|
| 1 | Dismantling old plaster and pointing in cement or lime and raking out joints to 15mm depth, watering and disposalof unserviceable materials with all leads all complete as per direction of E/I |
| 2 | Providing 6mm thick cement plaster (1:4) in ceiling with clean of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I. |
| 3 | Dismantling patent stone floor including stacking serviceable materials in countable stacks within 15M. Lead and disposal of unserviceable materials with all leads all complete as per direction of E/I |
| 4 | Providing 12mm cement plaster (1:4) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I. |
| 5 | Dismantling R.C.C. work including stacking serviceable materials in countable stacks within 15M. Lead and disposal of unserviceable materials with all leads all complete as per direction of E/I. |
| 6 | Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing:1:1½:3 (1 cement : 1½ coarse sand (zone-III) : 3 graded stone aggregate 20 mmB.C.D. S.O.R. Item No. 5.3.2.1 |
| 7 | Reinforceemnt cement concrete work in beams, suspended floors, roofs having slope up to 15º landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral staircase above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 |
| 8 | Providing and laying APP (Atactic polypropylene polymer) modified refabricated five layer 3mm thick water proofing membrane, black finished reinforced with non - woven polyester matt consisting of acoat of bitumen primer for bitumen membrane @ 0.40 litre/sqm by the same membrane manufacture of density at 25°C, 0.87- 0.89 kg/litre and viscocity 70-160 cps. Over the primer coat the layer of membrane shall be laid using Butane Torch and sealing all jointsetc, and preparing the surface complete. The vital physical and chemical parameters of the membrane shall be as under :Jointstrength in longitunal and transverse direction at 23°c as 650/450N/5cm. Tear strength in longitudinal and transverse direction as 300/250N. Softening point of membrane mot less than 150°C. Coldflexibility shall be upto - 2°C When tested in accordance with ASTM,D - 5147. The laying of membrane shall be got done through theauthorised applicator of the manufacturer of membrane :3mm thick. ITEM 14.90 DSR |
| 9 | Providing TMT steel reinforcement as per approved design and drawing excluding carriage of M.S bar to work site, all complete as per building specification and direction of E/I.B.C.D. S.O.R. Item No. 5.5.5 A |
| 10 | Taking down old door and window shutters including stacking serviceable materials within 15M,. Lead and disposal of unserviceable materials with all leads all complete as per direction of E/I.BCD 5.10.10 |
| 11 | S/F M.S. grill made of 20 x 6mm M.S. flat as per approved design and drawing, properly fabricated with joints continous fillet welded and finished smooth, carriage of grill to work site, hoisting as per building specification and direction ofE/I. (Where materials is not supplied by the deptt.) |
| 12 | Supplying fitting and fixing 20 gauge G.C.I. Sheet (Door & Window) gate on M.S.angle frame of size 60*60*6mm, including cost of fabrication providing necessary locking arrangements worth haskel and domny duly fixed in C.C. (1:2:4) blocks of required size. |
| 13 | Providing and laying Doublecharge vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622 / ISO 13006 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc,complete. Size of Tile 600x600 mm .B.C.D Item No. 5.6.28 |
| 14 | Providing and laying 6mm precast white glazed tiles in walls over 12mm cement mortar (1:3) and jointed with grey cement slurry flush pointing with white cement including rubbing, polishing and cost of curring taxes and royalty all complete as per building specification and direction and E/I. With commercial grade colour 15X15cm Tiles.B.C.D. Item No. 5.6.23.4 |
| 15 | Supplying, fitting and fixing collapsible gate of approved size and make properly fabricated with vertical double channels 20 x 10 x 2mm at 100mm centers and braced with M.S. flat diagonals 20 x 3mm with top and bottom rails of T.iron 40 x 40 x 6mm with 38mm dia steel pulleys complete with bolts, nuts, locking arrangement, stoppers,handles, including applying a priming coat of red lead paint, car riage, hoisting and taxes all complete as per building specification and direction of E/IB.C.D. S.O.R. Item No. 5.5.14 |
| 16 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved mak+B50e conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed Portion : Powder coated aluminium (minimum thickness of powder coating 50 micron)D.S.R. Item No. 21.1.1.2 |
| 17 | For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron)D.S.R. Item No. 21.1.2.2 |
| 18 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 4.0 mm thickness (weight not less than 10 kg/ sqm)D.S.R. Item No. 21.3.1 |
| 19 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately). 30 mm thickD.S.R. Item No. 26.87.1 |
| 20 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.D.S.R. Item No. 13.80 |
| 21 | Finishing wall with textured exterior paint of required shade New work ( Two or more coats applied @ 3.28ltr/10sqm) over and including primer coat of exterior primer applied @ 2.2./10sqm DSR item no.13.45.1 |
| 22 | Providing two coats of oil bound distemper of approved shade and make over a coat of cement primer over new surface including preparing the plastered surface by rubbing smooth with pumice stone or fine sand paper, applying putty where required, scaffolding, washing of floors and taxes all complete as per specification and direction of E/I.B.C.D. S.O.R. Item No. 5.8.18 |
| 23 | Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade : New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm).D.S.R. Item No. 13.47.1 |
| 24 | Providing primer one coat of red lead paint of approved make over new steel surface including preparing the surface after cleaning, removing dust, dirt, scales smokes and grease and cleaning the surface throughly including cost of scaffolding and taxes all complete as per building specification and direction of E/I. (Mode of measurement area shall be multiplied by the co-efficient as indicated in building specification.B.C.D. S.O.R. Item No. 5.8.41 |
| 25 | Providing two coat of painting with ready mixed paint of approved shade and make over steel surface including cleaning the surface throughly, scaffolding and taxes all after removing dirt including scales smokes, grease and sand papering including cost of scaffolding and taxes all complete as per building specification and direction of E/I.B.C.D. S.O.R. Item No. 5.8.43 |
| 26 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.B.C.D. S.O.R. Item No. 5.3.8 |
| 27 | Providing 250mm wide brick drain in cement mortar (1:6) with av. 150mm clear depth and 250mm apron including cost of eartwork involved with 75mm cement concrete (1:4:3) over one brick designation 75A flat soling in proper grade and slope at the base the drain duly plastered in C.M. (1:3) with punning over exposed surface all complete as per building specification and direction of E/I.S.O.R. Item No. 5.10.33 |
| 28 | Supplying, fining and fixing viterous white glazed earthen ware I.W.C of Parry Hindustan or any other I.S.S approved make with 100mm H.C.I \\"p\\" trap 15 liters C.I. or C. pull and let go flushing cistern of names or other I.S.S equivalent make, complete with all fittings. C.I or C.C brackets 32mm alkathene/P.V.C telescopic flush, pipe about 2M long with one brass coupling and clamps G.I chain and pull including supplying and fixing a pair of viterous white glazed earthenware where footrest to be fixed in floor 15 mm C.I body brass spindle stope cock of weight not less than 50 grins. 15 mm P.V.C connection pipe 450mm long and the exposed pipe and cistern with two coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/I.580mm Long with 15 litre low level P.V.C. cistern |
| 29 | Supplying, fitting and fitting vitreous white glazed earthen ware wash hand basin of Parry or Hindustan or any other I.S.S. approved make supported on pointed C.I. or M.S. brackets 32m C.I. brass waste, 15mm dia C.I. body brass spindle stop cock of approved quality of weight not less than 350 grams, 32mm P.V.C. waste pipe 750mm long with brass coupling at one end and making plumber joints etc. all complete as per specification and direction of E/I. |
| 30 | Providing and fixing male ended 15mm dia brass bib cock of approved quality (wt. not less than 350 grams) with extra socket all complete as per specification and direction of E/I. |
| 31 | Supplying, fitting and fixing the following items with all materials as per specification and direction of E/I.C.P. brass dish container medium quality with screw and hinges |
| 32 | Providing and fixing PTMT extension nipple for water tank pipe, fittings of approved quality and colour.15 mm nominal bore, weighing not less than 32 gms |
| 33 | Supplying, fitting and fixing the following items with all materials as per specification and direction of E/I.Mirrors of 6mm thick plate glass bevelled edge mirror including C.P. brass revolving fitting, 3mm plywood board and C.P. hinges to fix with mirror, 600 x 450mm size |
| 34 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.Flexible pipe - 32mm dia |
| 35 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110 mm diameter |
| 36 | Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.Single tee with door - 110 x 110 x 110mm |
| 37 | 110mm Bend 87.5° |
| 38 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.Concealed work, including cutting chases and making good the walls etc.15mm nominal dia Pipes |
| 39 | 20mm nominal dia Pipes |
| 40 | 32mm nominal dia Pipes |
| 41 | Supplying materials and labours for construction of inspection chamber of designation class 75B brick size 750mm deco, 650x450mm internal dimension having 250mm all thickness in cement plaster (1:4) with punning on inside and cement plaster (1:6) with 600x475mm G.I. cover with frame (weight not less than 36 kg.) along with earth work in excavation and refilling all complete as per specification and direction of E/I. |
| 42 | Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms. |
| 43 | Supplying and fixing 100mm (4\\") steel jali |
| 44 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 45 | Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete. 10 litre capacity - WhiteD.S.R. Item No. 17.18.1 |
| 46 | Providing and fixing uplasticised PVC connection pipe with brass unions : 45 cm length, 20 mm nominal boreD.S.R. Item No. 18.21.2.2 |
| 47 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.32mm dia Flexible pipeD.S.R. Item No. 17.28.2.1 |
| 48 | Supplying, fitting and fitting vitreous white glazed earthen ware wash hand basin of Parry or Hindustan or any other I.S.S. approved make supported on pointed C.I. or M.S. brackets 32m C.I. brass waste, 15mm dia C.I. body brass spindle stop cock of approved quality of weight not less than 350 grams, 32mm P.V.C. waste pipe 750mm long with brass coupling at one end and making plumber joints etc. all complete as per specification and direction of E/I.D.W. & S. Item No. 3.2.5 |
| 49 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm,including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink without drain board, 610x460 mm bowl depth 200 mm.D.S.R. Item No. 17.10.2.2 |
| 50 | Providing and fixing male ended 15mm dia brass bib cock of approved quality (wt. not less than 350 grams) with extra socket all complete as per specification and direction of E/I.D.W. & S. Item No. 3.1.5.1 |
| 51 | Providing and fixing 15mm dia brass stop cock of approved quality all complete as per specification and direction of E/I.D.W. & S. Item No. 3.1.6 A (d) |
| 52 | Supplying and fixing gun metal full way valve of approved quality all complete as per specification and direction of E/I.32mm dia and weight not less than 700 gramsD.W. & S. Item No. 3.1.12 d |
| 53 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.D.S.R. Item No. 18.920 mm dia |
| 54 | 25 mm dia |
| 55 | 32 mm dia |
| 56 | Supplying labour and equipments including 200mm dia. M.S. Cap and fitting and fixing over the tube well properly and taking it out as per direction of E/I.(M1036 : DW&S) |
| 57 | Supplying all tools, labours, equipments for lowering 32mm dia P.V.C. pipe in 3 mtr. length in the drilling bore of tube well etc. all complete job as per direction of E/I.D.S.R. 18.9.4 |
| 58 | Development of tube well in accordance with IS : 2800 (part I) and IS:11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, all as per requirement and direction of Engineer-in-charge.(M1042 : DW&S) |
| 59 | Supplying fitting and fixing of KSB/KIRLOSKER/CRI make 1.50 HP Submersible pump set having head of 135 metre including all taxes, royalty, etc.all complete job as per direction of E/I.(M1055 : DW&S) |
| 60 | Supplying fitting and fixing of 5 H.P. standard make starter panel board with arrangement of all necessary protection including all taxes,royalty etc all comlete job as per direction of E/I.(M1065 : DW&S) |
| 61 | Supplying all materials, labour & equipments for constructing P.C.C. (1:2:4) circular platform around each drilled tube well including 12mm thick cement plaster (1:4) with neat cement punning over exposed surface as per UNICEF design etc. all complete.(M1045 : DW&S) |
| 62 | Supplying fitting and fixing 3 core 4mm2 flat copper submersible cable FINOLEX/HAVELS make including all taxes,royalty etc all complete job as per direction of E/I.(M1906 : DW&S) |
| 63 | Wiring for light point/fan point/exhaust fan point/call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface /recessed PVC conduit, with modular switch, modular plate suitable GI box and the point with 1.5 sq mm FR PVC insulated copper conductor single core cable etc. as required.(GROUP-A) |
| 64 | wiring for ligh/power plug with 2x4 sq.mm FR PVC insulated,copper conductor,single core cable in and surface/recessed PVC conduitalong with 1 no. 4 sq mm FR PVC insulated copper conductor single core cable for loop earthing as required. |
| 65 | Wiring for circuit/sub main wiring alongwith earth wire with the following sizes of PVC insulated, copper conductor single core cable in and surface/recessedPVC coduit as required.2x1.5sqmm+1x1.5sq mm earth wire |
| 66 | 2x2.5sqmm+1x2.5sq mm earth wire |
| 67 | S/F 3 pin.5amp. Ceilling rose on the existing junction box/wooden block including connection etc.as reqd. |
| 68 | S/F brass battan/angle holder including connection etc.as reqd. |
| 69 | S/F of following sizes of PVC conduit alongwith the accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required . 20 mm PVC coduit. |
| 70 | 25 mm PVC coduit. |
| 71 | Suppling and fixing following piano type switch / socket on the existing switch box / cover including connection etc. as reqd.5/6 amps switch |
| 72 | 5/6 amps socket outlet |
| 73 | S/F PVC/GI box of following sizes on surface or in recesses with suitable size of phenolic laminated sheet cover infront including painting etc.210 mm x 206 mm x48 mm deep(10\\"x12\\") |
| 74 | 72mmx146mmx48mm deep(4\\"x7\\") |
| 75 | Supplying and fixing of following way single pole & neutral, sheet steel , MCB distribution board 240 volts, on surface /recess , complete with tinned copper bushbars ,neutral busbar, earth bar , din bar ,detachable gland plate , interconnections ,phosphatized and powder painted including earthing etc. as requried. (but without MCB/RCCB/ISOLATOR) (2+8 way double door) |
| 76 | 48\\"(1200mm) ceiling fan |
| 77 | Fan regulator |
| 78 | 9/10 watts led bulb |
| 79 | 10/12 watts tubelight fitting(led) |
| 80 | Carriage of materialsSand |
| 81 | Stone chips |
| 82 | Cement |
| 83 | steel |
| 84 | Add 18% G.S.T |
| 85 | Add 1% L.C. Please Enable Macros to View BoQ information |
