Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | Civil BOQ |
| 2 | Providing and erecting two legged metal tubular scaffolding (cup lock type) of width 1200 to 1500mm largely free standing using H frames of tubular pipes of minimum 40mm diameter, with base plates fixed or adjustable with necessary clamps, coulders, brackets for projections, joint pins, pulleys and other accessories including steel angle or tubular pipe bracings at adequate intervals, access platforms of metal or timber planks of span not exceeding 1.5 metre centre to centre, horizontal & vertical tubes joint with cup & lock system with M.S. Tubes, M.S. tube challis, M.S. clamps and staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for execution of work including provision of rubber inserts to pipe ends at point of contact with structure to avoid damage, including ccess ladders with intermidiate platforms. the scaffolding to be suitably braced and anchored to to the building using support systems created temporarily at the opening in walls using vertical and horizontal adjustable props on the exterior side of building structure, upto 25 metre height, above ground level . |
| 3 | Fencing: Providing and erecting corrugated galvanised iron sheets of 0.63mm thick (24 B.W.G.) fencing and fixed 75 mm above Ground level on vertical M.S Angle of 40 x 40 x 6 mm size including excavating pits for foundation and embedded in C.C. block using PPC cement of 1:4:8 mix of size 450 x 450 x 670 mm. at 1.75 M.c/c with iron bar 16 mm dia as hold fast including welding link with angle frame at 30 cm c/c with nuts and bolts and horizontal M.S. Angles at top and bottom of 25 x 25 x 5 mm size and vertical M.S. flat 35 x 5 mm and 25 x 5 mm horizontal including cross support of 40 x 40 x 6 mm Angles both sides at every corner or bends embedded in concrete blocks of 1:4:8 of size 450 x 450 x 670 mm etc. complete. |
| 4 | Providing second class Burnt Brick masonry with conventional/ I.S. type bricks in cement mortar 1:6 in foundations and plinth of inner walls/ in plinth external walls including bailing out water manually , striking joints on unexposed faces, raking out joints on exposed faces and watering etc. Complete. |
| 5 | Providing second class Burnt Brick masonry with conventional/ I.S. type bricks in cement mortar 1:6 in plinth as backing in composite masonry including bailing out water manually, striking joints, raking out joints and watering etc. complete. |
| 6 | Providing second class Burnt Brick masonry with conventional/ I.S. type bricks in cement mortar 1:6 in superstructure including striking joints, raking out joints, watering and scaffolding etc. Complete. |
| 7 | Providing Autoclaved Aerated Concrete Block masonary of conforming to IS:2185 (Part 3) - 1984 in extra fine jointing mortar of fixoblock of UltraTech or equivalent in superstructure including striking joints, raking out joints and scaffolding etc. Complete. (The test shall be carried out conforming to IS:6441 (Part I) - 1972 |
| 8 | Providing Autoclaved Aerated Concrete Block masonary of conforming to IS:2185 (Part 3) - 1984 in extra fine jointing mortar of fixoblock of UltraTech or equivalent in Half brick thick wall including striking joints, raking out joints and scaffolding etc. Complete. (The test shall be carried out conforming to IS:6441 (Part I) - 1972) |
| 9 | Providing internal cement plaster 12mm thick in single coat in cement mortar 1:4 without neeru finish to concrete or brick surfaces, in all positions including scaffolding and curing etc. complete |
| 10 | Providing and applying gypsum plaster ( with Gypsum material ) with finishing with gypsum material in 10 to 13 millimeter thickness to previously plastered surface / or on newly brick surface ( Excluding rough cast plaster ) in all position including preparing and Finishing the surface scaffolding etc.complete. |
| 11 | Providing sand faced plaster externally in cement mortar using approved screened sand, in all positions including base coat of 15 mm thick in cement mortar 1:4 using waterproofing compound at 1Kilogramper cement bag curing the same for not less than 2 days and keeping the surface of the base coat rough to receive the sand faced treatment 6 to 8 mm thick in cement mortar 1:4 finishing the surface by taking out grains and curing for fourteen days scaffolding etc.complete. |
| 12 | Providing and fixing all sides natural stone 16-18mm thick as specified below of approved quality, pattern, colour and thickness for plinth/external surface from leading natural stone suppliers such as Siddhivinayak stones, CMC, RK marble including making the groove in existing cladding/ plaster/ concrete/ masonry, machine cutting, leveling, smooth cement plastering along the sides to match the existing surface in cement mortar, filling the joints with neat cement or pigment mixed with cement, cutting for utility pipe in the shape as directed, cleaning, finishing, curing etc complete as directed by Engineer In Charge. |
| 13 | Providing and laying machine cut machine Polished Kota stone flooring 25mm to 30mm thick and required width in plain/ diamond pattern on bed of 1:6 C. M. including cement float, filling joints with neat cement slurry, curing, polishing and cleaning etc. complete. Flooring and skirting/Cladding |
| 14 | Providing and laying machine cut machine polished machine cut Kota stone slabs 20 to 25 mm thick for treads and risers of steps and staircases, with rounded nosing for the treads on a bed of 1:4 cement mortar including cement float, filling joints with neat cement slurry, curing, polishing and cleaning etc. complete. Steps and Landing |
| 15 | Providing and laying in position flooring of telephone black / Amba White / Cat bary brown / Ruby red / Ocean Brown granite stone of approved shade and size 18 mm to 20 mm thick on bed 1:6 cement mortar including cement floats striking joints, pointing in C.M. 1:3 curing and cleaning etc. complete. Flooring and skirting |
| 16 | Providing and laying telephone black / Amba White / Cadburybrown / Ruby red / Ocean Brown granite stone of 18 to 20 mm thick for door frame/ dado/ window boxing etc. On C.M. 1:6 including filling joints with polymer base filler nosing/moulding the sharp edges wherever necessary, curing, etc. complete. |
| 17 | Providing and fixing machine cut machine polished 18 mm to 20 mm thick telephone black / Amba White / Cat bary brown / RBI red / Ocean Brown granite stone for treads and risers of steps and staircases of approved colour and shade with full moulding and three grooved line for the treads on bed of 1:4 Cement mortar including float filling joints with neat cement slurry curing polishing and cleaning etc. complete. |
| 18 | Providing and fixing 18 mm thk scratch proof Engineered wooden flooring and skirting in deep walnut finish / teak finish as per sample approved by the architect and company specifications. Item to include providing and fixing skirting matching to the flooring as per company details and design including necessary bedding etc. complete. |
| 19 | Providing and laying vitrified mirror / glossy finish tiles decorative type having size 590 mm to 605 mm x 590 mm to 605 mm of 8 to 10 mm thickness and confirming to IS. 15622-2006 ( group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and clearing etc. complete. |
| 20 | Providing and laying vitrified matt fininsh tiles having size 590 mm to 605 mm x to 605 mm of 8 to 10 mm thickness and confirming IS. 15622-2006 (Group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement morar including neat cement float, filling joints, curing and cleaning etc. complete. |
| 21 | Providing and laying vitrified mirror / glossy finish tiles having size 590 mm to 605 mm x 590 mm to 605 mm of 8 to 10 mm thickness and confirming to IS. 15622-2006 ( group Bla) of approved make, shade and pattern for dado and skirting in required position fixed in 1:4 cement mortar including neat cement float, filling joints, curing and clearing etc. complete |
| 22 | Providing and laying insitu polished Terrazo stone as per the Architectural drawings, 18 mm thick of an approved quality and size for flooring including cement mortar bedding of 25 mm thick in 1:4 proportion, cement float, machine cutting, dressing, leveling, jointing, filling the joints with neat cement slurry or with required pigment, machine polishing at site, curing, finishing, etc. complete as directed by Engineer In Charge. |
| 23 | Providing and laying insitu polished Terrazo stone as per the Architectural drawings, 25 mm thick of an approved quality and size for flooring including cement mortar bedding of 25 mm thick in 1:4 proportion, cement float, machine cutting, dressing, leveling, jointing, filling the joints with neat cement slurry or with required pigment, machine polishing at site, curing, finishing, etc. complete as directed by Engineer In Charge. |
| 24 | Providing and fixing in required position skirting or dado of polished Terrazo Stone slab 18 mm thick fixed on base on plaster of cement mortar 1:4 including cement float, filling joints with cement slurry, curing rubbing, polishing and cleaning complete. |
| 25 | Providing and laying insitu polished Terrazo stone as per the Architectural drawings (Machine cut) 18 mm thick of an approved quality and size for Tread and Riser including cement mortar bedding of 25 mm thick in 1:4 proportion, cement float, machine cutting, nosing, dressing, leveling, jointing, filling the joints with neat cement slurry or with required pigment, machine polishing at site, curing, finishing, etc. complete as directed by Engineer In Charge. |
| 26 | Providing and applying interior wall finish luster of approved make on internal wall surface as detailed below Scrapping the surface with emery paper and wipe clean wall primer with brush with mineral turpentine with brush 8 to 10% and oil 15 to 20% with roller and allowing to dry for a period 6 to 8 hours. wall putty with appropriate proportion of water allowing to dry for period 4 to 6 hours. Scrapping with Emery paper 180 and wipe clean. Applying wall primer with brush with mineral turpentine 8 to 10% and oil 15 to 20% with roller Scrapping Emery paper 320 and wipe clean, interior wall finish luster 1st coat with brush/rubber/spray with mineral turpentine 7 to 9% and Oil with roller 19 to 21% After 8 hours of activity Applying 2nd coat or wall finish Lustre with mineral turpentine 7 to 9 % with brush and Oil with roller 19 to 21% after allowing dry for the period of 6 to 8 hours activity. (With prior approval of S.E.)- on Walls and Ceilings. |
| 27 | Providing and applying antipeel paint of approved make & approved brand exterior Emulsion paint of approved quality, colour and shade to old and new surface in two coats, including exterior acrylic primer coat, scaffolding, preparing the surface etc. complete (Heat Reflective Paint) |
| 28 | Providing and applying two coats of synthetic enamel paint of approved colour to new /old structural steel work and wood work in buildings, including scaffolding if necessary, cleaning and preparing the surface (excluding primer coat) etc. complete. |
| 29 | Providing and applying 1.5mm thk 2 coats of stucco plaster of approved colour and shade on the wall, with Limocoat sealer and finish as final coat that gives smooth, flat and durable finish constructed in accordance with specialist’s requirements. Substrates must be free of curing compounds, dust, and other impurities such as oil, grease, salts and overspray/application of other Acrylic/PU/Oilpaint, etc. Apply smooth layer of Limocoat Paste Keycoat. Make sure there are no uneven surfaces. Any rough area or raised area will reflect in final finishing so care must be taken to apply a smooth even keycoat. Apply 2 thin coats of Stucco plaster (in successively thinner layers in one day). The First coat should be 40-60% dry, depending upon the final finish desired. By drying 1st coat more than 60%, you can achieve rough textures. |
| 30 | Providing and fixing 3 mm thk cementatious Polymer modified Nano topping with density of 3200 kg/cu.m on a leveled surface. The material to be applied as per manufacturer's specifications with a trowel and cure it for 96 hours. Item to include 4 coats to be done to achieve the total thickness of 3mm including the first base coat of E21 polyurethane based primer, then applying fibre mesh and then first coat of nano topping. The second coat to be applied after a minium curing of 2 hours upto the fourth coat. The final application to be of a PU sealer in the ratio of 100:25:300, followed with apoxy coating and furhter with a matt finish PU sealer in the ration of 100:25. The colour of the nano toppin surface material to be as selected by the Architect. |
| 31 | Providing & fixing 450 mm deep storage of design and size as per detailed drawings provided by the Architect. Storage to be built in 19mm thick marine plywood used for top, verticals & internal shelves dividing the internal space in equal parts as per requirement, 8mm thk commercial plywood used for backing & 19mm thick commercial block board for shutters. Shutters to be raised from the floor by 19mm & the storage base shall be 38mm thick. All exposed surfaces of the storage shall be finished with veneer with melamine polish/duco paint of approved make with all exposed edges & the internal surfaces shall be finished with french polish. Storage rate shall be inclusive of adhesive, all the hardware like nails, screws, hinges, locks, handles, towerbolts ball catch, castor wheels etc. required to complete the item. All exposed hardware shall be brushed steel finish. Mode of Measurement - Item to be paid as per the lenght x height of the storage cabinet |
| 32 | Providing and fixing laminate finish 25mm thick marine plywood shutters for a pantry's under counter storage 1mm thk. white laminte. As per design and pattern as instructed by the Architect. Shop drawings to be approved by the Architect beforefixing the storage with all necessary hardwares. D handle - 4-5inches |
| 33 | Providing and constructing granite kitchen platform with fixing of stainless steel sink 600mm x 450mm size as per detailed drawing including vertical both side polished kadappah stone 25 to 30mm thick supports with kadappah top 35 to 40mm thick and polished granite 16 to 20mm top with side strips of granite at front and both sides of platform raised with two vertical granite supports 15 cm height and top granite of 75 x 40 cm including cutting, opening for sink of required size in kadappah as well as granite etc. complete. (Platform top size 5.00 m x 0.60 m and height is 0.75 m) |
| 34 | Providing and fixing 65mm thk inclusive of 10mm thick bevelled rectangular Mirror backed on 19mm thick marine base ply with a 2-3mm thk SS 304 edging on the trim fixed on 30x30mm CP teakwood grid and backlight as per design and drawing and as instructed by the Architect. Inclusive of all SS Hardware, strip lighting and fixing to wall. |
| 35 | Providing water proof bedding for flooring of Bath and WC 25 mm thick in C.M. 1:3 including using approved water proofing compound in specified proportion as per manufacturers specifications for per bag of cement including leveling, curing and covering 10 years guarantee on court fee stamp paper of Rs.500/- including ponding test etc. complete |
| 36 | Providing waterproof plaster in W.C. and bath 12 mm thick for dado in cement mortar 1:3 with neat finishing, floating using waterproofing compound at the rate of 1 Kilogram. per bag of cement of approved make and manufacturer and curing etc. complete. (Excluding Tiles) (As directed by Engineer in Charge |
| 37 | Providing waterproofing in W.C. and bath including brick bat coba in all position including providing and laying 12mm bedding in cement mortor 1:3 on vergin concrete slab with waterproofing compound @ 1Kilogram/per bag of cement laying brick bat coba of required thickness in cm 1:5 with waterproofing compound 1 Kilogram/bag of cement grouting and finishing the top layer with 20mm thick brick bedding in cm mortor 1:3 with waterproofing compound 1 Kilogram/per bag of cement and testing the treated portion for 48 hours by pond test and covering ten years' guarantee on requisite stamp paper including curing etc. complete. |
| 38 | Providing and fixing frame with / without ventilator of size as specified with Country cut teak wood for doors and windows including chamfering, rounding, rebating, iron holdfast of size 300mm x 40mm x 5mm with oil painting, etc. complete |
| 39 | Providing and fixing in position, Double leaf flush door of required size including providing & fixing T.W. frame 60mm x 150mm., 45mm thick solid code hard wood block board shutters with 25mm x 45mm lipping patti, alround the shutter & finished with 10mm thk. flutted panel on either sides, finishing all exposed surfaces of wood with approved shade of Melamine polish, treating all the surfaces of wood in contact with masonary with tar paint (Black Japan), chrominum plated brass fittings & fastenings, wooden handles etc. complete as per detailed drawing and as directed by the Engineer In charge. |
| 40 | Providing & fixing in position single leaf flush door of required size for internal doors of residential units, shutters made of 45mm thick marine grade block board core with 25mm x 45mm T.W. lippingpatti, 1mm thick approved 10mm thick flutted panel on both faces of shutter, including providing & fixing T.W. frame of 60mm x 150mm size,coating all the exposed surfaces of wood with MELAMINE POLISH of approved shade & make, coating all the surfaces of wood in contact withmasonary with Tar (Black Japan), preparing the surfaces, providing and fixing wooden handle & brass chrome finished or S.S. fittings and fastenings etc complete. |
| 41 | Providing and fixing Stainless Steel 1.5mm (SS304) in the form sheets, channels, plates etc 0.4mm all required members to be transformed into partitions, doors for toilets with all accessories like hinges, locks etc as indicated by the Architect. |
| 42 | Providing & fixing 12mm thk toughened clear fixed glass door of Saint Gobain/Asahi/equivalent make upto ceiling height 4200 mm. The glass door of size approx. 4200mm x 2000mm. Item to include fixing of wooden handle as per drawing and design. Door rate shall be inclusive of all the hardware like floor springs, lock , handles etc., required to complete the item. Shop drawings to be approved by the Architect. |
| 43 | Providing and fixing BTC wooden Single shutter Pivoted door of 65mm thick door flutted shutter and 20mm dia. pivot rod system concealed in the ground and ceiling. The door handle made out of BTC wood as per Architectural design and drawing. Item to include fixing of lipping patti alround the shutter, melamine polish to door, etc. complete. |
| 44 | Providing and fixing in position aluminium fixed window fully glazed of any size as per detailed drawing and as directed by Engineer in charge with all necessary alluminium sections including necessary fixtures and fastening such as 5mm thick clear float glass etc. complete.Colour Anodized. |
| 45 | Providing and fixing partly fixed partly openable type window having made out of BTC wooden shutters as per design & drawing including providing & fixing T.W. frame 50mm x 100mm., 30mm thick solid Teak wood shutters with 30mm lipping patti, alround the shutter & finished with melamine polish on either sides. Item to include plain / frosted / tinted glass of 6mm thickness shall be fixed on the top with BTC wooden frame. Item to include fixtures & fastening, holdfasts embedded in cement concrete grade M15, melamine polish, etc. complete as directed by Engineer In Charge. |
| 46 | Providing and fixing in position FOLDABLE aluminum louvered window with anodised aluminum frame of approved make and of size 40mm x 20mm x 2.0mm (wt.0.605 kg/Rm) including adjustable aluminum frame, 4 to 6mm thk. frosted glass, fixtures and fastenings etc. complete as directed by by Engineer In Charge. |
| 47 | METAL OPEN CELL CEILING: Providing & fixing horizontal level Open cell Aluminium lay-in ceiling tiles with border panels forming board edge of size 600x600x38mm (Nominal)having cell size of 100x100mm made of AA-3003-H14 (Tempered grade Aluminium suitable for architectural finishes in 0.35mm thickness as per in IS:2676(1981) in Global white color. |
| 48 | METAL BAFFLE CEILING: Providing & fixing of horizontal level suspended ceiling comprising of Vertical Linear Baffle Ceiling made out of Aluminum Extrusion in Aluminum alloy grade 6063 T5. The baffle blade shall be in size of 100 x 25 x 3600mm in powder coated to Woodgrain / Plain finish (RedOak, Cherry, Black & White). |
| 49 | Providing & fixing Armstrong Orcal Lay in metal ceiling System consisting of 600x600mm Lay in tiles of pre coated galvanised steel in 0.5/0.4 mm thickness in white colour with standard perforation of 2.5mm dia & open area of 16%. The back of the tile should have black acoustical fleece with NRC of 0.70 & CAC 36 with life time warrantee against sag in module size 595 mm X 595 mm at required height above FFL. |
| 50 | PROVIDING AND FIXING ANTIMICROBIAL ACOUSTICAL FALSE CEILING:Bioguard Mineral Fibre Acoustical Suspended Ceiling System with 19mm thick Acoustics Microlook 90 Edge Tiles with 15mm face exposed grid. The tiles shall have smooth bright laminated visual with Humidity Resistance (RH) of 99%, NRC 0.7 (Average value of Absorption Co-efficient readings taken at 250 Hz, 500 Hz, 1000 Hz and 2000 Hz) as per ASTM C423 standard, CAC of 41db as per ASTM E1414, Light Reflectance ≥87% as per ASTM E-1477, Thermal Conductivity k = 0.052 - 0.057 W/mK, Colour Global White, Fire Performance of Class 0/1 as per BS 476 Part6/7 and Class A as per ASTM E 84 with 19mm Square Tegular/Microlook 90˚ edge and 8mm drop in module size of 600 x 600mm./ 600x1200mm. The scrim on the face of the tile shall be cleanable, washable up to 500 cycle as per ASTM D-4828 and resistant to disinfectants. |
| 51 | Supplying and fixing of 6mm thick Exterior Compact Laminate or High Pressure Laminate of approved colour by approving authority with UV resistant Decorative colour paper on both side typically made out of multiple layers of craft papers and then impregnated with thermo setting phenolic resins, on top of it melamine treated barrier paper and decorative paper and wear layer on both the sides saturated with melamine resins and then covered with UV resistant acrylic resin layer which makes it extremely durable and weather resistant compressed together on extremely high pressure and hardened with electron beam curing to get the total desired thickness of 6mm matching European standard specification as per EN438- part 6, protected with 60 Micron protective peel-off film on both side which in no case leave any adhesive mark over the panel surface after it is peeled off. |
| 52 | Supply & Fixing of Rectified Porcelain Stoneware Tiles for Ventilated Facades of Specified size as per specification/site drawings having 6mm and 9mm thickness with factory made Kerfs (grooves) as per need and size 600/1200 and 800/1600. The Rectified Porcelain Stoneware Tiles shall possess properties having Water absorption <0.5 Bending Strength > 40N/mm2 and are resistant to: UV Light, chemicals, smog, thermal shocks & bacteria. The facade will be made from Nexion Rectified Porcelain Stoneware Tiles (Sintered Compact Surfaces)specified as per ISO13006 :Annex G-EN14411: Annex G: Dry Pressed Ceramic Tiles and all the tests carried out by Italian labs accredited according to ISO / IEC 17025:2005. |
| 53 | Providing and fixing structural steel frame (for dry cladding with 30 mm thick gang saw cut with machine cut edges sand stone) on walls at all heights using M.S. square/ rectangular tube in the required pattern as per architectural drawing, including cost of cutting, bending, welding etc. The frame work shall be fixed to the wall with the help of M.S. brackets/ lugs of angle iron/ flats etc. which shall be welded to the frame and embedded in brick wall with cement concrete block 1:2:4 (1cement :2 coarse sand :4 graded stone aggregate 20 mm nominal size) of size 300x230x300 mm, including cost of necessary centring and shuttering and with approved expansion hold fasteners on CC/RCC surface, including drilling necessary holes. Approved cramps/ pins etc. shall be welded to the frame work to support stone cladding, the steel work will be given a priming coat of Zinc primer as approved by Engineerin-charge and painted with two or more coats of epoxy paint (Shop drawings shall be submitted by the contractor to the Engineer-in-charge for approval before execution). The frame work shall be fixed in true horizontal & vertical lines/planes. (Only structural steel frame work shall be measured for the purpose of payment, stainless steel cramps shall be paid for separately and nothing extra shall be paid). |
| 54 | Providing and fixing adjustable stainless steel cramps of approved quality, required shape and size, adjustable with stainless steel nuts, bolts and washer (total weight not less than 260 gms), for dry stone cladding fixed on frame work at suitable location, including making necessary recesses in stone slab, drilling required holes etc complete as per direction of the Engineer-in-charge. |
| 55 | Design and supply and fixing fully fixed semi unitized structural glazing system including with SPIDER FITTINGS as specified: Glass panel shall be 13.5mm thick (6mm + 1.52mm + 6mm) glass unit. Outboard glass shall be 6mm thk heat strenghten. Glass shall be of approved colourand shade and having air gap with aluminium / SS Fin brackets for stabilizer with single joint and having 6mm thick toughened glass. The refelctive coating shall be on surface no.2. The insulated glass unit shall be hermetically using primary sealant. The cost includes providing and applying masking at site. Price inclusive of all structural system. |
| 56 | Providing and fixing Exterior Grade fin Systems of Aluminium structured with cement bonded fiberboard or High pressure laminate panels (wood finish or any other material) by TDW FACE (VRLS Plain) inclusive of / with aluminium box section framework as per manufactures specifications) All inclusive as per Architects approval and manufacturers installation specification. Fin size to 450mm x 3600mm. (TDW FACE (VRLS PLAIN) |
| 57 | Providing and fixing Perforated Corten steel - 4 mm perforated sheets durable, robust & corrosion resistant A588 grade A or B by VMZinc, JSW or equivalent approved shade and finish as selected to be fitted on external face of the building as indicated by the Architectural drawings. |
| 58 | Providing preconstructional antitermite treatment as per I.S. 6313 (Part-II) by treating the bottom surface and sides of excavation at the rate of 5 litres of emulsion concentrate of 1.0 percent of chlorophyrifos per square meter of surface area covering 10 years guarantee on bond paper. |
| 59 | Providing preconstructional antitermite treatment as per I.S. 6313 (Part-II) treatment by treating the backfill in immediate contact with foundation at the rate of 5 litres of emulsion concentrate of 1.0 percent of clorophyrifos per One Square Metre of vertical surface area covering 10 years guarantee on bond paper. |
| 60 | Providing preconstructional antitermite treatment as per I.S. 6313 (Part-II) by treating the top surface of plinth filling at the rate of 5 litres of emulsion concentrate at 1.0 percent of clorophyrifos per One Square Metre of surface area covering ten years guarantee on bond paper. |
| 61 | Providing preconstructional antitermite treatment as per I.S. 6313 (Part-I) to the soil along the external face of building by punching holes of 1.2 of 1.5 C.M. diametre about 30 -60 cm deep at 15 cm c/c as close to the wall as possible and to inject 0.5 percent of aldrin or clorophyrifos at the rate of 7.5 litres per hole and sealing the same with proper filling and covering 10 years guarantee on bond paper. |
| 62 | Providing and fixing mild steel grill railing weighing 15 Kilogram/ One Square Metre. with teak wood hand rail of size 75mm.x 60mm. and sill 75mm.x 25mm.and posts for verandah including fabricating, fixtures, erecting and painting the grill work with one coat of anticorrosive paint and two coats of enamel paint and polishing the grill, hand rail with French polish. |
| 63 | Providing and fixing 10 mm dia SS 304 cables fixed to slab 3.5 mm SS screws using 5 mm thk SS plates fixing all complete as approved by the Architect |
| 64 | Providing and fixing teak wood handrail of 60mm x 75mm as per detailed drawings or as directed by the Engineer, including french polishing, etc. complete. |
| 65 | Providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc. including welding grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories and stainless steel dash fasteners, stainless steel bolts, etc.of the required size on the top of the floor of the side of waiste slab with suitable arrangement as per approval of engineer in charge (for payment purpose, only the weight of the stainless steel members shall be considered excluding fixing accessories such as nut bolts, fasteners etc.) 50mm dia.pipe,1.5mm thickness and weight 1.92 Kilogram/ r. metre |
| 66 | Providing and fixing C.P teak wood ceiling planks of 25 mm thk as per existing detail, tongue and grooved including scaffolding if necessary and one coat of primer complete. Item to include all mouldings and chamfers to be made as per original design indicated by the Architects. Item to include using a larger section of wood to get the mouldings and chamfers as per original design, sample to be shown to the Architect for approval before fixing. |
| 67 | Design, Supply, fabrication & installation of suitable steel framework and accessories as required, the structural skylight which shall be cladded with 8mm clear toughened + 1.52 PVB lamination or advanced + 8mm toughened clear toughened, including all necessary fixtures, fittings as per the technical specifications. |
| 68 | Providing and fixing 5mm thk laser cut MS cut letters (250-300MM high) with design as per Architect's apporval with the means of ms rod and ms frame for fixing where necessary the plate to be fixed with MS frame and MS base plate for making it free standing and finished with 1 coat of zinc primer anti corrosive paint and 3 coats of synthetic enamel exterior paint. Item to be inclusive of all fabrication and fixing with anchors, bolts, and hardware to fix on any surface. Item to be inclusive of sample for Architect's approval. |
| 69 | Providing and fixing 100-150mm high Individual cut SS letters chrome finish / Nickel plated brushed gold finish around 5-8mm thick of approved finish, to be glued to door lintels or any other area as indicated in the drawing or as directed by the Architect. Item to be inclusive of all fabrication and fixing with anchors, bolts, and hardware to fix on any surface. Item to be inclusive of sample for Architect's approval. |
| 70 | Providing and fixing eco vinyl prints of signage text printed in required colour to be pasted or installed on the glass panels or any other surface of approved size and design as directed by by the Architect. Vinyl sheet to be installed taking utmost care to avoid any stains on glass panels, formation of any air bubbles etc. In case of the installation or printing is found unsatisfactory the sheet to be replaced with new with necessary corrections as part of rectification works. Item to include all necessary tools, vinyl and printing, scaffolding if required etc. complete |
| 71 | Providing and fixing ALCOBond directional signage of 500mm x 500mm size using MS frame 25mm x 25mm along with 2-3mm thk Aluminum sheet fixed to the framework as shown in the ref image fixed to on an existing wall. The signage to also include transparent Vinyl graphics / letters/symbols etc. Rate to be inclusive of vinyl printing & providing, fixing and installation etc. complete. and of all hardware. |
| 72 | Providing and fixing Introductory signage of 450 mm x 300 mm height and 30 mm in depth using 25mm & 20mm thk Marine ply for the framework along with 5mm thk x 10mm Chrome / brass strip bent on the edges to give a seamless finish. All letter to be made in chrome/brass cut letters 40mm high & 3-5mm thk in both Marathi & English. Ply to be DUCO painted finish to give a seamless look. Item to include all hardware in SS 304 inlcusive of channels etc for anchorage and giving sturdity to the signage. Item to include Vinly printing as well as laser cutting for letters and other graphics as mentioned in as many colours as required. |
| 73 | Providing and fixing Information Signage using 3-5mm thk ALCOBond/Aluminum/Zinc sheet of size 150mm x 300mm including bending the sheet as per reference photo including graphics/lettering of vinyl transparent sticker. Rate to be inclusive providing, fixing and installation etc. complete. Item to include all hardware in SS 304 inlcusive of channels etc for anchorage and giving sturdity to the signage. |
| 74 | Providing and fixing 150-200mm high 3-5mm thk individual cut Zinc sheet symbol / letters anchored into the ground or fixed in the wall with anchor fastners coated with anti rust paint. Item to be inclusive of all fabrication and fixing with anchors, bolts, and hardware to fix on any surface. Item to be inclusive of sample for Architect's approval |
| 75 | Providing & Fixing signage made of 15 mm thick solid white acrylic laser cut out letters for height up to 25\\" etc complete |
| 76 | LED lit sigange 200 x 200 x 100 mm size of Prolite make or equivalent to be fixed atop external Fire escape doors with approved graphics as directed by the Architect. |
| 77 | Providing and fixing of equivalent Photoluminescent Signage- Man with running arrow PEL LED E/M 190 x 220 mm facia all complete as per manufactures specifications |
| 78 | Providing and fixing of equivalent Photoluminescent Signage- fire extinguisher signage 250 x 200 mm all complete as per manufactures specifications |
| 79 | Providing and fixing of equivalent Signage- push bar to open doors signage 120 x 680 mm all complete as per manufactures specifications |
| 80 | LED lit EXIT / ENTRY sigange 200 x 100 x 100 mm size of equivalent to be fixed atop AUDITORIUM doors with approved graphics as directed by the Architect. |
| 81 | Providing Six seater Frank table of equivalent: Size - W190cm x D100cm x H70cm |
| 82 | Providing Lou - White Chair of equivalent Dimension: W60cm x D50cm x H82cm SH44cm Weight: 3 KG Primary Material: Plastic, PolyPropylene(PP) Shell, Solidwood+MS frame |
| 83 | Providing Carson Chair of equivalent: Material Specification:Foam and upholstered seat in fabric / leatherette. Teakwood / Ashwood / Beechwood legs. (Fabric / leatherette can be customised) Dimensions: W53cm x H 78cm X H78cm X SH45cm |
| 84 | Providing and supplying 700mm long 1-seater sofa having rattan back, side arms with BTC framing, wooden arms and seat as per the design in the image. The sofa shall be with an internal frame work of old CP teakwood and legs in CP teak wood and french polish. The to have cushions as for seat and bakrest upholstered with fabric as shown in the image, using high density U-foam (Navar kantan) finished with fabric/leather of the approved colour and texture |
| 85 | Supplying and fixing - the side table/ coffee table of 0.45m x 0.45m upto a height of 400mm as per image shown. Tables to be made in hard wood like teak wood or seesham wood with cruved/ straight legs as per image. Item to include making carved or moulded legs and rims as detailed by the Architect at the time of execution. Item to include 25mm table top with curved edge profile as approved by Architect. Table to be finished in french polish finish on all exposed surfaces and inside of drawer as approved by the Architect. Item to include spray coating all the surfaces with approved anti termite solution including providing 10 year guarantee for the same as directed by the Architect or Engineer in Charge. |
| 86 | Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material up to a distance of 50m. beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary backfilling, ramming, watering including shoring and strutting etc. complete. (Lift upto 1.5 m.) By Mechanical Means |
| 87 | Excavation for foundation in earth, soils of all types, sand, gravel and soft murum, including removing the excavated material up to a distance of 50 metres beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary backfilling, ramming, water ingincluding shoring and strutting etc. complete. (Lift from 1.5m to 3.0m) By Mechanical Means |
| 88 | Excavation for foundation in Soft rock and old cement or lime masonry foundations including removing the excavated material up to a distance of 50 metres beyond the building area and stacking as directed, including dewatering, preparing the bed for the foundation and necessary backfilling with available earth/murum, ramming, watering including shoring and strutting etc. complete (lift upto 1.5m) By Mechanical Means |
| 89 | Dewatering on BHP basis by using water pump including diversion of stream, providing cofferdams, earthern bunds etc. as may be necessary for foundation and other parts of the the works and pumping out water during and after excavation as may be required by using 3.0 BHP pump etc. complete. (prior approval of Superintending Engineer will be necessary) |
| 90 | Filling in plinth and floors with approved excavated material in 15cm .to 20cm. Layers including watering and compacting etc. complete. |
| 91 | Filling in plinth and floors with contractors material/brought from out side and approved by Engineer in charge in layers of 15cm to 20cm including watering and compaction etc. complete. |
| 92 | Providing dry / trap / granite / quartzite / gneiss rubble stone soling 15cm to 20cm thick including hand packing and compacting etc. complete. |
| 93 | Providing and laying Castinsitu / Ready Mix cement concrete in M20 of trap / granite / quartzite / gneiss metal for bed blocks, foundation blocks and such other items including bailing out water, Steel centering, formwork, laying / pumping, compacting, roughening them if special finishis to be provided, finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed), with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer / concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) |
| 94 | Providing and laying Cast in situ / Ready Mix cement concrete M-40 of trap / granite / quartzite / gneiss metal for R.C.C. work in foundations like raft, strip foundations, grillage and footings of R.C.C. columns and steel stanchions etc. columns as per detailed designs and drawing or as directed including steel centering, formwork, cover blocks, laying / pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete. (Excluding reinforcement, including cover block). (Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer / concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) |
| 95 | Providing and laying Cast in situ / Ready Mix cement concrete in M-40 of trap / granite / quartzite / gneiss metal for R.C.C. pardi of required thickness including steel centering, formwork, cover blocks, laying / pumping, compacting, curing, finishing and roughening them if special finish is to be provided and curing complete. (Excluding reinforcement, including cover block). (Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer / concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) |
| 96 | Providing and laying Cast in situ / Ready Mix cement concrete M-40 of trap / granite / quartzite / gneiss metal for R.C.C. slabs and landings as per detailed designs and drawings including steel centering, formwork, coverblocks, laying / pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete. (Excluding reinforcement, including cover block). (Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer / concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) |
| 97 | Providing and laying Cast in situ / Ready Mix cement concrete M-40 of trap / granite / quartzite / gneiss metal for R.C.C. beams and lintels as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks, laying / pumping, compaction and roughening the surface if special finish is to be provided and curing etc.complete. (Excluding reinforcement, including cover block). (Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer / concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) |
| 98 | Providing and laying Cast in situ / Ready Mix cement concrete M-40 of trap / granite/ quartzite / gneiss metal for R.C.C. columns as per detailed designs and drawing or as directed including steel centering, formwork, cover blocks, laying / pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete. (Excluding reinforcement, including cover block). (Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer / concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) |
| 99 | Providing and laying Cast in situ / Ready Mix cement concrete in M-40 of trap / quartzite / granite / gneiss metal for R.C.C. Waist slab, and steps of staircases as per detailed design and drawings or as directed including steel centering, formwork, steel props, laying / pumping, compaction, finishing uneven and honeycombed surface with C.M. 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening the surface if special finish is to be provided and curing etc. complete. (Excluding reinforcement, including cover block). (Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer / concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) |
| 100 | Providing and laying Castinsitu / Ready Mix cement concrete M-20 of trap / granite / quartzite / gneiss metal for R.C.C. chajja as per detailed design and drawings including steel centering, formwork, cover blocks, laying / pumping, compacting and roughening the surface if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer / concrete Batch mix plant (Pan mixer)etc. complete. With fine aggregate (Crushed sand VSI Grade). |
| 101 | Providing and fixing in position HCRM / CRS (Corrosion Resistant Steel)bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete. |
| 102 | Providing and applying epoxy paint primer with middle coat and top coat to superstructure including scaffolding etc complete.m i.e to RCC Beams, columns and other members etc. |
| 103 | Providing and fixing 20 to 25 mm thick rough shahabad box type water proofing for basement or under ground floor on a base of Cement concrete 1:3:6, including sub base of 2.50 centimeter thick Cement mortar 1:3 with conceal, secrete (RMW), Algae proof or other alike water proofing liquids, raking of joints up to 35mm depth, filling the joints with 6mm size crushed metal, hand grouting with cement slurry, curing and cleaning, with 7 years guarantee on court fee stamp of Rs.100/-with ponding test etc. complete. (excluding Cement concrete 1:3:6 base concrete ) |
| 104 | Providing and fixing 20 to 25mm thick rough shahabad box type waterproofing treatment to vertical out side faces of Reinforced Cement concrete walls of basement or under ground floor including filling the gap of 25mm between rough shahabad and R.C.C. walls with cement grout mixed with waterproofing liquid Algae proof or other alike with one tile lift method, brushing the joints horizontally with cement slurry mixed with water proofing liquid for width 30 to 35mm and sloping coping over top most tile with cement mortar 1:3, butting the bottom most with Cement concrete 1:2:4 mixed with water proofing liquid, curing, with 7 years guarantee on court fee stamp of Rs.100/-with ponding test etc complete. (excluding Cement concrete 1:3:6 base concrete) |
| 105 | Providing and fabricating structural steel work in rolled sections, fixed with connecting plates or angle cleats in main and cross beams, hip and jack rafters, purlins connecting to truss members and the like, as per detailed designs and drawing or as directed including cutting, fabricating, hoisting, erecting, fixing in position, making riveted / bolted / welded connections and one coat of anti corrosive paint and over it two coats of oil painting of approved quality and shade etc. complete. |
| 106 | Providing structural steel work in trusses, othe rsimilar trussed purlins and members with all bracing, gusse t plates etc. as per detailed designs and drawings or as directed including cutting, fabricating, hoisting, erecting fixing in position, Making riveted / bolted /welded connection and one coat of anti corrosive paint and over it 2 coats of oil painting approved quality and shade etc. complete. |
| 107 | Providing and carrying out metallizing the steel structure immediately after sandblasting the surface with approved zinc metal to a thickness of 200 DFT. This shall be done as per IRS Standards adopted by Railways RDSO. |
| 108 | Providing and carrying out sand blasting the steel surfaces of trussess, purlins, base plates, gussets and all other types of steel structures with quartz sand and cleaning the surface to the required Sa21/2 level as per IS 9954l.( Sandblasting to be done off site) |
| 109 | Providing and applying Polyurethane Paint to all Structural Steel Sections including tubular sections in one primer coat and two final coats in specified color at all heights including labour, scaffolding and touch up as and where required all complete. ( Item to be quoted as extra over paint item instead of oil paint for structural steel rate which is inclusive of oil paint.) |
| 110 | Providing and fixing 975 wide, 0.71 mm trapazoidal Aluminium Sheets ( 2.41 kg/m2) out of Alloys - AA 8011 and AA 3105 in approved colour including fixing accessories, overlapping the sheets as per specifications. Length of the sheets should be provided in single/maximum length possible as no joints occur long the width of laying. |
| 111 | Providing and fixing 975 wide, 0.71 mm trapazoidal Aluminium Sheets ( 2.41 kg/m2) out of Alloys - AA 8011 and AA 3105 in approved colour including fixing accessories, overlapping the sheets as per specifications. Length of the sheets should be provided in single/maximum length possible as no joints occur long the width of laying.same as for Ridge. |
| 112 | Providing & laying 2.1 mm THK SBS modified self adhesive,cross laminated HDPE valeron lining waterproofing membrane, Dr. Fixit Samshield XL 2100, with the execution to be done by the manufacturers authorised / trained / partner applicator with 10 years warranty against leakages, over the solvent based bituminous Torchshield primer @ 4 sqm/litre. This shall includes Surface Preparation by cleaning work, i.e. smoothening the wooden surface of all the to even out all the rough edges the jutting fibres and kinds of impurities, moreover, the wooden surface should be dry and smooth as per manufacturers’ recommendation, all followed by termination of the membrane minimum 200mm above FL with aluminum termination bar shall be fixed with non corrosive fastener @ 4 nos per RM, sealing of termination bar with PU Sealant / epoxy mortar / putty, as per manufacturer specification, etc. complete. The SBS membrane shall have Roll Size: 1 Mtr X 10 Mtr, Mass per Unit Area > 2.3 Kg/m2 as per ASTM D 5147,Puncture resistance > 200 N as per ASTM E 154,Elongation > 180% as per ASTM D 412-06,Crack bridging (10 cycles) > 1.5mm as per ASTM C 836 Tensile Strength > 4 Mpa as per ASTM D 412-06, Tear resistance > 20 N/mm as per ASTM D 4073, Softening Point (oC) ≥ 105 as per IS 1205/1978 ,Low temperature Flexibility – 10 degC as per ASTM D 5147,Chemical Resistance (pH) as per ASTM D 543, |
| 113 | Carting away excavated materials/debris from site to the designated dumping ground |
| 114 | UNDER DECK CEILING: Providing and fixing G.I 'C' section 50 x 37.5 x 0.8 mm thkat 500 c/c in one direction & at 1000 c/c in other direction with between frame have polyester wadding of 50mm thk,1000 gsm density + Black tissue paper. Entire frame/Polyester wadding shall be covered welded mesh of G.I 19 mm x 19 mm square of 14 guage (as per approved sample) including Polyester wadding,black tissue paper,machine screw & levelling & scafolding etc. |
| 115 | GYPSUM BOARD CEILING: Providing and fixing panels – 12.5mm thk India Gypsum plain tapered edge gypsum panels, screwed to G.I. Frame at 200mm c/c. FRAME – G.I frame fabricated with 80x26x0.5 ceiling sections at 300 c/c, 20x27x30x0.5 perimeter channel as required, 15x45x0.9 inteR.mtediate channel at 1220 c/c, 25x10x0.55 ceiling angle at 1220 c/c, securely fixed to structural sofit hangers at 1220 c/c, last ceiling angle not more then 610 from adjacent wall, connecting clips etc. as required. Complete as per manufacturer’s specifications.JOINTS - All joints of panels filled and finished with India Gypsum jointing compound, jointing tapes etc. complete. including 50 mm thk polyester wadding of , 1000 gsm density in between g.i frame & scaffolding. Entire frame/Polyester wadding shall be covered welded mesh of G.I 19 mm x 19 mm square of 14 guage. Cost inculdes making necessary cut-outs for lights , speakers , sprinklers , fire detectors, HVAC grills etc all as per details complete as per design, drawings and acoustic consultants instruction. AUDITORIUM & CONTROL ROOM |
| 116 | PERFORATED GYPSUM BOARD PANELING: Providing and fixing 595 x 595 x 12.5 mm thk Perforated gypsum plain tapered edge panels screwed to G.I. framework, complete, at all heights as per detail dwgs & as directed by Engineer. FRAMEWORK - G.I. framework fabricated with 50 x 37.5 x 0.5 G.I 'C' section at 1220mm c/c in horizontal direction fixed away from wall on 50 x 50mm wooden 'T' dutta supports with 50mm air gap. Over the 'C' sections, Ceiling sections of 80 x 26 x 0.5 at 300mm c/c in vertical direction shall be fixed, with 50mm thk 1000 GSM density polyester wadding placed between the framework. Entire framework & polyester wadding shall be covered with welded mesh of G.I 12 mm x 12mm square of 24 guage (as per approved sample) JOINTS - All joints of panels filled and finished with India Gypsum jointing compound, jointing tapes etc. to be in one line and level. TOP COAT - Entire face of panelling shall be finished with one coat of primer & three coats of paint of approved colour & shade. NOTE : Pidilite Terminator Wood Preservative shall be applied on all wood, before fabrication. G.I frame work & will have 100x100 x12mm thk rigged rubber behind |
| 117 | GRIPPER + FABRIC SYSTEM: Providing & fixing Gripper system of Walltracks (I) Pvt.Ltd stretch fabric system (UK) UPVC Grippers, standard, Cove,mono,edge, but as required by design & manufacture's specifications. CORE - Fire retardant compressible polyster padding of 12 mm thk. FRAME : Wall track fix on 75 x 12mm ply putty as required by design. INSTALLATION : Installation in accordance with drawings and manufacturer's instruction. Installation of grippers in maximum length possible. From end-to-end butt joints with hairline. Joints locations shall not be visible in finished work.Install grippers so that joints between core material & grippers are not visible in finished work, rebate edge of rigid core material for flush fit.Install fabric without wrinkles or folds, maintaining horizontal/ vertical alignment of warp/woof of fabric, force fabric edges into clamping jaws, using tools & techniques that will not damage finish of the fabric. SUBMITTALS : Drawings indicating, location, size, type,including frame, core & fabric finish components, for each panel in project. Drgs indicating construction details of interface with adjacent construction. The rates shall includes the shapes, pattern as mentioned in the drawing indicating graphics. Note : Fabric shall be fire retardant install fabric without wrinkles or folds maintaining horizontal/ vertical alignment of warp/ woof of fabric using technique that will not damage finish of the fabric. |
| 118 | TRELLIS PANELING - Providing & fixing of Trellis in Teakwood 19 x 19 mm thk as per design pattern on Fabric with necesssary support for fixing in proper line & level . Trellis as approved by Acousitc Consultant with sanding, leveling and 3 coats of melamine polish complete. |
| 119 | Providing & Fixing T.W. Rafter of size 75 x 50mm thk as approved by Acousitc Consultant with sanding, leveling and 3 coats of melamine polish complete. |
| 120 | L PELMET IN VENEER PANELING: Providing & Fixing of L pelmet in 150 x 100 mm thk on G.I frame work on 12 mm thk. comm ply with 4.5 mm thk. veneer as approved by Architect.3 coats of melamine polish on veneer surface and complete with machine sanding, leveling, applying hard putty, filling gap etc. Including 50 mm thk,1000 gsm density polyester wadding in between frame. Anti-termtite treatment to internal surface of frame & ply by Aldrex complete with scaffolding etc. |
| 121 | VENEER PANELING: Providing & fixing 4 mm thk Veneer Panelling on 12 mm thk fire retardant plywood fixed on G.I. framework, complete, at all heights as per detail dwgs & as directed by Engineer. FRAME WORK - G.I framework fabricated with 80 x 26 x 0.5 ceiling sections @ 300mm c/c, with perimetre channel as required, 15 x 45 x 0.9 intermediate 'C' channel @ 1220mm c/c, 25x10x0.55 ceiling angle securely fixed to structural sofit hangers @ 1220mm c/c, last ceiling angle not more then 610 mm from adjacent wall, connecting clips etc as required, complete as per manufacturer’specifications with 50mm thk 1000 GSM density polyester wadding placed between the framework. Frame shall be covered by 12 mm thk. comm ply with 4.5 mm thk. veneer as approved by Architect.3 coats of melamine polish on veneer surface and complete with machine sanding, leveling, applying hard putty, filling gap etc. Including 50 mm thk,1000 gsm density polyester wadding in between frame. Anti-termtite treatment to internal surface of frame & ply by Aldrex complete with scaffolding etc. (Basic rate of Veneer - 1500/Sq.Mt.). NOTE : Pidilite Terminator Wood Preservative shall be applied on all wood, before fabrication. G.I frame work & will have 100x100 x12mm thk rigged rubber behind |
| 122 | Side wall panelling |
| 123 | Stage front panelling |
| 124 | Providing / Fixing 25 mm thk. , 100 mm high Teak wood skirting fixed by screw with 3 coats of melamine polish on hardwood frame 50 x 40, flushed with veneer paneling complete. |
| 125 | Providing and fixing 595 x 595 x 12.5 mm thk Perforated gypsum plain tapered edge panels screwed to G.I. framework, complete, at all heights as per detail dwgs & as directed by Engineer. FRAME WORK - G.I framework fabricated with 80 x 26 x 0.5 ceiling sections @ 300mm c/c, with perimetre channel as required, 15 x 45 x 0.9 intermediate 'C' channel @ 1220mm c/c, 25x10x0.55 ceiling angle securely fixed to structural sofit hangers @ 1220mm c/c, last ceiling angle not more then 610 mm from adjacent wall, connecting clips etc as required, complete as per manufacturer’specifications with 50mm thk 1000 GSM density polyester wadding placed between the framework. JOINTS - All joints of panels filled and finished with India Gypsum jointing compound, jointing tapes etc. to be in one line and level. TOP COAT – Entire face of ceiling shall be finished with one coat of primer & three coats of paint of approved colour & shade. |
| 126 | Providing & fixing 595 x 595 x12.5 Perforated gypsum tile panelling on G.I frame work finished with BLACK MATT PAINT. FRAME - G.I.frame fabricated with 50 x 37.5 x 0.5 g.i 'C' section @1220 mm c/c, Ceiling sections 80 x 26 x 0.5 @ 400mm c/c with 50 mm thk 1000 gsm density polyester wadding fixed with Chicken mesh back of g.i 12 x 12mm square of 24 guage (as per approved sample), including wooden dutta for 50 mm air Gap,scaffolding etc, work will be carried out as per drg & instruction of acoustic consultant /Site Engineer/Architect. FINISH: Perforated gypsum tile shall be finished with black matt paint Work will be carried out as per drg & instruction of acoustic consultant /Site Engineer/Architect. NOTE :All the wood shall be used will be coated with Fire painting & necessary Anti-termite treatment/Black Japan. |
| 127 | Providing and fixing 100X25mm thick solid BTC wooden flooring of 100mm wide &1200mm long with toungue and groove, joints fixed on bottom salwood framework 75 X 75mm at 587mm c/c & top salwood framework 75 X 75mm at 600mm c/c with 60mm thick sand layer , and 19mm Marine Ply on the fram will be fixed, including spreading,levelling as per drawing, all trims, edges, skirting, as per drawing etc. complete as directed. |
| 128 | Providing & fixing 1st class C.P. Teak wood moulding of size 75 x 75 mm, including sanding, levelling with two coats of french polish and two coats of melamine polish of approved shade, complete as per detail dwgs & as directed by Engineer. |
| 129 | Providing & Fixing 37 mm thk. C.P. Teak wooden step (One piece) on hard wood frame / joist as per dwg & instructions stated below. Step plank shall have 300 x 37 mm thk. with require length at site (1500 max) plank shall be fixed on necessary hard wood frame. If require on concrete step by screw. Applying three coats of Matt finishing French polish on wooden step complete machine sanding (before fixing) and leveling. Applying hard putty, filling gaps etc. complete. Anti-teR.mtite treatment to internal wooden surface of plank and internal frame by Aldrex or equivalent product. Complete with scaffolding, leveling, sanding. Size :-900 & 1400mm. In length |
| 130 | Providing & Fixing 18 mm thk C.P. Teak wooden riser (one piece) on hard wood frame as per drg and instructions stated below. Riser plank shall have 150x18 mm thk(6\\"x3/4\\" out of) with require length at site (Say 1500 mm max.) Plank shall be fixed on necessary hard wood frame (if require on concrete by screw) Applying three coats of Matt finished French polish on wooden step complete machine sanding (before fixing) & leveling. Applying hard putty, filling gaps etc. complete. Anti-termtite treatment to internal wooden surface of plank & internal frame by Aldrex or equivalent. Complete with scaffolding leveling, sanding etc. Size :- 900 & 1400mm. In length |
| 131 | Providing & Fixing Curtain housing 75 mm thk partition on salwood frame with both sides 12mm thk fire rated ply as per drg. FRAME : Treated saalwood frame of 50 x 50mm at 600mm c/c in both directions, Frame shall be covered by 12mm thk fire rated ply with 2 coats of paint finish from both sides. Anti-termtite treatment to the internal surfaces of wooden frame and back side of fire rated ply with Termtiseal (RTU) or approved equivalent including scaffolding, leveling etc complete,Work will be carried out as per drg & instruction of Acoustic consultant /Site Engineer Incharge /Architect. |
| 132 | Providing and laying 8mm thick Nylon Broadloom Carpet of make Shaw or Milliken of approved shade laid above 10mm thick underlay and having 5 to 6mm high tufted loop patternpile with solution dyed non woven synthetic fibre with proper backing having pile density factor of more than 7000 OZ per cubic yard and weight 26 OZ per sq.yard having 9 to 11 tube per inch,class I radiant panel,NBS smoke less than 450,electrostatic propensity is less than 3.5 KV,work should be carried as per drawing with 10 years warranties ,Carpet should adhere to all specification and before installation shade should checked from the Architect,etc.complete as per drawing as directed. |
| 133 | Auditorium Chair : The proposed chair shall have a fully upholstered fixed back seat both using Moulded Polyurethane Foam of special grade & special quality & double weave upholstery material. ' The chair shall be free standing being fixed to the floor by three nos. anchor bolts in the base & coupled together by common armrests. Design shall be such, by choice of its size and section of the structural material used, that the stability of the row of seating, incorporating a number of chairs when coupled together as integrated row is fully ensured.' The shell comprises of the following main components namely:' 1. The main frame proper.' 2. Seat and back proper.' The seat 460X490mm with thickness of 130mm, shall comprise of the plywood support baseplate, the requisite Moulded P.U Foam 3’’ thick with ½ inch walling & requisite upholstery. The support plate shall comprise of 19mm good quality plywood hot moulded and cut to size, finished to be tight closed fit insertion into the cavity formed by the walling of the Moulded P.U Foam.' Fabricate the back cushion to be 34mm P.U.foam of 17mm layer each with extra padding for lower back support. The back & seat will be fully & completely upholstered. The upholstery of both back and seat shall be stitched as wall slip-on covers & one edge of the rare for the back, and bottom one for the seat shall be kept open for slip-on purposes and then zipped ensuring a tight uniform wrinkle free finish all round. The machine stitching of the upholstery shall be done in lock stitch using double needle machine only. ' Each chair shall be supplied with Natural Oak Armrest approx. 10’’ long. Standard grain filling shall be done on the handles after which they will be polished in matt finish of approved tint. The Handles should be atleast 70mm wide.' |
| 134 | Providing & Fixing Observation Window (Control Room window) - 230 x 50 mm sal wood window frame having 12mm thk clear toughned glass on Control room side as per drawing. 12 mm thk clear toughned glass fixed in 6 mm thk 'U' channel rubber gasket lining all round the glass to make air tight. Necessary beading patti of 37.5 x 25 to be fixed all round on the glass from Control room side. Window frame to be melamine polish and have one coat of Anti-teR.mtite paint. All exposed surface have one coat of wool presevative paint including erecting, fixing, levelling, etc., complete. |
| 135 | Providing & Fixing & Shaping 1st quality C.P.Teak or Indian Teak for Door and window Frame 200 x 75 & 150 x 75 mm , 300 X 50 mm thk including making double rebate, as per detail drawing including M.S hold fast in plumbline, and finishing fine surfaces by randha. All internal surfaces have one coat of Anti-termtite paint. All exposed surface have one coat of wood presevative paint including erecting, fixing, levelling, etc work will be carried out as per drg and instruction of acoustic consultant /Engineer & Architect. |
| 136 | 200 X 100 mm |
| 137 | 100 x 75 mm |
| 138 | 300 x 50 mm Observation Window Frame |
| 139 | Providing & fixing Acoustical door for shutter finished both sides with both sides veneer. The door shall be 125mm thick shutter (excluding the wooden reed putty). Door shutter shall be made in Saal wood frame in 75 x 31 and 50 x 35 mm frame as shown in the drg. Frame shall have both side 12 mm thk. commercial Ply on both sides with 4.5 mm thk matching grain veneer from external side only. Polyester wadding of 50 mm thk.1000 gsm density shall be kept between. |
| 140 | SIZE OF DOOR OPENING -1800 x 3000(Ht) |
| 141 | SIZE OF DOOR OPENING - 1500x 2250 (Ht) |
| 142 | Providing & fixing 100 mm thk. Acoustical, 2 hour fire rated door shutter, finished with 4 mm thk. veneer on the inside & 1 mm thk. laminate on outside, complete as per detail dwgs & as directed by Engineer. Door Shutter shall be made up of 2 layers of Sal wood framework, each layer made up of Sal wood framework of 35 X 75 mm wide & required width all around and also intermediate framework 600 mm c/c. polyester wadding of 50 mm thk, 1000 gsm density shall be placed in between each Sal wood framework. Fixing 7 kg/m2 density Tecsound insulation layer in between both frameworks. Fixing 125 x 50 mm 1st class C.P. Teak wood lapping patti on three sides (adjacent to door frame) & 125 x 12 mm thk. fire retardant plywood lapping patti at the bottom. Framework shall be provided with 12mm thk. fire retardant plywood on both sides, finished with 4 mm thk veneer (natural, light coloured such as steam beach, golden cherry, larch, etc.) of approved make and shade on the inside & 1 mm thk wood like matt laminate of approved make & shade on the outside. Door shutter shall have double rebates for fixing into the door frame, with EPDM doorseal in one rebate and intumescent smoke strip in second rebate. Door shutter shall have automatic drop down seal at bottom. Pidilite Terminator Wood Preservative shall be applied to internal surface of all |
| 143 | SIZE OF DOOR OPENING - 1200 X 3000 MM HT( Stage Entry) |
| 144 | SIZE OF DOOR OPENING - 1100 X 3000 MM HT ( Green Room ) |
| 145 | SIZE OF DOOR OPENING - 1050 X 3000 MM HT ( Balcony ) |
| 146 | Providing and Making of 1200 mm wide Catwalk in M.S angle section of 75 x 75x 6mm thk placed at 600mm c/c in shorter span and along the longer spanat 1200mm c/c with necessary support system in 50 x 50mm box sectionplaced vertically at1200mm c/c , support from purlin .Catwalk will have the pipe railing of 50mm dia along with two horizontal member pipes of 25mm dia for saftey. Rate should include 2 coat of red oxide and 1 coat of black pain. Base to be coverd in 25mm thk bison board. as directed complete. |
| 147 | Providing / Making / Fixing podium table in 19 mm thk. commercial ply with veneer facing complete with Melamine polish as shown in the drawing. Table shall have cut out (300 mm dia. or 300 x 300) in teak with Melamine polish or paint finish Size :- 600 x 400 x 1200 mm. |
| 148 | Providing/Making/Supplying table as Mixer table in 19 mm thk. Marine ply with FoR.mtica finishing as per drawing complete. Table shall be made in 19 mm thk ply with sides & top along with small apron. All sides have laminate finishing. table top shall have necessary cut out for Audio Mixer Unit shall be made at site and as per the instruction on site. |
| 149 | Providing/ Making & Supplying Projector Table in 19mm thk fire rated ply with 1.5mm thk laminate finish and with 75 x 37.5mm footrest in saalwood. The table will have drawers made with 19mm fire rated ply as per drawing complete, Table shall be made in 19mm thk fire rated ply with sides & top along with front and drawer line in laminate finish.Including S.S handles, Locks and necessary hardware like sliding channels etc. Internal surfaces shall be finished with two coats of french poilsh etc complete.Work will be carried out as per drg & instruction of Acoustic consultant /Site Engineer Incharge /Architect. Size - 1500 x 750 x 750 mm. |
| 150 | Providing / Fixing exit box in C.P. Teak with 4 mm thk. glass with painted 'EXIT' letters in Red. Size : 450 x 230 x 150 mm depth |
| 151 | Providing & fixing of the 125mm wide ply batten fabricated from 8mm ply fixed on the edge of the step for supporting the step light. Edge of the ply shall be well projected during the construction of the Auditorium step.Work will be carried out as per drg & instruction of Acoustic consultant /Site Engineer Incharge /Architect |
| 152 | Applying 3 coats of Plastic paint of approved make /Asian paint or Nerolac or ICI Dulux. Surface shall be clean and sanding by sand paper & applying one coat paint & putty and again sanding & leveling & two coats of paint till approved & satisfaction to Architect complete with scaffolding, levelling shade colour etc.work will be carried out as per drg & instruction of acoustic consultant /Engineer & Architect. |
| 153 | Providing & making of 75 mm thk trap door with rebate for the A.H.U,machine maintenance. The rebate shall be finished with 'O' rubber lining to make it air tight including hardware hinges towerbolt etc scaffolding & as per instructions and satisfaction of a site engineer / consultant. Trap door detail: 1 layer of 12 mm thk E board both side of G.I frame work with 50 mm thk 1000 gsm density polyester wadding in between frame. E baord to be finsihed with 10 mm thk PET panel |
| 154 | Providing & fixing 2 to 3 mm thk. perforated aluminum sheet on walls and ceiling, screwed to G. I. framework with screws @ 200 c/c in both directions. G.I frame fabricated with 72x32x0.5 floor & ceiling channel at top and bottom edges, 50 x 37.5 x 0.5 stud section at 1220mm c/c vertically, 80 x 26 x 0.5 ceiling section at 400mm c/c horizontally, complete as per manufacturers specifications including polyester wadding of 75 mm thk, 1000 gsm density placed between the framework. Entire framework & polyester wadding shall be covered with welded mesh of G.I 12 mm x 12mm square of 24 guage (as per approved sample), complete at all heights as per detail dwgs or as directed by Engineer. |
| 155 | Supply, Installation, Testing & Commissioning of Main Valance Fabric : Fire retardant velvette fabric 100% (2 times of the finished dimension) gathering as per the approved patern and colour, not less than 300 GSM, duly stitched along with eyelets. Size : 12 x 1.3 Meter (Make: Omphile / Nexgen / Custom) |
| 156 | Supply, Installation, Testing & Commissioning of Main Curtain Fabric : Fire retardant velvette fabric with lining 100% (2 times of the finished dimension) gathering as per the approved patern and colour, not less than 300 GSM, duly stitched along with eyelets. Size : 13 x 4.2 Meter (Make: Omphile / Nexgen / Custom) |
| 157 | Supply, Installation, Testing & Commissioning of Rear Curtain Fabric : Fire retardant cotton fabric 50% gathering for as per the approved patern and colour, not less than 250 GSM, duly stitched along with eyelets. Size : 10 x 4.2 Meter (Make: Omphile / Nexgen / Custom) |
| 158 | Supply, Installation, Testing & Commissioning of Frill Fabric : Fire retardant cotton fabric 50% gathering for as per the approved patern and colour, not less than 250 GSM, duly stitched along with eyelets. Size : 8 x 1.3 Meter (Make: Omphile / Nexgen / Custom) |
| 159 | Supply, Installation, Testing & Commissioning of Wing Fabric : Fire retardant cotton fabric 0% gathering for as per the approved patern and colour, not less than 250 GSM, duly stitched along with eyelets. Size : 4.2 x 3.1 Meter |
| 160 | Dismantling RCC, Brickwork, Doors/windows, Steel, trusses, plinths, Timber, existing plumbing fittings, pipes etc from existing Buildings such as OLD Guest House building as directed and carefuly stacking the salvaged items including labour, material, cranes,tools and plants, fuel etc.The work shall be carried out as per directions of Engineer IN Charge carefully.Rate shall be inclusive of hiring of cranes and other machineries tools and plants etc. required for dismantling, Note: Work shall be carried out with utmost care to avoid any damage to the existing property. The removal of Debris is to be part of this item and the site has to be cleared on a daily basis. The debris should not be dumped in landfills or illigally dumped and must be possibly reused on site or offsite for filling, levelling purposes. Contractor is advised to visit the site of work to assess the quantum of work involved as no additional item of dismantling shall be paid separately. Item to include shifting of usable furniture, dismantling roads, asphalt areas, removal of street lamps handed over to PWD, removal of all plumbing, fixtures etc, and making the site bare and ready for excavation works. |
| 161 | Providing and fixing double scaffolding system (cup lock type) on the exterior side of building/structure, including additional rows of scaffolding in stepped manner as per requirement of site, made with 40mm dia M.S. tube, placed 1.5 metre centre to centre, horizontal & vertical tubes joint with cup & lock system with M.S. Tubes, M.S. tube challis, M.S. clamps and staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for execution of work of cleaning and/ or pointing and/ or applying chemical and removing it thereafter. The scaffolding system shall be stiffened with bracings, runners, connecting with the building etc, wherever required, if feasible, for inspection of work at required locations with essential safety features for the workmen etc., complete as per directions and approval of Engineer-in-charge. Note:- (1) The elevational area of the scaffolding shall be measured for payment purpose. (2) The payment will be made once only for execution of all items for such works. |
| 162 | Providing and fixing Jute Kantan (Tarat) screen to the scaffold-ing for external guniting as directed including removing the same after the work is over etc. complete. |
| 163 | Providing and fixing chicken mesh of 22 gauge, with about 30 cm. width at the junction of R.C.C members and brick work, of approved quality including fixing mesh in position by necessary drilling in concrete /B.B.masonry and or tying by binding wire etc. complete. |
| 164 | Providing rough cast cement plaster externally in two coats to concrete, brick or stone masonry surfaces in all positions with base coat of 12 to 15 mm thick in C.M. 1:4 and rough cast treatment 12mm thick in proportion 1:1 1/2:3 including scaffolding and fourteen days curing complete. |
| 165 | Providing & laying grey basalt stone of size 150mm x 200mm in cement mortar 1:6 in external walls of plinth including bailing out water manually etc. complete. |
| 166 | Providing sills of polished Kadappa stone 25mm to 30mm thick, on a bed of 1:4 cement mortar including cement float, filling joints with slurry, curing polishing and cleaning etc. complete. (Flooring & Skirting) |
| 167 | Providing and laying vitrified stone effect finish tiles having size size 590 mm to 605 mm x 590 mm to 605 mm of 8 to 10 mm thickness and confirming to IS. 15622-2006 ( group Bla) of approved make, shade and pattern for dado and skirting in required position fixed in 1:4 cement mortar including neat cement float, filling joints, curing and clearing etc. complete. (flooring & dado) |
| 168 | Providing and fixing 30 mm thk scratch proof Engineered wooden flooring and skirting in deep walnut finish / teak finish as per sample approved by the Site in Charge and company specifications. Item to include providing and fixing skirting matching to the flooring. |
| 169 | Providing and applying two coats Apex Ultima Pura nature AntiPollution Or equivalent approved brand, paint should decomposes organic substances and inorganic gases (NOx,VOC’s,CO,SOx,formaldehydes,etc.) in presence of natural or artificial light. It contains Graphene and nano particles of titanium oxide. and Absorbs CO2 (4.8Kilogram/15l). plaster crack should be filled by Acrylic base Crack seal / Textured Crack filler, Paint has to applied on one coat of Apex Ultima Pura nature Anti- Pollution Primer or Equivalent. Warranty Should be given by the Manufaturer. The work should be done by the Manufacturer Recommended applicator and he should be able to furnish stage wise on site technical reports from the concerned company technologist. |
| 170 | Providing and applying Texture plaster with finishing with texture material of approved make in 3 to 4 millimeter thickness on previously plastered surface, including Plaster Groove 6mm thickness or Tape Grooves 35 to 45 mm thickness or as required, in all position including preparing the surface, scaffolding etc. complete. |
| 171 | Reception table of size 6'0\\" x 2'0\\" and 2'6\\" - Providing and supplying in position table of different sizes made out of 19 mm thick marine plywood of the requisite manufacture viz Anchor/Century/ Kenwood/ Duro or equivalent generally confirming to I.S.303/1.S.710-1980 top verticle sides and 6mm marine plywood back of the requisite manufacturer viz anchor / Century/ Kenwood/ Duro or equivalent generally confirming to I.S.303/I.S.710-1980 back including one drawer made out of 12mm thick marine ply sides and 6mm thick marine ply bottom with necessary lipping on external sides and shutter of 19 mm thk. marine ply and foot rest out of 40 x 75mm (finished dimension) CPTW and M.S. powder coated key board tray etc. as per drawings and instructions. The external side will be finished in laminate and top shall be finished with grooves and all internal surfaces of table and drawer shall be internally with two coats of french polish with antitermite treatment. |
| 172 | Supply and installation of cubicles of width and depth as per Athena Lite-SS Series Cubicles-Std Sizes (WxDxH): 900mm x 1550mm x 2105mm, (Height is including 100mm gap from bottom, Door Width -600mm specifications / sitedrawings). Cubicle height to be 2105mm. Made from solid grade compact high pressure laminate as per IS:2046 and EN-438 manufactured under high specific pressure >5MPa and temperature>120°C, All doors will be of single colour and made of 12mm thick Merino HPL compact panel. The doors will have chamfered edges. Each door will be supported by 3 stainless steel made hinges affixed to the pilasters. Size of panels to be as per drawing. HARDWARE & ACCESSORIES are H shaped (Top) head frame structure made of extruded Aluminium grade 6063 T5-50 micron epoxy powder coated for surface protection, Size to be 125 x 70 x 5T. Corner joinery section, Size to be 40x16.5x1.8T. U Channel Wall joinery section, Size to be 22x16x1.6T. Door stopper section, Size to be 21x12.5x1.6T. Spring loaded Butt Hinges made from Stainless steel grade 304. Surface finish to be matt type. Covers to be lacor coated.etc complete. |
| 173 | Providing and fixing 600mm deep prepolished Natural Stone/Quartz Stone counter cantilevered from wall with concealed M.S. frame below having upto 450mm high Natural Stone/Quartz Stone fascia in front, at the edge, machine polishing, sanding of edges etc., complete with cleaning and protection with POP and plastic sheets during work. The counter shall be sealed with a marble floor sealant that does not have a sheen, leaves a natural look, and is solvent based with a guarantee of 5 years, of Aquamix or equivalent make, as per company specifications. |
| 174 | Providing and Fixing Mirrors of approved Indian quality Copper Plated with 3/8\\" thick Ply wood backing in the Masonary etc.complete |
| 175 | Providing and fixing 50mm thick flushed doubled leaved door using well seasoned CCTW wood inclusive of any brass inlay work. The rate for the door shall include adhesive and all the hardware like heavyduty Brass holdfasts, nails, screws, butt hinges, handles, lock, concealed door closer, door stopper etc. required to complete the item. All the exposed hardware shall be brass finish with a protective lackre coat. Contractor to do complete finishing of the shutter inclusive of primer and paint or melamine polish as approved by the Architect. |
| 176 | Providing and fixing 40mm thk solid single shutter wooden door using well seasoned CCTW wood. The design and details to be as per instructed by the Architect including all necessary fitting Brass hardware like screws, nails, concealed hinges, tower bolts, handles, of the same design, size and weight, etc. complete. All hardware to be concealed. Item to include complete finishing of the shutter in melamine polished look as per manufacturers specificfations as per colour approved by the Architect. All the exposed hardware shall be brass finish with a protective lackre coat. The area of the shutter includes the entire opening with all the leaves. |
| 177 | Providing and fixing solid core flush door shutter in single leaf 32 mm thick decorative type of exterior grade as per detailed drawings approved face veneers 3 mm thick on both faces or as directed, all necessary beads, mouldings and lipping, wrought iron hold fasts, chromium plated fixtures and fastenings, with brass mortise lock, chromium plated handles on both sides, and finishing with French Polish etc. complete |
| 178 | Providing and fixing in position anodised (as per IS1868/1982) Aluminium fixed staggered (Z Type) Ventilator with aluminium rectangular pipe 63mm x 38.10mm x 1.22mm at weight 0.650 Kilogram/One Running Metre, Aluminium angle of size 15mm x 15mm x 1mm, aluminium channel of 9mm sizes, S.S.mosquito net of 304 Grade, 4mm thick float glass as per detailed drawing and as directed by Engineer in charge etc. complete. |
| 179 | Providing and fixing CCTW sliding folding FULL louvered doors/windows with T.W frame sliding and folding shutters of size 75mm x 40mm thick having CCTW fully openable louvers as instructed by the Architect including all necessary fitting brass hardware like screws, nails, concealed hinges, tower bolts, handles and inclusive of track cost of the same design, size and weight, etc. complete. Item to also include making all the mouldings and design of the panels with all beading patti as per size etc., Item to include complete finishing of the shutter inclusive of primer and paint / melamine polish as approved by the Architect. Mode of Measurement: Area of the door/window which is changed or made new in the entire door shall only be paid. The area of the shutter includes the entire opening with all the leaves. |
| 180 | Providing and fixing CCTW shutter of size 75mm x 40 mm thick with well seasoned CCTW double leaves partly fixed / openable louvered shutters for doors as instructed by the Architect including all necessary fitting brass hardware like screws, nails, hinges, tower bolts, handles, of the same design, size and weight, etc. complete. Item to also include making all the mouldings and design of the panels with all beading patti as per size etc., Item to include complete finishing of the shutter inclusive of primer and paint / melamine polish with PU coating as approved by the Architect. Mode of Measurement: Area of the door which is changed or made new in the entire door shall only be paid. The area of the shutter includes the entire opening with all the leaves. |
| 181 | Providing and fixing in position powder coated aluminium louvered windows / ventilator of various sizes with powder coating as per detailed drawing and specifications including aluminium frames 80x38mm x 1.22mm box type, 5mm thick sheet glass louvers, of approved quality etc. complete. |
| 182 | Supplying and fixing in position Aluminium four track sliding windows with outer frame made from section of overall size 122mm x 45mm, bottom section with drain section track weighing 1.83 Kilogram per metre and top and side section of size 122 x 31.75mm weighing 1.15 Kilogram per One Running Metre with shutter sections made of 18mm x 40mm size having average weight of 0.6 Kilogram per One Running Metre (or as required size with change in proportionate weight, with 6mm float glass in three equal panels and alluminium coated stainless steel mosquito net in one (2/3 of opening panel fixed with new neo prene gasket, shutters to be provided with nylon encased stainless steel rollers, necessary locks and handles complete. - Powder Coated |
| 183 | Providing and laying PERFORATED / DESIGNER TERRACOTTA TILE SCREEN using 50X50mm & 30x30mm MS frames, flats, etc and clad with 150x150x25/30mm terracotta perforated tile as specified below (Machine cut) of an approved quality and size for facade cladding as per colour, texture and finish approved by the Architect from leading natural stone suppliers.Item inlcudes fixing on a bed of 1:6 C.M. including cement float, striking joints, pointing in cement mortar 1:3 curing and cleaning etc. complete proportion, cement float, machine cutting, dressing, leveling, jointing, filling the joints with neat cement slurry or with required pigment at site, curing, finishing, etc complete as directed by Engineer In Charge. Item to include provision of double shutter door within screen same to be blended within screen using necessary hinges, locking system etc.Item to include procuring the lot from a vendor who has access to the quarry in order to get large material with consistent finish. Item to include all transportation, taxes including fixing. |
| 184 | Supplying and fixing - Single Bed Providing by making & supplying of single Bed for clinic size of 6'6\\" x 3'0\\" in size & 100 cm height made height of 19mm Marine ply for sides plates & 12mm thk for Mattress Base & all Marine Ply of the requisite manufactur viz equipment generalely conforming to IS.303/IS. 710-1980 & finishing with 1.5 mm thk laminate of approved make & pattern on all visible external sides including necessary lipping T.W.molding with internaly plywood sarface should finished by french polishing etc complete. |
| 185 | Supplying and fixing - the BEDSIDE NIGHT STAND- of 0.56m x 0.53m upto a height of 550mm Providing and supplying in position table of different sizes made out of 19 mm thick marine plywood of the requisite manufacture viz Anchor/Century/ Kenwood/ Duro or equivalent generally confirming to I.S.303/1.S.710-1980 top verticle sides and 6mm marine plywood back of the requisite manufacturer viz anchor / Century/ Kenwood/ Duro or equivalent generally confirming to I.S.303/I.S.710-1980 back including one drawer made out of 12mm thick marine ply sides and 6mm thick marine ply bottom with necessary lipping on external sides and shutter of 19 mm thk. marine ply and foot rest out of 40 x 75mm (finished dimension) CPTW and M.S. powder coated key board tray etc. as per drawings and instructions. The external side will be finished in laminate and top shall be finished with grooves and all internal surfaces of table and drawer shall be internally with two coats of french polish with antitermite treatment. |
| 186 | Supplying and fixing- rectangular study table upto 600 mm deep and 780 mm height Table top of length 1.3m to be built in hardwood, Providing and supplying in position table of different sizes made out of 19 mm thick marine plywood of the requisite manufacture viz Anchor/Century/ Kenwood/ Duro or equivalent generally confirming to I.S.303/1.S.710-1980 top verticle sides and 6mm marine plywood back of the requisite manufacturer viz anchor / Century/ Kenwood/ Duro or equivalent generally confirming to I.S.303/I.S.710-1980 back including one drawer made out of 12mm thick marine ply sides and 6mm thick marine ply bottom with necessary lipping on external sides and shutter of 19 mm thk. marine ply and foot rest out of 40 x 75mm (finished dimension) CPTW and M.S. powder coated key board tray etc. as per drawings and instructions. The external side will be finished in laminate and top shall be finished with grooves and all internal surfaces of table and drawer shall be internally with two coats of french polish with antitermite treatment. |
| 187 | Visitors Chairs/Fix Chair : The seat and back are made up of 1.2 cm. thick hot-pressed plywood, upholstered with fabric upholstery covers and moulded Polyurethane foam. The back foam is designed with contoured lumbar support for extra comfort. The seat has extra thick foam on front edge to give comfort to popliteal area. BACK SIZE:47.5 cm. (W) x 58.0cm. (H)SEAT SIZE: 47.0 cm. (W) x 48.0 cm. (D) POLYURETHANE FOAM: The Polyurethane foam is moulded with density = 45 +/-2 kg/m3 and Hardness = 20 +/- 2 on Hampden machine at 25% compression. 3) ARMRESTS: The one-piece armrests are injection moulded from black Copolymer Polypropylene as per order. (Material supplied should be standard company) |
| 188 | Supplying Dinning table set of 4: Providing a 1000mm x1000mmx 750mm wardrobe with hardwood built with indian teak wood, 4 decorative T.W carved legs as shown in the image. All extrernal surfaces such as sides to be in teakwood. All internal and external surfaces shall be finished with approved french polish. Item to include spray coating all the surfaces with approved anti termite solution including providing 10 year guarantee for the same as directed by the Architect or Engineer in Charge. |
| 189 | Supplying Dinning table set of 6: Providing a 1500mm x900mmx 750mm wardrobe with hardwood built with indian teak wood, 4 decorative T.W carved legs as shown in the image. All extrernal surfaces such as sides to be in teakwood. All internal and external surfaces shall be finished with approved french polish. Item to include spray coating all the surfaces with approved anti termite solution including providing 10 year guarantee for the same as directed by the Architect or Engineer in Charge. |
| 190 | Providing and supplying Chair without arm for lecture/seminar hall having a plastic moulded seat in and a carved wooden legs as per design approved by the Architect. All exposed wooden surfaces shall be finished with french polish. |
| 191 | Providing cushion fillers of polyfill filling of approved brand of equivalent as suggested by the architect - 18\\" x 12\\" |
| 192 | Box type Cotton Mattresses size Size 182.9 x 91.4 x 10.2 cm Dimension (Length x Width) 2.5ft * 6ft Thickness 5inch of 10 Kg. cotton |
| 193 | Providing Thermal Bond soft duvet made from Filling : ‘Wonder Fill’ 250 GSM Feather Touch Thermal-Bonded Superior Quality 100 % Cotton Fabric with Fabric Count : 40s x 40s. ( size - 100\\" x 96\\" )of approved brand of equivalent. |
| 194 | Colour Single Bed Sheets (60'' x 90'') (Bombay Deying) Pillow cover (18\\" x 12\\") included with all the Bed sheet & pillow covers. |
| 195 | Providing and laying Cast in situ / Ready Mix cement concrete in M-25 of trap / granite / quartzite / gneiss metal for R.C.C. pardi of required thickness including steel centering, formwork, cover blocks, laying / pumping, compacting, curing, finishing and roughening them if special finish is to be provided and curing complete. (Excluding reinforcement, including cover block). (Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer / concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) |
| 196 | Providing and laying Cast in situ / Ready Mix cemen tconcrete in M-25 of trap / quartzite / granite / gneiss metal for R.C.C. Waist slab, and steps of staircases as per detailed design and drawings or as directed including steel centering, formwork, steel props, laying / pumping, compaction, finishing uneven and honeycombed surface with C.M. 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening the surface if special finish is to be provided and curing etc. complete. (Excluding reinforcement, including cover block). (Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer / concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) |
| 197 | Providing and laying Castinsitu / Ready Mix cement concrete M-25 of trap / granite / quartzite / gneiss metal for R.C.C. chajja as per detailed design and drawings including steel centering, formwork, cover blocks, laying / pumping, compacting and roughening the surface if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer / concrete Batch mix plant (Pan mixer)etc. complete. With fine aggregate (Crushed sand VSI Grade) |
| 198 | Gently cleaning the surface of stone masonry and piers with specialized water misting techniques employing air using a fine nozzle sprinkling system calibrated to spray fine mist along the stone surface without over wetting followed up by gentle brushing with soft nylon brushes and removing dirt, dust, birddropping, grease, oil, algae, fungus, monkey beats, vegetable growth etc. as specified. Gentle surface cleaning may include using water misting and mild pH balanced surfactants as specified for indicated area to remove the surface dirt, grit accretions by means of water misting and cleaning etc. complete as directed by the Engineer in Charge. (The rate is inclusiveof all materials & labours involved except scaffolding). |
| 199 | Dismantling stone masonry in lime or cement mortar including stacking the materials as directed with all leads, lifts etc. |
| 200 | Removing lime or lean cement concrete including stacking the spoils as directed with all leads, lifts etc, complete. |
| 201 | Providing and laying Cast in situ / Ready Mix cement concrete in M-20 of trap / granite / quartzite / gneiss metal for R.C.C. coping to plinth or parapet and sill of doors and windows moulded as per detailed drawings or chamfered as approved by the Engineer including steel centering, formwork, cover blocks, laying / pumping, compacting, curing, finishing and roughening them if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer / concrete Batch mix plant (Pan mixer)etc. complete. With fine aggregate (Crushedsand VSI Grade) |
| 202 | Providing uncoursed rubble masonry of trap / granite / quartzite / gneiss stones in cement mortar 1:6 in super structure including racking out joints when plastering is to be done / striking joints when no plastering is to be done on inside watering and scaffolding etc. complete. |
| 203 | Providing tuck pointing with cement mortar 1:3 for stone / Brick masonry including scaffolding and curing etc. complete. |
| 204 | Providing and fixing Introductory signage (S-E-01) Horizontal made up of 500 mm high (1\\" thick) individual cut Stainless steel letters SS 304 grade signage in two text layers one above the other and third layer made up of 200mm high stainless steel SS 304 cut letters (1\\" thk) as shown in the drawing, anchored into the ground or fixed in the wall. The letters to be anchored to each other using 5mm thk SS plate welded. All the three layered text to be anchored below ground 650mm deep cement concrete bed 1:2:4 (1 Cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) inclusive of excavation, centering, shuttering, curing and finishing using 20mm dia SS anchor rods and making sure of all necessary means / hardware required to anchor the signage to the ground / wall. (Total height of signage to add upto human scale / height). Including all the Taxes |
| 205 | Providing and fixing Introductory signage (S-E-02) vertical made up of 250 mm high (1\\" thick) individual cut Stainless steel letters SS 304 grade signage anchored into the ground or fixed in the wall using 80mm dia SS 304 pole. The letters to be anchored to each other using 5mm thk SS plate welded. The signage to be anchored below ground 650mm deep cement concrete bed 1:2:4 (1 Cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) inclusive of excavation, centering, shuttering, curing and finishing using 20mm dia SS anchor rods and making sure of all necessary means to anchor the signage to the ground / wall. (Total height of signage to add upto human scale / height) |
| 206 | Providing and fixing Introductory signage (S-E-03) of 1850 mm height and 75 mm in depth using 75mm x 75mm thk MS epoxy coated sections for the framework, cladded with precoated 4mm thk Aluminium sheets bent on the edges to give a seamless finish. Item to include printing on Aluminium as well as laser cutting for letters and other graphics as mentioned in as many colours as required. For the backlit portion of the signage, 5 mm acrylic sheet to be used and fitted with epoxy coated angle cleats as shown in the drawing.The entire signage to be fitted to the ground using 6mm thk MS epoxy coated base plate and anchored below ground upto depth of 750mm using cement concrete bed 1:2:4 (1 Cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) inclusive of excavation, centering, shuttering, curing and finishing using 20mm dia SS anchor rods and making sure of all necessary means to anchor the signage to the ground / wall. The signage to also have panel doors at the back to maintenance inclusive of all hinges and locking mechanism. Including all the Taxes |
| 207 | Providing and fixing Information signage (S-F-01) of total height of 1300 mm x 600mm x 40mm thk using 35mm x 35mm thk MS epoxy coated sections for the framework, cladded with 4mm thk SS brushed steel cladding bent on the edges to give a seamless finish. Item to include printing on 2mm thk Aluminium sheet fixed to top panel covering all three sides in as many colours as required. The entire signage to be fitted to the ground using 6mm thk MS epoxy coated base plate and anchored below ground upto depth of 750mm using cement concrete bed 1:2:4 (1 Cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) inclusive of excavation, centering, shuttering, curing and finishing using 20mm dia SS anchor rods and making sure of all necessary means to anchor the signage to the ground / wall. |
| 208 | Providing and fixing Cautionary signage (S-F-03) of total height of 800 mm x 200mm x 20mm thk SOLID SINGLE PIECE Precoated Aluminum signage. Item to include printing on the above signage using transperent Vinyl stickers in as many colours as required. The entire signage to be flushed to the ground using 6mm thk MS epoxy coated base plate and anchored below ground upto depth of 750mm using cement concrete bed 1:2:4 (1 Cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) inclusive of excavation, centering, shuttering, curing and finishing using 20mm dia SS anchor rods and making sure of all necessary means to anchor the signage to the ground / wall. |
| 209 | Providing and fixing Directional signage (S-G-02) of total height of 2400 mm x 300mm wide x 30mm thk using 4mm thk MS epoxy coated sections for the framework, cladded with precoated 2mm thk Aluminium sheets bent on the edges to give a seamless finish. Item to include printing on Aluminium as well as laser cutting for letters and other graphics as mentioned in as many colours as required. For the backlit portion of the signage, 5 mm acrylic sheet to be used and fitted with epoxy coated angle cleats as shown in the drawing.The entire signage to be fitted to the ground using 6mm thk MS epoxy coated base plate and anchored below ground upto depth of 750mm using cement concrete bed 1:2:4 (1 Cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) inclusive of excavation, centering, shuttering, curing and finishing using 15mm dia SS anchor rods / J bolts and making sure of all necessary means to anchor the signage to the ground / wall. The signage to also have a panel door at the back for maintenance inclusive of all hinges and locking mechanism. Including all the Taxes |
| 210 | Providing and fixing Directional signage (S-G-01) of total height of 2400mm x 800mm wide x 100mm thk divided into 3 parts (each part of 800mm x 800mm size) using 30mm x 30mm thk MS epoxy coated sections for the framework, cladded with precoated 2mm thk Aluminium sheets bent on the edges to give a seamless finish as shown in the drawings. The MS framework to be supported on a central MS section on 100mm x 100mm thk. Item to include printing on Aluminium for letters and other graphics as mentioned in as many colours as required. The entire signage to be fitted to the ground using 6mm thk MS epoxy coated base plate and anchored below ground upto depth of 750mm using cement concrete bed 1:2:4 (1 Cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) inclusive of excavation, centering, shuttering, curing and finishing using 20mm dia SS anchor rods / J hooks and making sure of all necessary means to anchor the signage to the ground / wall. Including all the Taxes |
| 211 | Providing and fixing Directional signage (S-G-04) of size 400mm x 500mm fixed on the ground and as seen both ways on elevation and in plan made of single precoated 4mm thk anodised Aluminium sheets cut in the shape of an arrow to give a seamless finish as shown in the drawings. Item to include printing on Aluminium for letters and other graphics as mentioned in as many colours as required. The entire signage to be fitted to the ground using 6mm SS anchor hooks and anchored below ground using cement concrete bed 1:2:4 (1 Cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) inclusive of excavation, centering, shuttering, curing and finishing and making sure of all necessary means to anchor the signage to the ground / wall. Including all the Taxes |
| 212 | Providing and fixing TOILET signage in SS 304 2 mm plates of size 250 x 600 mm with lettering etched on burnished finish steel panel screwed to the walls with SS brushed steel bolts.The graphics shall be cut coloured acrylic sheet and text pasted on the SS plate as directed by the architect.Rate to be inclusive providing, fixing and installation etc. complete. Including all the Taxes |
| 213 | Providing and fixing TOILET signage in burnished SS 304 2 mm plates of size 210 x 210 mm painted with lettering etched on brush finished steel panel screwed to the internal doors with SS brushed steel bolts.The lettering may be stenciled or etched as directed by the architect. Rate to be inclusive providing, fixing and installation etc. complete. Including all the Taxes |
| 214 | Providing and fixing MS cut letters signage 300 mm high anchored into the ground or fixed in the wall with anchor fastners coated with anti rust paint. The letters to be painted with 2 coats of epoxy paint and 3 coats enamel paint as approved by the Architect. Including all the Taxes |
| 215 | Providing and fixing 300 mm high individual cut Stainless steel letters SS 304 grade signage anchored into the ground or fixed in the wall with anchor fastners coated with anti rust paint. Including all the Taxes |
| 216 | Providing and fixing 100 mm high individual cut Stainless steel letters SS 304 grade signage anchored into the ground or fixed in the wall with anchor fastners coated with anti rust paint. Including all the Taxes |
| 217 | Fabrication and installation of Cast Iron gates of approved design& drawing in cast iron of min 12mm gauge weight Not less than 70 kgs/m2.& having pre cast base plate of thickness 20mm with provision of grouting for foundation bolts. All cast iron, members painted with anti-corrosion primer and coated with two coats of polyurethane coatingand painted in glossy black colour as specified. All vertical upstands to be embedded in concrete block as shown in drawings. Bolts andnuts to be welded after fixing. Rate to be inclusive of base grouting,providing, fixing, nuts, bolts, welding, painting etc complete. |
| 218 | Fabrication and fixing of Cast Iron grill of approved design & drawing in cast iron of min 10mm gauge weight Not less than 40kgs/m2 & having pre cast base plate of thickness 10mm with provision of grouting for bolts. All cast iron, members painted with anti-corrosion primer and coated with two coats of polyurethane coatingand painted in glossy black colour as specified. All vertical upstands to be embedded in concrete block as shown in drawings. Bolts andnuts to be welded after fixing. Rate to be inclusive of base grouting,providing, fixing, nuts, bolts, welding, painting etc complete. |
| 219 | Providing and fixing 1800mm x 450mm x 500mm solid stone benches of solid Polished Steel Grey Granite stone as per the design given by the Architect, complete with drip moulds. Item to include, grooves as per design and having offset of 50mm on either side of bench at the base of malad stone with adequate bearing below ground for anchoring. The bench to also have logo etched on the seat by CNC cutting. item to include making a sample for approval , to 1:1 scale for the Architect. |
| 220 | MS Planter - Providing & laying in desired location MS planters of welded together with 2mm gauge sheets to be made, the bottom sheet to be made with perforated MS sheet to allow the passage (drain pipe) of excess water. The box to be interlockable and removable for maintenance purposes. Item to include fixing freestanding framework inside the planter at the bottom. Rate to include samples to be shown to Architect for approval. |
| 221 | 1.2x1.2mx0.45m |
| 222 | 1mx2mx0.45m |
| 223 | Fabrication and installation of Cast iron bollards with ear hooks as per approved design. The bollard shall be 1046 mm high with a dia of 160 mm on top and 200mm on below in cast iron of min 12mm gauge weight not less than 70 kgs.& having pre cast base plate of thickness 20mm with provision of grouting for foundation bolts. All cast iron, members painted with anti-corrosion primer and coated with two coats of polyurethane coating and painted in glossy colour as specified. All vertical upstands to be embedded in concrete block as shown in drawings. Bolts and nuts to be welded after fixing. Rate to be inclusive of base grouting, providing, fixing, nuts, bolts, welding, painting etc. |
| 224 | Providing & fixing SS 316 heavy weight Chain of 4 feet long and 8mm rod thickness with snap hook for connection to the bollard. The appox. weight of chain would be 4 to 5kgs. |
| 225 | Providing and fixing heavy duty concrete Basalt paving blocks of 100 x 100mm having a strength of 300 Kilogram / Sq.cm. of approved quality and shape on a bed of crushed sand of 25 to 30mm thick including skirting joints and cleaning etc. complete. |
| 226 | Excavation for planting lawn/ shrub/ flower bed/ hedges/ edges/ canna bed in earth, soil of all types, soft murum, including removing the excavated material up to a distance of 50 mtrs. for a depth of 30 cms. |
| 227 | Supplying on site fresh Garden soil (free from stones rubbish like dried grass roots, other such materials) for excavation area of depth of 30 cms. (consolidated thickness). |
| 228 | Supplying on site well decomposed Farmyard Manure for excavation area of depth of 30 cms. (consolidated thickness) |
| 229 | Filling fresh garden soil / silt & manure in excavated area of depth 30cms. (1/10 of unskilled labour) |
| 230 | Mixing garden soil/silt & manure thoroughly well, watering previous night. Planting required plant species, lawn grass as directed etc. complete for required depth 30 cms. for planting lawn/ shrub/ flower bed/ hedges/ edges/ canna bed/ ground cover. (1/10 of semiskilled labour) |
| 231 | Providing on site required variety of Flowering Shrubs (Well Developed ,Fresh, Healthy half in bloom, free from pest, weeds /diesease etc.) 30 cms. apart c/c.Name:- Plumeria Alba; Bag Size 18 '' x 18 '', Height - 240cm to 270cm |
| 232 | Providing on site required variety of Flowering Shrubs (Well Developed ,Fresh, Healthy half in bloom, free from pest, weeds /diesease etc.) 30 cms. apart c/c.Name:- Plumeria Rubra; Bag Size 18 '' x 18 '', Height - 240cm to 270cm |
| 233 | Providing on site required variety of Flowering Shrubs (Well Developed ,Fresh, Healthy half in bloom, free from pest, weeds /diesease etc.) 30 cms. apart c/c. Name:- Mogara/Jasminum;Bag Size 9 '' x 11 '', Height - 20 cm to 45cm |
| 234 | Providing on site required variety of Flowering Shrubs (Well Developed ,Fresh, Healthy half in bloom, free from pest, weeds /diesease etc.) 30 cms. apart c/c. Name:- Murraya / Kamini ;Bag Size 9 '' x 11 '', Height - 20 cm to 45cm |
| 235 | Providing on site required variety of Flowering Shrubs (Well Developed ,Fresh, Healthy half in bloom, free from pest, weeds /diesease etc.) 30 cms. apart c/c. Name:- Gardenia ;Bag Size 8 '' x 10 '', Height - 45 cm to 60cm |
| 236 | Providing on site required variety of Flowering Shrubs (Well Developed ,Fresh, Healthy half in bloom, free from pest, weeds /diesease etc.) 30 cms. apart c/c. Name:- Ficus Benjamina ;Bag Size 8 '' x 10 '' Height - 30 cm to 60cm |
| 237 | Providing on site required variety of Flowering Shrubs (Well Developed ,Fresh, Healthy half in bloom, free from pest, weeds /diesease etc.) 30 cms. apart c/c.Name:- Pentas ;Bag - Size 6\\", Height - 20 cm to 30cm |
| 238 | Providing on site required variety of Flowering Shrubs (Well Developed ,Fresh, Healthy half in bloom, free from pest, weeds /diesease etc.) 30 cms. apart c/c.Name:- Allamanda ;Bag - Size 10\\" x 10\\", Height - 15 cm to 30cm |
| 239 | Providing on site required variety of Flowering Shrubs (Well Developed ,Fresh, Healthy half in bloom, free from pest, weeds /diesease etc.) 30 cms. apart c/c.Name:- Jatropha ;Bag - Size 8\\" x 10\\", Height - 45 cm to 60cm |
| 240 | Providing on site well established (free from weeds /disease etc.) ready to fix lawn turf in slabs/ rolls of required variety as directed. |
| 241 | Marble Gravel - Loose fill Paving-Providing and laying and Loose Till paving of grey/ white / black marble round gravel / chips as approved by the Architect and ramming and compacting till the top of the edging in a layer 3\\" thick. |
| 242 | Providing second class Burnt Brick masonry with conventional / I.S. type bricks in cement mortar 1:4 in half brick thick wall including mild steel longitudinal reinforcement of 2 bars of 6mm diameter / 2 hoop iron strips 25mm X 1.6mm placed at every third course, properly bent and bonded at ends scaffolding, racking out joints and watering etc.complete. |
| 243 | Providing internal/external cement plaster 12mm thick in single coat in cement mortar 1:5 without neeru finish to concrete or brick surfaces, in all positions including scaffolding and curing etc. complete |
| 244 | Providing and fixing basant beton paving tiles or similar brand of approved quality and type to match the proposed landscape paving on site as directed by the Architect in charge. Item to include cutting the stone as per the sizes of the existing covers, including providing the necessary finishing etc. complete. |
| 245 | Providing and laying Cast in situ/Ready Mix cement concrete M-25 of trap / granite/quartzite/ gneiss metal for R.C.C. work in foundations like raft, strip foundations, grillage and footings of R.C.C. columns and steel stanchions etc. including bailing out water, Steel centering, formwork ,cover blocks, laying/pumping, compaction and curing roughening the surface if special finish is to be provided (Excluding reinforcement and structural steel) etc. complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) |
| 246 | Providing and laying Cast in situ/Ready Mix cement concrete in M-25 of trap/ granite/ quartzite/ gneiss metal for R.C.C. beams and lintels as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks, laying/pumping, compactionand roughening the surface if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) |
| 247 | Providing and laying Cast in situ/Ready Mix cement concrete M-25 of trap / granite /quartzite/ gneiss metal for R.C.C. columns as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) |
| 248 | Providing and fixing Country cut teakwood windows / ventilators with double leaf panelled shutters 25mm thick without ventilators as per detailed drawing including stainless steel fixtures and fastenings and finishing the wood work with oil painting 3 coats etc. complete. |
| 249 | Providing and fixing Mangalore tiled roofing with class 'AA' tiles including securing the last course of tiles near the eaves with steel flat 40 mm x 3 mm and 1.22 mm wire fixing country teak wood sloping battens of 25 x 12 mm teak wood horizontal battens of 50mm x 25mm over the slopping battens, all iron work and coal tarring the battens etc. complete (Excluding ridge and hip tiles). |
| 250 | Providing and fixing Mangalore tile ridge and hip tiles of class 'AA' including scaffolding if necessary, pointing with coloured cement mortar and curing etc. complete. |
| 251 | Providing and fixing Indian teak wood plank ceiling 20 mm thick plain underside tongued and grooved including iron screws, scaffolding, if necessary, including one primer coat on under side and one coat of coal tar on upper side etc. complete. |
| 252 | Providing and fixing on walls/ ceiling/ floor 15 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete. |
| 253 | Providing and fixing on walls/ceiling/floor 20 mm dia. CPVC pipe with necessary fittings,remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete. |
| 254 | Providing and fixing on walls/ ceiling/ floor 25 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc.complete. |
| 255 | Providing and fixing on walls/ ceiling/ floor 32 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc.complete. |
| 256 | Providing and fixing on walls/ ceiling/ floor 40 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc.complete. |
| 257 | Providing and fixing on walls/ ceiling/ floor 50 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc.complete. |
| 258 | Providing, fixing and testing heavy quality gun metal or brass ball valve with screwed ends 20kgm class on GI or copper pipe lines. (Leader/ZOLOTO make) 15 mm (1/2\\") dia. |
| 259 | Providing, fixing and testing heavy quality gun metal or brass ball valve with screwed ends 20kgm class on GI or copper pipe lines. (Leader/ZOLOTO make) 20 mm (3/4\\") dia. |
| 260 | Providing, fixing and testing heavy quality gun metal or brass ball valve with screwed ends 20kgm class on GI or copper pipe lines. (Leader/ZOLOTO make) 25 mm (1\\") dia. |
| 261 | Providing and fixing white european type wall-hung, of size 360mm x 360mm x 575mm with flush valve of approved make including soil pipe, vent pipe upto outside face of wall, 100mm dia C.I. plug bend inlet pipe all fittings,cutting & making good walls, floors etc as directed by Engineer in charge. |
| 262 | Providing and fixing Oval Type Under Counter Wash Hand Basin of 420 x 590 x 195mm size with pillar cock, C.P.Angular stop cock, long thread of approved make continental including SS bottle trap of necessary pipe connection up to the outside face of the wall, having Telephonic Black / Colour Granite of 180 mm thick fixed on Black Kadappa Framework, etc. Complete as directed by Engineer in charge. |
| 263 | Providing and fixing white glazed urinal with Pressmatic auto closing valve having flow rate upto 4.0 Litre / Minute of Jaquar / Cera / Hindware / Perry ware or equivalent make with P.V.C. waste pipe with fitting arrangement etc. complete as directed by Engineer-in-charge. (Make shall conform to manufacturer's Green product and shall got approved from the Engineer In Charge.) |
| 264 | Providing and fixing 15cm rigid PVC Nahani trap including PVC grating, bend, connecting piece of UPVC pipe upto the outside face of wall ,making the good damagedsur face and testing etc.complete(Prior approval of sample and brandby Ex. Engr. is necessary before use) |
| 265 | Providing and fixing C.P. Angular stop clock with wall flange of approved make continental including necessary sockets/union nut etc. complete. |
| 266 | Providing and fixing C.P. 2 Way BIB cock with wall flange of approved make including necessary sockets/ union nut etc. complete as directed by Engineer in charge. |
| 267 | Providing and laying cast iron pipes of B class of 80mm diameter with sockets and spigot ends/ flanges and cast centrifugally/vertically including specials, laying pipes and back filling the trench complete including excavation. |
| 268 | Providing and laying cast iron pipes of B class of 100mm diameter with sockets and spigot ends/ flanges and cast centrifugally/vertically including specials, laying pipes and back filling the trench complete including excavation. |
| 269 | Providing and laying in trenches 50mm dai. UPVC pipe including necessary excavation, fittings. Refilling trenches etc.complete .Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete. |
| 270 | Providing, laying and fixing, jointing Eco-drain 110mm SN8Nu-Drain Upvc pipes or of equivalent make ,manufacture as per EN13476 or equivalent as per I.S.15328 with fittings such a bends ,tees, coupler, etc, jointing with rubber lubricant including necessary excavation, trench refilling with selective excavated material etc. complete. |
| 271 | Providing and constructing Brick Masonry Inspection Chamber 90cm x 45cm x 90cm including 1:4:8 cement concrete foundation 1:2:4 cement concrete channels half round G.S.W.pipes, Brick Masonry, plastering from inside and C.I. lid cover of 75Kilogramwith lid and frame fixed in cement concrete. |
| 272 | Providing and fixing P.V.C. Rain water pipes of 110mm outer diameter and having wall thickness of 2.2 to 2.7 mm confirming to I.S. 13592-1992 including proper rainwater receiving recess with P.V.C. plug, bend, necessary fittings, such as, offsets, shoes, inluding fixing the pipe on wall using approved wooden cleats projecting 25mm to 40mm from face of wall a fixing with clips of approved quality and One Number,filing the joint using rubber gasket with solvent cement and properly resting the shoe of pipes on C.C. or masonry blocks, including necessary scaffolding and maintenance for 3 yrs for any leakages or dislocations of pipes. All the P.V.C. fittings and additional 2 piece socket clips shall be got approved from engineer in charge etc. complete. |
| 273 | Providing and fixing 15cm x 10cm salt glazed stoneware gully trap in cement concrete 1:4:8 outside the building including cast iron grating in the sink, connecting glazed stoneware pipe, brick masonry chamber with cast iron lid and cast iron grating for the gully trap. |
| 274 | Electrical BOQ |
| 275 | Supplying and erecting HMS PVC conduit FRLS grade 25 mm dia. with necessary accessories in wall/floor with chiselling appropriately as per specification No: WG-MA/CC. |
| 276 | Supplying and laying HMS PVC conduit FRLS grade 25 mm dia with necessary accessories in RCC work/false ceiling/false flooring as per specification No. WG-MA/CC. |
| 277 | Supplying and erecting HMS PVC conduit FRLS grade 32 mm dia. with necessary accessories in wall/floor with chiselling appropriately as per specification No: WG-MA/CC. |
| 278 | Supplying and erecting HMS PVC conduit FRLS grade 20 mm dia. with PVC accessories on wall / ceiling as per specification No: WG-MA/CON. |
| 279 | Supplying and erecting HMS PVC conduit FRLS grade 25 mm dia. with PVC accessories on wall /ceiling as per specification No: WG-MA/CON. |
| 280 | Supplying and erecting mains with 2x1.5 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WG-MA/BW |
| 281 | Supplying and erecting mains with 1x1.5 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WG-MA/BW (note -1) |
| 282 | Supplying and erecting mains with 3x2.5 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WG-MA/BW |
| 283 | Supplying and erecting mains with 3x4 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WG-MA/BW |
| 284 | Supplying and erecting mains with 3x6 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WG-MA/BW |
| 285 | Supplying and erecting mains with 3x10 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WG-MA/BW |
| 286 | Supplying and erecting PVC insulated PVC round sheathed 1.5 sq.mm (30 no. x 0.25 mm dia.) 3 core flexible multi stranded copper Industrial cable for voltage grade up to 1.1 kV |
| 287 | Supplying and erecting PVC insulated PVC round sheathed 2.5 sq.mm (50 no. x 0.25 mm dia.) 3 core flexible multi stranded copper Industrial cable for voltage grade up to 1.1 kV |
| 288 | Supplying 16 amp. 3 pin plug Top bakelite type of 230 V. A.C. supply. |
| 289 | Supplying and erecting modular type switch 6A / 10A duly erected on provided plate and box with wiring connections complete. |
| 290 | Supplying and erecting modular type bell-push with indicator 2 modules 6A / 10A, duly erected on provided plate and box with wiring connections complete. |
| 291 | Supplying and erecting modular type switch 16 / 20 A with indicator, duly erected on provided plate and box with wiring connections complete. |
| 292 | Supplying and erecting modular type D.P. switch 32A with indicator, duly erected on provided plate and box with wiring connections complete. |
| 293 | Supplying and erecting modular type 3 pin 6A multi socket with safety shutter, duly erected on provided plate and box with wiring connections complete. |
| 294 | Supplying and erecting modular type 3 pin 6 / 16A multi socket with safety shutter, duly erected on provided plate and box with wiring connections complete. |
| 295 | Supplying and erecting modular type T.V. socket single outlet, duly erected on provided plate and box with wiring connections complete. |
| 296 | Supplying and erecting modular type telephone socket one gang with safety shutter, duly erected on provided plate and box with wiring connections complete. |
| 297 | Supplying and erecting modular type computer Jack RJ45 with safety shutter, duly erected on provided plate and box with wiring connections complete. |
| 298 | Supplying and erecting PVC Surface modular switch box with double mounting plate for 2 module duly erected. |
| 299 | Supplying and erecting PVC Surface modular switch box with double mounting plate for 4 module duly erected. |
| 300 | Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 2 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background. |
| 301 | Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 3 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background. |
| 302 | Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 4 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background. |
| 303 | Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 6 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background. |
| 304 | Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 8 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background. |
| 305 | Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 12 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background. |
| 306 | Point wiring for light/bell concealed type in min 20 mm FRLS grade HMS PVC conduit with 1.5 sq.mm. (2+1E) FRLSH grade copper wires, modular type switch, earthing and required accessories as per specification No: WG-PW/CW |
| 307 | Point wiring for light/bell concealed type in min 20 mm FRLS grade HMS PVC conduit with 1.5 sq.mm. (2+1E) FRLSH grade copper wires, modular type switch, earthing and required accessories as per specification No: WG-PW/CW(Note 1- In case length of point wiring exceeds 6 meters, add 10% of rate, for every additional length of 1 metre or part thereof.) |
| 308 | Two Way Control Point wiring for light/bell concealed type in min 20 mm FRLS grade HMS PVC conduit with 1.5 sq.mm. (2+1E) FRLSH grade copper wires, modular type switch, earthing and required accessories as per specification No: WG-PW/CW (Note3) |
| 309 | Point wiring for ceiling fan concealed type in min 20 mm FRLS grade HMS PVC conduit with 1.5 sq.mm. (2+1E) FRLSH grade copper wires, modular type switch, earthing and required accessories as per specification No: WG-PW/CW |
| 310 | Point wiring for ceiling fan concealed type in min 20 mm FRLS grade HMS PVC conduit with 1.5 sq.mm. (2+1E) FRLSH grade copper wires, modular type switch, earthing and required accessories as per specification No: WG-PW/CW (Note 1- In case length of point wiring exceeds 6 meters, add 10% of rate, for every additional length of 1 metre or part thereof.) |
| 311 | Point wiring for independent plug, concealed type in min 20 mm FRLS grade HMS PVC conduit with 1.5 sq.mm (2+1E) FRLSH grade copper wires, modular type switch, earthing and required accessories as per specification No WG-PW/SW |
| 312 | Point wiring for light/bell/exhaust fan in PVC trunking (casing-capping) with 1.5 sq.mm (2+1E) FRLSH grade copper wire, modular type switch, earthing and required accessories as per specification No: WG-PW/SW |
| 313 | Secondary point wiring for additional light/ bell point, concealed type in min 20 mm FRLS grade PVC conduit with 1.5 sq.mm. (2+1E) FRLSH grade copper wires with required accessories as per specification No: WG-PW/CW |
| 314 | Wiring for plug on board with Switch socket surface/concealed type, copper wiring and earthing and with modular accessories as per specification No: WG-PW/CW |
| 315 | Supplying & erecting 4 pair telephone copper cable 0.5 mm dia. with high density polyethylene insulation, polyester taped, Nylon Rip Cord & grey colour sheathed with FR PVC, conforming to ITD specification S/WS 113C laid in provided PVC casing capping/conduit as per specification No. WG-TW |
| 316 | Supplying & erecting co-axial copper cable low voltage grade tri-shielded RG-6 as per specification No. WG-TW |
| 317 | Supplying and erecting 15m VGA cord low voltage grade to be laid in provided conduits and terminating with male/female VGA connectors complete. |
| 318 | Supplying and erecting 10m HDMI cord low voltage grade minimum 4k compliant to be laid in provided conduits with male/female 19 pin HDMI connectors complete. |
| 319 | Supplying and erecting 15m HDMI cord low voltage grade minimum 4k compliant to be laid in provided conduits with male/female 19 pin HDMI connectors complete. |
| 320 | Supplying and erecting 20m HDMI cord low voltage grade minimum 4k compliant to be laid in provided conduits with male/female 19 pin HDMI connectors complete. |
| 321 | Supplying, erecting & commissioning MDF Box 50x50 pairs made from min. 1.5mm thick MS sheet as per specification no. WG-TW |
| 322 | Supplying, erecting & commissioning 10 pairs FR junction box with moulded plastic enclosure as per specification no. WG-TW |
| 323 | Supplying, erecting & commissioning 20 pairs FR junction box with moulded plastic enclosure as per specification no. WG-TW |
| 324 | Supplying, erecting & commissioning 30 pairs FR junction box with moulded plastic enclosure as per specification no. WG-TW |
| 325 | Supplying, erecting & commissioning 10 pair module for connection & disconnection of telephone cable as per specification no. WG-TW |
| 326 | Supplying, installing, testing & commissioning digital (hybrid) type EPABX of 3 x 8 extensions complete. (Note - 1 additional 16 extension card for digital (hybrid) type EPABX) |
| 327 | Supplying and installing, testing & commissioning of digital (hybrid) type EPABX of 6 x 32 extensions suitable upto 96 extensions complete. |
| 328 | Supplying and installing cat-6 cable suitable for networking as per specification no. WG-COC/NC |
| 329 | Supplying and erecting LSZH armoured multimode optical fibre cable with 6 fibres, core dia 50/125 µm (OM3), suitable upto 10 GBPS, ethernet distance at 850 nm of wavelength, on wall/ceiling or laid in provided pipe/trench as per specification no. WG-COC/OFC LSZH |
| 330 | Supplying and fixing 2 m UTP patch cord of cat 6 type in position as per specification No. WG-COC/PC |
| 331 | Supplying, fixing, and configuring 24 ports, POE switch in provided rack as per specification No. WG-NWC/ENS |
| 332 | Supplying, fixing, and configuring 24 ports with 4 (SFP+) port, ethernet managed switch with web view/CLI, 6KV surge protection on ethernet port and console port for management in provided rack as per specification no. WG-NWC/GBS |
| 333 | Supplying, fixing, and configuring broadband ADSL router with all accessories, on provided rack as per specification No. WG-NWC/ADSL |
| 334 | Supplying and fixing tool-less IO (Ethernet) flush/surface type in provided modular box as per specification no. WG-NAS/IO |
| 335 | Supplying and fixing 24 port patch panel with tool-less keystone jacks in provided U Rack complete as per specification no. WG-NAS/PP |
| 336 | Supplying and fixing 6U wall mount rack (Dimension-DxWxH – 500x600x367 mm) as per specification No. WG-NAS/RAK |
| 337 | Supplying and fixing manageable wireless 2x2 Mesh Router, 50 m range, dual-band 802.11 n/ac unified wireless access point complete as per specification no. WG-NAS/LAP1 |
| 338 | Supplying and erecting LED square / circular Max. 18 W down lighter/ Panel Light having pressure die-cast aluminium housing, polystyrene diffuser having system lumens output of Min. 2000 Lumens, min. efficacy of 110 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., max. ripple of 5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 2.5 kV, Life class of 50,000 Hrs. at L70B50, including driver, having mounting arrangement with board for surface type or spring loaded mounting clips complete with 3 years warranty. |
| 339 | Supplying and erecting LED square / circular Max. 25 W down lighter/ Panel Light having pressure die-cast aluminium housing, polystyrene diffuser having system lumens output of Min. 2750 Lumens, min. efficacy of 110 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., max. ripple of 5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 2.5 kV, Life class of 50,000 Hrs. at L70B50, including driver, having mounting arrangement with board for surface type or spring loaded mounting clips complete with 3 years warranty. |
| 340 | Supplying and erecting LED Panel Light(600mm X 600mm) Max. 35 W having CRCA powder coated housing, polystyrene diffuser having system lumens output of Min 4200 Lumens, min. efficacy of 120 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., max. ripple of 5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 2.5 kV, Life class of 50,000 Hrs. at L70B50 including driver, having mounting arrangement with board for surface type or spring loaded mounting clips complete with 3 years warranty. |
| 341 | Supplying and erecting LED Strip light 5m Length Max. 45 W IP20 class having minimum lumens output of 800 Lumens/m, min. efficacy of 90 lumen/W, CRI>80, CCT upto 5000K, Beam Angle of 110 deg., THD<10%, p.f. >0.95, operating range of 230-270V, Life class of 30,000 Hrs. at L70B50, including driver with 1 year warranty. |
| 342 | Supplying LED concealed type foot / step light with aluminium body for indoor/outdoor application suitable for 4W-6W LED including driver and erecting by making necessary arrangement / recess in wall to make it flush with surface with 1 year warranty. |
| 343 | Supplying and erecting bulk head LED fitting max. 10W with high transitivity diffuser with system lumens output of min. 1100 lumens, min. efficacy of 110 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., THD<10%, p.f. >0.95, operating range of 140-260V, in built surge protection of 2.5 kV, Life class of 50,000 Hrs. at L70B50, including driver, IP66, IK09 rated on provided PVC Block / wooden board with 3 years warranty. |
| 344 | Supplying and erecting anodized aluminium corridor / passage / mirror light LED fitting (2 feet) Max. 12W with high transitivity diffuser with min. system lumens output of 1200 lumens, min. efficacy of 100 lumen/W, CRI>80, CCT upto 6000K, Beam Angle of 110 deg., Ripple<5%, THD<10%, p.f. >0.95, operating range of 200-270V, surge protection of 2 kV, Life class of 50,000 Hrs. at L70B50, including driver with end caps on provided PVC Block / wooden board with 3 years warranty. |
| 345 | Supplying and erecting anodized aluminium corridor / passage light LED fitting (4 feet) Max. 22W with high transitivity diffuser with system lumens output of Min.2200 lumens , min. efficacy of 100 lumen/W, CRI>80, CCT upto 6000K, Beam Angle of 110 deg., Ripple<5%, THD<10%, p.f. >0.95, operating range of 200-270V, surge protection of 2 kV, Life class of 50,000 Hrs. at L70B50, including driver, with end caps on provided PVC Block / wooden board with 3 years warranty. |
| 346 | Supplying and erecting ding dong / electronic musical type call bell with heavy duty coil suitable to operate on 230V A.C. supply erected on polished double wooden block/sunmica block of suitable size. |
| 347 | Supplying and erecting integrated LED street light fitting 40 to 50W IP65 & IK08 class having single piece pressure die-cast aluminium housing, having system lumens output of Min. 4400 Lumens, min. efficacy of 110 lumen/W, CRI>70, CCT upto 6500K,THD<10%, p.f. >0.95, operating range of 140-270V, inbuilt surge protection of 10 kV, Life class of 50,000 Hrs. at L70B50, including driver complete with 3 Years warranty as per specification No FG-ODF/FLS2. |
| 348 | Supplying and erecting integrated LED street light fitting 70-75W IP65 & IK08 class having single piece pressure die-cast aluminium housing, having system lumens output of Min. 7700 Lumens, min. efficacy of 110 lumen/W, CRI>70, CCT upto 6500K,THD<10%, p.f. >0.95, operating range of 140-270V, inbuilt surge protection of 10 kV, Life class of 50,000 Hrs. at L70B50, including driver complete with 3 Years warranty as per specification No FG-ODF/FLS2. |
| 349 | Supplying and erecting street light Wall bracket made from 40 mm. dia ‘ G.I. pipe 1.2 m. in total length complete as per specification no. FG-BKT/WB |
| 350 | Supplying and erecting Street light bracket for erection of Single fitting made from 40 mm. dia ‘B’ class G.I. pipe 1.0 m. in length along with pole cap of 300 mm length 100 mm dia duly welded as per specification no. FG-BKT/BPC |
| 351 | Supplying and erecting air circulator 600 mm. sweep oscillating type, wall mounting 1440 RPM without speed regulator, overheat protection unit, totally enclosed, flame proof motor suitable for 230/250 volts single phase, 50 cycles A.C. supply, core lead wire and with moisture proof treatment to winding and with ‘E’ class insulation. |
| 352 | Supplying and erecting fresh air cum exhaust fan of light duty 250 V A.C. 50 cycles 225mm. 1400 RPM rust proof body & blades, wire mesh, duly erected, complete. |
| 353 | Supplying and erecting exhaust fan heavy duty 230 V A.C. 50 cycles 375/380 mm. 1400 RPM complete erected in position as per specification no. FG-FN/EXF |
| 354 | Supplying and erecting Energy Saving BLDC Ceiling fan 230 V A.C. 50 cycles 1200 mm, max. energy consumption of 28W having service ratio (CMM/W) of Min. 8 , PF>0.9, THD<10% with IR remote control/compatible speed regulator, Temperature Rise of Max. 40 deg. C, having external mounted control PCB completely erected in position as per specification no. FG-FN/CF |
| 355 | Supplying and erecting fan clamp of 30 x 5 mm. M.S. flat of required length and 10 mm. M.S. bolt and nuts erected with necessary hook of 10 mm. M.S. round bar and painted. |
| 356 | Supplying and erecting ‘B’ class G.I .pipe / M.S. pipe down rod duly painted for fan complete erected with PVC three core flexible cable 1 sq. mm copper PVC wire. |
| 357 | Supplying & erecting 22 SWG G.I sheet metal cawl sector shaped with 25 x 25 x 3 (mm) angle iron frame, metal mesh to avoid birds entry with necessary material, suitable for exhaust fan of 300 mm as per specification no FG-FAS/MSC |
| 358 | Supplying & erecting 22 SWG G.I sheet metal cawl sector shaped with 25 x 25 x 3 (mm) angle iron frame, metal mesh to avoid birds entry with necessary material, suitable for exhaust fan of 400 mm as per specification no FG-FAS/MSC |
| 359 | Supplying and erecting midget type 3.0 litres instant type water heater of rustproof & shockproof ABS plastic body, high grade SS inner tank & 3kW heating element with corrosion & hard water protection, with minimum 3 safety protections (i.e. thermostat & thermal cut-out, function valve) complete with 6.5 bar pressure withstanding capacity 230/250V, 50Hz, A.C. supply with inlet and outlet, with 3 core PVC flexible copper wire leads duly tested and marking sr. no. and date of erection complete. |
| 360 | Supplying, installing, testing & commissioning split type room air conditioning unit 2.8TR to 3.2TR capacity with refrigerant R32 415V, 50 Hz, A.C. supply having 1 no of air handling unit (Mega split) mounting type complete with temperature display on indoor unit, noise level maximum 50dBA at position as per specification no. APAC/ WAC |
| 361 | Supplying, installing, testing & commissioning cassette type room Air conditioning unit 4TR to 4.4TR capacity with refrigerant R32/410A 415V, 50 Hz, A.C. supply having 1 no of air handling unit (Mega split) mounting type complete with temperature display on indoor unit, minimum dust filter, noise level maximum 50dBA at position as per specification no. APAC/ WAC |
| 362 | Supplying & erecting seamless outside & inside, smooth, dry and clean copper pipe with ROHS compliant suitable for refrigerant having 22SWG thickness and inner dia/size 12mm complete. |
| 363 | Supplying & erecting seamless outside & inside, smooth, dry and clean copper pipe with ROHS compliant suitable for refrigerant having 22SWG thickness and inner dia/size 16mm complete. |
| 364 | Supplying, erecting, testing and commissioning self contained water cooler 230/250V 50Hz nominal cooling capacity of 40 litres per hour and storage capacity 80 litres with partially stainless steel body As per specification no. APWCR/ WC |
| 365 | Supplying and erecting ultra violet storage type water purifier (RO+UV+UF) with softener for safe drinking water consisting of UV germicidal tube of 8W capacity choke made of copper wire and two indicator lamps with output of purified water minimum 0.33 litre/min with activated carbon filter and softener operating on 230V, single phase A.C. supply with UV fail & filter change indication system .(for TDS more than 200) |
| 366 | Supplying, erecting, testing and commissioning of 6kVA capacity online pure sine wave with backup time of ....... hrs. PWM & IGBT based UPS with 0.9 to unity output pf, single phase input & 1 phase output complete with all protections as per specification no. AP-UPS |
| 367 | Supplying, erecting, testing and commissioning of 10kVA capacity online pure sine wave with backup time of ....... hrs. PWM & IGBT based UPS with 0.9 to unity output pf, single phase input & 1 phase output complete with all protections as per specification no. AP-UPS |
| 368 | Supplying, erecting, testing and commissioning of 20kVA capacity online pure sine wave, with backup time of ....... hrs. PWM & IGBT based UPS with 0.9 to unity output pf, 3 phase input and 3 phase output complete with all protections as per specification no. AP-UPS |
| 369 | Supplying and erecting 12V/26Ah SMF battery with battery terminal wire, duly charged with 24 months warranty complete |
| 370 | Supplying and erecting 12V/42Ah SMF battery with battery terminal wire, duly charged with 24 months warranty complete |
| 371 | Supplying and erecting 12 V/65Ah SMF battery with battery terminal wire, duly charged complete with 24 months warranty complete |
| 372 | Carrying out core cutting of size 3\\" to 5\\" dia x 15\\" length in the C.C./rock/stone wall with the help of specialized core cutting machine in proper manner and finishing the site as original. |
| 373 | Supplying and erecting elastomeric nitrile rubber / foam tube type sleeves for coating and insulating on provided PC / copper pipes having 9 mm thickness and inner diameter / sizes 12 mm for solar water heater/AC system. |
| 374 | Supplying and erecting elastomeric nitrile rubber / foam tube type sleeves for coating and insulating on provided PC / copper pipes having 9 mm thickness and inner diameter / sizes 16 mm for solar water heater/AC system. |
| 375 | Supplying & erecting four pole ON LOAD change over switch, 415V, 160A, open execution having staggered termination, phase barrier, shroud termination and terminal cover along with auxiliary contacts and ready to upgrade with fuse protection kit, rotary handle, operational current category AC23A complying to IS/IEC 60947-3 Part-1/3. |
| 376 | Supplying & erecting three phase, 415V, street light control panel up to the max load of 6kW, TPN MCB 40A, powder coated CRCA 14 SWG sheet, outdoor type, having IP54,IK10 protection, suitable rating contactor, 24 hrs. astronomical time switch with minimum 5 years battery back up, auto/manual selector switch, ON/OFF push buttons, indicator lamps, control wiring, metering device, etc. for automatic operation, with overcurrent, short circuit, earth fault protection on provided iron frame / CC foundation. |
| 377 | Supplying, erecting & marking SPMCB 6A to 32A, C-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB |
| 378 | Supplying, erecting & marking SPMCB 6A to 32A, B-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB |
| 379 | Supplying, erecting & marking TPMCB 6A to 32A, with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB |
| 380 | Supplying, erecting & marking TPMCB 40A to 63A, with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB |
| 381 | Supplying, erecting & marking FPMCB 6A to 32A, with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB |
| 382 | Supplying, erecting & marking FPMCB 40A to 63A, with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB |
| 383 | Supplying & erecting triple pole and neutral distribution board (TPNDB), SPMCB of 8 ways / phase (24 poles), with door, 1.2mm thickness surface/ flush mounted, IP 43 Protection on iron/GI frame (horizontal busbar type) as per specification no. SW-SWR/MCBDB |
| 384 | Supplying & erecting triple pole and neutral distribution board (TPNDB), SP/TP MCBs total 4 ways /12 Poles, with door, 1.2mm thickness surface/flush mounted, IP 43 Protection on iron/GI frame (vertical busbar type) as per specification no. SW-SWR/MCBDB |
| 385 | Supplying and erecting single pole and neutral distribution board (SPNDB), with 2 ways for incoming and 2 ways (2 poles) for outgoing SP MCBs, with door, 1.2mm thickness surface / flush mounted, IP 43 Protection on iron / GI frame as per specification no. SW-SWR/MCBDB |
| 386 | Supplying and erecting single pole and neutral distribution board (SPNDB), with 2 ways for incoming and 6 ways (6 poles) for outgoing SP MCBs, with door, 1.2mm thickness surface / flush mounted, IP 43 Protection on iron / GI frame as per specification no. SW-SWR/MCBDB |
| 387 | Supplying and erecting single pole and neutral distribution board (SPNDB), with 2 ways for incoming and 10 ways (10 poles) for outgoing SP MCBs, with door, 1.2mm thickness surface / flush mounted, IP 43 Protection on iron / GI frame as per specification no. SW-SWR/MCBDB |
| 388 | Supplying & erecting CRCA sheet metal one way enclosures of 1.2mm thickness suitable for DP MCB /TP MCB/FP MCB/RCCB/RCBO complete erected on angle iron/GI frame. |
| 389 | Supplying & erecting triple pole and neutral distribution board (TPNDB), 3 pole/4 pole MCCB as incomer & outgoing SP MCB (24 poles) or TP MCB of 8 ways (24 poles), with door, 1.2mm thickness, surface/flush mounted, on iron/GI frame (vertical busbar type) as per specification no. SW-SWR/MCBDB1 |
| 390 | Supplying & erecting triple pole and neutral distribution board (TPNDB), 3 pole/4 pole MCCB as incomer & outgoing SP MCB (36 poles) or TP MCB of 12 ways (36 poles), with door, 1.2mm thickness, surface/flush mounted, on iron/GI frame (vertical busbar type) as per specification no. SW-SWR/MCBDB1 |
| 391 | Providing & erecting 4 Pole MCCB, 415 V, 100A, rated short-circuit breaking capacity 25 kA (Ics=100% of Icu), adjustable thermal (overload) setting and fixed magnetic setting with provided leads, provision for installation of shunt/UV/trip alarm contact. MCCB with phase barriers on both sides, insulation withstand capacity 800V, no line-load bias in provided enclosure/panel as per specification no. SW-SWR/MCCB |
| 392 | Providing & erecting 4 Pole MCCB, 415V, 200A, rated short-circuit breaking capacity 25 kA (Ics=100% of Icu), adjustable thermal (overload) setting and adjustable magnetic setting with provided leads, provision for installation of shunt/UV/trip alarm contact and MCCB should have phase barriers both sides, with insulation withstand capacity 800V, no line-load bias in provided enclosure/panel as per specification no. SW-SWR/MCCB |
| 393 | Providing & erecting 4 Pole MCCB 415V, 250A, rated short-circuit breaking capacity 36 kA (Ics=100% of Icu) adjustable thermal (overload) setting and adjustable magnetic setting with provided leads, provision for installation of shunt/UV/trip alarm contact and MCCB should have phase barriers both sides, with insulation withstand capacity 800V, no line-load bias in provided enclosure/panel as per specification no. SW-SWR/MCCB |
| 394 | Supplying, fixing and commissioning 2 pole, RCBO 6/10/16/20/25A, with overcurrent, rated short-circuit breaking capacity (10 kA) and earth leakage protection, with 30/100/300 mA sensitivity and short circuit and earth leakage trip indication as per specification no SW-RCCB/RCBO |
| 395 | Supplying, fixing and commissioning 2 pole RCBO 32/40A, with overcurrent, rated short-circuit breaking capacity (10 kA) and earth leakage protection, with 30/100/300 mA sensitivity and short circuit and earth leakage trip indication as per specification no SW-RCCB/RCBO |
| 396 | Supplying, fixing and commissioning 2 pole RCBO 63A, with overcurrent, rated short-circuit breaking capacity (10 kA) and earth leakage protection, with 30/100/300 mA sensitivity and short circuit and earth leakage trip indication as per specification no SW-RCCB/RCBO |
| 397 | Supplying, fixing and commissioning 4 pole RCBO 6/10/16/20/25A, with overcurrent, rated short-circuit breaking capacity (10 kA) and earth leakage protection, with 30/100/300 mA sensitivity and short circuit and earth leakage trip indications per specification no SW-RCCB/RCBO |
| 398 | Supplying, fixing and commissioning 4 pole RCBO 32/40A, with overcurrent, rated short-circuit breaking capacity (10 kA) and earth leakage protection, with 30/100/300 mA sensitivity and short circuit and earth leakage trip indication as per specification no SW-RCCB/RCBO |
| 399 | Providing & erecting floor/wall mounting, MCCB panel board, with door, suitable for four pole incoming 250A, 4 ways four pole outgoing, up to 100 A MCCBs on iron frame, as per specification no SW-SWR/MCCBPB. (Excluding MCCBs) |
| 400 | Providing & erecting floor/wall mounting, MCCB panel board, with door, suitable for four pole incoming 250A, 12 ways four pole outgoing, up to 100 A MCCBs on iron frame, as per specification no. SW-SWR/MCCBPB. (Excluding MCCBs) |
| 401 | Providing & erecting floor/wall mounting, MCCB panel board, with door, suitable for four pole incoming 400A, 12 ways four pole outgoing, up to 100 A MCCBs on iron frame, as per specification no. SW-SWR/MCCBPB. (Excluding MCCBs) |
| 402 | Supplying and erecting terminal spreaders suitable for 4 pole, up to 100A MCCB (Set of 8) |
| 403 | Supplying and erecting terminal spreaders suitable for 4 pole, above 100A up to 250A MCCB (Set of 8) |
| 404 | Supplying and erecting terminal spreaders suitable for 4 pole, above 400A up to 630A MCCB (Set of 8) |
| 405 | Supplying and erecting extended rotary handle for MCCB with adjustable telescopic rod suitable for up to 250A MCCB. |
| 406 | Supplying and erecting SS enclosure for MCCB suitable for up to 100A MCCB. |
| 407 | Supplying and erecting SS enclosure for MCCB suitable for 125A to 200A MCCB. |
| 408 | Supplying and erecting SS enclosure for MCCB suitable for above 250 A up to 800A MCCB. |
| 409 | Supplying and erecting iron work, sheet metal work consisting of CRCA sheets, various sections of iron, plates, chequered plates, rods, bars, MS pipes, etc. for panel board or any other purpose with bending, cutting, drilling and welding complete erected at the position with necessary materials duly painted with one coat of red oxide and two coats of enamel paint to match the switchgears or as per directions by the authority. |
| 410 | Supplying and erecting AC Three Phase Four wire Multifunction Energy Meter of Rating 10 - 60A, Class 1.0 with din rail / Panel mounting to measures and display parameters with RS485 Modbus communication port. mounting whole current operated meter to measures and display V, I, kWh, KVAh, KW, KVA, P.F, THD, RS 485 Communication port. Electrical parameters shall be available on com port with their mapping address open for third party software |
| 411 | Supply installation & Commissioning of IoT System Controller / Gateway for electrical and allied services with Inbuilt GPRS, WIFI, LAN Capabilities for Multifunction Meters, Level Sensors , temperature sensors etc. and able to collect data from communicable device of available protocol on real time basis with following specifications 1) ARM based Controller (1.6 Ghz processor with 1.2 GB RAM with inbuilt 16GB memory 2) Inbuilt 4G/3G/GPRS modem with fallback and suitable antenna to communicate with cloud 3)Data services must be from at least two reliable service providers and system should support automatic switching to 2nd service provider in case of low network without any intervention. System should support changing of service providers without changing SIM cards 4)Gateway must have Modbus, MBUS, Ethernet and DLMS Any other future open-source protocol (that uses RS485 or TCP port) must be provided free of cost for the period of at least 1 year 5) Must have one RS485 and one ethernet port 6) The controller must send data with TLS encryption and the data on controller must be encrypted 7) Operable with 230V AC supply Gateway shall collect maximum 15-20 devices for data collection 8) Software shall support for AI application with critical alarm on mobile app |
| 412 | Supply & Commissioning of Cloud based IoT system Monitoring Software with Cloud and Internet Subscription for 2 Year for Data Analytics, AI Algorithm, Alerts, Automatic Data storage at local computer, Trends, Dashboard, alerts. Access on mobile through web link, Alerts to mobile with AI Technology Real-time monitoring of all the field devices measurements (Electricity, Water, Gas, Temperature, Pressure, Levels, etc.) in a single location. Sending of events & historical data through SMS (Using GSM Modem) for multiple persons at custom intervals. And configuration of mobile numbers for the same. The Analytical module shall be in built to analyze various events/issues that may be occurring in the electrical network. Must have user customizable dashboards and SLD (without any coding/ scripting). Reporting must be user-configurable and changeable. Multi-site data viewing within same interface without any physical cable connection of sites to monitoring |
| 413 | Supply installation & Commissioning of Input Output card 20 Channel for accessibility of input from potential free contact and same to be used to monitor the status of circuit breaker/Meters/Sensors etc., i.e. On/ Off/Trip Status and shall be able to communicate through RS 485 Port. |
| 414 | Supply & installation of Enclosure for box IOT Controller / IO / SMPS |
| 415 | Supply installation & Commissioning of wireless Thermal Sensor that enables the continuous thermal condition monitoring of cables Connections, withdrawable Circuit Breakers Connections and busbar connections. operated from the electromagnetic field generated by the current flowing through the monitored conductor. with Electric access point and able to communicate using wired/wireless communication protocol. |
| 416 | Annual web based charges for data storage on cloud for various Devices, Meters, sensors etc. for 2 years |
| 417 | Supplying and erecting LT current transformer with bar primary 50/5 to 1000/5 ratio with 15 VA burden erected in provided CRCA box duly secured with insulating materials connected to the meter with test certificates. |
| 418 | Supplying and erecting 50 kVAr, 440 V 3 phase, 50 Hz., Contactor Logic & Intelligent Relay micro APFC passive filter panel, consisting of suitable steps of APP/MPP type capacitor units with Detuned (harmonic filter) reactors of suitable rating , APFC panel shall be compliance to IEC 61439 and power quality IEC 61921 standard as per specification no CP-ED/APFC |
| 419 | Supplying, erecting & terminating XLPE insulated unarmoured cable 1100 V 1 core 95 sq. mm. aluminium conductor complete erected with lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL |
| 420 | Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3 core 2.5 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL |
| 421 | Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3 core 4 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL |
| 422 | Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3 core 10 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL |
| 423 | Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½ core 70 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL |
| 424 | Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 4 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL |
| 425 | Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 6 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL |
| 426 | Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 10 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL |
| 427 | Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 16 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL |
| 428 | Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 25 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL |
| 429 | Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 35 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL |
| 430 | Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 50 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL |
| 431 | Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 95 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL |
| 432 | Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 185 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL |
| 433 | Supplying, erecting & terminating XLPE insulated unarmoured cable 1100 V. 1 core 50 sq. mm. copper conductor complete erected with provided lugs, laid in provided control panel /distribution boards / pipe as per specification no. CB-LT/CU |
| 434 | Supplying, erecting & terminating XLPE insulated unarmoured cable 1100 V. 1 core 70 sq. mm. copper conductor complete erected with provided lugs, laid in provided control panel/distribution boards / pipe as per specification no. CB-LT/CU |
| 435 | Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3 core 2.5 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU |
| 436 | Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3 core 4 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU |
| 437 | Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3 core 6 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU |
| 438 | Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3 core 25 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU |
| 439 | Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 4 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU |
| 440 | Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 6 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU |
| 441 | Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 10 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU |
| 442 | Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 25 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU |
| 443 | Supplying and laying (including excavation of suitable width & depth up to 90 cm) 50 mm outside dia. double wall corrugated pipes (DWC) of HDPE for enclosing cable below ground/road surface, to required depth complete. |
| 444 | Supplying and laying (including excavation of suitable width & depth up to 90 cm) 90 mm outside dia. double wall corrugated pipes (DWC) of HDPE for enclosing cable below ground/road surface, to required depth complete. |
| 445 | Supplying & erecting FRP box of size 150mm x 125mm x 100 mm, 2.7 mm thick complete on pole/wall as per specification No. CB-SB |
| 446 | Providing & erecting hot dipped galvanised ladder type cable tray manufactured from 16 SWG (1.6 mm thick) GI sheet of 150 mm width & 75 mm height complete with necessary coupler plates & hardware. |
| 447 | Providing & erecting hot dipped galvanised ladder type cable tray manufactured from 16 SWG (1.6 mm thick) GI sheet of 300 mm width & 75 mm height complete with necessary coupler plates & hardware. |
| 448 | Providing & erecting hot dipped galvanised cover suitable for perforated type Cable tray manufactured from 18 SWG (1.2 mm thick) GI sheet of 150 mm width & 20 mm height complete with necessary hardware. |
| 449 | Supplying and erecting G.I. pipe pole ‘B’ class 80 mm dia 6 m long with pole cap, base plate in provided foundation as per specification no. OH-PL/GIP |
| 450 | Providing earthing with galvanized iron earth plate size 60 x 60 x 0.6 cm complete with all materials, testing & recording the results as per specification no. EA-EP |
| 451 | Providing earthing with galvanized iron earth plate size 60 x 60 x 0.6 cm with funnel with a wire mesh for watering and brick masonry block C.l. cover complete with all materials, testing & recording the results as per specification no. EA-EP |
| 452 | Providing pipe type earthing with 40mm. dia. G.I. pipe or 20 mm dia. G.I. Rod complete with all materials testing and recording the results as per specification no. EA-EP |
| 453 | Supplying and erecting GI strip of high purity required size used for earthing on wall and/or any other purpose with necessary GI clamps fixed on wall painted with bituminous paint with joints required. As per specification no EA-EP. |
| 454 | Supplying and erecting minimum Three & above star rated submersible pump set suitable for erection on open well of 2.25 KW/3 HP with 415 V 50 c/s. A.C. supply, having delivery head from 27 to 9 m and discharge from 300 to 660 litres. per minute & pipe of Suction 65mm /Delivery 50 mm diameter erected with necessary H type clamps as per specification No. WP-OSP |
| 455 | Supplying & erecting flat flexible 3 core 1.5 sq.mm PVC sheathed submersible type copper cable suitably clamped at fixed intervals with column pipe assembly complete. |
| 456 | Supplying & erecting automatic control panel for 3 Phase , 415 volt, A.C, Submersible/centrifugal pump set up to 7.5 HP consisting of DOL starter having relay range 9-14 AMP,S.P.P., Combined ammeter/ voltmeter, phase indicating lamp enclosed in CRCA powder coated Vibration proof enclosure with IP 54 protection. Control Panel should offer single phasing, phase reversal, phase imbalance etc . |
| 457 | Supplying, installation, testing and commissioning of main fire pump (MFP / EP) suitable for water discharge of 1800 to 2280 LPM at 80 to 60 m head driven by electric motor 415 volts, 3 phase 50 Hz, AC supply of 37kW or of suitable kW capacity for manual/automatic operation and consisting of following :(a) Horizontal type, single stage, centrifugal/split casing pump of cast iron body & bronze impeller with stainless steel shaft(SS410 grade), mechanical seal conforming to IS 1520.(b) Squirrel cage induction motor, TEFC, synchronous speed 3000 RPM, suitable for operation with IP 55 protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS-325.(c) M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required.(d) Erected on provided suitable size cement concrete foundation duly plastered with anti vibration pads with perfect aligning, proper levelling complete pump set with accessories duly painted with two coats of synthetic enamel paint of fire red colour over a coat of primer (ISC code 536 as per IS 2932 of 2003) complete, as per specification no. FF-MFP/SSC/EP |
| 458 | Supplying, installation, testing and commissioning of jockey fire pump (JP) suitable for water discharge of 180 to 240 LPM at 70 to 50 m head driven by electric motor 415 volts, 3 phase 50 Hz, AC supply of 5.5 kW or of suitable kW capacity for manual/automatic operation and consisting of following :(a) Horizontal/vertical type, multi stage, centrifugal casing pump of cast iron body & bronze impeller with stainless steel shaft (SS410 grade), mechanical seal conforming to IS 1520.(b) Squirrel cage induction motor, TEFC, synchronous speed 3000 RPM, suitable for operation with IP 55 protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS-325.(c) M.S. fabricated common base plate, coupling, coupling guard, foundation bolts etc. as required.(d) Erected on provided suitable size cement concrete foundation duly plastered with anti vibration pads with perfect aligning, proper levelling complete pump set with accessories duly painted with two coats of synthetic enamel paint of fire red colour over a coat of primer (ISC code 536 as per IS 2932 of 2003)complete, as per specification no. FF-MFP/JP |
| 459 | Supplying, installation, testing and commissioning of main fire pump (MFP/DP) suitable for water discharge of 2280 to 2850 LPM at 90 to 60 m head driven by 76 HP or suitable HP capacity diesel engine at required working speed suitable for manual/automatic operation and consisting of following :(a) Horizontal type, single stage, centrifugal casing pump of cast iron body & bronze impeller with stainless steel shaft(SS410 grade), mechanical seal conforming to IS 1520.(b) Water cooled with radiator, diesel engine conforming to relevant IS standard complete with auto starting mechanism, 12/24 volts DC electric starting equipment with battery of required AH capacity with necessary charger suitable to work on 230v, 50Hz AC supply, diesel tank of minimum 150ltr capacity with first filling of diesel up to 100% level with necessary piping with valves up to engine , exhaust pipe extended up to 10 m outside pump house duly insulated with 50 mm thick glass wool with 1.0 mm thick aluminium sheet cladding, residential silencer, instruments and protection as per standard specification, stop solenoid for auto stop in the event of fault with audio indications etc. as required.(c) M.S. fabricated common base plate, coupling, coupling guard, foundation bolts etc. as required.(d) Erected on provided suitable size cement concrete foundation duly plastered with anti vibration pads with perfect aligning, proper levelling complete pump set with engine assembly and accessories duly painted with two coats of synthetic enamel paint of fire red colour over a coat of primer (ISC code 536 as per IS 2932 of 2003) complete, as per specification no. FF-MFP/SSC/DP |
| 460 | Supplying, erecting, testing & commissioning of fire pump control panel (FCP) of cubical construction, floor mounted type, fabricated from minimum 2 mm thick CRCA sheet, compartmentalised with hinged lockable doors, with enclosure protection class IP54, duly powder coated or painted with accessories duly painted with two coats of synthetic enamel paint of fire red colour over a coat of primer (ISC code 536 as per IS 2932 of 2003), cable alley, interconnection with suitable size solid copper busbar strip of adequate size for all power connections having switchgears and accessories, mountings and internal wiring with adequate size copper conductor cable, earth terminals, numbering etc. complete in all respect, suitable for satisfactory operation of main fire pump and jockey (pressurisation) pumps (1working+1standby) with necessary accessories, wiring &cabling along with allied accessories with following incoming and outgoings, suitable for automatic & manual operation on 415V, 3 phase, 50Hz ac supply asper specifications the capacity of electric motor driven pump are as followsa. Main fire pump(MFP) having capacity of 22kW 1no (1 working)b. Jockey pump(JP) capacity of suitable capacity 2 nos(1 working +1 standby,alternate run per start in auto mode)comprises of the following features & switchgears:1. Main incomer FP SFU having rotary handle with HRC fuses of suitable rating.2. Electrolytic grade copper strips for busbar of suitable sizes for main incomer and branches to motor SFU's, starters & outgoing terminals with necessary accessories like stainless steel nut bolts with spring washers for connections, mounted on required no of epoxy or porcelain support insulators of suitable ratings etc.3. Individual pump TPN SFU having rotary handle with HRC fuses of suitable rating.4. Digital voltmeter & ammeter & RYB indicating lamps & push buttons & SPP, O/L & phase reversal protection with emergency stop switch.5. TPN SPD 100kA Type 1 +2 tested.6. Required pressure transducer with pressure indication on panel with cabling required for monitoring & automatic operation of fire pumps.7. System controller to control operation of main electric fire pump, jockey (pressurization) pumps in sequence with interlocking for operation of pumps as per specification with automatic/manual operation with selector switch & alternate run of standby Pumps consisting of relays, timers. sensors, annunciation window for fault indication, complete as per specification.8.Suitable capacity electric motor starters for all individual pumps with necessary push buttons & indications.9. Siren of required capacity to be activated when main pump starts & alliedaccessories as per requirements of local CFO or as directed by engineer in charge.10. Danger board as per IS.11. Spare HRC fuses minimum 2nos of each individual rating with required bakelite fuse holder for main & jockey fire pumps MFP=(1working), JP = (1working+1standby, alternate run per start in auto mode) complete panel, as per specification no. FF-MFP/ECPADD ONA. For addition of capacity of main electric motor driven fire pump MFP (1 working) for hydrant system is more than 22kW, add as follows in the basic cost of Item no 13-5-1 towards increased capacity switchgears and motor starters for main & jockey pumps along with necessary accessories for main & jockey fire pumps MFP=(1working), JP = (1working + 1standby, alternate run per start in auto mode)2. For main electric motor driven fire hydrant system pump of 37kW capacity & relevant capacity jockey pumpB. For addition of fire sprinkler system to basic fire hydrant system control panel(FCP) which includes one main electric motor driven fire pump MFP (1working) having __kW capacity & relevant capacity jockey pumps, add as follows in the basic cost of Item no 13-5-1 towards increased capacity switchgears busbar and additional motor starters for main & jockey pumps along with necessary accessories with software & hardware for main & jockey fire pumps additional Sprinkler system MFP=(1working)@22kW, JP = (1working+1standby, alternate run per start in auto mode) @relevant capacity3. For main electric motor driven fire sprinkler system pump of 37kW capacity (1Working) & relevant capacity jockey pumps (1working+1standby, alternate run per start in auto mode,D. For addition of standby main diesel engine driven fire pump (1 standby), add as follows in the basic cost of Item no 13-5-1 towards required 12/24 v battery charger and diesel engine starter along with necessary accessories, indicators etc. with necessary interlocking and updation of control logic with interlocking for operation of pumps MFP for main (1working+1standby mode) & jockey fire pumps (1working+1standby, alternate run per start in auto mode) , add Rs 68381The control for diesel engine comprises of automatic/manual selector switch & 3 attempts starting device, timers and relays as required, push buttons, start/stop in manual mode indicating lamp for high/ low Lub. oil pressure, high water temp and engine on indication battery charger suitable for 12V/24 V DC with boost and trickle selector switch, 0-30 V DC voltmeter, and 0-20 A DC ammeter with all standard relays and accessories required for automatic operation of diesel engine with interlocking for operation of main fire pumps |
| 461 | Supplying and erecting G.I. pipe ‘C’ class ERW 25 mm dia with necessary fittings complete as per specification no. FF-PP |
| 462 | Supplying and erecting G.I. pipe ‘C’ class ERW 50 mm dia with necessary fittings complete as per specification no. FF-PP |
| 463 | Supplying and erecting G.I. pipe ‘C’ class ERW 75/80 mm dia with necessary fittings complete as per specification no. FF-PP |
| 464 | Supplying and erecting G.I. pipe ‘C’ class ERW 65 mm dia with necessary fittings complete as per specification no. FF-PP |
| 465 | Supplying and erecting G.I. pipe ‘C’ class ERW 100 mm dia with necessary fittings complete as per specification no. FF-PP |
| 466 | Supplying and erecting G.I. pipe ‘C’ class ERW 150 mm dia with necessary fittings complete as per specification no. FF-PP |
| 467 | Providing coating of bitumen paint & 4mm thick wrapping for underground 100 mm ring main of fire fighting system. |
| 468 | Providing coating of bitumen paint & 4mm thick wrapping for underground 150 mm ring main of fire fighting system. |
| 469 | Supplying and erecting 80 mm dia cast iron foot valve ball type/flap type with strainer for negative suction complete as per specification no. FF-VL/FV |
| 470 | Supplying and erecting 150 mm dia cast iron foot valve ball type/flap type with strainer for negative suction complete as per specification no. FF-VL/FV |
| 471 | Supplying and erecting 75/80 mm dia. cast iron double flange butterfly valve of size complete with PN16 pressure rating, as per specification no. FF-VL/BFV |
| 472 | Supplying and erecting 100 mm dia. cast iron double flange butterfly valve of size complete with PN16 pressure rating, as per specification no. FF-VL/BFV |
| 473 | Supplying and erecting 150 mm dia. cast iron double flange butterfly valve of size complete with PN16 pressure rating, as per specification no. FF-VL/BFV |
| 474 | Supplying and erecting 75/80 mm dia cast iron double flange NRV complete with PN16 pressure rating, as per specification no. FF-VL/NRV |
| 475 | Supplying and erecting 100 mm dia cast iron double flange NRV complete with PN16 pressure rating, as per specification no. FF-VL/NRV |
| 476 | Supplying and erecting 150 mm dia cast iron double flange ball type NRV complete with PN16 pressure rating, as per specification no. FF-VL/NRV |
| 477 | Supplying and erecting 20 mm dia gun metal gate valve complete with PN16 pressure rating, as per specification no. FF-VL/GV |
| 478 | Supplying and erecting 25 mm dia gun metal gate valve complete with PN16 pressure rating, as per specification no. FF-VL/GV |
| 479 | Supplying and erecting gun metal single outlet hydrant valve fitted with necessary accessories complete as per specification no. FF-VL/HV |
| 480 | Supplying gun metal double outlet hydrant valve fitted with necessary accessories complete as per specification no. FF-VL/HV |
| 481 | Supplying and installing one piece moulded HDPE / fibre water tank for negative suction only, having capacity 1000 litres fitted with necessary accessories complete as per specification no. FF-FFA/PT |
| 482 | Supplying and installing wall mounting swinging hose reel drum fitted with 19 mm dia. 30m long high pressure polypropylene (Polyhose) along with necessary accessories complete as per specification no. FF-FFA/HV |
| 483 | Supplying and erecting 63mm dia, reinforced rubber lined (R.R.L.) hose pipe, 15m in length, fitted with necessary accessories complete as per specification no. FF-FFA/RRL |
| 484 | Supplying and erecting gun metal branch pipe of 63 mm dia fitted with 20 mm dia detachable hexagonal nozzle complete as per specification no. FFFFA/NZ |
| 485 | Supplying and erecting 150 mm dia fire brigade header suitable for supplying water in fire tank complete as per specification no. FF-FA/FBC |
| 486 | Supplying and erecting fire brigade header ( Siamese connection )of 150 mm dia, for supplying water in fire tank complete as per specification no. FF-FA/FMC |
| 487 | Supplying and erecting 300 mm dia 1.5m in height air vessel / tank fabricated from min 5mm thick M.S. sheet complete as per specification no. FF-FFA/ACT |
| 488 | Supplying and erecting 20/25mm dia gun metal air release cock, with necessary G.I. coupling to be fitted on top of air vessel or on wet riser complete as per specification no. FF-FFA/ARV |
| 489 | Supplying and erecting 100 mm dia. pressure gauge , 0-300 PSI or 0-14 kg per cm square fitted with 12/15 mm dia. pad cock valve, erected with provided G.I. pipe, elbow etc. complete as per specification no. FF-FFA/PG |
| 490 | Supplying and erecting 12/15 mm dia pressure switch with provided isolation valve, G.I. nipple, elbow, etc complete as per specification no. FF-FFA/PS |
| 491 | Supplying and erecting M.S./CRCA cabinet for housing single hydrant valve of size ( 400 x 400 x 400)mm or hose pipe box of size ( 600 x 600 x 200)mm made from min. 1.5 mm thick CRCA sheet with angle iron work of min. of size (25 x 25 x 4) mm having front doors with viewing glass of size (200x150) mm and locking arrangement with necessary fixing material such as rubber bidding etc. duly painted in post box red colour( Code 538 of IS 5) |
| 492 | Supplying, installing, testing and commissioning FRLS, XLPE armoured cable 2 core 1.5 sq.mm. copper conductor complete erected on wall/ ceiling complete as per specification no. CB-LT/CU (Fire Cable) |
| 493 | Supplying, installing, testing and commissioning of micro processor based intelligent addressable main fire alarm panel, central processing unit with the 1 loop capacity and capable of supporting upto 250 devices and detectors per loop, with on-board LCD display with min 16 lines of text, operating at 230 V 50 HZ - AC with inbuilt Battery Backup of a minimum 24 hours in normal condition and 30 min in alarm condition, suitable provision for network connectivity, interfacing with third party equipment via a MODBUS/ OPC/ L-ON interface etc. conforming to IS 15908:2021, IS 2189: 2008, EN 54 & VDS / FM/ UL 864 (10th edition) with 3 years replacement warranty FF-AFAS/CP. |
| 494 | Supplying, installing, testing and commissioning of addressable optical smoke detector, single/twin LED’s with 360 degree view, suitable for low voltage 15 to 32 V DC two wires supply, in-built locking mechanism to check the removal and pilferage of the detector, in built isolation mode, start up current 300µA and alarm condition current shall be maximum 6.5 mA, operating temperature 0°C to 50°C, humidity 0-95% RH, IP 41, conforming to IS 2189: 2008, 11360_1985_Reff2020 EN 54 or UL Approved with 3 years equipment replacement warranty FF-AFAS/SD . |
| 495 | Supplying, installing, testing and commissioning of intelligent addressable thermal/heat detector with rate of rise cum fixed temperature thermistor complete with base as required, suitable for temperature variations from -20°C to 38°C for fixed-heat and rate-of-rise type detectors and 0°C to 66°C for high heat type detectors, in built isolation mode, suitable for offices/ceiling cable trenches/less ventilation area's etc. with 3 years equipment replacement warranty IS : 2175 - 1988 reaffirmed 2000, IS 15908:2021 standards FF-AFAS/SD. |
| 496 | Supplying, installing, testing and commissioning of addressable manual call points ( break glass type/pull station type), made of addressable break glass plastic square in shape surface/flush mounted with \\"Break Glass\\" massage embedded on the glass, complete erected with mounting base and required accessories conforming to EN 54 or UL listed with 3 years equipment replacement warranty FF-AFAS/MCP. |
| 497 | Supplying, installing, testing and commissioning of addressable fire control/relay module complete as required, with 3 years equipment replacement warranty conforming to IS 5051Part 2 (Sec 1 to 3) : 1982 reed relays, EN 54 or UL Listed FF-AFAS/CRM |
| 498 | Supplying, installing, testing and commissioning of addressable fire monitor module complete as required. EN 54 or UL Listed with 3 years equipment replacement warranty conforming to IS 5051Part 2 (Sec 1 to 3) : 1982 Reed relays FF-AFAS/MM |
| 499 | Supplying, installing, testing and commissioning of addressable fire isolator module complete as required. EN 54 /FM or UL Listed with 3 years equipment replacement warranty conforming to IS 5051Part 2 (Sec 1 to 3) : 1982 Reed relays FF-AFAS/ISM |
| 500 | Supplying, installing, testing and commissioning of addressable horn cum strobe sound/ hooter, output frequency 500 to 1000 Hz with dB as per Chart given in IS 15908:2021, with flashing at 1 Hz over the strobe’s entire operating voltage range EN 54, conforming to IS 2189: 2008, IS 15908:2021 standards with 3 years equipment replacement warranty FF-AFAS/SSH. |
| 501 | Supplying, erecting, testing and commissioning 15 to 30 Watts sound column or ceiling mounted complete as per specification no. FF-PA/SOC |
| 502 | Supplying, erecting, testing and commissioning of 1.5 sq. mm speaker wire complete. |
| 503 | Supplying, erecting, testing and commissioning of quartzoid bulb sprinkler, 15 mm (½\\") dia. NBCM Body chrome finished, 68º C fixed temperature rating with deflector disc of conventional construction complete as per specification no. FFSPR. |
| 504 | Supplying, erecting, testing and commissioning vane type water flow detector75/80 mm dia. with 1) Visual switch activation 2) Rugged switch assembly 3) Heavy duty aluminium pipe saddles 4)Durable metal enclosure 5) Steel U bolts for secure mounting 6) Two SPDT ( Single pole double track ) synchronised switches 7) serviceable without draining pipes. |
| 505 | Supplying, erecting, testing and commissioning vane type water flow detector 100 mm dia. with 1) Visual switch activation 2) Rugged switch assembly 3) Heavy duty aluminium pipe saddles 4)Durable metal enclosure 5) Steel U bolts for secure mounting 6) Two SPDT ( Single pole double track ) synchronised switches 7) serviceable without draining pipes. |
| 506 | Supplying and erecting fire resistant mortar (20 kg) with fire resistance class S90 as per National Electrical Code (NEC) SP30-2011 suitable to seal the openings of all kinds of cables, pipes and cable support system in steel, aluminium and plastic profiles ( except hollow core conductors). The residual openings shall be closed with filler, as per specification no FF-FRM. |
| 507 | Supplying & erecting Carbon Dioxide (CO2) fire extinguisher of 4.5 kg. capacity cartridge type conform to IS 2878 /15683 complete erected with necessary clamp made from 50 x 6 mm. M. S. flat with nut & bolts routed in wall complete. |
| 508 | Making cement concrete foundation including excavation ( 45 x 45 x 120 ) cm deep in 1:3:6 cement concrete, 20 to 25 mm stone metal, (45 x 45 x 45) cm / 45 cm dia. x 45 cm height plinth duly plastered, with necessary curing and finishing complete. (for 6 m pole) |
| 509 | Making cement concrete foundation in 1:2:4 cement concrete with foundation bolts and nuts complete. (cost of wooden box is included) (for pumps). |
| 510 | Making cement concrete foundation in 1:3:6 cement concrete, (20 to 25) mm. stone metal duly plastered with necessary curing for complete. (pole muffing or any other purpose). |
| 511 | SITC of Electric Traction Passenger Lift with· Rated capacity :- 4 Passenger/272Kg· Floors :- G+1 floor (2 Stops/2 Landings)· Travel :- 3 to 4.2 mtrs· Location of Lift Machine:- MR/MRL· Rated speed :- 1.0 mps VS· Car/Landing door clear opening of 700/800 mm wide x 2000 mm high· Clear Car size of 1100 mm wide x 700 mm deep x 2250mm high· Lift shaft available having clear size of 1500 mm wide x 1500 mm deep, 1500 mm Pit depth, 1580 mm Overhead.· Doors type :- COPO/TOPO Doors with frame made from SS 304 grade solid (non-cladded) sheet of 1.5mm thick in hairline finish for car and all landing doors with SS door architraves/frames. The lift doors shall have minimum 1 hour fire rating (with submission of necessary valid test certificate issued by NABL accredited or Independent test laboratory).· Lift car enclosure made from SS 304 grade solid (non-cladded) sheet of 1.5mm, thick with hairline finish with frame made from MS girders, bracing of adequate size with minimum safety factor of 5, with Toe Guard Apron, with necessary false ceiling with adequate LED lights, blower/fan for ventilation & SS chequered plate flooring, handrails, mirror, emergency light etc. The lift car interior design shall be done as per the directions of engineer in charge.· COP with SS face plate having metallic push buttons with Braille code & luminous indicator around button with FPI, scrolling UP/DN LED indicator & with / without attendant key switch, OWD with audio-visual alarm, VAS in Marathi, Hindi & English with intercom system with telephone instrument in Lift car, LMR & FCC/ground floor.· LOP with SS face plate having recess/surface push button box for all landings with scrolling UP/DN LED indicator having metallic push buttons with Braille code & luminous indicator around button with CPI, Lift car arrival & next travel direction audio-visual indication at all landings.· Lift controller based on microprocessor/ PLC with VVVF Drive having closed loop control system, with IBMS compatible having necessary port. The controller shall have necessary protections such as overcurrent, overvoltage, over speed, overheat for all devices including lift motor and travel direction protection, protection for phase loss at input or output etc. various operation modes such as maintenance, change direction by attendant, full load bypass, VIP call operation, self levelling operation, call cancel facility, auto return to home landing, fireman evacuation operation, earthquake operation, door open/close operation from COP etc. The system can record information for minimum 30 latest faults, with real-time clock management and handheld keypad with LCD screen for view and setting of parameters. The control panel duly wired with proper size & strength, copper wire for power & control circuit, with provision for addition of floor/control card & allied accessories control panel having enclosure of 1.5mm CRCA sheet with powder coating with IP54 Protection class.· ARD complete with necessary SMF VRLA batteries.· Fireman controller having fireman switch at fire Landing.· CCTV surveillance system comprises of 2 nos. minimum 2.0 MP FHD IP based vandal proof Dome camera in lift car & in LMR/inside lift shaft top aimed on lift machinery & controller with NVR kept in LMR/FCC with HDR data backup for min. 90 days with min. 18” FHD TV monitor, to be kept in FCC/LMR as directed by Engineer In Charge.· Lift Machine of Gearless PMSM of suitable kW with duty cycle of minimum 120 starts/hr (with submission of necessary valid test certificate issued by NABL accredited or Independent test laboratory), with Traction pulley, OSG, electromagnetic brakes, entire assembly mounted on adequate size girders duly fixed on LMR floor/ shaft walls complete with main/diverter traction sheaves, suspension wire ropes/belts of adequate size & strength.· Other mechanical parts such as 'T' section adequate size guide rails for car & counter weight with brackets fasteners, counter weight frame with necessary blocks, buffers with necessary support arrangement, MS pit ladder etc. erected with necessary steel work.· Minor civil work such as alteration work if any necessary for erection of landing door frames and it's accessories e.g. sill, header, hole pass etc complete with plaster finish, civil work for erection buffers, erection of lift machinery, adequate size core cuts if required & scaffolding for erecting guide rails, providing and fixing steel girders/RCC work having adequate strength for mounting and hoisting lift machine etc. complete as per specification no. LFT.\\"· General: - Job includes the entire procedure of obtaining all necessary erection permissions & \\"\\"License to Work the Lift\\"\\" from Electrical Inspector(Lifts) with submission to the Engineer In Charge.· The above rate includes Fully Comprehensive AMC for one year from the date of commissioning.\\" |
| 512 | SITC of Electric Traction Passenger Lift with· Rated capacity :- 10 Passenger/680Kg· Floors :- G+1 floor (2 Stops/2 Landings)· Travel :- 3 to 4.2 mtrs· Location of Lift Machine:- MR/MRL· Rated speed :- 1.0mps VS· Car/Landing door clear opening of 800 mm wide x 2000 mm high· Clear Car size of 1350mm wide x 1300 mm deep x 2250mm high· Lift shaft available having clear size of 2220mm wide x 1790mm deep, 1500mm Pit depth, 4800 mm Overhead.· Doors type :- COPO/TOPO Doors with frame made from SS 304 grade solid(non-cladded) sheet of 1.5mm thick in hairline finish for car and all landing doors with SS door architraves/frames The lift doors shall have minimum 1 hour fire rating (with submission of necessary valid test certificate issued by NABL accredited or Independent test laboratory).· Lift car enclosure made from SS 304 grade solid (non-cladded) sheet of 1.5mm, thick with hairline finish with frame made from MS girders, bracing of adequate size with minimum safety factor of 5, with Toe Guard Apron, with necessary false ceiling with adequate LED lights, blower/fan for ventilation & SS chequered plate flooring, handrails, mirror, emergency light etc. The lift car interior design shall be done as per the directions of the engineer in charge.· COP with SS face plate having metallic push buttons with Braille code & luminous indicator around button with FPI, scrolling UP/DN LED indicator & with / without attendant key switch, OWD with audio-visual alarm, VAS in Marathi, Hindi & English with intercom system with telephone instrument in Lift car, LMR & FCC/ground floor.· LOP with SS face plate having recess/surface push button box for all landings with scrolling UP/DN LED indicator having metallic push buttons with Braille code & luminous indicator around button with CPI, Lift car arrival & next travel direction audio-visual indication at all landings. · Fireman controller having fireman switch at fire Landing.· CCTV surveillance system comprises of 2 nos. minimum 2.0MP FHD IP based vandal proof Dome camera in lift car & in LMR/inside lift shaft top aimed on Lift machinery & controller with NVR kept in LMR/FCC with HDR data backup for min. 90 days with min.18” FHD TV monitor, to be kept in FCC/LMR as directed by Engineer In Charge.· Lift Machine of Gearless PMSM of suitable kW with duty cycle of minimum 120 starts/hr (with submission of necessary valid test certificate issued by NABL accredited or Independent test laboratory), with Traction pulley, OSG, electromagnetic brakes, entire assembly mounted on adequate size girders duly fixed on LMR floor/ shaft walls complete with main/diverter traction sheaves, suspension wire ropes/belts of adequate size & strength.· Other mechanical parts such as 'T' section adequate size guide rails for car & counter weight with brackets fasteners, counter weight frame with necessary blocks, buffers with necessary support arrangement, MS pit ladder etc. erected with necessary steel work.· Minor civil work such as alteration work if any necessary for erection of landing door frames and it's accessories e.g. sill, header, hole pass etc complete with plaster finish, civil work for erection buffers, erection of lift machinery, adequate size core cuts if required & scaffolding for erecting guide rails, providing and fixing steel girders/RCC work having adequate strength for mounting and hoisting lift machine etc. complete as per specification no. LFT.\\"· General: - Job includes the entire procedure of obtaining all necessary erection permissions & \\"\\"License to Work the Lift\\"\\" from Electrical Inspector(Lifts) with submission to the Engineer In Charge.· The above rate includes Fully Comprehensive AMC for one year from the date of commissioning. |
| 513 | Supplying & erecting triple pole and neutral PPI distribution board (TPNDB), with 2P RCBO per Phase Isolation and SPMCB of 4 ways/phase (12 poles), with door, 1.2mm thickness, surface/flush mounted, IP 43 protection on iron/GI frame (horizontal busbar type) as per specification no. SW-SWR/MCBDB |
| 514 | Supplying & erecting of Bed side desk lamp with fabric shade and solid wood for Guest bedrooms, Lamp of 15W Base material-Wood, Vintage Style with Operation of Switch Type is Push Button & Rotary, Corded Electric power source, appropriate lux levels to be achieved for the specific use of the space. |
| 515 | Supplying, Erecting, Testing and Commissioning of Cluster type-1 Light Max-150W Fixture for Lobby areas. Item to include provision of hook in the ceiling to take the weight of the chandelier and covering the pipe or rod exposed after suspending the chandelier with a velvet cloth to hide the chain. Item to also include provision of all lamps in the fixture. |
| 516 | Supplying, erecting, testing and commissioning PA Mixer 14 channel With MP3 Player, USB/SD card reader and Bluetooth facility, 48V Phantom Supply on all Channels, Professional mixer with 24 Digital Effects, 2 Group Outputs, 12 MIC and 10 LINE Balanced mono inputs, 2 STEREO Balanced inputs, Mic input - impedance/ gain -2kΩ/65dB, Frequency response 25Hz- 20kHz, impedance- 600Ω ,S/N ratio- >80dB, Operates on 240V 50Hz AC mains, LCD display for viewing the EFFECTS/USB settings, each input channel has a GAIN control, 4 band active Equalizer controls, AUX1, AUX2, AUX3/EFX, AUX4/FX and PAN control with Channel Mute Switch, with Easy and accurate monitoring of Left & Right output levels through individual 12 segment LED array, with 11 preset Equalizer settings & Headphone output with Level Control for output monitoring, complete as per specification no. PA-MXR |
| 517 | Supplying, erecting, testing & commissioning Mixer Amplifier 500W RMS Power with Built-in Digital Player with remote and having 7 Mic & 3 Aux Inputs with Box Speaker/Driver Unit selector witch to each zone , stereo/mono switch, frequency response 50-15000Hz, output regulation <2dB, separate control for USB level. The unit shall have Preamplifier and Line Output for connecting to a Booster Amplifier and for recording the programme with Resettable circuit breaker for protection against overload and short circuit. The unit shall have speaker output range of 2Ω, 4Ω/(Low Impedence) and 70V & 100V/(High Impedence) & It can instant transfer to DC power(36V) if AC power fails. Signal to noise ratio between 60dB to 80dB. Complete as per specification no. PA-MA |
| 518 | Supplying, erecting, testing and commissioning Call Station with built-in monitoring speaker and programmable buttons, Temporary recording function for instant message recording and broadcasting. |
| 519 | Supplying & erecting of High definition 4/5 Megapixel IP IR Dome Camera with following features 4/5MP Vandal Dome Camera. 1/2.7\\"\\" or higher 4MP PS CMOS Image Sensor Max. 4MP (2688 x 1520)@25fps or above /Max. 5MP (2880x1620)@25fps or above Instastream, H.265, H.264, H.264H, H.264B, MJPEG | Support Quad Stream WDR(120dB), Day/Night (ICR), 3D NR, ROI, AWB, AGC, BLC, HLC, Digital watermarking Support Built-in Mic IR Range of 30Mtr or above., Warm Light Range of 30Mtr or above. 3.6mm fixed Lens (2.8mm, 6mm Optional) Support Starlight Technology Micro SD Card upto 256GB Supported, PoE, IP67, IK10 ISO 9001: 2015, ISO 20000-1 : 2018, CE, FCC and RoHS, BIS, STQC ER Certificate, duly erected on wall/ceiling/provided pole with all accessories complete with 3 years warranty. \\" |
| 520 | Supplying & erecting of High definition 4/5 Megapixel IP IR Bullet Camera with following features 4/5 MP Bullet Camera. 1/2.7\\" or higher 4MP PS CMOS Image Sensor Max. 4MP (2688 x 1520)@25fps or above /Max. 5MP (2880x1620)@25fps or above Instastream, H.265, H.264, H.264H, H.264B, MJPEG Support Quad stream WDR(120dB), Day/Night(ICR), 3D NR, ROI, AWB, AGC, BLC, HLC, Digital watermarking IR Range of 30Mtr or above, Warm Light Range of 30Mtr or above. 3.6mm fixed Lens (2.8mm, 6mm Optional) Support Starlight Technology Micro SD Card upto 256GB Supported, PoE, IP67, IK10 ISO 9001: 2015, ISO 20000-1 : 2018, CE, FCC and RoHS, BIS, STQC ER Certificate, duly erected on wall/ceiling/provided pole with all accessories complete with 3 years warranty. |
| 521 | Supplying, installing, testing & commissioning of 16 Ch Network Video Recorder (NVR) 16Ch. 4K Network Video Recorder Up to 16 channel IP camera input Instastream/H.265/Smart H.264+/H.264 codec decoding Up to 8MP resolution preview and playback Max. 200Mbps incoming bandwidth Support 2 SATA HDDs up to 20TB Each, 2 USB Ports (1 front USB 2.0 port, 1 rear USB 3.0 port) HDMI/ VGA Heterogeneous video output Support Multi-brand network cameras RoHS, UL, CE, FCC certified. duly erected in provided U Rack with wiring connections, tagging and programming etc. complete as per specifications no. CCTV-NVR complete with 3 years warranty. |
| 522 | Supplying, installing, testing & commissioning of 32 Ch Network Video Recorder (NVR) 32Ch. 4K AI Network Video Recorder Up to 32 channel IP camera input Max. 256 Mbps incoming/recording/outgoing bandwidth Instastream/H.265/Smart H.264+/H.264/MJPEG codec decoding Up to 12MP resolution preview and playback AI by Recorder: 2-channel face detection or recognition/ 4-channel perimeter protection/ 8- channel SMD Plus, AI by Camera: supports face detection and recognition, perimeter protection, SMD Plus, metadata, ANPR, stereo analysis, heat map, and people counting Support 4 SATA HDDs up to 16TB Each, 3 USB Ports (2 USB 3.0) 2 HDMI/ 2 VGA simultaneous video output Support Multi-brand network cameras RoHS, UL, CE, FCC certified. Duly erected in provided U Rack with wiring connections, tagging and programming etc. complete as per specifications no. CCTV-NVR complete with 3 years warranty. |
| 523 | Supplying & erecting 43\\" professional LED display with 1920*1080 (Full HD) Display, suitable for 16/32 channel NVR and following features - Brightness: minimum 500 Cd/m2 | Contrast Ratio: minimum 1000:1 | Viewing angle: 178/178 deg. | Response time: maximum 8 ms | Inputs: HDMI, VGA, BNC,USB, Audio In, | Built-in speakers maximum 10 W, | Suitable to operate on 100-240 V 50 Hz AC supply and 24/7 Duty Cycle duly erected on wall or table top with standard accessories like wall mount stand and wiring connections etc. complete as per specifications no. CCTV-Monitor, complete with 1 years warranty. |
| 524 | Supplying & erecting 8 TB internal Surveillance HDD suitable for SATA Port of NVR, interface transfer rate 6 GB/S, maximum sustained transfer rate 210 MB/Sec to 213 MB/S. Drive bay supported 08+, Cameras supported up to 64, Cache (MB) 256, Load/Unload Cycle -3000000, Work Load Rating per Year 180TB, MTBF 1000000 Hrs. HTTPS. RoHS, UL, CE certified, duly erected in position in provided NVR as per specifications CCTV-HDD complete with 3 years warranty. |
| 525 | Supplying & erecting 32\\" professional LED display with 1920*1080 (Full HD) Display, suitable for 16 channel NVR and following features Brightness: minimum 250 Cd/m2 Contrast Ratio: minimum 1000:1 Viewing angle: 178/178 deg. Response time: maximum 8 ms Inputs: HDMI, VGA, BNC, USB, Audio In, Built-in speakers maximum 2 W, Suitable to operate on 100-240 V 50 Hz AC supply and 24/7 Duty Cycle duly erected on wall or table top with standard accessories like wall mount stand and wiring connections etc. complete as per specifications no. CCTV-Monitor, complete with 1 years warranty. |
| 526 | Supplying & erecting of High definition 2 Megapixel IP IR Dome Camera with following features 2MP Vandal Dome Camera. 1/2.7\\" or higher 2MP PS CMOS Image Sensor Max. 2MP (1920 × 1080)@25fps or above Instastream, H.265, H.264, H.264H, H.264B, MJPEG Support Quad Stream WDR(120dB), Day/Night(ICR), 3D NR, AWB, AGC, BLC, HLC, Digital watermarking IR Range of 30Mtr or above, Warm Light Range of 30Mtr or above. 3.6mm fixed Lens Support Starlight Technology Built-in Mic, Micro SD Card upto 256GB Supported, PoE, IP67, IK10 MTBF Certificate from STQC, EMI/EMC, ISO9001, CE, FCC and RoHS, BIS, STQC ER Certificate, duly erected on wall/ceiling/provided pole with all accessories complete with 3 years warranty. |
| 527 | Supply installation, testing & Commissioning of Windows PC: 60.5cm (23.8) All-in-One Desktop PC with features: 13th Generation intel Core TM 17 processor, windows 11 Pro, 60.5cm (23.8) diagonal FHD ips display, intel UHD Graphics 770, 3200 RAM, 1 TB SSD Hard drive, complete. |
| 528 | Supplying and erecting G.I. pipe ‘C’ class ERW 32 mm dia with necessary fittings complete as per specification no. FF-PP |
| 529 | Supplying and erecting COB light of 8.0 W Operating Temperature -10°C to 40°C Rated Input Voltage & Frequency 230 VAC, 50Hz Rated Input Wattage 8W ± 10% Rated Input Current 0.033 Amp (Nominal) Power Factor ≥0.90 ATHD <10% Rated Luminous Flux 600 lm / 560 lm / 520 lm (For 24°) (tolerance as per BIS) Rated Luminaire Efficacy 75 lm/W / 70 lm/W / 65 lm/W (tolerance as per BIS) Correlated Color Temperature (CCT) 4000 K / 3000 K / 2700 K (tolerance as per ANSI) Color Rendering Index (CRI) >90 Ra Beam Angle Available in 15° / 24° / 36° (within the permissible limits) Driver Efficiency ≥75% (Flicker Free) LED Life Span >50000 Hrs (Ta=25°C @L70) Housing Die Cast Aluminium. |
| 530 | Supplying and erecting COB DownLight 15.0 W Operating Temperature -10°C to 40°C Rated Input Voltage & Frequency 230 VAC, 50Hz Rated Input Wattage 15W ± 10% Rated Input Current 0.068 Amp (Nominal) Power Factor ≥0.90 ATHD <5% Rated Luminous Flux 1200 lm / 1125 lm / 1050 lm (For 24°) (tolerance as per BIS) Rated Luminaire Efficacy 80 lm/W / 75 lm/W / 70 lm/W (tolerance as per BIS) Correlated Color Temperature (CCT) 4000 K / 3000 K / 2700 K (tolerance as per ANSI) Color Rendering Index (CRI) >90 Ra Beam Angle Available in 24° / 36° / 50° (within the permissible limits) Driver Efficiency ≥75% (Flicker Free) LED Life Span >50000 Hrs (Ta=25°C @L70) Housing Die Cast Aluminium. |
| 531 | Supplying and erecting Dali Dimmers for COB lights DALI-2 + pushDIM Dimming 16 level current output by external DIP Switch | Dimming range : 1-100%, Output current accuracy 2%| Soft dimming & flicker-free at any brightness | Screw-free & Pressing type Strain relief | Intelligent LED hot-plug protection function | CE, DALI-2 Certification | 10W/18W/22W/28W/42W/60W |
| 532 | Supplying and erecting hanging light of glass rectangular shape for Auditorium main entrance area with MS framework and fabric around central acrylic light box of Size of 3m x 2m lux level of 250 lux to be achieved. Minimum 6 lamps of 12 watt each. Item to include provision of hook in the ceiling to take the weight of the chandelier and covering the pipe or rod exposed after suspending the chandelier with a velvet cloth to hide the chain. Item to also include provision of all lamps in the fixture. |
| 533 | Supplying, Installing, Testing & Commissioning of CE Certified 100W LED PARCAN Light with latest RDM technology for user friendly operation with below specifications: • Light Source : Single COB LED Source • Color Temperature : 3200K with CRI & TLCI Value > 90 • Power cable: 3 core 1 sq. mm. copper PVC insulated • Channels: 1/2 DMX-512 Channel Modes • Beam angle: 9°/15°/20°/25°/30° Manually Selectable • Control mode: RDM, DMX512 & Manual, Master/Slave, Auto run • Fully RDM Compliant in DMX Mode for the Lighting Console mentioned in this project. • LUX @ 2m: > 36,000 @ 9° Beam Angle • Dimming: 0 - 100% Electronic Dimming • Function: Strobe, Dimming • Housing : Spun Aluminium Housing with black epoxy polyester powder coated finish. • Accessory slot for Gel frame should be available or else fixture will be rejected. • Power and DMX: Loop in and loop out compulsory • DMX in & Out Through : 5 Pin XLR connectors • Certification: CE / BIS • Accessories : C clamp, Safety bond and Identification name plate. |
| 534 | Supplying, Installing, Testing & Commissioning of CE Certified 400W LED Blinder Effect Light with latest RDM technology for user friendly operation with below specifications: • Light Source : Quad LED COB Source • Power Factor : >0.95 @ 230V AC 50Hz • Color Temperature : 3200K, CRI & TLCI Value > 95 • Power cable: 3 core 1 sq. mm. copper PVC insulated • Channels: 4/8 DMX-512 Channel Modes • Beam Angle : 40° • Control mode: RDM, DMX512 & Manual, Master/Slave, Auto run • Fully RDM Compliant in DMX Mode for the Lighting Console mentioned in this project. • Lux output at 2 Mtr : > 8,500 Lux @ 40° • Dimming: 0 - 100% Electronic Dimming • Power and DMX: Loop in and loop out compulsory • DMX in & Out Through : 5 Pin XLR connectors • Certification: CE / BIS • Accessories : C clamp, Safety bond and Identification name plate. |
| 535 | Supplying, Installing, Testing & Commissioning of CE Certified 54 x 3W LED PAR Light with latest RDM technology for user friendly operation with below specifications: • Base Color RGBW Color Mixing • LED Configuration : Multiple Nos Individual RGBW LED Configuartion • Power cable: 3 core 1 sq. mm. copper PVC insulated • Channels: 8 DMX-512 • Beam angle: 15° • Control mode: RDM, DMX512 & Manual, Master/Slave, Auto run, Sound Active • Fully RDM Compliant in DMX Mode for the Lighting Console mentioned in this project. • LUX @ 2m: >10,500 @ 15° Beam Angle• Dimming: 0 - 100% Electronic Dimming • Function: strobe, dimming, sound active and Master slave. • Housing: Die Casted Aluminium or Metal Housing with black epoxy polyester powder coated finish. • Power and DMX: Loop in and loop out compulsory • DMX in & Out Through : 5 Pin XLR connectors • Certification: CE / BIS • Accessories : C clamp, Safety bond and Identification name plate. |
| 536 | Supplying, Installing, Testing & Commissioning of CE Certified 200W LED Profile Spot Light with latest RDM technology for user friendly operation with below specifications: • Light Source : Single LED COB Source • Color Temperature : 3200K, CRI & TLCI Value > 95 • Power cable: 3 core 1 sq. mm. copper PVC insulated • Channels: 1/2/3 DMX-512 Channel Modes • Beam Angle : 19° or 15° • Control mode: RDM, DMX512 & Manual, Master/Slave, Auto run • Fully RDM Compliant in DMX Mode for the Lighting Console mentioned in this project. • Lux output at 2 Mtr : > 20,000 Lux @ 19° or 15° • Dimming: 0 - 100% Electronic Dimming • 4 Beam shaping shutters • Accessory slot for Gobo and gobo holder, Iris & Color Frame should be available or else fixture will be rejected. • Housing: Metal Housing with black epoxy polyester powder coated finish or PVC Body with matt black finish • Power and DMX: Loop in and loop out compulsory • DMX in & Out Through : 5 Pin XLR connectors • Certification: CE / BIS • Accessories : C clamp, Safety bond and Identification name plate. |
| 537 | Supplying, Installing, Testing & Commissioning of CE Certified 54 x 3W LED PAR Light with latest RDM technology for user friendly operation with below specifications: • Base Color 3200K Color Mixing • Color Temperature : 3200K with CRI > 90 • LED Configuration : Multiple Nos Individual 3200K LED Configuartion • Power cable: 3 core 1 sq. mm. copper PVC insulated • Channels: 1 DMX-512 • Beam angle: 15° • Control mode: RDM, DMX512 & Manual • Fully RDM Compliant in DMX Mode for the Lighting Console mentioned in this project. • LUX @ 2m: >7,500 @ 15° Beam Angle • Dimming: 0 - 100% Electronic Dimming • Function: strobe, dimming, sound active and Master slave. • Housing: Die Casted Aluminium or Metal Housing with black epoxy polyester powder coated finish. • Power and DMX: Loop in and loop out compulsory • DMX in & Out Through : 5 Pin XLR connectors • Certification: CE / BIS • Accessories : C clamp, Safety bond and Identification name plate. |
| 538 | Supplying, Installing, Testing & Commissioning of CE Certified 150W LED HYBRID MOVING (Beam, Spot & Wash Effect ) Light with RDM protocol and Hi grade plastic body black color with following specifications - • LED : 150W Cool White LED. • Beam Angle : 3°~4°, Zoom Angle : 8°~15° • Power Consumption : 150W ± 10% • Light Out put : >20,000 Lux at 2 Mtrs • Color Wheel : Minimum 8 Colors and open or More• Fixed Gobo Wheel : Minimum 9 Fixed Gobos or More • Rotating Gobo wheel : Minimum 7 Rotating Gobos or More • User Interface : 4 Nos High Precision Membrane type selector switch with LCD Display • Fully RDM Compliant when in DMX mode • Dimming : 0 to 100% 16 Bit Linear Dimming • DMX data IN / OUT: 5 pin locking XLR • Cooling system with low noise fan for forced ventilation • 3 Mtr 3 core 1 mm² FRLS & ISI mark cable with 3pin IEC Male Plug with proper earthing • 3 mtr DMX loop cable with cable mount 5 pin locking XLR • CE Certificate should be enclosed to ensure the required quality and safety of the products.• Accessories : C clamp, Safety bond and Identification name plate. |
| 539 | Supply, Installation, Testing & Commissioning of Fixed Stage Light Bar, length 7 to 8 Mtrs made using MS 40NB Class ‘B’ Pipe dual barrel construction arrangement undergone through various chemical treatment to keep them rust free and duly epoxy polyester powder coated in black matt texture finish with Below Specifications: • Dual barrel Light bar equipped with 40x75x40 Cable trenching arrangement with lid for better aesthetic look and cable safety. • Frill Bar attachment.• Dual barrel pipe construction welded with 75x6mm MS Flat in every 1 Mtr for better strength • With Suitable Suspenders to fix the light bar with every 2mtr pitch. |
| 540 | Supply, Installation, Testing & Commissioning of Fixed FOH Stage Light Bar, length 9 Mtrs made using MS 40NB Class ‘B’ Pipe dual barrel construction arrangement undergone through various chemical treatment to keep them rust free and duly epoxy polyester powder coated in black matt texture finish with Below Specifications:• Dual barrel Light bar equipped with 40x75x40 Cable trenching arrangement with lid for better aesthetic look and cable safety. • Dual barrel pipe construction welded with 75x6mm MS Flat in every 1 Mtr for better strength • With Suitable Suspenders to fix the light bar with every 2mtr pitch. |
| 541 | Supply, Installation, Testing & Commissioning of MS Side Lighting Ladder of suitable length and Width (Min 2400 mm Height & 600 mm Width) • Made using 40NB, 48MM OD, 2mm thickness MS Pipe • Suitable suspender and clamps made with MS Angle of size 40x40x5 mm thick or higher size • Inverted 4-Wheeler Trolley with Flexi Adaptor Clamp, • Heavy duty Ladder Track to be laid throughout the depth of the stage. • 360° Rotatable and can move in unidirectional • All the materials under gone through 7 tank process with various chemical treatment to keep them rust free with and duly epoxy polyester powder coated in black matt texture finish. |
| 542 | Supply, Installation, Testing & Commissioning of MS Fabricated 4 way 10A, 250V A.C, IEC, Lighting Junction box made up of 22SWG CRCA for LED lighting fixtures with Pipe clamp arrangement for fixing on pipe grid or Raul plug arrangement for wall/floor fixing, duly black epoxy polyester powder coated texture finish. |
| 543 | Supply, Installation, Testing & Commissioning of MS Fabricated 2 way 10A, 250V A.C, IEC, Junction box made up of 22SWG CRCA with rocker switch to power up splitter and console with Pipe clamp on pipe grid arrangement for fixing or Raul plug arrangement for wall/floor fixing, duly black epoxy polyester powder coated texture finish. |
| 544 | Supply, Installation, Testing & Commissioning of MS Fabricated 5 pin DMX Signal IN Junction box fitted with 5 pin DMX Male socket, junction box made up of 22SWG CRCA, with Pipe clamp on pipe grid arrangement for fixing or Raul plug arrangement for wall/floor fixing, black epoxy polyester powder coated, duly black epoxy polyester powder coated texture finish. |
| 545 | Supply, Installation, Testing & Commissioning of MS Fabricated 5 pin DMX Signal OUT Junction box fitted with 5 pin DMX female socket, junction box made up of 22SWG CRCA, with Pipe clamp on pipe grid arrangement for fixing or Raul plug arrangement for wall/floor fixing, black epoxy polyester powder coated, duly black epoxy polyester powder coated texture finish. |
| 546 | Supply, Installation, Testing & Commissioning of Well designed 15 Way Direct Lighting Distribution Board made up of CRCA sheet undergone through 7 tank process with various chemical treatment to keep them rust free, duly powder coated with Matt texture finish consists of R, Y, B Indicator lamp, 32A TPN incomer, SP Mcb's and for the junction boxes fixed on the top of the light bar including wiring and busbar connection with proper earthing and Hingable door with magnetic door lock complete. |
| 547 | Supply, Installation, Testing & Commissioning of Fabricated 5 pin DMX Signal loop Junction box fitted with 5 pin DMX Male & Female socket with 0.3 Mtr DMX Loop cable fitted with 5 pin DMX cable mount plug, junction box made up of 22SWG CRCA, with Pipe clamp on pipe grid arrangement for fixing or Raul plug arrangement for wall/floor fixing, black epoxy polyester powder coated, duly black epoxy polyester powder coated texture finish. |
| 548 | Supply, Installation, Testing & Commissioning of Auxiliary marshalling box for power and signal cable termination in grid level and in Motorised Light bar • CE Marked FC/PG cable entry gland required Nos as per cable entry. • MS channel arranging to fix terminal connector, required nos with separation plate and each end is completed with adding end plate with end cap. • Grey terminal connector with each line having P, N, E Indication for each line incoming and out going cable connectors. • Box door must be made with Hingeable door with screw lock. • Made up of 20SWG CRCA sheet undergone through 7 tank process with various chemical treatment to keep them rust free, duly epoxy polyester powder coated with Matt black texture finish. |
| 549 | Supply, Installation, Testing & Commissioning of RDM Compatible DMX Splitter unit with Minimum following specifications. ● 1 Nos 5 Pin DMX In socket and 8 Nos 5 Pin DMX Out socket ● In and out signal Optically Isolated ● LED Indicator for check the signal flow in output.●Suitable for standard 19” cabinet ● Duly black epoxy polyester powder coated texture finish. |
| 550 | Supply, Installation, Testing & Commissioning of Digital Lighting Console with Ultimate portability, offering a powerful LED and moving light controller in a small 19” unit with direct access to each of the lights. • 1024 DMX Channel • LDC Screen for easy Navigation • DMX compatible• Control up to 96 LED, moving lights and conventional individuals• multi-function faders |
| 551 | Supply, Installation, Testing & Commissioning of 5 pin XLR male / female connectors of made up of Extra high temperature resistant insulator material, Larger solder contacts for easier termination. |
| 552 | Supply, Installation, Testing & Commissioning of 5 Pin XLR Termination plug made up of extra high temperature resistant insulator material, Larger solder contacts for easier termination with 120 Ohm resistor with 0.25Watt for signal termination. |
| 553 | Supply, Installation, Testing & Commissioning of FR Grade DMX Signal 4 core + Ground shielding Cable with CE mark for the Signal network. |
| 554 | Supply, Installation, Testing & Commissioning of MS perforated tray of Size 40 x 75 x 40mm & 1.6 mm Thickness undergone through 7 tank process with various chemical treatment to keep them rust free, duly epoxy polyester powder coated with Matt black texture finish along with clamping arrangement. |
| 555 | Supply, Installation, Testing & Commissioning of Internal earthing copper bare conductor of size 14 SWG for power network related to work coming under our scope. |
| 556 | Supply, Installation, Testing & Commissioning of Installation hardware’s such as clamps, connectors, glands, lugs, ferrules, welding rods and miscellaneous items required during installation work. |
| 557 | Supply, Installation, Testing & Commissioning of Main Valance Bar, length 12 Mtrs made using 40NB, 48mm OD construction arrangement 2mm Thickness undergone through various chemical treatment to keep them rust free and duly epoxy polyester powder coated in black matt texture finish with suitable suspenders. • Cost of fabric not included. |
| 558 | Supply, Installation, Testing & Commissioning of Main Curtain track system 12 Mtrs long, center parting with overlap of 0.9mtr arrangement undergone through various chemical treatment to keep them rust free and duly epoxy polyester powder coated in black matt texture finish with Below Specifications: • Heavy duty curtain track duly epoxy polyester powder coated in black matt texture finish. • 1.5 HP Motor, 3 Phase Motor. • GI wire ropes with steel core at center. • Curtain holding trollies placed uniformly at specific interval of 200mm /250 mm throughout the track. • Diverter pulley • MS yellow passivized Routing pulleys with ball bearing for smoother noiseless movement 165mm for outer diameter, 145mm diameter at groove base with 12mm pulley thickness. • All the materials under gone through 7 tank process with various chemical treatment to keep them rust free with and duly epoxy polyester powder coated in black matt texture finish. • Cost of fabric not included. |
| 559 | Supply, Installation, Testing & Commissioning of Rear Curtain track system 9 Mtrs long, center parting with overlap of 0.9mtr arrangement undergone through various chemical treatment to keep them rust free and duly epoxy polyester powder coated in black matt texture finish with Below Specifications: • Heavy duty curtain track duly epoxy polyester powder coated in black matt texture finish. • 1.5 HP Motor, 3 Phase Motor. • GI wire ropes with steel core at center. • Curtain holding trollies placed uniformly at specific interval of 200mm /250 mm throughout the track. • Diverter pulley • MS yellow passivized Routing pulleys with ball bearing for smoother noiseless movement 165mm for outer diameter, 145mm diameter at groove base with 12mm pulley thickness. • All the materials under gone through 7 tank process with various chemical treatment to keep them rust free with and duly epoxy polyester powder coated in black matt texture finish. • Cost of fabric not included. |
| 560 | Supply, Installation, Testing & Commissioning of MS, Wing frame made out of 25X25mm or higher size made of MS square pipe with 2mm in thickness undergone through various chemical treatment to keep them rust free and duly powder coated in black matt texture finish with Below Specifications: • Wing Frame Size 4.2 x 1.5 Mtr • 1.5meter wing track of 48x84mm with grid mount brackets made of 40X50X40mm C track,• Pivotable 4 wheeled suspension trolley,• Adjustable floor locking screw jacks with rubber grips, • Inverted 4-Wheeler Trolley with Flexi Adaptor Clamp, • Heavy duty wing track to be laid for minimum length of 1.5mtr, along the width of the stage. • 360° Rotatable and can move in unidirectional • All the materials under gone through 7 tank process with various chemical treatment to keep them rust free with and duly epoxy polyester powder coated in black matt texture finish.• Cost of fabric not included. |
| 561 | Supply, Installation, Testing & Commissioning of Motor Cable Termination box for power cable termination at grid level.• CE certified FC/PG 11 & 13.5 cable entry gland required Nos as per cable entry. • MS channel arranging to fix grey terminal connector, required nos with separation plate and each end is completed with adding end plate with end cap. • Grey terminal connector with each line having L1, L2, L3, E, 6 , 2 , 4 Indication for each line incoming and outgoing cable connectors (L1, L2, L3, E for Power supply & 6 , 2 , 4 for Limit Switch connection)• Box door must be made with Hingeable door with screw lock. • Grid mount fixing arrangement for fixing on grid or Anchor fastener for wall/floor fixing • MS Box made up of 20SWG CRCA sheet undergone through 7 tank process with various chemical treatment to keep them rust free, duly epoxy polyester powder coated with Matt black texture finish. |
| 562 | Supply, Installation, Testing & Commissioning of MS Fabricated Combined 2 Way Motor Control Center panel cum Remote Control panel for Curtain system made up of 14SWG / 16SWG / 18 SWG CRCA sheet undergone through 7 tank process with various chemical treatment to keep them rust free, duly epoxy polyester powder coated with Matt seaman’s grey texture finish with following specifications.• 16A TP or TPN Incomer. • Main Contactor of 9A 240V 4 pole contactor with 04 -06A Over Load relay for safety • 24V 4 pole Low Voltage Contactors • 240V / 24 V Step-down transformer for Low voltage Contactors • All the FRLS PVC ISI Marking cables inside the panel routed through PVC gray color cable trough. • Red Color Mushroom head push button for emergency stop • Yellow color reset push button • Master sector actuator switch with 3 Position UP, DOWN & OFF • Spring return selector switch for each hoist with UP & DOWN indication. • All the cables inside the panel routed through PVC gray color cable trough. • Panel Including wiring with proper earthing. |
| 563 | Supply, Installation, Testing & Commissioning of PVC Copper unarmoured flexible FRLS insulated multicore cable 1100V grade confirming to IS694 size 7cx1.5 sq mm. |
| 564 | SITC of LR FOH Passive 15\\" 2-way full range loudspeaker. Component : 1 x 15\\" LF Driver & 1 x 1\\" HF driver or better Power Handling : RMS- 550W or better Impedance: 8 Ohms Frequency Range : 40 Hz - 20 kHz Dispersion (HxV) : 80 x 30 degree or better Maximum SPL: Peak - 139dB or better System Sensitivity : 99 dB or better Enclosure : Plywood | Multiple rigging point for flying hardware Complete with Custom Mounting arrangements for Speaker required as per site |
| 565 | SITC of Under Balcony Fill Speaker 2 way Full range 8\\" passive Loudspeaker Component : 1 x 8\\" LF Driver & 1 x 1\\" HF driver or better Power Handling : RMS- 250W or better Impedance: 8 Ohms Frequency Range : 50 Hz - 20 kHz Dispersion (HxV) : 80 x 30 degree or better Maximum SPL: Peak - 130dB or better System Sensitivity : 95 dB Enclosure : Plywood | Multiple rigging point for flying hardware Complete with custom mounting arrangement for speaker required as per site |
| 566 | SITC of Upper Balcony Fill Speaker 2 way Full range 8\\" passive Loudspeaker Component : 1 x 8\\" LF Driver & 1 x 1\\" HF driver or better Power Handling : RMS- 250W or better Impedance: 8 Ohms Frequency Range : 50 Hz - 20 kHz Dispersion (HxV) : 80 x 30 degree or better Maximum SPL: Peak - 130dB or better System Sensitivity : 95 dB Enclosure : Plywood Multiple rigging point for flying hardware Complete with custom mounting arrangement for speaker required as per site |
| 567 | SITC of Stage front Fill Speaker 2-way full range Passive loudspeaker system Speaker Type: 2-way full range Passive loudspeaker Component : 8\\"LF driver, 1\\"HF driver Power Handling: 150 W continuous or better Impedance : 4 ohms or better Frequency Range: 58 Hz - 20 Hz Dispersion : 70° (H) x 70° (V) Maximum SPL : 119 dB peak or better System Sensitivity : 91dB or higher Enclosure : Plywood Complete with Mounting bracket required as per site |
| 568 | SITC of Single 18\\" Reflex Loaded Subwoofer Driver : 18\\" LF driver or better configuration Nominal dispersion: OmniPower Handling : 1000 Watt continuous or better Impedance : 8 ohms Frequency Range : 35Hz-200Hz or better Sensitivity: 96 dB or better Maximum Peak SPL : 138 dB or better Flying hardware: M10 x 16 Points or better Enclosure : min. 18 mm birch plywood. Finish PU Semi matt black paint Grille: Powder coated perforated steel, cloth wrapped. Complete with Ceiling suspended/ hung arrangement/ Floor Mounted in Stage Wall as per the site |
| 569 | SITC of Stage Monitor Speaker - 2 way co-axial active speaker 12\\" LF ,1\\" HF Driver Coaxial Design Rated Power 1000 Watt or better Class-D Amplifier Frequency Range (-10 dB) : 65 Hz – 20 kHz or better Maximum SPL 125 dB peak or better 60-80 degree Horizontal x 40-50 degree Vertical Dispersion Birch Plywood construction |
| 570 | SITC of Green Room Speaker - 4\\" Coaxial Surface-Mount Loudspeaker Driver size: 4\\" or better LF RMS Power : 25 W or better Transformer Tap 70V/100V: up to 25 W Impedance : 8 Ohms Frequency Range (-10 dB): 70 Hz - 20 kHz or better Sensitivity: 82 dB or Better Maximum SPL : Peak - 102dB or higher Dispersion: 90 x 60 degrees or better. Complete with Yoke bracket. |
| 571 | SITC of Control Room Speaker - 5\\" Bi-Amped Compact Reference Monitor for control room Active Control Room Monitor Speaker Driver : 5\\" LF and 1\\" HF or better Power Handling : 75W (LF/Mid Range : 50 Watts, HF 25 Watts) or better Max SPL 108dB or better Frequency Response 49 Hz to 20 kHz or better THD < 0.7 % Balanced XLR input and unbalanced 1/4\\" TS input for maximum flexibility MDF cabinet with injection moulded front baffle construction |
| 572 | SITC of Dual channel 3000Watt power amplifier with DSP for Main FOH speaker Class D Type Per channel Power output : 2 × 1000 W @ 2 Ohms, 2 x 1500 W @ 4OhmsTHD 20Hz-20kHz at 1 W <0.1% Signal To Noise Ratio >90 dB Channel separation at 1 kHz >75 dB Frequency Response : 20 Hz to 20 kHz Input impedance 10 kΩ unbalanced, 20 kΩ balanced Internal Sample rate 96 kHz Distortion,1/8 rated power < 0.1% Display LCD 128 x 32, White text on black background Integrated DSP – 20 total presets, user-definable, 8-band parametric, 2-band,dynamic equalizer, Delay 0 – 300 ms, Crossover function 3 filter types, up to 48 dB/oct.Amplifier protection Thermal and DC protection, Rail sensing and peak current limiting. |
| 573 | SITC of Dual-channel Class D 2400Watt power amplifier for Under & Upper Balcony speaker | Nos. of Channel : 2 |Power Handling : 2 x 1200 W @ 4Ohms | THD 20Hz-20kHz at 1 W <0.1% |Signal To Noise Ratio >104 dB or higher Channel separation at 1 kHz >80 dB |Frequency Response : 20 Hz to 20 kHz |Distortion: 0.1% |Display LCD 128 x 32 Inputs / link 2 x XLR | Shall have Integrated Built-in DSP functions such as Delay, EQ, FIR, Adjustable high & low pass filter, Crossover etc. Amplifier circuit protection Controlled start and shutdown behaviour, DC-fault protection |
| 574 | SITC of Dual-channel 7000Watt Power amplifier for Subwoofer - Technology: Class D | Power Handling : 2 × 3500 W @ 2 Ohms, 2 x 2800 W @ 4Ohms, 2 × 1400 W @ 8 ohms | Max power per channel bridge mode 6500 watts @ 4 ohms and 5500 watts @ 8 ohms | Amplifier Gain selectable from 23dB to 44 dB | THD 20Hz-20kHz at 1 W <0.1% | Signal To Noise Ratio >110 dBA | Channel separation at 1 kHz >70 dB | Frequency response : 20 Hz - 20 kHz |Peak output Voltage 155V with Max output current up to 59Amps | Front-panel indicators : Voltage Peak Limiter (VPL); Current Peak Limiter (CPL); Very High Frequency (VHF); High temperature; Fault; Mute | Monitoring and control of key functions accessible via the intuitive Device Control software and the robust, daisy-chained Nomad Link network | Protection and warning – Excessive output current, DC, high temperature, very high frequency , short circuit, open load, mains fuse protection, and soft start. |
| 575 | SITC of Dual channel 800Watt power amplifier for Front Fill speaker - Amplifier Type: Class D | Nos. of Channel : 2 |Power Handling : 2 x 400W @ 2 / 4 / 8 Ohm & 70V | THD 20Hz-20kHz at 1 W <0.1% | Signal To Noise Ratio >106 dB | Channel separation at 1 kHz >70 dB | Frequency Response : 20 Hz - 20 kHz |Asymmetric Power Loading |Comprehensive circuit protection and fault indication |
| 576 | SITC of Dual Channel 120Watts Power amplifier for Green Room Speaker - Class D | Nos. of Channel : 2 | Power output : 2 × 60 W @ 4 ohms, 8 ohms, 70 /100 V | Distortion, 1/8 rated power <0.05% | THD 20Hz-20kHz at 1 W <0.5% or better | Signal To Noise Ratio: >97 dBA or higher | Channel separation (Crosstalk) >85 dBA |High-pass filter 80 Hz HPF |Frequency Response : 20 Hz to 20 kHz |Energy Star Rated |
| 577 | SITC of UHF Wireless handheld microphone system - Cardioid dynamic, Receiving System : True Diversity, Modulation mode : FM, Frequency Response : 100 Hz to 15 kHz , RF Sensitivity: 20 dBuV at 60 dBA S/N ratio (50Ω termination), Total Harmonic Distortion: <1% or better, Dynamic Range > 110dB, switch function : Mute/ Unmute, Operating range: 100 mtrs. or better, RF Power Output High: 30 mW, Low: 10 mW (switchable), No. of Channel : 10 channels per band, Maximum Output level XLR / Balanced: +9 dBV, Balanced audio output attenuator, Accessories Included: detachable Antennas, Rack mount kit |
| 578 | SITC of UHF Wireless Lapel microphone system - Cardioid Condenser, Receiving System :True Diversity, Modulation mode :FM, Frequency Response : 100 Hz to 15 kHz, RF Sensitivity: 20 dBuV at 60 dBA S/N ratio (50Ω termination), Total Harmonic Distortion: <1% or better , Dynamic Range > 110dB, switch function : Mute/ Unmute , Operating range:100 mtrs. or better, RF Power Output High:30 mW, Low: 10 mW (switchable), No. of Channel :10 channels per band, Maximum Output level XLR / Balanced: +9 dBV , Balanced audio output attenuator , Accessories Included: detachable Antennas, Rack mount kit |
| 579 | SITC of UHF Wireless Headworn Microphone system with beltpack transmitter - Omnidirectional Condenser, Receiving System : True Diversity Modulation mode : FM, Frequency Response : 100 Hz to 15000 Hz, RF Sensitivity: 20 dBuV at 60 dB S/N ratio (50 ohms termination), Total Harmonic Distortion: 1 % or better, Dynamic Range 110 dB or higher, switch function : Mute/ Unmute , Operating range: 100 mtrs. or better, RF Power Output High: 30 mW, Low: 10 mW (switchable), No. of Channel : 10 channels per band, Microphone Terminated with 55\\" cable and locking 4-pin connector, Maximum Output level XLR / Balanced: +9 dBV , Balanced audio output attenuator , Accessories Included: detachable Antennas, Rack mount kit |
| 580 | SITC of Antenna distribution system - UHF (wide-band 440-900 MHz) active unity-gain diversity system Enables one pair of antennas to feed Four wireless systems Each distribution system must have identical independent 1-in by 4-out sections each providing a single antenna input, four isolated protected RF outputs and 1 cascade output Interconnection of the units in a cascade fashion for an expanded system must be possible All RF connections shall be rear panel mounted using standard BNC-type connectors 12V DC power to each antenna input to operate powered antennas or in-line RF devices up to 100 mA minimum. Accessories Included: Rack mount kit & BNC cable x 8 Shall supplied from the same OEM |
| 581 | SITC of Pair of UHF wide-band directional LPDA (log periodic dipole array) / Omni antennas | Operating Bandwidth : 470-990 MHz | Antenna Type : LPDA (log periodic dipole array) / omni antennas | Impedance : 50 Ohms Typical | Gain : 6 dB Typical | Enhanced signal pickup for UHF wireless systems | Must have High-quality, low-loss BNC connectors to minimize RF cable strain | Mounts should allow for vertical tilt adjustment through a 90°range | Horizontal adjustment should be possible by rotating the antenna in the mounting fitting. Shall supplied from the same OEM |
| 582 | SITC of RF antenna cable with BNC to BNC connectors, RG8-type cable. 100 m. The cables are constructed of a flexible low loss RG8-type coaxial with moulded BNC-type connectors. |
| 583 | SITE of two Bay Charging Base. Batteries are charged within the transmitters Built-in safety feature monitors cell voltage and automatically turns off the unit if problems are detected. Automatic shut-off if alkaline (non-rechargeable) batteries are installed. Automatic shut-off if damaged batteries are installed. Maintenance charging prevents battery self-discharge until the transmitter is removed from charger, to be supplied from same OEM. Charging time should be equal to or less than 80%: approx. 1:45 h, 100%: approx. 3:15 h | Charging Current 2 A and Charing Voltage 4-5V |
| 584 | SITC of Gooseneck Microphone with Quick-Mount Anti Shock Microphone Desk Stand - Cardioid Condenser Gooseneck Length: 18\\" - 20\\" Frequency Response : 30Hz - 20,000 Hz Impedance : 250 ohms Maximum Input Sound Level: 139 dB SPL, 1 kHz at 1% T.H.D. Dynamic Range: 114 dB, 1 kHz at Max SPL Signal-to-Noise Ratio: 70 dB, 1 kHz at 1 Pa LOW FREQUENCY ROLL-OFF: 80 Hz, 18 dB/octave RFI Shielding Technology Desk Stand Should Effectively isolates microphone from noise, shock and vibration transmitted through the mounting surface. |
| 585 | SITC of Hypercardioid dynamic Neodymium handheld Vocal microphone Frequency Response of 60 - 14,000 Hz Open Circuit Sensitivity -54 dB (1.9 mV) re 1V at 1 Pa or better Impedance-600 ohms or better On/off switch Integral 3-pin gold-plated XLRM-type connector Rugged all-metal construction complete with stand clamp and threaded adaptor and Foam Wind Screen |
| 586 | SITC of Wired Vocal Handheld Microphone - Element: Dynamic Pick up Pattern: Cardioid Frequency Response : 90 - 16,000 Hz Impedence : 300 ohms Open Circuit Sensitivity: –55 dB (1.7 mV) re 1V at 1 Pa Output Connector: 3 pin XLR Type Rugged metal construction for long-lasting performance & neodymium magnet for improved output and transient response Anti-shock engineering for low handling noise & Multi-stage grille design offers excellent protection against plosives and sibilance without compromising high-frequency clarity. Corrosion-resistant gold-plated XLRM-type connector Accessories Included: Adjustable stand clamp & Soft protective Pouch |
| 587 | SITC of Hypercardioid dynamic Neodymium handheld Instrument microphone Frequency Response of 60 - 14,000 Hz Open Circuit Sensitivity -54 dB (1.9 mV) re 1V at 1 Pa or better Impedance-600 ohms or better on/off switch Integral 3-pin gold-plated XLRM-type connector Rugged all-metal construction complete with stand clamp and threaded adaptor and Foam Wind Screen |
| 588 | SITC of Wired Instrument microphone - SITC of Hyper-cardioid Dynamic Instrument microphone for Percussion, Guitar, Harmonium Frequency Response of 80Hz - 17,000 Hz Open Circuit Sensitivity –56 dB (1.5 mV) re 1V at 1 Pa Impedance- 300 ohms Integral 3-pin gold-plated XLRM-type connector Rugged all-metal construction complete with stand clamp and threaded adaptor and soft pouch included |
| 589 | SITC of 8 x 8 DSP Processor 8 Analog Mic/Line input and 8 Analog Line output. Sample Rate: 48 kHz. Frequency Response: 20 Hz - 20 kHz, +/- 0.5 dB. Dynamic Range: > 110 dB. THD+Noise: < -85 dB. Interchannel Crosstalk: < -90 dB @ 1 kHz. Latency: < 1.6 ms. CMRR: > 50 dB @ 1 kHz. Mic Pre-amp Gain: +40 dB. Input Trim: +/- 24 dB. Maximum Input Level: +23 dBu. Input Impedance: 18 kΩ balanced, 9 kΩ unbalanced, Maximum Output Level: +24 dBu. Output Impedance: 200 Ω balanced, 100 Ω unbalanced. GPIO Contact Closure for External control like preset selection, I/O level control and muting. Support Wall mount Volume Level Controller on Digital Platform Support Graphical User Interface (GUI) |
| 590 | SITC of Compact 40-Input Digital mixing Console Minimum 40 inputs channel processing, 16 Aux buses Main LCR out and 6 Matrix outputs16 fully programmable mic preamps for audiophile sound quality 8 XLR outputs plus 6/6 additional line n/outputs, a phones connector and a talkback section with XLR mic input Processing : 48 kHz, 24 bit ADC and DAC converters with minimum 112 dB dynamic range AES50 ports : 2 or more, Digital AES/EBU output : 1 or more 40 bit floating point digital signal processing Internal effects engines, true stereo / mono : 8 / 16 or more Internal total recall scenes (incl. preamp and fader) : 100 or more THD + noise < 0.006% or better Frequency range 10 Hz - 22 kHz or better Equivalent input noise level -128 dBu or better Auto-ranging universal switch-mode power supply 7” or better full colour TFT display screen 48 V Phantom Power Minimum 17 motorised 100 mm faders Built-in RTA for all channel, remote controllable, auto-ranging universal switch-mode power supply |
| 591 | SITC of 16 x 8 Stage Box 6 Input, 8 Output Stage Box with 16 Microphone Preamplifiers Remote operation via shielded CAT5e cable up to 330 ft / 100 m length Switchable 48 V phantom power 2 x AES50 or OEM specific network ports or redundant connections Digital audio and control connectivity MIDI In/Out for bidirectional communication Auto-ranging universal switch-mode power supply A/D converter 24-bit, 48 kHz and D/A converter 24-bit THD + noise, unity gain, 0 dBu out< < 0.005%, unweighted Shall be from same OEM of digital mixing console |
| 592 | SITC of Active DI Boxes for electronic instruments Powered by +48 V phantom power with a 9 V battery backup Signal levels ranging from +10 to +50 dBu Frequency response from 10 Hz to 20 kHz (±3 dB) Earth Lift Switch |
| 593 | Microphone stand with Round base (medium) Supply, installation, testing & commissioning of Floor Stand for the Microphone. Stand shall be for adjustable height from 1100mm to 1800mm. Rod Combination Two/ Three piece Folding Design Stand. Material : Steel with Zinc/ Steel Die Cast Base |
| 594 | Microphone stand with Tripod base (medium) - Supply, installation, testing & commissioning of Floor Stand for the Microphone. Stand shall be for adjustable height from 890mm to 1600mm. Rod Combination Two/ Three piece Folding Design Stand. Material : Steel with Zinc/Steel Die Cast Base. |
| 595 | Music Stand - Supply, installation, testing & commissioning of Music stand. Stand shall be for adjustable height from 650mm to 1225mm. Rod Combination Three piece Folding Design Stand. Material : Steel. Foldable Music Desk of average 440mm x 225 mm. |
| 596 | Microphone stand (Desktop) - Supply, installation, testing & commissioning of Adjustable Desktop Microphone Stand. Compact stand for short-height miking and unobtrusive use on a desktop or podium with Rocker-Lug for tilting the whole shaft up to 40° for mic placement. Rocker-Lug to hold angle adjustments. Clutch to adjusts height 9\\" – 14.25\\" for comfortable positioning. |
| 597 | SITC of 11000 lumens laser projector - Resolution: WUXGA, 1DLP Laser Phosphorus projector Projection System : 1-Chip DLP Contrast ratio : Full On/Off 4,000,000:1 Color wheel : 4 Segment (RGBY) - 2X or 3X speed, Illumination type Laser phosphor Illumination performance (hrs) 20,000 Scan rates: Horizontal: 15-91kHz Vertical: 24-120Hz Pixel clock rate -594MHz Inputs: HDMI x 2, DVI-D (digital only), USB (type A), HDBaseT (RJ45), RJ45 for Control Wrap and Blend feature With Zoom lens of through distance within stage. Throw Distance between 4 mts-4.8mts projector should include with necessary mounting arrangement required as per site Fixed Projector Mount Supply, installation, testing & commissioning of custom mount for the Projector and HDMI Receiver. (The item includes providing any necessary MS fabrication supports with powder coating that may be required as per site conditions to complete the installation) |
| 598 | SITC of Projection Screen : 140\\" X 224\\" (265\\" Diagonal) Motorized projection screen with low voltage control module Supply, with unity plus gain 265\\" Diagonal (3728 mm h x 5966mm) •220V power supply •Wired remote, 16:10 aspect ratio screen. •Low Voltage Relay Option for GPIO connection/ Automation to be provided EDGE FREE® technology. •Acoustically transparent front projection screen. •4K ultra HD ready and moire-free from visual artifacts •180° viewing angle, 1.1 Gain – MaxWhite (The item includes providing any necessary MS fabrication supports with powder coating that may be required as per site conditions to complete the installation) |
| 599 | SITC of 43\\" Confidence monitor display - 43\\" 4K UHD(3840 X 2160) resolution Android LED display with built in 2.4 Ghz Wifi, 1.1 Ghz Built in Quad core processor, 2 GB DDR3 RAM, 16 GB Memory, built in Triple Core Mali 600 MHz GPU, with HDR 10, Dolby Audio, Built in Wifi and Chromecast, HDMI CEC, Built-in Bluetooth Ver.4, 20W built in speakers, HDMI 2.0 X 3, AV X 1, USB 2.0 X 1, RJ45 X 1(network connectivity only), Headphone Out x 1, SPDIF Out x 1, |
| 600 | Supply, installation, testing & commissioning of Portable trolley for confidence monitor with 45 degree tilt with protection case for monitor |
| 601 | SITC of Wooden / Metal Podium: Podiums with cable slot for HDMI, USB-C to USB-C, UAB2.0 & DATA Port. With 1 x Power Socket for external laptop / document camera. The Podium will have provision of fixing the annotator and make it up and down motion. The podium have space for CPU to get fix inside the podium along with castor wheels and brake. |
| 602 | SITC of 4K 18Gbps Multiformat HDBaseT Wallplate Extender Set - Transmission of HDMI and USB-C via HDBaseT up to 40m (4K), 70m (1080p). Supports 18Gbps for resolutions up to 4K UltraHD 60Hz (HDMI) / 30Hz (USB-C). Bidirectional PoC, pass-through for IR and RS232, EDID management. 3 USB-A v2.0 on receiver, USB-C supporting data and AV transmission. Maximum resolution: Up to 4K@60Hz (4:4:4) via HDMI, 4K@30Hz (4:4:4) via USB-C Input connectors: TX: 2x HDMI-A, 1x USB-C | RX: 1x HDBaseT (RJ45) Output connectors: TX: 1x HDBaseT (RJ45) | RX: 1x HDMI-A HDCP & EDID Management Control signals to display are transmitted via IR, RS-232 or CEC Cable Link Monitoring: Integrated HDBaseT link status monitoring |
| 603 | SITC of Wireless Presenter module Allows simultaneous present upto 4 or more screens at the same time Allows a user to manage on-screen presenters as well as queued presenters Integrated WI-FI Access Point – can be segregated from the facility LAN for security reasons Wireless screen casting through native AirPlay, Google Cast, or Miracast protocols Supports wireless video upto 1080p/30 4:2:0 Shall be controllable over IP and RS-232 both Shall have min. 1 x HDMI, 2x USB 2.0/3.0 port |
| 604 | SITC of 4x2 4K 18Gbps HDMI Matrix with Scaler and Audio De-Embedding. 4x2 HDMI Presentation Switcher with 4 HDMI inputs to 2 HDMI matrix outputs. Inputs: 4 x HDMI Input - Outputs: 2 x HDMI Outputs HDMI 2.0b for resolutions up to UltraHD / 4K 60Hz (4:4:4) incl. HDR10. HDMI 2.0b, 4K@60Hz 4:4:4 8bit, HDR 10, HDCP 2.2. SPDIF and 3.5mm output for dual HDMI OUT audio extraction and dual HDMI OUT ARC. 4K to 1080p downscaling. HDCP 2.2 compliant. Smart EDID management ARC functions on second HDMI output, analog and digital audio de-embedding. Control via web-GUI, RS232 and IR, EDID management. |
| 605 | SITC of 4K 18Gbps HDMI HDBaseT Extender Set with VLC. Transmission of HDMI via HDBaseT up to 40m (4K), 70m (1080p). Tx: Input: HDMI IN, Output: HDBT OUT, Control Ports: IR IN, IR OUT, RS232.Rx: Input: HDBT IN, Output: HDMI OUT, Control Ports: IR IN, IR OUT, RS232. Supports 18Gbps for resolutions up to 4K UltraHD 60Hz.Support resolutions up to 4K @60 4:4:4 (18Gbps). Bandwidth: 18Gbps HDMI Standard: HDMI2.0 & HDCP2.2 Bidirectional PoC, pass-through for IR, CEC and RS232, EDID management Visually lossless compression for max. 18Gbps. Robust enclosure with mounting brackets, screwable power supply. |
| 606 | SITC of Network based Control Processor AV Control and Management Network based Control Processor with required number of physical ports like RS-232, IR and Relay Supplied with 3 interface device license each for i-Pad and Android touch interface licence.2 x LAN/Ethernet Port Shall be accessible from a web browser for setup and management Supports industry-standard, secure data communications through HTTP/2, HTTPS, SSH, SFTP, and WebSockets with TLS and AES-128 encryption 3 interface device license each for i-Pad and Android touch interface licence iPhone, iPad, and Android control app support Flexible scalability for integrating one or several AV systems over a network Continuous system monitoring – quickly assess system and device status Centralized, network-based configuration and management of IP-controllable products and systems Scheduling is compatible with G Suite and Microsoft Office 365 Certification: CE, FCC |
| 607 | SITC of 9.7\\" or better Wireless Touch panel Ipad/ Android Tablet for GUI interface to control Audio Visual Devices, shall Built-in WiFi |
| 608 | SITC of Table mount with charging stand Compatible docking station for above wireless touch panel |
| 609 | SITC of 16 port PoE Network Switch, shall have QoS feature, compatible to IEEE 802.3az 10BASE-T Ethernet, IEEE 802.3i 10BASE-T Ethernet, IEEE 802.3x Flow Control, 19\\" Rack mountable complete with standard accessories |
| 610 | SITC of Wireless Access Point 802.11 a,b, g, n with POE complete with standard accessories |
| 611 | SITC of AV Credenza 24U With front glass door power distribution box Internal fans and lights, wheels |
| 612 | Supply and laying of Active USB 3.2 USB-C Cable with E-Marker – 2.00m USB 3.2 (Gen 2x1) – 10Gbps data transmission. Gold plated precision contacts USB-C male to USB-C male. High purity copper conductors and triple shielding. E-Marker, USB Power Delivery 60W, DP Alt-Mode up to 8K 30Hz. |
| 613 | Supply and laying of Certified 4K Premium High Speed HDMI Cable – 2.00m, black. HDMI version 2.0 – 18Gbps for resolutions up to 4K UltraHD 60Hz. Gold plated precision contacts . HDMI-A male to HDMI-A male. High purity, tinned OFC copper conductors and triple shielding, AWG28. |
| 614 | SITC of 24/22 AWG Microphone/Signal Cable ( as per actual) Microphone Cable Supply, installation, testing & commissioning of Microphone / audio Signal cable : Microphone cable black 6mm copper screen • 1 x 2x 0.22 sq.mm AWG 24 , • Insulation PE, Shielding Factor 99%, • Capacity Cond/Cond per 1m 68 pF, Conductor Resistance per 1 Km < 87 ohm• Oxygen Free Copper Cable |
| 615 | Microphone Cable Supply, installation, testing & commissioning of Microphone / audio Signal cable : Microphone cable black 6mm copper screen • 1 x 2x 0.50 sq.mm AWG 20, • Insulation PE, Shielding Factor 100%, • Capacity Cond/Cond per 1m 80 pF, • Conductor Resistance per 1 Km < 37 ohm, • Shielding Cu Spiral Plus metallic fleece • Oxygen Free Copper |
| 616 | Supply, installation, testing & commissioning of 2 Core 4 sqmm Speaker cable • Twinaxial 2x 4 sqmm highly flexible speaker cable with PVC outer sheath. • AWG 11, >=56 strands, resistance <4.5 ohms • Oxygen free cable. |
| 617 | Supply, installation, testing & commissioning of • 2 Core 2.5 sqmm Speaker cable Twinaxial 2x 2.5 sqmm highly flexible speaker cable with PVC outer sheath. • AWG 13, >=140 strands, resistance <7.5 ohms • Oxygen free cable. |
| 618 | Ethersound Cable with TCPIP for 100 Mtr Supply, installation, testing & commissioning of CAT6 Cable (S/UTP) or S/FTP CAT.7PUR 4 x 2 x 0.57 OFC, AWG 23 Flexible Cable • Capacity Cond/ Cond per 1 M 76pF, Surge Impedance 100ohm, • Max. Delay Skew 14 ns@100Mhz/100m, • Damping per 100m 100 Mhz 18.4 dB, 350MHz 38dB • Oxygen Free Copper Cable |
| 619 | Multi-pair Cable Supply, installation, testing & commissioning of Snake Cable 8 pair x 1 x 2x 0.14 sq.mm AWG 26, Insulation PE, Shielding Factor 100%, • Capacity Cond/Cond per 1m 65 pF, Conductor Resistance per 1 Km < 90 ohm• Oxygen Free Copper Cable |
| 620 | Installation Rack and Stage Components for Interconnectivity - Supply, installation, testing & commissioning of Interconnects, connectors (1 lot) XLR 100 Male ( HI-X3CM-BLK) and 100 Female Cable Type ( HI-X3CF-BLK) , 10 RCA ( HI-CM03), 30 Stereo ( HI-J63SPB), 30 Mono (HI-J63MPB), 10 EP ( HI-J35S02), 60 Speakon Cable Connector NL4FXX , 20 RJ45, 5 BNC, 5 PowerCon, 2 HDMI Chassis 3 USB, 5 Schuko with plates and grips. (This is in addition to all connectors mentioned in the Stage Boxes for complete connectivity in Auditorium) |
| 621 | Stage Boxes - 8 holes Supply, installation, testing & commissioning of Stage Boxes consisting of 4 mic inputs / 1 RCA input / 1 HDMI inputs / 2 Power Multi / 2 Schuko / 1 RJ 45 input / 1USB (4 x HI-X3DF-M/AC3FDZ, 1 x HDHD- FFDN, RJX8FD5T, J35SEFD) |
| 622 | Stage Boxes - 4 holes - Supply, installation, testing & commissioning of Stage Boxes consisting of 2 mic inputs/ 1 HDMI inputs/ 1 Power/ 1 RJ 45 input (2 x HI-X3DF-M/AC3FDZ, 1 x HDHD- FFDN, RJX8FD5T, J35SEFD) |
| 623 | Stage Boxes - 2 holes Supply, installation, testing & commissioning of Stage Boxes / Face Plate with 1/2 hole Speakon Connectors for Speakers |
| 624 | Standard Ethernet Cable for Control and Automation Supplying and installing enhanced cat-6 cable with 4-connector channel, performance test report as per ANSI/TIA-568.2-D suitable for networking complete as per specification. Please Enable Macros to View BoQ information |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
