|
| 1 | Laying and Jointing PVC Pipe. Heading |
| 2 | Dismantling of area 3 sq. metres and below doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead |
| 3 | Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable surplus material and stacking of serviceable material with in 50 meters lead as directed by Engineer-in-charge. |
| 4 | Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks) |
| 5 | Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on interlocking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main \\"T\\" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross \\"T\\" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main \\"T\\" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross \\"T\\" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main \\"T\\" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanized butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge.8 mm thick fully perforated calcium silicate board made with Calcareous & Siliceous materials reinforced with cellulose fiber manufactured through autoclaving process to give stable crystalline structure with minimum compressive strength 225 kg/ sq. cm, bending strength 100 kg/sq. cm , of size 595x595 mm, having perforation of dia. 10 mm with minimum perforated area 18 % with non woven tissue on the back side, having an NRC ( Noise Reduction Coefficient) of 0.85, with 50 mm thick rockwool of 48 kg /cum backing. |
| 6 | Providing ,making & fixing wall panneling as per drawing from seasoned wood of MIRINDI frame of 2\\"X2\\" size placed horizontally and vertically both way @ 2 ' c/c. the frame work fitted in floor with the help of nails ,screw then frame work to be covered with 12 mm thick plywood from the help of fevicol,nails and screw. then making grooves with 6mm MDF Ply with the help of fevicol,nails and screw. The final surface to be finished with 1mm thick laminate and grooves to polished as per design.. as per requirement and direction of Engineer I/C including cost of all material, labour, T & P etc required for proper completion of work. |
| 7 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross band and face veneers on both faces of shutters.35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws . |
| 8 | Providing & fixing of flush door Laminated both side complete with all fittings,Round mortis lock,door closer etc all complete all complete as per drawing, specification and direction as approved by the Architect/ Engineer -in-Charge |
| 9 | Providing and fixing of 8 MM Thick wooden flooring, classification of use 32/23 with a surface abrasion resistance of class AC5 (average 6500 cycles), wear layer on top of a High Density Fiber substrate core (density ~890-900 Kgs/M3) of plank size 1216 mm X 197 mm having Lock & Fold locking arrangement and edge type 0.5 Small V -Groove. Surface finish will be Real wood Touch Surface . Underlayment for laminate flooring made of natural color foam (Including of dismantaling existing wooden flooring and disposal of material). all complete as per drawing, specification and direction as approved by the Architect/ Engineer -in-Charge. The work include cost of all labour,material T&P required for proper completion of work. Model -Robust Make- Lamiwood or Equivalent. |
| 10 | Providing and fixing of 8 MM Thick wooden flooring Skirting (80mm) . The work include cost of all labour,material T&P required for proper completion of work Make- Lamiwood or Equivalent. |
| 11 | Providing & Fixing of dual layer Roller Zebra blinds kazage dew /Johnson make of approved shade as per drawing & specification as approved by the Architect/ Engineer -in-Charge. The work includes cost of all labour, material T&P for proper completion of work |
| 12 | Providing and fixing factory made uPVC glazed/wire mesh windows/doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.1mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steelsection made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and Inline sash adaptor(where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge. Wire mesh / Glazing of plain/ toughened/ laminated/ double glass unit with .Two track two panels sliding window with Aluminium channel for roller track, wool pile, nylon rollers with SS 304 body. Using R2 series with frame (40mm & above) x (40mm & above) & sash (25mm & above) x (50mm & above) with zinc alloy (zamak) powder coated touch locks with hook (Height upto 1.2 metre) |
| 13 | Repairing of Executive office computer work station cum work table of size-1500x900x750 in Room No-1515 OF Shakti Bhawan Extn. Building. Top surface finished with approved Quality 1 mm Thick sunmica laminate and interior faces finished with 10x20 mm thick sprit polish teak wood beading. One number lockable drawer and one lockable cupboard 400mm wide finished with1 mm Thick sunmica laminate. one no lock and one no handle fitted in drawer and cupboard & back side covered. The work include cost of all labour, material T&P required for proper completion of work. Please Enable Macros to View BoQ information |
