Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | Taking down cement or cement lime plaster, any description on brick or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed. |
| 2 | M&L for 15 mm thick rendering on fair faces of brick work or concrete surfaces of wall in CM 1:6 and finished even and smooth (without using extra cement) complete all as specified and directed. |
| 3 | M&L for 5mm thick rendering on fair faces of brick work or concrete surfaces in CM 1:3 as in ceiling complete all as specified and directed. |
| 4 | M&L for 15 mm thick rendering on fair faces of brick work or concrete surfaces of wall in CM 1:4 using water proofing compound (WPC) and finished even and smooth (without using extra cement) complete all as specified and directed. Note: WPC measured and paid separately |
| 5 | Supply only integral waterproofing compound |
| 6 | Demolition of brick work or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc., but excluding ashlar facings, dressed stonework & precast concrete articles complete all as specified and directed. |
| 7 | M&L for Brick work with old size FLY ASH bricks, straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and directed. |
| 8 | M& for Brickwork with old size flyash bricks, straight or curved on plan to any radius inhalf brick thick walls, built in built in cement mortar 1:4 complete all as specified and directed. |
| 9 | Repairing sunken floor leakage as per following steps:-Surface preparation:-(i) Prior to application of Dr fixit powercrete, ensure to clean the substract which shoud be free from all the dust, foreign particles, loose aggregate and oil grease etc. This can be done with the help of scarifying, grinding, water jetting and sand blasting etc.(ii) The surface should be wetted well prior to application throughly with water to get SSD condition.(iii) All the depression or pin holes/pot holes to be repaired using Dr Fixit powercrete method mortar in mixing ratio of (1 kg cement : 1.50 kg silica sand : 0.50kg of Dr Fixit powercrete).Coating application:-(i) Mix Cement with Dr. Fixit Powercrete in ratio of 1 : 0.50 ( 1 kg cement OP C53 : 0.50 Dr. Fixit Powercrete ) by weight.(ii) The mix should be stirred thoroughly until smooth homogeneous paste is obtained.(iii) Apply first coat over SSD/wet condition substrate.(iv) Apply and unroll woven glass fibre cloth evenly on the wet coating before it dries out on larger areas.(v) Using a nylon brush, apply a coat of Dr. Fixit Powercrete coating over the glass fabric so as to cover the fabric, allow 5-6 hours of air drying before application of another coat of Dr. Fixit Powercrete slurry coating over the surface.(vi) Provide polymer modified protective plaster of 15-20 mm thick over the coating to ensure safety from mechanical damage. |
| 10 | Curing:-(i) Allow Dr. Fixit Powercrete coating to air cure for 3-6 hours after the final coat.(ii) Do not allow the rapid drying of the coating by covering the coating with help of polythene sheet in case of high humidity and windy condition.(iii) However, a moist curing after the air drying is advisable.(iv) Following the moist curing, Dr. Fixit Powercrete coating shall be allowed to air cured for 3 days before submerging it in water.Note - The above procedure is given for Dr Fixit Powercrete, any other equivalent make may please be used as per their manufacturer's instruction subject to approved by Engr-in-Charge. |
| 11 | M&L for 75mm thick PCC type C-2, (1:3:6) using 40mm graded stone aggregate as in plinth protection finished even and smooth without using extra cement complete all as specified and directed. |
| 12 | M&L Forming 12mm thick Expansion joints filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade ‘A’ complete all as specified and directed. |
| 13 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store & rubbish off the premises complete all as specified and directed. |
| 14 | Demolition of cement concrete (un-reinforced) in ground floor and paving not exc 15 cm thick above or below ground level and removal of entire debris as ordered outside MD land complete all as specified and directed. |
| 15 | M&L for PCC 1:2:4 (Type B1 using 20 mm graded aggregate) as in levelling course to match the undulations of roof complete all as specified and directed. |
| 16 | M&L for Vitrified tile flooring 9-10mm thick (square/rectangular) area of each tile exceeding 0.42 Sqm but not exceeding 1.00 Sqm, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles over & including 15 mm thick screed bed or bedding layer of 1:6 cement mortar for laying floor finishes complete all as specified and directed. |
| 17 | All as per item No 15 here-in-before but as in skirting/dado & including rendering 10 mm thick in cement mortar 1:4 backing coat complete all as specified and directed. |
| 18 | M&L for Non Skid Coloured Ceramic Tiles of design as approved 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles over & including 15 mm thick screed bed or bedding layer of 1:6 cement mortar for laying floor finishes complete all as specified and directed. |
| 19 | M&L for Glazed Coloured Ceramic Tiles 350 x 250 x 7 mm / 450 x 350 x 7 mm thick in vertical surface such as dado / skirting / risers to steps etc., set & jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including rendering 10 mm thick in cement mortar 1:4 complete all as specified and directed. Note- (i) The size of tiles (except thickness) may be varied during execution without any price adjustment. |
| 20 | Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc complete all as specified and directed. |
| 21 | M&L for 18-20 mm thick Machine cut Kota stone slab flooring laid over & including 20 mm thick screed bed or bedding layer of 1:6 cement mortar for laying floor finishes, laid & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & polishing complete all as specified and directed. |
| 22 | M&L for 18-20 mm thick Machine cut Kota stone slab as in riser of steps, skirting, dado & pillar over & including rendering 10 mm thick in cement mortar 1:4, laid & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & polishing complete all as specified and directed. |
| 23 | M&L for exterior floor tiles of design as approved 10 mm thick (square/rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles over & including 15 mm thick screed bed or bedding layer of 1:6 cement mortar for laying floor finishes complete all as specified and directed. |
| 24 | M&L for exterior wall tiles of design as approved 10 mm thick (square/rectangular) 350x450x8-10mm/350 x 250 x 8-10 mm / 450 x 350 x 8-10 mm thick, wall skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles over & including 10 mm thick rendering of 1:4 cement mortar for laying floor finishes complete all as specified and directed. Note- (i) The size of tiles (except thickness) may be varied during execution without any price adjustment. |
| 25 | Demolition of stone slabs and tiles of any description or thickness laid, bedded and pointed in any mortar in floors, aprons etc complete all as specified and directed. |
| 26 | M & L for Granite (Black/Ruby Red ) work (table rubbed and polished) 20 mm thick as in steps, jambs, pillars, window-cills, wash basin, cooking platforms and including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite bedded and jointed with grey cement slurry and pointed to match the shade of granite stone grinding and polishing types including screed bed 15 mm thick in CM 1:6 complete all as specified and directed. |
| 27 | M&L for Rounding to edges of stone slabs one edge, such as in steps, cooking platform & other similar situations complete all as specified and directed. |
| 28 | Taking down chowkhats or frames not exc. 1.50 sqm each with shutters (without taking off shutters from the frame) and removing to store complete all as specified and directed. |
| 29 | Taking down chowkhats or frames exc. 1.50 sqm but not exc. 4 sqm each with shutters (without taking off shutters from the frame) and removing to store complete all as specified and directed. |
| 30 | Taking down shutter of any description area not exc 1 sqm complete all as specified and directed |
| 31 | Taking down shutter of any description area exc 1 sqm but n.exc 2 sqm complete all as specified and directed |
| 32 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid door frame of size 45 x 85mm comprising of virgin PVC polymer of K value 58-60 (suspension grade), calcium carbonate and natural fibre (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC slovent cement and screwed with full body threaded star headed SS screws havng minimum frame density of 750 Kg/cum, screw withdrawal strength of 2200 N (face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticty 900 N/mm2 and resistance to spread of flame of Casss A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete all as specified and directed Note : For WPC solid door minus 5mm tolerance in dimension i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. |
| 33 | S&F Factory Made Solid PVC Moulded Door Shutters with wood free EPS 28 to 30 mm thick (stile:), with 2,4 or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm prelam PVC Sheet on back face with Particle Board Core board core, supplying & fixing in frame at site as per specification & drawing complete all as specified and directed. |
| 34 | S&F Powder Coated (minimum thickness of powder coating 50 micron) Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified and directed. |
| 35 | S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge |
| 36 | Material & Labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified and directed. |
| 37 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid door frame of size 125 x 65mm comprising of virgin PVC polymer of K value 58-60 (suspension grade), calcium carbonate and natural fibre (wood powder/rice husk/wheat husk) and non tixic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC slovent cement and screwed with full body threaded star headed SS screws havng minimum frame density of 750 Kg/cum, screw withdrawal strength of 2200 N (face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticty 900 N/mm2 and resistance to spread of flame of Casss A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete all as specified and directed (M.S hold fast/lugs or SS dash fasteners shall be paid for seperately. Note : For WPC solid door minus 5mm tolerance in dimension i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. |
| 38 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 35 mm thick comprising of virgin polymer of K value 58-60 (suspension grade), calcium carbonate and natural fibre (wood powder/rice husk/wheat husk) and non tixic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 Kg/cum and screw withdrawal strength of 1800 N (face) & 900 N (Edge), minimum compressive strength of 50 N/mm2, modules of elasticty 850 N/mm2 and resistance to spread of flame of Casss A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessay full body threaded star headed counter sunk S.S screws complete all as specified and directed. Note :Stainless steel butt hinges and necessary S.S screws shall be paid separately. |
| 39 | S & F Factory made single extruded WPC (Wood Polymer Composite) solid plain skeleton door shutter of 35 mm thick comprising of virgin polymer of K value 58-60 (suspension grade), calcium carbonate and natural fibre (wood powder/rice husk/wheat husk) and non tixic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 Kg/cum and screw withdrawal strength of 1800 N (face) & 900 N (Edge), minimum compressive strength of 50 N/mm2, modules of elasticty 850 N/mm2 and resistance to spread of flame of Casss A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessay full body threaded star headed counter sunk S.S screws including and tainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanized wire staples beads complete all as specified and directed. Note : Stainless steel butt hinges and necessary S.S screws shall be paid separately. |
| 40 | S&F Factory made prepowdercoated steel window and vents (Box Section) with glass shutter and fly proof shutter incl guard bars as per HQ CEJZ Drg No CEJZ/TD/980 of sh 1/2 & 2/2 with and including all precoated fittings, precoated towerbolts on all shutters, 4 mm thick glass pan and stainless steel wiremesh, complete all as specified and directed. |
| 41 | M&L for Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed. |
| 42 | S&F 18/19 mm thick 'Prelaminated particle board, interior grade,prelaminated both side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and directed. |
| 43 | S&F Sheet glass 5.5 mm thick ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified and directed. |
| 44 | M&L for PCC type B1 (1:2:4) using 20 mm graded aggregate including necessary formwork as in lintels upto 1.5 m clear span, cills, steps; seismic & other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded for chamfered angles and throating complete all as specified and directed. |
| 45 | M&L for forming jambs, etc., to openings, including cutting, toothing and properly bonding into old work, also facing, jointing and pointing to match existing work, complete new work built in CM(1:4) or cement lime mortar (1:2:9) complete all as specified and directed. |
| 46 | S&F Butt hinges medium weight cold rolled Aluminium anodised 100mm long complete all as specified and directed. |
| 47 | S&F 100mm long stainless steel butt hinges fixed with SS screws complete all as specified and directed. |
| 48 | S&F Aluminium anodised barrel tower bolts of extruded section 150mm long complete all as specified and directed. |
| 49 | S&F Aluminium handles cast type anodised of 150mm complete all as specified and directed. |
| 50 | S&F 300mm Brass, sliding door bolt with sand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled or drawn brass bolts and fixed complete all as specified and directed. |
| 51 | S & F in repair helical Door spring ordinary rat tail rod pattern springs including roller and roller plate complete of mild steel 300 mm long complete all as specified and directed. |
| 52 | S&F in repair Mortice lock, vertical type size 100 mm 4 lever complete all as specified and directed |
| 53 | S&F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised, 40 mm Width of flaps (when open) complete all as specified and directed. |
| 54 | S&F Aluminium Hat pegs, solid body, 125mm to 175 mm complete all as specified and directed. |
| 55 | S&F 150 mm Hasp and staple, aluminium anodised, wire type, stove enamelled black, including bolt to hinge plate and fixed with screw complete all as specified and directed. |
| 56 | S&F magnetic catcher with nut and screw of mild steel bright finish complete all as specified and directed. |
| 57 | S&F 40 mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finished complete all as specified and directed. |
| 58 | M&L for ATT Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified and directed. |
| 59 | M&L for ATT treatment to the soil under plinth protection at the rate of 5 litres of emulsion per sqm of surface complete all as specified and directed. |
| 60 | S&F in repair 25 mm dia stainless steel curtain rod brass chromium plated including fancy type brackets fixing with fancy type bracket, stop rollers etc complete all as specified and directed. |
| 61 | Supply & Fixing 'in repair' 18 mm thick, PVC sheet one side prelaminated of approved texture as in Kitchen cabinet and cupboard (with shelves and partitions) including necessary fitting & fixture as per manuacturer's instructions complete all as specified & directed. |
| 62 | S&F in repair, 18/19 mm thick, high density PVC/WPC solid fibre board with prelaminated PVC sheet as Kitchen and bed room cupboard shutter and frame and inside shelves and side walls complete all as specified and directed. |
| 63 | M&L for preparation of new or previously untreated steel surfaces of any description, over 10 cm in width or girth, not otherwise described & applying two coat of synthetic enamel paint (ordinary tint) over & including one coat of red oxide, zinc chrome primer complete all as specified and directed. |
| 64 | M&L for preparation of newly plastered or unplastered brick work or concrete surfaces & applying two coats of oil bound distemper over a coat of primer over a coat of 1-2mm thick wall care putty complete all as specified and directed. |
| 65 | M&L for preparation of old decorated surfaces of walls by complete removal of existing treatment and applying two coat of oil bound distemper over a coat of primer over a coat of 1-2mm thick wall care putty complete all as specified and directed. |
| 66 | M&L for preparation of new decorative surfaces of wall including, cornices (plastered or unplastered) of any description, rubbing, scrapping by hand held sander / long handle sander and Jet pressure washing and applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50gm/litre and UV resisitance as per IS 15489:2004, alkali & fungal resistance dirt resistance exterior paint (Apex -Ultima Protek) of required shade (company depot tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces including filing undulations with white cement based putty mixed with multi purpose mixer complete all as directed. |
| 67 | M&L for complete removal of existing treatment of walls including, cornices (plastered or unplastered) of any description, rubbing, scrapping by hand held sander / long handle sander and Jet pressure washing and applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50gm/litre and UV resisitance as per IS 15489:2004, alkali & fungal resistance dirt resistance exterior paint (Apex -Ultima Protek) of required shade (company depot tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over old surfaces including filing undulations with white cement based putty mixed with multi purpose mixer complete all as directed. |
| 68 | M&L for preparation of old painted Steel surfaces of any description, over 10 cm in width or girth, not otherwise described and applying one coat of Synthetic enamel paint (ordinary tint) complete all as specified and directed. |
| 69 | M&L for preparation of old painted Wooden surfaces of any description, not otherwise described, over 10 cm width or girth and applying one coat of Synthetic enamel paint (ordinary tint) complete all as specified and directed. |
| 70 | M&L for preparation of newly plastered surfaces of ceiling and applying three coat of white wash complete all as specified and directed. |
| 71 | M&L for preparation of old surfaces of any description and applying two coat of white wash on old decorated surfaces of walls including filling cracks and holes etc complete all as speciifed and directed. |
| 72 | Taking down steel tubing and connections including cleaning for refixing or removal from site for 15mm bore pipe all as specified and directed by Engr-in-charge. |
| 73 | All as per srl item No 71 here-in-before but 20mm bore pipe |
| 74 | Supplying and laying 20 mm outer dia of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified. |
| 75 | S&F 15mm bore GI tubes medium grade with all fitting and fixed complete to walls or ceilings or laid in floors complete all as specified and directed. |
| 76 | All as per srl item No 74 here-in-before but 20mm bore |
| 77 | M&L for Welded steel wire fabric supplied and fixed complete to wood or steel members weight not exc 4 kg/sqm complete all as specified and directed. |
| 78 | Refixing old steel tubing and connections in new or old position (walls, ceiling, floors, etc) of 20 mm bore of pipe complete all as specified and directed. |
| 79 | S&F Rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) 1000 litre capacity, (minimum triple layer) hoisted and fixed in position all as specified in SSR Part-I, including dismantling of old u/s water storage tank and removing to store complete all as specified and directed. |
| 80 | S&F ball valves for 20 mm bore dia of pipe high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe & fixed. (Minimum weight 210 gms) complete all as specified and directed. |
| 81 | S&F in repair, Brass chromium plated Wall Mixer 3-in-1 System with provision for both Hand Shower & Overhead Shower complete with 115 mm long bend pipe, connecting legs & wall flanges (without Hand & Over Head Shower) for 15 mm bore of pipe complete all as specified and directed. |
| 82 | S&F in repair, Brass chromium plated Wash Basin Mixer with raised 'J' shaped swinging spout (Table Mounted Model) with 450 mm long braided hoses for 15 mm bore of pipe complete all as specified and directed. |
| 83 | S&F in repair, Chromium plated Angular Stop Cock with wall flange for 15 mm bore of pipe complete all as specified and directed. |
| 84 | S&F in repair, Chromium plated Two-way Bib Cock for 15 mm bore of pipe complete all as specified and directed. |
| 85 | S&F in repair, 15 mm dia of bore, fancy type, chromium plated stop valves, cast copper alloy, with long shank and cup (concealed type), screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed. |
| 86 | S&F in repair, 15 mm dia of bore, fancy type, chromium plated stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed. |
| 87 | S&F in repair, 32 mm bore, brass chromium plated bottle traps for Wash basins with inlet & outlet screwed for pipe or connections including necessary packing, union & cap & fixed complete all as specified and directed. |
| 88 | S&F in repair, 32 mm bore, PVC waste pipe for Wash Basin/Kitchen Sink etc complete all as specified and directed. |
| 89 | S&F in repair, 32 mm dia of bore, Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed. |
| 90 | S&F in repair, Chromium Plated Grating, 100 mm dia with waste hole fixed on floor trap, nahani trap etc complete all as specified and directed. |
| 91 | S&F in repair, Health Faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube & ABS wall hook including making connections & fixed in position complete in all respect as specified. |
| 92 | S&F in repair, Vitreous china table top wash hand basin, white, size 640x425x155 mm excluding taps, waste, chain & plug & porcelain stopper but including supply & fixing of 32 mm dia of bore, brass chromium plated waste coupling complete all as specified and directed. |
| 93 | S&F in repair, Brass Chromium Plated, tubular towel rail, 20 mm dia, D type, 60 cm long between flanges etc complete all as specified and directed. |
| 94 | S&F in repair, Soap Dish Holder any type fixed to plug with chromoium plated brass screw complete all as specified and directed. |
| 95 | S&F in repair, Corner Glass Shelf with brackets complete all as specified and directed. |
| 96 | S&F in repair, Stainless Steel Double Coat Hook complete all as specified and directed. |
| 97 | S&F in repair, Sheet Glass Shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and directed. |
| 98 | S&F in repair, Toilet paper holder with flat recessed type stainless steel complete all as specified & directed. |
| 99 | S&F in repair, Door Seal with aluminium beading and 50 mm wide rubber seal, fixed to Aluminium/Wooden doors complete all as specified and directed. |
| 100 | S&F in repair, Floor door stopper of aluminium alloy body and tongue, anodised, over all length of cover plate 140 mm, with hard drawn steel spring, fixed in door complete all as specified and directed. |
| 101 | S&F in repair, 600 mm x 450 mm bevelled edge looking mirror of selected quality glass, mounted on 6 mm thick AC building board or commercial plywood & fixed to wooden plugs with chromium plated brass screws & cup washers complete all as specified and directed. |
| 102 | S&F in repair, Swivel Looking Mirror, rectangular shape of size 0.63 m x 0.445 m of selected quality glass mounted on wall with chromium plated brass screws complete all as specified and directed. |
| 103 | S&F in repair, Single Door PVC Cabinet Mirror of size 350 mm x 450 mm with internal shelves complete all as specified and directed. |
| 104 | S&F in repair, Stainless Steel Towel Ring Round complete all as specified and directed. |
| 105 | S&F in repair, Stainless Steel Towel Rack 600 mm long with lower hangers complete all as specified and directed. |
| 106 | S&F in repair, Europian WC, Single Piece, Vitreous China with UF Soft Close Slim Seat Cover, Hinges, Dual Flush Cistern Fitting, Fixing all Accessories, Size: 360 mm x 655 mm x 765 mm, P Trap-180 mm complete all as specified and directed. |
| 107 | S&F in repair, 125 mm size, Brass chromium plated shower rose with or without swivel joints, including fixing to steel pipe or union complete all as specified and directed. |
| 108 | S&F in repairs PVC connection 15mm size with PTMT nuts of length 600mm complete all as specified and directed. |
| 109 | Taking down of eves gutter,rain water pipes of any size or pattern including all fittings etc complete all as specified and directed. |
| 110 | S&F 110 mm bore, PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed. |
| 111 | S&F 110 mm bore, PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls complete all as specified and directed. |
| 112 | S&F 75 mm bore, PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed. |
| 113 | S&F 75 mm bore, PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls complete all as specified and directed. |
| 114 | S&F in repair 100mm dia Stack clampsout of 50 mm by 5 mm flat iron and 16 mm dia around iron stays including bolts and nuts and securing ends of stays to wall or roof making good all respect completed as directed as specified |
| 115 | S&F PVC (SWR) bends ISI marked any radius of 110 mm bore with access door complete all as specified and directed. |
| 116 | S&F PVC (SWR) bends ISI marked any radius of 75 mm bore with access door complete all as specified and directed. |
| 117 | S&F PVC (SWR) junction single, (single T) equal or un equal of 110 mm bore of pipe complete all as specified and directed |
| 118 | S&F PVC (SWR) junction single, (single T) equal or un equal of 75 mm bore of pipe complete all as specified and directed |
| 119 | S&F PVC (SWR) branch pices (single Y) equal of 110 mm bore of pipe complete all as specified and directed |
| 120 | S&F PVC (SWR) branch pices (single Y) equal or un equal of 75 mm bore of pipe complete all as specified and directed |
| 121 | S&F PVC (SWR) floor trap 75 mm, setting and jointing with solvent cement complete all as specified and directed |
| 122 | S&F in repair PVC (SWR) multi trap 75 mm, setting and jointing with solvent cement complete all as specified and directed |
| 123 | S&F in repair PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed |
| 124 | S&F in repair 125mm/ 150mm dia mild steel chromium plated grating fixed on floor trap / nahani trap in Cement mortar 1:6 , all as specified and directed by Engr-in-charge. |
| 125 | S&F in repair Gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe & fixed in 20 mm bore dia of pipe complete all as specified and directed. |
| 126 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed. |
| 127 | Taking down carefully copper/aluminium point wiring ( light,fan,power point or bell point etc) complete including fixture and fitting such as switches,ceiling rose holders & regulators light fittings etc. Removing materials to store for keeping in safe custody or for taking credit (credit a for above items should be made as per condition seperately) and making good distrubed surfaces of walls, floors etc complete all as specified and directed at site. |
| 128 | Taking down old/unservicablelight fitting any type, tube light fitting & fixtures, etc and making good to the dirsturbed surfaces of walls/floor etc to match with existing surfaces including white washing/colour to match with existing wall/floor/ceiling finishes etc complete all as specified and directed. |
| 129 | Taking down old/unservicable distribution boards by disconnection of electric connection carefully SPN DBs/TPN DBs/main Switch including old unserviceable MCCBs/MCBs, Isolators, etc and making good to disturbed surface etc complete all as specified and directed. |
| 130 | Taking down carefully copper/aluminium Sub Main wiring/service connection of any size from surface/connected/existing conduit of any height and removing materials at site and making good disturbed surfaces of walls, floors roofs etc complete all as specified and directed. |
| 131 | M&L for point wiring using approved colour coding as per IS, with multistranded copper conductor 1.5 Sqmm (nominal area), two single core, PVC insulated and unsheathed FRLS cable 1100 volts grade ISI-694 marked drawn through in and including heavy duty PVC concealed conduit of white/ivory colour including all accessories after chasing in wall/ceilling etc, heavy duty ISI marked with GI sunken boxes 1.2mm thick, 60mm deep with earth dolly, covered with modular white cover plate with inner frame suitable for modular swithes, including PVC insulated multistranded copper conductor 1.5 Sqmm (nominal area) single core FRLS cable as earth continuity conductor to common earth and connecting to earth dolly including cutting, chasses and making good disturbed surface to match with existing finish with plaster complete all as specified and directed for the following :- |
| 132 | One light point controlled by one, one way switch 5 Amps. |
| 133 | One fan point/exhaust fan point controlled by one, one way switch 5 Amps and regulator. |
| 134 | One 3 pin 5 Amps switch socket outlet point controlled by one, one way switch on the same board. |
| 135 | One 3 pin 5 Amps switch socket outlet point controlled by one, one way switch on indelpendednt board. |
| 136 | All as per item Srl No 130 here-in-before but using 2.5 Sqmm single core copper conductor cable of multistranded FRLS, PVC insulated unsheathed 1100 volts grade for 5/15 amps witch socket combination point including necessary running of 2.5 Sqmm copper conductor FRLS, PVC wire as earth continuity conductor alongwith wiring an connecting to the common earth dully, complete all as specified and directed. |
| 137 | All as per item Srl No 130 here-in-before but using 4 Sqmm single core copper conductor cable of multistranded FRLS, PVC insulated unsheathed 1100 volts grade for metal clad box point including necessary running of 4 Sqmm copper conductor FRLS, PVC witre as earth continuity conductor alongwith wiring an connecting to the common earth dully, complete all as specified and directed. |
| 138 | S&F Lamp holder, PVC/polycarbonate type with back plate suitable for battan fittings, complete all as specified and directed. |
| 139 | S&F Modular switch 1 way 6A, 1 module complete all as specified and directed. |
| 140 | S&F Modular switch 1 way 16A, 1 module complete all as specified and directed. |
| 141 | S&F Socket, 6A - 2/3 pin combined 2 module complete complete all as specified and directed. |
| 142 | S&F Socket 6A/16A - 2/3 pin combined 2 module complete complete all as specified and directed. |
| 143 | Supply and fixing MCCB 4 Pole, 415 V, Adjustable type, 100 Amps with breaking capacity 16 KA complete all as specified and directed. |
| 144 | S&F ceiling rose surface type PVC/Polycarbonate isolated body, 65x 20mm, 3 terminals, complete all as specified & directed. |
| 145 | S&F 9 W LED bulb, 5 star rating B-22 type complete all as specified & directed. |
| 146 | Supply and fixing LED lights fitting 1x 20 W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose compete all as specified and directed. |
| 147 | Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed. |
| 148 | Supply & fixing in repair LED light down lighter by recess or surface mounted 12 watt, warm white, circular/Square, 1200 lumen with fixing arrangemnts on ceiling complete all as specified & directed. |
| 149 | S & F for LED luminaire 600 mm x 600 mm square LED panel 35/36 watts, 220V recessed/surface type with high efficieny PMMA diffuser soft glare free light complete with drovers, holders, LED lamp suitable for roof ceilling, including connecting up with driver three core flexible copperr conductor cases of suitable size complete all as specefied and directed. |
| 150 | Supply and fixing LED security light fitting 35 watt 230 V AC outdoor type with high pressure die ast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection including bracket made of 32 mm dia GI tubing medium grade of suitable size including fixing clamps & light fitting etc complete all as specified and directed. |
| 151 | M&L sub main wiring (concealed type) in & including PVC Rigid Conduit of suitable size with two single core FRLS PVC insulated unsheathed cable, 1100 volts, grade having stranded copper conductor of 06 sqmm nominal cross sectional area each drawn into and including PVC conduit and all accessories including one single core 6.00 sqmm copper conductor for earth continuity conductor connected to earth dolly complete all as specified and as directed. Note : Two run single core cable(1 x 6 Sqmm single core cable of Red/Yellow/Blue colour for Phase + 1 x 6 Sqmm single core cable Black colour for Nutral), 1 x 6 Sqmm single core cable Green colour for earth conductor and one run of PVC conduit shall be measured as a unit length. |
| 152 | S & F for sheet metal enclosure MCB DB VTPN 4 Way vertical type with incoming as MCCB with 200 Amps rated bus bar 415 volts double door with magnetic locking system including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and directed. (Note:- MCCB will be measured and paid separately ) |
| 153 | S & F for sheet metal enclosure MCB DB SPN 8 Way with 200 Amps rated bus bar 240 volts double door with magnetic locking system including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and directed. |
| 154 | S&F single pole and neutral enclosure with a two pin and earth plug and socket complete with and including one double pole MCB 20 A, 10 KA 240 volt complete all as specified and as directed. |
| 155 | S & F MCCB of capacity 160 Amps, 4 pole,415 Volts, breaking capcity 36 KA complete all as specified and directed. |
| 156 | S & F MCB single Pole and neutral rated capacity 32 Amps, 240 Volts, breaking capcity 10 KA \\"C\\" curve complete all as specified and directed. |
| 157 | S & F MCB single Pole rated capacity 5 to 32 Amps, 240 Volts, breaking capcity 10 KA \\"C\\" curve complete all as specified and directed. |
| 158 | Supply and fixing ceiling fans complete with blades, down rods, electronic moduler regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE Five star rated with all necessary connection as specified and as directed. |
| 159 | M&L for taking down exhaust fan of any sweep, any type and after repairing, painting refix on old location complete all as specified and directed. |
| 160 | M&L sub main wiring (concealed type) in & including PVC Rigid Conduit of suitable size with two single core FRLS PVC insulated unsheathed cable, 1100 volts, grade having stranded copper conductor of 2.5 sqmm nominal cross sectional area each drawn into and all accessories including one single core 2.50 sqmm copper conductor for earth continuity conductor connected to earth dolly complete all as specified and as directed. Note : Two run single core cable(1 x 2.5 Sqmm single core cable of Red/Yellow/Blue colour for Phase + 1 x 2.5 Sqmm single core cable Black colour for Nutral), 1 x 2.5 Sqmm single core cable Green colour for earth conductor and one run of PVC conduit shall be measured as a unit length. |
| 161 | Excavation in trenches for laying of cables ,poles and stay in any type of soil not exceeding 1.5 mtr wide and not exceeding 1.50 mtr deep and getting out complete all as specified ad dirtected. |
| 162 | Returning & filling in, including spreading and leveling, watering and well ramming in layers n.exc. 25 cm complete all as specified ad dirtected. |
| 163 | Removing excavated materials not exc 50 mtr and depositing where complete all as specified ad dirtected. |
| 164 | M&L for unwashed Sand cushioning to under ground cable provided with a layer of 8 cm deep before laying and 15 cm covering above the top edge of cable after laying complete all as specified.Note : Measurement shall be done after puning down of sand. |
| 165 | Supply and laying un-reinforced precast concrete cable covers, Class LV, Type I, flat, size 250 mm x 150mm x 40mm, complete all as specified and as directed. |
| 166 | S & F 40 mm dia GI Pipe light grade for cable protection passing under road/floor or for fixing to poles all as complete all as specified and directed. |
| 167 | Supply, Laying & testing and commissioning LT underground cable 1100 volts grade, 50 Sqmm 3.5 Core LT XLPE insulated and PVC sheathed heavy duty armoured with multi staranded aluminium conductor laid in pipes, trenches/ducts, on poles etc of size complete all as specified and directed. |
| 168 | M&L earthing complete with galvanised steel earth plate electrode 600mmx600mmx6mm thick buried directly in ground (earh pit not less than 2.25m deep below normal ground level) with top edge of earth plate not less than 1.5 m below normal ground level connected to galvanised earth wire 4.00 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron, all as shown in electrical plate No 5, connected to earthing test point including excavation/earth work in any type of soil, PCC 1:3:6 type C-2 in pit and CI pit pit cover including funnel covered with wire mess and handle duly reinforced with 6 mm round bars both ways @ 125 mm c/c, GI protection pipe 15mm bore light grade and watering pipe 20mm bore medium grade complete all as specified and directed. |
| 169 | Schedule of credit amount of Rs 1,40,541.20 to be deducted during AOC. Please Enable Macros to View BoQ information |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
