|
| 1 | Surface dressing n.exc 15 cm deep in soft/loose soil. |
| 2 | Excavation in trenches n. exc. 1.5m wide and n. exc. 1.5m depth for foundation and getting out in hard/dense soil complete. |
| 3 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and directed. |
| 4 | Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point As specified and directed. |
| 5 | M&L for Cement concrete PCC Type D-2 1:4:8(40 mm graded aggregate) in foundations,filling and mass concrete |
| 6 | M&L for reinforced cement concrete M-30 (Design Mix) using 20mm graded aggregate as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and as directed. |
| 7 | M&L for reinforced cement concrete M-30 (Design Mix) using 20mm graded aggregate as in Columns, pillars, piers, posts and struts complete all as specified and as directed. |
| 8 | M&L for reinforced cement concrete M-30 (Design Mix) using 20mm graded aggregate as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and as directed. |
| 9 | M&L Steel sheet form work to sides of concrete foundations, footings, bases of columns raft and beams sides and soffits(if any) of foundations and plinth,beams and similar work,vertical or to batter,for rough finished flat surfaces of concrete complete all as specified and as directed. |
| 10 | M&L Steel sheet form work to sides of pillars, posts, struts, piers, columns and stanchions, for square, rectangular or poygonal, rough finished surfaces of concrete complete all as specified and as directed. |
| 11 | M&L for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc rough finished surfaces of concrete complete all as specified and as directed. |
| 12 | M &L mild steel TMT bars 10mm dia and over cut to length, bent to shape required, including cranking bending spirally for hooping for columns hooking ends and binding with and including mild steel wire(annealed ) not less than 0.9mm dia or securing with clip complete all as specified and as directed. |
| 13 | M &L mild steel TMT bars 5mm dia and over upto and including 10mm dia as in stirrups, cut to length, bent to shape required, including cranking bending spirally for hooping for columns hooking ends and binding with and including mild steel wire(annealed ) not less than 0.9mm dia or securing with clip complete all as specified and as directed. |
| 14 | M&L for Pre-cast cement concrete block masonry Type C-1 (1:3:6) 20 mm graded aggregate with solid blocks, exc. 10 cm in width and setting in mortar |
| 15 | M&L for rendering 15 mm thick on fair faces of brick work or concrete in CM 1:4 and finishing the surfaces even and smooth (without using extra cement) as specified and directed. |
| 16 | Rendering 15mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 and to be finished even and smooth without using extra cement - Internal Plaster complete all as specified and directed. |
| 17 | M&L Hardcore of guage exc 63mm but n exc. 100 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rolled/rammed to a true surface in broken stone or boulders complete all as specified and directed. |
| 18 | M & L PCC type B-1 1:2:4 (20 mm graded aggregate) for fixing hold fast |
| 19 | S & F MS flat iron of size 25x3 mm as in hold fast conforimg to Fe 410-0 or Fe-310-0 |
| 20 | Plinth protection 75 mm thick in PCC type C1 1:3:6 (using 20 mm graded aggregate crushed stone aggregate) laid in alternate bays (not exc 2 Sqm each) finishing even smooth at top without using extra cement and providing joints throughout the thickness of plinth protectio, filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight all as specified and directed at site. |
| 21 | M&L for Cement Concrete type D-2, 1:4:8 (20 mm graded aggregate) 100mm thick as Sub base complete all as specified and directed. |
| 22 | M&L for 40mm thick Cement Concrete type B-1, 1:2:4 (20 mm graded aggregate) as in floor Sub base complete all as specified and directed. |
| 23 | M & L for coloured non-skid ceramic tiles 7 to 8 mm(square/rectangular) rea of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc 15 mm thick cement mortar screed bed or bedding layer in CM 1:6 complete all as specified and directed by Engr-in-charge. |
| 24 | M&L Glazed ceramic coloured tiles in vertical surface 450X 300X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match and joint free including 10 mm thick baking coat in CM 1:3. for laying floor finishes receiving floor tiles complete all as specified and directed by Engr-in-Charge. |
| 25 | S&F for 2nd Class soft wood plain, solid, straight chowkhats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified ans as directed. |
| 26 | M&L for 35mm 2nd class HW plain framed , panelled shutter (two panel) with lock rail and panel of 9mm B.W.P commerical ply or 12mm veneered particle board with commerical veneering on both faces. The size of rail and stile as per IS:1003 complete all as specified ans as directed. |
| 27 | S&F 100mm Butt hinges, medium weight, cold rolled mild steel, and fixed complete all as specified. |
| 28 | S&F 150mm Aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified. |
| 29 | S&F 150mm Aluminium handles, cast type, anodised complete all as specified. |
| 30 | S&F 300 mm aluminium alloy anodised sliding door bolt with hasp, staple complete all as specified. |
| 31 | S&F 150mm Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor |
| 32 | M&L 4 mm thick glass panes ordinary quality and glazing with oil putty in square n .exc 0.50 Sqm in each Pane etc complete |
| 33 | S&F Steel work in tubular/ rectangular/hallow section trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161 1979 grade St.-240 |
| 34 | S&F for Pre- painted galvatume aluminum zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as directed by Engr-in-Charge. |
| 35 | S&F for Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as directed by Engr-in-Charge. |
| 36 | M&L Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes etc. with riveted, bolted or welded attachment confirming to Fe 410-W (Gde E-250), complete all as directed by Engieer-in-charge. |
| 37 | Mild steel bolts neck exc 10 mm dia and n exc 15 mm dia, purpose made, with hexagonal or square head one end and screwed the other, or screwed both ends; each scre-wed end to be fitted with washers and one hexagonal or square nut, exc 5cm but n exc 10cm long |
| 38 | M & L for providing two coats of synthetic enamel painting to new wood or wood based surfaces of any description, not otherwise described over 10cm width or girth over a coat of pink primer including preparation of surfaces complete all as specified and directed . |
| 39 | Preparing of new surface of wall of any description and applying two coats of distemper oil emulion, with one coat of primer all as specified. |
| 40 | M&L for preparing new surfaces of plastered or unplastered and applying two coat of cement base paint over chalk whiting complete all as specified and directed by Engr-in-Charge. (Note : Ladders, scaffolding will be provided by Contractor where required) |
| 41 | M&L for preparation of new steel surfaces of any description over 10 cm width or girth not otherwise described and treating with two coats of synthetic enamel paints over a coat of red oxide primer. |
| 42 | S&F Rotational moulded water tank 1000 liter polye-thylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as spd and directed by engr in charge. |
| 43 | S&F 20 mm bore ball valves high pressure PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed. |
| 44 | S&F vitreous China squatting pan 'orrisa' pattern white colour of size 580x440mm with integral foot rests including provision of lime concrete including P/S traps. |
| 45 | S & F of PVC (Plastic polymer Cistern) low level white flushing cistern 10 litre capacity valve less, syphonic action type, complete with inlet, ball valve, float valve, bends, brackets, brass screws, handle etc and S & F of 32 mm dia PVC flush pipe of suitable length and making all connection complete all as specified and directed. |
| 46 | S&F 600mm x 450 mm bevelled edge mirror of selected quality glass mounted on 6 mm thick fixed on wall with wooden plugs with chromium plated brass screw & cup washer |
| 47 | S&F 15 mm dia bib tap chromium plated with cruth butterfly handle, screw down , screwed for iron pipe or brass ferrule. |
| 48 | S&F 75 mm dia PVC (SWR) pipe single socketed in any length with rubber ring joints, laid in trenches or fixed to wall complete as spd and directed. |
| 49 | S&F 75 mm dia PVC (SWR) bends any radius complete as spd and directed. |
| 50 | S&F 75 mm dia PVC (SWR) junction single, (single T) equal or unequal complete as spd and directed. |
| 51 | S&F 75 mm dia PVC (SWR) vent cowl |
| 52 | S&F 110mm dia bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to floors complete all as specified. |
| 53 | S&F 110 mm dia bore PVC (SWR) bends any radius |
| 54 | S&F 110 mm dia PVC (SWR) junction double, (double, T) equal or unequal complete as spd and directed. |
| 55 | S&F floor trap of PVC 75 mm out let dia with grating and jointed to waste pipe as spfd.complete all as specified and directed by engr-in-charge |
| 56 | S&F Wash basins, Vitreous China size 550 x 400mm (flat back or angle back type)any size, including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply including brackets, as spd and directed. |
| 57 | S&F Pillar taps, fancy type cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed, as spd and directed. |
| 58 | S&FStop valves 15 mm chromium plated fancy type caste copper alloy,screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed , as spd and directed. |
| 59 | S&F Glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and as directed. |
| 60 | S&F brass chromium plated tubular towel rail 20mm dia 600 mm long fixed complete all as specified and as directed. |
| 61 | S &F 25 mm dia 3-layer PP-R Polypropylene random copolymer concealed pipes SDR 7.4 (PN-16) UN stablized and antimicrobial fusion welded having thermal stability for hot & cold water supply all PP-R plain & brass threated polypropylene random fittings laid in trenches etc. |
| 62 | S&F 25 mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixe as spd and directed. |
| 63 | S&F PVC connections 15mm size with PTMT nuts of length 450mm as spd and directed. |
| 64 | M&L for plywood Veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on one faces; 6 mm thick fixed with nails to timber frame work complete as in ceiling complete all as spd & directed. |
| 65 | M&L second class hard wood timber scantling plain fillets square, rectangular or triangular in section, clean sawn, secured with nails or brads, sectional area exc. 6 Sq cm n.exc 13 Sq cm secured with nails or brads. |
| 66 | Excavation over areas n.exc 1.5m deep and and getting out in hard/dense soil complete all as specified and directed by Engr-in-Charge. |
| 67 | Excavation over areas exc 1.5m deep and n.exc 3.00 m deep and getting out in hard/dense soil complete all as specified and directed by Engr-in-Charge. |
| 68 | M&L for PCC 1:3:6 type C-2 (Nominal Mix) using 40 mm graded stone aggregate as in foundation filling mass concrete and similar work complete all as specified and as directed. |
| 69 | M&L for Walling of random rubble uncoursed, well bonded, bedded and solidly hearted, built in CM 1:6 complete all as specified and directed |
| 70 | M&L for Walling of random rubble stone masonary, uncoursed, well bonded, bedded and solidly hearted, laid dry complete all as specified and directed |
| 71 | M&L for providing RCC type B-1 1:2:4 using 20 mm graded aggregate in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like all as specified and directed. |
| 72 | M&L for rough finished Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) all as specified and directed. |
| 73 | Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roof n.exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10 cm but n.exc 20 cm wide complete all as specified and directed by Engr-in-Charge. |
| 74 | M&L TMT bars 6 to 8 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engr-in-Charge. |
| 75 | M&L for precast cement concrete 1:2:4 type B-1 using 20mm graded aggregate as in cover slab for manhole set in CM 1:4 including necessary form work complete all as specified and directed by Engr in Charge. |
| 76 | M&L for Plain cement concrete 1:3:6 type C-1 using 20mm graded crushed stone aggregate as in coping, benching bed plates and the line including necessary form work and finishing all exposed surface of concrete as per clause 4.11.16.2(a) of SSR Part-I (2009) complete all as specified and directed by Engr-in-Charge. |
| 77 | M & L for loose filling with broken bricks aggregates of gauge 80 to 150 mm in soakage pit, soakage wells complete all as specified and directed by Engr-in-Charge. |
| 78 | S&F 110mm dia bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to floors complete all as specified. |
| 79 | M&L Concrete bed 1:4:8 type D-2 to drain pipes incl packing under and haunching against the sides of pipes after they are laid and tested bore of pipe in 110 mmcomplete all as specified and directed by Engr-in-Charge. |
| 80 | Supply only Integral Water proofing compound complete all as specified and directed by Engr-in-Charge. |
| 81 | Taking down chowkhats or frame exc 1.50 sqm each but n exc 4 sqm each with shutters (without taking off shutters from the frame) complete all as specified and directed by Engr-in Charge |
| 82 | Taking down of chowkats with shutter (without taking of shutter from frame) n exc 1.5 Sqm each complete all as specified and directed by Engr-in-Charge. |
| 83 | M&L for preparation of old painted surfaces of wood or wood based material and applying one coat of synthetic enamel paint on surface of any description over 10cm width or girth complete all as specified and directed by Engr-in-Charge. |
| 84 | S&F 200mm Aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed |
| 85 | S&F 250 mm Aluminium alloy, anodised,sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed |
| 86 | Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed by Engr-in-Charge. |
| 87 | M&L for Dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing) removing dismantled tile and rubbish off the premises complete all as specified and directed by Engr-in-Charge. |
| 88 | M&L Non - skid Ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with 15 mm CM 1:4 sceed bed complete all as specified and directed by Engr-in-Charge. |
| 89 | M&Lin repair for 600mmx450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and as directed by Engr-in-Charge |
| 90 | S&Fin repair Vitreous China wash basin, white, pedestal type flat back, size 580x450irun include waste pipe, chain and plug and porcelain stopper but including brackets complete all as specified and directed by Engr-in-Charge |
| 91 | S&F in repairs vitreous china water closet (squatt pan) orrisa pattern 580x440 mm size pan white with front or back inlet with integral 'foot rests including provn of lime concrete bedding including connections to 'flushing cistern/pipe including 100mm PVC 'P' trap complete all as specified and directed by Engr-in-Charge |
| 92 | S&F in repair PVC 10 Ltrs valve less, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete with 32 mm dia flush pipe connecting to squatt pattern etc. ISI approved etc complete all as specified and directed by Engr-in-Charge. |
| 93 | S&F in repair vitreous China wash down (EWC) water closet pan (pedestal pattern), white (excluding flushing cistern and flush pipe) including seat cover for pedestal pattern complete all as specified and directed by Engr-in-Charge. (Make : Jaquar/Cera) |
| 94 | S&F in repairs PVC connections 15mm size with PTMT nuts of length 450 mm complete all as specified and directed by Engr-in-Charge |
| 95 | S&F in repair 15 mm bore bib tap brass chromium plated fancy type with crutch or butterfly handle screwed down, screwed for iron pipe complete all as specified and directed. |
| 96 | S&F in repairs 15mm bore pillar taps CP brass chromium plated fancy type screwed down high pressure with chromium plated screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed. |
| 97 | S&F in repairs 15 mm bore stop valves, cast copper alloy, fancy type, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed. |
| 98 | S&F in repairs 32 mm dia bore waste fittings brass chromium plated fixed to wash hand basin, sinks with long screwed shanks and fly nuts flange and bedded in red lead cement and other end fixed complete all as specified and directed. |
| 99 | S&F in repair 3 layer PP-R Polypropyene ransom copolymer outer dia of pipe 16 mm concealed pipes SDR 7.4 (PN-16) UV stabilzed and anti microbial fusionwelded having thermal stavility for hot & cold water supply including all PPR plain & brass threaded polypropylene random fittings fixed complete to wall s, ceilins or in floors etc.complete all as specified and directed by engr-in-charge |
| 100 | S&F in repair 3 layer PP-R Polypropyene ransom copolymer outer dia of pipe 25 mm concealed pipes SDR 7.4 (PN-16) UV stabilzed and anti microbial fusionwelded having thermal stavility for hot & cold water supply including all PPR plain & brass threaded polypropylene random fittings fixed complete to wall s, ceilins or in floors etc.complete all as specified and directed by engr-in-charge |
| 101 | S&F 150mm dia bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches/wall necessary excavation& haunching and including dismantling existing pipe line complete all as specified and directed by Engr-in-Charge. |
| 102 | M&L for PVC (SWR) 110 mm gully trap setting joining with solvent cement complete all as specified and directed. |
| 103 | Dismantling plain or corrugated steel sheeting any guage, thickness including nainital or similar pattern roof covering and wall cladding complete all as specified and directed by Engr-in-Charge |
| 104 | S&F 0.50 mm thick Galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with coach screws and washers, in roofs, walls etc. with grade of zinc coating 275.complete all as specified and directed by Engr-in-Charge |
| 105 | S&F 0.50 mm thick Plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 complete all as specified and directed by Engr-in-Charge |
| 106 | M&L preparation of steel Surfaces new untreated surface apply one coat of red oxide,zink chrome and two coat of synthetic enamel (ordinary tint) paint any description, over 10cm in width or girth,not otherwise described complete all as specified and directed by Engr-in-Charge |
| 107 | Demolition of Cement Concrete (Unreinforced) in ground floors and pavings n exc. 15cm thickness (below or above ground level), complete all as specified and directed by Engr-in-Charge. |
| 108 | M&L for preparation of old painted steel surfaces and applying one coat of synthetic enamel paint on surface of any description over 10cm width or girth complete all as specified and directed by Engr-in-Charge. |
| 109 | M&L for preparation old surfaces of plastered or unplastered old decorated surfaces of walls by brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat of white/lime wash on walls including cornices, pilasters etc complete all as specified and directed by Engr-in-Charge. |
| 110 | Taking down cement plaster on brick or stone etc including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed by Engr-in-Charge. |
| 111 | M&L for preparing old surfaces of plastered or unplastered surfaces including washing rubbing down and scrapping smoke soot moulds, moss and greasing sports with steel wire brush and applying two coat of cement base paint on wall complete all as specified & directed by the Engr-in-Charge. |
| 112 | Demolition of Brickwork / concrete block or stone/ boulder masonry, built in cement mortar complete all as specified and directed by Engr-in-Charge. |
| 113 | S&F in repair of 500 ltrs capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete all as specified and directed by Engr-in-Charge. |
| 114 | S&F in Repairs 200 mm long Aluminium, anodised, barrel tower bolt, fixed with screws complete all as specified and directed by Engr-in-Charge. |
| 115 | S&F in Repairs 150 mm size, Aluminium anodised handles fabricated type polished complete all as specified and directed by Engr-in-Charge. |
| 116 | S&F in Repairs 250 mm long, aluminium alloy,anodised,sliding door bolts, with hasp, staple (bolt type) and fixing clip of sheet, cast or extruded section and fixing bolt and sliding bolts of extruded section section or cast aluminium alloy complete all as specified and directed by Engr-in-Charge. |
| 117 | S&F in Repairs 15 mm bore Angle cock, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe and fixed.complete all as specified and directed by engr-in-charge |
| 118 | Taking up and down GI tubing and connection including cleaning for re-fixing or removing to store 20mm bore of pipe complete all as specified and directed by Engr-in-Charge. |
| 119 | Taking up and down GI tubing and connection including cleaning for re-fixing or removing to store 25mm bore of pipe complete all as specified and directed by Engr-in-Charge. |
| 120 | S&F 20 mm 3-layer PP-R Polypropylene random copolymer) concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc complete all as specified and directed by Engr-in-Charge. |
| 121 | S&F for 25mm PP-R Gate valves (brass insert) as per requirement of the site complete all as specified and directed by Engr-in-Charge. |
| 122 | Demolition and breaking up drain pipes (salt glazed ware, PVC or re-inforced concrete) set in cement mortar internal dia of pipe 100mm complete all as specified and directed by Engr-in-Charge. |
| 123 | M&L PCC 1:3:6 type C-2 as in 110mm bore of pipe in concrete bed to drain pipes including packing under and haunching against the sides of pips after they are laid and tested complete all as specified and directed by Engr-in-Charge. |
| 124 | S&F 110mm dia bore PVC (SWR) bends complete all as specified and directed.complete all as specified and directed by Engr-in-Charge. |
| 125 | S&F 110mm dia bore PVC (SWR) junction single(single T) equal or unequal complete all as specified and directed.complete all as specified and directed by Engr-in-Charge. |
| 126 | M&L for rendering 10 mm thick on fair face of brick work or concrete surfaces in CM 1:6 finished even and smooth wiithout using extra cement. |
| 127 | M&L for preparation of new plastered surfaces of wall and applying two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/ltrs and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm all as per the manufacturers instructions, complete all as specified and directed by Engr-in-charge. |
| 128 | M&L for preparation old surfaces of plastered or unplastered old decorated surfaces of walls by brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying two coats of oil bound distemper on walls including cornices, pilasters etc ccomplete all as specified and directed by Engr-in-Charge. |
| 129 | Complete removal of existing surfaces including washing rubbing down and scrapping for applying Two or more coats of 100% Premium acrylic emulsion paint on wall having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces. including Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete all as specified and directed by Engr-in -Charge. |
| 130 | M&L for preparation/removal of old painted steel surfaces and applying two coat of synthetic enamel paint on surface of any description over 10cm width or girth complete all as specified and directed by Engr-in-Charge. Please Enable Macros to View BoQ information |
| 131 | M&L for preparation/removal of old painted steel surfaces and applying two coat of synthetic enamel paint on surface of any description over 10cm width or girth complete all as specified and directed by Engr-in-Charge. Please Enable Macros to View BoQ information |
