|
| 1 | Demolition of un-reinforced cement concrete of any description and in any position not otherwise specially provided for complete all as specified and directed. |
| 2 | Demolition of unreinforced cement concrete in ground floors and pavings not exceeding 15cm thickness (below or above ground level) complete all as specified and directed. |
| 3 | Dismantling floor, hearth or wall/stone tiling including cement mortar bedding (but not backing), removing broken tiles and rubbish off the premises from site complete all as specified and directed. |
| 4 | Demolition of brick work built in cement mortor including all quoins,arches,pillars etc complete all as specified and directed. |
| 5 | Demolition of stone slabs and tiles of any description or thickness laid, bedded and pointed in any mortar in floors, aprons etc complete all as specified and directed. |
| 6 | Taking down cement plaster of any description on brick walls or concrete or stone and ceilings including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed. |
| 7 | Taking up or down existing 15mm bore steel water tubing and connections,including clreaning for refixing or removal, fixed/laid in any situation, complete all as specified and directed. |
| 8 | Taking up or down existing 20mm bore steel water tubing and connections,including clreaning for refixing or removal, fixed/laid in any situation, complete all as specified and directed. |
| 9 | Demolition and breaking of drain pipe (SGSW/PVC/RCC etc) set in cement mortar of internal dia 75mm taking out of trenches and taking down from walls, if required complete all as specified and directed. |
| 10 | Demolition and breaking of drain pipe (SGSW/PVC/RCC etc) set in cement mortar of internal dia 150 mm taking out of trenches and taking down from walls, if required complete all as specified and directed. |
| 11 | Hacking out old broken glass (any size, thickness, quality or description) from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones complete all as specified and directed. |
| 12 | Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and directed. |
| 13 | Taking down chowkats or frames with shutters (without taking off shutters from the frame) of size not exceeding 1.5 Sqm each including cutting holes in brick walls of appropriate size for insertion of cement concrete blocks for hold fasts, and removing from site complete all as specified and directed. |
| 14 | Taking down chowkats or frames with shutters (without taking off shutters from the frame) of size exceeding 1.5 Sqm but not exceeding 4 Sqm each including cutting holes in brick walls of appropriate size for insertion of cement concrete blocks for hold fasts, and removing from site complete all as specified and directed. |
| 15 | Taking down dhutters of any description exceeding 1.00Sqm but not exceeding 2.00Sqm each and removing from site complete all as specified and directed. |
| 16 | Demolition of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, complete all as specified and directed. |
| 17 | M&L for Lean Cement Concrete (1:2:4) type B-2 using 40mm graded crushed stone aggregate as in foundations, filling and mass concrete complete all as specified and directed. |
| 18 | M&L for Lean Cement Concrete (1:3:6) type C-0 using 10mm graded crushed stone aggregate as in filling back sides of pressed steel frames complete all as specified and directed. |
| 19 | M&L for brick work built in cement mortar (1:6) with sub class 'B' old size bricks, straight or curved on plan exceeding 6m mean radius complete all as specified and directed. |
| 20 | S&F Pressed steel frames made of 1.25mm thick CRCA sheet of profile 125x60mm for door and window frames with one or more rebates incl lock strike plate, shock absorbers, 20mm dia 60mm long MS conduit for housing of a drop bolt, butt hinges, hold fasts/lugs etc and treating of internal surfaces of chowkhats and hold fasts/lugs with a coat of coal tar or black paint incl hinges, hold fasts/lugs etc including making good jambs portion by providing plaster in CM 1:4 and finishes as per existing complete all as specified. |
| 21 | S&F Pressed steel frames made of 1.25mm thick CRCA sheet of profile 105x60mm for door and window frames with one rebate including lock strike plate, shock absorbers, 20mm dia 60mm long MS conduit for housing of a drop bolt, butt hinges, hold fasts/lugs etc and treating of internal surfaces of chowkhats and hold fasts/lugs with a coat of coal tar or black paint including hinges, hold fasts/lugs etc complete all as specified. |
| 22 | S&F 35mm thick factory made 2nd class hard wood (Hollock), plain framed, paneled shutters, any number of panels, panels shall be of 12mm thick BWR glade veneered particle board medium density, wood particle board with commercial face veneers, size of members as specified in clause 8.24 (a) of MES Schedule Part-I section-8 complete all as specified and directed. |
| 23 | S&F 35mm thick factory made 2nd class hard wood (Hollock), glazed and skeleton shutters open rebated and prepared to receive glass/ gauge etc (without sash bars), edges of framing plain chamfered or rounded, fitted with cut and mitered beads for securing glass etc for doors, size of members as specified in clause 8.24 (a) of MES Schedule Part-I Section-8, complete all as specified and directed. |
| 24 | S&FAnodised aluminium door shutters, powder coated aluminium (minimum 50micron thickness of epoxy powder coating)aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified and directed. |
| 25 | S&F Anodised aluminium window and ventilator shutters, powder coated aluminium (minimum 50micron thickness of epoxy powder coating) fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified and directed. |
| 26 | S&F Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-Charge,complete all as specified and directed. |
| 27 | S&F in replacement Factory Made Box Type Steel Windows with glazing bars made of ERW tube hollow \\"P\\" section of size 60mmX25mm double rebated outer frame comprising double shutters side hung skelton & glazed shutters, frame of ERW tube \\"P\\" section size 50mmX20mm with two openable leaf for each shutter consisting two Nos sash bar of T-section 20mmX3mm welded to frame with one vertical mullion of ERW box type T-section of size 60mmX25mm and mild steel flat iron 2mm thick welded/ screwed to frame for fixing of wire gauge to frame/ shutters as given below and all as shown on Drawing No. CEJZ/TD-1019/08 and CEJZ/TD-1020/08 Sheet No. 1/3 to 3/3 including taking down of old existing window complete all as specified and directed :- (i) Hold fast,150mm long of flat iron 12mmX3mm- 04Nos per window (ii) Handle of Z section 20mmX25mm,100mm long-01Nos per leaf (iii) MS Tower bolt 150mm long-02 Nos per leaf (iv) Z section 20mmX25mm,100mm long stopper -01 Nos per leaf (v) Cleat 55mm long of hollow square 15mmX12mm -02 Nos per leaf (vi) MS pintol hinges size 75mmx12mm- 2 Nos. per leaf (vii) Making good dismantled portion in PCC 1:2:4 type B-1 for hold fasts (four Nos for each window). (viii) Preparation of steel surfaces of windows and grills and guard bars and applying one one shop coat of zinc chromate primer and two coats of synthetic enamel paint after installtion at site. Note: Glass panes and grills & guard bars shall be measured and paid for separately .Area shall be measured flat for one side only for the purpose of measurement and payment . |
| 28 | S&F in replacement Factory Made Box Type Steel Ventilators side / top hung with glazing bars or dovetailed or welded made of ERW tube \\"P\\"-section of size 60mmx25mm outer frame ( single rebated), comprises glazed shutter, frame of ERW tube and mild steel flat iron 2mm thick welded/screwed to frame for fixing of sheet glass including fixture and fittings like as Stopper, Cleat, Pintal hinges, holdfast etc all as shown onDrawing No. CEJZ/TD-1019/08 and CEJZ/TD-1020/08 Sheet No. 1/3 to 3/3 including taking down of old existing window complete all as specified and directed:- Note : 1. Grills and guard bars, Sheet glass and wiremesh shall be measured and paid separately. 2. Making good dismantled portion in PCC 1:2:4 type B-1 for hold fasts (four Nos for each window). 3. Preparation of steel surfaces of ventlators and applying one one shop coat of zinc chromate primer and two coats of synthetic enamel paint after installtion at site. 4. Area shall be measured flat for one side only for the purpose of measurement and payment . |
| 29 | S&F 50mmx47mm size solid PVC door frame made out of 5mm plain colour PVC sheet reinforced with MS square tube, complete all as specified shown on drawing and specified and directed. |
| 30 | S&F factory made 30mm thick (style) solid panel PVC door shutter consisting of frame made out of MS tubes for top & bottom rails, MS frame covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, in the frame at site as per clause 8 B.2.1 of MES schedule Part-II (2004) complete all as specified shown on drawing and specified and directed. |
| 31 | S&F 18mm thick Prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work in plemet boxes, shelves, rebated or flat edges complete all as specified and directed. |
| 32 | S&F in repairs 18mm thick Celuka plywood of grade 1 quality one side prelaminated and otherside plain wihite colour to make kitchen cabinet/drawer/cub board shutters complete all as specified and directed. |
| 33 | S&F 100mm size mild steel butt hinges medium weight rolled cold complete all as specified and directed. |
| 34 | S&F 75mm size mild steel butt hinges medium weight rolled cold complete all as specified and directed. |
| 35 | S&F 200mm long aluminium anodised barrel tower bolts of extruded section and fixed with steel screws complete all as specified and directed. |
| 36 | S&F 125mm size aluminium door handle, extruded aluminium alloy, fabricated type complete all as specified and directed. |
| 37 | S&F 150mm size aluminium door handle, cast type, anodised complete all as specified and directed. |
| 38 | S&F stainless steel continous (piano) hinges of mild steel bright finish or electro galvanised with flap (when open) 25mm, fixed with steel screw complete all as specified and directed. |
| 39 | S&F 300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete all as specified and directed. |
| 40 | S&F in repairs 300mm size mild steel helical door spring ordinery rat rail rod pattern spring including roller and roller plate complete all as specified and directed, |
| 41 | S&F 150mm long PTMT tower bolts and fixed with steel screws complete all as specified and directed. |
| 42 | S&F 100mm long PTMT butt hinges and fixed with steel screws with brass /bronze hinges pin complete all as specified and directed. |
| 43 | S&F 150mm long PTMT handle and fixed with steel screws complete all as specified and directed. |
| 44 | S&F in repairs Aluminium body hydraullically regulated door closer universal type, suitable for door shutters of 851 to 1000mm width & of weight between 61 to 80kg complete allas specified and diected. |
| 45 | S&F Stainless Steel Wire Cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed. |
| 46 | S&F 5.5mm thick, plain sheet glass, Selected quality and glazing, with oil putty or with wooden/ EPDM Rubber beads (supplied alongwith shutters), in squares exceeding 0.50 Sqm in each pane complete all as specified and directed. |
| 47 | S&F 3.0mm thick, plain sheet glass, ordinary quality and glazing, with oil putty or with wooden beads (supplied alongwith shutters), in squares n.exc 0.50 Sqm in each pane complete all as specified and directed. |
| 48 | S&F 1.00mm thickness of laths Steel rolling shutters, with out ball bearing, as specified including top cover, an choring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete: push pull or manual type , complete all as specified and directed. |
| 49 | S&F 1.00mm thickness of laths Steel rolling shutters, with out ball bearing, as specified including top cover, an choring rod, hasp and staple and one shop coat of primer; erected in position as indi cated, gear operated type with bevel gear box and crank handle , complete all as specified and directed. |
| 50 | S&F Safety lever locks mild steel with 4 levers for rolling shutters complete all as specified and directed. |
| 51 | S&F ball bearing for rolling shutters complete all as specified and directed. |
| 52 | M&L for 75mm thick Plain Cement Concrete (1:4:8) type D-2 using 40mm graded crushed stone aggregate as in sub base of flooring, surface finished even and fair, surface finished rough to receive floor topping or interlocking tiles complete all as specified and directed. |
| 53 | M&L for 25mm thick Plain Cement Concrete (1:2:4) type B-1 using 20mm graded crushed stone aggregate as in surface finished rough to receive floor topping, surface finished even and fair complete all as specified and directed. |
| 54 | M&L for 18 to 20mm thick Granite (table rubbed and mirror polished) in steps ,jambs,pillars,cooking platform and like including pointing in white cement 1:2 using marble dust with admixture of pigment to match with marble shade other than white and black types over a 15mm thick cement screed bed or bedding layer in cement mortar (1:4) complete all as specified and directed. |
| 55 | M&L for 10mm thick (square/ rectangular) Vitrified Tiles, light colour, polished, area of each tile not exceeding 0.36Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match colour of tiles over and including 15mm thick screed bed or bedding layer in cement mortar (1:6) complete all as specified and directed. |
| 56 | M&L for 10mm thick (square/ rectangular) Vitrified Tiles, light colour, polished, area of each tile not exceeding 0.36Sqm, in vertical surfaces such as skirtings, dados, risers and steps etc set and jointed in neat cement slurry and pointed in white or coloured cement to match colour of tiles over and including 10mm thick rendering cement plaster in cement mortar (1:4) complete all as specified and directed. |
| 57 | M&L for 7 to 8 mm thick (square/ rectangular) Non-skid Ceramic Tiles coloured, premium quality, Joint-free, area of each tile exceeding 0.11Sqm but not exceeding 0.18Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match colour of tiles over and including 15mm thick screed bed or bedding layer in cement mortar (1:6) complete all as specified and directed. |
| 58 | M&L for 7 to 8 mm thick (square/ rectangular) Non-skid Ceramic Coloured Tiles, Joint-free, premium quality, area of each tile exceeding 0.11Sqm but not exceeding 0.18Sqm, in vertical surfaces such as skirtings, dados, risers and steps etc set and jointed in neat cement slurry and pointed in white or coloured cement to match colour of tiles over and including 10mm thick rendering cement plaster in cement mortar (1:4) complete all as specified and directed. |
| 59 | M&L for 7mm thick (Area 450 x 300mm / 450x350mm/ 350x250mm/300x200mm) Glazed Ceramic Coloured Tiles, in vertical surfacesX 7 mm th set and jonnted in cement slurry and pointed in white or coloured cement in vertical surfaces such as skirtings, dados, risers and steps etc set and jointed in neat cement slurry and pointed in white or coloured cement to match colour of tiles over and including 10mm thick rendering cement plaster in cement mortar (1:4) complete all as specified and directed. |
| 60 | M&L for providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paverblocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed. |
| 61 | M&L for 15mm thick rendering cement plaster in cement mortar (1:6) on fair faces of brick walls or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed. |
| 62 | M&L for 15mm thick rendering cement plaster in cement mortar (1:4) on other than fair faces of brick walls or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed. |
| 63 | M&L for 5mm thick rendering cement plaster in cement mortar (1:3) on ceiling surfaces, soffits of chajjas or roof projection and the like, finished even and smooth without using extra cement complete all as specified and directed. |
| 64 | M&L for cleaning the surface to remove loose particulars or any efflorescense on bricks and applying Silane Siloxane based water repellent coating FOSROC NITOCOTE SN 522 (or equivalent of SIKA/Berger/Asian Paints/Pidilite Dr Fixit) by evenly spraying or Brushing (coverage 7 Sqm per Ltr of NITOCOTE SN 522) on new plastered or unplastered surface upto window cill level complete as specified and directed. |
| 65 | M&L for applying bond coat of epoxy bonding agent & cement mortor in 1:1 ratio for bonding old and new concrete on damaged surfaces applying ready mix polymer modified mortar upto 60mm thickness (Chajjas fins, border,slab, beams etc) :-(i) Including application of rust remover on exposed reinforcement and subsequent application of anticorrosive coating. Also, pressure grouting with epoxy injection after application of polymer modified mortar.(ii) Use of electrical mixer to get the homogeneous dough on bond coat surfaces. (iii) To achieve required thickness repeat this step after 24 hrs as required.(iv) Keep the surfaces moist using water forg for 5 to 7 days etc complete all as specified and as directed.(v) Rate shall be inclusive of all necessary scaffolding for building height up to 24 meters complete all as directed by Engineer-in-Charge. Make :- Dr Fixit, MC Bauchemie, Cemisitik. Sikka, Basf, Fosroc, CIPIMake of Chemicals : - Epoxy bonding agent, Rust remover, Anti corrosive coating, Polymer modified mortar, Epoxy grout shall be of Berger Krishna/Dr Fixit/MC Bauchemie & M/s Cemistik/Sika or Equivalent as approved by GE.Notes : (i) Complete treatment to be executed by approved applicator (Applicator to be approved by GE). (ii) The Contractor and manufacture of polymer modified mortar shall give the warranty before commencement and also for the strengths achieved in the post completion of work.(iii) The chemicals to be used in the work shall be certified by the manufacturer with whom the MOU been entered into. (iv) Hard drawn steel wire fabric will be measured and paid seperately. complete all as specified and directed. |
| 66 | S&F 6mm thick Exposed metal frame ceiling with calcium silicate board of siliceous and calcareous material reinforced with cellulose fibre for fixing in 600 mm x 600mm grid (Frame work for ceiling shall be measured and paid parately) complete all as specified and directed. |
| 67 | S&F Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre complete all as specified and directed. |
| 68 | S & F in repair to Hollow PVC wall lining consisting of 5mm thick single side prelam PVC sheet instead of plain colour sheet inclusive of solvent cement and fixing on PVC frame as per specified in MES Schedule Part-I & II complete all as specified and directed. |
| 69 | M&L for complete removal of existing treatment on walls and distempering with two coats of distemper oil emulsion white or tinted over 1.0mm thick plaster of paris putty to prepare surface even and smooth complete all as directed. |
| 70 | M&L for preparing new plastered surfaces of walls and applying three coats of lime white wash complete all as specified and directed. |
| 71 | M&L for preparing new plastered surfaces of ceiling and applying three coats of lime white wash complete all as specified and directed. |
| 72 | M&L for preparing old plastered surfaces of walls and applying one coat of lime white wash complete all as specified and directed. |
| 73 | M&L for preparing old plastered surfaces of walls and applying two coats of lime white wash complete all as specified and directed. |
| 74 | M&L for preparing old plastered surfaces of ceiling and applying one coat of lime white wash complete all as specified and directed. |
| 75 | M&L for preparing old distempered plastered surfaces of walls including washing, rubbing down and stopping distempered and painted surfaces filling nails and distempering with two coats of oil bound distemper white or tinted complete all as specified and directed. |
| 76 | M&L for preparing old distempered plastered surfaces of walls including washing, rubbing down and stopping distempered and painted surfaces filling nails and distempering with one coat of oil bound distemper white or tinted complete all as specified and directed. |
| 77 | M&L for preparing old plastered surfaces of walls and applying two coats of cement base paint complete all as specified and directed. |
| 78 | M&L for preparing old plastered surfaces of walls and applying one coat of cement base paint complete all as specified and directed. |
| 79 | M&L for preparation of new wood or wood based surfaces of any description, not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed. |
| 80 | M&L for preparation of new steel and iron surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer zinc chromate complete all as specified and directed. |
| 81 | M&L for preparation of new steel and iron surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed. |
| 82 | M&L for preparation of new wood or wood based surfaces of any description, not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed. |
| 83 | M&L for preparation of old wood or wood based surfaces of any description, not otherwise described, over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed. |
| 84 | M&L for preparation of old steel and iron surfaces of any description, not otherwise described, over 10 cm width or girth and applying one coat of synthetic enamel paint over a coat of red oxide primer zinc chromate complete all as specified and directed. |
| 85 | S&F 75mm bore PVC (SWR) pipe single socketed, in any length with rubber ring joints, fixed to walls or floors complete all as specified and directed. Note:- Only Pipe along the centre line shall be measured and paid except fittings and accessories which shall be measured and paid for separately under respective items.) |
| 86 | S&F 110mm bore PVC (SWR) pipe single socketed, in any length with rubber ring joints, fixed to walls or floor complete all as specified and directed.Note:- Only Pipe along the centre line shall be measured and paid except fittings and accessories which shall be measured and paid for separately under respective items.) |
| 87 | S&F 75mm bore PVC (SWR) pipe single socketed, in any length with rubber ring joints, laid in trenches complete all as specified and directed.Note:- Only Pipe along the centre line shall be measured and paid except fittings and accessories which shall be measured and paid for separately under respective items.) |
| 88 | S&F 110mm bore PVC (SWR) pipe single socketed, in any length with rubber ring joints, laid in trenches complete all as specified and directed.Note:- Only Pipe along the centre line shall be measured and paid except fittings and accessories which shall be measured and paid for separately under respective items.) |
| 89 | S&F 75mm dia PVC (SWR) bends any radius complete all as specified and directed. |
| 90 | S&F 110mm dia PVC (SWR) bends any radius complete all as specified and directed. |
| 91 | S&F 75mm dia PVC (SWR)Junction single (single or double \\"T\\") equal or unequal complete all as specified and directed. |
| 92 | S&F 110mm dia PVC (SWR)Junction single (single or double T) equal or unequal complete all as specified and directed. |
| 93 | S&F 110mm dia PVC (SWR) vent cowl complete all as specified and directed. |
| 94 | S&F in repairs 75mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed. |
| 95 | S&F in repairs Stack clamps for 110mm dia pipe made out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof complete all as specified and directed. |
| 96 | S&F in repairs Stack clamps for 75mm dia pipe made out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof complete all as specified and directed. |
| 97 | S&F 15mm bore Galvanised Medium Grade Steel Water Tubing with all fittings and connections fixed complete to walls and celling or laid in floor, complete all as specified and directed. |
| 98 | S&F 20mm bore Galvanised Medium Grade Steel Water Tubing with all fittings and connections fixed complete to walls and celling or laid in floor, complete all as specified and directed. |
| 99 | Refixing only old retrieved serviceable 15mm bore Galvanised Medium Grade Steel Water Tubing and fixed to walls,and ceilings or laying in floors in new or old position with and including new fittings and connections complete all as specified and directed. |
| 100 | Refixing only old retrieved serviceable 20mm bore Galvanised Medium Grade Steel Water Tubing and fixed to walls,and ceilings or laying in floors in new or old position with and including new fittings and connections complete all as specified and directed. |
| 101 | S&F in repairs 15mm bore Bib Taps, long body fancy type, chromium plated, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule complete all as specified and directed. |
| 102 | S&F in repairs 15mm bore fancy type, chromium plated, Stop valves, cast copper alloy, with long shank and cup concealed type, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed. |
| 103 | S&F in repair 15mm bore Angle Valves, fancy type, chromium plated, cast copper alloy, with flange, one way turn, screwed down high pressure, with crutch or butterfly handle, screwed for iron pipe complete all as specified and directed. |
| 104 | S&F in repairs 15mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipes complete all as specified and directed. |
| 105 | S&F in repairs 20mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipes complete all as specified and directed. |
| 106 | S&F in repair 15mm bore push tap any colour of PTMT suitable for urinals screwed for iron pipe and fixed(minimum weight 15mm-47 gms) complete all as specified and directed. |
| 107 | S&F in repair 15mm bore dia Bib tap standard of PTMT any colour high pressure screwed for iron pipe but with long body and fixed.(Minimum weight 15mm-90gms complete all as specified and directed. |
| 108 | S&F in repair 15mm bore Pillar taps of PTMT any colour fancy type high pressure screwed for iron pipe and fixed.(Minimum weight15mm-120gms complete all as specified and directed. |
| 109 | S&F in repair 15mm bore Stop valve of PTMT any colour high pressure screwed for iron pipe and fixed. (Minimum weight 15mm-90gms) complete all as specified and directed. |
| 110 | S&F in repairs 15mm bore Pillar Taps, fancy type, chromium plated, cast copper alloy, with capstan heads, screwed down high pressure, with or without lettered 'HOT' or 'COLD' with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed. |
| 111 | S&F in repair push tap 15 mm bore any colour of PTMT suitable for urinals screwed for iron pipe and fixed(minimum weight 15mm-47 gms) complete all as specified and directed. |
| 112 | S&F in repairs 32mm bore PVC waste pipe of suitable length to waste coupling pipe attached with rubber ring joints/ PVC threaded cup, fixed to waste coupling of sinks / WHBs/urinal of required length complete all as specified and directed. |
| 113 | S&F in repairs 32mm bore Waste coupling of PTMT (half or full threaded) (Minimum weight 32mm 45gms/40mm-60 gms) complete all as specified and directed. |
| 114 | S&F in repairs 15mm PVC connections 450mm long heavy duty with PTMT nuts adaptors and washers and rubber gaskets at both ends complete all as specified and directed. |
| 115 | S&F in replacement 500 litres capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top), three layered, ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. including 20mm dia ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule hoisted and fixed including dismentling and taking down old unserviceable water tank capacity 500 litres complete as specified in SSR Part-I. complete all as specified and directed. |
| 116 | S&F in replacement 1000 litres capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top), three layered, ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. including 20mm dia ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule hoisted and fixed including dismentling and taking down old unserviceable water tank capacity 1000 litres complete as specified in SSR Part-I. complete all as specified and directed. |
| 117 | S&F 15mm bore Ball valves high pressure of PTMT withepoxy coated Aluminium rod & high density plastic float ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/ 20mm-210gms./25mm-455gms/ 40mm- 690 gms) complete all as specified and directed. |
| 118 | S&F in repars 15mm bore Ball valves high pressure of PTMT withepoxy coated Aluminium rod & high density plastic float ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/ 20mm-210gms./25mm-455gms/ 40mm- 690 gms) complete all as specified and directed. |
| 119 | S&F in repars 20mm bore Ball valves high pressure of PTMT withepoxy coated Aluminium rod & high density plastic float ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/ 20mm-210gms./25mm-455gms/ 40mm- 690 gms) complete all as specified and directed. |
| 120 | S&F in repairs Wash Hand Basins, Vitreous China (flat back) white of size 550mm X 400mm including cutting for and pinning in ends of brackets or erecting stand including waste fittings, 32 mm bore PVC flush pipe with long screwed shucks and fly nuts and including PVC discharge pipe complete all as specified and directed. |
| 121 | S&F in repairs Vitreous China Squatting Pan, \\"Orissa pattern\\", size 580x440mm white/ coloured with integral foot rests (excluding flushing cistern, flush pipe and waste pipe), including trap and connection to trap, and to flushing pipe, anti-syphonage pipe, etc.complete including all joints and making good to floors complete all as specified and directed. |
| 122 | S&F in repairs Vitreous China Wash Down Water Closet Pan (pedestal pattern) complete, white/ coloured including seat and cover, trap, including connection to drain (or outgoing pipe), and to flushing pipe, anti-syphonage pipe, etc. etc.complete including all joints and making good to floors complete all as specified and directed. |
| 123 | S&F single piece WC of size 665x360x750mmm with flushing cistern and connection pipe P or S trap (Closed pattern incl all necessary accessories like rag bolts, kit/gel gasket etc (including flushing cistern, pvc seat cover, jet and flush pipe complete all as specified and directed. |
| 124 | S&F in repairs Vitreous China urinals, flat back of size 465x355x265mm complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) complete including all joints and making good to floors complete all as specified and directed. |
| 125 | S&F in repairs 10 litres capacity low level PVC valveless syphonic action type flushing cistern with inlet ball valve, float and flush handle complete all as specified and directed. |
| 126 | S&F in repairs PVC Syphon fitting , ball valve with float with washer and hand for 10 litres capacity low level PVC valveless syphonic action type flushing cistern complete all as specified and directed. |
| 127 | S&F in repairs Health faucet (ABS Body) mild steel chromium plated suitable for 15mm dia pipe with 1.25m long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified complete all as specified and directed. |
| 128 | S&F in repairs brass spindle with washers for 15mm bore for CP brass fancy bib tap, pillar tap, mixers etc complete all as specified and directed. |
| 129 | S&F in repairs CP brass Handle with washers for 15mm bore CP brass fancy bib tap, pillar tap, mixers etc complete all as specified and directed. |
| 130 | S&F in repairs 32mm bore Waste coupling of PTMT (half or full threaded) (Minimum weight 32mm 45gms/40mm-60 gms) complete all as specified and directed. |
| 131 | S&F in repairs sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs,washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed. |
| 132 | S&F in repairs sinks made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or includingfixing cantilever brackets and connecting union to pipe,overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and directed. |
| 133 | S&F in repair Stainless steel plate rack of standard pattern & of size 900 x 750 x 250 mm.The thickness of stainless steel sheet shall be 1.00 mm & grade of sheet shall be 304 AISI including fixing to wall with 4 Nos 50mm screws & PVC rawl plugs complete all as specified and directed. |
| 134 | S&F in repairs grating doom 100mm dia of PTMT with waste hole of PTMT. (Minimum weight 40gms) complete all as specified and directed. |
| 135 | S&F 100mm dia grating doom of PTMT with waste hole of PTMT. (Minimum weight 25gms) complete all as specified and directed. |
| 136 | S&F in repairs Swivel shower of PTMT any colour for fixing with 15mm pipe. (Minimum weight 40gms) with Shower arm 15 mm size, 195mm long with bend of 45degree with flange of PTMT any colour.(Minimum weight 40gms complete all as specified and directed. |
| 137 | S&F in repirs 600mmx450mm size of specified thickness looking mirror, bevelled edge of selected quality glass with aluminium frame made of channel around, mounted on 6mm thick commercial ply or AC building board, fitted to wooden plug with chromiumplated brass screws and cup washers complete all as specified and directed. |
| 138 | S&F in repairs 20mm dia brass chromium plated tubular towel rail 600mm long between flanges type \\"D\\", with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 190gms)complete all as specified and as directed. |
| 139 | S&F in repairs Towel Rail 600mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 190gms)complete all as specified and as directed. |
| 140 | S&F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed. |
| 141 | S&F in repairs Chromium plated Soap dish of stainless steel of size 160x160mm x 1mm thick, fixed to wall with CP brass screws and PVC gutties complete all as specified and directed. |
| 142 | S&F in repair Towel Ring of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 90gms) complete all as specified and directed. |
| 143 | S&F in repairs 20mm dia mild steel epoxy powder coated curtain rod with fancy type brackets including with all fittings rings @ 10 nos per RM , bulbs, finials, fixed with PVC rawl plugs and CP steel screws complete all as specified and directed. |
| 144 | S&F in repairs 15mm bore chromium plated Wall Mixer for WHB for mixing hot and cold water screwed down for pipe connecting legs and wall flange complete all as specified and directed. Please Enable Macros to View BoQ information |
