|
| 1 | M & L for cutting down the branches and Grubbing up tree trunk including cutting of trunk portion protruding over ground, digging out roots, filling holes and leveling off ground, stacking of serviceable material and removing of unserviceable material to a distance not exceeding 50 m and clearing site (girth exceeding 30 cm and not exceeding. 100cm) |
| 2 | Dismantling structural steel work including doors, gates but excluding framed truss etc |
| 3 | Dismantling of Asbestos cement (corrugated,semicorrugated, etc.) sheets in roof coverings |
| 4 | Dismantling of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings |
| 5 | Demolition of Brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles |
| 6 | Takin down Chowkhats or frames not exc. 1.5 sq. m each but with shutters (without taking off shutters from the frames) and removing to or from store. |
| 7 | Takin down Chowkhats or frames exc. 1.5 sq. m not exceeding 4 sq.m with shutters (without taking off shutters from the frames) and removing to or from store. |
| 8 | S & F of II class hard wood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed |
| 9 | S & F of II class hard wood Plain, framed, panelled shutters 40mm thick(any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats |
| 10 | S & F Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 |
| 11 | S&F of butt hinges length (125mm) cast, brass with mild steel hinge pin,bright polished and fixed but type B-12 |
| 12 | S&F of Aluminium handles length (150 mm), cast type, anodised |
| 13 | S & F of Aluminium alloy 250 mm length, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed |
| 14 | S & F of 200mm Aluminum barrel tower bolts of extruded section and fixed |
| 15 | S & F of Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded |
| 16 | S & F of 4mm thick Sheet glass, ordinary quality and glazing with oil putty in square exceeding 0.5 sq. m in each pane |
| 17 | S & F of Welded steel wire fabric weight per square meter not exceeding 4 kgs supplied and fixed complete to wood or steel members |
| 18 | Material & Labour for Brickwork with subclass ‘B’ bricks, with cement motor 1:6 straight or curved on plan exc 6m mean radius built in |
| 19 | Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc |
| 20 | Hacking out plastering 15 cm vide on either side of the crack cutting of 6mm 'V' groove by inserting chicken mesh in gaps of wall PU filler material of reputed companies such as (mastered builder solution, Fosroc. Alchemica, Dr Fixit), or suitably equivalent make and finishing to the original shape as directed. The crack filling shall be carried out as per the OEM specifications specified by the OEM and the material to be used shall be freshly manfacured having a minimum life span of six months when brough out site. |
| 21 | Material & labour for plastering in CM 1:4 15 mm thick on fair faces of brick work including all works. |
| 22 | M & L for Cement concrete of 40mm thick type B-0,1:2:4 (12.5mm graded aggregate) |
| 23 | M & L for white washing on wall (undecorated surfaces) with two coats including preparation of old surfaces. |
| 24 | M & L for cement plastering CM 1:4 10mm thick on fair faces of brick work or concrete surfaces. |
| 25 | S & F of 0.63mm thickness Plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 |
| 26 | M & L for structural steel of Fe 410-W (grade E 250) quality A Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete. |
| 27 | M & L for painting to steel surfaces of any description, over 10cm in width or girth,with two coats of synthatic enamel paint over a coat of red oxide, Zinc Chrome primer including preparing old surfaces. |
| 28 | M & L for painting to steel surfaces of any description, over 10cm in width or girth,with two coats of synthatic enamel paint over a coat of red oxide, zinc Chrome primer including preparing new surfaces. |
| 29 | Demolition of Unreinforced Cement Concrete structure of any description and in any position not otherwise specially provided. |
| 30 | Earthwork in excavating hard/dense soil in trenches, width and depth not exceeding 1.50m and getting out. |
| 31 | M&L for sand filling under floors or in foundations including watering and consolidation. |
| 32 | M & L for P.C.C 1:4:8 type D2 using 40mm graded aggregates for foundations |
| 33 | M & L for cement concrete in foundations, filling and mass concrete type B1 1:2:4 using 20mm graded aggregate. |
| 34 | Forming 25 mm width expansion joint in concrete slab for full depth of PQC. Early entry saw and subsequent cutting by using diamond bit cutter of appropriate size, straight and smooth edges. Joint cleaned thoroughly with application of compressed air. Joint shall be made dry, vacuum cleaned and free of dirt, oil, vegetation and other debris. The joint then filled with pre-molded 25 mm thick compressible polyethylene closed cell type filler board as specified, thereafter application of two coats of primer with thin brush by forward and backward movement at an interval of 30 minutes before placing the backup rod and pouring the sealant. Placing of closed cell, medium density, crossed linked polyethylene foam backup rod of 30 mm dia, over filler board and filled with polyurethane based sealant complying with BS- 5212, BS 4254 and EN-141gzc-2003 with minimum movement accommodation factor (MAF) of+/- 30% having minimum 10 year performance guarantee, applying masked tape on the edges of joints and removing the masking tape after filling of sealant as per the method specified by the manufacturer complete as specified and directed |
| 35 | Removal of excavated soil exceeding 250 m but not exceeding 500 m and depositing where directed |
| 36 | Removing excavated material rocks exceeding 1.50 km but not exceeding 5 km and depositing where directed. |
| 37 | Supply and fixing Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20amps MCB( Make :Legrand / Havells/ Anchor or suitable equivalent make) |
| 38 | Supply and fixing and connecting to the system sheet metal enclosures with double door DB’s when MCB’s to be used Triple pole & neutral 4 way,415V with 200 Amps rated busbar,( Make :Legrand / Havells/ ABB or suitable equivalent make) |
| 39 | Supply and fixing 415V 10KA 'C' curve MCB of TPN 40 To 100 AMP in the MCB DB complete with connection testing and commissioning. (Make :Legrand / Havells/ C&S or suitable equivalent make) |
| 40 | Supply and fixing 415V 10KA 'B' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the DB complete with connection testing and commissioning. TP 25 To 63 AMP( Make :ABB/Legrand / Havells/ Hager or suitable equivalent make) |
| 41 | Supply and fixing 240 Volt, 10KA 'C' curve MCB of Single Pole 6 To 32 Ampsin the MCB DB complete with connection testing and commissioning.( Make :Legrand / Havells/ C&S or suitable equivalent make) |
| 42 | Supply & Fixing of Wiring for circuit/sub main wiring along with earth wire with the following sizes of FR PVC insulated copper conductor, single core cable in surface/ recessed as required in STEEL conduit( Make :Havells/Finolex/Orbit/Policab or suitable equivalent make) a) 4x2.5 sqmm + 1x2.5 sqmm earth wire |
| 43 | Materials & labour for XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 3.5 core 25/sq.mm, U.G.cable with XLPE insulated aluminium conductor,( Make :Havells/Finolex/Orbit/Policab or suitable equivalent make) |
| 44 | Supply and fixing LED Flood light fitting 70 Watt 230 V AC outdoor type high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete. ( Make :Havells/Philips/ Wipro/ Bajaj/CG/Luker or suitable equivalent make). Please Enable Macros to View BoQ information |
