|
| 1 | Dismantling of asbestos cement sheet /Plain or corrugated steel sheeting, (corrugated or semi corrugated) in roof covering complete all as specified and as directed. |
| 2 | S&F Pre painted galvalume aluminium zinc coating galvanised based corrugated steel sheet of 0.50 mm thick of approved colour having tensile strength of 550 Mpa as roof covering/cladding to wall fixed with self tapping (SD) screws complete all as specified and as directed |
| 3 | S&F Ppre-painted galvalume aluminium zinc coating galvanised based plain steel sheet of 0.50 mm thick of approved colour having tensile strength of 550 Mpa as ridge, gutters fixed with self tapping (SD) screws complete all as specified and as directed |
| 4 | Dismantling timber Scantling unframed work in fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section complete all as specified and as directed. |
| 5 | Dismantling timber Scantling unframed work 40 sqcm and over in section, in any position and removing store complete all as specified and as directed. |
| 6 | S&F Wind ties for roof including securing bolts including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe 290 Gde E-165 etc complete all as specified and directed. |
| 7 | S&F Rolled mild steel sections of Fe 410-W (GDE E-250) Quality “A” frame work as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates complete all as specified and as directed. |
| 8 | Dismantling wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards / slabs / blankets any thickness including cover fillets or frame work complete all as specified and directed. |
| 9 | S & F E Grid suspended false ceiling grid system of size 600 x 600mm with main runner 39x29.7x0.60mm cross tee 29x24.7x0.60mm and wall angle 22.2x22.2x0.50mm ceiling suspended with 2 to 2.5 mm dia GI wire hanger fixed to purlin / truss etc complete (Main runner, cross tee, wall angle of MS galvanised with PPCGS) over the grid providing 4mm thick HPSC pre primed self designer texture non asbestos fibre cement building board fixed to frames etc complete all as specified and and as directed. |
| 10 | Demolition cement concrete (unreinforced) in ground floors and pavings n.exc 15cm thickness (below or above ground level) ncluding removal of rubbish/ demolished materials out of MD land complete all as specified and directed. |
| 11 | M&L 75 mm thick PCC (1:3:6) type C2 (using 40mm graded stone aggregate) as in plinth protection laid in alternative bays finished even and smooth without using extra cement including making 10 mm wide grooves to full depth at 3 m interval and at every change of direction and filling the grooves with mixture of bitumen and sand mixed in the ratio of 1:3 by weight and top 10 mm depth sealed with sealing compound grade ‘A’ complete all as complete all as specified and as directed |
| 12 | Demolition of brickwork or stone/boulder masonry, built in cement mortar with all quoins, arches, pillars, etc but excluding ashlar facings, dressed stone work and precast concrete articles ncluding removal of rubbish/ demolished materials out of MD land complete all as specified and directed. |
| 13 | M&L Brick work with fly ash bricks old size, straight or curved on plan exceeding 6.0 metre mean radius built inCM (1:6) complete all as specified and as directed. |
| 14 | M&L Brick work with fly ash bricks old size, straight or curved on plan exceeding 6.0 metre mean radius in half brick thick walls built in CM (1:4) complete all as specified and as directed |
| 15 | M&L Providing PCC (1:3:6), type C-1 (using 20mm graded stone aggregates) as in coping including necessary use and waste of formwork and finishing exposed concrete surfaces fair and even and weathering, slightly rounded or chamfered angles and throating complete all as specified and directed. |
| 16 | Demolition of RCC of any description and in any position not otherwise specifically provided rainforced (rainforcement of cut as required to facilasite demolition etc) including removal of rubbish/ demolished materials out of MD land complete all as specified and directed. |
| 17 | M&L Providing RCC (1:2:4) (nominal mix) type B1 (using 20 mm graded stone aggregate) as in RCC bands supported on walls, beams and columns in floors,roof, landings, balconies, canopies, deck slabs and in shelves and the like complete all as directed. |
| 18 | Use and waste of formwork to sides and soffits o floor or roof beams, beam haunhings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs,etc. also splays between floors and beams etc as in rough finished flat surfaces of concrete complete all as directed. |
| 19 | M&L TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips,complete all as specified and directed. |
| 20 | All as per Item No.19 above,but 5mm dia and over upto and including 10mm dia as in stirrups , spacers and binders etc |
| 21 | Taking down chowkats or frames with shutters (without taking off shutters from frames) of size exceeding 1.5 square metre but not exceeding 4 square metre each complete all as specified and as directed. |
| 22 | Taking down chowkats or frames with shutters (without taking off shutters from frames) of size not exceeding 1.5 square metre each complete all as specified and as directed. |
| 23 | S&F Steel windows (fly proof and glazed shutter) made with galvanised steel colour coated/ powder coated (Base steel as per IS 513 'D', galvanised as per IS 277 with zinc of 120gm/sqm) with total coating thickness of 0.60mm (outside for glazing and inside gauged shutter) Sections for frame should be of 72mmx55mm, section for mullian should be 72mm x 50mm section for shutter frame should be 47mmx 20mm and section for fixing glass bead should be 12mm x 12mm and section for fly mesh shutter frame should be 40mm x 20mm mesh fixing should be of 18mm x 0.6mm. Stainless steel wire mesh of 0.45mm dia and average width of aperture 1.4mm shall be used for fly proofing 4mm thick plain sheet glass to be used for glazing of glazed shutters complete all as specified and as directed. |
| 24 | S & F PVC solid ventilator frame size 55 X 47mm with wall thickness of 5mm made out of extruded 5mm PVC sheet, meter cut at two comers and jointed with 2 Nos of 150mm long brackets of 15 x 15mm MS square tube the two vatted profiles are to be reinforced with 19 x 19mm MS square tube the 50% of bottom portion is fixed with 4mm pin headed glass and balance 50% of top portion is fixed with 4mm thick pin headed glass lowers and cover with 0.36mm dia stainless steel wire mesh at top portion including necessary PVC beading with screws and 3 Nos 12mm dia MS guard, bars fixed in ventilator frame including two coats of synthetic enamel paint over a coat of red oxide primer to MS guard bars etc., complete all as specified and as directed.Make: SINTEX or equivalent in RAJSHRI/NANDI as approved by GE. |
| 25 | M&L PCC (1:2:4) type B1 (using 20 mm graded stone aggregate) as in coping, bed plates, filling back hollow portion of chowkats complete all as specified and as directed. |
| 26 | M&L Cutting holes in brick wall built in cement mortor for inserting hold fast and making good the disturbed portion in cement mortor 1:3 depth of embeded portion exc half brick & N.exc one brick complete all as specified and as directed. |
| 27 | S & F 40mm thck Flush shutters, solid coreconstruction, with block board core and plywood face panels, commercia type on both sides complete all as specified and as directed. |
| 28 | S & F 2nd class hard wood 30 mm thick factory made glazed and skelton shutters, open rebated and prepared to receive glass, gauge etc (without sash bars) edge of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc size of member of shutter as specified in SSR Part-I section 8 clause 8.24(a) etc completed all as specified and directed. |
| 29 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/Chowkhat of size 50 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/sqmm and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. |
| 30 | S & F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/sqmm, modulus of elasticity 850 N/sqmm and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. |
| 31 | S&F 150 mm extruded aluminium alloy hands, fabricated type, anodised complete all as specified and directed. |
| 32 | S&F 150mm aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and directed. |
| 33 | S&F 100 butt hinges extruded aluminium alloy with galvanised mild steel hinges complete all as specified and directed. |
| 34 | S&F Mild steel 300 mm ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed. |
| 35 | S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples etc complete all as specified and directed. |
| 36 | Taking down cement plaster of any description and thickness on brick walls including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed |
| 37 | M&L Rendering 12 mm thick CM (1:4) on fair faces of brick work or concrete surfaces without using extra cement complete all as specified and as directed. |
| 38 | M&L Rendering 15 mm thick in two coats, 10 mm thick in CM (1:6) and 5 mm thick in CM (1:4) mixed with integral water proofing compound as per manufacturers instructions, on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and as directed. Note: Water proofing compound shall be measured and paid separately. |
| 39 | Supply only integral water proofing compound. |
| 40 | M & L Preparing newly plasterd wall surfaces of walls and applying two coats of acrylic distemper over and including a coat of primer using chalk whiting etc complete all as specified and as directed. |
| 41 | M & L Preparing newly plasterd wall surfaces and applying three coats of white wash complete all as specified and as directed. |
| 42 | M&L Complete removal of existing treatment of old painted wall surfaces and applying two coats of acrylic distemper over and incuding a coat of alkali resistant primer over and including 3.00 mm thick white cement based wall care putty for smooth finish.etc of approved make & shade on walls and other places of up toany height complete all as specified and as directed. |
| 43 | M&L Preparation of new or previously untreated steel surfaces of any description, over 10 cm in width or girth, not otherwise described and apply two coats of synthetic enamel paint (ordinary tint) over and including a coat of primer with red oxide, zinc chrome complete all as specified and directed. |
| 44 | M&L Prepation of new or previously untreated wooden surfaces of any description, over 10 cm in width or girth not otherwise described applying two coat of synthetic enamel paint including one coat of pink primer etc complete all as specified and directed |
| 45 | M & L Preparing old decorative surfaces of walls, by washing, rubbing down, stopping and applying two coat of cement base paint of any colour all as apecified and as directed |
| 46 | Dismantling stone slabs and tiles of any description or thickness in floor, aprons laid bedded and pointed in any mortar complete all as specified and directed |
| 47 | Dismantling floor, hearth or wall tiling including cement mortar bedding removing serviceable tiles and rubbish off the premises etcand removal of rubbish/ demolished materials out of MD land complete all as specified and directed. |
| 48 | M&L Non-skid ceramic tiles (Coloured) 7 to 8mm thick rectangular area of each tiles exceeding 0.18 Sqm not exceeding 0.36 Sqm as in floors etc,.set and jointed in neat cement slurry and pointed in white or coloured cement to match, etc over and including 15 mm thick CM (1:6) screed bed complete all as specified and as directed. |
| 49 | M&L Non-skid ceramic tiles (Coloured) 7 to 8mm thick rectangular area of each tiles exc 0.18 sqm not exceeding 0.36 Sqm as in skirting / dado etc,.set and jointed in neat cement slurry and pointed in white or coloured cement to match etc.over and including 10 mm thick CM (1:4) backing coat complete all as specified and as directed |
| 50 | M&L Non skid coloured ceramic tiles of size exceeding .0.06 square metre but not exceeding 0.11 square metre of 7 to 8mm thick as in floors etc,.set and jointed in neat cement slurry and pointed in white or coloured cement to match, etc over and including 15 mm thick CM (1:6) screed bed complete all as specified and as directed. |
| 51 | M&L Glazed ceramic coloured wall tiles of approved colour of size 350x 250x 7/ 450x300x7 mm thick on vertical surfaces as in skirting / dado etc,.set and jointed in neat cement slurry and pointed in white or coloured cement to match etc.over and including 10 mm thick CM (1:4) backing coat complete all as specified and as directed |
| 52 | M&L18 mm thick granite tiles (of any size) machine cut, jointed with grey cement slurry, and pointed with white cement with admixture of pigment to match the shade of granite stone duly grinding and polishing laid over and including 15mm thick screed bed of 1:4 in steps, jambs, pillars, window cills, cooking platforms and like complete all as specified and as directed |
| 53 | Rounding of / moulding to edges (half round) of stone of any description including rubbing and polishing (Granite finish), complete all as specified. |
| 54 | Taking up or down steel tubing and connection, removing clear off site after credit for the same is recovered by the dept., bore of pipe 15mm complete all as specified and directed. |
| 55 | S&F CPVC pipes, SDR 11, 16 mm outer dia of pressure rating 6kgf/sqcm conforming to IS-15778 with all CPVC fittings with such as brass elbow ,Tee, bends, unions ,sockets , male and femaleThreaded Adoptor and end pieces etc to receive fittings and fixed with solvents fixed to walls / ceiling with all clamps in Shafts/ducts with all necessary scaffolding to fix the pipes and testing the joints under prescribed pressure etc complete all as specified and as directed. |
| 56 | Taking up or down steel tubing and connection, removing clear off site after credit for the same is recovered by the dept., bore of pipe 20mm complete all as specified and directed. |
| 57 | S&F CPVC pipes, SDR 11, 20 mm outer dia of pressure rating 6kgf/sqcm conforming to IS-15778 with all CPVC fittings with such as brass elbow ,Tee, bends, unions ,sockets , male and femaleThreaded Adoptor and end pieces etc to receive fittings and fixed with solvents fixed to walls / ceiling with all clamps in Shafts/ducts with all necessary scaffolding to fix the pipes and testing the joints under prescribed pressure etc complete all as specified and as directed. |
| 58 | S&F in repairs CP bib tap 15mm bore fancy type with crutch or butterfly handle, screwed for iron pipe or for unions and fixed complete all as specified and directed. |
| 59 | S&F in repairs stop valve / angle cock fancy type cast copper alloy chromium plated with capstan head serewed down for 15 mm dia iron pipe complete all as specified and directed. |
| 60 | All as per Item No.59 above, but fancy type, chromium plated with long shank and cup (concealed type) |
| 61 | S&F in repairs chromium plated shower roses 125mm size with or without swivel joint including fixing to steel pipe or union etc.complete all as specified and directed. |
| 62 | S&F PVC connections, 15mm size with PTMT nuts of length 450mm complete all as specified and directed. |
| 63 | S&F in repairs Vitreous China Squatting pan, \\"Orissa\\" pattern, size 580 x 440 mm white with integral foot rests including connection to trap and to flushing pipe, anti-syphonage pipe etc., including trap set in and including lime concrete complete including making good to floor complete all as specified and directed. |
| 64 | S & F in repairs PVC 10 ltrs capacity symphonic action type low level flushing cistern including flush pipe, cantilever brackets incluiding taking down existing cistern etc complete fixed in repairs complete all as specified and directed. |
| 65 | S&F Vitreous china wash basin, white, flat back, size 580mm X 450mm including CI brackets, 32mm dia brass chromium plated waste fittings with long screwed shanks and fly nuts flanged end bedded in red lead cement and other end fixed with & including cutting for & pinning in end of brackets and 15mm bore pillar tap, cast copper alloy fancy type chromium plated, screwed down high pressure complete all as specified and as directed. |
| 66 | S&F Stainles steel sink , 1 mm thick sheet of steel grade AISI 304 for kitchen or laboratory, with plug, waste pipe, washers and wastes including bedding in cement morter to dwarf wall or including fixing CI cantilever bracket, connecting union to pipe etc., overall size 495 x 420 mm with bowl size 410 mm x 330 mm x 160 mm etc complete all as specified and directed. |
| 67 | S & F in repairs SS cutrain rod 20 mm dia of standard thickness with fixing brackets, stops, rollers etc complete all as specified and directed. |
| 68 | Dismantling / taking down PVC/ Cast iron soil /waste pipes 100 mm / 75mm bore including all fitting like bends etc complete all as specified and directed |
| 69 | S&F 75mm bore PVC (SWR) pipe single socketed(ISI Marked) any length with rubber ring joints , complete fittings etc fixed to wall fixed with MS clamps 8 mm dia with two nuts wall nails etc complete all as specifed and directed. |
| 70 | S & F 110 mm bore PVC (SWR) Soil, waste and vent pipes single socketed in any length with rubber ring joints laid in floors or trenches complete all as specifed and directed. |
| 71 | S&F PVC (SWR) Nahani /Floor trap, 75 mm dia of out let, plain with grating including jointing to waste pipe with solvent and cement concrete type B1 (1:2:4) & including removing old trap and fixing of stainless steel grating in ground shape etc complete all as specified and as directed. |
| 72 | S&F PVC (SWR) junction single (single T ) equal or unequal 110mm dia with access doors complete all as specifed and directed. |
| 73 | S&F 110mm dia vent cowl PVC (SWR) complete all as specifed and directed. |
| 74 | S & F 110mm bore PVC (SWR) plain bends, any radius complete all as specifed and directed. |
| 75 | M&L in repairs HDF board, 25 mm thick exterior grade, pre-laminated both side decorative face lamination fixed with screws ,brackets to timber frame work with and including 1st class hard wood, 6 mm thick all around edging, complete all as specified and directed. |
| 76 | M&L in repairs MDF board, 18/19 mm thick exterior grade, pre-laminated both side decorative face lamination fixed with screws ,brackets to timber frame work with and including 1st class hard wood, 6 mm thick all around edging, complete all as specified and directed. |
| 77 | S&F Continuous (piano) hinges,mild steel, bright finish or electrogalvanised 40mm width of flap fixed with screws as in repairs complete all as specifed and directed. |
| 78 | S&F 50 mm size Butt hinges extruded aluminium alloy with galvanised mild steel hinge pin, anodised, type E-22 complete all as specified and as directed |
| 79 | S&F Stainless steel plate rack, wall mounted of size 750mm X 900mm X 200 mm of approved quality made of 1.00mm thick stainless steel for kitchen with necessary fixing material complete all as specified and directed. |
| 80 | S & F in repairs Towel rail 600mm long of brass chromium plated fixed with and including CP brass screws and wooden/plastic cleats. (Minimum weight 190 gms) complete all as specifed and directed. |
| 81 | S & F repairs 600mmx 450mm bevelled edge miirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specifed and directed. |
| 82 | S & F Rotational moulded polyethylene water storage tank 3 layer white colour water tank , non- toxic effect, algea formation protection (made from Virgin grade of polyethylene material which is duly stabilized with anti-oxident Plastic) of capacity 500 litres, (cylindrical vertical one piece moulded with closed top), the internal and external surfaces of tanks are smooth, clean and free from any hidden internal defects, hoisted and fixed in position including S & F necessary CPVC/GI fittings, inlet/outlet washout, overflow pieces long nipples, checknuts & washer, 20 mm dia ball valves high pressure of PTMT with epoxy coated Aluminum rod & high-density plastic ball (Minimum weight 210gms) and 20 mm bore PTMT/Brass stop cock, high pressure with crutch or butterfly handle etc complete including dismantling existing water tank complete all as specified and directed.Make: Cat Part No: HSWS-0050-02- Pure of M/S Sintex |
| 83 | M&L Mild steel framed work as in doors and chowkats or gates, ladder etc of angle or other section with gusset plates, rails, braces, MS sheet etc, complete, drilled for fixing of steel sheeting are other covering. Doors etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging fittings and conforming to Fe 410-W (Gde E-250) quality ‘A’ complete all as specified and as directed |
| 84 | S&F Mild steel sheeting of 1.25 mm thick plain, black sheet as in wall cladding, covering to door shutter and similar works cut to size, holes punched, including round headed screws fixed to steel framing with plan 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles etc as required complete all as specified and as directed |
| 85 | Taking down existing unserviceable point wiring of any description/type/ size of light/fan/tube/power/two way/bell etc on TW batten/conduit including removal of batten / conduit / gutties / wooden boards / switches / sockets / regulators/ light fittings etc and removal of unserviceable material out of site and making good the disturbed surfaces of wall/ceiling so as to match with the existing finishes complete all as specifed and directed. |
| 86 | Taking down old unservicieble existing submain wiring of any size and type complete all as specifed and directed. |
| 87 | Taking down old unservicieble existing DB's any size and type complete all as specifed and directed. |
| 88 | M&L Providing conceled point wiring complete with stranded copper conductor cables in non-metallic PVC conduit 1.5 Sqmm (nominal area) PVC insulated unsheathed cable up to 1100 V grade FRLSH conforming to IS - 694 multistranded drawn including conduit with new sunk type pressed steel terminal boxes suitable for MODULAR switches including fixing/grouting sunken/ surface as per site requirement covered with suitable modular white cover plate for suitable size for mounting of MODULAR switches, regulators and drawing continuous earth wire with one run of 1.5 Sqmm (nominal area) PVC insulated unsheathed cable up to 1100 V grade FRLSH conforming to IS - 694 multistranded copper conductor as earth wire and connecting to common earth dolly for one light/fan point controlled by one, one way switch 5 amps, SP and making good the disturbed wall surfaces to match with the existing surfaces complete all as specified and as directed. Note: 1. Modular cover plate with frame and modular metal flux box in the rate quoted. |
| 89 | All as per Item No.88 above,but one light point controlled by one, two way switch 5 amps, SP |
| 90 | All as per Item No.88 above,but one Bell point controlled by one, one bell push |
| 91 | All as per Item No.88 above,but one 3 pin 5 Amps switch socket outlet point controlled by one switch on independent board . |
| 92 | All as per Item No.88 above,but one 3 point 5 Amps switch socket outlet point controlled by one switch on the same board. |
| 93 | All as per Item No.88 above,but using 4.0 Sqmm single core FRLSH copper conductor cable of multistranded PVC insulated unsheathed 1100 Volts grade for 3 Pin 15 Amps switch socket combination point on independent board/AC Point including running of 4.0 Sq mm FRLSH copper conductor PVC insulated cable as earth continuity conductor. |
| 94 | S&F MODULAR switch 1 way 6 A, 1 Module capacity 230 volts complete all as specified and as directed. |
| 95 | S&F MODULAR switch 2 way 6 A, 1 Module capacity 230 volts complete all as specified and as directed. |
| 96 | S&F MODULAR switch 1 way 10 A, 1 Module capacity 230 volts complete all as specified and as directed. |
| 97 | S&F MODULAR socket 5 pin 6 amps 2 MODULE, 230 Volts complete all as specified and directed. |
| 98 | S&F MODULAR socket 6 pin 6/16 amps 2 MODULE, 230 Volts complete all as specified and as directed. |
| 99 | S&F Switch MODULAR 1 WAY 16 amps, 230 Volts complete all as specified and as directed. |
| 100 | S&F 2 MODULE regulator for compatibility with existing ceiling fans MODULAR 5 stepped type complete all as specified and as directed. |
| 101 | S&F Modular bell push of 6 Amps SP, 230 volts AC complete all as specified and directed. |
| 102 | S & F ding dong Bell AC,230 Volts,single pole complete all as specified and directed. |
| 103 | S&F Wall mounted LED batten with extruded aluminium heat sink provided for efficient heat dissipation & integrated electronic driver 1 x 20w, 230 volts, bipin holders, DIFFUSED TYPE connector block internally prewired etc with 2 Nos PVC round blocks for mounting arrangements including all accessories with new 3 core multi stranded copper conductor of size 23/0.193 from ceiling rose to fitting and including LED Tube 20W complete all as specified and as directed. |
| 104 | S&F LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete |
| 105 | S&F LED Light fitting 1x35 Watt complete with Bracket made out GI pipe med grade 25mm of L Shape 1.5 Mtr long incl clamps and nuts botls etc , all as specified and as directed. |
| 106 | S & F Ceiling rose three terminal surface bakelite type AC 50 Hz 230 volts of size 65 x 50 mm complete all as specified and directed. |
| 107 | S & F Sheet metal enclosure MCB DB SPN 12 way with 200 amps rated bus bar 240 volts double door with magnetic locking system complete all as specified and directed. |
| 108 | S & F MCB SP 6 to 32 Amps 240 volts for fixing on MCB DB's complete all as specified and directed. |
| 109 | S & F MCB SP 40 Amps 240 volts for fixing on MCB DB's complete all as specified and directed. |
| 110 | S & F MCB SPN 32-40 Amps 240 volts for fixing on MCB DB's complete all as specified and directed. |
| 111 | S&F Sheet metal enclosure vertical type MCCB DB TPN 4 way double door with suitable rated bus bar 415 volts suitable for and including MCCB TPN as incomer with suitable rated copper bus bar with neutral link including provision for 100 Amps MCCB 25KA TPN as incomer and SP/TP MCBs as outgoing and total number of modules equal to MCCB TPN + 12 with blanking plates and fixed flush to wall and making good the disturbed surfaces etc, complete all ass specified and as directed. Note: MCB SP/TPN will be measured and paid seperately. |
| 112 | S & F in repair MCCB 100A 16KA complete all as specified and as directed |
| 113 | M&L Earthing with galvanized mild steel earth plate electrode 60 centimetre x 60 centimetre x 6 mm thick buried directly in ground vertically to a depth not less than 2.25 metres below ground level, the top edge of the earth plate at a depth of not less than 1.5 metres below ground level connected to galvanized iron earth wire of 4 mm dia by means of bolts, nuts and washers made out of GI / steel earth wire protected by GI light grade pipe 15 mm bore, 20mm dia light grade galvanised iron pipe with funnel wire mesh for watering and connecting to main switch board / control board all s shown in electrical plate of SSR Pt - I connected to earthing test point and including testing on completion complete all as specified and as directed.NOTE: The unit rate shall also include for excavation, earth work in hard/dense soil, plain cement concrete 1:3:6 type C1 by using 20 mm graded aggregate in pit, 50 mm thick reinforced cement concrete 1:2:4 type B1 using 20 mm graded aggregate cover duly reinforced with 8 mm dia TMT bars @ 100mm centre to centre both ways, galvanised iron funnel with watering pipe, wire mesh, complete. |
| 114 | S&F Exhaust fan made of sturdy engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250mm including making hole of suitable size complete all as specified and directed |
| 115 | S&F Exhaust fan, steel body AC single Phase. 230V of size 300m complete with blades, and frame and louvers shutter,Copper winding including making hole of suitable size complete all as specified and directed |
| 116 | M&L Concealed sub main wiring with two runs of single core FRLSH PVC multistranded stranded unsheathed copper conductor cable of size 4 square mm and drawing through PVC conduit of 25mm dia with accessories on surface in wall/roof along with one run of 4 square mm FRLSH PVC insulated unsheathed multi stranded 1100 volts grade with copper conductor cable as earth continuity conductor connected to earth and earth dolly, connecting to main board including removing the existing wiring and making good the disturbed wall surfaces to match with the surroundings complete all as specified and directed.Note: 3 runs of 4 Sqmm FRLSH cable and 1 run of PVC conduit with accessories shall be measured as 1 unit of running metre. |
| 117 | Taking down and re-fixing of ceiling fans 1200/1400mm sweep and exhaust fan 230/300 mm sweep, remaining/cleaning of dust properly cleaning, greasing& overhuaB131:B143ling of bearings including refixing and connecting up all as directed by Engr-in-Charge. Note : Replacement of defective/worn out parts will be measured & paid for separately |
| 118 | S & F in repair capacitor 2/2.5 mfd as directed (Make - Asian/Usha/Epcos of siemens) complete all as specified and directed. |
| 119 | S & F in repair ball bearing of exsiting ceiling fans complete all as specified and directed. |
| 120 | S & F in repair twisted three core copper flexible cable of size 1.5 sqmm from connector to the ceiling rose complete all as directed |
| 121 | S & F in repair ‘U’ clamps complete with nut, bolts & split pins Heavy duty, suitable for existing ceiling fan complete all as specified and directed. |
| 122 | S & F in repair M.S. rod for ceiling fans 3 ft long with ‘U’ clamp at one end other end with out nut bolts washers or screwed thread with check nuts & pin complete all as specified and directed. |
| 123 | S & F in repair Nut of bolts washers for fan blades fixing of ceiling fan of any make/size/type as per site requirement ( 6 Nos for each set) complete,asuitable for existing ceiling fan on site complete all as specified and directed. |
| 124 | M & L Rewinding of stator complete with super enameled copper wire of gauge/ weight of copper coil, quick varnishing oiling, greasing insulating materials including replacement of worn out parts like u/s cotter pin, nut, screw, check nuts and bolts as required including cleaning of body and testing of the size 1200/1400mm sweep ceiling fans and 230/300mm exhaust fans of any make/model complete all as specifed and directed.Note :- Sapre parts except mentioned above and rewinding to be replaced will be measured and paid seprately under respective items of schedule. |
| 125 | S&F Geyser 25 Ltr capacity vertical type , ISI marked, metalic body, 2000 Watt, heating element with brass connector of series for both outlet and inlet, including installation and testing ofcomplete with suitable arrangement of fixing with suitable stud/Anchor fastner including PCC work with drilling holes complete all as specified and directed. Make- Havells/Bajaj/Crompton Greaves. |
| 126 | S&F PVC water connection pipe 15mm size with PTMT nuts of length 450mm for inlet and outlet connection (cold & hot water) compete all as specified and directed. |
| 127 | S&F 15mm bore GI water tubing (medium grade) with all fittings fixed in walls/floor complete all as specified and directed. |
| 128 | S&F 15 mm dia Stop cock brass with chromium plated for iron pipe ISI marked with screw end and fancy type complete all as specified and directed. |
| 129 | S&F 15 mm dia Bib tap cast copper alloy with crutch or butterfly handle, screwed down , screwed with chromium plated for iron pipe and fixed fancy type, ISI marked complete all as specified and directed. |
| 130 | M&L Cutting & screwing extg steel tubing of size 15 mm dia for alterations or additions or lengthening screw on pipe to form connector and done in position without taking down all as specified and directed. Please Enable Macros to View BoQ information |
