|
| 1 | Earth work in excavation in foundation trenches in ordinary soil ( vide classification of soil item A) and disposal of excavated earth as obtained to a distance upto 50M including all lifts leveling ramming the foundation treanches, removing roots of trees, and shrubs all complete as per approved design, building specification and direction of E/I. + (Extra for earthwork in hard soil as per specification and direction of E/I. ( vide classification of soil item-B) |
| 2 | Providing coarse clean sand in filling in in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials labour, royalty and taxes all complete as per building specification and direction of E/I (Mode of measurement compacted volume) |
| 3 | Supplying and Laying (properly as per design and drawing) rip-rap with good quality of boulder duly packed including the cost of materials, royalty all taxes etc. but excluding the cost of carriage all complete job. |
| 4 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size) |
| 5 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:1½:3 (1 Cement: 1½ coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size) |
| 6 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level. 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size) |
| 7 | Providing Tor steel reinforcement of 8mm dia rods as per approved design and drawing exclusive carriage of M.S. bars to work site, cutting, bending and binding with annealed wire with cost of the wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I. TMT Fe 500 (only valid for SAIL & TATA STEEL) #8mm |
| 8 | #10mm |
| 9 | Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 10 | Labour for fabricating, erecting, hoistion and fixing in position structrral steel work in R.S. Joist, channel, Angle, Tee, flat, plate, latice member, built up compound section in column, girder, stair case, or truss including cost of gusset plates, holding down bolts, anchor plates at all heights and depths, bolting, welding ( machining wherever necessary) with applying a priming coat of red lead paint all complete as per approved drawing, building specification and direction of E/I. |
| 11 | Providing two coat of painting with ready mixed paint over steel surface with complete job |
| 12 | 12.50 Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-Charge) of total coated thickness 0.50mm (base metal of minimum 0.45mm thickness with total coating thickness of 0.05mm) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.12.1.1 1.00 mm thick with zinc coating not less than 275 gm/m² |
| 13 | Labour for fitting and fixing G.C.I. Or C.A. Sheet roofing in proper slope including the cost of \\"J\\" or \\"L\\" hooks, limpet and bitumen washers, carriage of sheet to work site, and taxes all complete as per building specification and direction of E/I. |
| 14 | Providing random rubble stone masonry in C.M. (1:4) in foundation and plinth with hammer dressed stone of less than 0.03 M3 in volume and clean coarse sand of F.M. 2 to 2.5 including cost of screening, raking out joints to 20mm depth, curing, taxes and royalty all complete as per building specification and direction of E/l. |
| 15 | Providing 25 mm thick cement plaster (1:4) with clean coarse sand of F.M. 1.5 ircluding screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l. |
| 16 | Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete |
| 17 | Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge. |
| 18 | Dismantling patent stone floor including …...do…. |
| 19 | Dismantling old plaster and pointing in cement or lime and raking out joints to 15 mm. depth,watering nad disposal of unserviceable materials with all leads all complete as per direction of E/I |
| 20 | Leak repair to terraced roof with cement and powder application,including cost of all labour and materials, dismantling old terrace where necessary,disposal of unserviceable materials all complete as per building specification and direction of E/I. |
| 21 | Providing two coats of snowcem of approved shade and make over old surface ..do… |
| 22 | Supplying, fitting and fixing M.S. grill gate with M.S. grill made of 20X6mm M.S. flats or 16mm M.S. square bars fitted on 25X25X6mm M.S. Angle frame of size 60X60X6mm. Including cost of fabrication, providing necessary locking arrangement with haskal and domny duly fixed in P.C.C. (1:2:4) blocks of required size applying a priming red lead paint over steel work, taxes all complete as per drawing specification and direction of E/I. |
| 23 | Providing primer one coat of red lead paint of approved make over new steel surface including preparing the surface after cleaning, removing dust, dirt, scales smokes and grease and cleaning the surface throughly including cost of scaffolding and taxes all complete as per building specification and direction of E/I. (Mode of measurement area shall be multiplied by the co-efficient as indicated in building specification) |
| 24 | Providing two coat of painting with ready mixed paint of approved shade and make over steel surface including cleaning the surface throughly , scaffolding and taxes all after removing dirt including scales smokes, grease and sand papering including cost of scaffolding and taxes all complete as per building specification and direction of E/I. |
| 25 | PWAY HYDT: of drilling 200x165x125mm meter deep bore well in all kind of soil and rock in rural area for installation of Pump set with hydraulic DTH Rig machine, all complete including supplying all materials , tool ,drilling rig, Air Compressor and equipment, as well as fuel, lubricants and cost of transporting of Rig machine and other vehicles up to the site from 0-50 |
| 26 | from 51-125 |
| 27 | Supplying submersible pump sets confirming to IS 8034 and motor confirming to IS 9283. Pump shall be suitable for various delivery head and discharge with stainless steel pump shaft and polypropylene/ noryl impeller. Motor suitable for working on 415V±10%, 3PH, 50 Hz, A.C. supply with cable guard, thrust carbon/ fiber bearing to withstand entire hydraulic thrust, water proof winding shall be provided. The pump set shall be suitable for direct coupling Pump shall have suitable outlet as per manufacturers design. Anti thrust stream lined non return valve shall be provided with pump: 3 meter submersible copper conductor cable in single/ double run shall be provided with each pump with rope for lowering Lumsum rate 16/m lumsum. Submersible pump set 100 mm dia (with polypropylene/Noryl Impeller) up to 20 stages 1.5 HP |
| 28 | Rope for lowering lumsum rate 16/m |
| 29 | FR PVC insulated 3 Core 4 sq.mm..copper wire (Add 14.95% on basic rate for C.P and OHC) |
| 30 | DOL starter with SS Enclosure with 380/415 Volt coil 5 to 10 H.P |
| 31 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply including all CPVC plain &.. Do all.. |
| 32 | Providing and fixing male ended 15 mm dia brass bib cock of approved |
| 33 | Providing and fixing brass/C.I stop cock of approved quality all |
| 34 | Polythene water storage tank of mark with cover and suitable locking system in double layer confirming to IS :12701:1996 with latest revision |
| 35 | Supply of 200 mm dia x3.00 mm long upvc casing toIS 12818 :20216 (CML No. 5543459) latest revision including carriage (Basic Rate) |
| 36 | Providing and laying 25mm thick kotah stone slab flooring of approved size texure and colour over 19mm thick base of lime mortar (1:1:1) (limeputty:surkhi:coarse sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing to granolithic finish with approved quality of carborandum stone including cost of curing, taxes and royalty all complete as per building specification and direction of E/I. -(iv) 600X600 mm size |
| 37 | Rail Pole 52 kgs13 meter |
| 38 | Filling in foundation trenches and plinth in layers not exceeding 150 mm thick well watered ,rammed,fully compacteed and fine dressed with earth obtained after cutting within a lead of 50 m and lift of 1.5 m all complete as per building specification and direction of E/I (mode of measurement compacted volume). |
| 39 | carriage of materials Sand |
| 40 | Stone Chips |
| 41 | Cement |
| 42 | Rubble stone |
| 43 | Steel |
| 44 | PSC Pole 200 KG W.L (8 mtr.) |
| 45 | LT XLPE Ab cable 3Cx120+1Cx16 mm2 |
| 46 | Suspension Clamp suitable for 95-150 sqmm Bare Messenger (Including 1 No. Suspension Clamp with bracket +1.5 Mtr SS strap +2 Nos, SS buckle ) |
| 47 | Dead End Clamp Suitable for 95-150 Sqmm Bare Messenger (Including 1 No. Dead End Bracket + 1 No. Dead End + 1.5 Mtr SS Strap 2 Nos. SS buckle) |
| 48 | Insulation piercing connector Type-1 (main 16-95 mm2 & tap 4-35 mm2 |
| 49 | Insulation piercing connector Type-li (main 16-95 mm2 & tap 16-95 sq mm) |
| 50 | Service main anchor clamp for proper support of service cable(4mm2 and 10 mm2) |
| 51 | Spring loaded distribution Bus Bar insulated Box for fixing on pole suitable for AB XLPE Cable and three phase connection 1 incoming and outgoing 3 phase connection as per field requirement |
| 52 | 11 KV Stay Set Complete (1800x16 mm) with stay wire 7/10 SWG |
| 53 | Angle/side Stay Clamp (50x6 mm) for 9 mtr 400kg PSC Pole GALVANIZED] |
| 54 | Sundries Charges including nut bolts, paint etc |
| 55 | Contingency charges |
| 56 | store charges |
| 57 | Transportation Cost |
| 58 | T&P Cost |
| 59 | Overhead Cost |
| 60 | Labour Cost(as per respective LCA sheet )(in INR) |
| 61 | Department supervision charge @15% on LC |
| 62 | GST on Supervision Charge @ 18% |
| 63 | Gst @ 18% on Lab Cost |
| 64 | Add GST on Civil Work |
| 65 | Add Labour Cess Please Enable Macros to View BoQ information |
