|
| 1 | Taking down chowkats or frame exc 1.5 Sqm and n exc 4 Sqm each (without taking off shutter from the frame) all as specified and as directed. |
| 2 | Taking down chowkats or frame n exc 1.5 Sqm each (without taking off shutter from the fram) all as specified and as directed. |
| 3 | Taking down shutter only of any description n exc 1Sqm all as specified and as directed. |
| 4 | Taking down shutter only of any description exc 1Sqm n. exc 2.0Sqm all as specified and as directed. |
| 5 | Taking down shutter only of any description exc 1Sqm n. exc 2 Sqm and refixing in same opening |
| 6 | S&F Powder coated aluminium frame for door, windows and ventilators with one or more rebates including necessary joining cleat, glazing clips, rubber packing, beading ,plaster work on edges during fixing (if required)etc complete all as specified and directed. |
| 7 | S&F 4mm thick Sheet glass, ordinary quality and glazing with glazing clip and powder coated aluminium beading in square n exc 0.5 sq. m in each panel |
| 8 | S&F Stainless steel wire cloth 0.36mm nominal dia wire and average width of aperture 1.40 mm and fixed with matching beading complete all as specified and directed. |
| 9 | S & F Pressed steel frames(105 X 60) for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified |
| 10 | S&F Pressed steel frames(125 X 60) for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified |
| 11 | S&F Factory made 18 mm thick PVC sheet both side pre laminated cabinet shutter of minimum density 600 Kg/cum bent at 90 degree and finished all edges at all levels, for providing edge lipping/beading or 1 mm thick PVC Sheet at all four edges using bonding tape etc. complete all as specified and directed |
| 12 | S&F full overlay soft close hinges 4\\" wide suitable for 18mm thick cupboard shutters complete all as specified and directed |
| 13 | S&F stainless steelhandles decorative type of 75 mm size all as specified and directed |
| 14 | M&L for 35mm thick 2nd class hardwood glazed and skeleton shutter open rebeted and prepared to receive glass, gauze etc (without slash bar ) edges of framing plain chamfered or rounded filled with cut and mitred beads for securing, glass etc size of member of shutter as per specified in SSR Part-I section 8,clause 8.24(a) supplied and fitted to chowkats and as directed by Engg. In Charge. |
| 15 | M&L Factory made flush shutters 35mm thick solid core construction, with block board core and plywood face panels, commercial type on both sides as in shutter all as specified and as directed. |
| 16 | M&L Factory made flush shutters 18-20mm thick solid core construction, with block board core and plywood face panels, commercial type on both sides as in CB shutter as in shutter all as specified and as directed.. |
| 17 | Supply and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminte shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame., all as per directions of Engineer-in-charge |
| 18 | Supply and fixing to 30 mm thick Glass Fibre Reinforced Plastic (FRP) panelled door shutter of required colour and approved brand and manufacture, made with fire - retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate for forming hollow rails and styles, with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast monolithically with 5 mm thick FRP laminate for panels conforming to IS: 14856, including fixing and as per directions of Engineer- in-charge.frames |
| 19 | S&F for 75mm long butt hinges, medium weight , cold rolled mild steel and fixed |
| 20 | S&F for 100mm long butt hinges, medium weight , cold rolled mild steel and fixed |
| 21 | S&F aluminium anodied 150mm long tower bolt of exteded section all as directed. |
| 22 | S&F aluminium alloy anodized sliding door bolt with laps and staple (bolt type) and fixing clip of sheet cast or extruted section or cast aluminium alloy and fixed length of bolt 300mm. |
| 23 | S&F for 150mm long aluminium handle cast type anodized all as specified and as directed by Engineer-in-Charge. |
| 24 | S&F for 100 mm long aluminium anodized barrel tower bolts of extruded section and fixed. |
| 25 | S&F Hasp and staple,safety type aluminium anodized including bolt to hinge plate and fixed with screws 150 mm size complete all as specified and directed. |
| 26 | S&F door stopper of 150 mm size (ISI Marked) aluminum alloy body and tongue double legged anodized with hard draw steel spring over all length of cover plate fixed in floor complete all as specified and directed. |
| 27 | S&F 25 mm dia stainless steel curtain drapery rod decorative type cut to length and fixed complete all as specified and directed. |
| 28 | S&F brackets suitable for 25mm dia stainless steel curtain rod complete all as specified and directed. |
| 29 | S&F in repairs SS plate rack 0.63 mm thick of Size 31\\"x36\\"x10\\" in SS 304 grade all as speciifed & directed |
| 30 | Dismantling structural steel work including doors, gates ,grill but excluding framed truss etc. all as specified and as directed. |
| 31 | S&F for Framed work such as grills,gratings, etc.. with ends of bars shouldered and/or riveted,or forged into spikes; framed guard bars; barred iron doors;ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290. Gde-E-165 complete all as speciifed & directed |
| 32 | M&L Framed work ( Fe 290 gde E 165) as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and uides) and hanging; also fastening and fixing complete all as specified and as directed. |
| 33 | M&L for Mild steel, plain, black sheet 1.00 mm thick in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as require all as directed |
| 34 | Dismantling of floor hearth or wall tilling including cement mortar bedding (but not backing) including rubbish off the premises |
| 35 | M&L Non-skid coloured ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including for 20mm thick screed bed or bedding layer in CM 1:6 for laying floor finishes all as specified and directed. |
| 36 | M&L Non-skid coloured ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in vertical surfaces/skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including rendering of 10mm thick on fair faces of brick work or concrete surfaces in CM 1:4 to receive tiles etc on vertical surfaces of walls all as specified and directed. |
| 37 | M&L for Non-skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including for 20mm thick screed bed or bedding layer in CM 1:6 for laying floor finishes all as specified and directed. |
| 38 | M&L for Glazed ceramic coloured tiles in vertical surfaces 450x350x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match including rendering of 10mm thick on fair faces of brick work or concrete surfaces in CM 1:4 to receive tiles etc on vertical surfaces of walls all as specified and directed. |
| 39 | Demolition of concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed. |
| 40 | Demolition of stone slabs and tiles of any description, laid bedded and pointed in any mortar. |
| 41 | M&L 75mm thick & plain cement concrete 1:3:6 type C2 using 40mm graded stone aggregate as inPlinth protection finished even and fair without using extra cement incl necessary formwork all as speciifed & directed |
| 42 | M&L 20mm thick granite slab with fully rounded edges Table rubbed & polished as in cooking platform on front face fixed in CM 1:4 including pointing in white cement (1:2) cutting space for sink & gas pipe hole including for 20mm thick screed bed or bedding layer in CM 1:6 for laying all as specified and directed in Engineer -in -Charge. |
| 43 | M&L for Machine cut Pre polished kota stone slab flooring 20-25mm thick over and incl 15mm thick cement screed base in CM 1:4 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab in single piece as in window cill,stairscase etc. |
| 44 | Demolition of wall of brick and stone wall built in cement mortor incl all quoins, archs, pillars,etc all as specified and as directed. |
| 45 | M&L Brick work sub class B bricks, straight or curved on plan exc 6m mean radius built in CM 1:6 all as specified and as directed by Engineer-in-Charge |
| 46 | Demolition of cement concrete of any description and in any position not other wise describe all as speciifed & directed |
| 47 | M& L for providing water proofing treatment of sunken portion of WCs, bathroom etc. by applying cement slurry mixed with Acrylic based polymer modified cementitious composite compound coating of make as approved by E-in-C's Br by adding: (a) 15mm thick rendering CM (1:4) with Liquid water proofing compound 200ml per 50 Kg bag of cement on floor and wall, finishing the surface even and smooth without using extra cement . The surface shall then be cured and allowed to dry. (Note : Water proofing compound shall be measured and paid separatel) (b) First layer of slurry of cement @ 0.488 kg/sqm mixed with Acrylic based polymer modified cementitious composite compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hrs. (c) Second layer of slurry of cement @ 0.242 kg/sqm mixed with Acrylic based polylmer modified cementitious composite compund @ 0.126 kg/sqm. Provn of 40mm thick PCC 1:2:4 type b-1 as top layer, and provn of UPVC spout with 40mm dia upto 30cm with water tight joint from the external surface of wall and filled with PCC 1:5:10 type E2 as lean concrate up to required level as specifiedThis layer will be allowed to air cure for 4 hrs followed with water curing for 48 hrs including complete removal of old treatment to sunken portion etc complete all as specified and directed |
| 48 | Taking down cement plaster any description on brick or stone wall/ celling including raking out joint , haking for key scrubing with water etc. |
| 49 | M & L for 10 mm thick rendering in CM 1:6 on concrete surfaces / fair faces of brick masonary wall, finished even and smooth without extra cement |
| 50 | M & L for rendering 15 mm thick cement plaster in two layers (10+5) with bottom layer 10 mm th in CM 1:6 and top layer 05 mm thick in CM 1:4 mixed with water proof compound @ 3% by weight of cement or as per manufactures instructions finished even and smooth without using extra cement up to any height as directed by Engineer-in-Charge(Water proof compound measured and paid seperately) |
| 51 | M&L rendering 5mm thick on concrete surface of ceiling in CM 1:3 finishing the surface fair and even complete all as specified and directed. |
| 52 | M&L for preparation of old decorated surfaces plastered or unplastered on walls including cornices pilasters by brooming down or steel wire brushing, scraping down, smoke shoot, moulds, mors and efforescent salts and treating oil and greasy spots and applying one coat of white wash on walls upto 4th floor complete all as specified and directed by Engineer-in-Charge. |
| 53 | All as per item no. 56 above but one coat of white wash on ceiling complete all as specified and directed. |
| 54 | M & L for preparation of old painted surfaces of steel and iron surfaces over 10cm width or grith and applying one coat of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge. |
| 55 | M&L for preparation and Painting of new Steel Surfaces with two coat Synthetic Enamel Paint of any description, over 10cm in width or girth,not otherwise described over Red Oxide Primer all as speciifed & directed |
| 56 | M&L for filling surface cracks not exc 5 mm to 7 mm wide with \\"Dr fixit\\" cracks X power or equivalent polymer modified cracks filler comp and all as per manufacturer instructions and all as speciifed & directed |
| 57 | M&L Preparation of new wooden surface of any description not otherwise described over 10cm width or grith and applying two coats of synthetic enamel paint over one coat of pink primer. |
| 58 | M & L for three coat of white wash on new surfaces of ceiling including preparation of new surfaces by mechanical means using suitable tools and plants as per manufactures instructions and as directed by Engineer-in-Charge |
| 59 | Taking up or down steel tubing pipe and connections 15mm bore and connections all as specified |
| 60 | Taking up or down steel tubing pipe and connections 20mm bore and connections all as specified |
| 61 | S&F 15mm dia tubes ‘Medium grade’ galvanized with all fittings and fixed complete to walls and ceiling or laid in floors all as specified |
| 62 | ditto as above but fixing only . |
| 63 | S&F 20mm dia tubes ‘Medium grade’ galvanized with all fittings and fixed complete to walls and ceiling or laid in floors, |
| 64 | ditto as above but fixing only . |
| 65 | Dismantling water tanks exc 500 but n.exc 1000 Litres capacity as directed |
| 66 | S&F 1000 litres capacity rotational moulded polyethylene water storage tank white coloured (triple layers) (cylindrical vertical with closed top), hoisted and fixed in position all as specified in SSR Part-I, connecting up pipes including 20 mm bore plastic ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic plastic ball screwed for iron pipe and fixed. (Minimum weight of ball valve - 210 gms) with Climate protective water thermal tank cover/Jacket for Hot & Cold Wheather for 1000Ltr water tank. The cover should be environment friendly made with 5 layers heavy duty Nylon velcro straps belt for tighten the tank and made of supportive forming technology. as specified and directed as directed by Engineer-in-Charge |
| 67 | S&F 20 mm PTMT ball valves,high pressure,with screwed for iron pipe and fixed. |
| 68 | S & F in repair sink with drainage board made out of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mmx460mm bowl size 410mmx330mmx160mm complete all as specified and directed. |
| 69 | S&F in repairs vitreous china Table top wash basin size 550 x 440 with 20mm thick granite of size 0.70 x 0.60 countor including cutting for and pinning in ends of galvanied iron bracket”wash basin, PVC waste pipe of 32mm bore and of suitable length fixed in 50mm pvc pipe in wall upto grating for esthetic view,complete all as specified and as directed by Engineer-in-Charge |
| 70 | S&F in repairs EWC vitreous china wash down water closet pan (pedestal pattern), white, with and including plastic water closet seat, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device incl jet spray fixed complete all as specified and as directed by Engineer-in-Charge |
| 71 | S & F in repair PVC valveless, syphonic action type, flushing cistern, low level, white with inlet ball valve foat and handle including brackets 10 litres complete all as specified and as directed. |
| 72 | S&F in repair 15 mm dia Brass CP, wall mixer 3 in 1 system with provision for both hand and overhead shower complete with 115 mm long bend pipe, connecting legs and wall flange (without Hand and overhead shower) (Concealed type) screwed both ends for iron pipe or for unions complete all as specified and as directed. |
| 73 | S&F in repair chromium plated Brass basin central hole mixer for mixing hot & cold water, screwed down for iron pipe and fixed complete all as specified and directed. |
| 74 | S&F 15 mm dia bore Toilet hand shower (Health Faucet) with 8 mm dia and 1.00 mtr long flexible tube and wall hook complete all as directed. |
| 75 | M&L for 15 mm dia brass CP two way Bib cock with wall flange concealed type screwed down for iron pipe or for unions complete all as directed. |
| 76 | S&F CP towel rail 600 mm long complete all as directed. |
| 77 | S&F Fancy type chromium plated towel rack 600mm long without lower hanger but with 3 hooks fitted complete all as specified. |
| 78 | S&F chromium plated toilet paper holder with flap complete all as directed. |
| 79 | S&F Stainless steel shelf with decorative and ornamental side supports and front lining of chromium plated fixed with screws and glass with glass as shelf supported over frames all as specified and all as directed. |
| 80 | S & F Soap dish, any type, fixed to plugs with chromium plated brass screws. |
| 81 | S&F corner Stainless steel self of size 9''x9'' self and front circle in design fixed over chromium plated brackets of heavy duty with front linings with glass fixed in the walls with necessary screws etc. all specified and as directed. |
| 82 | S & F in repair for 15 mm bore Chromium plated fancy type Bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as directed. |
| 83 | S & F in repair 15 mm dia Fancy type Chromium plated Angle valves, cast copper alloy screwed down high pressure, with crutch or butterfl y handle, screwed both ends for iron pipe or for unions complete all as directed. |
| 84 | S & F in repair for Gun-metal, globe or gate valves, with iron wheel head, screwd both end sor iron pipe and fixed 20 mm dia complete all as specified and directed. |
| 85 | S & F in repair PVC connection pipe 15mm dia with PTMT nuts of length 450mm complete all as directed. |
| 86 | S & F in repair 450mm long CP brass connection pipe with CP brass nuts on both ends for fixing to pipe or other fittings complete all as specified. |
| 87 | S&F in repair brass Chromium plated shower roses of 125mm size with swivel joints including fixing to steel pipe or union complete all as specified and directed |
| 88 | Supply and fixing in repair 600mmx450mm bevelled edge mirror of selected quality glass, with chromium plated brass screws and cup washers |
| 89 | S&F in repairs 110mm dia (SWR) pipes single socketed in any length with rubber joints fixed to wall or floor with clamps complete all as specified and directed. |
| 90 | S&F in repairs 75mm dia (SWR) pipes single socketed in any length with rubber joints fixed to wall with clamps complete all as specified and directed. |
| 91 | S&F 110 mm dia PVC (SWR) bends complete all as specified and directed. |
| 92 | S&F 75mm dia PVC (SWR) bends complete all as specified and directed. |
| 93 | S&F 110 mm dia PVC (SWR) branch piece, single (single Y) equal or unequal with access door complete all as specified and directed. |
| 94 | S&F 75 mm dia PVC (SWR) Junction single T equal or unequal complete all as specified and directed. |
| 95 | S&F 110 mm dia PVC (SWR) Junction single T equal or unequal complete all as specified and directed. |
| 96 | S&F 75 mm dia PVC (SWR) Couplers complete all as specified and directed. |
| 97 | S&F 110 mm dia PVC (SWR) Couplers complete all as specified and directed. |
| 98 | S&F 110mm dia PVC (SWR) vent cowl complete all as specified and directed. |
| 99 | M&L in PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement.complete all as specified directed. |
| 100 | S & F stack clamp made of 50 mm X 5 mm flat iron and 16 mm dia round iron stay including nut bolts and securing ends of stay to wall or roof suitable for 100 mm bore pipe complete all as specified and directed. |
| 101 | S&F in repairs 75mm dia PVC (SWR) floor trap plain with gratings including jointing with solvent cement complete all as specified and directed. |
| 102 | M&L PCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in roof padding (average thikness 50mm thick) complete as directed by Engineer-in-Charge |
| 103 | M&L for providing cement concrete type B1, 1:2:4 using 20 mm graded aggregate in cover fillet of 75 mm radius at junction of roof slab and parapet wall etc complete all as specified and directed by Engineer-in-Charge. |
| 104 | Demolition of any old unserviceable roof treatment of any description including roof tiles/ padding etc.to expose the RCC Slab of roof, cleaning,washing & rubbing all as specified and directed. |
| 105 | M&L for applying cold bituminous primer @ 0.30 Ltr / Sqm conforming to IS 3384 laying APP polymer modified membrane 3mm thick minimum 3.5 Kg/Sqm in weight with non-woven polyster reinforcement with plain finish and sealing all overlaps of 150 mm in length side and 100 mm on width side of membrane by torching the same as per manufactures instruction and all as per specified including application of solar reflective aluminum paint all as specified and directed by Engr-in Charge |
| 106 | M&L10mm thick screed bed in CM 1:4 mixed with WPT 3% by weight of cement all as specified and as directyed by Engr-in-Charge. |
| 107 | Supply only intergral water proofing compound. |
| 108 | M& L for ATT at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same all as speciifed & directed |
| 109 | Treatment of soil under existing floors using emulsion @ one litre per hole,300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified and directed. |
| 110 | Excavation in trenches not exc.1.50m wide and not exc 1.5m deep getting out in soft/loose soil all as speciifed & directed |
| 111 | M&L for concrete bedding to drain pipes including packing under, and haunching in PCC 1:3:6 type C2 using 40 mm graded aggregate against the side of 150mm dia RCC pipes after they are laid and tested all as specified and directed. |
| 112 | M&L for 150 mm bore Reinforced concrete pipe class NP3, laid and jointed complete with collars all as specified and directed. |
| 113 | Returning filling in including spreading,levelling,watering and well ramming in layers n.exc 25 cm . |
| 114 | Removing excavated materials not exc. 50m and depositing where directed. |
| 115 | M&L for providing plain cement concrete 1:4:8 type D-2 (using 40mm graded aggregate)as in foundation filling and mass concrete all as directed. |
| 116 | Demolition of cement concrete of any description and in any position complete all as specified. |
| 117 | S&F MS steel TMT bars 10mm dia and over cut including 10mm dia cut to length ,bent to shaprequired including cranking bending for hooping for column ,hooking ends and bindings with and including mild steel wire (annealel)not less than 0.9mm dia. |
| 118 | M&L for providing precast cement concrete 1:2:4 type B-1 (using 20mm graded aggregate) set in cement mortar 1:4 as in cover slab supported on wall complete all as specified and directed |
| 119 | M&L cement concrete Type B1 1:2:4 ( 20 mm graded aggregate) as in coping all as directed. |
| 120 | S&F stainless steel peg set of five hooks as approved by GE and as specified and directed. |
| 121 | Complete removal of existing treatment on wall/ roof projections including facia, cornices etc by scrapping with mechanical sander (having machanical vaccum mechanism) with sanding pad of appropriate grit to make surface clean, free from dust, loose paint etc by skilled labour complete all as specified and directed. |
| 122 | Note : Sanding of surface to be done by mechanical sander with 1500-2700 rpm, with internal dust extraction system for clean environment certified by paint manufacturer. Proper masking to be carried out before primer and paint application. as specified and directed |
| 123 | Material and labour for waterproof cement based putty @ 1 Kg (undiluted) per Sq Mtr of average thickness 1mm to 1.5mm thick over the plastered /oldpainted wall after scrapping to prepare the surface with mechanical wall sander (having mechnical vacuum mechanism) having RPM not less than 1500, sanding pad of 240 Grit or above to make the surface free from dust etc. by skilled labour as per following steps :- Step 1) Mix the putty powder by adding water as per manufacturer instructions and mix it with putty mixer with the mixing capacity of min 2.5 kg putty per minute. Step 2) Apply the first coat the prepared mixer with the help of fully automatic airless spray machine of putty application having flow speed of max 6 ltrs per minutes with a maximum pressure 3300 PSI. Step 3) Allow 6-8 hrs time to dry the putty surface. |
| 124 | Material and labour for applying two coats of oil bound distemper using Airless spray technology with max working pressure of 3300 PSI and capable of operating single spray gun with a max material hose length of 30 mtr the spray machine should be of reputed manufacturer with pro guard technology and capability of tracking pressure and paint usage and certified by paint manufacturer and as mentioned in PS and accessories for applying distemper should be able to spray in hard to reach areas and penetration of distemper on the surface complete all as specified and directed. |
| 125 | M& L for one coat of acrylic water based exterior grade primer @ 0.9 liter (undiluted)/ 10 Sqm diluted with wtaer in 1:1 ratio to be applied with fully auomatic airless spray machine and llow 6-8 hours to dry the surface for painting of subsequent coats complete all as specified and directed. |
| 126 | Material and labour for two coats of water based permium acrylic smooth exterior emulsion of approved colour with silicon additive & Color stay Technology, Excellent Dirt Pick up resistance with low VOC less than 50 gram / litre as per the LEEDS specifications, Anti Algal properties in two coats not less than 1.79 ltr (undiluted)/ 10 sqm diluted with water as per manufacturer instructions applied over priming coat with fully automatic airless spray machine of paint application with a flow speed of min 1 ltr per minute having a pressure of 3300 PSI. Allow 6-8 hrs to dry the surface in both the coats of paint complete all as specified and directed. |
| 127 | Taking down carefully point wiring including (Light fan, Socket or power complete fittings, such as switches, ceiling roises, pendant holders, Batten holders, shades conical fan regulators, light or power socket etc) removing material from site and making good disturbed surfaces of walls roofs etc all as directed. |
| 128 | Taking down carefully sub main wiring complete including removing materials from site and making good disturbed surfaces of walls roofs etc all as directed. |
| 129 | M&L for point wiring complete as specifieid with 1100 volt grade 1.5 sq.mm ( nominal area) single core PVC insulated unsheathed (FRLS) cable multi-stranded copper conductor drawn through and including rigid non-metallic PVC conceated conduit of suitable size but not less than 20mm dia, with all fittings, concealed in wall/roof/floor including decorative modular cover plates (inner and outer) suitable for houising modular patytern switches/sockets/regulators etc. along with necessary metal boxes flush mounting in the wall duly earthed with same cable as for wiring above but green in color as continuous earthing wire complete all as specified for :- |
| 130 | One Light point controlled by one one/way switch |
| 131 | One Light point controlled by one one/way switch |
| 132 | One 3 pin 5 Amps socket outlet on same board with other switch. |
| 133 | One 3 pin 5 Amps socket outlet on independent board with other switch. |
| 134 | One bell point controlled by one one/way switch |
| 135 | One light point controlled by one one/way switch |
| 136 | all as per item No. 2 above but wiring with 2.5sqmm multistarnded copper conductor unsheathered and 2.5 sqmm copper conductor unsheathered cable as earth continuity conductor for one 5 pin 15 Amps power socket outlet point on independent board/400 watt flood light. |
| 137 | M&L for Sub main wiring complete with two run of 6 Sqmm single core, PVC insulated but unsheathed, multistranded copper conductor FR 1100 Volts grade cable drawn through in and including non metallic, rigid etc. PVC insulated but unsheathed multistandard copper conductor FR 1100 Volts grade cable as earth continuity wire and connected to earth dolly . Note :- Two run of 6 Sqmm cable one run of earth wire and PVC conduit and its accessories shall be measured and paid as one length. |
| 138 | M&L for Sub main wiring complete with two run of 4 Sqmm single core, PVC insulated but unsheathed, multistranded copper conductor FR 1100 Volts grade cable drawn through in and including non metallic, rigid etc. PVC insulated but unsheathed multistandard copper conductor FR 1100 Volts grade cable as earth continuity wire and connected to earth dolly . Note :- Two run of 4 Sqmm cable one run of earth wire and PVC conduit and its accessories shall be measured and paid as one length. |
| 139 | S&F Modular switch 1 way 6A, 1 module complete all as specified and directed. |
| 140 | S&F Modular switch 1 way 16A, 1 module complete all as specified and directed. |
| 141 | S&F Modular Bell Push 1 way 6A, 1 module complete all as specified and directed. |
| 142 | S&F Modular switch 2 way 6A, 1 module complete all as specified and directed. |
| 143 | S&F socket, 6 A-2/3 pin combined Modular 2 module complete all as specified and directed. |
| 144 | S&F socket, 6 A/16A-2/3 pin combined Modular 2 module complete all as specified and directed. |
| 145 | S&F ceiling rose surface bakelite three terminal 250/230 volts ISI marked complete all as specified and directed. |
| 146 | S&F Fan top regulator, 120W- 2 module complete all as specified and directed. |
| 147 | S&F in DB's sheet metal double door enclosure for SPN DB 12 way type 240 volts and 200 amp ratings bus bar complete all as specified and directed. |
| 148 | Supply and fixing amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified and directed. |
| 149 | MCB SP up to 32 Amp, 240 volts |
| 150 | MCB SPN up to 63 Amp, 240 volts |
| 151 | Supply and fixing LED Tube light fitting ENERGY Efficient 20 Watt 2000 lumen bright light including taking down old fitting complete all as specified and directed by Engr-in-charge. |
| 152 | Supply and fixing LED Tube light fitting ENERGY Efficient 10 Watt 2000 lumen bright light including taking down old fitting complete all as specified and directed by Engr-in-charge. |
| 153 | Supply and fixing wall mounted light fitting suitable for retrofit LED lamp upto 14 watt B22 with lamp champagne gold finish fixture with plastic body, Opal white PC diffuser for glare free light complete complete all as specified and directed by Engr-in-charge. |
| 154 | Taking down carefully unserviceable Exhaust fan of any make and sweep and dismantling blades of any sweep/make and reassembling and re-fixing the fan after repairing /replacing complete for smooth functioning all as specified and directed. |
| 155 | S&F exhaust fan steel body AC single phase 230/240V of size 300 mm sweep with blade & frame and louvers as specified and directed. |
| 156 | M&L for making hole for exhaust for 300 mm dia in existing wall and making good the damage surface all as directed. |
| 157 | Taking down old water heater safely from existing site any cap and depopsited in MES store to concern authority completed all as specified and directed. |
| 158 | S&F electric water heater 25 Ltr single phase steel body copper inner tank heating element up to 2 KW BEE 5 star rated complete with all accessories safty valve, themostate, NRV, connection pipe complete all as specified and directed. |
| 159 | Taking down carefully unserviceable ceiling fan of any make and sweep and dismantling blades of any sweep/make and reassembling and re-fixing the fan after repairing /replacing complete for smooth functioning all as specified and directed. |
| 160 | S&F ceiling fan 1200mm sweep with blades, down rods, electronic regulator and accessories single phase min air delivery 210 CFM with service valve 6 BEE 5 star rated brushless direct current motor BLDC as specified and directed. |
| 161 | S&F in repairs LED Roadway Lighting Luminaries type LED 1X25 W,Endura citylite 25 W,new generation energy saving & environment friendly long life versatile pressure die-cast aluminium IP65 roadway luminaire high power LED as light source and accessories and connecting up to ceiling rose and fittings with 3 core , 1.5 Sqmm PVC insulated copper conductor cable including fixing arrangement comprising of 25 mm dia GI pipe light grade 1.2 mtr long bend at 120 degree fixed to wall with help of 2 Nos, clamp made of flat iron 50 x 6 mm and necessary nut, bolt and washer complete. Make : Cat No LHEWDRP7PN1W025 of Havells or equivalent of Bajaj/Philips/CG/HPL/GE/ORIENT |
| 162 | Supply and fix bracket security light made up of 25 mm dia, 1.0 mtr long GI pipe, light grade, bentto required length, fixed to wall either 2 clamps made off 20x3 mm mild steel flat min 15 cm long, 4 noss 8mm dia bolts with nut complete including taking down old unserviciable all as specified and directed |
| 163 | S & F buzzer ding dong AC 230 volt all as specified and directed. |
| 164 | S & F Single pole and neutral enclosure with a two pin and earth plug and socket complete with one 20 A single pole MCB all as specified and directed. |
| 165 | M&L for earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm burried directly in ground level with top edge of earth plate at a depth not less than 2.25 m below ground level connected to and including galvanised earh lead wire 4 mm dia by means of bolts, nuts, check nuts and washers etc made of GI and connected to earthing test point all as shown in plate No 3 of SSR indicted and testing on completion including excavation and earth work in any type of soil/rock, PCC (1:3:6) type C-1 earthing chamber, precast RCC slab 40 mm thick reinforced with 6 mm dia MS bar 3 Nos both way with handle made out of 6 mm dia MS bar water pipe with ire mesh and connecting testing etc complete all as specified and directed. M&L for point wiring complete as specifieid with 1100 vo;t grade 1.5 sq.mm ( nominal area) single core PVC insulated unsheathed (FRLS) cable multi-stranded copper conductor drawn through and including rigid non-metallic PVC conceated conduit of suitable size but not less than 20mm dia, with all fittings, concealed in wall/roof/floor including decorative modular cover plates (inner and outer) suitable for houising modular patytern switches/sockets/regulators etc. along with necessary metal boxes flush mounting in the wall duly earthed with same cable as for wiring above but green in color as continuous earthing wire complete all as specified for :- One Light point controlled by one one/way switch 95.0 Point One Light point controlled by one one/way switch 35.0 Point One 3 pin 5 Amps socket outlet on same board with other switch. 40.0 Point One 3 pin 5 Amps socket outlet on independent board with other switch. 25.0 Point One bell point controlled by one one/way switch 5.0 Point One light point controlled by one one/way switch 3.0 Point all as per item No. 2 above but wiring with 2.5sqmm multistarnded copper conductor unsheathered and 2.5 sqmm copper conductor unsheathered cable as earth continuity conductor for one 5 pin 15 Amps power socket outlet point on independent board/400 watt flood light. 15.0 Point M&L for Sub main wiring complete with two run of 6 Sqmm single core, PVC insulated but unsheathed, multistranded copper conductor FR 1100 Volts grade cable drawn through in and including non metallic, rigid etc. PVC insulated but unsheathed multistandard copper conductor FR 1100 Volts grade cable as earth continuity wire and connected to earth dolly . Note :- Two run of 6 Sqmm cable one run of earth wire and PVC conduit and its accessories shall be measured and paid as one length. 150.0 RM M&L for Sub main wiring complete with two run of 4 Sqmm single core, PVC insulated but unsheathed, multistranded copper conductor FR 1100 Volts grade cable drawn through in and including non metallic, rigid etc. PVC insulated but unsheathed multistandard copper conductor FR 1100 Volts grade cable as earth continuity wire and connected to earth dolly . Note :- Two run of 4 Sqmm cable one run of earth wire and PVC conduit and its accessories shall be measured and paid as one length. 100.0 RM S&F Modular switch 1 way 6A, 1 module complete all as specified and directed. 195.0 EACH S&F Modular switch 1 way 16A, 1 module complete all as specified and directed. 15.0 EACH S&F Modular Bell Push 1 way 6A, 1 module complete all as specified and directed. 5.0 EACH S&F Modular switch 2 way 6A, 1 module complete all as specified and directed. 6.0 EACH S&F socket, 6 A-2/3 pin combined Modular 2 module complete all as specified and directed. 65.0 EACH S&F socket, 6 A/16A-2/3 pin combined Modular 2 module complete all as specified and directed. 15.0 EACH S&F ceiling rose surface bakelite three terminal 250/230 volts ISI marked complete all as specified and directed. 130.0 EACH S&F Fan top regulator, 120W- 2 module complete all as specified and directed. 20.0 EACH S&F in DB's sheet metal double door enclosure for SPN DB 12 way type 240 volts and 200 amp ratings bus bar complete all as specified and directed. 5.0 EACH Supply and fixing amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified and directed. MCB SP up to 32 Amp, 240 volts 50.0 EACH MCB SPN up to 63 Amp, 240 volts 5.0 EACH Supply and fixing LED Tube light fitting ENERGY Efficient 20 Watt 2000 lumen bright light including taking down old fitting complete all as specified and directed by Engr-in-charge. 61.0 EACH Supply and fixing LED Tube light fitting ENERGY Efficient 10 Watt 2000 lumen bright light including taking down old fitting complete all as specified and directed by Engr-in-charge. 10.0 EACH Supply and fixing wall mounted light fitting suitable for retrofit LED lamp upto 14 watt B22 with lamp champagne gold finish fixture with plastic body, Opal white PC diffuser for glare free light complete complete all as specified and directed by Engr-in-charge. 20.0 EACH Taking down carefully unserviceable Exhaust fan of any make and sweep and dismantling blades of any sweep/make and reassembling and re-fixing the fan after repairing /replacing complete for smooth functioning all as specified and directed. 10.0 EACH S&F exhaust fan steel body AC single phase 230/240V of size 300 mm sweep with blade & frame and louvers as specified and directed. 15.0 EACH M&L for making hole for exhaust for 300 mm dia in existing wall and making good the damage surface all as directed. 5.0 EACH Taking down old water heater safely from existing site any cap and depopsited in MES store to concern authority completed all as specified and directed. 5.0 EACH S&F electric water heater 25 Ltr single phase steel body copper inner tank heating element up to 2 KW BEE 5 star rated complete with all accessories safty valve, themostate, NRV, connection pipe complete all as specified and directed. 5.0 EACH Taking down carefully unserviceable ceiling fan of any make and sweep and dismantling blades of any sweep/make and reassembling and re-fixing the fan after repairing /replacing complete for smooth functioning all as specified and directed. 20.0 EACH S&F ceiling fan 1200mm sweep with blades, down rods, electronic regulator and accessories single phase min air delivery 210 CFM with service valve 6 BEE 5 star rated brushless direct current motor BLDC as specified and directed. 20.0 EACH S&F in repairs LED Roadway Lighting Luminaries type LED 1X25 W,Endura citylite 25 W,new generation energy saving & environment friendly long life versatile pressure die-cast aluminium IP65 roadway luminaire high power LED as light source and accessories and connecting up to ceiling rose and fittings with 3 core , 1.5 Sqmm PVC insulated copper conductor cable including fixing arrangement comprising of 25 mm dia GI pipe light grade 1.2 mtr long bend at 120 degree fixed to wall with help of 2 Nos, clamp made of flat iron 50 x 6 mm and necessary nut, bolt and washer complete. Make : Cat No LHEWDRP7PN1W025 of Havells or equivalent of Bajaj/Philips/CG/HPL/GE/ORIENT 2.0 EACH Supply and fix bracket security light made up of 25 mm dia, 1.0 mtr long GI pipe, light grade, bentto required length, fixed to wall either 2 clamps made off 20x3 mm mild steel flat min 15 cm long, 4 noss 8mm dia bolts with nut complete including taking down old unserviciable all as specified and directed 2.0 EACH S & F buzzer ding dong AC 230 volt all as specified and directed. 5.0 EACH S & F Single pole and neutral enclosure with a two pin and earth plug and socket complete with one 20 A single pole MCB all as specified and directed. 10.0 EACH M&L for earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm burried directly in ground level with top edge of earth plate at a depth not less than 2.25 m below ground level connected to and including galvanised earh lead wire 4 mm dia by means of bolts, nuts, check nuts and washers etc made of GI and connected to earthing test point all as shown in plate No 3 of SSR indicted and testing on completion including excavation and earth work in any type of soil/rock, PCC (1:3:6) type C-1 earthing chamber, precast RCC slab 40 mm thick reinforced with 6 mm dia MS bar 3 Nos both way with handle made out of 6 mm dia MS bar water pipe with ire mesh and connecting testing etc complete all as specified and directed. 2.0 EACH EACH EACH EACH EACH EACH EACH EACH EACH EACH EACH EACH EACH EACH EACH EACH EACH EACH EACH EACH EACH EACH EACH EACH EACH EACH EACH EACH EACH Please Enable Macros to View BoQ information |
