|
| 1 | Taking down chowkhats or frames with shutters without taking off shutters from the frame exceeding 1.5 Sqm but not exceeding 4 Sqm each and all as specified . |
| 2 | S&F Solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with M S square tubes , S&F in opening as per specification & drawing given in SSR-2022. complete all as specified and directed by Engr-in-Charge. |
| 3 | S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M S tubes for top & bottom rails M S frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width struck in side with solvent cement for stiles and plain colour PVC sheets 5 mm thick for top rail, lock rail & bottom rail on either side & as gap insert for tap rail & bottom rail, paneling of plain colour PVC sheets to be fitted in the MS frame walded/sealed to the stiles & rails with suitable PVC sheet beading and joined to getger with solvent cement supplying & filling in the frame at site as per specification & drawing given in SSR-2009 complete all as specified and directed by Engr-in-Charge. |
| 4 | S&F 100 mm long butt hinges extruded aluminium alloy with galvanised mild steel hinges pin, anodised and fixed complete all as specified and directed by Engr-in-Charge. |
| 5 | S&F 150 mm long aluminium handle cast type anodized all as specified complete all as specified and directed by Engr-in-Charge. |
| 6 | S&F 200 mm long aluminium anodised barrel tower bolt of extruded section and fixed complete all as specified and directed by Engr-in-Charge. |
| 7 | M&L for Brick work with old size burnt fly ash bricks, straight or curved on plan exceeding 6 mtr mean radius built in CM 1:6 all as specified and Including demolition of stone, brick masonry built in cement mortar incl quoins, arches, etc but exceeding ashlar facing dressed stone Work complete all as specified and directed by Engr-in-Charge. |
| 8 | M&L for rendering 15mm thick (in two layer of 10mm+5mm) on brick or concrete/stone surfaces in cement mortar 1:4 surface finished even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge. Note:- Necessary additional dubbing if required will be done by contractor and nothing extra cost is admissible in this account. |
| 9 | M&L for rendering 15 mm thick (in two layer of 10mm+5mm) on brick or concrete/stone surfaces in cement mortar 1:6 surface finished even and smooth w/o using extra cement complete all as specified and directed by Engr-in-Charge. Note:- Necessary additional dubbing if required will be done by contractor and nothing extra cost is admissible in this account. |
| 10 | M&L for rendering 15mm thick (in two layer of 10mm+5mm) on brick or concrete/stone surfaces in cement mortar 1:4 surface finished even and smooth without using extra cement complete all as specified, including Taking down cement plaster from stone/brick walls, racking out joints hacking for key, scrubbing down with water etc complete all as specified and directed by Engr-in-Charge. Note:- Necessary additional dubbing if required will be done by contractor and nothing extra cost is admissible in this account. |
| 11 | M&L for rendering 15mm thick (in two layer of 10mm+5mm) on brick or concrete/stone surfaces in cement mortar 1:6 surface finished even and smooth w/o using extra cement complete all as specified and as directed, including Taking down cement plaster from stone/brick walls, racking out joints hacking for key, scrubbing down with water etc complete all as specified and directed by Engr-in-Charge. Note:- Necessary additional dubbing if required will be done by contractor and nothing extra cost is admissible in this account. |
| 12 | M&L for rendering 5mm thick on fair faces of concrete surfaces in cement mortar 1:3 on ceiling etc, finishing the surface and even and smooth without using extra Cement complete & including taking down cement plaster from stone/brick walls, racking out joints hacking for key, scrubbing down with water etc complete all as specified and directed by Engr-in-Charge. |
| 13 | Supply only Liquid water proofing compound |
| 14 | M&L for preparation of new plastered surfaces or un plastered, previously undecorated wall surfaces and applying applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10sqm over and including 2mm thick wall care putty, complete all as specified and directed. |
| 15 | M&L for preparation and applying two coats of oil bound distemper on newly plastered surfaces of wall over a coat of primer including 3mm thick wall putty complete all as specified and directed by Engr-in-Charge. |
| 16 | M&L for preparation and applying three coats of white wash on newly plastered surface as in ceiling complete all as specified and as directed. |
| 17 | Preparation of old decorated plastered or unplastered surfaces including cleaning by brooming down or with steel wire brushing scraping down smoke soot, moulded moss and efflorescent salts and treating oil and greasy spots and applying one coat of distemper oil emulsion on walls as specified. |
| 18 | Preparation of old decorated plastered or unplastered surfaces including cleaning by brooming down or with steel wire brushing scraping down smoke soot, moulded moss and efflorescent salts and treating oil and greasy spots and applying two coats of distemper oil emulsion over 3mm thick wall care putty on walls, complete all as specified. |
| 19 | Exterior Painting work including complete removal of existing treatment till top surface of existing plaster and crack filling with crack seal upto 3mm where required and making good/smooth the surface with wall putty with silicon additives and sanding these surface for removal of loose particles and applying one coat of water proof primer on walls and chajjas with 10% dilution of water and applying two coats of 100% acrylic smooth emulsion exterior grade with silicon additives and anti-algal properties, complete all as specified. |
| 20 | Preparation of old decorated plastered or unplastered surfaces including cleaning by brooming down or with steel wire brushing scraping down smoke soot, moulded moss and efflorescent salts and treating oil and greasy spots and applying one coat of cement base paint on walls as specified. |
| 21 | M&L for preparation of old painted wood or wooden based surfaces by rubbing with abrasive paper etc of any description over 10cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed by Engr-in-Charge. |
| 22 | M&L for preparation of old painted steel and iron surfaces by rubbing with abrasive paper etc of any description over 10cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed by Engr-in-Charge. |
| 23 | M&L for Mat finish, premium quality, joint free (edge cut), coloured/ printed Non -Skid ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile not exceeding 0.38 sqm, as in floors etc. set and jointed in neat cement slurry over 15mm thick bedding layer in cement mortar (1:4) including necessary cutting and waste as per site requirement pointed in white or coloured cement to match, including dismentling floor, hearth or wall tiling including cement mortar bedding complete all as specified and directed by Engr-in-Charge Size/Shade/Colour of tile shall be approved by the AGE(I). |
| 24 | M&L for Vitrified Ceramic tiles 10 mm thick (square/rectangular), dark shade, polished, area of each tiles exc 0.36 sqm , in floors over 15mm thick screed bed or bedding layer of CM (1:6) etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match. including dismentling floor, hearth or wall tiling including cement mortar bedding complete all as specified and directed by Engr-in-Charge Size/Shade/Colour of tile shall be approved by the AGE(I). |
| 25 | M&L for Glazed ceramic coloured tiles of size 450mm x 350 mm x 7 mm thick as in vertical surfaces, set and jointed in neat cement slurry and pointed with white or coloured cement to match the shade of tile over 10 mm thick cement plaster in cement mortar 1:3 including dismentling floor, hearth or wall tiling including cement mortar bedding complete all as specified and directed by Engr-in-Charge Size/Shade/Colour of tile shall be approved by the AGE(I). |
| 26 | M&L for granite (of any type) work (table rubbed and polished) 20mm thick in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including dismentling of existing granite including cement mortar bedding complete all as specified and directed.complete all as specified and directed by Engr-in-Charge. |
| 27 | M&L for cutting , rounding of edges and mirror polishing, of granite /marble/kota stone complete all as specified and directed by Engineer in charge. |
| 28 | M&L for reinforce cement concrete (Nominal Mix) 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in slabs supported on walls etc. including demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) of any description and in any position not otherwise specifically and disposal of unserviceable material, debris and rubbish to a distance not exceeding 100m complete all as specified and directed by Engr-in-Charge. |
| 29 | M&L for form work to soffits of suspended slabs n exc 200mm thick (Horizontal or sloping) rough finished surfaces of concrete complete all as specified and directed by Engr-in-Charge. |
| 30 | M&L for formwork to edges of concrete floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work n exc 10cm wide rough finished surfaces of concrete complete all as specified and directed by Engr-in-Charge. |
| 31 | S&F mild steel TMT bars 10mm and over, cut to length, bent to shape required, including cranking, bending spirally hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed. |
| 32 | S&F in repair sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm (including waste pipe and waste coupling), complete all as specified and directed by Engr-in-Charge. |
| 33 | Taking down existing IWC/EWC along with its cement concrete beadding and P or S trap and S&F one/single piece Vitreous china water closest white colour of size 750 x 665 x 360 mm including an inbuilt syphonic action type flusing cistern 10 liter capacity with seat cover and PVC pipe upto finish floor level to connect flush pipe, making good all the disturbed surface of floor to matcing the adjoining complete all as specified and directed by Engr-in-Charge. |
| 34 | S&F in repairs, self cleaning water jet, chromium plated, Fancey Type high qualitey (Health Faucet) 15 mm bore ABC Body mild steel CP with 1.25 mtr ong flexible tube and ABS wall hook including making connections and fixied complete all as specified and directed by Engr-in-Charge. |
| 35 | S&F in repair Vitreous China wash hand basin, white, flat back, size 550x400mm with pedestal excluding taps, waste coupling, chain and plug and porcelain stopper but including brackets complete all as specified and directed by Engr-in-Charge. |
| 36 | S&F in repair PVC valveless syphonic action type low level flushing cistern 10ltr capacity white with all internal fittings and CP handles knob/push including brackets PVC connection 45cm long including nut and PVC washer at both ends with brass chromium plated coupling 32mm bore including 32mm bore PVC long bend flush pipe 90cm long, complete all as specified and directed by Engr-in-Charge. |
| 37 | S&F in repair CP Stop valve/Angle valve 15mm bore cast copper alloy with crutch and butter fly handle screwed down high pressure,screwed both ends for pipe or for unions complete all as specified and directed by Engr-in-Charge. |
| 38 | S&F in repair CP Bib tap, 15mm dia, cast copper alloy with crutch or butter fly handle screwed down, screwed for iron pipe or brass ferrule and fixed in repair all as specifiedscrewed for iron pipe or brass ferrule complete all as specified |
| 39 | S&F in repair CP tubular towel rail, 20mm dia, D type, 60cm long between flangescomplete all as specified and directed by Engr-in-Charge. |
| 40 | S&F in repair 15 mm bore PVC connection with PTMT of length 450 mm complete all as specified and directed by Engr-in-Charge. |
| 41 | S&F in repair 15 mm bore brass CP shower rose 125 mm size and complete all as specified and directed by Engr-in-Charge. |
| 42 | S&F GI tubes medium grade 15mm dia, with all fittings and fixed complete to walls and ceiling or laid in floors & Including taking up or down steel tubing of 15mm bore and connections complete all as specified and directed by Engr-in-Charge. |
| 43 | S&F GI tubes medium grade 20mm dia, with all fittings and fixed complete to walls and ceiling or laid in floors & including taking up or down steel tubing of 20mm bore and connections complete all as specified and directed by Engr-in-Charge. |
| 44 | M&L for cutting chases, pinning in making good to facing where required and pointed in CM 1:3 to ends or edge of landing, steps cills, sunshade, shelves etc and cutting chases for concealed water tubing in stone concrete block or slab walls etc and making good cutting n exc 10 cm girth complete all as specified and directed by Engr-in-Charge. |
| 45 | S&F for rotational moulded High Density Poly-Ethylene water storage tanks of capacity 1000 litre and conforming to IS, hoisted and fixed in position and Includiing dismantling of water tanks capacity 1000 ltrs and removing from the site or to store complete all as specified and directed by Engr-in-Charge. |
| 46 | S&F in repair ball valves suitable for 20 mm bore iron pipe high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball, screwed for iron pipe and fixed. (minimum weight 210 gms) complete all as specified and directed by Engr-in-Charge. |
| 47 | S&F in repair 110 mm bore PVC (SWR), waste and vent pipe in any length with or without ears, Single socketed in any length with rubber ring joints , laid in trenches or in floors and fixed to walls etc complete all as specified and directed by Engr-in-Charge. |
| 48 | S&F in repair 75 mm bore PVC (SWR), waste and vent pipe in any length with or without ears, Single socketed in any length with rubber ring joints , laid in trenches or in floors and fixed to walls etc complete all as specified and directed by Engr-in-Charge. |
| 49 | S&F 110 mm bore PVC bends with including for all necessary extra joints cuttings and waste to any radius complete all as specified and directed. |
| 50 | S&F 75 mm bore PVC bends with including for all necessary extra joints cuttings and waste to any radius complete all as specified and directed. |
| 51 | S&F in repair 600 x 450 mm bevelled edges mirror 5 mm thick of selected quality glass, mounted on 6 mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated screw and cup washers complete all as specified. |
| 52 | S&F for 3mm thick plain sheet glass ordinary quality and glazing with oil putty or beading etc in square not exceeding 0.5 sqm in each pane including hacking out old broken glass (any thickness, size, quality or description) from fame complete all as specified and directed by Engr-in-Charge. |
| 53 | S&F in repair 25 mm dia drapery curtain rod with decorative end knobs complete with brackets and fixed to walls complete all as specified & directed by Engineer -in-charge. |
| 54 | S&F in repair diameter of outlet in 75 mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed by Engr-in-Charge. |
| 55 | S&F PVC connection both side brass unions internal for size 15mm dia and 450mm long complete all as specified and directed by Engr-in-Charge. |
| 56 | S&F in repair stainless steel plate rack of size of 900 mm x 775 mm x 250 mm made out of 1 mm thick stainless steel of first quality complete all as specified and directed by Engineer-in-Charge. |
| 57 | S&F for Brass CP mixer for mixing hot & cold water screwed down for iron pipe (Two in one wall mixer/ central hole basin mixer / sink mixer with swinging spout) and fixed complete all as specified and directed by Engr-in-Charge. |
| 58 | S&F sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed by Engr-in-Charge. |
| 59 | S&F toilet papar holder coloured, vitreous China, box type complete all as specified and directed by Engr-in-Charge. |
| 60 | S&F in repair for Soap dish, vitreous China white, approximate size 160x 160x90mm, any type fixed to plugs with chromuum plated complete all as specified and directed by Engr-in-Charge. |
| 61 | Taking down chowkats or frames with shutters (with out taking off shutters from the frame) not exceeding 1.50 Sqm each complete all as specified and directed by Engr-in-Charge. |
| 62 | S&F powder coated anodised aluminium frame for doors, window, ventilators and partition wall with with one or more rebate including joiing cleat for fixing etc, making good all the disturbed surface of floor/wall to mathing the adjoining complete all as specified and directed by Engr-in-Charge. |
| 63 | S&F powder coated anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 No.). hinges type B-21 100mm long (2 No.) suitable handle (1 No.) & tower bolt 02 nos each shutter, making good all the disturbed surface of floor/wall to mathing the adjoining complete all as specified and directed by Engr-in-Charge. |
| 64 | S&F powder coated anodised aluminium ventilators with 4mm thick frosted glass louvers and incl 0.36mm dia and 1.18mm aperture stainless steel jally (Fixed outside of ventilator) complete all as specified and directed by Engr-in-Charge. |
| 65 | S&F anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, complete all as per requirement and directed by Engineer-in-charge. |
| 66 | S&F galvanised stinless steel wire cloth, 0.51 mm to 0.56 mm nominal dia of wire and average width of aperture 1.18mm fixed with tinned tacks, or galvanised wire staples, complete all as specified and directed by Engr-in-Charge. |
| 67 | S&F 4.8mm thick sheet glass square n. exc. 0.5sq.m in each pane complete all as specified and directed by Engr-in-Charge. |
| 68 | M&L for demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) of any description and in any position not otherwise specifically and disposal of unserviceable material, debris and rubbish to a distance not exceeding 100m complete all as specified and directed by Engr-in-Charge. |
| 69 | M&L for compound girders and stanchions, lattice girders, channel, angle, or tee sections aerial masts, staging for water tanks and the like including caps, bases, splices etc. built up from two or more beam or channel sections or angles with plates, including all lattice bars, stiffeners, gusset plates,Fe 410 -W (Gde- E- 250) quality A etc complete all as specified and directed by Engr-in-Charge. |
| 70 | M&L for preparation of new steel and iron surfaces and applying two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by Engr-in-Charge. |
| 71 | S&F 18mm thick PVC sheet having one side decorative laminated sheet all required brackets SS screws etc. the panel shall be fabricated using adhesive and screws where ever required.all the edges shall be covered with 2mm thick edge bonding tape or 90 degree edge bent finish as per make and specification including fitting i.e. Piano hinges, magnetic catcher,stainless & steel handle for each leaf as required all are as approved by Engineer -in-Charge complete all as specified and directed by Engr-in-Charge. Please Enable Macros to View BoQ information |
