Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | M&L for earth work in excavation by mechanical means (Hydraulic excavator) means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5m, in all kind of soil complete all as specified and as directed. |
| 2 | M&L for earth work in excavation by mechanical means (Hydraulic excavator) means over areas (exceeding 1.5 m but n exc 3.0m in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5m, in all kind of soil complete all as specified and as directed. |
| 3 | M&L for treating the bottom and sides in contact with foundation at the rate of 5 litres of emulsion per square metre o surface complete all as specified and directed. |
| 4 | M&L for treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured) complete all as specified and directed. |
| 5 | M&L for antitermite treatment by treating the top surface of filed earth at the rate of 5 litres of emulsion per square metre of surface etc complete all as specified and as directed. |
| 6 | M&L for Treating the soil under plinth protection at the rate of 5 litre of emulsion per square metre of surface area complete all as specified and directed. |
| 7 | M&L for treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall complete all as specified and directed. |
| 8 | M & L for PCC 1:4:8, type D-2, using (40mm graded stone aggregate) as foundation, filling and mass concrete complete all as specified and as directed. |
| 9 | Returning, filling in, including, spreading, levelling, watering and well ramming in layers not exc. 25 cm deep as in soil complete as specified. |
| 10 | M&L for use and waste of form work to sides of concrete, foundation, footings & plinth beams and similar works with rough finished surfaces of concrete in flat complete all as specified and as directed. |
| 11 | M&L for use and waste of formwork to sides of columns with fair finished surfaces of concrete in square, rectangular or polygonal complete all as specified and as directed. |
| 12 | M&L for use and waste of formwork to side and soffit of roof beam, lintel band etc. complete all as specified and directed . |
| 13 | M&L for use and waste of formwork to chullah hoods, chajjas, troughs & similar items including edges with rough, finished surfaces of concrete in flat complete all as specified and directed . |
| 14 | M & L for brick work fly ash, sub-class ‘B’ bricks, straight or curved on plan exc. 6 m mean radius laid dry complete all as specified and directed . |
| 15 | M & L for brick work with old size, sub-class ‘B’ bricks, straight or curved on plan to any radius in half brick walls built in CM 1:4, complete all as specified. |
| 16 | M & L for RCC (Design Mix ) M-25 (using 20mm graded stone aggregate),in foundation, including rafts, footings, foundation, beams, plinth beams bases for column etc. complete all as specified and as directed. |
| 17 | M & L for RCC (Design Mix ) M- 25(using 20mm graded stone aggregate), in columns, pillars, piers posts & struts etc. complete all as specified and as directed. |
| 18 | M & L for RCC (Design Mix ) M- 25(using 20mm graded stone aggregate), in beams, lintel over 1.5m span complete all as specified and as directed. |
| 19 | M & L for RCC (Design Mix ) M-25 (using 20mm graded stone aggregate)as in Chajjas complete all as specified and as directed. |
| 20 | S&F mild steel TMT bars 10mm dia and over , cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed |
| 21 | S&F mild steel TMT bars 8mm dia and over as in stirrups spacer and binder, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed. |
| 22 | S & F sand filling under floors or in foundation incl watering and consolidation complete all as specified and as directed. |
| 23 | Material and labour for polythene film black 150 micron laid in road over sand cushioning all as specified and as directed. |
| 24 | M & L for brick work with old size, sub-class ‘B’ bricks, straight or curved on plan exc. 6 m mean radius built in cement mortar (1:6), complete all as specified and directed . |
| 25 | M & L for rendering 15mm thick plaster in CM (1:6) on fair faces of brick work or concrete Surfaces complete all as specified and as directed. |
| 26 | M & L for rendering 15mm thick plaster in CM (1:4) on fair faces of brick work or concrete surfaces complete all as specified and as directed. |
| 27 | Supply only integral water proofing compound complete all as specified and as directed. |
| 28 | M & L for PCC 1:4:8 type D2 (using 40 mm graded stone aggregate) 75mm thick as in sub base, flooring etc complete all as specified and as directed. |
| 29 | M & L for PCC 1:2:4 type B2 (using 40 mm graded stone aggregate) 100 thick as in sub base, flooring etc complete all as specified and as directed. |
| 30 | M & L for 30mm thick PCC 1:2:4, type B-1, using (20mm graded stone aggregate) as in flooring etc. finished concrete surface even and smooth without using extra cement, complete all as specified and as directed. |
| 31 | M&L Machine cut kota stone slab flooring 20-25mm thick over and including 20mm thick screed in CM(1:6) laid & jointed with grey cement slurry mixed with pigment to match the shade of the slab including making 2nos grove and bull nosing in steps including rubbing & polishing complete all as specified and directed. |
| 32 | M&L for 18 to 22 mm thick kota stone slab as in skirting, riser of steps and pillars over and including 15mm thick rendering in cement mortar (1:4) including rubbing grinding and mirror polishing complete all as specified and as directed. |
| 33 | M&L for vitrified ceramic tiles 10mm thick (square/rectangular) not exc 0.36Sqm, in floors etc. set and jointed in white or coloured cement to match in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed or bedding layer of cement mortar (1:6) complete all as specified and as directed. |
| 34 | M&L for vitrified ceramic tiles 10mm thick (square/rectangular) not exc 0.36Sqm, in floors etc. set and jointed in white or coloured cement to match on vertical surface of wall such as dados , skirting etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick screed bed or bedding layer of cement mortar (1:3) complete all as specified and as directed. |
| 35 | M&L for coloured glazed ceramic tiles 350 x 250x 7/450mm x 300mm x 7mm thick as in vertical surface set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in cement mortar (1:4) for fixing wall tiles complete all as specified and as directed. |
| 36 | M&L for Non skid coloured ceramic tiles 7 to 8mm thick (Square/rectangular) area of each tile exc 0.11 Sqm but not exc 0.18Sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 20mm thick screed bed or bedding layer in CM (1:6) for laying floor finishes complete all as specified and as directed. |
| 37 | M&L for granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement and admixture of pigment to match the shade of granite stone including grinding and polishing complete in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 20mm thick screed bed or bedding layer in CM (1:6) complete all as specified and as directed. |
| 38 | M & L for 75mm thick PCC 1:3:6 , type C-1 using (20mm graded stone aggregate) as in plinth protection finished even & smooth without using extra cement making 10mm wide joints at every 3m interval and at every corner, filled with mixture of bitumen and sand (1:1) complete all as specified and as directed. |
| 39 | S&F anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified and as directed. |
| 40 | S & F anodised aluminium frame for doors, windows, ventilators, with one or more rebates incl. joining cleat for fixing etc. complete all as specified and as directed. |
| 41 | S&F anodised aluminium door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading screws etc. complete all as specified and as directed. |
| 42 | S&F anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified and as directed. |
| 43 | S&F anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with CP brass/ stainless steel screws @ 200mm centre to centre, including cutting grill to proper opening size for fixing and operation of handles and fixing with approved anodised aluminium standard section around the opening, complete all as specified and as directed. |
| 44 | S&F mortice lock brass 4 levers vertical type size 100mm complete all as specified and as directed. |
| 45 | S&F Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and as directed. |
| 46 | M&L for 4mm thick Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane in aluminium window shutters, complete all as specified and as directed. |
| 47 | M&L for 4mm thick Sheet glass, ordinary quality and glazing with oil putty in square exc 0.5 sq. m in each pane in aluminium window shutters, complete all as specified and as directed. |
| 48 | M&L for 4mm thick figured glass, pin head type and glazing in square exc n. 0.5 sq. m in each pane in aluminium ventilator shutters, complete all as specified and as directed. |
| 49 | M&L for 4.8mm thick Sheet glass, ordinary quality and glazing with oil putty in square exc 0.5 sq. m in each pane in aluminium window shutters, complete all as specified. |
| 50 | S&F for Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and as directed. |
| 51 | S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and as directed. |
| 52 | S&F butt hinges 75mm long cold rolled medium weight complete all as specified and as directed. |
| 53 | S&F for 150mm long aluminium handles, cast type, anodised complete all as specified and as directed. |
| 54 | S&F for 150mm long aluminium anodised barrel tower bolts of extruded section complete all as specified and as directed. |
| 55 | S&F vitreous china wash down water closet pan (EWC), (pedestal pattern) white with & including PVC white colour seat cover fixed with mild steel CP hinging device, complete all as specified and as directed. |
| 56 | S&F vitreous china urinal, bowl type (back or corner wall type) complete including and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, fixing automatic flushing cistern with flush pipe, grating and union for discharge pipe. ( Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe), complete all as specified and as directed. |
| 57 | S&F 10 litre capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including bracketscomplete all as specified and as directed. |
| 58 | S & F steel rolling shutters, without ball bearing, as specified including top cover anchoring rod, hasp and staple and one shop S&F in repair steel rolling shutters 1.25mm thick gear operated type with bevel gear box and crank handle including top cover, anchoring rod, hasp staple and one coat of primer erected complete including required PCC for hold fast and fixing complete. Coat of primer erected in position as indicated, complete with gear operated type with level gear box and crank handle complete all as specified and as directed. |
| 59 | Material and labour for preparation of new steel or iron surfaces over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed. |
| 60 | S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self-tapping screws with neoprene and EPDM washers complete all as specified and as directed. |
| 61 | S & F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self-tapping screws complete all as specified and as directed. |
| 62 | Supply and Fix,0.63 mm thick Plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 complete all as specified and as directed |
| 63 | Supply and fix rolled mild steel Fe 410 -W (Gde- E- 250) quality- A as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates complete all as specified and as directed. |
| 64 | Supply and fix for mild steel work such as band, clamps, for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; handmade sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles, straps, ties etc. and similar works, fabrication for steel sections conforming to Fe-290 (Grade E-165) including necessary welding, bending cold or hot, drilling holes for bolts in any shape or size as indicated complete all as specified and as directed. |
| 65 | Supply and fix rolled mild steel Fe 290 (Gde-E-165) , in plates (Plain or chequered), channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted , bolted or welded attachment complete all as specified and as directed. |
| 66 | Mild steel screw bolts of 16 to 20 mm diameter of shank (machine made) with hexagonal or square heads at one end and screwed the other, each screwed end to be fitted with washers and one hexagonal or square nut, not exceeding 5cm long complete all as specified and as directed |
| 67 | Mild steel screw bolts of 16 to 20 mm diameter of shank (machine made) with hexagonal or square heads at one end and screwed the other, each screwed end to be fitted with washers and one hexagonal or square nut, exceeding 15cm but n. exe 22.5 cm long complete all as specified and as directed |
| 68 | Excavation in trenches n.exc 1.5 m wide and n.exc 1.5 m in depth for laying of cable/foundation of pole and getting out in soft/loose soil complete all as specified and as directed. |
| 69 | Excavation in trenches n.exc 1.5 m wide and n.exc 1.5 m in depth for foundation, , shafts, wells, cesspits, manholes, pier holes etc not exc 10 Sqm on plan and getting out in soft/loose soil complete all as specified and as directed. |
| 70 | M & L 15mm bore GI pipe medium grade with all fittings and fixed complete to walls and ceilings or laid in floor complete all as specified and as directed. |
| 71 | M & L 20mm bore GI pipe medium grade with all fittings and fixed complete to walls and ceilings or laid in floor complete all as specified and as directed. |
| 72 | S & F 15mm bore pillar taps, cast copper alloy, with capstan heads, chromium plated screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly-nuts, screwed for iron pipe complete all as specified and as directed. |
| 73 | S & F PVC connections 15 mm size with PTMT nuts of length 450 mm complete all as specified and as directed. |
| 74 | S&F vitreous china wash basin, white flat back, size of 550mmx400mm including cutting for and pinning in ends of brackets or erecting stand and including 32mm dia waste pipe and bracket including waste coupling of size 32/40 of PTMT, complete all as specified and as directed. |
| 75 | S & F in repair 15mm stop valve/ angular stop cock fancy type chromium plated alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipes or union complete all as specified and as directed. |
| 76 | S & F in repair 15mm bore bib taps, chromium plated with CP flange screwed down, screwed for iron pipe or for brass ferrule complete all as specified and as directed. |
| 77 | S & F 600mmx450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and as directed. |
| 78 | S & F PTMT towel rail 450mm long complete all as specified and as directed. Make - Prayag Cat No 199, CERA, Esso, parryware and equivalent complete all as specified and as directed. |
| 79 | S & F brass chromium plated shower rose 125mm size with shower arm 225mm long with flange including fixing to steel pipe or union all as specified and as directed Make- Prayag CERA, Essco, parryware and equivalent. |
| 80 | S & F flexible/collapsible PVC waste pipe 32/40x800mm long for kitchen sink/ wash basin complete all as specified and directed Make Prayag cat No 3272, CERA, Essco, Hindware, parryware and equivalent complete all as specified and as directed. |
| 81 | S & F Grating doom 125 mm dia PTMT with/without hole complete all as specified and directed Make Prayag cat no 112, Hindware, parryware and equivalent complete all as specified and as directed. |
| 82 | S & F 500 Litres capacity rotational moulded poly ethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part – I with & including PVC Float valve 20mm bore, Tank cover, wash out and overflow pipe necessary tank nipples, , complete all as specified and as directed. |
| 83 | S & F 20mm bore ball/float valves, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed, complete all as specified and directed. Make Prayag cat No 152, Cera, Essco, Hindware, parryware and equivalent complete all as specified and as directed. |
| 84 | S & F Gun metal Gate Valve 20mm bore with iron wheel head, screwed both end for iron pipe complete all as specified and as directed. |
| 85 | S & F Health Faucet CP brass with 1m long Stainless steel connection pipe and fixed to stop cock/ angle cock complete all as specified and as directed. Make \\"Prayag-BEA-95S Hindware, parryware and equivalent complete all as specified and as directed. |
| 86 | S&F 50mm bore low density poly ethylene pipes (LDPE) of pressure rating 6kg/sq cm fixed to walls, ceiling or in floors etc. complete all as specified and as directed. |
| 87 | S&F 75mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints, fixed to walls, complete all as specified and as directed. |
| 88 | S&F 110mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints, fixed to walls, complete all as specified and as directed. |
| 89 | S&F 75mm bore PVC (SWR) bends any radius with access door complete all as specified and as directed. |
| 90 | S&F 110mm bore PVC (SWR) bends any radius with access door complete all as specified and as directed. |
| 91 | S&F PVC (SWR) floor trap 75mm plain with grating including jointing with solvent cement complete all as specified and as directed. |
| 92 | M&L for concealed point wiring with two single core FRLSH PVC insulated unsheathed multistranded copper conductor cable of size 1.5 sqmm 1100 volts grade with one single core PVC insulated unsheathed multistranded copper conductor cable of size 1.5 sqmm 1100 volts grade green in colour as earth continuity conductor connected to common earth dolly drawn through in and including PVC conduit (medium grade) of adequate size but not less than 20 mm ISI marked with all fittings and accessories including sunk/pressed mild steel terminal boxes with outer/inner plates for mounting switches, socket, regulator etc for one light point controlled by one 5 Amps one way switch complete all as specified and as directed. Notes: (i) Cost of metal flush box and cover plate shall be included in the item. |
| 93 | All as per item No 93 here-in before but for one 3 pin 5 Amps switch socket outlet on independent board complete all as specified and as directed. |
| 94 | All as per item No.93 here-in-before but for power point wiring with 2.5 sqmm FRLSH PVC insulated, unsheathed, copper conductor, stranded 1100 volt grade cable and 2.5 Sqmm FRLC PVC insulated , unsheathed, copper conductor, stranded 1100 volt grade cable as earth continuity conductor for one 3/5 pin 15 Amps switch socket outlet on independent board complete all as specified and as directed. |
| 95 | M&L for point wiring with two single core FRLSH PVC insulated unsheathed multistranded copper conductor cable of size 1.5 sqmm 1100 volts grade with one single core PVC insulated unsheathed multistranded copper conductor cable of size 1.5 sqmm 1100 volts grade green in colour as earth continuity conductor connected to common earth dolly drawn through in and including stove enamelled steel conduit of adequate size ISI marked with all fittings and accessories, fixed to wall/ceiling including stove enamelled black steel junction box with cover plates for mounting switches, socket, regulator etc for one light point controlled by one 5 Amps one way switch complete all as specified and as directed. |
| 96 | All as per item No 96 here-in before but for each additional light point on the same switch circuit complete all as specified and as directed. |
| 97 | S&F switch piano flush type single pole one way, 5 Amp, AC,230 V complete all as specified and as directed. |
| 98 | s&f Switch flame proof rotary type with termination box in LM6, 16A, single pole 250V complete all as specified and as directed. |
| 99 | S&F ceiling rose, surface, Bakelite 65 x50 mm three terminals, AC, 230 Volts complete all as specified and as directed. |
| 100 | S&F Switch socket combination 2 in 1, 3 pin, 5 Amp flush type complete all as specified and as directed. |
| 101 | S&F Switch socket combination 2 in 1, 3 pin, 6 and 16 Amp flush type universal complete all as specified and as directed. |
| 102 | Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and as directed. |
| 103 | Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers complete all as specified and as directed. |
| 104 | Supply and fix stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc. as required complete all as specified and directed complete all as specified and as directed. |
| 105 | S&F 80mm dia, cast aluminium body LM6, flame proof, weather proof junction box 4way terminal with 4 number of 3/4 ET cable entry, protection type Ex-D, Zone I & Zone II, IP-55, Gas Group IIB, Temp class T6, complete all as specified and directed. MAKE- Sudhir Electrical Cat Part No. SAI/JB/1002 or equivalent model of make Balinga/Shyam/ crompton complete all as specified and as directed. |
| 106 | Supply and fixing LED light fitting mirror type with high output diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed. |
| 107 | Supply and fixing LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed. |
| 108 | Supply and fixing LED street light /security light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminium hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and as directed. |
| 109 | Supply and fixing LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed. |
| 110 | Supply and fixing LED light fitting 1x16 Watt flame proof, CMRI certified recommended for gas/ vapor group of IIA & IIIB, Zone 1 & 2 and IP 65 protection with die cast aluminium housing with heat resistant toughened glass with LED tube light fixtures driver, holders, connector etc. Complete with all accessories prewired and including connecting up with three core flexible copper conductor cable with suitable size complete all as specified and as directed. |
| 111 | S&F sheet metal enclosure for MCB DB’s SPN, Double Door 8 way, AC 415 volt, 200A rated bus bar including earth & neutral link, complete fixing accessories including disconnecting from electric circuit and taking out existing unserviceable SFUS, MCB DB SPN/ TPN or change over switches etc any number of ways including MCB etc removing materials from site and making good disturbed surfaces of floors/ walls/ celling etc complete all as specified and as directed. |
| 112 | S&F flame proof, weather proof enclosure for MCB Distribution Board, Single Phase and Neutral, with incoming & outgoing terminals chamber, bus bar chamber comprising of 02(Two) Nos. copper bus bars of suitable rating, separate MCB chambers suitable for accommodating 03 (Three) Nos. of 6-32 Amp. DP MCB 'C' curve, enclosure made of cast aluminium alloy LM6, weather proof IP65, finished inside and outside with light grey epoxy powder coating, including cable glands, terminals, hardware and mounting arrangement all as per Cat No. MCBDB/186 of Make “Sudhir” or equivalent Model of Make Balinga/ Shyam complete all as specified and directed. |
| 113 | Supply and fixing 6-32 Amp rating 240V, 10KA 'C' curve MCB SP complete all as specified and directed. |
| 114 | Supply and fixing 6-32 Amp rating 240V, 10KA 'C' curve MCB SPN complete all as specified and directed. |
| 115 | M&L for Earthing complete with galvanized steel earth plate electrode 600 x600 x 6 mm, buried directly and preferably vertically in ground (earth pit not less than 2.25 mtr deep below ground level) with top edge of the of plate not less than 1.5m below ground level connected to galvanized earth lead wire 4.0 mm dia by means of bolt, nut, check nut and washer of galvanized iron or steel earthing lead to be protected by galvanized iron pipe of 40 mm bore light grade and other end connected to earthing test point or main controlling switch as directed including providing funnel with 20 mm bore galvanized iron pipe medium grade for watering wire mess, charcoal or coke and common salt in alternative layers of 15cm (compacted thickness) all around the earth electrode, concrete earth pit in PCC(1:3:6) type CI, 50mm thick precast RCC (1:2:4) type B1cover slab reinforced with 8mm dia TMT bar @ 15cm C/C both ways and suitable handle made out of 10mm dia , including necessary excavation and earth work, returning filling and disposal of surplus soil to a distance n. exc 50m and testing on completion complete all as shown in electrical plate No 3 SSR Part-I complete all as specified and as directed. |
| 116 | Surface dressing n exc 15 cm deep and getting out in soft / loose soil complete all as specified and as directed. |
| 117 | Excavation in trenches not exc. 1.5 m wide and n.exc. 1.5m in depth and getting out in soft/loose soil complete all as specified and as directed |
| 118 | M&L for sand cushioning using dry silver sand for cable protection or under hard standing as or in foundation incl watering and consolidation complete all as specified and as directed. |
| 119 | Excavating over area not exceeding 1.5 m deep and getting out in soft / loose soil complete all as specified and as directed. |
| 120 | S & F sand filling under hard standing or in foundation incl watering and consolidation complete all as specified and as directed. |
| 121 | Removing excavated material exc. 50 m and depositing where directed complete all as specified and as directed. |
| 122 | S&F 32mm outer dia 3-layer PP-R concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc. complete all as specified & directed. Make- SFMC/ Finolex/ Supreme/ Prince/ Fusion or equivalent as approved complete all as specified and as directed. |
| 123 | All as per item No 125 above but 63mm outer dia complete all as specified & directed. Make- SFMC/ Finolex/ Supreme/ Prince/ Fusion or equivalent as approved complete all as specified and as directed. |
| 124 | S&F PP-R Gate valves (brass insert) for PPR pipe of size 63mm outer dia, complete all as specified and as directed. |
| 125 | All as per item No 127 above but for 32mm outer dia PP-R pipe complete all as specified and as directed. |
| 126 | Cutting existing GI pipe line and inserting tee including all accessories complete all as specified and as directed. |
| 127 | S&F 50 mm bore galvanized pipes light grade with all fittings and fixtures for cable protection complete all as specified and as directed. |
| 128 | Supply and laying sub class “B” bricks designation 75 as cable protection complete all as per specified and as directed. |
| 129 | M&L for Steel tubular swaged poles complete with cast iron base plate, finial taper plug, bolts, nuts & screw as specified type 410 SP-22 (8.5 meter long), complete all as specified and as directed. (Note: Excavation & PCC shall be measured and paid separately) |
| 130 | M&L for PCC (1:2:4) type B-2 (using 40mm graded crushed stone aggregates) as in foundations, fillings and mass concrete complete all as specified and as directed. |
| 131 | M&L for PCC (1:3:6) type C-2 (using 40mm graded crushed stone aggregates) for pole foundations, bed concrete n. exc 15cm depth in bottom of pit including necessary form work and forming neat finish surfaces complete all as specified and as directed. |
| 132 | M&L for PCC (1:2:4) Type C-2, (using 12.5 mm graded crushed stone aggregate) as in coping of pole including necessary form work and forming neat finish surfaces complete all as specified and as directed. |
| 133 | Supply and laying XLPE insulated, armoured heavy duty electric cable with aluminium conductor 1100 volt grade of cross sectional area 25 sqmm 3.5 core complete all as specified & as directed. Make- Finolex /Plaza/ Gloster. |
| 134 | M & L for brick work with old size burnt clay bricks of sub class B, straight or curved on plan exceeding 6m mean radius built in CM 1:4 complete all as specified and as directed. |
| 135 | M&L for providing PCC 1:2:4, type B-1 using 20 mm graded aggregate as in haunching/ benching in manholes. complete all as specified and as directed. |
| 136 | M&L, rendering 10 mm thick in cement mortar 1:4 on brick or concrete surface finished even and smooth without using extra cement complete all as specified and as directed. |
| 137 | M&L for Precast RCC 1:2:4, type B-1 using 20 mm graded aggregate set in CM 1:4 as in Manhole cover slabs complete all as specified and as directed. |
| 138 | Mild steel bars 6 mm to 8mm dia cut to length bent to shape required incl cranking, bending, hooping etc and binding with mild steel annealed wire not less than 0.9mm dia wire as in reinforcement complete all as specified and as directed. |
| 139 | M&L Concrete bed to drain pipes 150mm dia PCC 1:3:6 type C2 incl packing under and haunching against the sides of pipes after they are laid and tested in for 150mm dia pipe complete all as specified and as directed. |
| 140 | M&L for RCC NP2 150 mm dia sewage socket and spigot pipes laid in trenches and jointed and tested complete all as specified and as directed |
| 141 | M & L for cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required for 150 mm bore pipe line complete all as specified and as directed. |
| 142 | Material and labour for 200mm thick (spread thickness) soling in two layers of 100mm each with broken boulder or quarried stone interstices filled surfaces formed and rolled with 8-10 ton power roller and consolidated to reqd gradient and camber complete all as specified and as directed |
| 143 | M &L for 150mm thick (compacted thickness) WBM in 2 layers (each 75mm thick) with granite coarse aggregate 2 (63 to 40mm size) or of grading 3 (50 to 20mm size) , spread rolled and consolidated to required camber complete all as specified and as directed. |
| 144 | Supply and fixing polythene film, black 50 micron laid in floor complete all as specified and as directed. |
| 145 | M & L for cement concrete work in pavement /hard standing of flexural strength 40 kg/per square centimeter in field using 400 Kg of cement per cubic meter, thickness of concrete 25cm or less complete all as specified and as directed. |
| 146 | Forming construction joints 50mm deep and 10mm wide filled with sealing compound Grade 'A' all as specified and as directed |
| 147 | Forming construction (Dummy) joints 65mm deep and 10mm wide filled with sealing compound Grade 'A' all as specified and as directed |
| 148 | Material and labour for plain cement concrete (1:2:4) type B0 using 12.5mm graded aggregate in lintels upto 1.5m clear spans, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60cm height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating as directed including necessary formwork complete all as specified and as directed |
| 149 | Supply and fix, mild steel round bars, Fe 290, Grade E-165, cut to length, bend to shape required and hooking ends for fixing to chain link fencing complete all as specified and as directed. |
| 150 | Supply and fix, mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screw end to be fitted with washers and one hexagonal or square nut, diameter of shank 11 to 15mm, length of bolt exc 5 not exc 10cm long , complete all as specified and as directed |
| 151 | Supply and fix Rolled mild steel, conforming to fe 290 Gde E-165, in joist, channel angle or tee sections, fixed independently without connecting plates etc (cut to ordinary length indicated) complete all as specified and as directed |
| 152 | Supply and fix framed work as in gates of angle or other section with gusset plates, rails, braces, etc, complete drilled for fixing of steel sheeting or other covering , etc, to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging, also fastening and fixing complete Fe -410-S complete all as specified and as directed. |
| 153 | Supply only 3.15mm dia, galvanized steel wire chain link fencing 100mmx100mm mesh, including binding wire/line wire etc complete all as specified and as directed. |
| 154 | Fixing only 3.15mm dia, galvanized steel wire chain link fencing 100mmx100mm mesh, fixed to RCC fencing post with bolts etc including fixing of binding wire/line wire etc complete all as specified and directed . Note :- Supply only galvanized steel wire chain link fencing, mild steel round bars, mild steel flat, nuts bolts and washers will be measured and paid separately |
| 155 | Supply and fix galvanized 2 strand , steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacing and straining and fixing to any type of standard rails, straining bolts, including securing or tying at crossings with and provision of galvanized mild steel wire, staples or steel pin etc as directed (each line wire to be measured ) complete all as specified and directed |
| 156 | Material and labour for rendering 15mm thick cement plaster in cement mortar (1:4) on fair faces of brick work or concrete surface in wall finish even and smooth without using extra cement, complete all as specified and as directed |
| 157 | M & L Preparation of newly plastered wall surfaces and applying two coats of cement based paint over a coat of alkali resistant primer complete all as specified and as directed. |
| 158 | M & L for preparation of newly steel surfaces of any description over 10cm in width or girth and applying two coat of synthetic enamel paint over a coat of red oxide all as specified and as directed. |
| 159 | Material and labour for applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer on new steel and iron surface not exceeding 10cm in width or girth including preparation of surfaces complete all as specified and as directed |
| 160 | S&F for Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and as directed. |
| 161 | M&L for applying two coats of OBD on walls including preparation of new or previously untreated surfaces of wall with over a coat of alkali resistant primer paint complete all as specified and as directed. |
| 162 | M&L for Providing and applying plaster of paris putty of 1 mm thickness over plastered surface to prepare the surface even and smooth complete all as specified and as directed. |
| 163 | Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed. |
| 164 | Providing laying 40mm thick bitumen mastic wearing course (as per specifications) with industrial bitumen of grade 85/25 conforming to IS : 702 prepared by sing mastic cooker and laid to required level and slope including providing anti skid surface with bitumen precoated fine grained hard stone chipping of approved size at the rate of 0.005 cum per 10 Sqm and at approximates spacing of 10cm centre to centre in both directions, pressed into surface protruding 1mm to 4mm over mastic surface, including (considering bitumen using 10.2% as per MORTH specification) complete all as specified and as directed. |
| 165 | Bringing approved earth from outside MOD land and forming embankment including raising (or lowering) earth ,spreading in layers not exc 30cm thick, watering, ramming/rolling and consolidating with 8 to 10 ton power roller to achieve OMC dry density 95% and finished to required size and shape etc n exc 1.5m high from the base complete all as directed. |
| 166 | Forming embankment including raising (or lowering) earth using earth obtaind from excavation items of the schedeule,spreading in layers not exc 30cm thick, watering, ramming/rolling and consolidating with 8 to 10 ton power roller to achieve OMC dry density 95% and finished to required size and shape etc n exc 1.5m high from the base complete all as directed. |
| 167 | M&L Construction of valve pit chamber (Masonry) of size 45 cm x 45 cm x 45 cm depth (internal dimension) with sub class 'B' bricks one brick thick wall in cement mortar (1:4) 10mm thick plastering in cement mortar 1:4, PCC (1:4:8) type D-2 in foundation 150 mm thick, PCC (1:3:6) type C-1 as in bedding 10mm thick, PCC (1:2:4) type B-1 in coping 10mm thick including (40 x 40 x 6)mm MS angle iron frame, 3 mm thick MS cover plate with locking arrangement and painting to all steel surfaces with two coats of synthetic enamel paints over a coat of red oxide primer including surface preparation and necessary earth work and removal of spoil/rubbish upto a distance not exceeding 50 mtr and levelling complete all as specified and as directed. |
| 168 | Supply & Fixing MCCB FP, 100 Amps 16 KA 415 Volts, AC 50 Hz with sheet metal enclosure including making connection complete all as specified and as directed. |
| 169 | S&F cable junction box IP-66 protection, halogen free and weather proof for outdoor installation of street lights of size (200 x 160 x 98) mm complete with terminals complete all as specified and as directed. |
| 170 | Supply and fix 1x72 watt LED street light fitting made up of pressure die cast aluminium housing with toughened glass and high powered individual LEDs with secondary optics, constant current driver with in built protection against lightning over voltage & short circuit, IP-66 protection complete all as specified and as directed. Make:- Crompton cat No LSTP-72-CDL-M or equivalent in HPL/ Bajaj/ Havells. |
| 171 | Supply and fix decorative post top lantern light fitting for LED 40 Watt lamp for 3600 indirect light with IP 65 protection and resistant to impact and corrosion complete with all accessories as specified complete all as specified and as directed.Make:- Crompton LPTO-40-CDL-M or equivalent in HPL/ Bajaj/ Havells. |
| 172 | Supply and fix bracket made of GI pipe 40 mm bore light grade bend to shape not less than 1.5 mtr with 2 Nos of MS clamps fabricated out of MS flat of size 40x5 mm including nut, bolts, washers etc complete all as specified and as directed. |
| 173 | M&L On site Hume Pipe septic tank designed to carry sewage and sludge water, excavation in any type of soil, PCC 1:4:8 below foundation, Vent shaft, connection etc., complete for 10 users complete all as specified and as directed. |
| 174 | M&L Soakage wells exc, in ordinary Soil, Foundation in PCC 1:3:6, wells of Honey combed and solid in M-25 Concrete, including intercepting chamber, screen chamber Brick work in CM, RCC cover slab in M-25/RR Masonry/Filling with brick bats, complete of size 1.2M diaX3.0M effective depth complete all as specified and as directed. Please Enable Macros to View BoQ information |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
| 5 | Click here to download tender document | Tender Documents |
| 6 | Click here to download tender document | Tender Documents |
| 7 | Click here to download tender document | Tender Documents |
| 8 | Click here to download tender document | Tender Documents |
| 9 | Click here to download tender document | Tender Documents |
| 10 | Click here to download tender document | Tender Documents |
| 11 | Click here to download tender document | Tender Documents |
| 12 | Click here to download tender document | Tender Documents |
| 13 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
