|
| 1 | Chipping & removing old cement plastered surface including racking out joints & clearing the surface for replastering & disposal of the debris as per directions within a distance of 150 m. |
| 2 | Demolishing C.C/ R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of engineer - in- charge. |
| 3 | Dismantling existing old sanittary fittings like wash basin, EWC, Urinal etc and removing all internal water lines and waste lines carefully without damaging the building as instructed at site from 2 toilet blocks |
| 4 | Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in charge.In cement mortar. |
| 5 | Chipping & removing mosaic flooring / skirting in the toilet rooms and other areas very carefully without damaging the remaining portions and water supply items and removing the debris to places pointed out by the department. |
| 6 | Scrapping old paint and Cleaning all surface by cleaning with sand paper or other mechanical devices to remove old paint coat and opening crack by grinder in 'V' shape up to 3mm, cleaning, 1 coat primer & filling all cracks by crack seal, finishing , Cleaning the surround surface etc. as per manufacturer specification. |
| 7 | Painting one coat of priming coat on plastered surface (interior/exterior) with approved quality cement primer after cleaning the surface including all cost of materials, labour etc. |
| 8 | Painting two coats with ready mixed plastic emulsion paint of approved quality and colour specified over the priming coat already done and paid separately after cleaning the surface well. |
| 9 | Cement block masonry work in CM 1:6 using good quality, approved cement blocks including charges for conveying, scaffolding charges etc. as per departmental instructions for super structure walls up to floor five level, excluding cost of cement. |
| 10 | Cement concrete work in 1:1½:3 nominal mix using 20 mm and downgrade hard granite broken stone including all charges for mixing concrete, laying, consolidating,curing etc.complete but excluding cost of form work & reinforcement works- For foundation footings, bottom & sides of trenches, equipment foundations, plinth beams, lintels, slabs, columns & beams etc.up to floor five level excluding cost of cement. |
| 11 | Waterproofing of Bathroom/ toilet floor:i) Surface preparation by cleaning the surface using wire brush in order to remove all deleterious matters and cleaning with water jet spray (if required) including removing old worn out tar felt, deleterious materials etc.ii) All pipe penetration shall be sealed with polymer modified mortar (PMM).iii) Saturate the surface with clean water before application of waterproof coating system. Once water get dried off apply one coat of High Performance & Ultra flexible polymer modified elastomeric waterproofing membrane system of Fosroc-Brushbond ultrafex or equivalent system over the concrete followed a reinforcement fibre mesh over the layer of membrane.iv) Apply two coats of High Performance & Ultra flexible polymer modified elastomeric waterproofing membrane system over the above mentioned initial layer after sufficient curing for each layer (Total consumption requirement for all 3 coats as per manufacturer's spec) |
| 12 | Cement plastering with CM 1:4,12 mm thick one coat floated hard and trowelled smooth at all levels,excluding cost of cement |
| 13 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 14 | Providing and laying with approved brand vitrified floor tiles of size 600x600 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in suitable colours laid on 20 mm thick cement mortar 1:4 (1 Cement: 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm with adequate joint spacing of 3mm followed by grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge, excluding cost of cement |
| 15 | Providing and fixing vitrified floor tiles with water absorption less than 0.08% and conforming to IS :15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades of any size as approved by Engineer-in-Charge for skirting (height 10cm) to walls over 12 mm thick bed of cement Mortar 1:3 (1cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm with adequate joint spacing of 3mm followed by grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge, excluding cost of cement |
| 16 | Providing and laying with approved brand rectified Glazed Ceramic floor tiles of size 600x600 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in suitable colours laid on 20 mm thick cement mortar 1:4 (1 Cement: 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm with adequate joint spacing of 3mm followed by grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge, excluding the cost of cement. |
| 17 | Providing and fixing first quality ceramic glazed wall tiles conforming to IS :15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades of any size as approved by Engineer-in-Charge for dadoing to walls cement based high polymer modified quick-set tile adhesive (Water based) conforming to IS: 15477, in average 6mm (3mm on tile & 3mm on existing surfaceand joining together) thickness of type 3 adhesive followed by grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge. |
| 18 | Supplying and fixing anodized Aluminium frame work of extruded sections and approved brand / manufacturer including mitering the joints, fixing the frame work with necessary screws, drilling holes in floors/walls, providing plugs for fixing screws, finishing the sides of packing between frame work and walls with plaster of Paris, cost of timber packing if necessary, Rubber lining for air tightness, providing corner cleats etc.complete as per standard practice for glazed Doors, Windows, Partitions, Ventilators etc.including hinges ,pivots, tower bolts, fixtures etc.complete (All Aluminum works including fittings measured in Kg) |
| 19 | Glazing the Aluminium frame work of windows with 3 mm or nearest thick plain glass panes and anodized Aluminium approved brand beadings, with EPDM / NEOPRINE weather seals, gaskets of EPDM or PVC etc and screws as per standard practice at all levels (Measurement for overall area of doors / windows / ventilators) |
| 20 | Supplying and fixing 600 x 450 mm or nearest size bevelled edge mirror of approved quality superior make \\" with hard board or plastic sheet on the rear and fixing the same in position with necessary plugs & SS screws etc complete |
| 21 | Providing and fixing 35mm thick or nearest size fully solid flush door shutter conforming to IS 2202 with both sides BWR ply finished with 1.0 mm thick decorative laminate of approved make and shade, with edge lipping and using 100 mm size 4 nos. SS hinges of approved quality with SS screws complete with all necessary hardware- Dorset / Godrej or equivalent mortice lock with key on either side, SS tower bolt 1 no., door closer all of approved make as directed by the Engineer-in-charge |
| 22 | Providing and fixing PVC door of syntex or equivalant make with shutter frame made of extruded plastic section having dimension of 60 x 24 mm or nearest, paneling with single panel hollow plastic section of 20 mm thick with average wall thickness of 1 mm and outer frame of door made of extruded plastic section of 48 x 40 mm or nearest including providing and fixing all required fittings such as stainless steel butt hinges, PVC tower bolts, PVC handles etc.complete as per manufacturers specifications. |
| 23 | Supplying and fixing at all levels one piece European Water Closet with slim soft closing seat cover and twin flush fittings Cattler of CERA or equivalent approved quality /brand of size 655 x 355x 730 mm with P/S trap with all required fittings 1 No. 15mm superior PVC connection heavy type ,15mm CP regulating angle cock with wall flange, cutting and making good the walls and floors including giving connection to sewer pipe with all necessary specials,etc. complete as per direction at site. |
| 24 | Supplying conveying and fitting 450 x 425 x 330 Wash Basin Cuddle Neo of CERA/ equivalent with a pair of special alloy bolts for fixing the basin on walls with 1No. 15 mm heavy type CP quarter turnpillar cock with aerator of approved make 1 No.heavy type 15 mm PVC connection with CP learning nut 1 No.and 1 No.15 mm CP regulating valve of superior make ,1 No. 15mm CP waste coupling, 32mm PVC waste pipe etc. including cutting and making good the walls etc. complete. |
| 25 | Supplying and fixing of high flow single lever concealed diverter with exposed part F1005721 and concealed part F4030101 from Ruby series of CERA / equivalent including cutting and making good the walls,etc. complete. |
| 26 | Supplying and fixing angle cock with wall flange F1005201 from Ruby series of CERA / equivalent |
| 27 | Supplying and fixing spout with wall flange F1005661 from Ruby series of CERA / equivalent. |
| 28 | Supplying and fixing overhead rain shower- stainless steel 150 x 150 mm with 230 mm long shower arm of CERA / equivalent. |
| 29 | Supply and fixing of SS304 towel rail 24\\" length F5015103CH from meridian series of CERA/ equivalent |
| 30 | Supply and fixing of SS304 soap dish F5015106CH from meridian series of CERA/ equivalent |
| 31 | Supply and fixing of SS304 paper holder with flap guard F5015110CH from meridian series of CERA/ equivalent |
| 32 | Supply and fixing of SS304 tumbler holder F5015107CH from meridian series of CERA/ equivalent. |
| 33 | Supplying and fixing Health faucet ABS body with 1 meter SS braided connection pipe and hook, F8030105AB of CERA/ equivalent |
| 34 | Supplying and fixing PVC floor trap (single or multy type) of approved brand 110 mm size with required provision of outlets and inlets as per manufacturers specifications, cutting and making good the walls and floors, etc. complete. |
| 35 | Supplying and fixing 125 mm (5 inch) Stainless steel floor gratings (two piece) to PVC trap as per instructions at site |
| 36 | Supplying and fixing PVC pipes conforming to IS 4985 class III, 6 kg/sq.cm pressure for lines with all required specials such as plain bends, single junctions, elbows, crosses, unions, shoes, door bends, double junctions, vent cowls, etc. with or without door including cutting masonry or concrete floors, sunshades, etc and making the holes good after finishing the work. wherever necessary and jointing pipes with approved quality resin cement and fixing pipes with MS fixing clamps screwed on to wooden plugs embedded in masonry wherever required and painting the clamps with two coats of enamel paint over one coat primer. This includes testing of joints complete at all levels. for waste water lines:110mm or nearest outer diameter |
| 37 | Supplying and fixing PVC pipes conforming to IS 4985 class III, 6 kg/sq.cm pressure for lines with all required specials such as plain bends, single junctions, elbows, crosses, unions, shoes, door bends, double junctions, vent cowls, etc. with or without door including cutting masonry or concrete floors, sunshades, etc and making the holes good after finishing the work. wherever necessary and jointing pipes with approved quality resin cement and fixing pipes with MS fixing clamps screwed on to wooden plugs embedded in masonry wherever required and painting the clamps with two coats of enamel paint over one coat primer. This includes testing of joints complete at all levels. for waste water lines 75mm or nearest outer dia. |
| 38 | Supplying and fixing PVC pipes conforming to IS 4985 class III, 6 kg/sq.cm pressure for lines with all required specials such as plain bends, single junctions, elbows, crosses, unions, shoes, door bends, double junctions, vent cowls, etc. with or without door including cutting masonry or concrete floors, sunshades, etc and making the holes good after finishing the work. wherever necessary and jointing pipes with approved quality resin cement and fixing pipes with MS fixing clamps screwed on to wooden plugs embedded in masonry wherever required and painting the clamps with two coats of enamel paint over one coat primer. This includes testing of joints complete at all levels. for waste water lines 50mm or nearest outer dia. |
| 39 | Supplying, laying and jointing with solvent cement, Rigid PVC pipes conforming to IS 4985 Class V (10 Kg/cm2 pressure rating) for water lines with all required concealed (brass embeded) PVC specials, such as Tees, bends, elbow, union, reducer etc. with clamps if any including necessary cutting and making good the walls, earth work if required etc.complete - 25 mm OD Pipe |
| 40 | Supplying and fixing 20 mm CPVC pipe for hot water connection including all required CPVC brass specials, such as Tees, bends, PN 16 threaded elbows, union, reducer etc. with clamps if any including necessary cutting and making good the walls,etc complete |
| 41 | Supplying to civil store 20 mm ID gun metal/ bronze/ brass non return valve (NRV) of approved make and fixing the same to waterlines |
| 42 | Painting with synthetic enamel paint for each succeeding coat for woodwork/ ironwork including cost of all materials and labour. Please Enable Macros to View BoQ information |
