|
| 1 | Demolition of cement concrete in floors and pavings n. exc 15 cm thickness below or above ground level, complete all as specified and directed. |
| 2 | M & L for 75 mm thick plain cement concrete (1:3:6) mix, type C-1 (using 20mm graded crushed stone aggregate) as in plinth protection, finishing the surfaces even and fair without using extra cement, including 10 mm wide, 75mm deep joints made at 3.00 m in length and filled with bitumen 85/25 grade and sand in the ratio 1:3 including necessary form work , complete all as specified and directed. |
| 3 | M & L for chipping removing carefully concrete work by low impact hammer, breakar without damaging the structure & cleaning and disposal of debries out side the premises etc complete all as specified and directed by Engr-in Charge. Hard concrete should not be removed by force. |
| 4 | M&L for Clean existing reinforcement with wire/ rotary wire brush making the surfaces free from loose material dirt etc complete, Applying two coats of alkaline rust converting primer FEOVERT of Krishna conchem or Dr. Fixit equivalent confirming to ASTM-B-117 on the rebars, including cleaning the reinforcement, wire brushing to remove loose rust spalls, with time interval of 6 hour between the coats and applying protective coating IPNET-RB complete all as specified and directed by Engr-in Charge. |
| 5 | M&L Carry out application of 'Bi-polar migratory corrosion inhibitor' EPCO-KP-100 or equivalent on concrete surface.complete all as specified and directed by Engr-in Charge. |
| 6 | M&L for Providing and applying structural grade EPIBOND-21-LP prior to application of any type of mortar plaster conferming to ASTM-C-882-91 (Arizona Slant Shear Test) to ensure bond between old concrete and new concrete complete all as specified and directed |
| 7 | M&L for Building up the profile of structural members by using latex additives(MONOBOND) modified air cured mortar system (Polymer modified mortar) (1:5:15 =1-MONOBOND, 5-Cement, 15-Sand) in damaged areas in 20mm thickness including leveling profiling etc complete all as specified and directed by Engr-in Charge. |
| 8 | M&L for Building up the profile of structural members by using latex additives(MONOBOND) modified air cured mortar system (Polymer modified mortar) (1:5:15 =1-MONOBOND, 5-Cement, 15-Sand) in damaged areas in 40mm thickness in two layers including leveling profiling etc complete all as specified and directed by Engr-in Charge. |
| 9 | Replacement of steel reinforcement with TMT bars of appropriate size where 20% of cross section is reduced including dismantling of rusted steel including application of rust converter FEOVERT and applying protective coating IPNET-RB complete all as specified and directed by Engr-in-Charge. |
| 10 | M & L for 10mm thick coloured vitrified ceramic tiles( light shade) (square/rectangular) polished area of each tiles not exceeding 0.36 sqm ,as in floors etc ,set and jointed in neat cement slurry and jointed in colour cement to match the tiles, over & including 15 mm thick rendering in cement mortar 1:6 complete all as specified and directed. |
| 11 | All as per item no 10 here-in-before including 10 mm thick cement screed bed in CM (1:4) but on vertical surface such as skirting/ risers etc complete all as specified and directed |
| 12 | M&L 20mm thick screed bed in CM 1:4 for tiles etc. complete all as specified and directed. |
| 13 | M&L Non skid coloured ceramic tiles of first quality jointless 400mmx400mmx7mm thick as in floor etc. set and jointed in neat cement slurry and pointed in coloured cement to match the existing surfaces complete all as specified and directed. |
| 14 | M&L for coloured glazed ceramic tiles of in verticle surface of size 300mm x 450mmX7 mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match,complete all as specified and directed. |
| 15 | M&L for 10mm thick bedding layers in cement mortar 1:4 complete all as specified and directed. |
| 16 | Dismantling floor hearth or wall tiling including cement mortar bedding, removing serviceable tile to store and rubbish off the premises. |
| 17 | Dismantling of brick work of any description and in any position built in cement or cement lime mortar including all quoins, arches, pillars including segregation of serviceable bricks for reuse & removal of rubbish out off from site etc complete all as specified and directed. |
| 18 | M& L for Brick work with sub class 'B' bricks straight or curved on plan to exe 6m mean radius built in cement mortar 1:6 complete all as specified and directed. |
| 19 | Taking down complete existing treatment of roof/ parapet , Mud puska on roof /parrapet including plastering, brick tiles, stone slabs and leeping any thickness including removal of rubbish from site etc complete all as specified and as directed. |
| 20 | M&L Plain cement concrete (1:2:4) Type B-0, using 12.5 mm graded stone aggregate as in padding to roof maintain the required slop and finished the surface without using extra cement, complete all as specified and as directed y Engineer In Charge. |
| 21 | M&L Rendering 10 mm thick in cement mortar 1:4 on concrete / brick surfaces with liquid water proofing compound @ 200 ml/50 kg per bag of cement or as per manufacturar instruction finished even and smooth without using extra cement over roof / sunken slab /wall complete all as specified and directed NOTE : water proofing liquid will be measured and paid seperately . |
| 22 | M&L for Water proofing treatment on \\"Non approachable / non accessible roof\\" surface (Horizontal & Vertical surfaces) by complete removel of existing old treatment and in following sequence through manufacturer / authorized applicator of the manufacturer all as specified and directed complete in sequence: (i) Applying approved bituminous based primer conforming to IS : 3384-1995 @ 0.3kg/Sqm to be applied on top surface of prepared surface till the surface is properly impregnated. (ii) Laying APP (Atactic polypropylene Polymer Modified preffabricated membrane) water proofing membrane of weight not less than 3 kg/sqm with minimum 100mm side overlap along the length from downward to upward completely sealed with torch application/hot blown lamps. (iii) Applying two cots of bituminous based aluminium paint @ 0.3 kg/Sqm complete all as specified and as directed. |
| 23 | Supply only integral water proofing compound. |
| 24 | Taking down cement plaster on brick walls built in cement mortar including raking out joints and concrete surfaces as in wall or ceiling etc. including hacking for key, scrubbing down with water etc complete all as specified and directed. |
| 25 | M&L for rendering 15 mm thick on brick masonry/concrete surface etc in cement mortar (1:4) surface finished even & smooth without using extra cement complete all as specified and directed. |
| 26 | M&L for rendering 10 mm thick cement plastering on fair face of brick masonry/concrete surface etc in cement mortar (1:6) surface finished even & smooth without using extra cement complete all as specified and directed. |
| 27 | M&L for 5 mm thick cement plastering in cement mortar 1:4 on concrete ceiling surfaces finished even & smooth without using extra cement omplete all as specifed and as directed. |
| 28 | M&L for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm with applcation of external putty after preparation of new plastered surfaces. |
| 29 | M&L for Preparation of new plastered or unplastered surfaces of walls and applying two coats of distemper oil emulsion over a coat of primer and 1mm thick putty complete all as specified and directed |
| 30 | M&L for Preparation of new plastered surface and applying two coat of distemper oil emulsion over 1mm thick coat of putty on ceiling surfaces complete all as specified and directed |
| 31 | M&L for complete removal of existing treatment from walls (any number of layers) by scrapping with steel scrappers or any other means, including filling depressions of scrapped surfaces with preparation of plastered surfaces and apply two coats of distemper oil emulsion (OBD) over a coat of primer and a layer of wall care putty (1.0 mm thick )complete all as specified and directed. |
| 32 | M&L for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm with applcation of external putty after complete removal of existing surfaces. |
| 33 | M&L for complete removal of existing treatment of walls and applying two coat of oil emulsion distemper over 1mm thck coat of putty complete all as specified and as directed. |
| 34 | Taking down chowkhats or frames of any description n exc 1.5 Sqm each (without taking off shutters from the frame) including cutting hole to size for receive fresh PCC of hold fast and making good the disturbed surface complete all as specified and directed. |
| 35 | Taking down chowkhats or frames of any description exc 1.5 Sqm and n. exc. 4 sqm each (without taking off shutters from the frame) including cutting hole to size for receive fresh PCC of hold fast and making good the disturbed surface complete all as specified and directed. |
| 36 | S&F for 1.25 mm thick pressed steel frames of size 125 mm x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc including plain cement concrete 1:3:6, type C-0 (using 12.5 mm graded crushed stone aggregate) as in filling in pressed steel door complete all as specified and directed.Note: The quoted unit rate under this item shall deemed to be included (i) one shop coat of primer (ii) a coat of bitumen paint of inner side of pressed steel door frame before filling of PCC. |
| 37 | S&F for 1.25 mm thick pressed steel frames of size 105 mm x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc including plain cement concrete 1:3:6, type C-0 (using 12.5 mm graded crushed stone aggregate) as in filling in pressed steel door complete all as specified and directed.Note: The quoted unit rate under this item shall deemed to be included (i) one shop coat of primer (ii) a coat of bitumen paint of inner side of pressed steel door frame before filling of PCC. |
| 38 | S&F 30mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both side. all as specified and directed. |
| 39 | S&F 35mm thick glazed and Skelton shutters, of 2nd class hard wood factory made, open rebated and prepared to receive glass, guage etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut or mitred beads for securing glass etc. (size of members of shutters as specified in SSR Part-I, Section 8, Clause 8.24 (a) complete all as specified and directed. |
| 40 | S&F Mild steel framed work such as grills,door framed,guard bars, railings etc. conforming to Fe-290 Gde-E-165 complete all as specified and directed. |
| 41 | S&F 2nd class HW small articles such as cleat / stopper for door / window incl all necessary laburs articles n. exc. 200 cu. cm each and fixed to chowkhats complete all as specified and as directed. |
| 42 | S & F solid PVC door frame of size 50mm X 47mm made out of 5mm plain colour PVC sheet reinforced with mild steel square tubes suppyling & fixing in opening as per specification & drawing complete all as spcefied and directed by Engineer-in-Charge. |
| 43 | S & F for factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tube for top and bottom rails. mild steel framed shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail &bottom rail on either side & as gap insert for top rail & bottom rail, paneling of plain colour PVC sheet to be fitted in the MS framed welded/sealed to stiles & rails with suitable PVC sheet beading & joined together with solvent cement complete all as fixing in the frame at site as per specification and drawing complete all as specified and as directed. |
| 44 | S&F powder coated (with coating layer of minimum 50 micron thick) aluminium frame for doors, windows, ventilators shutters(fixed/ sliding track two or three track) and partitions frames with extruded built up standard sections of approved make fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions with sealent with wall, i.e. at top, bottom and sides including cleat angle, C.P. brass/ stainless steel screws, all complete all as specified and directed. |
| 45 | S & F for powder coated aluminium window , ventilator shutters/sliding shutter with coating layer of minimum 50 micron, Track channel or fixed type without sash bar, aluminum section weighing min 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified. |
| 46 | M & L 25 mm thick PCC type B - 1 1:2:4 using 12.5 mm graded stone aggregate as in flooring finish even & smooth using extra cement complete all as specified and as directed. |
| 47 | M&L PCC 1:2:4 type B-1 using 20mm graded stone aggregate as in hold fast complete all as specified and directed . |
| 48 | S&F Preparation of new wood or wood based surfaces and applying two coats of synthetic enamel paint over a coat of pink primer on surfaces exc 10 cm in width or girth complete all as specified. |
| 49 | S&F Preparation of old painted surfaces and applying one coat of synthetic enamel paint on wood surfaces of any description not otherwise decribed over exc. 10 cm in width or girth complete all as specified. |
| 50 | S&F Preparation of new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified and directed. |
| 51 | S & F Aluminium anodised handles of extruded section and fixed 125 mm long complete all as specified & directed. |
| 52 | S&F Mild steel helical door spring of size 150mm including roller and roller plate fixing to iron frame by welding all as directed. |
| 53 | S & F 150 mm (overall length of cover plate) floor door stopper with rubber shoes aluminium alloy body and tongue, anodised ,with hard drawn steel spring,fixed in floor complete all as specified and directed. |
| 54 | S & F Aluminium anodised barrel tower bolts of extruded section and fixed 200 mm long complete all as specified & directed. |
| 55 | S&F 250 mm long aluminium alloy, anodised,sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed. |
| 56 | S & F for butt hinges extruded aluminium alloy with galvanised steel hinge pin , anodised type B-21 complete all as specified and directed |
| 57 | S & F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks or galvanised wire staples etc complete all as specified & directed. |
| 58 | M & L for 4 mm thick plain sheet glass ordinary quality and glazing with oil putty not exceeding 0.50 Sqm in each pane,complete all as specified and as directed by Engineer-in-Charge . |
| 59 | S & F in repair 20 mm dia curtains rod of chromium plated mild steel tubing with fixing for fancy type brackets,stops, rollers etc.,complete all as specified and as directed by Engineer-in-Charge. Note: Running length of curtain rod shall be measured & paid only. |
| 60 | S&F in repairs brass CP bracket fancy type suitable for fixing type with brackets and fixed complete all as specified and directed. |
| 61 | S&F in repair 18/19mm thick pre-laminated particle board interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination for cupboard shutter, shelf, etc complete all as specified and as directed. |
| 62 | S & F for 30 mm width of flaps (when open) continuous (piano) hinges,mild steel, bright finish or electrogalvanised complete all as specified and directed. |
| 63 | S&F 40mm dia cupboard knobs fixed with nut, screw and washer of mild steel with brass polish,bright finish complete all as specified and directed |
| 64 | S&F ball catcher with 8mm dia steel ball and brass body and striking plate including letting and fixed complete all as specified and directed |
| 65 | S&F 125 mm size of hasp and staple safety type aluminium anodized hinges pin including bolt to hinges plate complete etc all as specified & directed. |
| 66 | Taking up or down steel tubing and connections of 15 mm bore or removal to store complete etc and making good the surface in cement mortar 1:3 complete all as specified & directed.all as specified & directed. |
| 67 | S&F for GI water tubing medium grade, ISI marked, galvanised, 15 mm bore with all fittings, (such as tee, elbow, socket, union & short pieces) fixed to walls and ceiling or laid in floors including cutting chases for brick walls and making good the surface in cement mortar 1:3 complete all as specified & directed. |
| 68 | Refixing/re-laying for 15 mm bore old steel tubing and connections in new or old position (Walls, ceiling,floors, etc.)including all fitting as socket, elbow, nipple,union etc complete all as specified and directed .Note :G I Pipe obtained from item No.66 here-in -before. |
| 69 | Taking up or down steel tubing and connections of 20 mm bore or removal to store complete etc and making good the surface in cement mortar 1:3 complete all as specified & directed.all as specified & directed. |
| 70 | S&F for GI water tubing medium grade, ISI marked, galvanised, 20 mm bore with all fittings, (such as tee, elbow, socket, union & short pieces) fixed to walls and ceiling or laid in floors including cutting chases for brick walls and making good the surface in cement mortar 1:3 complete all as specified & directed. |
| 71 | Refixing/re-laying for 20 mm bore old steel tubing and connections in new or old position (Walls, ceiling,floors, etc.)including all fitting as socket, elbow, nipple,union etc complete all as specified and directed .Note :G I Pipe obtained from item No.66 here-in -before. |
| 72 | S&F for PVC connection 15 mm dia size with PTMT nuts of length 450 mm complete all as specified and directed. |
| 73 | S&F in repair 15mm bore long body (weight not less than 400 gm) bib tap, cast copper alloy, CP fancy type with crutch or butterfly handle, screw down, screwed for iron pipe or for brass ferrule including flange complete all as specified and directed |
| 74 | S & F shelf of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats 450mm long and 150mm wide (minimum weight 300gms) complete all as specified and directed. |
| 75 | S&F rotational moulded polythene water storage tank of capacity 1000 ltrs (Cylindrical/vertical with closed type), triple layer construction, ISI marked, hoisted and fixed in position including 20 mm bore GI nipple and 25 mm bore ball/ float valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (minimum weight 455 gms) including taking down/dismantling of existing tank complete all as specified and directed. |
| 76 | S & F Ball brass valve, high pressure with polythene float and fly nut complete screwed for iron pipe or brass ferrule and fixed to dia of pipe 20mm as in repairs, complete all as specified and directed. |
| 77 | M&L for plain cement concrete 1:3:6 type C-2 (using 40 mm graded crushed stone aggregate) as in base of PVC tank etc including necessary form work complete all as specified and directed. |
| 78 | S&F in repair stop valve/cock 20mm bore chromium plated fancy type with long shank fancy type cast copper alloy, screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for brass ferrule fixed in wall etc complete all as specified and directed. |
| 79 | S&F Angle stop cock fancy type, brass chromium plated with CP wall cap 15 mm bore after taking down of old brass stop valve complete all as specified. |
| 80 | S & F stop cock of 15mm bore , chromium plated with long shank ( concealed type) and cup concealed type cast copper alloy, screwed down, high pressure, with crutch handle, screwed both ends for brass ferrule, complete all as specified and directed. |
| 81 | Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings,heads, shoes, bends, swan-necks,etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specifed & directied. |
| 82 | S & F 110 mm dia PVC rain water pipes single socketed in any length with rubber ring joits fixed to walls with and including stack clamps made out of 40mm by 3mm flat iron and 12mm dia round iron stays and making good the disturbed portion in CM 1:3 to match with surrounding area, complete all as specified and directed. |
| 83 | S&F in repair PVC (SWR) bends 110 mm dia PVC pipes with rubber ring joints complete all as specified & directed. |
| 84 | S & F for 110 mm bore, PVC (SWR) pipes, single socketed, in any length, with rubber ring joints laid in trenches or floors complete all as specified & directed. |
| 85 | S & F for 75 mm bore, PVC (SWR) pipes, single socketed, in any length, with rubber ring joints fixed to walls complete all as specified & directed. |
| 86 | S & F for 75 mm bore, PVC (SWR) pipes, single socketed, in any length, with rubber ring joints laid in trenches or floors complete all as specified & directed. |
| 87 | S & F vitreous China wash basin, flat back size 550 mm X 400 mm including 32mm brass chromium plated waste coupling , 32 mm bore PVC waste pipe, chromium plated Grating including cutting for & pinning in ends of bracket or errecting bracket ,fixing of pillar tap & PCC 1:2:4 ,type B-1(using 20 mm graded crushed stone aggregate) for embedding brackets & making good disturbed surface with CM 1:3 complete all as specified and directed. |
| 88 | M&L for 100 mm thick plain cement concrete 1:4:8, type D-2 (using 40 mm graded crushed stone aggregate) as in sub base to flooring/hard standing etc ,complete all as specified and directed. |
| 89 | M & L for sand filling under floor or in foundations including watering and consolidation complete as specified and directed. |
| 90 | M&L for 80mm thick factory made machine pressed pre-cast concrete interlocking paver block of approved shade of any shape and size conforming to IS-15658-2006 of M-40 grade laid over & including cleaned dry sand cushion bed 50mm thick over & including 100 mm thick PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as sub-base, surface finished even and rough over and including 75mm thick Hardcore of broken boulder of gauge n exc. 63mm, deposited, spread and levelled, watered and rammed to a true surface, etc complete all as specified and directed. |
| 91 | M&L for plain cement concrete 1:2:4, type B-1 (using 20 mm graded crushed stone aggregates) as in kerb/benching/copings including weathering, slightly rounded or chamfered angle and throating including use & waste of necessary form work etc complete all as specified and directed |
| 92 | S & F pillar taps long body chromium plated, cast copper alloy with capstan head, chromium plated, screwed down with or without lettered 'Hot' or 'Cold' with long screw shanks and fly nuts, screwed for iron pipe and fixed for 15 mm bore complete all as specified & directed (Make- Shakti Cat Part No API-6108 or equivalent Cat Part No. of any make as per appendix 'A' to P.S as approved by GE). |
| 93 | S & F brass chromium plated shower rose with swivel joints, 50 mm size in square with CP long shank arm including fixing to steel pipe or union complete all as specifed & as directed. |
| 94 | S & F PVC flushing cistern 10 ltr capacity valve less syphonic action type low level with and including ball valve float and handle, PVC flush pipe 32 mm bore & PVC connection 15 mm bore 450 mm long with PTMT nuts and brackets complete set & making good disturbed surface with CM 1:3 complete all as specified and directed. |
| 95 | S & F 600mm X 450 mm bevelled edge looking mirror of selected quality glass mounted on 6 mm thick Acbuilding board or commercial plywood and fixed to wooden plugs with CP brass screw and cup washers complete all as specified and directed. |
| 96 | S&F for vitreous china, squatting pan \\" Orissa Pattern\\" of size 580 mm X 440 mm white with integral foot rest including cast iron \\"P\\" or \\"S\\" trap, front or back inlet and making connection to trap & to flushing cistern complete including taking down existing pan & making good disturbed surface complete all as specified & directed. |
| 97 | S&F brass chromium plated towel rail , 20 mm dia ,D-type 600 mm long between flanges fixed with and including chromium plated brass screw & wooden /plastic cleats complete set all as specified and directed. |
| 98 | S & F PVC (SWR) bends 75mm bore of any radius complete all as specified and directed |
| 99 | S & F PVC (SWR) 110mm bore branch piece, double (double- Y) equal or unequal complete all as specified and directed |
| 100 | S & F PVC (SWR) 75mm bore branch piece, double (double Y) equal or unequal complete all as specified and directed |
| 101 | S&F 110 mm bore PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed. |
| 102 | S&F 75 mm bore PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed. |
| 103 | S&F 110 mm bore PVC (SWR) junction double, (double T) equal or unequal complete all as specified and directed. |
| 104 | S&F 75 mm bore PVC (SWR) junction double, (double T) equal or unequal complete all as specified and directed. |
| 105 | S & F 110 mm bore PVC (SWR) vent cowl with rubber ring joints complete all as specified and directed. |
| 106 | S & F 110 mm dia PVC(SWR) WC connector with lip ring, complete all as directed and as specified. |
| 107 | S & F for 75mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement with chromium plated grating with or without hole complete all as specified and directed. |
| 108 | Taking down carefully unserveciable/damaged copper/aluminium surface (batten/coduit or casing caping) point wiring any length for light/fan/socket or power including unscrewing from board (fitting and fixture such as switches, sockets, ceiling rose, lamp holders, brackets, pendent, regulators, sockets ,light fittings etc) and removing material from site and making good to the disturbed surface to match with existing finish etc complete all as specified and directed. |
| 109 | Taking down ceiling fan/exhaust fan of any sweep after disconnecting all necessary electrical connctions from ceiling rose to fan, fan blade and deposit to MES store yard of AGE E/M Ramgarh complete all as specified and directed. |
| 110 | Taking down old/unserviceable distribution board by disconnection of electric connection carefully SPN DBs/ TPN DBs/Main Switch including old unserviveable MCCBs/ MCBs, Isolators, etc and making good to distrurbed surface all as specidied and directed at site. |
| 111 | Taking down carefully copper/aluminium Sub main wiring of any size from surface/ concealed/ existing conduit of any height and removing materials at site and making good disturbed surfces of walls , floors roofs etc complete as specified and directed. |
| 112 | Taking down of existing geyser of any capacity after disconnecting all necessary electrical and water supply connections and deposit to MES store yard of AGE E/M complete all as specified and as directed. |
| 113 | Taking down earthing system of any type any size complete as specified and directed. |
| 114 | M&L for point wiring for one light/fan point /exhaust fan controlled by one , one way switch with using with FRLSH PVC insulated PVC unsheathed electric cable conforming to IS:694, 1100V grade AC, single core having multi stranded copper conductor of size 1.5 Sq.mm nominal cross sectional area for phase & neutral and including non metallic rigid PVC conduit ISI marked medium grade not less than 20 mm dia with all conduit accessories in concealed wiring system & 1.5 Sqmm green PVC insulated unsheathed multistranded copper conductor as a earth wire connected to earth dolly by providing lugs including sunken type anodized pressed steel sheet terminal box covered for mounting fittings/junction boxes including PVC board with bakelite sheet 2.8 mm thick laminated cover make sheet for housing/ fixing switches etc., including cutting holes for switches,sockets,regulators etc as per requirement including fixing with machine screw,washer etc complete all as specified and directed. Note: Proper colour coding to be adopted. |
| 115 | All as per item No. 114 here-in-before but one light point controlled by one, one way switch 5 Amps complete all as specified & directed. |
| 116 | All as per item No.114 here in before but one ceiling/Exhaust fan point controlled by one, one way switch 5 Amps complete all as specified & directed. |
| 117 | All as per item No. 114 here-in-before but one 5 Amps socket outlet on same board complete all as specified & directed. |
| 118 | All as per item No. 114 here-in-before but one 5 Amps socket outlet on independent board complete all as specified & directed. |
| 119 | All as per item No. 114 here in before but one bell/buzzer point controlled by one push button on independent with cable 1.5 sq. mm size complete all as specified & directed. |
| 120 | All as per item No. 114 above with 2.5 sqmm (nominal area) FRLSH cable PVC for 15 Amps 3/5 pin socket power point including 2.5 sqmm copper conductor green as colour for earth contineuity complete all as specified & directed. |
| 121 | S&F switch modular single pole one way 6 amp 240 volts, 1 module complete all as specified & directed. |
| 122 | S&F switch modular single pole one way 16 amp 240 volts, 1 module complete all as specified & directed. |
| 123 | S&F Modular single socket 6A - 2/3 pin combined 2 module complete all as specified & directed. |
| 124 | S&F modular socket 16A - 2/3 pin combined 2 module. |
| 125 | S&F Bell push modular 6 Amps single module complete all as specified |
| 126 | S&F Bell Electric ding dong type suitable for operation on 230 volt 50 Hz AC supply complete all as specified and as directed |
| 127 | S&F Ceiling rose 3 terminals PVC/Polycarbonate, isolated body, ISI marked complete all as specified and directed. |
| 128 | S&F steped type modular fan regulator, 120 W, 2 module complete all as specified & directed. |
| 129 | Refixing ceiling fan/exhaust fan after overhauling by cleaning/greasing /oiling etc. including provision of connecting ceiling fan/exhaust fan to ceiling rose including three core flexible copper cable of size 1.5 sqmm not less than 0.5 mtr long for connection and preparation of old rusted surface of ceiling fans of any sweep by cleaning to remove only dust etc. and applying one coat of synthetic enamel (white shade) paint and marking MES number with non erasable marker pen with black colour complete all as specified & directed by Engineer-in-charge. |
| 130 | Refixing of geyser capacity 25/50 ltrs, retrived from item no 112 including acessories complet e maintenance/ overhaul of geyser by cleaning tank, heating element & tightening of electical connections etc. complete all as specified and as directed. |
| 131 | S & F steel body Exhaust fan of 300 mm sweep blade with louvers shutter , frame single phase ,230 V,50 Hz,900 RPM AC ,copper winding, including provision of hole, mounting frame, nut, bolts, washer, fasteners etc and connecting exhaust fan to ceiling rose including provision of three core flexible copper cable of size 1.5 sqmm not less than 0.5 mtr long for connection complete all as specified & directed. |
| 132 | S & F LED light fitting 1 x 20watt , 220 V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose to fitting, complete all as specified and as directed by Engr-in-Charge. Make: Havells/Bajaj/Crompton Greaves/Phillips. |
| 133 | S&F LED light fitting with high out put diffuser 2 feet, 10 watt 220 V AC with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed by Engineer-in-Charge |
| 134 | S & F lamp holder, PVC/Polycarbonate type with back plate having matching colour to holder suitable for angle/batten fittings (ISI marked), complete all as specified. |
| 135 | S & F LED bulb of capacity 9 watt , lumen out put (950)lm ,length 113 mm dia 60 mm , base cap B22 (ISI mark) complete all as specified and as directed by Engr-in-Charge. Make:HavellsCat Part No. LHLDERHEML8X015 or in equivalent Bajaj/Philips/Crompton Greaves |
| 136 | S & F landscape cylindrical shape LED bollard light 10 watt IP66 with integrated driver, incluing establishing on ground connecting to the existing cable and make it functional all as specified and directed at site. |
| 137 | S & F building security lights with new generation energy saving & environment friendly long life versattle pressure dia cast aluminium IP-65 road luminarie with high power LED as light source & exclisively designed polycarbonate cover alongwith electronic driver type street light fitting 35 watt capacity LED including all accessories duly pre-wired,fixing on existing bracket with nut,bolt & washer etc as required at site for fixing of street light on pole/wall complete including taking down existing street light fitting any type complete all as specified & directed. |
| 138 | S&F in repair for distribution board (DB) made out of steel sheet metal enclosure (CRCA sheet) dust and vermin proof Triple pole and neutral(TPN) 4 way IP 43 (double door) with 200 Amps rated copper bus bar neutral bar ,earth bar 415 Volts ,flush to wall including taking down carefully existing unserveciable /old main switches, DBS along with MCBs complete all as specified and directed. |
| 139 | S&F in repair 415V, 10KA 'B' curve miniature circuit breaker (MCB) of triple poles and neutral (TPN) and current carrying capacity 40 to 100 Amp with breaking capacity 10 kA,in the DB with connection testing and commissioning complete all as specified and as directed. |
| 140 | S & F in repair sheet metal enclosures powder coated for DBs when MCBs to used single pole and neutral (SPN) double door 240 volts, 4 way with IP-43 IK-09 protection including 200 Amp bus bar and neutral link (ISI marked) EARTH BAR & DIN RAIL confirm to IS:13032-1991 DB complete all as specified and as directed. |
| 141 | S&F in repair 240V, 10KA 'B' curve miniature circuit breaker (MCB) of single poles & neutral (SPN) and current carrying capacity 32 Amp with breaking capacity 10 KA ,in the MCB DB with connection testing and commissioning complete all as specified and as directed. |
| 142 | S&F in repair 240V, 10KA 'B' curve miniature circuit breaker (MCB) of single poles (SP) and current carrying capacity 5 amp to 32 Amp with breaking capacity 10 KA ,in the MCB DB with connection testing and commissioning complete all as specified and as directed. |
| 143 | M & L Sub main wiring with two runs of single core 6.0 Sqmm PVC insulated FRLSH multistanderd copper conductor cable and one run of 6.0 Sqmm PVC insulated unsheathed FRLSH multi stranded copper conductor cable for earth wire drawn in & including concealed rigid non metallic PVC conduit medium grade with fittings (ISI marked) not less than 25 mm dia/appropriate dia with accessories & fittings complete and making good disturbed surface wall including taking down existing sub main wiring complete all as specified and as directed. Note : - Two runs of 6.0 Sqmm cable and one run of earth wire 6.0 sqmm & conduit shall be measured as one unit length and extra length of cable required for connection to MCBs shall be deemed to be include in unit rate quoted by bidder. |
| 144 | M & L Sub main wiring with two runs of single core 4.0 Sqmm PVC insulated FRLSH multistanderd copper conductor cable and one run of 6.0 Sqmm PVC insulated unsheathed FRLSH multi stranded copper conductor cable for earth wire drawn in & including concealed rigid non metallic PVC conduit medium grade with fittings (ISI marked) not less than 20 mm dia/appropriate dia with accessories & fittings complete and making good disturbed surface wall including taking down existing sub main wiring complete all as specified and as directed. Note : - 1. Two runs of 4.0 Sqmm cable and one run of earth wire 4.0 sqmm & conduit shall be measured as one unit length and extra length of cable required for connection to MCBs shall be deemed to be include in unit rate quoted by bidder. 2. Extra length of cable required for connection to MCBs shall deemed to be inlcuded in unit rate) |
| 145 | Supply and laying or fixing or passing though pipe, 1100 volts grade heavy duty cable with XLPE insulated aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC shealthed 50 sq. mm 3.5 core nominal cross section including testing complete all as specified and as directed. |
| 146 | Excavation in trenches not exceeding 1.50 metre wide and not exceeding 1.50 metre in depth for cable trenches and getting out in soft/ loose soil complete all as specified and as directed |
| 147 | Returning, filling in trenches including spreading, levelling, watering and well ramming in layers not exceeding 25 cm in soft/ loose soil complete all as specified and as directed |
| 148 | Removing excavated materials to distance not exceeding 50 metre and depositing where directed at a level not exceeding 1.5 metre above the starting point all as specified and as directed. |
| 149 | Material and labour for supplying and laying reinforced pre cast concrete cable concrete cable cover class LV, Type - 1, flate, size 250 mm x 150 mm x 40 mm complete all as specified and as directed. |
| 150 | Material and labour for sand cushioning for protection of underground cable, consolidated and compared with clean dry sand all as specified and as directed.(Note: The depth of sand shall be measured after punning only) |
| 151 | M & L earthing complete with Gl electrode 600 mm x 600 mm x 6.00mm thick buried directly in ground vertically in pit of depth not less than 2.25 mtr below normal ground level with top edge of the earth plate not less than 1.50 mtr below normal ground level connected to Gl earth strip 32 mm X 6mm(up to 7.5 mtr length on earth plate) as earthing lead by means of bolts, nuts, check nuts and washer of galvanized iron or steel including excavation and earth work and disposal of surplus soil including 40 mm dia Gl tubing light grade and necessary fitting for protection of Gl strip including laying of charcoal, dust and common salt PCC (1:3:6) type C-l( using 20 mm graded crushed stone aggregate) earth pit with 40x40x6mm mild steel angle iron frame & 50mm thick pre cast RCC cover (1:2:4) type B-1 (using 20 mm graded crushed stone aggregate) reinforced with 8mm dia TMT bars @ 10mm C/C both way with mild steel handle 10 mm dia round bars ,10mm thick plastering with cement mortar (1:4) internally and upt0o 150 mm below ground level externally, PGI funnel with wire mesh 20mm dia Gl pipe for watering complete all as shown on electrical plate No.3 of SSR Part -1 2009 and connected in earth testing point including testing cincluding taking down old/ unserveciable existing earthing & making good disturbed surface of wall ,floors etc.complete all as directed. Notes: -(i) Earth lead & protection pipes length upto & including 7.50 metre. (ii) Earth filling shall be done by vegetable soil. (iii) Soil should be free from stone, boulders, aggregate, gravels etc. |
| 152 | M&L for laying GI tubing laid in trenches and on wall/surface light grade 40 mm dia with all fitting for cable protection including GI clamps nut bolts and washer etc all as specified. Please Enable Macros to View BoQ information |
