|
| 1 | Earth work in excavation by manual means in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth asdirected:25 meter beyond 1 m from cutting edge |
| 2 | All kinds of soil |
| 3 | Ordinary Rock |
| 4 | Earth work in excavation by mechanical means (hydraulic excavator) in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts,wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed, within a lead of 50 metres: 2.9.1 All kinds of soil : |
| 5 | P/L dry stone soling duly han packed(Quarry) & Consolidated with hand rammers including carraige all complete job |
| 6 | Random Rubble masonry with hard stone in foundation and plinth including leveling up with cement concrete 1:6:12 (1 Cement : 6 coarse sand : 12 graded stone aggregate 20mm nominal size) upto plinth level and curing complete with:7.1.1 Cement mortar 1:6 (1 Cement : 6 coarse sand) |
| 7 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50 m and lift upto 1.5 m. |
| 8 | Stone soling including cost of stone |
| 9 | Centering and shuttering including strutting, propping etc. and removal of form work for:Foundations, footings, bases for columns |
| 10 | Centering and shuttering including strutting, propping etc. and removal of form work for:Lintel, beams, plinth beams, girders, bressumers and cantilevers. |
| 11 | Centering and shuttering including strutting, propping etc. and removal of form work for:Suspended floors, roofs, landings, balconies and access platforms. |
| 12 | Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15°, landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto five level including curing but excluding the cost of centring, shuttering, finishing and reinforcement with 5.3.1 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) |
| 13 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 14 | Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing in :Cement mortar 1:6 ( 1 cement : 6 coarse sand) |
| 15 | Extra for brick work with common burnt clay bricks/cement concrete bricks in superstructure above plinth level upto floor five level |
| 16 | CEMENT PLASTER (IN FINE SAND)12mm Cement plaster of mix: 13.1.1 1 : 4 ( 1 cement : 4 fine sand) |
| 17 | CEMENT PLASTER (IN FINE SAND)15mm Cement plaster on the rough side of single or half brick wall ofmix: 1 : 6 ( 1 cement : 6 fine sand) |
| 18 | CEMENT PLASTER (IN FINE SAND) 20mm Cement plaster of mix: 1 : 6 ( 1 cement : 6 fine sand) |
| 19 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fastenersshall be paid for separately): Second class deodar wood |
| 20 | Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note: -Butt hinges andnecessary screws shall be paid separately).Second kail wood |
| 21 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) |
| 22 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with:1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) |
| 23 | Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturers) of 1st quality conforming to IS: 15622 of approved make, laid on 20 mm thick bed of cement mortar 1: 4 ( 1 cement : 4 coarse sand) including pointing the joints with white cement and matching pigment etc., complete. 11.50.2 In all colours, shades, except White, Ivory, Fume Red Brown |
| 24 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shadesexcept burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement :3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 25 | Providing and applying white cement based putty of specified thickness, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 13.88.1 1 mm thick |
| 26 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade on New work (two or more coats) over and including priming coat with water thinnable cement primer |
| 27 | Finishing walls with acrylic smooth exterior paint of required shade on New work (Two or more coats applied @ 1.67 liter/10sqm over and including priming coat of exterior primer applied @ 2.20kg/10sqm) |
| 28 | Applying priming coat: 13.58.1 With ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood) |
| 29 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade.Two or more coats on new work |
| 30 | Providing and fixing ISI marked oxidized M.S. sliding door bolts with nuts and screws etc. complete :250x16 mm |
| 31 | Providing and fixing ISI marked oxidized M.S. tower bolt black finish, (Barrel type) with necessary screws etc complete. 150x10 mm |
| 32 | Providing and fixing ISI marked oxidized M.S. handles conforming to IS : 4992 with necessary screws etc. complete :100 mm |
| 33 | Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. Allworks upto plinth level 5.1.2 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) |
| 34 | Filling of brick bats in soakage pit in layers including cost of brick bat and carriage all complete |
| 35 | Cement concrete flooring 1:2:4 (1cement: 2 coarse sand: 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry and curing complete, but excluding the cost of nosing of steps etc.complete.11.3.3 50 mm thick with 20mm nominal size stone aggregate. |
| 36 | Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead upto 50 m and lift upto 1.5 m in -All kinds of soil. |
| 37 | Laying, spreading and compacting stone aggregate of specified sizes to WBM specifications in uniform thickness, hand picking, rolling with 3 wheeled road / vibratory roller 8-10 tonne capacity in stages to proper grade and camber, applying and brooming requisite type of screening/binding material to fill up interstices of coarse aggregate, watering and compacting to the required density. |
| 38 | Supplying and stacking at site Graded crushed stone aggregate of size 53 mm to 22.4 mm |
| 39 | Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colou r& pattern over 50mmthick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as per direction of Engineer-in-Charge. 16.93.1 60mm thick cement concrete paver block of M-35 grade with approved colour, design & pattern. |
| 40 | Structural steel work in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.10.2.2 Welded |
| 41 | Providing and fixing precoated galvanized iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. |
| 42 | Providing and fixing white vitreous china pedestal type water closet(European type W.C. pan) with seat and lid, 10 liter low level whiteP.V.C. flushing cistern, including flush pipe with manually controlled device (handle lever), conforming to IS:7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: W.C. pan with ISI marked white solid plastic seat and lid. |
| 43 | Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm sand cast Iron P or S trap, 10 liter low level white P.V.C. flushing cistern, including flush pipe (of approved make) with manually controlled device (handle lever) conforming to IS: 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required.White vitreous china Orissa pattern W.C. pan of size 580x440mm with integral type foot rests. |
| 44 | Providing and fixing G.I. inlet connection for flush pipe connecting with W.C. pan. |
| 45 | Providing and fixing wash basin with C.I. brackets, 15mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required : White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps. |
| 46 | Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing18.32.2 Rectangular shape 453x357 mm |
| 47 | Providing and fixing 600x120x5mm glass shelf with edges round off supported on anodized aluminum angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs, etc.complete |
| 48 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C waste fittings complete:Flexible pipe 40 mm dia |
| 49 | Providing and fixing of 15 mm CP bib cock of approved make ( Jaquar make) having code no. CON CHR 037 confirming to IS 2980 |
| 50 | Providing and fixing of CP Angle value of Jaquar make having code no. CON CHR053 |
| 51 | Providing and fixing of 600 mm long tower rail of approved make having code no. 1111 |
| 52 | Providing and fixing of scuare tower ring having code no. 1121 |
| 53 | Providing and fixing of CP soap dish of approved make having code no. 1131 N |
| 54 | Providing and fixing of CP paper holder of approved made with necessar screw and plastic gatti make having code no. 1151 |
| 55 | Providing and fix of CP shower of approved make having code no. 1799 incl. shower arm |
| 56 | Providing and fixing 10mm sand CP grating for gully, floor or nahani trap. |
| 57 | Providing and fixing of CP neeple of approved make |
| 58 | 100mm inlet and 100mm outlet sand cast iron S&S as per IS: 1729 |
| 59 | 100mm inlet and 75mm outlet sand cast iron S&S as per IS: 1729 |
| 60 | Providing and fixing G.I pipes complete with G.I fittings and clamps, including cutting and making good walls.25 mm dia nominal bore (medium) |
| 61 | Providing and fixing G.I pipes complete with G.I fittings and clamps, including cutting and making good walls.15mm dia nominal bore (medium) |
| 62 | Providing and fixing G.I pipes complete with G.I fittings and clamps, including cutting and making good walls.20mm dia nominal bore (medium) |
| 63 | Concealed pipe including painting with anti-corrosive bitumastic paint, cutting chases and making good the wall 15mm dia nominal bore |
| 64 | Concealed pipe including painting with anti-corrosive bitumastic paint, cutting chases and making good the wall 20mm dia nominal bore |
| 65 | Providing and fixing G.I pipes complete with G.I fittings and clamps, excluding trenching and refilling etc. (external work)(25mm dia nominal bore.) |
| 66 | Making connection of G.I distributing branch with G.I main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete.and making long screws etc. complete. (25 to 40mm nominal bore) |
| 67 | Fixing water meter and stop cock G.Ipipe line including cutting and threading the pipe and making long screws etc. complete. (cost of water meter and stop cock to be paid separately) (20 mm to 25 mm) |
| 68 | Providing and fixing ball value (brass) of approved quality complete. High or low pressure with plastic floats.20 mm nominal bore |
| 69 | Providing and fixing ball value (brass) of approved quality complete. High or low pressure with plastic floats.15 mm nominal bore |
| 70 | Providing and fixing of PVC pipe of 4Kg/ Cm Square of approved make ( Spureme) for carring disposal of seat and waste water of wash basin etc. incl. scalfoliding complete.100 mm |
| 71 | Providing and fixing of PVC pipe of 4Kg/ Cm Square of approved make ( Spureme) for carring disposal of seat and waste water of wash basin etc. incl. scalfoliding complete.75 mm |
| 72 | Providing and fixing PVC floor trape of supreme make of size 100x 75 |
| 73 | Providing and fixing of PVC collar of approved make of supreme make 100 mm |
| 74 | Providing and fixing of PVC collar of approved make of supreme make 75 mm |
| 75 | Providing and fixing of PVC plain bend of supreme make 100 mm |
| 76 | Providing and fixing of PVC plain bend of supreme make 75 mm |
| 77 | Providing and fixing of steel clamp of good quality incl. fixing the screws and making good the wall 100 mm |
| 78 | Providing and fixing of steel clamp of good quality incl. fixing the screws and making good the wall 75 mm |
| 79 | Providing and fixing of PVC Door bend of supreme make 100 mm |
| 80 | Providing and fixing of PVC Door bend of supreme make 75 mm |
| 81 | Providing and fixing of PVC door Tee 100 mm |
| 82 | Providing and fixing of PVC door Tee 75 mm |
| 83 | Providing and filling of joints in PVC pipe with solution and ring of required size 100 mm |
| 84 | Providing and filling of joints in PVC pipe with solution and ring of required size 75 mm |
| 85 | Making hole up to 20x20 cm and embedding pipes up to 150mm diameter in masonry and filling with cement concrete 1:3:6 (1 cement: 3 coarse sand 6 graded stone aggregate 20mm nominal size) including disposal of malba. |
| 86 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank |
| 87 | Constructing brick masonry chamber for underground C.I. inspection chamber and bend with common burnt clay (non modular) bricks of class designation 7.5 in cement mortar 1:4 ( 1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg ) R.C.C. top slab with 1:1 ½ : 3 mix ( 1 cement : 1 ½ coarse sand : 3 graded stone aggregate 20 mm nominal size),foundation concrete 1:5:10 (1 cement: 5 fine sand: 10 graded stone aggregate 40mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 ( 1 cement : 3 coarse sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design Inside dimensions 455x610 mm and 45 cm deep for singlepipe line- |
| 88 | Supplying and fixing C.I. cover without frame for manholes: 455x610mm rectangular C.I. cover (light duty) the weight of the cover to be not less than 23 kg. |
| 89 | Providing & fixing Solar LED Street Lighting Syastem Load Capacity 30W, Weight 15.5kgs, Batter Capacity 14.8/16AH, IP Rating IP66,IP65, Solar Module 60W/18V Monocrystalline with 5 years warranty, pole height 6mtr (complete Job) |
| 90 | Carriage of material by Mechanical Transport & Head Load including loading / unloading and stacking at site com |
| 91 | carraige of sand at an avg. distance of 45 Km by MT |
| 92 | Carraige of stone aggregate below 40mm at an avg. distance of 35km by MT |
| 93 | Carraige of stone aggregate 40mm nominal size and above at an avg. distance of 35km by MT |
| 94 | carraige of steel & C.G.I sheetat an avg. distance of 35 Km by MT |
| 95 | carraige of Cement at an avg. distance of 35 Km by MT |
| 96 | carraige of Brick at an avg. distance of 280 Km by MT |
| 97 | carraige of stones at an avg. distance of 15 KM by MT |
| 98 | carraige of earth/mulba at an avg. distance of 5 KM by MT Please Enable Macros to View BoQ information |
