|
| 1 | Demolition brick work or stone/ boulder masonery built in cement mortar including all quoins , pillars etc Complete all as specified and directed. |
| 2 | M&L for brick work using sub class ‘B’ old size bricks, straight or curved on plan exceeding 6m mean radius, built in CM (1:6) Complete all as specified and directed. |
| 3 | M&L for old size brickwork with subclass `B' bricks, straight or curved on plan exc 6m mean radius, built in CM 1:6 except bricks Complete all as specified and directed. |
| 4 | Taking down cement plaster of any description on brick or stone walls, etc. including racking out joints, hacking for key, scrubbing down with water etc.&removing rubbish to a disance not exc 250m Complete all as specified and directed. |
| 5 | M & L for 15 mm thick rendering in CM 1:4 on fair faces of brick or concrete surfaces finished even and smooth (without using extra cement) complete all as specified & directed. Note:- Water proofing compound shall be measured and paid seperately. |
| 6 | Supply only integral water proofing compound complete all as specified & directed. |
| 7 | M&L for applying Two coats of 100% Premium acrylic emulsion paint using roller, over 2mm thickness putty, having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces using roller for painting . Complete all as specified and directed. |
| 8 | M & L for 15 mm thick in cement mortar 1:6 on faces of brick work or concrete surfaces, surface finished even & smooth with using extra cement complete all as specified and directed. |
| 9 | M&L for preparation of newly plastered surfaces of wall and applying two coat of oil bound distemper using roller, over a coat of primer complete all as specified and directed |
| 10 | M&L for 2 mm thick applying a layer of JK/ Birla putty on wall surfaces including cornics etc for proper levelling of plaster complete all as specified and directed. |
| 11 | M&L for rendering 5 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:3 and finished even and smooth in ceiling without using extra cement complete all as specified & directed. |
| 12 | M&L for preparing newly plastered ceiling surfaces and applying two coats of oil bound distemper using roller, over a coat of primer complete all as specified and directed. |
| 13 | M&L preparation of Complete removal of existing treatment plastered old surface of wall, applying 2mm thick wall care putty and making the surface smooth Finishing walls and applying Acrylic Smooth exterior paint of required shade, using roller (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)using roller for painting complete all as specified and directed. |
| 14 | M&L for complete removal of existing treatment , plastered or un-plastered surfaces of walls and applying two coats of oil bound distemper white or tinted using roller, over a coat of primer complete all as specified and directed. |
| 15 | M&L for complete removal of existing treatment , plastered or un-plastered surfaces of walls and applying two coats of plastic emulsion paint white or tinted using roller, over a coat of primer complete all as specified and directed. |
| 16 | M&L for preparation of old decorated surfaces of plastered or un-plastered surfaces of ceiling and applying one coat of OBD complete all as specified and directed. |
| 17 | M&L High gloss melamine polishing on wood work (One or more Coat) over a under Coat of French Spirit polishing (two or more coat) new work including a coat of wood filler complete as per direction of Engineer-in-charge. |
| 18 | M &L for Washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster 1:4 (1 cement: 4 coarse sand ) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3 Kg of cement per square metre, top layer 15mm cement plaster 1:1/2:2 (1 cement: 1/2 coarse sand : 2 stone chipping 10mm nominal size) in panels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings over 15mm thick rendering CM 1:4 Complete all as specified and directed. |
| 19 | Taking down wooden chowkhat or frame area not exc 1.5 sqm each with shutter (without taking off shutter from frame) Complete all as specified and directed. |
| 20 | Taking down wooden chowkhat or frame area exc 1.5 sqm and not exc 4 Sqm each with shutter (without taking off shutter from frame) Complete all as specified and directed. |
| 21 | Taking down shutters ( per leaf ) of any description exc 1 Sqm but not exc 2 Sqm each complete all as specified and directed. |
| 22 | M&L for 1st class teak hardwood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed including holdfast as approved by GE complete all as specified and directed. |
| 23 | S&F 35 mm thick 1st class teak hardwood Plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers,heritage wood work shutter design pattern as approved by GE, supplied and fitted to chowkats complete all as specified & directed. |
| 24 | S&F 30 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides,heritage wood work shutter design pattern as approved by GE complete all as specified & directed. |
| 25 | S & F 30 mm thick 1st class teak hardwood Glazed and skeleton door shutters, open rebated and prepared to receive gauze without sash bars, edges of framing plain fitted with cut and mitred beads for securing wire mesh or glass, size of members of shutter as specified in SSR Pt-I Sec-8 clause 8.24(a) fitted to chowkats, complete as specified and directed. |
| 26 | M&L for 30 mm thick 1st class teak hard wood heritage wood work shutter designer pattern (panelled/ plain) design pattern as approved by GE) including fixing to frame complete all as specified and directed. |
| 27 | S&F 30 mm thick 1st class teak hardwood glazed and skelton window and ventilators shutters open rebated and prepaired to received glass gauge etc divided into square with sash bar edges of framing plain chamfered or rounded fitted with cut and mittered beads for sequring glass gauge etc , size of members of shutters as specified in MES SSR -I section 8 clause 8.24 (b) complete all as spcified and directed |
| 28 | Factory made single extruded WPC (wood polymer Composite) solid door/ window/ Ceosetory window & other Frames/ Chowkhat of size 45 x 70 mm comprising of PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wwod powder/ rick husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms ) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded stat headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N / mm 2 and resistance to spread of flame of Class A catogory with property of being termite/ borer proof, water / moisture proof and fire retardant and fixed in position with MS hold fast/lugs / SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately).Complete all as specified and directed. |
| 29 | Factory made single extruded WPC (wood polymer Composite) solid plain flush door shutter of 35 mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/ cum and screw withdrwal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N mm2 modulus of elasticity 850 N / mm2 and resistance to spread of flame of Class A catogary with property of being termite/ borer proof, water/ moisture proof and fire retardanat and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS screws, all as per direction of Engineer-In-Charge (Note:- stainless steel butt hinges and necessary SS screws shall be paid separately. Complete all as specified and directed. |
| 30 | S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C' channel heaving a PVC sheet strip of 20mm width suck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing complete all as specified and directed. |
| 31 | S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm wood grain printed PVC sheet reinforced with M.S Square tube complete all as specified and directed. |
| 32 | M & L for Anodised aluminium Powder Coating (minimum thickness of powder coating 50 micron) frame for doors,windows, ventilators with one or more rebates including joining cleat for fixing etc. cComplete all as specified and directed. |
| 33 | M & L for Anodised aluminium Powder Coated (of Approved colour ,Thickness or powder coating not less than 50 micron) door Shutter , side hung type without sash bars, aluminium sections weighing 0.55 kg/m including frame of chowkhats, necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium Complete fittings and 5mm glass as required complete all as specified and directed. |
| 34 | M & L for Anodised aluminium Powder Coating of Approved colour (Thickness or powder coating not less than 50 micron) sliding window and ventilator shutters, sliding type(Three track) without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium and Sliding Arrangement, including 4mm glass Complete fittings as required complete all as specified. |
| 35 | S&F stainless steel sliding bolt 300mm long bolt type with bright bolt not less than 12 mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate all as specified & directed |
| 36 | S&F stainless steel heavy weight butt hinges 100mm in size complete all as specified and directed. |
| 37 | S & F for 125mm Extruded brass handles,fabricated type polished . Complete all as specified and directed. |
| 38 | S&F 150mm size Extruded brass handles, fabricated type polished . complete all as specified & directed. |
| 39 | S&F Brass barrel tower bolt 200 mm, extruded section. Complete all as specified and directed. |
| 40 | S&F Brass sliding bolt 300 mm long bolt type with bright bolt not less than 12 mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate all as specified & directed |
| 41 | S&F 100 mm butt hinges, medium weight Brass Complete all as specified and directed. |
| 42 | S&F Brass barrel tower bolt 150 mm, extruded section. Complete all as specified and directed. |
| 43 | S & F butt hinges, medium weight, Mild steel and fixed, size of hinges 100mm complete all as specified and directed. |
| 44 | Supply and fix 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast Aluminium alloy complete all as specified and directed. |
| 45 | S & F 150 mm long Extruded Aluminium alloy handles, fabricated type, anodised complete all as specified and directed. |
| 46 | S & F 150 mm long Aluminium, anodised, barrel tower bolts of extruded section Complete all as specified and directed. |
| 47 | S & F 30 mm flaps Continuous (piano) hinges, mild steel, bright finish or electrogalvanised Complete all as specified and directed. |
| 48 | M & L for painting to new wood and wood based surfaces of any description, over 10 cm in width or girth, not otherwise described with two coats of synthetic enamel paint over a coat of pink primer including preparation of surfaces. Complete all as specified and directed. |
| 49 | Dismantaling asbestos cement sheets(corrugated, semicorrugatd) in roof coverings complete all as specified and directed. |
| 50 | S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strenth of 550 Mpa as in roof covering / clading to waall , fixed self tapping screws complete all as specified and directed. |
| 51 | S&F Pre-painted galvatume aluminium zinc coating GI based Plain steel sheet 0.50mm thick of an colour having tensile strenth of 550 Mpa as in roof covering / clading to waall , fixed self tapping screws complete all as specified and directed. |
| 52 | Dismantling mild steel or wrought iron work in roof trusses,gratings etc and similar work complete all as directed |
| 53 | M&l for Dismatling timber scantling 40 sqcm and above in any position ,unframed work complete all as specified and directed |
| 54 | M&L for mild steel work in roof trusses,purlins,rafters,wind ties,crane gantries,posts,rails and fastenings and heavy bracket framing (Beam,Tee,Angle,Channel or Flat sections) including distance pieces,cleats etc complete all as specified and directed. |
| 55 | M&L for Framed work such as grills, angle grating etc. with ends of bars shouldered and or riveted or forged into spikes, framed guard bars, railings and similar work confirming to Fe-410-O or Fe-310-O, Complete all as specified and directed. |
| 56 | M&L for preparation of new steel and iron surfaces of any description, over 10 Cm in width or girth, not otherwise described and painting with two coats of synthetic enamel paint over a coat of red oxide premier complete all as specified and directed. |
| 57 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as directed. |
| 58 | M&L for ultra charged vitrified tiles 12-15mm thick (or thickness as specified by manufacture), (square/ rectangular) polished, area of each tiles exceeding 0.64 Sqm but not exceeding 1.20 Sqm (as approved by GE) in flooring set and jointed in premium epoxy grout (Kajaria KE-100 or equivalent) to match the colour of tiles and including bedding of average thickness 6mm thick premium tile adhesive kajaria CX-1 or equivalent for laying of tiles on brick/concrete surface, over screed bed of CM(1:4) 10mm thick complete all as specified and directed. (Note: Rates Inclusive of Premium epoxy grout, premium tile adhesive and shall not be paid separately).Complete all as specified and directed. |
| 59 | All as per item above but as in skirting complete all as specified and directed. |
| 60 | S&F Vitrified Ceramic tiles light shade 8 to 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.18 Sqm but not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement over 15mm screed bed in CM 1:6 complete all as specified and directed. |
| 61 | S&F Vitrified Ceramic tiles light shade 8 to 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.18 Sqm but not exceeding 0.36 sqm, in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement over 10mm thick rendering in CM 1:4 complete all as specified and directed. |
| 62 | M & L for non skid ceramic coloured /printed tiles 7 to 8 mm thick (square / Rectangular)area of each tiles exceeding 0.11 sqm but not exc 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match the tiles, laid over screed bed or bedding layer 15mm thick in cement mortar(1:6) for laying floor finishes Complete all as specified and directed. |
| 63 | M & L for glazed ceramic coloured / printed tiles 450mm x 300mmX7mm thick, on vertical surfaces set and jointed in neat cement slurry and pointed in white/coloured cement to match the tiles,over rendering 10 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 for backing of Dado/ Skirting & vertical Tiles complete all as specified and as directed. |
| 64 | M&L for Ceramic glazed wall tiles including designer/digital/HD/Polished tiles (thickness as specified by the manufacturer), area of each tiles exceeding 0.18 Sqm but not exceeding 0.72 Sqm in flooring set and jointed in premium epoxy grout (Kajaria KE-100 or equivalent) to match the colour of tiles and including laying over cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness bedding on brick/concrete surfaces complete all as specified and directed. (Note: Rates Inclusive of Premium epoxy grout, premium tile adhesive and shall not be paid separately). Complete all as specified and directed. |
| 65 | M&L Treatment of soil under existing floors/walls using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement :2 coarse sand) to match the existing floors/wall complete all as specified. |
| 66 | Dismantling of stone slabs and tiles of any description or thickness in floors, aprons laid, bedded and pointed in mortar complete all as specified & directed. |
| 67 | M&L Marble work Green Marble 18 to 20mm thick (table rubbed and polished) in floor, steps, jambs, dados, pillars, window cills, cooking platforms and like in 10 mm thick cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade complete all as specified and directed. |
| 68 | M&L for Mirror polishing on existing marble work/Granite work/stone work as in floors where ever required to give high gloss finish complete. Complete all as specified and directed. |
| 69 | M&L for Granite 18 to 20mm thick (Black/Red Lakha) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in 10mm thick cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified & directed by Engr-in-charge. |
| 70 | Dismantling of wall and ceiling boards (fiber, pulp, insulation etc,) or insulation boards/slabs/blankets, any thickness including cover fillet complete all as specified and directed. |
| 71 | S & F for Aluminium anodised snap grid frame work for false ceiling comprising of following section for making partitions of 605 X 605 mm size fixed to walls with rawl plugs and screws and hang to roof with s 6 mm dia. G.I. (upto 1200mm length) adjusting levelfixed to roof slabs by means ofceilling cleats made out of G.I.flat 40 x 3 mm size 60mm long and expansion hold fasteners12.5mm dia. 40mm long Complete all as specified and directed. size of main tee shall be :-(i)36.5mmx25mmx1.4mm thick, Weighing 0.24Kg/Rm(ii)Cross Tee 23.5mmx36.4mmx1.4mm thick Weighing 0.191 Kg/Rm and (iii)Wall angle 40mmx25mmx2mm thick. Weighing 0.36 Kg/Rm |
| 72 | S & F 4 mm thick non asbestos fiber designer ceiling (E-board classic) board / tiles for insulation and accoustic purpose, 600 X 600 mm size fixed in ceiling with and including dusting of surface complete all as specified and directed |
| 73 | M&L For Providing and fixing 10mm thick plaster of paris sunk or raised mouldingceiling (Gypsum anhydrous) to flat surface over 2nd class soft wood fillets, or metal frame work and reinforced with G.I. wire mesh (Fillets, metal frame work and G.I. wire mesh paid separately complete all as specified and directed. |
| 74 | S&F for Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surroundingwall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55mm thickness having kurledweb of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre tocentre. complete all as specified and directed by engr -in charge. |
| 75 | S&F for Providing & fixing false ceiling at all heights with GRG (Glass Fibre With Reinforced Gypsum) false ceiling tiles of perforated Size 595 x 595 mm of approved texture,with Semi perforated 12mm thick micro tegular edged GRG false ceiling tiles design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC0.50 to 0.75 as per IS 8225:1987, Noncombustible as per B 476 (part 4 )-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on interocking metal T-Grid of hot dipped galvanized iron section of 0.33mm thick (galvanized @120 grams per sqm including both sides) comprising of main T runners of size 15 x 32 mm of length 3000mm,cross-T of size 15x 32mm of length 1200mm and secondary intermediate cross-T of size 15 x 32 mm of length 600mm to form grid module of size 600x 600mm, suspended from ceiling using galvanized mild steel items (galvanizing @ 80 grams per sqm) i.e 50mm long, 8mm outer diameter M-6 dash fasteners, 6mm dia fully threaded hanger rod upto 1000mm length and L hape level adjuster of size 85x25x2mm. Galvanised iron perimeter wall angle of size 24x 24x0.40mm of length 3000 mm to be fixed on periphery wall I partition with the help of plastic rawl plugs at 450 tiles fully mm center to center and 40mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in Charge. |
| 76 | M&L, in repair, 18/19mm thick Soild WPC board, exterior grade, prelaminated one side with decorative choice laminations and other side balanceing white lamination, fixed piano SS hinges to WPC frame work in cup boards, rebated or flat edged fancy handle , Magnite lock complete all as specified and directed. |
| 77 | M&L for solid PVC wall lining consisting of 5.00mm thick single site prelam PVC sheet inclusive of insolvent cement and fixing at site on PVC frame complete all as specified and directed |
| 78 | S&F 5mm thick PVC sheet fillet of width 35mm for wall panelling inclusive of fixing on to wall to make PVC frame complete all as specified and directed |
| 79 | S&F in repair 5mm thick hollow PVC Sheet wall Panelling (sand wiched between the longitudinal grid in PVC Sheet) any pattern fixing at site with PVC beading/fillet complete all as specified and directed |
| 80 | M&L for fabrication and fixing BWP (Boiling water Proof) solid block Board 19 mm thick conforming to IS 1659- 2004 to be used ,inside depth not less than 0.50 metre. All the exposed surface which are or can be visible to be covered with 1.0 mm th. Sunmica of Approved colour, shade and finish. The surface which will come in contact with wall/ masonary/tiles etc shall be premiered with Appropriate Wood primer mixing Approved Antitermite chemical and pasting 250-micron water proof Plastic Sheet with appropriate adhesive. All the Pastings to be done with water resistant Adhesive. Any Butt joint should be strengthen with Screw and Fissures inserted with appropriate pasting compound. Shutters of storage unit to be formed out of 19 mm thick BWP ply and faced with 1.0 mm thick Sunmica. Provide shelf etc. made of 19 mm thick BWP B.B., polished to engineer-in-charge's approval. Complete Including with all necessary fittings like knobs, magnet catcher, running track for sliding, hinges any type, ball catchers, SS tower bolts 150mm , locks,SS handles 300mm long, adjustable shelves etc. as per directions of Engineer Incharge. Inside surfaces to be finished with 1.00 mm thick Sunmica and outer exposed surface with 1.00 mm th. Sunmica. Cupboard depth of 600- 750 mm. (Note: 1.Rates inclusive of solid block board, adhesives, fittings/fixtures, Sunmica and plastic sheet etc and shall not be paid separately. 2.Front facing area shall only be considered for payment ) including taking down old boarding any type. |
| 81 | Supply only a set of stainless steel baskets(304 grade) with fittings as in modular kitchen cabinet as per following details :- (i) Plate basket 21\\"x19\\"x8\\"-01 No. (ii) Plane basket 21\\"x19 \\"x 8\\" -01 No. (iii) Plane basket 17\\"x19\\"x8\\" -01 No. (iv) Butlery basket 17\\"x19\\"x4\\" -01 No. (v) Cup &Saucer basket 17\\"x 19\\" x4\\" -01 No. (vi) Single pull out 8\\" -01 No. (vii) GT -PT & Drip tray 22\\" -01 No. (viii) Stain less steel Telescopic channels of appropriate size -06 Nos. etc all as specified and as directed. Please Enable Macros to View BoQ information |
| 82 | Supply only a set of stainless steel baskets(304 grade) with fittings as in modular kitchen cabinet as per following details :- (i) Plate basket 21\\"x19\\"x8\\"-01 No. (ii) Plane basket 21\\"x19 \\"x 8\\" -01 No. (iii) Plane basket 17\\"x19\\"x8\\" -01 No. (iv) Butlery basket 17\\"x19\\"x4\\" -01 No. (v) Cup &Saucer basket 17\\"x 19\\" x4\\" -01 No. (vi) Single pull out 8\\" -01 No. (vii) GT -PT & Drip tray 22\\" -01 No. (viii) Stain less steel Telescopic channels of appropriate size -06 Nos. etc all as specified and as directed. Please Enable Macros to View BoQ information |
