|
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator) means over areas (exceeding 30 cm in depth, nexc 1.5m deep,1.5 m in width as well as 10 Sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5m and getting out in any kind of soil as directed by Engineer-incharge. |
| 2 | Excavation in post holes, each hole not exc 0.50cum, getting out in hard/dense soil including returning filling, watering, well ramming earth sand removing surplus soil to a distance not exc 50 m, depositing where directed at a level not exc 1.5m from the starting point complete all as specified and as directed |
| 3 | M & L Providing PCC (1:4:8) type D2 (using 40mm graded stone aggregates) as in foundations filling and mass concrete complete all as specified and as directed |
| 4 | M & L Providing PCC (1:3:6) type C2 (using 40mm graded stone aggregates) as in foundations filling and mass concrete complete all as specified and as directed. |
| 5 | Use and waste of Formwork to sides of concrete foundations in rough finished, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and as directed. |
| 6 | M&L TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips,complete all as specified and directed. |
| 7 | M & L Providing RCC M25 (Design mix) (using 20 mm graded stone aggregates) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and as directed. |
| 8 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and as directed. |
| 9 | Removing excavated material exc. 500m & n.exc 1500m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and as directed. |
| 10 | M & L Brick work with fly ash bricks straight or curved on plan exceeding 6 metre mean radius with old size bricks built in CM (1:6) complete all as specified and as directed. |
| 11 | M & L Rendering 15mm thick in CM (1:6) on brick masonry or concrete surfacs finished even and smooth without using extra cement complete all as specified and directed. |
| 12 | M & L PCC (1:3:6) type C-1 (using 20mm graded stone aggregates) as in coping including necessary use and waste of formwork and finishing exposed concrete surfaces fair and even and weathering, slightly rounded or chamfered angles and throating complete all as specified and directed. |
| 13 | M & L Preparartion of new wall surfaces & applying two coats of cement based paint over a coat of primer complete all as specified and directed. |
| 14 | S & F Mild steel angle iron work as in struts and posts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc, flat iron fillets (for securing wire mesh and wire any type) including all necessary drilling, bolting or riveting and embedding in concrete and screwing etc, and similar work conforming to Fe-290 Gde E-165 complete all as specified and as directed |
| 15 | S & F Rolled hollow sections Fe-410- W(Gde-E-250) quality-A etc as in stanctions/ vertical column fixed with base plates or other connecting plates etc complete all as specified and as directed. |
| 16 | S & F Rolled hollow sections, I sections, angle, channel Fe-410- W(Gde-E-250) quality-A, etc as in main and cross beams, hip and jack rafters, purlins, tie runners bent to required shape where connected to common rafters fixed with angle cleats or other connecting plates etc complete all as specified and as directed. |
| 17 | S & F Steel work in tubular trusses including special shaped washer etc., complete using ERW or induction butt welded tubes conforming to I.S.11611979 garde St-240 complete all as specified and as directed. |
| 18 | S & F MS plate 8 mm to 12 mm thick plain Fe-410- W(Gde-E-250) quality-A, cut to shape forming holes and welded to truss and verticle post as base plate all as required complete all as specified and directed.. |
| 19 | S & F Mild steel screw bolts (machine made), diameter of shank 16 to 20 mm, with hexagonal or square heads at one end and screwed the other, or screwed both ends, Each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exc 10 cm and n exc 15 cm long all as specified and directed. |
| 20 | Supply only chain link MS galvanished fencing, any size or type complete all as specified and as directed |
| 21 | Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc including provision of binding wire complete all as specified and as directed |
| 22 | M & L 10mm dia Mild steel round bars of Gd. I IS 432 (Part I) Part-I cut to length, bent to shape required, including cranking, bending, hooking ends and binding with MS wire (annealed) not less than 0.90mm dia or securing with clips as in supporting of chain link fencing in any direction complete all as specified and as directed |
| 23 | S & F Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, Each screwed end to be fitted with washers and one hexagonal or square nut not exc 5cm long and diameter of neck is 12mm complete all as specified and as directed |
| 24 | S & F 4mm dia plain mild steel wire galvanised class 3 in fencing including straining and fixing to steel posts including securing with and provision of galvanised iron staples or steel pins etc as directed. (Each line of wire to be measured) complete all as specified and as directed |
| 25 | M & L Preparing new steel surfaces of any description exc 10cm width or grith and applying two coat of synthetic enamel paint over a coat of aluminium red oxide primer complete all as specified and directed. |
| 26 | M & L for preparation of new steel surfaces n exceeding 10cm girth or width and applying two coats of synthetic enamel paints over a coat of primer, complete all as specified and as directed |
| 27 | S & F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall bent to required shape, fixed with self tapping screws complete all as specified and directed. |
| 28 | S & F 1.00 mm thick Plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 complete all as specified and directed |
| 29 | S & F 2mm thick fibre glass reinforced translucent corrugated sheeting with two corrugations side lap fixed with coach screw and washer in roof, wall etc fixed with L-type or J-type or cranked hook bolts complete all as specified and as directed. |
| 30 | S & F 110mm dia PVC (SWR) grade single socketed pipes in any length complete with rubber ring joints fixed to walls complete all as specified and directed |
| 31 | S & F PVC (SWR) bends any radius of 110mm bore complete all as specified and as directed. |
| 32 | S & F LED Acrylic 3-d letters of English alphabets, numbers and symbols of approved size, font, case with provosion of electric supply along with supporting board of same material if required as a logo or an illuminating display board as in wall cladding including all other necessary fittings/accessories all as specified and directed |
| 33 | M&L Provision of 6.0 Mtr wide steel gate and 2.0 Mtr wide wicket gate including earth work excavation in any type of soil, return filling,removal of excess soil, PCC foundation, RCC columns by using M-25 (Design mix) concrete steel reinforcement,15 mm thick rendering,2 coats of exterior emulsion paint over a coat of primer, steel members for the gates and two coats of synthetic enamel paint over a coat of red oxide primer,MS sheet welded to frame,hold fasts,wheel track,etc complete all as shown on drg CECZ TD No 555 Sheet No 3 & 4/14 dated 23 Feb 2004,as specified and directed by Eng-in-charge. Please Enable Macros to View BoQ information |
| 34 | M&L Provision of 6.0 Mtr wide steel gate and 2.0 Mtr wide wicket gate including earth work excavation in any type of soil, return filling,removal of excess soil, PCC foundation, RCC columns by using M-25 (Design mix) concrete steel reinforcement,15 mm thick rendering,2 coats of exterior emulsion paint over a coat of primer, steel members for the gates and two coats of synthetic enamel paint over a coat of red oxide primer,MS sheet welded to frame,hold fasts,wheel track,etc complete all as shown on drg CECZ TD No 555 Sheet No 3 & 4/14 dated 23 Feb 2004,as specified and directed by Eng-in-charge. Please Enable Macros to View BoQ information |
