Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | Boring, providing and installation bored cast-in-situ reinforced cement concrete piles of grade M-25 of specified diameter and length below the pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. by percussion drilling using Direct mud circulation (DMC) or Bailer and chisel technique by tripod and mechanical Winch Machine all complete, including removal of excavated earth with all its lifts and leads (length of pile for payment shall be measured up to bottom of pile cap).500 mm dia piles |
| 2 | EARTH WORK :Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and for all lift, as directed by Engineer-in-charge.All kinds of soil. |
| 3 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 and for all lift. |
| 4 | Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. |
| 5 | Surface dressing of the ground including removing vegetation and in equalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m. |
| 6 | CEMENT CONCRETE (CAST IN SITU)Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 7 | Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 20mm nominal size). |
| 8 | Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer’s specification. |
| 9 | Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75 mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. |
| 10 | Providing and laying in position ready mixed or site batched design mix cement concrete for plain cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana/Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard settingof concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering and finishing as per direction of the engineer-in-charge; for the following grades of concrete.Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the minimum specified cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.All works upto plinth level :Concrete of M20 grade with minimum cement content of 270 kg /cum |
| 11 | DESIGN MIX CONCRETE:Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge, for the followinggrades of concrete.:Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.(a) All works upto plinth level.Concrete of M25 grade with minimum cement content of 330 kg /cum |
| 12 | (b) All works above plinth level upto floor V levelConcrete of M25 grade with minimum cement content of 330 kg /cum |
| 13 | FORM WORKCentering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete |
| 14 | Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc. |
| 15 | Suspended floors, roofs, landings, balconies and access platform |
| 16 | Lintels, beams, plinth beams, girders, bressumers and cantilevers |
| 17 | Columns, Pillars, Piers, Abutments, Posts and Struts |
| 18 | Stairs, (excluding landings) except spiral-staircases |
| 19 | STEEL REINFORCEMENTSteel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 20 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 21 | MASONRY WORKBrick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:Cement mortar 1:4 (1 cement : 4 coarse sand) |
| 22 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand) |
| 23 | Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth.Granite Stone of approved shade |
| 24 | Providing and fixing ISI marked flush door shutters conforming to IS :2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws |
| 25 | Extra for providing vision panel not exceeding 0.1 sqm in all type of flushdoors (cost of glass excluded) (overall area of door shutter to bemeasured):Rectangular or square |
| 26 | MISCELLANEOUS-WOOD WORKProviding and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete :2nd class teak wood.50x12 mm |
| 27 | Providing and fixing chromium plated brass curtain rod having wall thickness of 1.25 mm with two chromium plated brass brackets fixed with C.P. brass screws and PVC sleeves etc., wherever necessary complete :20 mm dia |
| 28 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to openings /wooden frames with rawl plugs screws etc. |
| 29 | Providing 40x5 mm flat iron hold fast 400 mm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 300x100x150 mm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size). |
| 30 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :250x10mm |
| 31 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :150x10mm |
| 32 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :125 mm |
| 33 | Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.Single rubber stopper |
| 34 | Providing and fixing bright finished brass 100 mm mortice latch and lock, ISI marked, with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868) aluminium lever handles of approved quality with necessary screws etc. complete. |
| 35 | Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.Two track two panels sliding window made of (big series) frame 67 x 50 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension . (Area of window above 1.75 sqm upto 2.50 sqm). |
| 36 | Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm). |
| 37 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes |
| 38 | Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing. |
| 39 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.) |
| 40 | Providing & fixing fly proof wire gauze to windows, clerestory windows & doors with M.S. Flat 15x3 mm and nuts & bolts complete.Stainless steel (grade 304) wire gauze of 0.5 mm dia wire and 1.4 mm aperture on both sides |
| 41 | CERAMIC GLAZED TILESProviding and fixing 1st quality ceramic glazed floor tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete. |
| 42 | VITRIFIED FLOOR TILESProviding and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 800 x 800 mm |
| 43 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion,(i) Single socketed pipes.110 mm diameter |
| 44 | Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.Coupler110mm |
| 45 | Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.Bend 87.5°110mm bend. |
| 46 | Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.Shoe (Plain)110mm Shoe |
| 47 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.110mm |
| 48 | Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams. |
| 49 | Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main “T” runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross “T” of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main “T” at 600 mm center to center to form a grid of 1200x600 mm and secondary cross “T” of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main “T” runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. 12.5 mm thick square edge PVC Laminated Gypsum Tile of size 595x595 mm, made of Gypsum plasterboard, manufactured from natural gypsum as per IS 2095 part I and laminated with white 0.16 mm thick fire retardant PVC film on the face side and 12 micron metalized polyester on the back side with all edges sealed with the face side PVC film which goes around and wraps the edges and is bonded to the edges and the back side metalized polyester film so as to make the tile a completely sealed unit. |
| 50 | Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (bothside inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at1200 mm centre to centre, one flange fixed to the ceiling with dashfastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flangeof cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre,shall be fixed in a direction perpendicular to G.I. intermediate channelwith connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :12.5 mm thick tapered edge gypsum moisture resistant board |
| 51 | FINISHINGCEMENT PLASTER (IN FINE SAND)12 mm cement plaster of mix :1:4 (1 cement: 4 fine sand) |
| 52 | 15 mm cement plaster on the rough side of single or half brick wall of mix :1:4 (1 cement: 4 fine sand) |
| 53 | CEMENT PLASTER WITH A FLOATING COAT OF NEAT CEMENT12 mm cement plaster finished with a floating coat of neat cement of mix :1:3 (1 cement: 3 fine sand) |
| 54 | 6MM CEMENT PLASTER6mm Cement plaster of mix.1:3 (1 cement : 3 fine sand) |
| 55 | Neat cement punning. |
| 56 | Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer and of required shade and colour all complete to achieve even shade and colour :New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litre |
| 57 | EXTERIOR FINISHING :Finishing walls with Acrylic Smooth exterior paint of required shade :New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm) |
| 58 | With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works |
| 59 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :Two or more coats on new work |
| 60 | French spirit polishing :Two or more coats on new works including a coat of wood filler |
| 61 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 62 | Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour.Two coats |
| 63 | Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content.With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre |
| 64 | Dry brick pitching half brick thick including supply of bricks and preparing the surface complete :With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 65 | ALUMINIUM WORKProviding and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :(Glazing, paneling and dash fasteners to be paid for separately) :For fixed portion.Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 66 | Grading roof for water proofing treatment withCement concrete 1:2:4 (1 cement : 2 coarse sand :4 graded stone aggregate 20mm nominal size) |
| 67 | Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of:(i) Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface.(ii) IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface.(iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area.(iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm). |
| 68 | Providing and applying fibre reinforced elastomeric liquid water proofing membrane with resilient acrylic polymers having Sun Reflectivity Index (SRI) of 105 on top of concrete roof in three coats @10.76 litre/ 10 sqm. One coat of self-priming of elastomeric waterproofing liquid (dilution with water in the ratio of 3:1) and two coats of undiluted elastomeric waterproofing liquid (dry film thickness of complete application/system not less than 500 microns). The operation shall be carried out after scrapping and properly cleaning the surface to remove loose particles with wire brushes, complete in all respect as per the direction of Engineerin-Charge. |
| 69 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/Ceosetory windows & other Frames/Chowkhat comprising of virgin PVC polymer of K value 58- 60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threadedstar headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately).Note: For WPC solid door/window frames, minus 5mm tolerance in dimensions i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.Frame size 65 x 150 mm |
| 70 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/ borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately)30 mm thick |
| 71 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests |
| 72 | Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required :W.C. pan with ISI marked white solid plastic seat and lid |
| 73 | Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required :Single half stall urinal with 5 litre P.V.C. automatic flushing cistern. |
| 74 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap |
| 75 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :Kitchen sink with drain board510x1040 mm bowl depth 250 mm |
| 76 | Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge. |
| 77 | Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge. |
| 78 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.Flexible pipe32 mm dia |
| 79 | Providing and fixing 100 mm sand cast Iron grating for gully trap. |
| 80 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 81 | Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete. |
| 82 | Providing and fixing toilet paper holder :C.P. brass |
| 83 | Providing and fixing M.S. stays and clamps for sand cast iron/ centrifugally cast (spun) iron pipes of diameter :100 mm |
| 84 | Providing and fixing M.S. stays and clamps for sand cast iron/ centrifugally cast (spun) iron pipes of diameter :75 mm |
| 85 | Providing and fixing Polyethelene-Aluminium- Polyethelene PE-AL-PE Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with trenching, refilling and testing of joints complete as per direction of the engineer in charge.External work2025 (25 mm OD ) pipe |
| 86 | Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors :100 mm inlet and 100 mm outletSand cast iron S&S as per IS: 3989 |
| 87 | Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors :100 mm inlet and 75 mm outletSand cast iron S&S as per IS - 3989 |
| 88 | Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. |
| 89 | Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms. |
| 90 | C.P.V.C. PIPESProviding and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.Internal work - Exposed on wall.15 mm nominal outer dia Pipes |
| 91 | C.P.V.C. PIPESProviding and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.Internal work - Exposed on wall.20 mm nominal outer dia Pipes |
| 92 | C.P.V.C. PIPESProviding and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.Internal work - Exposed on wall.25 mm nominal outer dia Pipes |
| 93 | C.P.V.C. PIPESProviding and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.Internal work - Exposed on wall.40 mm nominal outer dia Pipes |
| 94 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.Concealed work, including cutting chases and making good the walls etc.15 mm nominal dia Pipes |
| 95 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.Concealed work, including cutting chases and making good the walls etc.20 mm nominal dia Pipes |
| 96 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.Concealed work, including cutting chases and making good the walls etc.25 mm nominal dia Pipes |
| 97 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :25 mm nominal bore |
| 98 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :20 mm nominal bore |
| 99 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :32 mm nominal bore |
| 100 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :40 mm nominal bore |
| 101 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :15 mm nominal bore each |
| 102 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :20 mm nominal bore |
| 103 | Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet :100 mm diameter |
| 104 | Providing and fixing PTMT grating of approved quality and colour.Circular type125 mm nominal dia with 25 mm waste hole |
| 105 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 106 | C.P. BRASS FITTINGSProviding and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.15 mm nominal bore |
| 107 | Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.15 mm nominal bore |
| 108 | Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour.15 mm nominal bore with 45 cm length |
| 109 | Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70kg as per standard design:150x100 mm size P typeWith Sewer bricks conforming to IS : 4885 |
| 110 | Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone- III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design :Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) :With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 111 | Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality.L D- 2.5Rectangular shape 600x450 mm internal dimensions |
| 112 | Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design.With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 113 | Excavating, supplying, stacking and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in foundation trenches, plinth, sides of foundation etc. complete for all lift. |
| 114 | Surface dressing of the ground including removing vegetation and in equalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m. |
| 115 | Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared. |
| 116 | Clearing grass and removal of the rubbish up to a distance of 50 m outside the periphery of the area cleared. |
| 117 | Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge. |
| 118 | Extra for cutting reinforcement bars manually/ by mechanical means in R.C.C. or R.B. work (Payment shall be made on the cross sectional area of R.C.C. or R.B. work) as per direction of Engineer-in-charge. |
| 119 | Laying, spreading and compacting stone aggregate of specified sizes to WBM specifications in uniform thickness, hand picking, rolling with 3 wheeled road/vibratory roller 8-10 tonne capacity in stages to proper grade and camber, applying and brooming requisite type of screening / binding material to fill up interstices of coarse aggregate, watering and compacting to the required density . |
| 120 | Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50 mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge.60 mm thick cement concrete paver block of M-35 grade with approved colour, design & pattern. |
| 121 | Trenching in ordinary soil up to a depth of 60 cm including removal and stacking of serviceable materials and then disposing of surplus soil, by spreading and neatly levelling within a lead of 50 m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or / and manure before and after flooding trench with water (excluding cost of imported earth, sludge or manure). |
| 122 | Supplying and stacking of good earth at site including royalty and carriage upto 5 km lead complete (earth measured in stacks will be reduced by 20% for payment). |
| 123 | Supplying and stacking sludge at site including royalty and carriage upto 5 km lead complete (sludge measured in stacks will be reduced by 8% for payment). |
| 124 | Supplying and stacking of well decayed cattle manure at site including royalty and carriage upto 5 k.m.lead complete (Cattle manure measured in stacks will reduced by 8% for Payment). |
| 125 | Spreading of sludge, dump manure and/or good earth in required thickness as per direction of officer-in-charge (cost of sludge, dump manure and/ or good earth to be paid separately). |
| 126 | Providing and wartering of irrigation water through water tanker of Horticulture features i.e. lawn, tree, shrubs, hedge/edge, ground cover etc. at the site of work. Water tanker having 5000 lit. capacity with one labour for watering i/c cost of water, filling of tanker, wartering at site with all leads and lifts as per direction of officer-in-charge. |
| 127 | Plantation of Trees, Shrubs and Hedge at site i/c watering and removal of unserveiceable material’s as per direction of officer in charge (excluding cast of plant & water)Trees Plant |
| 128 | Plantation of Trees, Shrubs and Hedge at site i/c watering and removal of unserveiceable material’s as per direction of officer in charge (excluding cast of plant & water).Hedge Plant /Ground cover |
| 129 | Providing and stacking of Duranta Golden, having ht.15 to 20 cm bushty shape with fresh and healthy leaves in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge.. |
| 130 | Providing and stacking of Iresine herbstii, of height 20-25 cm. full of branches well developed in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge. |
| 131 | Providing and stacking of Delonix regia (Gulmohar) of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.v |
| 132 | Providing and stacking of Ficus benjamina (green) of height 150-165 cm., bushy with healthy branches and lush green foliage in big size HDPE bags as per direction of the officer-in-charge. |
| 133 | Providing and stacking of Bottle palm of ht. 210-240 cm bottom girth 30-35 cm well developed in big HDPE bags. |
| 134 | Stone work (machine cut edges) for wall lining etc. (veneer work) upto 10 metre height, backing filled with a grout of average 12 mm thick cement mortar 1:3 (1 cement : 3 coarse sand) including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade : (To be secured to the backing and the sides by means of cramps and pins which shall be paid for separately) :Red sand stone - exposed face fine dressed with rough backing. 30mm thick |
| 135 | Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-in-charge, upto 90 metre depth below ground level.All types of soil400 mm dia |
| 136 | Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-in-charge, upto 90 metre depth below ground level.Rocky strata including Boulders400 mm dia |
| 137 | Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, beyond 90 metre depth below ground level. Rocky strata including Boulders400 mm dia |
| 138 | Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge.200 mm nominal size dia |
| 139 | Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge. |
| 140 | Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge. |
| 141 | Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer -incharge. |
| 142 | Development of tube well in accordance with IS : 2800 (part I) and IS:11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by \\"V\\" notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge. |
| 143 | Providing and fixing M.S. clamp of required dia to the top of casing/housing pipe of tubewell as per IS: 2800 (part I),including necessary bolts & nuts of required size complete.200 mm clamp |
| 144 | Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I). 200 mm dia |
| 145 | Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc.External work65 mm dia nominal bore |
| 146 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :65 mm nominal bore |
| 147 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.Group C |
| 148 | Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required. |
| 149 | Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire |
| 150 | Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.2 X 4 sq. mm + 1 X 4 sq. mm earth wire |
| 151 | Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.2 X 6 sq. mm + 1 X 6 sq. mm earth wire |
| 152 | Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.4 X 10 sq. mm + 2 X 6 sq. mm earth wire |
| 153 | Supplying and fixing 3 pin, 5 amp ceiling rose on the existing junction box/ wooden block including connection etc as required. |
| 154 | Supplying and fixing brass batten/ angle holder including connection etc. as required. |
| 155 | Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc as required.3 Module (100mmX75mm) |
| 156 | Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc as required.4 Module (125mmX75mm) |
| 157 | Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.3 Module |
| 158 | Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.4 Module |
| 159 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.5/6 amps switch |
| 160 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.3 pin 5/6 amp socket outlet |
| 161 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.15/16 amp switch |
| 162 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.6 pin 15/16 amp socket outlet |
| 163 | Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)2 + 8 way, Double door |
| 164 | Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator).4 way (4 + 12), Double door |
| 165 | Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 volts, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 amps tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCB's (but without MCB's and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.)8 way (4 + 24), Double door |
| 166 | Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, \\"C\\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single pole |
| 167 | Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, \\"C\\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Double pole |
| 168 | Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps |
| 169 | Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required. |
| 170 | Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps |
| 171 | Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.63 amps |
| 172 | Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required. |
| 173 | Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm). |
| 174 | Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required. |
| 175 | Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable etc. as required. |
| 176 | Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required.Upto 450 mm sweep |
| 177 | Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.Upto 35 sq. mm |
| 178 | Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.Above 35 sq. mm and upto 95 sq. mm |
| 179 | Erection of steel tubular or rail pole strut in cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size ) foundation including excavation and refilling and secured with holding clamps, bolts, nuts, etc. as required. |
| 180 | Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.Substation Earthing &Transformer Panel |
| 181 | Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required.Substation Earthing &Transformer Panel |
| 182 | Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm).Transformer Neutral Earthing |
| 183 | Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. (but without charcoal/ coke and salt ) as required. |
| 184 | Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm). |
| 185 | Construction of RCC Foundation for DG Set |
| 186 | Supplying, installation, testing & commissioning of sector panel suitable for 4 zones, complete with visual indications for short circuit fault, open circuit fault, fire condition and all other standard facilities as per IS:2189 with mimic diagram for all area/zone covered, complete with all connections and interconnections as required. |
| 187 | Supplying, installation, testing & commissioning of manual call box of ABS type in surface/recess with stainless steel chain & hammer assembly complete with glass and push button etc. as required. |
| 188 | Supplying, installation, testing & commissioning fire alarm sounder with facility to make announcement, mounted in A.B.S. box with hinged cover plate and suitable for operation with amplifier including line matching transformer etc. complete as required. |
| 189 | Supplying and drawing of fire retardant PVC insulated copper conductor speaker/fire alarm cable, single pair, 2-core, 1.5 sq.mm in the existing surface/recessed steel conduit including connections and interconnections etc. as required. |
| 190 | Providing and fixing solid full height partition 3000 mm high made with wooden framework of seasoned hollock wood battens 50 × 50 mm size placed at 600 mm c/c both ways, finished with 18 mm thick BWR grade plywood on both sides and 1.0 mm thick decorative laminate on both faces including adhesive, nails, screws etc. complete, including 75 × 18 mm teak wood bead fixed horizontally at 1200 mm above finished floor level as per approved design and direction of Engineer-in-Charge. |
| 191 | Providing and fixing solid full height wall panelling 3000 mm high made with wooden framework of seasoned hollock wood battens 50 × 50 mm size placed at 600 mm c/c both ways, finished with 18 mm thick BWR grade plywood on exposed sides and 1.0 mm thick decorative laminate on over ply faces including adhesive, nails, screws etc. complete, including 75 × 18 mm teak wood bead fixed horizontally at 1200 mm above finished floor level as per approved design and direction of Engineer-in-Charge. |
| 192 | Providing and fixing partly glazed partition 3000 mm high made with seasoned hollock wood framework including grooves and 75 x 18 mm wooden bead at 1200 mm height, finished with 18 mm thick BWR grade plywood and 1.0 mm thick decorative laminate on both exposed faces complete with approved adhesive, nails, screws and all necessary fittings. The partition shall include 5 mm thick float glass with approved etching from 1200 mm to 2100 mm from finished floor level and solid laminated portion above and below complete as per approved drawing and direction of Engineer-in-Charge. |
| 193 | Providing and fixing partly glazed partition of height 1500 mm made with seasoned hollock wood framework including grooves and 75 x 18 mm wooden bead running horizontally at 1200 mm height, finished with 18 mm thick BWR grade plywood and 1.0 mm thick decorative laminate on both exposed faces complete with approved adhesive, nails, screws and all necessary fittings. The partition shall include 5 mm thick float glass with approved etching from 1200 mm level up to 1500 mm from finished floor level complete as per approved drawing and direction of Engineer-in-Charge. |
| 194 | Supplying 1200 mm sweep ceiling fan Orient /Usha/Cromton/Bajaj make. |
| 195 | Supplying of 300 mm Heavy Duty Exhaust Fan ( 900 RPM) Orient make. |
| 196 | Supplying,Installation, testing and commissioning of surface mounted LED batten (20W) fitting 1200mm length having Lumen efficacy ≥ 120lm/watt, System Lumen output ≥ 2000 lm, Metal housing , CRI ≥ 80, Power factor ≥ 0.9, THD ≤ 10% having suitable diffuser and CCT in between 4000K to 6500 K (i/c both Limits) complete with all accessories etc. directly on ceiling/wall including connection with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required. (Philips/ Bajaj/ WIPRO/ JAQUAR or equivalent make). |
| 197 | Supplying,Installation, testing and commissioning of recess mounted LED downlighter having Lumen efficacy ≥ 100lm/watt, System Lumen output ≥ 600 lm, Metal housing , CRI ≥ 80, Power factor ≥ 0.9, THD ≤ 10% having suitable diffuser and CCT in between 4000K to 6500 K (i/c both Limits) complete with all accessories etc. directly on ceiling/wall including connection with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required. Philips Green Perform Sleek Model DN296B LED20S-6500 PSU WH Or equivalent (Equivalent will be selected by the deptt considering the mother items rate) (equivalent Bajaj / WIPRO/ JAQUAR make). |
| 198 | Supplying fitting & fixing of LED Bulb non-dimmable in the existing batten / angle holder as required and as directed by the department ( Syska or eqvt. make). LED SRL Bulb (Maxglow) B-22 Base (6500K) -15W. |
| 199 | \\"Supplying with installation testing and commissioning of Hi -wall split (Cordless remote) air conditioner of the following capacity complete with indoor and outdoor unit, copper pipe and electrical connection up to 5 m between the room unit and out door unit as directed by the department. Warranty: Company will have to provide warranty on the entire product for twelve months from the date of commissioning. Additional warranty on Rotary & Scroll Compressor will be four and two years respectively. Service: Three free services will have to be provided by the company apart from the breakdown calls, if any. Approved make Carrier/ Hitachi/Diakin /Voltas/ Mitshubishi/Blustar or equivallant make. 3 star rating--0.8-1.2TR inverter split, |
| 200 | \\"Supplying with installation testing and commissioning of Hi -wall split (Cordless remote) air conditioner of the following capacity complete with indoor and outdoor unit, copper pipe and electrical connection up to 5 m between the room unit and out door unit as directed by the department. Warranty: Company will have to provide warranty on the entire product for twelve months from the date of commissioning. Additional warranty on Rotary & Scroll Compressor will be four and two years respectively. Service: Three free services will have to be provided by the company apart from the breakdown calls, if any. Approved make Carrier/ Hitachi/Diakin /Voltas/ Mitshubishi/Blustar or equivallant make. 3 star rating--1.8-2.2TR inverter split, |
| 201 | Supplying with fitting and fixing Voltage stabilizer of the following specification complete including making necessary connection as approved, specified and directed by the deptt. 5.0 KVA Automatic Input 90-280 V Out put 200-240 V, (Vee-Dee/Luminous or equivallant make) |
| 202 | Supplying with fitting and fixing of Single Phase Modular Motor Starter switch of the following specification complete including making necessary connection as specified and directed by the deptt. Overload Relay Range 16 - 25 Amps in 3 Module |
| 203 | Supplying including installation,testing and commissioning of Extra Refrigerant pipe for Split type Air Conditioner Machine as specified and directed by the department |
| 204 | Supply of following sizes XLPE insulated and PVC sheathed aluminium conductor armoured power cable of 1.1 KV grade conforming to IS 7098 (Part - I) / 1988 with amendment up to date etc as required. (RR Kabel/Nicco/ Havells/ RPG/CCI/Polycab/Gloster/ Finolex make or equivalent) . 2 C x 16 Sq.mm |
| 205 | \\"Supply of following sizes XLPE insulated and PVC sheathed aluminium conductor armoured power cable of 1.1 KV grade conforming to IS 7098 (Part - I) / 1988 with amendment up to date etc as required. (RR Kabel/Nicco/ Havells/ RPG/CCI/Polycab/Gloster/ Finolex make or equivalent) . 3&1/2 x 50 Sq.mm |
| 206 | \\"Supplying with fitting and fixing panel mounting open execution 25KA 415V 50Hz 3P MCCB (Ics=Icu, adustable Ir setting 0.5-1, neutral adjustable with earth fault protection and with rotary handle) (without enclosure) of the following capacity complete with making necessary connection as specified and directed by the deptt.1. 25 KA 415V 50 Hz 3P MCCB , 125A (Schneider, legrand, Siemens, L&T, Hager or equivallant make)\\" |
| 207 | \\"Supplying with fitting and fixing panel mounting open execution 25KA 415V 50Hz 3P MCB, neutral adjustable with earth fault protection and with rotary handle) (without enclosure) of the following capacity complete with making necessary connection as specified and directed by the deptt.1. 25 KA 415V 50 Hz 3P MCB , 63A (Schneider, legrand, Siemens, L&T, Hager or equivallant make)\\" |
| 208 | \\"Supplying with fitting and fixing panel mounting open execution 25KA 415V 50Hz DP MCB, neutral adjustable with earth fault protection and with rotary handle) (without enclosure) of the following capacity complete with making necessary connection as specified and directed by the deptt.1. 25 KA 415V 50 Hz DP MCB , 40A (Schneider, legrand, Siemens, L&T, Hager or equivallant make)\\" |
| 209 | Supplying, installation, testing and commissioning of the 63KVA 11/0.4KV aluminium wound out door type oil filled Level-2 Distribution Transformer complete including all accessories like Earthing terminal, Liftung Lugs, Drain Valve, Oil filling Hole with plug, Silicagel Breather, First filling of Oil as per IS355, Arcing Horn, Radiator, Air Release Plug, Conservator Tank etc along with cost of load security, Meter Security and making necessary arrangement of obtaining NOC for charging approval of the sub-station from the competent authority as directed and specified by the department. Transformer should be as per CEA guidelines as ammended up to date . |
| 210 | Supplying hot dip Galvanized Steel tubular pole manufacturing out from electrically welded in 3 (three section having a base plate including providing all required building materials as directed and specified by the deptt. (BANSAL/SRP / Valmont / PARUTHI ENGR make) 410 SP 66 Length of pole = 12.00 metre., Length of sections, Bottom = 5.80 M, Middle = 3.10 M, Top = 3.10 M, Out side dia. & Thickness Bottom = 219.10 x 5.60 mm, Middle =193.7 x 4.85 mm, Top =165.10 x 4.50 mm |
| 211 | Supplying and fixing of 11KV GOAB Switch 150Amp with all accessories complete as required and as directed by the department. |
| 212 | Supplying and fixing of 11 KV 150 A D.O. fuse set complete as required and as directed by the department. |
| 213 | Supplying and fixing of 11 KV 5 KA Lighting arrestor (Poly) set complete as required and as directed by the department. |
| 214 | Supplying with fitting and fixing of galvanised channel of 100 mm x 50 mm x 6mm, 2200 mm long complete with clamps ,blots, nuts etc. as required and as directed by the department. |
| 215 | Supplying with fitting and fixing of Pole clamp of G.I. Flat (50x6)mm , as required and as directed by the department. |
| 216 | Supplying with fitting and fixing of G.I. LT Angle Crosarm( 40x40x6x500 ) mm , as required and as directed by the department. |
| 217 | Supplying with fitting and fixing of G.I. Angle (50x50x6)mm , as required and as directed by the department. |
| 218 | Supplying with fitting and fixing of G.I.Nuts & Bolts with washer , as required and as directed by the department. |
| 219 | Supplying with fitting and fixing of Microprocessor based with inbuilt earth fault protection module 4 pole MCCB 200A ICS= 100%, ICU 35KA(Minimum) , as required and as directed by the department. |
| 220 | Supplying of following sizes XLPE insulated and PVC sheathed aluminium conductor armoured power cable of 1.1 KV grade conforming to IS 7098 (Part - I) / 1988 with amendment up to date etc as required. (RR Kabel/Nicco/ Havells/ RPG/CCI/Polycab/Gloster/ Finolex make or equivalent).a) 3&1/2 x 50 Sq.mm Tr. Panel to Vertical TPDB( Main Building) |
| 221 | Supplying with fitting and fixing of Aluminium Lugs 50 sq mm , as required and as directed by the department. |
| 222 | Supplying with fitting and fixing of C.I. Earth Pipe 1.8m Inner dia 100mm, outer dia 110mm with perforated holes of 15mm dia at 30 cm interval along length of the pipe |
| 223 | Supplying with fitting and fixing of 1.1 KV (LT) Grade Armoured 1CX95 sq mm Aluminium , as required and as directed by the department. |
| 224 | Supplying with fitting and fixing of Aluminium Lugs 95 sq mm , as required and as directed by the department. |
| 225 | Supplying including installation, commissioning of vermin and dust proof totally enclosed cubical indoor type floor/wall mounting compartmentalize panel board of size 1.1M(B)X1.0M(H) X 0.40M(D) made of 16 SWG (1.66 mm) thick C.R. sheet and 35mm X 35mm X 5mm size angle having 4 nos legs at the bottom complete painting with 2 coats of Red Oxide metal primer and 2 coats of Enamel paint. The panel board is to be errected in 1 : 3 : 6 PCC foundation including brick soling / grouting etc. complete neatly wiring done with provision for one no 400A 4pole 415V MCCB or Switch Fuse Unit as incomer and provision for 2nos DP orTPN out going as as specified and directed by the deptt. confirming to IP 43 protection comprising of the following electrical items:1. i) 40mm X 5mm 4 strip copper Bus-Bar 1.0M length each ii) 20mm X 3mm 4 strip copper Bus-Bar 0.5M each 2 sets3. Poilt Lamp with integral ckt LED 110- 230 V (Red,Yellow,& Blue) - 3 nos4. Voltmeter & Ammeter Selector Switch - 2 nos5. 2 A Slide fuse unit - 3nos(Incoming & Outgoing Switch Gear of reqd. rating along with Meters will be measured and paid separately)Transformer Panel |
| 226 | Supplying with fitting and fixing of LT Trivector energy meter with Metering Cabinet, as required and as directed by the department. |
| 227 | Construction of 11KV Over Head High Tention Line ( to be paid to APDCL as a Deposit works) |
| 228 | Load security to be paid to APDCL (APDCL Norms). |
| 229 | Supplying fitting & fixing Single phase Submersible motor pump set suitable for 100 mm bore well and above 2 HP as directed & specified by the Department. (Texmo / Crompton Greaves/ Aquatic/ CRI/ V-Guard or equivallant make) |
| 230 | \\"Supplying fitting & fixing of Submersible motor pump set control panel as directed & specified by the Department. Type-FS 2HP DOL((Make- Havells,L&T,CRI or equivallant ) |
| 231 | \\"Supplying fitting & fixing Three core cable with bare bounched copper conductor insulated & sheathed with pvc for Submersible pump motor as directed and specified by the department, Finolex/RRKabel/Havells or equivallant make. 3 core 6.00 sq mm |
| 232 | Supplying fitting & fixing of Wair Rope 10 mm size for keeping Submersible pump motor as directed and specified by the department. |
| 233 | \\"Supplying including installation, testing and commissioning of Air/Water Cooled Diesel Generator set coupled to suitable alternator of 220/415 V, AC, 1/3-Phase 0.8 p.f. mounted on a 1) M.S. Fabricated base frame.,2) M.S. fuel tank of required capacity.,3) Residual Silencer.,4) AMF Control Panel.5) Suitable batteries with lead.,6) First fill of lube oil.,7) Acoustic Enclosure complete with all accessories as specified and directed by the department conforming to IS comprising the Technical Specification.. as per manufacturer.(Kirloskar green/bliss, Leyland, Volvo Penta, Perkinson, Mahindra, Greaves, Escort engine and Kirloskar, Stamford, Greaves, Leroy somer alternator).25 KVA DG Set with AMF Panel |
| 234 | \\"Supplying with fitting and fixing Four Pole 415V Front handle operated On Load Change over switch (IP-20 protection) in powder painted sheet steel enclosure fitted on angle iron frame of the follwing capacity complete with making necessary connection as specified and directed by the deptt. (Standard/L&T/ Havells/ C&S/ HPL, make) |
| 235 | Supply and installation of ROLLER Blind of size 6' x 6' |
| 236 | Supply and installation of ROLLER Blind of size 4' x 4' |
| 237 | Supply and installation of Portable fire extinguisher of 2Kg. |
| 238 | Supply, Installation, Testing and Commissioning of 2MP IP Dome Camera.(Make:- CP Plus/ Honeywell/ Prama) |
| 239 | Supply, Installation, Testing and Commissioning of 2MP IP Bullet Camera.(Make:- CP Plus/ Honeywell/ Prama) |
| 240 | Supply, Installation, Testing and Commissioning of 16Ch Network Video Recorder (NVR).(Make:- CP Plus/ Honeywell/ Prama) |
| 241 | Supply, Installation, Testing and Commissioning of 4TB Harddrive for Storage.(Make:- Seagate/ WD/ Toshiba) |
| 242 | Supply, Installation, Testing and Commissioning of 32\\" Display.(Make:- LG/ Panasonic) |
| 243 | Supply, Installation, Testing and Commissioning of 8 Port PoE Switch.(Make:- DLink/ Netgear) |
| 244 | Supply and Laying of Cat6 UTP Cables including RJ45 Connectors.(Make:- DLink/ Finolex) |
| 245 | Supply and Installation of 6U Wall Mount rack.(Make:- Dlink/ Valrack/ Nettrack) |
| 246 | Supply and Laying of 25MM PVC Conduits.(Make:- AKG/ Berlia) |
| 247 | Supply, Installation, Testing and Commissioning of 65\\" 4K UHD Display.SCREEN SIZE:- 165 cm, PANEL TECHNOLOGY:- IPS PANEL, D-LED, ASPECT RATIO:- 16:9, RESOLUTION:- (3840*2160)UHD, BRIGHTNESS:- 400 Nits, VIEWING ANGLE:- 178° (H/V), RESPONSE TIME:- 8ms, CONTRAST RATIO:- 1200:1, OPERATION HOURS:- 24 / 7(Make:- LG/ Christie/ Barco) |
| 248 | Supply, Installation, Testing and Commissioning of 5000 Lumens XGA Laser Projector.(Make:- Sony/ Christie/ Panasonic) |
| 249 | Supply, Installation, Testing and Commissioning of 8 Feet X 6 Feet Projection Screen.(Make:- Liberty/ Milan/ Suvira) |
| 250 | Supply, Installation, Testing and Commissioning of Projector Ceiling Mount Kit (Make:- Liberty/ Milan/ Suvira) |
| 251 | Supply, Installation, Testing and Commissioning of Wireless Lapel Microphone. (Make:- Audio technica/ AKG/ Sennheiser). |
| 252 | Supply, Installation, Testing and Commissioning of Wireless Handheld Microphone. (Make:- Audio technica/ AKG/ Sennheiser). |
| 253 | Supply, Installation, Testing and Commissioning of 120W Mixer Amplifier. (Make:- Bosch/ Behringer/ Labgruppen). |
| 254 | Supplying installation, testing, programming and commissioning of Video equipment HDMI HDBaseT Extender (4K@40m) (HDBaseT Class B) (Make:-Purelink/ Atlona/ aTEN). |
| 255 | Supply, Installation, Testing and Commissioning of 4x1 4K 18Gbps HDMI Switcher. (Make:-Purelink/ Atlona/ Aten) |
| 256 | Supply, Installation, Testing and Commissioning of 4K HDMI 2.0a Splitter. (Make:-Purelink/ Atlona/ Aten) |
| 257 | Supply and Laying of Audio Cables like Speaker Cables, Audio Signal Cables, Connectors like XLR, RCA, 3.5MM EP etc.(Make:- Gotham/ Belden/ Amphenol/ Neutrik) |
| 258 | Supply anc Installation of 17U Floor Mounted Equipment Rack.(Make:- Dlink/ Nettrack/ Valrack) |
| 259 | MODEL: STATESMANTABLE SIZE: 3000 X 2000 X 760HT MMSpecifications:E1 grade MDF with natural veneer and painting finish. Fixed side return by LEFT HAND as picture.Table top 70mm thick and covered by PU leather, with 1pc multi-functional wirecase.Make: Featherlite |
| 260 | MODEL: SENATOR HBSpecifications:FP Senator High Back * Aluminium Base * Multilock Mechanism * Aluminium Fixed Arms * Leatherette upholstered seat & back.Make: Featherlite |
| 261 | MODEL: BRAVO VASpecifications:Bravo Low Back Visitor * Fixed Arms * Powdercoated Sledge Base * Leatherette Seat & Back.Make: Featherlite |
| 262 | MODEL: HT- 531MAIN TABLE SIZE: 1600 X 750 X 780HT MM EXTENSION SIZE: 905 X 440 X 650HT MMSpecifications:Table top: 54mm thick Pre-laminate MDF board finished with 2mm PVC Edge Banding.Under Structure: Supported on MS Powder Coated Brackets and cross beams.25mm thick pre-laminated MDF gable end or Main table desk is Supported on Side storage unit and other side 3 drawer Pdestal.Pedestal Configuaration and usign Laminate board and Thickes.Modesty panel: 18mm Thick pre-laminated MDF Modesty panel of 450HT.Wire Management: 1 No. of 450mm Aluminium Flip Up and provision to mount swicthes and sockets on metal cable Dump and vertebra considered for wire uptake from floor to cable dump.Side Storage: (single door and 3 drawers) The structure is made out of 18mm thick pre-laminated MDF boards.Make: Featherlite |
| 263 | MODEL: AMAZE HBSpecifications:High Mesh Back ChairFabric Upholestered Csuhioned Seat Adjustable Lumbar Support Adjustable Armrest & Headrest Self-Calibrating Mechanism Multi-Lock Mechanism Nylon BaseMake: Featherlite |
| 264 | MODEL: CONTACT VASpecifications:Mesh Back Visitor ChairFabric Upholestered Csuhioned Seat Fixed Armrest MS Powdercoated Sledge Base.Make: Featherlite |
| 265 | MODEL: FST TABLEMAIN TABLE SIZE: 1500 X 750 X 750HT MM SIDE STORAGE: 900 X 450 X 750HT MMSpecifications:Table top: Made of 25mm thick prelaminated particle board of approved shade. All the edges of cabin table surface shall be provided with machine pressed 2mm thick imported PVC lipping glued with hotmelt Eva glue free from any VOC.Under Structure: 25mm thick PLT gable end.Modesty Panel: 18mm thick 450mm ht plt modesty panel is considered.Wich is machine pressed 2mm thick imported PVC lipping glued with hotmelt Eva glue free from any VOC.Wire Management: 2 nos. of 65mm dia gromet hole for wire access.Make: Featherlite |
| 266 | MODEL: COMET HBSpecifications:High Mesh Back ChairFabric Upholestered Csuhioned Seat Fixed Headrest Adjustable Lumbar Support Adjustable Armrest Single-Lock Mechanism Nylon BaseMake: Featherlite |
| 267 | MODEL: PERFORM WORKSTATION SIZE: 1500 X 600 X 750HT MMSpecifications:Table top: Made of 25mm thick prelaminated particle board of approved shade. All the edges of cabin table surface shall be provided with machine pressed 2mm thick imported PVC lipping glued with hotmelt Eva glue free from any VOC.Under Structure Support: MS Powdercoated Perform legs.Wire Management: The Raceways are provided below the work surface for carrying wires from one end to other end of the cluster, Size offered is 250mm Ht, Thickness 70mm. 65mm dia grommet hole is provided for wire access.MOBILE PEDESTAL : 2D 1FMake: Featherlite |
| 268 | MODEL: PERFORM WORKSTATION L-SHAPED SIZE: 1500/1500 X 600/600 X 750HT MMSpecifications:Table top: Made of 25mm thick prelaminated particle board of approved shade. All the edges of cabin table surface shall be provided with machine pressed 2mm thick imported PVC lipping glued with hotmelt Eva glue free from any VOC.Under Structure Support: MS Powdercoated Perform legs.Wire Management: The Raceways are provided below the work surface for carrying wires from one end to other end of the cluster, Size offered is 250mm Ht, Thickness 70mm. 65mm dia grommet hole is provided for wire access.MOBILE PEDESTAL : 2D 1FMake: Featherlite |
| 269 | MODEL: PERFORM MEETING TABLE SIZE: 4200 X 1200 X 750HT MMSpecifications:Table top: Made of 25mm thick prelaminated particle board of approved shade. All the edges of cabin table surface shall be provided with machine pressed 2mm thick imported PVC lipping glued with hotmelt Eva glue free from any VOC.Under Structure Support: MS Powdercoated Perform legs.Wire Management: 450mm Alu. Puffed anodised flipup with cable dump with provision for switch and sockets, for easy power acces.Make: Featherlite |
| 270 | MODEL: COMET MBSpecifications:Medium Mesh Back ChairFabric Upholestered Csuhioned Seat Adjustable Armrest Single-Lock Mechanism Nylon Base.Make: Featherlite |
| 271 | MODEL: BARISTERSpecifications:MADE OFF : NEEM WOOD FRAME, SUPPORTED BY HIGH QUALITY OF WEBBING BELT, 40/32/40 DENSITY FOAM USED FOR UPHOLSTERY, 2” FOAM ARE USED ON TOP OF SEAT, FOR BETTER SUPPORT AND EXTRA COMFORT, ALL HARDWARE – USED FROM KANGAROO COMPANY (STAPLE PINS/ SOLUTIONS/ NAILS / SCREW-NUTS ETC), FABRIC CAN BE USED OF SF SEREIS FABRIC OR RESPONSE STYLO LEATHERRETE SHADE CARD . (LEGS ARE POWDER COATED GOLD – METAL LEGS)Make: Featherlite, 3 SEATER |
| 272 | MODEL: BARISTERSpecifications:MADE OFF : NEEM WOOD FRAME, SUPPORTED BY HIGH QUALITY OF WEBBING BELT, 40/32/40 DENSITY FOAM USED FOR UPHOLSTERY, 2” FOAM ARE USED ON TOP OF SEAT, FOR BETTER SUPPORT AND EXTRA COMFORT, ALL HARDWARE – USED FROM KANGAROO COMPANY (STAPLE PINS/ SOLUTIONS/ NAILS / SCREW-NUTS ETC), FABRIC CAN BE USED OF SF SEREIS FABRIC OR RESPONSE STYLO LEATHERRETE SHADE CARD . (LEGS ARE POWDER COATED GOLD – METAL LEGS)Make: Featherlite, 1 SEATER |
| 273 | MODEL: SENATOR HBSpecifications:FP Senator High Back * Aluminium Base * Multilock Mechanism * Aluminium Fixed Arms * Leatherette upholstered seat & back.Make: Featherlite Size: 1050 w x 600 D x 450 Ht mm |
| 274 | MODEL: SENATOR HBSpecifications:FP Senator High Back * Aluminium Base * Multilock Mechanism * Aluminium Fixed Arms * Leatherette upholstered seat & back.Make: Featherlite Size: 600 w x 600 D x 450 Ht mm |
| 275 | MODEL: STORAGESSpecifications:Top & Sides: 18mm Thk pre laminated particle board Back: 9mm Thk pre laminated particle board Shutters: 18mm Thk pre laminated particle board.Edge: All exposed area with 2mm thick PVC edge lipping.Handle: Finger groove handle.Make: FeatherliteSIZE: 900W X 450D X 1200HT MM |
| 276 | MODEL: STORAGESSpecifications:Top & Sides: 18mm Thk pre laminated particle board Back: 9mm Thk pre laminated particle board Shutters: 18mm Thk pre laminated particle board.Edge: All exposed area with 2mm thick PVC edge lipping.Handle: Finger groove handle.Make: FeatherliteSIZE: 750W X 450D X 1200HT MM |
| 277 | MODEL: Alpha SINGLE BED[11:29 am, 13/05/2025] Kcc Pranjal: The cot design is modular & minimalistic, quick & easy to assemble, stable & sturdy to take adequate weight.Verticals are from Sq.40x40x1.60mm thk (16g) tubes and horizontal beams are Rectangular tubular profiles of 60x40 confirming to IS 4923:2017. All 04 vertical sections/legs are connected to to form the under-structure, confirming to IS 4923:2017 grade.Beam to beam are connected by cross beams of Sq.20mm ERW tube confirming to IS 4923:2017, which supports the mattress platform. Mattress platform is of 12mm thk plywood sheet. All metal parts comes with powder coating finish 60-80 microns thk.The legs are fitted with PPGF moulded leg bushes & levellers to adjust heights upto 20mm based on ground undulations.[11:30 am, 13/05/2025] Kcc Pranjal: 2060L X 900D X 400-750HMake: Featherlite |
| 278 | MODEL: FST TABLEMODEL: FSTSIZE: 2100L X 750D X 750HTTable top: Made of 25mm thick prelaminated particle board of approved shade confirming to E1 norms. All the edges of cabin table surface shall be provided with machine pressed 2mm thick imported PVC lipping glued with hotmelt Eva glue free from any VOC. nos each.Understructure: 25mm thick PLB gable ends and 18mm thick 450ht PLT.modesty panels with necessary fixtures. Modesty Panel: Made up of 18mm thick PLB.Wire Management: 350mm Anodised flip up Made of Aluminum in anodised finish, which has soft closure and three way wire acess & PVC cable tray.For entry of cables from the floor into the cable tray, Wire entry cover are provided for the access of wire from the floor.Make: Featherlite |
| 279 | MODEL: COMET MBSpecifications:Medium Mesh Back ChairFabric Upholestered Csuhioned Seat Adjustable Armrest Single-Lock Mechanism Nylon Base.Make: Featherlite |
| 280 | MODEL: GENIUS VA WDSpecification:Genius Stackable Chair Powdercoated Legs With writing desk.Make: Featherlite Please Enable Macros to View BoQ information |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
| 5 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
