8 meter) Fixed window / ventilator with mullion / transom.
69	Using R1 series with frame (33mm & above ) x (35mm & above) & mullion (33mm & above) x (50mm & above). (Height upto 0.90 meter)
70	Ventilator Casement window single panel with or without fixed panel with S S. 304 friction hinges as per size and weight of sash, single point locking zinc alloy (zamak) powder coated handles. Using R1 series with frame (33mm & above ) x (35mm & above) & sash /mullion (33mm & above) x (50 mm & above). (Height upto 0.90 meter).
71	Casement Door with Double Rebate Frame with one Side Hung Glazed Panel and one Side Hung wire mesh Panel with zinc alloy (zamak) 3D hinges, multi- point locking system with cylinder, zinc alloy (zamak) powder coated handles on both sides of glazed panel and zinc alloy (Zamak) powder coated handle along with multi-point locking system on one side of fly screen panel.Using R3 series with frame (110mm & above) x (45mm & above) & glazed sash (55mm & above) x (85mm & above) & fly screen sash (55mm & above) x (65mm & above). (Height upto 2.5 meter).
72	Providing and fixing casement handle made of zinc alloyed (white powder coated) for uPVC casement window with necessary screws etc. complete.
73	Providing and fixing, in position concealed G.l. section for wall paneling using Panel of required thickness fixed on the 'W profile (0.55 mm thick) having a knurled web of 51.55 and two flanges of 26mm each with lips of 10.55mm placed @610mm c/c mm with thickness of 0.55 mm and web in perimeter channel having one flange of 20mm and another flange of 30mm with thickness of 0.55 mm and web of length 27 mm. Perimeter channel is fixed on the floor and the ceiling with the nylon sleeves @610 mm C/C with fully threaded self-tapping dry wall screws. Panel is fixed to the W profile with 25 mm countersunk ribbed head screws @ 200 mm C/C., all complete as per the drawing & directions of engineer-in-charge, the joints of the boards are finished with specially formulated jointing compound and 48mm wide jointing tape to provide seamless finish. 10mm thick PVC Panel
74	Providing and fixing 18mm thick both sides Pre-laminated cement bonded wood particle board: 15786:2008 of approved brand and shade with suitable full threaded steel screwsetc. in partitions, boxes, shelves, racks and cupboard, kitchen cabinet under kitchen counter. all complete as per direction of Engineer-in-charge (Note: Fittings to be paid separately). 18 mm thick
75	Providing and fixing 6 mm thick both sides Pre-laminated cement bonded wood particle board as per IS : 15786:2008 of approved brand and shade with suitable full threaded steel screws etc. on the backing of racks, drawer, cupboard, kitchen cabinet under kitchen counter etc. all complete as per direction of Engineer-in-charge.
76	Providing and fixing stainless steel soft closing spring hinges at 0 degree hinges (hydraulic type) of approved make/brand to cupboard shutters with full threaded steel screws including making necessary recess in board and finished etc. complete as per direction of Engineer-in-charge
77	Providing and fixing stainless steel soft closing heavy type telescopic drawer channels of approved make 500 mm long with screws etc. complete as per direction of Engineer- in-charge.
78	Providing and fixing ready made 304 grade stainless steel Modular kitchen basket and accessories such as right angle basket (Plain Cup & Saucer, plant, Partition, Bottle rack, Thali, Cutlery) kitchen utensil basket, Dinner set basket, kitchen grain basket, Multipurpose basket as per site requirement including finishing (wherever required) and fittings. The same shall be fixed with necessary stainless steel nuts & bolts, Stainless Steel screws & telescopic channel etc. as per direction of Engineer-in charge. (For payment purpose only weight of Stainless steel basket shall be considered excluding weight of all fixing accessories such as nuts, bolts, fasteners telescopic basket channels etc. Payment of providing and fixing telescopic channel shall be paid separately)
79	Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : Powder coated aluminium (minimum thickness of powder coating 50 micron) kg 530.90
80	Providing and fixing 2 mm thick 16 to 19 mm wide PVC edge binding tape of approved quality for cupboard/wardrobe shutters including necessary synthetic resin hot pressed to edges on binding machine etc. complete as per direction of Engineer- in-charge
81	Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer. Using M.S. angels 40x40x6 mm for diagonal braces
82	Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge: Profile B Fixing with adjustable lugs with split end tail to each jamb
83	Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.
84	Steel work welded in built up sections/ framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required In stringers, treads, landings etc. of stair cases including use of chequered plate wherever required, all complete.
85	In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.
86	Providing and fixing carbon steel galvanised ( minimum coating 5 micron) dash fastener of 10 mm dia double threaded 6.8 grade (yield strength 480 N/mm2), counter sunk head, comprising of 10 m dia polyamide PA 6 grade sleeve, including drilling of hole in frame , concrete/ masonry, etc. as per direction of Engineer-in-charge. 10 x 60 mm
87	Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).
88	Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate
89	Extra for pre finished nosing to treads of steps of marble / granite stone.
90	Extra for marble / granite stone flooring in treads of steps and risers using single length up to 2.00 metre.
91	Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement: 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.
92	Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed vitrified floor tiles polished finish of Size of Tile 800 x 800 mm
93	Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed vitrified floor tiles polished finish of.Size of Tile 1200 x 1200 mm
94	Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed vitrified floor tiles polished finish ofGlazed Vitrified tiles Matt/Antiskid finish of size Size of Tile 600 x 600 mm
95	Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab colour of Black, Cherry/Ruby Red or equivalent
96	Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : In 75x75 mm deep chase
97	Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.
98	Providing and fixing false ceiling at all heights including providing and f ixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and f inishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer’s specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum moisture resistant board
99	Providing 10 mm thick plaster of Paris (gypsum anhydrous) ceiling up to a height of 5 m above floor level, over first class kail wood strips 25x6 mm with 10 mm gap in between and reinforced with rabbit wire mesh fixed to wooden frame (frame work to be paid separately): Flat surfaces
100	Providing 10 mm thick plaster of Paris (gypsum anhydrous) ceiling up to a height of 5 m above floor level, over first class kail wood strips 25x6 mm with 10 mm gap in between and reinforced with rabbit wire mesh fixed to wooden frame (frame work to be paid separately): Curved surfaces
101	Extra for sunk or raised mouldings in the plaster of Paris (Gypsum anhydrous) ceiling.
102	Providing and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI (solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, including rubbing and polishing of the surface upto 3 cuts complete, including providing skirting upto 150 mm height along the parapet walls in the same manner.
103	12 mm cement plaster of mix : 1:6 (1 cement: 6 coarse sand)
104	15 mm cement plaster on rough side of single or half brick wall of mix :1:6 (1 cement: 6 coarse sand)
105	20 mm cement plaster of mix : 1:4 (1 cement: 4 coarse sand)
106	6 mm cement plaster of mix : 1:3 (1 cement: 3 fine sand)
107	Extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers.
108	Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof. 10 to 13m
109	Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof. 13 to 16m
110	Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.
111	Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : Water thinnable cement primer.
112	Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade : Two or more coats on new work
113	Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm
114	Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work
115	Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections.
116	Providing and fixing wpc/fluted wall panelling , with screw fitting wherever required :- 10 mm thick heavy panel
117	Providing and fixing Wallpapers , vinyl (PVC-coated paper or fabric-backed).Vinyl/Laminated: multiple layers weights 330–400 GSM heavy-dutyTextured Embossed,self-adhesive Removable, Waterproof, Heat resistant, Oil-resistant, Re-positionable and Eco-friendly.
118	Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete
119	Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earth with lead upto 50 metres.
120	Extra for compaction of earth work in embankment under optimum moisture conditions to give at least 95% of the maximum dry density (proctor density).
121	Providing and laying design mix cement concrete of M-30 grade, in roads/taxi tracks/ runways, using cement content as per design mix, using coarse sand and graded stone aggregate of 40 mm nominal size in appropriate proportions as per approved & specified design criteria, providing dowel bars with sleeve/ tie bars wherever required, laying at site, spreading and compacting mechanically by using needle and surface vibrators, levelling to required slope/ camber, finishing with required texture, including steel form work with sturdy M.S. channel sections, curing, making provision for contraction/ expansion, construction & longitudinal joints ( 10 mm wide x50 mm deep) by groove cutting machine, providing and filling joints with approved joint filler and sealants, complete all as per direction of Engineerin- charge (Item of joint fillers, sealants, dowel bars with sleeve/ tie bars to be paid separately). Note:-Cement content considered in M-30 is @ 340 kg/cum. Excess/ less cement used as per design mix is payable/ recoverable separately. Cement concrete manufactured in automatic batching plant (RMC plant) i/c transportation to site in transit mixer
122	Extra for providing and mixing hardening compound of approved quality as per manufacturer’s specification in cement concrete.
123	Providing and fixing in position pre-moulded joint filler in expansion joints.
124	Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge. With material conforming to Grade-I (size range 75 mm to 0.075 mm) having CBR Value-30
125	Construction of dry lean cement concrete sub base over a prepared sub-grade with coarse and fine aggregate conforming to IS:383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per specifications, cement content not to be less than 150 Kg/cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant, transported to site, for all leads & lifts, laid with a mechanical paver, compacting with 8-10 tonne vibratory roller, finishing and curing etc. complete as per direction of Engineer-in-charge.
126	Providing and laying factory made coloured chamfered edge Cement Concrete paver blocks of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of fine sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with jamuna sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand in footpath, parks, lawns, drive ways or light traffic parking etc. complete as per manufacturer’s specifications & direction of Engineerin-Charge. 60mm thick C.C. paver block of M-35 grade with approved colour, design & pattern.
127	Providing and laying at or near ground level factory made kerb stone of M- 25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).
128	Providing and laying 100 micron thick Pvc Sheet (Overlaps at joints of PVC Sheet should be 100mm wide and pasted to each other with suitable adhesive over WMM road surface as per the direction of Engineer-in-Charge.
129	Supplying and stacking at site dump manure from approved source, including carriage upto 5 km complete (manure measured in stacks will be reduced by 8% for payment) : Screened through sieve of I.S. designation 16 mm
130	Fine dressing of the ground.
131	Spreading of sludge, dump manure and/or good earth in required thickness as per direction of officer-in-charge (cost of sludge, dump manure and/ or good earth to be paid separately).
132	Mixing earth and sludge or manure in the required proportion specified or directed by the Officer-in-charge
133	Grassing with selection No. 1 grass including watering and maintenance of the lawn for 60 days or more till the grass forms a thick lawn, free from weeds and fit for mowing including supplying good earth, if needed (the grass and earth shall be paid for separately). With grass Turf
134	Preparation of beds for hedging and shrubbery by excavating 60 cm deep and trenching the excavated base to a further depth of 30 cm, refilling the excavated earth after breaking clods and mixing with sludge or manure in the ratio of 8:1 (8 parts of stacked volume of earth after reduction by 20% : one part of stacked volume of sludge or manure after reduction by 8%), flooding with water, filling with earth if necessary, watering and finally fine dressing, leveling etc. including stacking and disposal of materials declared unserviceable and surplus earth by spreading and leveling as directed, within a lead of 50 m, lift up to 1.5 m complete (cost of sludge, manure or extra earth to be paid for separately)
135	Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately) : Holes 60 cm dia, and 60 cm deep
136	Providing and laying Neelgiri/Mexican grass turf with earth 50mm to 60mm thickness of existing ground prepared with proper level and ramming with tools wooden (Dhurmos) and than rolling the surface with light roller make the surface smoothen and light waterning with sprinkler and maintenance for 30 days or more till the grass establish properly, as per direction of officer-in-charge.
137	Anti termite treatment of lawn area through premise 30.50% I P. one liter premise diluted in 499 liters water and applying solution @ 1.00 litre solution per sqm lawn or bed area.(two application) i/c cost of chemical)and as per direction of officer-in-charge.and as per direction of officer-in-charge.
138	Providing and Displaying Bougainvillea named variety, Sobhra, Thima, Marry palmar, Cherry Blossom etc. well developed with fresh & healthy bushy plant in full bloom 75 to 90 cm ht. in 40 cm Cement Pot as per direction of the officer-in-charge.
139	Supply and stacking of Bauhinia blakeana (Kachnar) plant of height 120- 150 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.
140	Supply and stacking of plant Hibiscus rosasinensis of height 45-60 cm. with 3-4 branches in earthen pots of size 20 cm as per direction of the officer-in-charge.
141	Preparation of mounds of various size and shape by available excavated / supplied earth in layers not exceeding 20 cm in depth, breaking clods, watering of each layer, dressing etc., lead upto 50 meter and lift upto 1.5 m complete as per direction of Officer-in-charge.
142	Providing Circular Cement Concrete pots of specified size, cast with cement concrete of nominal mix 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 6 mm nominal size), reinforced with 7 Nos (3 nos horizontal & 4 nos vertical “ U “ shape) M.S. wires of 3.5 mm dia as per design, including required form work, finishing with cement punning on exposed surface, curing for specified period and stacking in required rows & height, all complete as per direction of Officer-in-charge. 2.29.1 Top inside dia 35 cm, outer bottom dia 25 cm, total height 35 cm with wall thickness of 25.4 mm
143	Providing and stacking of Bignonia venusta (Golden shower) of height 30 cm to 45 cm. in 20 cm size of Earthen pot / Plastic pot as per direction of the officer-in-charge.
144	Providing and stacking of Jasmine humile (Yellow) of height 30 cm to 45 cm. in 20 cm size of Earthen pot / Plastic pot as per direction of the officer-in-charge.
145	Supply and stacking of plant Tabernaemontana coronaria (Chandni single) of height 90-105 cm,bushy in big size HDPE bag as per direction of the officer-in-charge.
146	Supply and stacking of plant Tecoma gaudichaudi of height 90-105 cm.,bushy in big size HDPE bag as per direction of the officer-in-charge.
147	Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineerin-charge. Pre-laminated particle board with decorative lamination on both sides
148	Providing and fixing glazing in UPVC/ aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm)
149	Providing and fixing glazing in UPVC/ aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 8 mm thickness (weight not less than 20 kg/sqm)
150	Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg., for doors, including cost of cutting floors ,embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge With stainless steel cover plate minimum 1.25 mm thickness.
151	Filling the gap in between aluminium frame and adjacent RCC/Brickwork/ Stone Work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge. Upto 5mm depth and 5mm width
152	Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately).
153	Providing and fixing Pull Handle back to Back (Article code: 903.05.700) Hafele/Dorma/Godrej & Boyce or eq. makes of Fixing 25mm dia x300mm c/c, SS Matt with necessary screws etc. complete as per direction of Engineer-in-Charge.
154	Providing and fixing Corner Patch Lock With Cylinder (Article code: 981.50.030) Hafele/Dorma/Godrej or eq. makes, SS Matt with necessary screws etc. complete as per direction of Engineer-in-Charge.
155	Providing and fixing of 12 mm Aluminium Composite Panel laser cut jali with design as per drawing to be fixed over the frame work of 48mm GI Stud/ 50mm M.S Section. The framework to be supported on the wall at a distance of 1800 mm centre to centre of size as reqd long 35x35x3mm angle cleats of required length and MS anchor fasteners of size 65mm x10mm dia. The cleats to be given two or more coats of red oxide primer. The entire work to be executed as per the drawings / instructions of the Engineer-in-charge. The rate includes for all Geometry of wall, openings etc. and for complete item including all the required approved material, labour and fixing as per drawings enclosed. The work shall be executed as per specification , & instructions of engineer in charge.
156	Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of : (i) Ist course of applying cement slurry @ 4.4 Kg/Sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface. (ii) IInd course of 20mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface. (iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 Kg. per Sqm of area. (iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 Kg/Sqm.)
157	Supplying and Stacking Filling sunken floor with over burnt jhama brick aggregate 120mm to 40mm including compacting of materials complete as specified and directed for all levels.
158	Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge. (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. (e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. All above operations to be done in order and as directed and specified by the Engineer-in-Charge : With average thickness of 120 mm and minimum thickness at khurra as 65 mm.
159	Providing and fixing floor mounted, white vitreous china single piece, double traps syphonic water closet of approved brand/make, shape, size and pattern including integrated white vitreous china cistern of capacity 10 litre with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect model Cera- CHANEL or equivalent as per directions of Engineer-in-Charge.
160	Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid
161	Providing and fixing Under Counter Wash Basinwash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 580x430 mm make-Hindware Garnet or eqivalent
162	Supplying, fitting and fixing 15 mm Chrome Plated (C.P.) basin mixer complete as directed.
163	Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :Kitchen sink without drain board 610x510 mm bowl depth 200 mm
164	Supply, Receiving, Storing & Fixing of CP brass wall mounted sink mixer with C.P. wall flange, swinging spout complete as required with flow rate of 6.0 LPM complying to Green Building requirements.
165	Providing,fixing,testing and commissioning Hand Shower (Health Faucet) with 8mm Dia,1 Metre Long Flexible Tube & Wall Hook of approved make and manufacture complete as per direction of Engineer in Charge.
166	Providing and fixing CP Brass 32mm size bottle trap of approved quality & make and as per the direction of engineer in charge.
167	Providing and fixing toilet paper holder C.P. brass
168	Supply, Receiving, Storing & Fixing of C.P. brass twin coat hook with PVC rawl plug & C.P. brass screw complete as required. Make :
169	Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931. 15mm nominal bore
170	Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour. 15 mm nominal bore with 45 cm length
171	Providing and fixing of C. P. brass towel rail 600 x 20 mm size complete with C.P. brass brackets.
172	Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge.
173	Providing and fixing 75 mm high, 50 mm deep and 18 mm thick stone slab table rubbed, edges rounded and polished, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth. Granite Stone of approved shade
174	Supply and fixing of water cooler with RO fully stainless steel of 60 litres cooling capacity and 120 litres storage capacity to be operated on single phase supply with ISI mark. Each Cooler shall be provide with 4 Nos pessmatic tap for Drinking purpose.
175	Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.
176	Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : Rectangular shape 1500x450 mm
177	Providing and fixing 600x120x5 mm glass shelf with edges round off,supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc.,complete.
178	Providing and fixing SS robe hook inspired by bold geometry of the Rubik's cube with necessary screws and making walls good. Suitable for hanging of cloths upto 5 Kg, minimum two hooks on cube.
179	Providing and fixing SS towel ring with necessary screws and making wall good. The ring should be wall mounted and suitable for hanging of towel/ cloths upto 5 Kg.
180	Providing and fixing SS liquid soap container (froasted glass container) and with necessary screws and making wall good. The item should be wall mounted and suitable 250 ML soap.
181	Providing and fixing Towel rack with necessary screws and making wall good. The item should be wall mounted with a conceled screws and suitable for hanging towel/ clothes upto 5 Kg, Minimum 3 Top bars and 1 bottom bar.
182	Providing and fixing Shower panel suitable for hot and cold water flow in foaming form. The item should be wall mounted with a conceled screws. Minimum 1 overhead shower fixed for telephonic type, with water pressure adjustable system.Size 1400 x 200 mm Focussed Body Jets with Three Functions: Rain, Body Jets make CERA Rivere or equivalent as per approval of Engineer in-charge.
183	Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Flexible pipe. 40 mm dia
184	Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet arm. 150 mm diameter
185	Providing and Fixing, testing and commissioning of CP Brass Telephone wall mixer with provision of overhead shower with 115mm long bend pipes on upper size with connecting legs , divertor and wall flanges with all accessories as required and making good the walls wherever required.
186	Providing and fixing CP brass soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.
187	Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore
188	Supplying, Installation, Testing and Commissioning of vertical / horizontal storage type hot water heater fixed to wall with anchor bolts & nuts all complete work, (for Kitchen, Pantry & Toilets)20 Liter capacity.
189	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall 20 mm dia nominal bore
190	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall 25 mm dia nominal bore
191	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall 32 mm dia nominal bore
192	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall 40 mm dia nominal bore
193	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall 50 mm dia nominal bore
194	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall 65 mm dia nominal bore (Sch. 40)
195	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 15 mm nominal dia Pipes
196	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 20 mm nominal dia Pipes
197	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 25 mm nominal dia Pipes
198	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 32 mm nominal dia Pipes
199	Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 20mm nominal bore
200	Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 25mm nominal bore
201	Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 32mm nominal bore
202	Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 40mm nominal bore
203	Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 50mm nominal bore
204	Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 65mm nominal bore
205	Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. 32 mm dia nominal bore
206	Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. 40 mm dia nominal bore
207	Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.
208	Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S.(non modular) bricks of class designation 7.5
209	Providing and fixing motorized valve with sensor of approved quality, to complete the work. 32 mm dia
210	Providing and fixing motorized valve with sensor of approved quality, to complete the work. 40 mm dia
211	Supply, Installation, Testing and Commissioning of mineral filled 3 layered (PP/PP mineral filled/PP) Polypropylene low noise pipes and fittings of min. density 1.9 gm/cm3, pipes of 40 mm – 200 mm including all fittings & accessories such as coupler, elbow, tee, Y, reducer, access door, end cap, cowls, etc. for soil, waste and vent purpose in floors, ceiling suspended, or on walls, with leak proof joints etc. Joining pipes & fittings with rubber sealing rings as per approved. 110 mm (For Single & public toilets Soil & Waste Pipe).
212	Supply, Installation, Testing and Commissioning of mineral filled 3 layered (PP/PP mineral filled/PP) Polypropylene low noise pipes and fittings of min. density 1.9 gm/cm3, pipes of 40 mm – 200 mm including all fittings & accessories such as coupler, elbow, tee, Y, reducer, access door, end cap, cowls, etc. for soil, waste and vent purpose in floors, ceiling suspended, or on walls, with leak proof joints etc. Joining pipes & fittings with rubber sealing rings as per approved. 75 mm (For Vent Pipe).
213	Supply, Installation, Testing and Commissioning of mineral filled 3 layered (PP/PP mineral filled/PP) Polypropylene low noise pipes and fittings of min. density 1.9 gm/cm3, pipes of 40 mm – 200 mm including all fittings & accessories such as coupler, elbow, tee, Y, reducer, access door, end cap, cowls, etc. for soil, waste and vent purpose in floors, ceiling suspended, or on walls, with leak proof joints etc. Joining pipes & fittings with rubber sealing rings as per approved. 40 mm dia (For Urinal Soil Pipe).
214	Supply, Installation, Testing and Commissioning of mineral filled 3 layered (PP/PP mineral filled/PP) Polypropylene low noise pipes and fittings of min. density 1.9 gm/cm3, pipes of 40 mm – 200 mm including all fittings & accessories such as coupler, elbow, tee, Y, reducer, access door, end cap, cowls, etc. for soil, waste and vent purpose in floors, ceiling suspended, or on walls, with leak proof joints etc. Joining pipes & fittings with rubber sealing rings as per approved. 50 mm dia (For FD to FT Waste Pipe).
215	Supplying, Installation, Testing and Commissioning of (PP/PP mineral), P or S trap of self cleansing design with / without vent. arm Setting in cement concrete 1:2:4 mix complete including cost of cutting & making good the Wall / Floors wherever required. 110 x110 mm outlet
216	Providing and fixing (PP/PP mineral) floor drain 110X75 size inlet and outlet including cutting and making good the walls and floors wherever required complete in all respects.
217	Providing & fixing (PP/PP mineral) clean out plug with uPVC socket fixed to uPVC pipe joints as required complete in all. 100 mm dia Pipe
218	Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including cost of cutting holes and making good the walls etc. : For 100 mm dia pipe
219	Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including cost of cutting holes and making good the walls etc. : For 75 mm dia pipe
220	Providing and fixing chrome plated grating with ring and two S.S screws of approved design with grating screwed down to the ring with s/s screws and embedding and setting ring into the floor with cement mortar.
221	Providing and fixing uPVC cowel of approved quality 110 mm
222	Providing and fixing uPVC cowel of approved quality 75 mm
223	Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.450 X 450mm -
224	Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams.
225	Supplying, Installation, Testing and Commissioning of uPVC pipes conforming to IS 4985 class III (6 kg/cm2) for rain water pipes including all fittings rubber ring type (plain or with access door) e.g. bends, junctions, cowls, offsets, access pieces, jointing with rubber ring joints with lubricant etc. fixed with clamps to walls with cement concrete 1:2:4 blocks complete in all respects. (For rain water Pipe). 75 mm diameter
226	Supplying, Installation, Testing and Commissioning of uPVC pipes conforming to IS 4985 class III (6 kg/cm2) for rain water pipes including all fittings rubber ring type (plain or with access door) e.g. bends, junctions, cowls, offsets, access pieces, jointing with rubber ring joints with lubricant etc. fixed with clamps to walls with cement concrete 1:2:4 blocks complete in all respects. (For rain water Pipe). 110 mm diameter (with all fittings)
227	Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : All kinds of soil Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia
228	Supplying and laying of following size HDPE DWC pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 16098, Part II complete with fitting and cutting,jointing etc.direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required. 150 mm dia. Pipe
229	Supplying and laying of following size HDPE DWC pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 16098, Part II complete with fitting and cutting,jointing etc.direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required. 200 mm dia. pipe
230	Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round DWC pipes including bed concrete as per standard design : 150 mm dia. DWC & RCC Pipe
231	Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round DWC pipes including bed concrete as per standard design : 200 mm dia. DWC & RCC Pipe
232	Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round DWC pipes including bed concrete as per standard design : 250 mm dia. DWC & RCC Pipe
233	Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design : 150 x 100mm size P-type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
234	Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 150 mm dia. R.C.C. pipe
235	Providing and laying non-pressure NP2 class (light duty) R.C.C.with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 250 mm dia. R.C.C. pipe
236	Constructing brick masonry manhole in cement mortar 1:4 ( 1cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominalsize), inside plastering 12 mm thick with cement mortar 1:3 (1 cement: 3 coarse sand) finished with floating coat of neat cement andmaking channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : 19.7.1.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
237	Constructing brick masonry manhole in cement mortar 1:4 ( 1cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominalsize), inside plastering 12 mm thick with cement mortar 1:3 (1 cement: 3 coarse sand) finished with floating coat of neat cement andmaking channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (medium duty) 500 mm internal diameter, total weight of cover and frame to be not less than 116 kg (weight of cover 58 kg and weight of frame 58 kg) : 19.7.2.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
238	Extra for depth for manholes :Size 90x80 cm, With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
239	Extra for depth for manholes Size 120x90 cm With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
240	Constructing brick masonry road gully chamber 50x45x60cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450mm precast RCC horizontal grating with frame complete as per standard design. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
241	Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910 on 12mm dia steel bar conforming to IS : 1786 having minimum cross section as 23 mmx25mm and over all minimum length 263 mm and width as 165mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture's permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design.
242	Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement and making necessary channels for the drain etc. complete : For pipes 250 to 300 mm diameter
243	(a) Supplying, installation, testing and commissioning of electric driven terrace pump conforming to IS 12469: 2019 suitable for automatic operation and consisting of following, complete in all respects, as required: (Terrace Pump) (b) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal as required. (c)Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure, horiziontal foot mounted type with Class 'F' insulation, conforming to IS-12615: 2018. (d) M.S.fabricated common base plate, coupling, coupling guard, foundation bolts etc.as required. (e) Suitable cement concrete foundation duly plastered and with anti vibration pads. 450 lpm at 35 m Head
244	Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 4 x 25 sqmm ( 28 mm )
245	Supplying & laying one number XLPE insulated PVC sheathed Aluminium Conductor armoured UG cable of 1.1 KV grade Conforming to IS 7098/1988 with upto date ammendment of following size in the existing RCC/HUME/ METAL /GI /CI /Stoneware/DWC pipe/ masonary Open Duct/ cable tray/ open in air etc. as requred. 4 core, 25 sq.mm. Aluminium Armoured
246	Providing, fixing, testing and commissioning of control panel for Terrace Booster pumps .Incoming: MCCB 35A 1 set of Phase indicating lamps, 1 set of 35A Al bus bars, 1No Ammeter, 1No Voltmeter with phase selector switch Feeder for Booster Pumps - 1 No. 1 No. 32A TP MCCB without releases. DOL starter with over load relay, single phase preventor and indicating lamps with ON/OFF push buttons. 2No. Automanual selector switch. Suitable for booster pumps
247	Providing & fixing of heavy class M.S. pipes conforming to IS: 1239/3589 complete with fittings including trenching and refilling etc. (external work) including all fittings and accessories like tees, elbows, flanged joints, rubber insertion, nuts, bolts or cutting and welding joints. Providing thrust block at distance specified as per specifications. (Pipe shall be provided with anti corrosive protective treatment with coal tar/asphalt tape confirming to IS: 10221 standard complete as per specification). All work complete as per specification and as directed by Engineer-In-Charge. (All the fitting i.e. tee /elbow etc. for Valve connections etc. will be flanged joints)( Heavy duty pipe 80 mm dia
248	Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : (The Welding shall not be done for piping less than 50 mm dia.) 80 mm dia
249	Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required : Single headed Stainless Steel (Internal)
250	Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required. 80 mm dia
251	Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required : 80 mm dia
252	Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange. 80 mm dia
253	Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required : Stainless Steel (Grade 304)
254	Providing and fixing in position the industrial type pressure gauges with gun metal / brass valves complete as required
255	Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585, 20 mm nominal internal dia gun metal globe valve & nozzle.Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket.40 m
256	Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required : Stainless Steel (Grade 304)
257	Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required : 2 way - 100 mm dia M.S. Pipe
258	Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and paintingwith synthetic enamel paint of approved shade as required.
259	Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required.
260	Providing & fixing heavy duty double flanged flexicon rubber expansion joint (suitable for system test pressure) of standard length as per manufacturers specs including rubber gaskets, flanges, nuts, bolts and washers complete as required. 80 mm dia
261	Supplying and fixing fire hose cabinet fabricated from 16 gauge M.S. Sheet with single or double glazed front door (with 4 mm thick glass) and locking arrangement, painted fire red with stove enamelled paint \\"FIRE HOSE\\" written on front including necessary supports approximate size. a)750mm x 600mm x 250mm deep. (Internal only for hose reel)
262	Supplying and fixing of Fire Man's axe with heavy insulated rubber as per standard conforming to IS 926.
263	Providing and fixing of carbon-di-oxide type fire extinguishers consisting of welded M.S. cylinderical body, squeeze lever discharge valve fitted with pressure indicating guase ingernal discharge tube 30 cms long high pressure discharge hose, discharge nozzle, suspension bracket conforming ro IS:15683 finished externally with re enamel paint and fixed to wall with brackets complete with internal charge. 4.5kg capacity cylinder
264	Providing and fixing ABC Powder type fire extinguishers consisting of welded M.S. cylinderical body, squeeze lever discharge valve fitted with pressure indicating guase internal discharge tube 30 cms long high pressure discharge hose, discharge nozzle, suspension bracket conforming to IS:15683 finished externally with re enamel paint and fixed to wall with brackets complete with inernal charge. Dry Chemical Powder ABC type of 6 Kg as per IS:15683
265	Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit with modular switch modular plate suitable GI box and earthing the point with 1.5 sq.mm FRLS / HFFR PVC insulated copper conductor single core cable etc.as required. Group C
266	Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point (without independent switch etc.) with 1.5 sq. mm FRLS / HFFR PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS / HFFR PVC insulated copper conductor single core cable etc. as required. Group C
267	Wiring for power plug points with 2 x 4 sq.mm. FRLS / HFFR PVC insulated, Cu. Conductor, single core cable in surface/ recessed medium class PVC conduit along with 1 No. 4 sq.mm. FRLS / HFFR PVC insulated copper conductor single core cable for loop earthing as required.
268	Wiring for light plug points / power plug points with 4 x 4 sq.mm. FRLS / HFFR PVC insulated, Cu. Conductor, single core cable in surface/ recessed medium class PVC conduit along with 2 Nos. 4 sq.mm. FRLS / HFFR PVC insulated copper conductor single core cable for loop earthing as required.
269	Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS / HFFR PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 x 1.5 sq.mm. + 1 x 1.5 sq.mm. earth wire.
270	Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS / HFFR PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required, 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire
271	Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS / HFFR PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required, 2 X 4 sq. mm + 1 X 4 sq. mm earth wire
272	Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS / HFFR PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required, 4 X 6 sq. mm + 2 X 6 sq. mm earth wire
273	Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS / HFFR PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required, 4 X 10 sq. mm + 2 X 6 sq. mm earth wire
274	Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS / HFFR PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required, 4 X 16 sq. mm + 2 X 6 sq. mm earth wire
275	Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.
276	Supplying and fixing call bell/ buzzer suitable for single phase, 230 volts, complete as required.
277	Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.
278	Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixing 2 nos. 3 pin 5/6 A modular socket outlet and 2 nos. 5/6 A modular switch, connections etc. as required. (For light plugs to be used in non-residential buildings).
279	Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 A & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.
280	Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet (near equipment point) and 25 A modular SP MCB, “C” curve (at accessible point) including connections, painting etc. as required.
281	Supplying and fixing 30 A, 415 V, TPN Industrial type socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 30 A, “C” curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.
282	Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.
283	Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.
284	Numbering of ceiling fan/ exhaust fan/ fluorescent fittings as required.
285	Suppliying and fixing following modular switch/socket on the existing modular plate & switch box including connections but excluding modular plate etc.as required. TV antenna socket outlet
286	Suppling and drawing co-axial TV cable RG-6 grade , 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC shealth in the existing surface/recessed steel/ PVC conduit as required.
287	Supply, Installation, Testing & Commissioning of CAT 6A UTP LSZH Cable, 23 AWG solid copper conductors in accordance to TIA/EIA 568 C.2 (Category 6a) & ISO/IEC 11801 2nd ed(Class Ea), UL Approved, tested @500 Mhz, with HDPE insulation of individual conductor and over all Dia of 7.2 mm for Connectivity of Hub room to End Point. Grey Color.
288	Supply, Installation, Testing & Commissioning of CAT 6A UTP Universal (both tool & toolless) information outlet (I/O) in accordance with ANSI TIA 568 C.2, IEC 60603-7-4 2nd Edition, ISO/IEC TR 11801-9901-2014, ROHS Compliant. The I/O should have minimum 750 mating cycle and 200 insertion cycle and UL approved,for Data, Voice, & Wi-Fi at user end.
289	Supply, Installation, Testing & Commissioning of loaded 24 port CAT 6A UTP, loaded Transparent shutter jack panel, 1U height, UL-94V-0, Black with cable support bar, clear label marks and earthing plug for CAT6A cable termination at rack end.
290	Supply, Installation, Testing & Commissioning of CAT 6A UTP, LSZH Patch Cord as per ANSI/TIA/EIA 568C.2 and UL 94-V-0, ROHS Compliant, patch cord 1 Mtr for rack side switch to jack panel connectivity.
291	Supply, Installation, Testing & Commissioning of CAT 6A UTP, LSZH Patch Cord as per ANSI/TIA/EIA 568C.2 and UL 94-V-0, ROHS Compliant, patch cord 2 Mtr for rack side switch to end user connectivity.
292	Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required. 1 or 2 Module (75mmX75mm)
293	Supply, Installation, Testing & Commissioning of 15 U wall mount rack with fans , 2 cable managers , satationary shelf , 2 Nos. of hardware pkts. & 5Nos. 6/16A sockets PDU also complete as required.
294	Supplying and fixing of following sizes of Medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 25 mm
295	Providing and fixing following rating and breaking capacity and pole MCCB in existing cubicle panel board including drilling holes in the cubical panel, making connections etc. as required. (for VTPN DB) 100/63 A,36KA,FP MCCB
296	Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator), 8 Way (4+24), Double Door
297	Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) 8 way Double door (4 + 24)
298	Supplying and fixing Cable End Box (Loose Wire Box) suitable for following triple pole and neutral, sheet steel, MCB distribution board, 415 Volts, on surface / recess, complete with testing and commissioning etc.as required. For 8 way, Double door TPN MCBDB
299	Supplying and fixing Cable End Box (Loose Wire Box) suitable for triple pole and neutral, sheet steel, Vertical MCB distribution board, 415 Volts, on surface/ recess, complete with testing and commissioning etc. as required.
300	Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, \\"C\\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole
301	Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, \\"C\\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Double pole
302	Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, \\"C\\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Triple pole
303	Supplying and fixing of following rating, four pole 415 V , Isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 Amp
304	Supplying and fixing of following rating, four pole 415 V , Isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63 Amp
305	Supplying and fixing of following rating double pole (Single phase and neutral) 240 volts, residual current circuit breaker (RCCB), having a current sensivity current 30 miliampere in the existing MCB DB complete with connections, testing & commissioning etc. as required. 40 Amps
306	Supplying and fixing of following rating double pole (Single phase and neutral) 240 volts, residual current circuit breaker (RCCB), having a current sensivity current 30 miliampere in the existing MCB DB complete with connections, testing & commissioning etc. as required. 63 Amp
307	LED Down lighter (SMD Type) (System lumen efficacy ≥120<135lm/Watt)Supplying, installation, Testing & Commissioning of LED Recessed/surface Down lighter (Round/ square/ Rectangular) SMD type of following body material with PMMA and prismatic diffuser and construction as per IS : 10322 with driver as per the requirement with Driver efficiency >85%, Operating voltage AC 140-270 Volt, frequency 50/60 hz, Operating temp range -5 0C to 40 0C centigrade, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10%,P. F.≥0.95,Rating) , IP20, CRI >80, UGR(Unified GlareRating) <19Flicker free (flicker should be below 5 %), life time (LED, Driver & electrical circuitry), life time of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends, CCT 3000°K / 4000°K / 5700°K /6500°K (As per ANSI Bin), SDCM(Standard Deviation Color Matching) <3, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard. Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing Complete in all respect i/c external connections with 1.5 sq mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy ≥120 <135 lm/Watt output . LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted.. Shape size and CCT shall be as approved by Engineer-in- Charge as per requirement. (Thermal management: heat sink of aluminium housing such that LED junction temperature shall not rise above 90°C) Powder coated die cast /Extruded aluminium Body including trim. 8-10WATT
308	LED Down lighter (SMD Type) (System lumen efficacy ≥120<135lm/Watt)Supplying, installation, Testing & Commissioning of LED Recessed/surface Down lighter (Round/ square/ Rectangular) SMD type of following body material with PMMA and prismatic diffuser and construction as per IS : 10322 with driver as per the requirement with Driver efficiency >85%, Operating voltage AC 140-270 Volt, frequency 50/60 hz, Operating temp range -5 0C to 40 0C centigrade, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10%,P. F.≥0.95,Rating) , IP20, CRI >80, UGR(Unified GlareRating) <19Flicker free (flicker should be below 5 %), life time (LED, Driver & electrical circuitry), life time of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends, CCT 3000°K / 4000°K / 5700°K /6500°K (As per ANSI Bin), SDCM(Standard Deviation Color Matching) <3, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard. Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing Complete in all respect i/c external connections with 1.5 sq mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy ≥120 <135 lm/Watt output . LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted.. Shape size and CCT shall be as approved by Engineer-in- Charge as per requirement. (Thermal management: heat sink of aluminium housing such that LED junction temperature shall not rise above 90°C) Powder coated die cast /Extruded aluminium Body including trim. 12-15 WATT
309	LED Down lighter (SMD Type) (System lumen efficacy ≥120<135lm/Watt)Supplying, installation, Testing & Commissioning of LED Recessed/surface Down lighter (Round/ square/ Rectangular) SMD type of following body material with PMMA and prismatic diffuser and construction as per IS : 10322 with driver as per the requirement with Driver efficiency >85%, Operating voltage AC 140-270 Volt, frequency 50/60 hz, Operating temp range -5 0C to 40 0C centigrade, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10%,P. F.≥0.95,Rating) , IP20, CRI >80, UGR(Unified GlareRating) <19Flicker free (flicker should be below 5 %), life time (LED, Driver & electrical circuitry), life time of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends, CCT 3000°K / 4000°K / 5700°K /6500°K (As per ANSI Bin), SDCM(Standard Deviation Color Matching) <3, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard. Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing Complete in all respect i/c external connections with 1.5 sq mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy ≥120 <135 lm/Watt output . LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted.. Shape size and CCT shall be as approved by Engineer-in- Charge as per requirement. (Thermal management: heat sink of aluminium housing such that LED junction temperature shall not rise above 90°C) Powder coated die cast /Extruded aluminium Body including trim. 18 WATT
310	LED Down lighter (SMD Type) (System lumen efficacy ≥120<135lm/Watt)Supplying, installation, Testing & Commissioning of LED Recessed/surface Down lighter (Round/ square/ Rectangular) SMD type of following body material with PMMA and prismatic diffuser and construction as per IS : 10322 with driver as per the requirement with Driver efficiency >85%, Operating voltage AC 140-270 Volt, frequency 50/60 hz, Operating temp range -5 0C to 40 0C centigrade, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10%,P. F.≥0.95,Rating) , IP20, CRI >80, UGR(Unified GlareRating) <19Flicker free (flicker should be below 5 %), life time (LED, Driver & electrical circuitry), life time of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends, CCT 3000°K / 4000°K / 5700°K /6500°K (As per ANSI Bin), SDCM(Standard Deviation Color Matching) <3, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard. Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing Complete in all respect i/c external connections with 1.5 sq mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy ≥120 <135 lm/Watt output . LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted.. Shape size and CCT shall be as approved by Engineer-in- Charge as per requirement. (Thermal management: heat sink of aluminium housing such that LED junction temperature shall not rise above 90°C) Powder coated die cast /Extruded aluminium Body including trim. 30WATT
311	LED Batten light (System lumen efficacy ≥105 <120lm/Watt) Supplying, Installation, Testing & Commissioning of LED surface mounted Batten light of following body material and construction as per IS : 10322 with driver (Replaceable) as per the requirement with Driver efficiency >85%, Operating voltage AC 140- 270 Volt, frequency 50/60 hz, Operating temp range -5 °C to 40 °C, internal surge protection of 2.5 KV with Short & Open circuit protection, THD < 10%, P. F.≥0.95, IP20, CRI >80, Flicker free, (flicker should be below 5 %), life time (LED, Driver & electrical circuitry), of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends, CCT 3000°K / 4000°K / 5700°K /6500°K (As per ANSI Bin), SDCM(Standard Deviation Colour Matching) <3, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard. Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. complete in all respect i/c external connections with 1.5 sq mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy ≥105 <120 lm/Watt output . LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in- Charge as per requirement. (Thermal management: heat sink of aluminium housing such that LED junction temperature shall not rise above 90°C) 18-22 WATT
312	LED Batten light (System lumen efficacy ≥105 <120lm/Watt) Supplying, Installation, Testing & Commissioning of LED surface mounted Batten light of following body material and construction as per IS : 10322 with driver (Replaceable) as per the requirement with Driver efficiency >85%, Operating voltage AC 140- 270 Volt, frequency 50/60 hz, Operating temp range -5 °C to 40 °C, internal surge protection of 2.5 KV with Short & Open circuit protection, THD < 10%, P. F.≥0.95, IP20, CRI >80, Flicker free, (flicker should be below 5 %), life time (LED, Driver & electrical circuitry), of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends, CCT 3000°K / 4000°K / 5700°K /6500°K (As per ANSI Bin), SDCM(Standard Deviation Colour Matching) <3, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard. Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. complete in all respect i/c external connections with 1.5 sq mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy ≥105 <120 lm/Watt output . LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in- Charge as per requirement. (Thermal management: heat sink of aluminium housing such that LED junction temperature shall not rise above 90°C) 40watt
313	Supplying and fixing single wall mounted 9/10 watt (2ft long) LED type batten fitting complete with electronic driver and LED etcdirectly on wall/ceiling including connections with 1.5sq.mm FRPVC insulated copper conductor and earthing the body etc. as required.
314	Supply, installastion, testing & commissioning of LED Bulkhead with a nominal system lumen output of 600 lumens and a minimum system efficacy of 100 lm/W. The luminaire shall have a rated system lifetime of 50,000 burning hours at L70. The luminaire should have a color temperature of 6500K and CRI > 70. The luminaire shall meet IP66 rating and IK 09 rating with THD < 20% and PF > 0.9. The luminaire housing should made of High pressure die cast Aluminium with polycarbonate front diffuser. The total power consumption should not exceed 10W (including driver). Including 3 core 1.5 sq.mm FRLS PVC insulated and PVC sheathed copper conductor cable and earthing etc. Up to suitable point complete as required.
315	Supply, Installation, Testing and Commissioning of metallic, wired ,analog, hybrid staff calling bell LED type indicator, individual unit with call buttons ranges from 24-30 nos indicator, wall mounted deign as per architectural drawings and direction of Engineer-in-charge.
316	Supply, Installation, Testing and Commissioning of ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. metal( Aluminium alloy) blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, steel/Al body Power Factor not less than 0.9, Service Value (CM/M/W) minimum as below, 350 RPM (tolerance as per IS : 374-2019), THD (Total Harmonic Distortion) less than 10%, suitable for operation with regulator for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 0C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC supply, Ceiling Fan compliant to IS 374:2019 fan i/c external connections with 1.5 sq.mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required. 1200 MM Ceiling fan
317	Supply, Installation, Testing and Commissioning of ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. metal( Aluminium alloy) blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, steel/Al body Power Factor not less than 0.9, Service Value (CM/M/W) minimum as below, 350 RPM (tolerance as per IS : 374-2019), THD (Total Harmonic Distortion) less than 10%, suitable for operation with regulator for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 0C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC supply, Ceiling Fan compliant to IS 374:2019 fan i/c external connections with 1.5 sq.mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required. 1400 MM Ceiling fan
318	Supply and installation of 450 mm 230V AC exhaust fan in the existing opening including making good the damage including connection, testing, commissioning etc as required
319	Supply and installation of 300mm, 230V AC wall /cabin fan including fixing the bracket, making connection, testing, commissioning etc as required.
320	Supplying, Installation, Testing and commissioning of Passive Infrared (PIR) technology based occupancy sensor having high performance, non regulating programmable type, suitable for connected load upto 10Amp , for mounting height up to 3 meter and for 5 m diameter coverage area along with necessary fixing arrangements i/c programming at site etc. complete as required
321	Design, Manufacturing, Supply, Installation, Testing & Commissioning of cubicle type totally enclosed free standing / Wall mounted type moisture, dust and vermin proof compartmentlized Floor Distribution Panel made out of 2.0 mm thick of Main members & front cover 1.6 mm thick CRCA sheet complete with internal wiring with suitable size wires / cable, interconnection, painting complete as per specification & drawing. y. The MCCB rating up to 250A shall have thermal megnatic based adjustable over current, short circuit protection and above 250A MCCB shall have microprocessor based adjustable over current, short circuit, earth fault protection. All Main Distribution board / Sub Distribution board / Meter boards which are located inside various blocks shall be partially Type Tested assemblies (PTTA) as per conforming to IEC-61439-1 The Moulded Case Circuit Breaker shall have a minimum fault breaking capacity (Ics) of not less than 35 KA & 25KA RMS for one second at 415 volts for MDB / SDB respectively. MCCB‘s above 63A should be provided with Copper & procader terminals. Incomer of Meter Board shall have a minimum short circuit breaking capacity (Ics) of 25KA for one second at 415volt.INCOMING, 1 No. 200 Amp FP,36KA, Moulded Case Circuit Breaker1 Set of phase indicating lamps with MCB.1 Set of ON/OFF indicating lamps with MCB.1 No.Digital Voltmeter with Voltmeter selector switch.1 No.Digital Ammeter with Ammeter selector switch.1 NO. SPD with Protection fuse.BUSBAR, 250 Amp TPN aluminium busbar with coloured heat shrinkable sleeve.OUTGOINGS, 1 No125 Amp FP,25 KA, Moulded Case Circuit Breaker3 No100 Amp FP,25 KA, Moulded Case Circuit Breaker2 No 63 Amp FP,25 KA, Moulded Case Circuit Breaker1 Nos. 63 Amp DP Miniature Circuit Breaker.Panel described as above
322	Ground floor PanelINCOMING1 No. 125 Amp FP,25KA, Moulded Case Circuit Breaker1 Set of phase indicating lamps with MCB.1 Set of ON/OFF indicating lamps with MCB.1 No.Digital Voltmeter with Voltmeter selector switch.1 No.Digital Ammeter with Ammeter selector switch.BUSBAR, 150 Amp TPN aluminium busbar with coloured heat shrinkable sleeve. OUTGOINGS, 4 Nos. 63 Amp FP Miniature Circuit Breaker.3 Nos. 40 Amp FP Miniature Circuit Breaker.Panel described as above
323	First floor Panel, INCOMING1 No. 100 Amp FP,25KA, Moulded Case Circuit Breaker,1 Set of phase indicating lamps with MCB.1 Set of ON/OFF indicating lamps with MCB.1 No.Digital Voltmeter with Voltmeter selector switch.1 No.Digital Ammeter with Ammeter selector switch.BUSBAR, 120 Amp TPN aluminium busbar with coloured heat shrinkable sleeve.OUTGOINGS, 4 Nos. 63 Amp FP Miniature Circuit Breaker.3 Nos. 40 Amp FP Miniature Circuit Breaker.Panel described as above
324	Second floor Panel, INCOMING1 No. 100 Amp FP,25KA, Moulded Case Circuit Breaker1 Set of phase indicating lamps with MCB.1 Set of ON/OFF indicating lamps with MCB.1 No.Digital Voltmeter with Voltmeter selector switch.1 No.Digital Ammeter with Ammeter selector switch.BUSBAR, 120 Amp TPN aluminium busbar with coloured heat shrinkable sleeve. OUTGOINGS, 4 Nos. 63 Amp FP Miniature Circuit Breaker.3 Nos. 40 Amp FP Miniature Circuit Breaker.Panel described as above
325	Earthing with GI earth Pipe 4.5 mtr long 40 mm dia including accesories and providing masonary enclosure with cover plate having locking arrangement of 2.7 mtr long etc with charcoal/cock and salt as required
326	Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required.
327	Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required.
328	Providing and fixing GI tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required. (For horizontal run)
329	Providing and fixing GI tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required. (For vertical run)
330	Fixing of lightning conductor finial (single prong) with base plate including holes etc. complete as required.
331	Jointing copper / G.I. tape (with another copper/ G I tape, base of the finial or any other metallic object) by riveting / nut bolting/ sweating and soldering etc as required.
332	Providing and laying G.I. tape 32 mm X 6 mm from earth electrode directly in ground as required.
333	Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm long, with 4 nos. of G.I. bolts, nuts, chuck nuts and spring washers etc. complete as required.
334	Supply and erection of 5 Mtr Galvanized as per BS EN ISO 1461) octagonal pole with base plate 200x200x12mm, top 70 mm and bottom 130 mm of 3 mm thick sheet suitable for maximum wind speed up to 160 Km/ Hr. including foundation bolts and foundation with M 20 grade RCC and FE 415 grade approved by pole manufacturer) GI base plate G.I. anchor plate etc. as required each pole shall be supplied with a junction. looping box complete with 6Amp. 10 KA \\" C\\" curve S.P. MCB screw less din mounting connectors suitable links end locks including supplying and fixing of 1 Mtr. long single arm hot dipped galvanized bracket suitable for street light fittings and supplying and drawing of 3 x 1.5 Sq mm FRLS copper conductor single core cable from junction box to luminaire complete including termination with copper lugs as required.
335	Supplying installation of LED street light fitting Nominal 35 watt IP 66 Protection, single piece pressure die cast aluminum housing with heat resistant toughened glass on existing pole bracket including correction with 3×1.5 sq.mm PVC copper wire including testing and commissioning complete as required.
336	Supply, Installation, Testing & commissioning of IP65 8W LED Bollard with dark grey polyester coated rust proof Die cast Aluminium housing, with symmetrical dual optics and PC diffuser The luminaire shall have initial system lumen of 400lm with System efficacy of >50Lumen/W. The LED shall have a CCT of 3000K with LEDs shall be LM80 Compliant with TM21 report for life of 25000 hrs at 35 Deg C. and CRI 80 with beam angle of 360°.The Fixture shall have IP65 potted driver with THD<25%, PF>0.9, with operating volatge range of 180-270V. The fixture shall comply with IS 10322 part 5/Sec 1 1987 and LM79 LM80 reports are tested and certified by NABL accredited Lab.
337	Supplying following 1.1kV grade, heavy duty XLPE insulated PVC Sheathed Aluminum Conductor FRLS type armoured cables suitable for 415V, 50Hz, AC system, with inner and outer PVC sheath, outer sheath provided with FRLS insulation, galvanised steel armouring (round or flat as mentioned) and with all components as mentioned in BOQ, specifications and schedule, complete etc. as required. 3.5 core, 95 sq.mm.
338	Supplying following 1.1kV grade, heavy duty XLPE insulated PVC Sheathed Aluminum Conductor FRLS type armoured cables suitable for 415V, 50Hz, AC system, with inner and outer PVC sheath, outer sheath provided with FRLS insulation, galvanised steel armouring (round or flat as mentioned) and with all components as mentioned in BOQ, specifications and schedule, complete etc. as required. 3.5 core, 50 sq.mm.
339	Supplying following 1.1kV grade, heavy duty XLPE insulated PVC Sheathed Aluminum Conductor FRLS type armoured cables suitable for 415V, 50Hz, AC system, with inner and outer PVC sheath, outer sheath provided with FRLS insulation, galvanised steel armouring (round or flat as mentioned) and with all components as mentioned in BOQ, specifications and schedule, complete etc. as required. 4 core, 10 sq.mm.
340	Supplying following 1.1kV grade, heavy duty XLPE insulated PVC Sheathed Aluminum Conductor FRLS type armoured cables suitable for 415V, 50Hz, AC system, with inner and outer PVC sheath, outer sheath provided with FRLS insulation, galvanised steel armouring (round or flat as mentioned) and with all components as mentioned in BOQ, specifications and schedule, complete etc. as required. 4 core, 25 sq.mm.
341	Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc.as required. Upto 35 sq. mm (clamped with cable tie)
342	Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray/surface as required. Upto 35 sq. mm (clamped with cable tie)
343	Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray/surface as required. Above 35 sq. mm and upto 95 sq. mm (clamped with cable tie)
344	Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required. 3½ X 95 sq. mm (45mm)
345	Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required. 3½ X 50 sq. mm (35mm)
346	Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required. 4 X 25 sq. mm (28mm)
347	Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required. 4 X 10 sq. mm (25mm) (used for 4 x 6 sq. mm & 4 x 4 sq. mm cable)
348	Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.inclunding Bends & TEE etc. 100 mm width x 50 mm depth x 1.6 mm thickness
349	Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge. 2.6.1 All kinds of soil
350	Excavating trenches of required width for pipes, cables, etc, including excavation for sockets, depth upto 1.5 m, including getting out the excavated materials, returning the soil as required in layers not exceeding 20 cm in depth, including consolidating each deposited layers by ramming, watering etc., stacking serviceable material for measurements and disposal of unserviceable material as directed, within a lead of 50 m : Ordinary rock : Pipes, cables etc. exceeding 80 mm dia but not exceeding 300 mm dia
351	Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)
352	Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 5.1.2 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)
353	Centering and shuttering including strutting, propping etc. and removal of form for : Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.
354	Centering and shuttering including strutting, propping etc. and removal of form for :Suspended floors, roofs, landings, balconies and access platform
355	Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.. Thermo-Mechanically Treated bars of grade Fe-500D or more.
356	Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110 mm
357	Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Bend 87.5° 110 mm bend
358	Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 300 mm dia. R.C.C. pipe
359	Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4coarse sand) C.I. cover with frame (light duty) 455x610 mm internaldimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 Fine sand : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1cement : 5 fine sand : 10 graded stone aggregate 40 mm nominalsize), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design: Inside dimensions 600x 850 mm and 45 cm deep for pipe line with three or more inlets : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
360	Extra for depth beyond 45 cm of brick masonry chamber 19.31.3 For 600x850 mm size 19.31.3.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
361	Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, upto 90 metre depth below ground level. Rocky strata including Boulders 300 mm dia
362	Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 200 mm nominal size dia
363	Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.
364	Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.
365	Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer -incharge.
366	Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge.
367	Supplying & laying of drainage composite for use behind walls, between two different fills, alongside drains of road, below concrete lining of canals etc. Geocomposite for planar drainage, realized by thermobonding a draining core in extruded monofilaments with two filtering nonwoven geotextiles that may also be working as separation or protecting layers. The draining three dimensional core will have a “W” configuration as longitudinal parallel channels. Minimum thickness to be 7.2mm, with two filtering UV stabilized polypropylene nonwoven geotextile of minimum thickness of 0.75mm characteristic opening size (090) of 110 micron and tensile strength of 8.0 KN/m that will be working as separation or protecting layer, geocomposite having in plane flow capacity of 2.1 L / (m.s) at hydraulic gradient of 1.0 & 20 kPa pressure and tensile strength of 18 kN/m , with mass per unit area of 740 gsm, supplied in the form of roll for easy transportation to site of work as per detailed specification all complete as per directions of Engineer in charge.
368	Supply, installation, testing & commissioning of SS Screen with SS Frame with suitable lifting arrangement to block the in organics like bottles, glass, polythenes etc. Type: Bar Screen; Size: 500 X 600mm Make: SS 304 Fabricated
369	Supplying and placing of 3+1+1 seater sofa with Upholstery Material : Syn Leather, Thickness : 1 mm ,Frame Material : Pine Wood, Moisture content : 10 - 12 % , Thickness of Plywood used : 12 mm & 18 mm .Seat Foam Material : Conjugated hollow fiber (Recron), Back Foam :Material : Conjugated hollow fiber. Polyurethane foam having density = 45 +/- 2 Kg./cm3. The hardness of the P.U. foam = 16 - 20 Kgs. on Hampden m/c. for 25% compression of the foam. The complete moulded backrest assembly(Recron) Facia : MDF coated with lacquer, Webbing Material : Nylon, Thickness : 2 mm. Legs : Material : PVC with 4 mm bush Width: 2190mm Depth: 990mm Height: 965mm.(shop Drawings to be provided by contractor . The design, shade and make will be approved by Engineer in charge.) Make- Godrej Interio, Durian, Damro, Leatherlite.
370	P/F Sofa having flexing-back lounge seating system standing on beam with side frame assemblies. Having Connecting Beam assembly which is a fabricated assembly made by welding MS. square pipe 6.0 cm. x 6.0 cm. x 10 BG. thick. to 0.5cm. thick HR. Steel plate on each side for fixing the moulded side frame assembly. The connecting beam assembly is black powder coated. The seat rest assembly consists of a fabricated inner-frame assembly insitu-moulded with Polyurethane foam having density = 45 +/- 2 Kg./cm3. The hardness of the P.U. foam = 23 - 27 Kgs. on Hampden m/c. for 25% compression of the foam. The complete moulded seat rest assembly is covered with a replaceable fabric upholstery cover. SEAT SIZE: 52.0cm.(W) x 50.0cm.(D) x 6.0cm.(T) Approx. The backrest assembly is flexing type and consists of a fabricated inner-frame assembly insitu-moulded with Polyurethane foam having density = 45 +/- 2 Kg./cm3. The hardness of the P.U. foam = 16 - 20 Kgs. on Hampden m/c. for 25% compression of the foam. The complete moulded backrest assembly is covered with a replaceable fabric upholsterycover BACK SIZE: 52.0cm.(W) x 57.0cm.(H) x 12.0cm.(T) Approx. The side frameassembly, which forms the armrest assembly, is fitted to the two ends of the connecting beam asssy. to form the leg-cum-armrest assembly. It consists of a fabricated inner-frame assembly insitu-moulded with Polyurethane foam having density = 45 +/-2 Kg./cm3. The hardness of the P.U. foam = 16 - 20 Kgs. on Hampden m/c. for 25% compression of the foam. The complete moulded side frame assembly is covered with a replaceable fabric upholstery cover. SIDEFRAME (ARMREST) SIZE: 63.0cm.(D) x 58.0cm.(H) x 12.0cm.(T) Approx. The adjustable glide is injection moulded in black ABS and is used for level adjustment of the sofa on uneven floor surface. It is fitted to the side frame assembly. 3 Seater Sofa
371	P/F Sofa having flexing-back lounge seating system standing on beam with side frame assemblies. Having Connecting Beam assembly which is a fabricated assembly made by welding MS. square pipe 6.0 cm. x 6.0 cm. x 10 BG. thick. to 0.5cm. thick HR. Steel plate on each side for fixing the moulded side frame assembly. The connecting beam assembly is black powder coated. The seat rest assembly consists of a fabricated inner-frame assembly insitu-moulded with Polyurethane foam having density = 45 +/- 2 Kg./cm3. The hardness of the P.U. foam = 23 - 27 Kgs. on Hampden m/c. for 25% compression of the foam. The complete moulded seat rest assembly is covered with a replaceable fabric upholstery cover. SEAT SIZE: 52.0cm.(W) x 50.0cm.(D) x 6.0cm.(T) Approx. The backrest assembly is flexing type and consists of a fabricated inner-frame assembly insitu-moulded with Polyurethane foam having density = 45 +/- 2 Kg./cm3. The hardness of the P.U. foam = 16 - 20 Kgs. on Hampden m/c. for 25% compression of the foam. The complete moulded backrest assembly is covered with a replaceable fabric upholsterycover BACK SIZE: 52.0cm.(W) x 57.0cm.(H) x 12.0cm.(T) Approx. The side frameassembly, which forms the armrest assembly, is fitted to the two ends of the connecting beam asssy. to form the leg-cum-armrest assembly. It consists of a fabricated inner-frame assembly insitu-moulded with Polyurethane foam having density = 45 +/-2 Kg./cm3. The hardness of the P.U. foam = 16 - 20 Kgs. on Hampden m/c. for 25% compression of the foam. The complete moulded side frame assembly is covered with a replaceable fabric upholstery cover. SIDEFRAME (ARMREST) SIZE: 63.0cm.(D) x 58.0cm.(H) x 12.0cm.(T) Approx. The adjustable glide is injection moulded in black ABS and is used for level adjustment of the sofa on uneven floor surface. It is fitted to the side frame assembly. 2 Seater Sofa
372	Supplying and placing of corner table: Dimensions W x H x D (cm) 50 x 42.9 x 50 1. Understructure: Legs, top wooden frame & bottom tie members are made out of first quality rubber wood without knots & defects on all faces. Bottom tray is made of 1.2mm thick MS sheet. Metal brackets are used for assembly purpose. Top: 8mm thick toughened glass. Construction: Knock-down assembly. Finish: Bloom_corner table is in colour finish option , Black Wooden members are PU painted with hardness-2H.Metal components are powder coated.Bottom MS metal tray is having floral pattern laser-cut. Top glass is having sand blasted floral pattern on bottom surface. Hardware: Knock-down assembly with high quality standard hardware like screws, metalinserts, wooden dowel, plastic leg bush etc.. (shop Drawings to be provided by contractor & approved by Engineer in charge.)
373	Supplying and placing of centre table of Dimensions W x H x D (cm) 100.1 x 42.9 x 59.9 1 cm Understructure: Legs, top wooden frame & bottom tie members are made out of first quality rubber wood without knots & defects on all faces. Bottom tray is made of 1.2mm thick MS sheet. Metal brackets are used for assembly purpose. Top: 8mm thick toughened glass.. Construction: Knock-down assembly.Finish: Bloom_coffee table is in colour finish option -ÿ Option : Walnut finish Wooden members are PU painted with hardness-2H.Metal components are powder coated.Bottom MS metal tray is having floral pattern laser-cut.Top glass is having sand blasted floral pattern on bottom surface. Hardware: Knock-down assembly with high quality standard hardware like screws, metal inserts, wooden dowel, plastic leg bush etc.. (shop Drawings to be provided by contractor & approved by Engineer in charge.)
374	Supplying and placing of modern chair of Dimensions W x H x D (cm) 60 x 88.4 x 33.3 Finish Color: as per requirement., Weight:21.00 kgs Upholstery Material: Leatherette (shop Drawings to be provided by contractor & approved by Engineer in charge.)
375	Supplying and placing of bed:Dimensions W x H x D:(cm)189.9 - 193.5 x 105.8 x 202.3 Finish Color: as per requirement, Delivery Condition: Knock Down Warranty:1-Year Warranty recommended Mattress Size: Depth : 198.1 cm (78\\"), Width : 182.9 (72\\"), Minimum Thickness : 10.2 cm (4\\") Primary Material:WoodPrimary Material Subtype:Engineered Wood Make- godrej Electra King Bed or equivalent As per approval of Engineer in charge.) (shop Drawings to be provided by contractor & approved by Engineer in charge.)
376	P/F SIDE TABLE Providing and supplying table made up of 19/12mm thick marine plywood, 4mm thick veneer finished top with melamine polish/imported Melamine coating including supports, drawers etc. complete as directed of approved shape & design as per drawing. all as directed. Bed side table with drawer - 450X500X135mm high fixed on bed headboard- 12mm thick marine plywood @ top, bottom & sides finished with 4mm thick veneer with melamine polish/imported Melamine coating, Drawer with 12mm thick marineplywood @ bottom & sides internal finished with approved 1mm thick laminate. etc. complete as per drawing. (Basic rate of Veneer of Rs. 2000/- Sq.mt.) (Shop drawings to be given by the contractor and design to be approved by Engineer-in-charge)
377	Supplying and placing of dresser: Overall Size:Width - 900.0 mm Depth -600mm Height - 201.3 to 300 mm.Material:Body panels are made of 18 mm thick Prelaminated Particle Board All the exposed edges are edge banded with 2 mm thick PVC edge banding. Mirror Door & Drower fronts are made of 18 mm thick is made of Prelaminated particle Board.Body back is made of 18 mm thick prelaminated particle board.Hardware:The high quality hardware used like Hinges, wooden dowels is of Make Hettich.Construction:Knock Down construction.Packets: dresser —3 packets Finish:18 mm thick Front drawer is of 18 mm PVC membrane pressed board (shop Drawings to be provided by contractor & approved by Engineer in charge.)
378	Providing, placing and supplying of bed of Dimensions W x H x D (cm) 189.9 x 113 x 202.3 Finish Color: as per requirement, Condition: Knock Down Warranty: 1-Year Warranty Recommended Mattress Size:Depth : 198.1 cm (78\\"), Width : 182.9 (72\\"), Minimum Thickness : 10.2 cm (4\\") or size od king size double bed, One of the key features of this bed is the storage compartments located on both sides. These storage boxes can be easily accessed by lifting the mattress platform on either side. The boxes offer convenient storage space for bedding, pillows, blankets, or other items, Engineered Wood Make Godrej Squadro or equivalent (shop Drawings to be provided by contractor & approved by Engineer in charge.)
379	Supplying and placing of mattress: The combination of different foam layers improves weight distribution, corrects sleeping posture, and lessens pressure points. The mattress is built with an airflow feature.Available in thickness of 12.5cm and 15cm.PU Foam Quilt: Adds soft cushioning and aesthetic appeal to the mattress. Convoluted Foam: Convoluted foam promotes airflow and breathability in the mattress with its egg-crate design, reducing the chance of heat retention during sleep. Hard Foam: The hard base ensures even weight distribution and prevents long-term sagging of the mattress.Bonded Foam: Bonded foam maintains mattress stability, evenly distributing weight to prevent sagging. PU Foam Quilt: Adds soft cushioning and aesthetic appeal to the mattress.Recommended Mattress Size:Depth : 198.1 cm (78\\"), Width : 182.9 (72\\"), Minimum Thickness : 10.2 cm (4\\") , Make Godrej or equivalent (shop Drawings to be provided by contractor & approved by Engineer in charge.)
380	Providing, placing and supplying of dresser: Overall Size:Width -1200.0 mm Depth -600mm Height - 900.0 mm.Material:Body panels are made of 18 mm thick Prelaminated Particle Board All the exposed edges are edge banded with 2 mm thick PVC edge banding. Mirror Door & Drower fronts are made of 18 mm thick is made of Prelaminated particle Board.Body back is made of 18 mm thick prelaminated particle board.Hardware:The high quality hardware used like Hinges, wooden dowels is of Make Hettich.Construction:Knock Down ruction.Packets:DRESSER —3 packets Finish:18 mm thick Prelaminated Particle Board, Shade.as per requirement. Front drawer is of 18 mm PVC membrane pressed board.(shop Drawings to be provided by contractor & approved by Engineer in charge.)
381	Looking mirror of full length 6 feet 60 cm wide floor standing with hd 5 mm glass with frame brass 5 cm wide all around \\"clear reflection scratch hardness 5 MOHs and explosion-proof film for safety..(shop Drawings to be provided by contractor & approved by Engineer in charge.)
382	brass cap stand wall mounted for 25 caps holding. With circular mirror at centre. ITBP brass logo at centre middle .(shop Drawings to be provided by contractor & approved by Engineer in charge.)
383	Pillow: Pillow dimensions: supplying good quality micro foam/ dobby fabric based soft sleeping pillow of size: 430 × 690mm of appropriate fill thickness Make Godrej Muna Chair. CPL or equivalent As per approval of Engineer in charge.)
384	BAR STOOL These Classic Cafeteria Chairs are a perfect blend of style and comfort. It is with unique design, light weight and durable in nature. Easy to maintain and clean. Frame is available with 3 different models with different height. It is designed with environmental criteria stipulated by EMS and OHSAS guidelines.Frame (Bar stool) : The Frame is made out of 12 mm thickness MS rod conforming to IS – 7887. Frame is welded by Co2 welding process for uniform finish. Chair total height measures 1090 mm & Seat height measures 750mm from the floor. Surface finish : Frame is powder coated to provide an attractive finish. Coating thickness of 40 to 60 microns is maintained. Powder coated products are durable & reduce the risk of scratches, chipping, abrasions, corrosion, fading and other wear issues.Seat & Back shell : Shell is made of GF polypropylene with 9mm thickness. Molded Shell is fixed to the frame with hardware. Seat measures 400 mm in depth. It is designed ergonomically to provide comfort to the user. The shell profile is designed with water fall to provide necessary comfort in popliteal region. Leg Bushes : Bushes molded with PC and PVC.FASTNERS: High quality metal screws and tension fasteners are used conforming to Hardness 35-44 HRC.Colors available & Packing : Shell is available with White, Black, Red, Grey and green colors with multiples of 4 nos. Minimum order quantity is 4 nos. in same color.Center Table - Supplying of Center Table of size (L) 1220mm X (W) 610mm X (H) 410mm. (minor variations permissible in sizes on plus side and upto 5mm on minus side). The table top shall be made with 19mm thick commercial ply & 1mm thick decorative laminate/veneer.The four crafted/ square/ curved legs of size approx. 75mm x 50mm shall be made of any kind of solid wood. The side and bottom frames not less shall be made of any kind of solid wood and with bottom shelf to be completely finished' with glossy/ matte melamine polish. Aestheic look/ shade as well as pattern of center table will be selected from catalogue to be provided by the firm. Indicative Image for Concept of table is attached..design as per approal of Engineer in charge.)
385	Supplying , Installation, Testing and Commissioning of Air Cooled Hi Wall split type Air conditioners complete with Indoor unit(IDU), Out door unit (ODU), surface / concealed copper Refrigerant piping with insulation (closed cell elastomeric nitrile rubber tubular pipe section) upto 3 Mtr (IDU to ODU), copper power cable upto 3.5 Mtr (IDU to ODU) i/c drain pipe R-32/R-410/ R-407 Green Refrigerant, wireless Remote control, suitable for working between 180- 260V with low & high voltage cutoff and 50 hz ,1 phase AC supply capable of performing cooling, dehumidification, air circulation of following capacity with Scroll / rotary compressor. The system shall be able to deliver 100% of the rated capacity upto 42 0C. Min 5 year Original Equipment Manufacturer (OEM) warranty both compressor and Printed Circuit Board (PCB). Must comply : Electrical cable IS 694 or IS 9968 temperature sensing control IS /International Electrotechnical Commission (IEC) 60730, hermetic compressor IS 10617, heat exchanger IS 11329,capacitor IS 2993 and motor IS 12615. Complete as per CPWD specification and IS : 1391 Part II 2023. The system shall be able to operate up to 50 0C (out door ambient temperature).Inverter Type - Cooling only 2.0 TR with 5 Star BEE Rating
386	Providing and fixing of soft drawn copper refregerent pipe i/c accessories,bracing with necessary supports as required (for beyond 4 mtrs of split AC units) Of suitable of above item and pdg insulation with nitrile rubber in performed tubular suction (suction line)(2.0 TR) -6.4 mm dia
387	Providing and fixing of soft drawn copper refregerent pipe i/c accessories,bracing with necessary supports as required (for beyond 4 mtrs of split AC units) Of suitable of above item and pdg insulation with nitrile rubber in performed tubular suction (Liquid line)(2.0 TR)-12.7 mm dia
388	Providing and fixing factory fabricated floor/wall mounted type MS angle iron frame suitable for installing of split AC outdoor unit material etc as required.
389	Supply & Fixing of key tag outlet mechanical on exisitng M.S. Box and modular Plate complete as required.
390	Supply & Fixing of Touch Panel type 'DND'/ 'MMR'/'Bell' switches complete with internal/external unit on exisitng M.S. Box as required.
391	FOUR DOOR REFRGERATOR 500 ltr. Double walled PUF insulated body , the unit to have 4nos doors fitted with gasket. The unit to have 8nos shelves to be fitted on adjustable channel. The unit to have automatic temperature controller. Temperature range shall be between 0-5 degree C.1250X750X2000
392	CHEST FREEZER 100 LTRS 1. An upright ultra-low temperature freezer.2. The instrument should provide precise, ultra-low temperature environments for cold storageof scientific materials, from -50 °C to -86 °C at 32 °C maximum ambient operating temperature.3. The instrument should have two compressors.4. The minimum capacity of the freezer should be 400 L.5. There should be five Compartments with four adjustable height SS shelves.6. Power consumption should be about 525 watts/ 12.60Kwh per day7. There should be a large LED display.8. Pull down Time should be around 4 hours.9. There should be password protection for temp. & alarm set-points.10. The indicator lamps on the control panel should provide warnings of power loss, systemfailure, exceeding High/Low temperature set points, low battery voltage, and filter blockage.
393	S.S RACK 5-TIER. Complete s.s construction , shelves to be made of 20swg s.s sheet. The rack to have 5nos shelves to be placed at equal distance. Shelves to be duly welded with s.s vertical pipes with adjustable feet.900X450X1800
394	TWO BURNER COOKING RANGE. Top to be made of 16swg 304 grade ss sheet. Frame work to be made of MS angle frame work mounted on s.s vertical pipes with adjustable feet. The unit to have 1nos under shelf. The range to have 2nos pan support of approx size - 15x15 inches. 1100X600X850+150
395	WORK TABLE WITH 2-UNDERSHELF. Top to be made of 16swg 304 grade s.s sheet. Frame work to be made of duly painted MS angle frame work mounted on s.s vertical pipes with adjustable feet. The table will have 2 nos undershelf . 1950X600X850
396	Providing and fixing in position Reception/BAR counters as per design made with overall length of 8'-6\\" to 9'-0\\" (2591 mm to 2743mm ) and width of 762mm. The counter to have multiple heights with customer height being 1065 mm, reception working top at 762mm and intermediate storage box to be at 915mm as per details. The counter to have provision for 2 occupants. The item includes one drawer unit per occupant with 2 drawers and 1 shuttered storage. Drawers to be made from 12mm comm ply with 19mm com board facade. The drawers and storage along with the inside of tables to be finished with 0.8mm laminate from inside. The work top at 762mm to be finished with 18mm Solid Acrylic surface with moulding on leading edge. The customer top & front to have 12mm solid acrylic surface finish of approved colour (DuPont-Corian make) pasted and shaped with thermoforming over 19mm comm board as per details. The outer area of table to be finished in combination of SS perforated sheet of approved design and 6 mm thk Lacquered glass of approved shade and design. The item includes one key board tray running on telescopic channel , 1 CMelamine trolley, 1 foot rest per occupant. Item includes all hardware such as Self closing hinges, telescopic channels, locks, SS handles etc. complete to the satisfaction of Engineer-in-charge
397	Providing, Fixing, Supplying & installation of 55\\" LED TV screen with USB Ports, 4 HDMI Ports, Ethernet Port, PC Input VGA Port with 2 Speakers, minimum 50 W Output, Dolby Digital sound. Preferred Make: Sony Bravia KDL-50W800D 126cm (50 inches) Full HD 3D Android LED TV. (For1 no. VIP room & flat 103 drawing room). Note: Cost to include Providing, drawing, connecting and testing of Television cable, Electrolytic grade solid annealed high conductivity copper conductor, gas injected physical polyethylene foam insulated, wrapped with aluminium tape and aluminium alloy wire braided, jelly flooded and PVC jacketing in black colour (Compatible to DTHTV signal), in 25 mm MS/PVC conduit from television outlet box to the junction box /splitter / subscribe rord welling unit/ Dish antenna as required.
398	Providing, Fixing, Supplying & installation of 32\\" LED TV screen with USB Ports, 4 HDMI Ports, Ethernet Port, PC Input VGA Port with 2 Speakers, minimum 20 W Output, Dolby Digital sound.Preferred make: Sony BRAVIA Sony Bravia KLV-40R562C 101.6 cm (40 inches) Full HD LED TV. (For 5 no. bed rooms.)Note: Cost to include Providing, drawing, connecting and testing of Television cable, Electrolytic grade solid annealed high conductivity copper conductor, gas injected physical polyethylene foam insulated, wrapped with aluminium tape and aluminium alloy wire braided, jelly flooded and PVC jacketing in black colour (Compatible to DTHTV signal), in 25 mm MS/PVC conduit from television outlet box to the junction box /splitter / subscribe rord welling unit/ Dish antenna as required.
399	Supply ,installation ,testing and commissioning of kitchen wall mounted chimany ,Material and Construction Grade: High-duty commercial canopies use 304 or 202 series Stainless Steel for superior heat, rust, and fire resistance.Thickness: Usually ranging between 16 to 20 gauge (1.2 to 1.5 mm), ensuring durability against heavy grease and daily cleaning.2. Ventilation and SuctionAirflow Capacity: Needs to be robust, typically between 1200 to 2500 m³/hr, scaled according to the length of your cooking range.Blower Motor: Heavy-duty, direct-drive or belt-driven centrifugal exhaust fans, often ranging from 1 to 5 HP depending on the duct length. DuctworkMaterial: Galvanized Iron (GI) or Stainless Steel, designed to be completely airtight.Size: Standard duct diameters are often around 450 × 450 mm, properly sized to maintain the required static pressure.5. Hood DimensionsCoverage: The hood should overhang the cooking equipment by at least 6 to 12 inches on all open sides complete in all respect with outlet arrangements as required
400	Supply, Installation,Testing and Commissioning of LED RGB/RGBW Linear Wall Washer luminaire for Facade lighting with aluminium extruded housing,offollowing wattage.Luminaire shall be capable of producing dynamic color changing light with 16 million colors by DMX/Ethernet based control.The beam angle of the fitting Shall be narrow,medium, wide or asymmetric as per the requirement. Luminaire shall be complete with driver and capable of operating at line voltage without anys eparate power supply from 100to270 V AC,50Hz,power factor> 0.9.Fixture shall be suitable to operate at ambient temperature range of- 10°Cto+50 °C and shall be IP65 and IK 06 rated. Life time should be at least L70:50000 burning hours at 50°C. Luminaire shall be conforming to BIS and shall be complete with all necessary accessories required for proper working of fixture including weather proof connection cables, water proof connectors etc. as required. 80 W
401	Supplying, Installation, Testing and Commissioning of Stainless steel 304 gr. Comet effect nozzle with compatible Digitally controlled pump to produce desirable effects with 40 mm dia and 20 mm orifice nozzle etc. complete as required as per direction given by engineer in charge
402	Supplying, Installation, Testing and Commissioning of fixing of Suction Screen stainer made of ABS to be fitted in suction to protect the pump from enrty of external materials etc. complete as required.
403	Supplying, Installation, Testing and Commissioning of 100 mm Dia Debris Collection Strainer in Stainless steel 304 gr etc. complete as reqd.
404	Supplying, Installation, Testing and Commissioning of three phase openwell ISI Marked submersible pump set of 7.5 H.P. capacity suitable for operation on 415V(+-10%), 3- phase AC supply compatible for operations on dynamic variable frequency / speed having IP 68 Protection including providing required no's of heavy duty M.S clamps made of flat iron and suitable size top cover made of suitable thick MS sheet as required. and making of flexible IP68 cable connections etc. complete as required.
405	Supplying, Installation, Testing and Commissioning of fixing of following dia. Gun metal gate valve (Screwed type) on the existing pipeline, including testing & Commissioning etc. complete as required..
406	Supplying, Installation, Testing and Commissioning of underwater Luminaries surface mounted RGB LED spot light 6 x 3W with IP 68 protection, SS/ aluminum dia casting body with power coated paint, soft rubber gasket along with 2 years free replacement guaranty etc. complete as required..
407	Supplying, Installation, Testing and Commissioning of water proof (IP 68) power supply unit of not less than 200W i/c connection along with 2 years free replacement guaranty etc. complete as required.
408	Supplying, Installation, Testing and Commissioning of RGB controller with remote Kit wattage not less than 200 watt i/c connection along with 2 years free replacement guaranty etc. complete as required.
409	Supplying, Installation, Testing and Commissioning of Signal Amplifier of RGB signal as require i/c connection along with 2 years free replacement guaranty etc. complete as required.
410	Supplying, Installation, Testing and Commissioning of fixing of Power Supply/SMPS for suitable to run LED Lights, Body-Metal input Power-220 V AC/ Output Power-12 V DC etc. complete as required.
411	Supplying & fixing PVC insulated PVC sheathed copper conductor submersible flat cable ISI Marked in existing metal/ HDPE / PVC/ pipe/ in bore well/ in sump including fixing the cable to GI/HDPE pipe with suitable cable tags of following sizes etc. complete as required. 3 Core 10 Sq mm Flat Cable Please Enable Macros to View BoQ information

Tender Documents

SR No	FileName	File Description
1	Click here to download tender document	Tender Documents
2	Click here to download tender document	Tender Documents
3	Click here to download tender document	Tender Documents
4	Click here to download tender document	Tender Documents

Also Visit

Tenders

Uttarakhand Tenders

Construction Tenders

Building Construction Tenders

Building Work Tenders

Disclaimer

We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.

Top

Tender For Construction Of Combined Building Of Gos Mess For Eastern Frontier And Shq (Lko) At Darogakhera, Eastern Frontier, Itbp, Lucknow, Darogakheda Lucknow-Uttarakhand

Tender Documents

Disclaimer

About Us

Services

Browse Tenders

For Sales Inquiry

Tender For Construction Of Combined Building Of Gos Mess For Eastern Frontier And Shq (Lko) At Darogakhera, Eastern Frontier, Itbp, Lucknow, Darogakheda Lucknow-Uttarakhand

Tender Documents

Disclaimer

OTP Verification

About Us

Services

Browse Tenders

For Sales Inquiry

Connect With Us