|
| 1 | Earth work in excavation in ordinary soil in all of foundation trenches including dressing of the side and ramming of bottom.Lifts up to 1.50 m including getting out the excavated soil and disposal of surplus excavated soil as directed with in a lead of 50m. (MOST/A.R./YEIDA) |
| 2 | Cement concrete with 4cm gauge approved stone ballast, coarse sand & cement in the proportion of 8:4:1 including supply of all material, Labour, Tools&plants etc required for proper completion of the work. |
| 3 | B/W with bricks of class 150 in foundation & plinth in CM 1:4 (Based on UP PWD SOR 2020) Cement mortar 1:4 ( 1cement :4Coarse sand) |
| 4 | M-150 brick work in 1:4 one cement and four course sand 2.20 F.M. mortar superstructure but for walls of half brick thick including supply of all material, labour, T&P etc. required for proper completion of the work. (UPPWD/SOR-2020/305(a)+310A |
| 5 | Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. (Note :- Cement content considered in this item is @ 330 kg/cum. Excess/ less cement used as per design mix is payable/recoverable separately). All works upto plinth level |
| 6 | Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. (Note :- Cement content considered in this item is @ 330 kg/cum. Excess/ less cement used as per design mix is payable/recoverable separately).All works above plinth level upto floor V level |
| 7 | Centring and shuttering including strutting, propping etc. and removal of form for : foundation footings, base of column |
| 8 | Centring and shuttering including strutting, propping etc. and removal of form for : lintels, beams, plinth beam, grinder |
| 9 | Centring and shuttering including strutting, propping etc. and removal of form for : suspended floors, roofs, landings |
| 10 | Edges of slabs and breaks in floors and walls: Under 20 cms wide. (DAR/5.9.16.1/Based on UPPWD/SOR-2020)) |
| 11 | Earth work in rough excavation , banking excavaated earth in layers not exceeding 20 cm in depth, breaking clods watering, rolling each layer with 1/2 tonnes roller or wooden or steel rammer and rolling every 3rd and top most layer with power roller of minimum 8 tonnes and dressing up in embankments for roads, flood banks, marginal banks and guide banks or filling up ground depressions, all leads as per ( A.R. ) For all kind of soil. |
| 12 | Steel rainforcement for R.C.C. work including straightening, cutting bending, placing in position and binding all complete upto plinth level Thermo-Mechanically Treated bars of grade Fe-500D or more./Cold twisted bars. (DAR/5.22.6/Based on UPPWD/SOR-2020)) |
| 13 | Dismentaling Of Cement Plaster 12 mm cement Plaster (1:4) uppwd sor-2020 DAR-18/13.4.1 |
| 14 | 12mm cement plaster of mix: 1:6 (1 cement : 6 coarse sand) BASED on UP PWD SOR 2020 DAR-18/13.4.2 |
| 15 | 6mm cement plaster of mix: 1:3 (1 cement : 3 coarse sand) BASED on UP PWD SOR 2020 DAR-18/13.17 |
| 16 | 15mm cement plaster of mix: 1:6 (1 cement : 6 coarse sand) BASED on UP PWD SOR 2020 DAR-18/13.4.2 |
| 17 | Finishing walls with Acrylic Smooth exterior paint of required shade: New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including base coat of water proofing cement paint applied @ 2.20 kg/ 10 sqm). |
| 18 | Distempering with dry distemper of approved brand and manufacture (two or more coats) of required shade on new work, over and including water thinnable priming coat to give an even shade |
| 19 | Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.DAR-18/13.26 |
| 20 | Painting with synthetic enemel paint of approved brand and manufacture to give an even shade: Two or more coats on new work. |
| 21 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110mm dia |
| 22 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Single tee with door 110x110x110 mm (DAR/12.42.3.2/Based on UPPWD/SOR-2020) |
| 23 | Bend 87.5° 110 mm bend (DAR/12.42.5.2/Based on UPPWD/SOR-2020) |
| 24 | Shoe (Plain) 110 mm Shoe (DAR/12.42.6.2/Based on UPPWD/SOR-2020) |
| 25 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 110 mm (DAR/12.43.2/Based on UPPWD/SOR-2020) |
| 26 | Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams. (DAR/12.44/Based on UPPWD/SOR-2020) |
| 27 | Steel work welded in built up sections/ framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.DAR-18/10.25.2 |
| 28 | Providing and fixing 1 mm thick M.S. sheet sliding-shutters, with frame and diagonal braces of 40x40x6 mm angle iron, 3 mm M.S. gusset plates at the junctions and corners, 25 mm dia pulley, 40x40x6 mm angle and T- iron guide at the top and bottom respectively, including applying a priming coat of approved steel primer UPPWD SOR-2020/DAR-18/10.4 |
| 29 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge.Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) UP PWD SOR 2020/DAR-18/15.2.1 |
| 30 | Providing and fixing water closet squatting pan (Indian type W.C. pan with 100mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required White Vitreous china Orissa pattern W.C. pan of size 580x440mm with integral type foot rests.DAR 18/17.1.1 |
| 31 | Providing and fixing wash basin with C.l. brackets, 15 mm C.P. brass pillar taps,32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required: UPPWD SOR-2020/DAR-18/ 17.7.1 |
| 32 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.20mm OD pipes. (DAR/18.8.2/Based on UPPWD/SOR-2020) |
| 33 | 25mm OD pipes. (DAR/18.8.3/Based on UPPWD/SOR-2020) |
| 34 | Providing and fixing brass gate valve with C.I. wheel of approved quality (screwed end) : 25 mm nominal bore. (DAR/18.17.1/Based on UPPWD/SOR-2020) |
| 35 | 32 mm nominal bore. (DAR/18.17.2/Based on UPPWD/SOR-2020) |
| 36 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI: 12701 marked with cover and suttable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank DAR 18/ 18.48 |
| 37 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600mm (DAR/11.41.2/Based on UPPWD/SOR-2020)) |
| 38 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. (DAR/8.31/Based on UPPWD/SOR-2020)) |
| 39 | Providing and laying Ceramic glazed floor tiles of required size (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete.(DAR/11.37/Based on UPPWD SOR/2020) |
| 40 | Providing and fixing brass bib cock of approved quality: 15 mm nominal bore (DAR/18.15.1/Based on UPPWD/SOR-2020)) |
| 41 | Providing and fixing brass gate valve with C.I. wheel of approved quality (screwed end) : 25 mm nominal bore. (DAR/18.17.1/Based on UPPWD/SOR-2020) |
| 42 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 30mm thick including ISI marked stainless steel butt hinges with necessary screws. (DAR/9.21.2/Based on UPPWD/SOR-2020)) |
| 43 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5 mm thickness (weight not less than 12.50 kg/ sqm) (DAR 2018-21.3.2)Based on UPPWD SOR/2020 |
| 44 | Providing and fixing square-mouth S.W. gully trap class SP-1 complete withC.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design:(DAR/19.4.1/Based on UPPWD/SOR-2020) |
| 45 | Providing and fixing Heavy Class SS grating of approved design including setting in floor with cement motor to match with floor finish as per architect requirement suitable for waster and FT, UT & FD.Size 150 mm X 150 mm |
| 46 | Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms. (DAR/17.73.2/Based on UPPWD/SOR-2020)) |
| 47 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. (DAR/17.31/Based on UPPWD/SOR-2020)) |
| 48 | Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms. (DAR/18.65/Based on UPPWD/SOR-2020)) |
| 49 | Providing and fixing PTMT extension nipple for water tank pipe, fittings of approved quality and colour.25mm nominal bore, weighing not less than 62 gms. (DAR/18.75.3/Based on UPPWD/SOR-2020)) |
| 50 | Providing & Fixing of CP Heavy Duty Bottle Trap 32mm. (Complete complying with relavent standard specification and as directed by the Competent authority.) For Wash basin& Urinal |
| 51 | Construction of Granular Sub-Base by providing close graded material, mixing in mechanical mix plant at OMC, carriage of mixed material to work at site, spreading uniform layers with motor grader on prepared surface and compacting with vibratory roller to achieve the desired density, complete as per clause 401 for Grade-1 material. (MORTH/(AR/YEIDA/Based on UPPWD/SOR-2020) |
| 52 | Providing and laying 80mm thick I.S.I. mark factory made cement concrete interlocking concrete paver block made by block making machine with strong vibratory compaction of approved size, design, shape, laid in required colour and pattern over and including average 50mm thick compacted bed coarse sand and filling the joints with fine sand all complete as per the direction of Engineer-in-charge with conforming to IS-15658 and IRC:SP:63. (AR/YEIDA/ Based on UPPWD/SOR-2020) |
| 53 | Wiring point for light in 1.5 sq. mm. PVC insulated single core copper conductor cable (in PVC conduit with 1.5 sq.mm. FRLSH PVC insulated multistrand copper conductor cable as earth wire drawn inside conduit.) and 5 Amp.flush type switch & ceiling rose/angle/batten holder fixed with 3mm thick phenolic laminate backalite sheet with brass machine screws and cup washers mounted over existing M.S. switch board box/ junction box with supply of all material, labour & T&P etc. required for proper completion of the work complete in all respect, as directed by Engineer in charge PWD-2018 PS No-174C |
| 54 | Supply and Wiring of submains with 2 nos. of 2.5 sq. mm. FRLSH PVC insulated 1100 V grade multistrand single core copper conductor cable in 25 mm dia heavy duty (2 mm thick) PVC conduit with 2 nos 2.5 sq.mm. FRLSH PVC insulated multistrand copper conductor cable as earth continuity wire drawn in conduit complete in all respect, as directed by Engineer in charge PWD-2018 PS No-261C |
| 55 | Supply and fixing of power plug with 20 Amp./250 volt flush type modular switch and 5 pin 20 A/250 volt flush type universal modular socket switch on concealed M.S box including supply of all material, labour T&P etc. complete in all respect, as directed by Engineer in charge .PWD-2018 PS No-1139A |
| 56 | S&F surface/flush mounting 8 ways SPN distribution board with additional metal door without MCB complete in all respect, as directed by Engineer in charge. PWD-2018 PS -1024A |
| 57 | S&F of 6 Amp to 32 Amp. MCB (10 KA) C Curve complete in all respect, as directed by Engineer in charge.PWD-2018 PS -1002 CAT-A |
| 58 | S&F of 40 Amp. DP MCB (10 KA) C Curve complete in all respect, as directed by Engineer in charge. PWD-2018 PS No-1010 Cat-A |
| 59 | Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing. (DAR/10.18/Based on UPPWD/SOR-2020)) |
| 60 | Providing ,Fixing and commisoining of single phasesubmersible pump set in existing Bore well suitablefor 45 LPM Discharge 25 Mtr to 70 Mtr Head minimumTwo Star rating of approved make PVC cable supportwire starter etc complete in all respect including costof dismantling of existing hand pump machinecomplete Labour T and P etc .from bore wellapproved quality as per direction by Eng. in charge(language and rate based on Submersible fixing Itemno-1)(MR) 3 HP SINGLE PHASE |
| 61 | Supply and errected ceiling fan 600mm including regulators complete with approved brand. |
| 62 | Lettering with black japan paint of approved brand and manufacture DAR/13.71/Based on UPPWD/SOR-2020) |
| 63 | Dry brick on edge flooring in required pattern with bricks of class designation 150 on a bed of earth including filling compressed, with M-150 bricks.(DAR/11.2/AR/YEIDA/Based on UPPWD/SOR -2020) |
| 64 | Chequered terrazo tiles 22 mm thick with graded marble chips of size up to 6 mm in floors, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and polishing complete, on 20 mm thick bed of cement mortar 1:4 (1 cement :4 coarse sand) : Light shade pigment using white cement. Based on UPPWD/SOR/DAR/11.19.1 |
| 65 | Sit Up Station: Providing, designing and fixing of double sit-up station of size 1500 x 1150 x 650mm fabricated with main post of 114mm dia and 2.5mm thick and rest of the pipe of 40mm dia and 2.5mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized and powder coated using Akzo Nobel or equivalent of 80 - 120 micron thick. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Seat and base plate cover to be made up from virgin LLDPE manufactured by rotationalMolding with minimum thickness of plastic as 8mm, colorful and UV resistant and environmental friendly. The equipment to be fixed on ground with concrete of minimum strength M-25 and J shape welded bolts and once the concrete is set, fix the equipments on to it and cover nuts and bolts with the base plate.All complete as per direction and approval of engineer-in-charge regarding material, shape of equipment, colour on metal, seat and base pedal) and fixing of equipments etc. (the cement concrete and excavation work shall be paid separately). |
| 66 | Leg Press: Providing, designing and fixing of leg press of size 2000 x 550 x 1600 mm fabricated with main post of 114mm dia and 2.5mm thick and rest of the pipe 40mm dia and 2.5mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized and powder coated using Akzo Nobel or equivalent of 80 - 120 micron thick. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Handle bars to be provided with high quality grip rubber on top end. Pedals shall be made up of Nylon alloy with rounded edges to prevent any impact of injury. Seat and base plate cover to be made up from virgin LLDPE manufactured by rotational molding with minimum thickness of plastic as 8mm, colorful and UV resistant and environmental friendly. Bearing used shall be maintenance free, duly oil sealed and self lubricated made by reputed company to be approved by Engineer in charge. Equipment to be fitted with inbuilt limiters to prevent unwanted movements. All open ends of pipe to be closed by GI/ LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M-25 and J shape welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate. All complete as per direction and approval of engineer-in-charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipments etc (the cement concrete and excavation work shall be paid separately). |
| 67 | Seated chest press: Providing, designing and fixing of seated chest press in a pair of size 1800 x 700 x 2000 mm fabricated with main post of 114mm dia and 2.5mm thick and rest of the pipe 40mm dia and 2.5mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized and powder coated using Akzo Nobel or equivalent of 80 - 120 micron thick. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Handle bars are to be provided with high quality grip rubber. Pedals shall be made up of Nylon alloy with rounded edges to prevent any impact or injury. Seats and base plate cover to be made up from virgin LLDPE manufactured by rotational mounding with minimum thickness of plastic as 8mm, colorful and UV resistant and environmental friendly. Bearing used shall be maintenance free, duly oil sealed and self lubricated made by reputed company to be approved by Engineer in charge. Equipment to be fitted with inbuilt limiters to prevent unwanted movement. All open ends of pipe to be closed by GI/ LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M-25 and J shape welded bolt and once the concrete is set, fix the equipment on to it and cover with the base plate. All complete as per direction and approval of engineer-in-charge regarding material, shape of equipment, colour on metal, seat and base plate and fixing of Equipments etc (the cement concrete and excavation work shall be paid separately). |
| 68 | Arm wheel: Providing, designing and fixing of arm wheel in a pair of size 850 x 800 x 1800 mm fabricated with main post of 114mm dia and 2.5mm thick and rest of the pipe 40mm dia and 2.5mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized and powder coated using Akzo Nobel or equivalent of 80 - 120 micron thick. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Handle bars are to be provided with high quality grip rubber. Pedals shall be made up of Nylon alloy with rounded edges to prevent any impact or injury and base platecover to be made up from virgin LLDPE manufactured by rotational mounding with minimum thickness of plastic as 8mm, colorful and UV resistant and environmental friendly. Bearing used shall be maintenance free, duly oil sealed and self lubricated made by reputed company to be approved by Engineer in charge. Equipment to be fitted with inbuilt limiters to prevent unwanted movement. All open ends of pipe to be closed by GI/ LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M-25 and J shape welded bolts and once the concrete is set, fix the equipments on to it and cover with the base plate. All complete as per direction and approval of engineer-in-charge regarding material, shape of equipment, colour on metal, seat and base plate and fixing of equipments etc (the cement concrete and excavation work shall be paid separately). |
| 69 | Twister: Providing, designing and fixing twister of size 1700 x 1300 x 1300 mm fabricated with main post of 114mm dia and 2.5mm thick and rest of the pipe 40mm dia and 2.5mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized and powder coated using Akzo Nobel or equivalent of80 - 120 micron thick. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Handle bars are to be provided with high quality grip rubber. Foothold shall be made up of nylon alloy with rounded edges to prevent any impact or injury and base plate cover to be made up from virgin LLDPE manufactured by rotational mounding with minimum thickness of plastic as 8mm, colorful and UV resistant and environmental friendly. Bearing used shall be maintenance free, duly oil sealed and self lubricated made by reputed company to be approved by Engineer in charge. Equipment to be fitted with inbuilt limiters to prevent unwanted movement. All open ends of pipe to be closed by GI/ LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M-25 and J shape welded bolts and once the concrete is set, fix the equipments on to it and cover with the base plate. All complete as per direction and approval of engineer-in-charge regarding material, shape of equipment, colour on metal, seat and base pedal and fixing of equipments etc (the cement concrete and excavation work shall be paid separately). |
| 70 | Air Swing: Providing, designing and fixing of air swing in pair of size 1150 x 900 x 1250mm fabricated with main post of 114mm dia and 2.5mm thick and rest of the pipe 40mm dia and 2.5mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized and powder coated using Akzo Nobel or equivalent of 80 - 120 micron thick. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Pedals shall be made of Nylon alloy with rounded edges to prevent any impact of injury and base plate cover to be made from virgin LLDPE manufactured by rotational molding with minimum thickness of plastic of 8mm, colorful and UV resistant and environmental friendly. Bearing used shall be maintenance free, duly oil sealed and self lubricated made by reputed company to be approved by Engineer in charge. Equipment to be fitted with inbuilt limiters to prevent unwanted movements. All open ends of pipe to be closed by GI/ LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M-25 and J shape welded bolts and once the concrete is set, fix the Equipment on to it and cover nuts and bolts with the base plate. All complete as per direction and approval of engineer-in-charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipments etc (the cement concrete and excavation work Shall be paid separately). |
| 71 | Horse rider station: Providing, designing and fixing of horse rider station of size 1000 x 600 x 1100 mm fabricated with main post of 114mm dia and 2.5mm thick and rest of the pipe 40mm dia and 2.5mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized and powder coated using Akzo Nobel or equivalent of 80 - 120 micron thick. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Pedals shall be made up of Nylon alloy with rounded edges to prevent any impact of injury. Base plate cover and seat to be made up from virgin LLDPE manufactured by rotational mounding with minimum thickness of plastic as 8mm, colorful and UV resistant and environmental friendly. Bearing used shall be maintenance free, duly oil sealed and self lubricated made by reputed company to be approved by Engineer in charge. Equipment to be fitted with inbuilt limiters to prevent unwanted movement. All open ends of pipe to be closed by GI/ LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M-25 and J shape welded bolt and once the concrete is set, fix the equipment on to it and cover with the base plate. All complete as per direction and approval of engineer-in-charge regarding material, shape of equipment, colour on metal, seat and base cover plate cover and fixing of equipments etc (the cement concrete and excavation work shall be paid separately). |
| 72 | Elliptical exerciser: Providing, designing and fixing elliptical exerciser of size 1200 x 540 x 1600 mm fabricated with main post of 114mm dia and 2.5mm thick and rest of the pipe 40mm dia and 2.5mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized and powder coated using Akzo Nobel or equivalent of 80 - 120 micron thick. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Handle bars are to be provided with high quality grip rubber. Pedals shall be made up of Nylon alloy with rounded edges to prevent any impact or injury and base plate cover to be made up from virgin LLDPE manufactured by rotational mounding with minimum thickness of plastic as 8mm, colorful and UV resistant and environmental friendly. Bearing used shall be maintenance free, duly oil sealedAnd self lubricated made by reputed company to be approved by Engineer in charge. Equipment to be fitted with inbuilt limiters to prevent unwanted movement. All open ends of pipe to be closed by GI/ LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M-25 and J shape welded bolts and once the concrete is set, fix the equipments on to it and cover with the base plate. All complete as per direction and approval of engineer-in-charge regarding material, shape of equipment, colour on metal, seat and base plate and fixing of equipments etc (the cement concrete and excavation work shall be paid separately). |
| 73 | Double cross walker: Providing, designing and fixing double cross walker of size 1600 x 600 x 1600 mm fabricated with main post of 114mm dia and 2.5mm thick and rest of the pipe 40mm dia and 2.5mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized and powder coated using Akzo Nobel or equivalent of 80 - 120 micron thick. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Pedals shall be made up of Nylon alloy with rounded edges to prevent any impact or injury and base plate cover to be made up from virgin LLDPE manufactured by rotational mounding with minimum thickness of plastic as 8mm, colorful and UV resistant and environmental friendly. Bearing used shall be maintenance free, duly oil sealed and self lubricated made by reputed company to be approved by Engineer in charge. Equipment to be fitted with inbuilt limiters to prevent unwanted movement. All open ends of pipe to be closed by GI/ LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M-25 and J shape welded bolts and once the concrete is set, fix the equipments on to it and cover with the base plate. All complete as per direction and approval of engineer-in-charge regarding material, shape of equipment, colour on metal, seat and base pedal and fixing ofEquipments etc (the cement concrete and excavation work shall be paid separately). |
| 74 | Bridge Ladder: Providing, designing and fixing bridge ladder of size 2750 x 1000 x 1500 mm fabricated with main post of 114mm dia and 2.5mm thick and rest of the pipe 40mm dia and 2.5mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized and powder coated using Akzo Nobel or equivalent of 80 - 120 micron thick. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Handle bars are to be provided with high quality grip rubber. Foothold shall be made up of nylon alloy with rounded edges to prevent any impact or injury and base plate Cover to be made up from virgin LLDPE manufactured by rotational mounding with minimum thickness of plastic as 8mm, colorful and UV resistant and environmental friendly. Bearing used shall be maintenance free, duly oil sealed and self lubricated made by reputed company to be approved by Engineer in charge. Equipment to be fitted with inbuilt limiters to prevent unwanted movement. All open ends of pipe to be closed by GI/ LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M-25 and J shape welded bolts and once the concrete is set, fix the equipments on to it and cover within the base plate. All complete as per direction and approval of engineer-in-charge regarding material, shape of equipment, colour on metal, seat and base pedal and fixing of equipments etc (the cement concrete and excavation work shall be paid separately). |
| 75 | Earth work in excavation by mechanical means (Hydraulic excavator) /manual means over areas (exceeding 30cm in depth. 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50m and lift up to 1.5m, disposed earth to be leveled and neatlyDressed. All kinds of soil DAR 2018 page 76 item 2.6.1 |
| 76 | Cement Concrete with 4 cm gauge approved stone ballast coarse sand & cement in the proportion of 8:4:1 including supply of all materials labour tools & plants etc reguired for proper complection of the work |
| 77 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level: a)1:1½ :3 (1 cement : 1½ coarse sand (Zone-III): 3 graded stone aggregate 20mm nominal size). (D.A.R.2018 Page No. 88 Item No. 4.1.2 Please Enable Macros to View BoQ information |
