Tender For Extension Of The Second Floor With Lgsf Framing System, Including Electrical Works For The Powergrid Centre Of Excellence (Coe) At The Institute Computer Centre, Iit Roorkee, Roorkee-Uttarakhand

TDR : 55753782

Tender Notice
BOQ

21 Days Left

Roorkee , Uttarakhand

Tender Brief : Tender For Extension Of The Second Floor With Lgsf Framing System, Including Electrical Works For The Powergrid Centre Of Excellence (Coe) At The Institute Computer Centre, Iit Roorkee

Document Fees
₹ 1180 /-

EMD
₹ 950000.0 /-

Tender Value
Refer document

Submission Date
22-06-2026

Competition Type
Indian

Bidding Type
Tender

Need a Business Loan? Apply Now !


1	EARTH WORK
2	Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge
3	All kinds of soil
4	Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating Each deposited layer by ramming and watering, lead up to 50 and for all lift.
5	Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.
6	Surface dressing of the ground including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m.
7	All kinds of soil
8	CONCRETE WORK
9	Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:
10	1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)
11	1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources
12	Providing and laying damp-proof course 50 mm thick with cement concrete 1:2:4 (1 cement: 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size erived from natural sources).
13	Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer's specification.
14	Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7 kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.
15	REINFORCED CEMENT CONCRETE
16	Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement -All work up to plinth level :
17	1 :1.5:3 (1 cement : 1.5 coarse sand (zone-Ill} derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)
18	Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement.
19	1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal sizederived from natural sources)
20	Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement: 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregae 20 mm nominal size derived from natural sources).
21	Centering and shuttering including strutting, propping etc. and removal of form for :
22	Foundations, footings, bases of columns, etc. for mass concrete.
23	Suspended floors, roofs, landings, balconies and access platform
24	Lintels, beams, plinth beams, girders, bressumers and cantilevers
25	Columns, Pillars, Piers, Abutments, Posts and Struts
26	Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.
27	Thermo-Mechanically Treated bars of grade Fe-500D or more.
28	Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.
29	Thermo-Mechanically Treated bars of grade Fe-500D or more.
30	Smooth finishing of the exposed surface of R.C.C. work with 6 mm thick cement mortar 1:3 (1 Cement : 3 fine sand).
31	Extra for rendering smooth the top of suspended floors, landings and staircases (treads and risers) with cement mortar 1:2 (1 cement : 2 coarse sand), including a floating coat of neat cement and protecting the surface with a layer of 7.5 cm of earth laid over 15 mm of fine sand in case of suspended floor and bricks laid in mud mortar in case of landings and steps, including subsequent removal and cleaning of the same
32	Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections.
33	MASONRY WORK
34	Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :
35	Cement mortar 1:4 (1 cement : 4 coarse sand)
36	Cement mortar 1:6 (1 cement : 6 coarse sand)
37	Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.
38	Cement mortar 1:3 (1 cement :3 coarse sand)
39	Cement mortar 1:4 (1 cement :4 coarse sand)
40	Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry
41	Providing and laying Autoclaved Aerated concrete(AAC) blocks masonry 100 mm/ 125 mm thick with Grade-1 AAC blocks of density 551 to 650 kg/cum conforming to IS:2185 (Part 3) in super structure above plinth level up to floor V level in cement mortar 1 :4 (1 cement: 4 coarse sand ). The rate includes providing and placing in position 2 Nos 6 mm dia M.S. bars at every third course of masonry work.
42	Brick edging 7cm wide 11.4 cm deep to plinth protection with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 including grouting with cement mortar 1 :4 (1 cement : 4 fine sand)
43	CLADDING WORK
44	Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels.
45	Granite stone slab of colour black, Cherry/Ruby red
46	Area of slab over 0.50 sqm
47	Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.
48	Granite work
49	Extra for fixing marble /granite stone, over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive, including cleaning etc. complete.
50	Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.
51	WOOD AND PVC WORK
52	Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately).
53	Second class teak wood
54	Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick
55	Float glass panes
56	5.0 mm thick glass panes (weight not less than 12.50 kg/sqm).
57	Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.
58	35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws.
59	Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:
60	35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws
61	30 mm thick including ISi marked Stainless Steel butt hinges with necessary screws
62	25 mm thick (for cupboard) including ISi marked nickel plated bright finished M.S. Piano hinges with necessary screws
63	Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured).
64	Extra for providing vision panel not exceeding 0.1 sqm in all type of flush doors (cost of glass excluded) (overall area of door shutter to be measured):
65	Rectangular or square
66	Extra for cutting rebate in flush door shutters (Total area of the shutter to be measured).
67	Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete
68	2nd class teak wood
69	50x12 mm
70	Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete
71	Fixed to steel windows by welding
72	Providing and fixing ISi marked oxidised M.S. sliding door bolts with nuts and screws etc. complete (Copper oxidised as per IS 1378)
73	250x16 mm
74	Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc. complete :
75	125x64x1.90 mm
76	100X58X1.90 mm
77	Providing and fixing IS : 12817 marked stainless steel butt hinges (heavy weight) with stainless steel screws etc. complete :
78	100x60x2.50 mm
79	Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete
80	Providing and fixing aluminium sliding door bolts, ISi marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete :
81	300x16 mm
82	Providing and fixing aluminium tower bolts, ISi marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :
83	150x10 mm
84	Providing and fixing aluminium hanging floor door stopper, ISi marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete
85	Twin rubber stopper
86	Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with zinc coating of 120 gms/sqm(both side inclusive), consisting of floor and ceiling channel 50 mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beadsat corners (25 mm x 25 mm x 0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture's specification and direction of engineer in charge all complete.
87	75 mm overall thickness partition with 12.5 mm thick doubleskin fire rated Glass Reinforced Gypsum (GRG) plasterboard conforming to IS: 2095: part 3 (Board with BIScertification marks)
88	Providing and fixing bright finished 100 mm mortice lock with 6 levers without pair of handles of approved quality for aluminium door, with necessary screws etc complete as per direction of Engineer-in-charge.
89	Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality
90	1.5 mm thick
91	Providing and fixing wire gauge shutters using stainless steel grade 304 wire gauge with wire of dia 0.5 mm and average width of aperture 1.4 mm in both directions for doors, windows and clerestory windows with necessary screws:
92	35 mm thick shutters.
93	With ISI marked stainless steel butt hinges of required size. - Second class teak wood.
94	Providing and fixing fire resistant door frame of section 143 x 57 mm having built in rebate made out of 16 SWG G.I. sheet (zinc coating not less than 120 gm/sqm) duly filled with vermuculite based concrete mix, suitable for mounting 60 minutes fire rated door shutters. The frame is fitted with intumuscent fire seal strip of size 10x4 mm (minimum) alround the frame and fixing with dash fastener of approved size and make, including applying a coat of approved brand fire resistant primer etc. complete as per direction of Engineer-in-charge (Dash fastener to be paid for separately).
95	Providing and fixing 50 mm thick glazed fire resistant door shutters of 60 minutes fire rating conforming to IS:3614 (Part-II), tested and certified as per laboratory approved by Engineer-in-charge, with suitable mounting on door frame, consisting of vertical styles, lock rail, top rail 100 mm wide, bottom rail 200 mm wide, made out of 16 SWG G.I.sheet (zinc coating not less than 120 gm/m2) duly filled FR insulation material and fixing with necessary stainless steel ball bearing hinges of approved make, including applying a coat of approved fire resistant primer etc. all complete as per direction of Engineer-in-charge (panneling to be paid for separately).
96	Providing and fixing glazing in fire resistant door shutters, fixed panels & partitions etc., with G.I. beading made out of 1.6 mm thick G.I. sheet (zinc coating not less than 120 gm/m²) of size 20 x 33 mm screwed with M4 x 38 mm SS screws at distance 75 mm from the edges and 150 mm c/c , including applying a coat of approved fire resistant primer/ powder coating of not less than 30 micron on G.I. beading, & special ceramic tape of 5 x 20 mm size etc complete in all respect as per NBC 2016, IS 16231 (Part 3):2016 and as per direction of Engineer-in-charge with glass of required thickness having 60 minutes of fire resistance both integrity & radiation control (EW60) and minimum 20 minutes of insulation (EI20). The manufacturer have to give test report/certification of fire glass and the glass should have the stamp showing the value of E, EW & EI. The glass shall be tested in approved NABL accredited lab or by any other accreditation body which operates in accordance with ISO/IEC 17011 and accredits labs as per ISO/IEC 17025 for testing and calibration scopes shall be eligible. The maximum glazing size shall not be more than 1100x2200 mm (w x h) or 2.42 sqm.
97	Providing and fixing panic bar / latch (Double point) fitted with a single body, Trim Latch & Lock on back side of the Panic Latch of reputed brand and manufacture to be approved by the Engineer- in- charge, all complete.
98	Providing and fixing factory made uPVC glazed/wire mesh windows/ doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1. 70 mm for Series R 1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and lnline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge. Wire mesh / Glazing of plain/ toughened/ laminated/ double glass unit with / without high performance coatings as per design requirements and conforming to IS: 3548 & IS: 16231 shall be paid separately. Note:- Structural design proof checked from a Government Engineering Institute, to be provided by the manufacturer for (i) Sites with basic wind speed > 45 m/sec as per IS 875 - Part 3 (ii) Sites with structure height more than 20m for all wind speeds
99	Three track three panels sliding window with two glazed & one wire mesh panels with Aluminium channel for roller track, wool pile, nylon rollers with SS 304 body.
100	Using R2 series with frame (70mm & above) x (40mm & above) & both glazed and fly screen sash (25mm & above) x (50mm & above) with zinc alloy (zamak) powder coated touch locks with hook. (Height upto 1.2 metre).
101	Using R3 series with frame (98 mm & above) x (40 mm & above) & both glazed and fly screen sash (30 mm & above) x (55 mm & above) with zinc alloy (zamak) powder coated handle on every glazed panel along with multi-point locking system. (Height upto 1.8m).
102	Fixed window/ ventilator without mullion/ transom.
103	Using R2 series with frame (39 mm & above) x (39 mm & above). (Height upto 1.2 metre)
104	Using R3 series with frame (55 mm & above) x (45 mm & above). (Height upto 2.5 metre)
105	Fixed window/ ventilator with mullion / transom
106	Using R1 series with frame (33mm & above) x (35 mm & above) & both glazed and fly screen sash (33 mm & above) x (50mm & above) (Height upto 0.90 metre).
107	Using R2 series with frame (39 mm & above ) x (39 mm & above) & mullion (39 mm & above) x (60 mm & above). (Height upto 1.2 metre)
108	Using R3 series with frame (55 mm & above ) x (45 mm & above) & mullion (55 mm & above) x (65 mm & above). (Height upto 2.5 metre
109	Ventilator Casement window single panel with or without fixed panel with S.S. 304 friction hinges as per size and weight of sash, single point locking zinc alloy (zamak) powder coated handles
110	Using R2 series with frame (39 mm & above) x (39 mm & above) & sash /mullion (39 mm & above) x (60 mm & above). (Height upto 1.2 metre)
111	Providing and fixing stainless steel (SS-304 grade) friction hinges to the side/top hung uPVC windows, of approved quality, with necessary stainless steel screws etc. as per direction of Engineer-in-charge.
112	300 x 19 x 1.9 mm
113	350 x 19 x 1.9 mm
114	Providing and fixing casement handle made of zinc alloyed (white powder coated) for uPVC casement window with necessary screws etc. complete.
115	Providing and fixing zinc alloyed (white powder coated) touch lock for uPVC sliding window with necessary screws etc. complete.
116	Providing and fixing steel roller for uPVC sliding window with necessary screws etc. complete.
117	Providing and fixing steel roller for uPVC sliding door with necessary screws etc. complete.
118	Providing and fixing steel (white power coated) crescent lock for uPVC sliding window/ door with necessary screws etc. complete.
119	Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete.
120	125mm
121	100mm
122	STEEL WORK
123	Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete:
124	Providing and fixing M.S. Tubular frames for doors, windows, ventilators and cupboard with rectangular/ L-Type sections, made of 1.60 mm thick M.S. Sheet, joints mitred, welded and grinded finish, with profiles of required size, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer.
125	Fixing with 15x3 mm lugs 10 cm. long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size).
126	Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.
127	Hot finished welded type tubes
128	Providing and fixing carbon steel galvanised ( minimum coating 5 micron) dash fastener of 10 mm dia double threaded 6.8 grade (yield strength 480 N/mm2), counter sunk head, comprising of 10 mm dia polyamide PA 6 grade sleeve, including drilling of hole in frame , concrete/ masonry, etc. as per direction of Engineer-in-charge.
129	10 x 140 mm
130	10 x 160 mm
131	Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).
132	Providing & fixing fly proof wire gauze to windows, clerestory windows & doors with M.S. Flat 15x3 mm and nuts & bolts complete.
133	Stainless steel (grade 304) wire gauze of 0.5 mm dia wire and 1.4 mm aperture on both sides.
134	Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows all complete with :
135	4.0 mm thick glass panes.
136	5.5 mm thick glass panes.
137	Providing and fixing angle iron frames for doors, windows and ventilators of mild steel Angle sections of size 35x35x5 mm, joints mitred and welded by angle iron 35x35x5 mm or 35x 5 mm flat pieces to the existing T-iron frame or to the wall with dash fastener, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer, all complete as per the direction of Engineer-In-charge.
138	FLOORING WORK
139	Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 gradedstone aggregate) finished with a floating coat of neat cement, ncluding cement slurry, but excluding the cost of nosing of steps etc. complete
140	40 mm thick with 20 mm nominal size stone aggregate
141	Cement plaster skirting up to 30 cm height, with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement
142	18 mm thick
143	Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :
144	25 mm thick.
145	Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.
146	Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.
147	Double charge vitrified tile polished finish of size
148	Size of Tile 600 x 600 mm
149	Deduct for not using 20 mm thick cement mortar 1 :4 (1 cement : 4 coarse sand) bedding in laying of floor tiles and jointing with grey cement slurry @ 3.3 kg/ sqm
150	Fixing glazed/ Ceramic/ Vitrified floor tiles with cement based high polymer modified quick-set tile adhesive (Water based) conforming to IS: 15477, in average 3 mm thickness.
151	Providing and laying Vitrified tiles in different sizes {thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1 :3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete.
152	Size of Tile 600x600 mm
153	Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge.
154	Size of Tile 600x600 mm
155	Providing and laying Vitrified tiles in floor with different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately).
156	Size of Tile 600x600 mm
157	Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1 :4 (1 cement: 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-inCharge :
158	Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent
159	ROOFING WORK
160	Providing flat iron brackets 50x3 mm size with necessary bolts, nuts and washers etc. for fixing G.S. sheets gutters with purlins.
161	Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design
162	In 75x75 mm deep chase
163	Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.
164	Providing and fixing plain multipurpose cement board (Hight pressure steam cured) with suitable screws for cement particle board in ceiling etc. complete (frame work to be paid seperatately).
165	6 mm thick Cement fiber board, Type-B, Category-III as perIS: 14862: 2000
166	Providing fixing thermal insulation of ceiling (under deck insulation) with Resin Bonded Fibre glass wool conforming to IS : 8183, density 24kg / m3, 50mm thick, wrapped in 200 G Virgin Polythene bags, fixed to ceiling with metallic cleats (50x50x3 mm) @ 60 cm and wire mesh of 12.5 mm x 24 gauge wire mesh, for top most ceiling of building.
167	Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.
168	75 mm diameter
169	110 mm diameter
170	Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion
171	Coupler
172	110 mm
173	Single pushfit Coupler
174	110mm
175	Single tee with door
176	110x110x110 mm
177	Single tee without door
178	110x110x110 mm
179	Bend 87.5°
180	110 mm bend
181	Shoe (Plain)
182	110 mm shoe
183	Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete
184	110 mm
185	Providing and fixing false ceiling at all heights including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x1 0x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws@ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :
186	12.5 mm thick tapered edge gypsum plain board conformingto IS: 2095- (Part I) :2011 (Board with BIS certification marks)
187	Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-Charge) of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05mm) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.
188	Providing and fixing precoated galvanised steel sheet roofing accessories of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05 mm) with Zinc coating 120 gram per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete :
189	Ridges plain (500 - 600mm)
190	Flashings/ Aprons.( Upto 600 mm)
191	Gutter (600 mm over all girth)
192	Providing and fixing GI Clip in Metal Ceiling System of 600x600 mm module which includes providing and fixing 'C' wall angle of size 20x30x20 mm made of 0.5 mm thick pre painted steel along the perimeter of the room with help of nylon sleeves and wooden screws at 300 mm center to centre, suspending the main C carrier of size 10x38x10 mm made of G.I steel 0.7 mm thick from the soffit with the help of soffit cleat 37x27x25x1 .6 mm, rawl plugs of size 38x12 mm and C carrier suspension clip and main carrier bracket at 1000 mm c/c. Inverted triangle shaped Spring Tee having height of 24 mm and width of 34 mm made of GI steel 0.45 mmthick is then fixed to the main C carrier and in direction perpendicular to it at 600 mm centers with the help of suspension brackets. Wherever the main C carrier and spring T have to join, C carrier and spring T connectors have to be used. All sections to be galvanized@ 120 gms/sqm (both sideinclusive), fixing with clip in tiles into spring T with :
193	GI Metal Ceiling Clip in plain Beveled edge global white color tiles of size 600x600 and 0.5 mm thick with 25 mm height, made of G I sheet having galvanizing of 100 gms/ sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending.
194	Providing and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI (solar refractive index) > 78, solar reflection > 0.70 and initial emittance> 0.75 on waterproof and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1 :4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1 :1, including rubbing and polishing of the surface upto 3 cuts complete, including providing skirting upto 150 mm height along the parapet walls in the same manner.
195	Providing and fixing thermal insulation with Resin Bonded rock wool conforming to IS: 8183, having density 48 kg/m3,50 mm thick,wrapped in 200 G Virgin Polythene Bags fixed to wall with screw, rawel plug & washers and held and in position by criss cossing GI wire etc. complete as per directions of Engineerin- Charge.
196	FINISHING WORK
197	12 mm cement plaster of mix :
198	1:4 (1 cement: 4 coarse sand)
199	1:6 (1 cement: 6 coarse sand)
200	15 mm cement plaster on rough side of single or half brick wall of mix
201	1:4 (1 cement: 4 coarse sand)
202	1:6 (1 cement: 6 coarse sand)
203	12 mm cement plaster finished with a floating coat of neat cement of mix :
204	1:3 (1 cement: 3 fine sand)
205	1:4 (1 cement: 4 fine sand)
206	Extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers
207	Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.
208	Finishing walls with textured exterior paint of required shade :
209	New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @2.20kg/10 sqm.
210	Finishing walls with Acrylic Smooth exterior paint of required shade :
211	New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm).
212	Finishing walls with Premium Acrylic Smooth exterior paintwith Silicone additives of required shade
213	New work (Two or more coats applied @ 1.43 ltr/ 10 sqm. Over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm).
214	Applying priming coat: With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel work (second coat)
215	Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade
216	Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacturer.
217	Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.
218	Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour
219	Two coats
220	Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content.
221	With water thinnable cement primer on wall surface havingVOC content less than 50 grams/litre
222	REPAIRS TO BUILDING
223	Dismantling W.C. Pan of all sizes including disposal of dismantled materials including malba all complete as per directions of Engineer-in-Charge
224	Hacking of CC flooring including cleaning for surface etc. complete as per direction of the Engineer-in-Charge
225	Providing and laying APP (Atactic Polypropylene Polymer) modified prefabricated five layer, 3 mm thick water proofing membrane, black finished reinforced with glass fibre matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 litre/sqm by the same membrane manufactured of density at 25°C, 0.87 - 0.89 kg/litre and viscocity 70 - 160 cps. Over the primer coat the layer of membrane shall be laid using butane torch and sealing all joints etc., and preparing the surface complete. The vital physical and chemical parameters of the membrane shall be as under : Joint strength in longitudinal and transverse direction at 23°C as 350/300 N/5 cm. Tear strength in longitudinal and transverse direction as 60/80N. Softening point of membrane not less than 150°C. Cold flexibility shall be upto -2°C when tested in accordance with ASTM, D - 5147. The laying of membrane shall be got done through the authorised applicator of the manufacturer of membrane :
226	3 mm thick
227	DISMANTLING AND DEMOLISHING
228	Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge.
229	Nominal concrete 1:3:6 or richer mix (i/c equivalent designmix)
230	Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge
231	Extra for scrapping, cleaning and straightening reinforcement from R.C.C. or R.B. work.
232	Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.
233	In cement mortar
234	Removing mortar from bricks and cleaning bricks including stacking within a lead of 50 m (stacks of cleaned bricks shall be measured):
235	From brick work in cement mortar
236	Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead :
237	Of area 3 sq. metres and below
238	Of area beyond 3 sq. metres
239	Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead
240	Of area 3 sq. metres and below
241	Of area beyond 3 sq. metres
242	Dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates, bolts, nuts, cutting rivets, welding etc. including dismembering and stacking within 50 metres lead
243	Dismantling steel work manually/ by mechanical means in built up sections without dismembering and stacking within 50 metres lead as per direction of Engineer-in-charge
244	Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.
245	For thickness of tiles 10 mm to 25 mm
246	Demolishing brick tile covering in terracing including stacking of serviceable material and disposal of unserviceable material within 50 metres lead.
247	Demolishing mud phaska in terracing and disposal of material within 50 metres lead.
248	Dismantling C.I. or asbestos rain water pipe with fittings and clamps including stacking the material within 50 metres lead :
249	75 to 80 mm dia pipe
250	100 mm dia pipe
251	Dismantling G.I. pipes (external work) including excavation and refilling trenches after taking out the pipes, manually/ by mechanical means including stacking of pipes within 50 metres lead as per direction of Engineer-in-charge :
252	15 mm to 40 mm nominal bore
253	Above 40 mm nominal bore
254	Dismantling of flushing cistern of all types (C.I./PVC/Vitrious China) including stacking of useful materials near the site and disposal of unserviceable materials within 50 metres lead.
255	Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.
256	Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable material and stacking of serviceable material with in 50 meters lead as directed by Engineerin-charge.
257	Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved
258	SANITARY INSTALLATIONS
259	Providing and fixing P.V.C. waste pipe for sink or wash basinincluding P.V.C. waste fittings complete.
260	Semi rigid pipe
261	40 mm dia
262	Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard boardground fixed to wooden cleats with C.P. brass screws and washers complete.
263	Providing and fixing toilet paper holder :
264	C.P. brass
265	Providing and fixing floor mounted, white vitreous chinasingle piece,double traps syphonic water closet of approved brand/make, shape,size and pattern including integrated white vitreous china cistern of capacity 10 litres with dual flushing system, including all fittings andfixtures with seat cover, cistern fittings, nuts, bolts and gasket etcincluding making connection with the existing P/S trap, complete inall respect as per directions of Engineer-in-Charge.
266	WATER SUPPLY WORK
267	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls
268	20 mm nominal dia Pipes
269	Providing and fixing uplasticised PVC connection pipe withbrass unions :
270	45 cm length
271	15 mm nominal bore
272	20 mm nominal bore
273	ALUMINIUM WORK
274	Providing and fixing aluminium work for doors, windows, ventilators andpartitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanicallywherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :
275	For fixed portion
276	Powder coated aluminium (minimum thickness of powder coating 50 micron)
277	For shutters of doors, windows & ventilators includingproviding and fixing hinges/ pivots and making provisionfor fixing of fittings wherever required including the cost ofEPDM rubber / neoprene gasket required (Fittings shall bepaid for separately)
278	Powder coated aluminium (minimum) thickness of powder coating 50 micron)
279	Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge
280	Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side
281	Pre-laminated particle board with decorative lamination on both sides
282	Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):
283	With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm)
284	Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineerin- charge.
285	With stainless steel cover plate minimum 1.25 mm thickness
286	With brass cover plate minimum 1.25 mm thickness
287	Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete.
288	Upto 5mm depth and 5 mm width
289	Providing and fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P brass/ stainless steel screws @ 200mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge. (Only weight of grill to be measured for payment).
290	Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately).
291	WATER PROOFING WORK
292	Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.
293	CONSERVATION OF HERITAGE BUILDING
294	Providing and fixing double scaffolding system (cup lock type) on the exterior side of building/structure, upto 25 metre height, above ground level, including additional rows of scaffolding in stepped manner as per requirement of site, made with 40mm dia M.S. tube, placed 1.5 metre centre to centre, horizontal & vertical tubes joint with cup & lock system with M.S. Tubes, M.S. tube challis, M.S. clamps and staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for execution of work of cleaning and/ or pointing and/ or applying chemical and removing it thereafter. The scaffolding system shall be stiffened with bracings, runners, connecting with the building etc, wherever required, if feasible, for inspection of work at required locations with essential safety features for the workmen etc., complete as per directions and approval of Engineer-in-charge.Note:- (1) The elevational area of the scaffolding shall be measured for payment purpose. (2) The payment will be made once only for execution of all items for such works.
295	NEW TECHNOLOGIES AND MATERIALS
296	Providing, mixing and applying bonding coat of approved adhesive on chipped portion of RCC as per specifications and direction of Engineer-In-charge complete in all respect.
297	SBR Polymer (@10% of cement weight) modified cementitious bond coat @ 2.2 kg cement per sqm of surface area mixed with specified proportion of approved polymer
298	Providing and fixing false ceiling at all heights with integral densified calcium silicate reinforced with fibre and natural filler false ceiling tiles of Size 595x595 mm of approved texture, design and patterns as per CPWD Specification 2019, to be laid in true horizontal level suspended on interlocking metal T-Grid of hot dipped galvanised iron section of 0.33 mm thick (galvanized @ 120 grams per sqm including both sides)comprising of main-T runners of size 24x38 mm of length 3000 mm,cross - T of size 24x32 mm of length 1200 mm and secondaryintermediate cross-T of size 24x32 mm of length 600 mm to formgrid module of size 600 x 600 mm, suspended from ceiling using galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 12x50 mm long dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 76x25x25x1.6 mm fixed with grid and Z cleat of size 25x37x25x1.6 mm thick with precut hole on both 25 mm flange to pierce into 12x50 mm or even bigger size dash fastener if require, fixed with Glavanised iron perimeter wall angle or size 24x24x0.40 mm of length 3000 mm to be fixed on periphey wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40 mm long dry wall S.S screws. The work shal be carried out as per specifications, drawing and as per directionsof the Engineer-in-Charge.
299	With 15 mm thick Tegular edged light weight calcium sliciate false ceiling tiles
300	Designing, providing, installing and fixing factory finished custom designed cold form Light Gauge Steel Framed super structure comprising of steel wall panel, trusses, purlins etc manufactured out of minimum 0.75 mm thick steel sheet as per design requirements. The steel sheet shall be galvanized (AZ-150gms Aluminium Zinc Alloy coated steel having minimum yield strength 300-550 Mpa) conforming to AISI specifications and IBC 2009 for cold formed steel framing and construction and also as per IS: 875-1987, ISO 800-1984 and IS:8011975. The wind load shall be as per provisions of IS 875 (part -III). LGSFS frame shall be designed as per IS: 801 using commercially available software such as Frame CAD Pro-11.7/ STAAD PRO-V8i/ ArchitekV2.5.16/ Revit architecture-2011 or equivalent. Proper usage of Connection Accessories like Heavy Duty Tension Ties, Light Duty Hold-ons, Twist Straps (to connect truss with wall frames), Strong Tie, Tie Rod, H-Brackets, Boxing Sections, L-Shaped Angles for better structural stability. The framing section shall be cold form C-type having minimum web depth 89 mm x 39mm flange x 11mm lip in required length as per structural design requirement duly punched with dimple/ slot at required locations as per approved drawings. The slots will be along centre line of webs and shall be spaced minimum 250mm away from both ends of the member. The frame can be supplied in panelized or knock down condition in specific dimensions and fastened with screws extending through the steel beyond by minimum of three exposed threads.
301	All self drilling tapping screws for joining the members shall have a Type II coating in accordance with ASTM B633(13) or equivalent corrosion protection of gauge 10 & 12, TPI 16 & 8 of length 20mm. The frames shall be fixed to RCC slab or Tie beam over Neoprene rubber using self expanding carbon steel anchor bolt of dia as per approved drawings. design subject to minimum 12mm diameter and 121mm length conforming to AISI 304 and 316 at 500mm c/c with minimum embedment of 100mm in RCC (RCC to be paid separately) and located not more than 300mm from corners or termination of bottom tracks complete in all respects. The item also includes the submission of stability reports duly examined and issued by any NIT/IIT. The rate includes the concept design, detailed design, fabrication of sections, transportation, installation and all required fixing arrangement at site as described above.
302	Providing and fixing of external wall system on Light gauge steel frame work with outer face cement boards as per standard sizes fixed with self- drilling / taping screws / fasteners @ 60cm c/c of approved make. A groove of 2 mm to 3mm shall be maintained and grooves shall be sealed with silicon based sealant. The board shall be fixed in a staggered pattern. Screws shall be of counter sunk rib head of 1.60mm to 4 mm thick or 8 to 10 gauge of length varying from 25 to 45 mm and. Internal face 12.5 mm thick gypsum plaster board fixed on cement board as per standard sizes fixed with selfdrilling / taping screws / fasteners @ 60cm c/c of approved make, proper taping and jointing to be done using fiber mesh tape and epoxy and acrylic based jointing compound for seamless finish.(cost of frame work to be paid for separately)
303	Outer face- Outer face having 6 mm thick fiber cement board Type A, Category-IV as per IS:14862:2000 fixed on 9 mm thick fiber cement board, Type A, Category-IV as per IS:14862:2000 (high pressure steam cured) Inner Face- 12.5 mm thick gypsum plaster board conforming to IS 2095:2011 fixed on 8 mm thick fibre cement board of Type B, Category-III as per IS:14862:2000 (High pressure steam cured)
304	Providing and fixing internal wall panels on Light gauge steel frame work with 12.5mm thick gypsum plaster board conforming IS 2095:2011 fixed on cement board as per standard sizes fixed with self-drilling / taping screws / fasteners @ 60cm c/c of approved make, Screws shall be of counter sunk rib head of 1.60mm to 4 mm thick or 8 to 10 gauge of length varying from 25 to 45 mm. Proper taping and jointing to be done using fiber mesh tape and epoxy and acrylic based jointing compound for seamless finish.(cost of frame work to be paid for separately
305	Cement Fiber Board 8 mm thick of Type B, Category III as per IS 14862:2000 (High pressure Steam Cured)
306	Providing and fixing in all exterior face panels breathable vapour barrier underneath the cement fiber board as per National Building Code 2009 complete as per direction of Engineer-in-charge
307	Supplying and installation of moisture resistant/fire resistant cement board as per standard sizes fixed with self-drilling / taping screws. Screws shall be of counter sunk rib head of 1.60mm to 4 mm thick or 8 to 10 gauge of length varying from 25 to 45 mm.
308	Cement Fiber Board 6 mm thick as per IS 14862:2000 of type B (High pressure Steam Cured)
309	Providing & Applying weather proof sealant on outer joints of approved make conforming to IS & directed by Engineer-in-charge
310	Sealant 25mm x 10mm at joints
311	Providing and fixing Scaffolding net of required width made of high density Polyethylene UV stabilized knitted on warp knitting machines having density 100grams/sqm and shading coefficient minimum 75% around the construction site/ for vertical extension as per requirement including fastening/tying with building/ scaffolding pipes or with any other fixtures etc. complete as per direction of Engineer-in-Charge. (One time payment shall be made for providing Scaffolding net from start of work till completion of work including shifting if any. The Scaffolding net shall be the property of the contractor on completion of the work)
312	Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/Clerestory windows & other Frames/ Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall bepaid for separately). Note: For WPC solid door/window frames, minus 5 mm tolerance in dimensions i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made
313	Frame size 45 x 70 mm
314	Frame size 45 x 85 mm
315	Frame size 50 x 100 mm
316	Frame size 50 x 125 mm
317	Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately)
318	30 mm thick
319	35 mm thick
320	MISCELLANEOUS WORKS
321	Providing and fixing under counter wash basin with fitting accessories size 485x370x205 mm shape rectangular Jaquar make model no. CNS-WHT-701 or equivalent approved make as per direction of EIC
322	Providing & fixing counter mounted basin tap Jaquar make or equivalent (auto closing) complete as per direction of Engineer in charge.
323	Providing and fixing Bowl with Cistern for Extended wall hung WC with PP soft close seat cover, Hinges, Dual Flush cistern fitting. Accessories set, size 380x630x770 mm jaquar make model no. CNS-WHT-353SPPZ or equivalent approved make as per directions of EIC
324	Providing and fixing wall hung partition division HINDWARE make model no. SU810SC-C-STD-CR or equivalent of approved make as per direction of EIC.
325	Providing and fixing urinal valve auto closing system with built in control cock & wall flange jaquar make Model no PRS- 077 or equivalent of approved make as per directions of the engineer in charge.
326	Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm or 340x410x265 mm sizes respectively.
327	Providing and fixing health faucet with 8mm dia. 1 meter long flexible tube & wall hook. Jaquar make model no. ALD-573 or equivalent approved make as per the direction of EIC
328	Providing and fixing bottle trap of Jaquar make 32 mm size with 250mm x190mm long wall connectionn pipe & wall flange model no. ALD-PHR 769L 250x190 or equivalent approved make as per the direction of Engineer-in-charge
329	Providing and fixing 100 mm dia CP floor jali (Heavy Duty) as per direction of EIC
330	Providing and fixing CP brass basin inlet connection angle valve ESSCO make model no. SQT-526 NKM or equivalent approved make etc. complete as per direction of EIC
331	Providing and fixing Towel ringround with round flange of Jaquar make (Model no.CAN-1121BN) or equivalent approved make approved make fixed with CP brass screws etc. complete as per directions of the Engineer in charge.
332	Providing and fixing regular body of concealed stop cock suitable for 15mm pipe line with plastic protectionn cap of Jaquar make ALD-083FT or equivalent approved make along with compatible exposed part kit of concealed stop cock with fitting sleeve, operating lever & adjustable wall flange of Jaquar make CON-083FTK or equivalent approved make etc. complete as per direction of EIC.
333	Providing and fixing CP Brass pillar cock with auto closing system Jaquar make model no. PRS-031 or equivalent approved make as per direction of EIC.
334	Providing and fixing CP brass angular stop cock with valve flange Jaquar Make Model No. CON-059KN or equivalent approved make as per directions of EIC
335	Providing and fixing CP brass bib cock jaquar make CON-047KN with wall flange or equivalent of approved make as per directions of Engineer In-charge
336	Providing and fixing 75 mm dia UPVC nahani trap with material and labour etc. complete as per directions of EIC.
337	Providing and fixing 32 mm thick ISI mark flush door shutters non-decorative type of centuryply make or equivalent approved make complete in all respects as per directions of EIC
338	Supplying and fixing SS pull handle H type (pair) size of 450 mm Dorset make model no. SH 18 P SS or equivalent of approved make as per direction of EIC
339	Providing & fixing of rolling blinds NEHA/VISTA/CLASSIC or any oyher equivalent approved brand with prior approval of EIC , complete in all respect
340	Grinding of Existing Stone Floor/DADO/Skirting including polishing complete in all respect.
341	Providing and fixing 12 mm thick toughened glass in fixed portion including godrej glass clip fittings or equivalent as per approved make necessary holes etc. for fixing required fittings, all complete as per direction of EIC
342	Providing and fixing hydraulic door closer Godrej make or equivalent approved make with necessary accessories and screws etc. complete in all respects as per directions of EIC
343	Extra difference cost for providing and fixing glass door fitting combo set with lock patch. Top bottom patch fittings of dorset model no. CS 100 WL or equivalent approved make having brand logo embossed on the body/plate with a double spring mechanism and door weight upto 100 kg for doors, including cost of cutting floor, embedding in floors as required and making good the same matching to the existing floor finishing and cover plate with brass pivot and single piece MS sheet (With SS Cover plate minimum 1.25 mm thickness) outer box with slide plate etc. complete as per the direction of EIC.
344	Providing and fixing mortice handle lock with of doorset make model no. Cetto
345	Providing, mixing and applying 12 mm thick ready mix cement mortar of approved make as per specifications and directions of Engineer-in-charge.
346	Providing, mixing and applying 15 mm thick ready mix cement mortar of approved make as per specifications and directions of Engineer-in-charge.
347	Providing and fixing 5mm thick toughened glass etc. complete as per direction of engineer in charge
348	Providing and laying Heavy Duty tiles in floor with different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately).Size of Tile 600x600 mm
349	Providing and fixing Door mounted hanging type Door stopper of dorset make model no. Ds ht (z) or equivalent approved make with ss screws etc. complete
350	Providing and fixing 250x16 mm size Stainless steel Aldrop of Dorset make model no. ALDSM(250x16) or equivalent approved make with nuts ans SS screws etc. complete
351	Providing and fixing 10 inch length and 10mm dia square shape stainless steel tower bolts of Dorset make model no. TS-1010-10\\"or equlvalent approved make with ss screws etc. complete
352	Providing and fixing 12 inch length and 10mm dia square shape stainless steel tower bolts of Dorset make model no. TS-1210-12\\"or equlvalent approved make with ss screws etc. complete
353	Providing and fixing beveled edge mirror of superior glass (of approved quality and required size) complete with 6 mm thick cement bonded particle board ground fixed to spacers with C.P. brass/SS screws and washers etc all complete as per directios of the Engineer In charge.
354	Providing and fixing 1.00 mm thick deck sheeting (including shear connectors/ stud of 19mm dia. & 110mm height) for RCC slabs as per specifications including fixing the same. The contractor shall take all precautions to prevent any bending in sheeting. (RCC & R/F shall be paid seperately). Plan area shall be measured for payment. The vendor must be able to supply 2hr fire rating for deck sheet with concrete. The deck sheet must have minimum zinc coating of 275 g/m2 (Plan Area shall be measured for Payment)
355	Providing and fixing high strength friction bolts (M8.8/ 10.9) of following grades for connetions, as per structural drawing and as instructed by Project Managers. Rate to include cost of grouting, MS washer fastening screws/ bolts, tightening with nuts and check nuts, providing necessary holes in shearwalls (if required) etc.
356	Providing and fixing stainless steel fastener of required dia as per requirement or as per direction of EIC. 140 mm long
357	Providing and fixing prefabricated sandwiched Polyurethane Foam Panel (PUF panel) on Roof having overall thickness of minimum 80 mm and base thickness without corrugation of minimum 50 mm, having density of PU foam 40± 2 kg/cum, the top covering on the roof panel of Tapezoideal Precoated Galvanized iron sheet of total coated thickness 0.5mm (pitch of corrugation as approved by Engineer-in-charge) and bottom covering of micro ribbed precoated galvanized iron sheet of total coated thickness 0.5mm, for both sheets base metal of minimum 0.45 mm thickness with total coating thickness of 0.05mm with zinc coating 120 grams per sqm as per IS: 277, in 240 MPa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The PUF panel shall be fixed using self drilling / self tapping screws of required size with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surface, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.
358	For Calculation purpose only
359	Sub Total (A)
360	Supplying and Wiring for light point/fan point/exhaust fan point/call bell point with 1.5 mm² FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit ISI 16 gauge with modular type switch, modular plate,suitable GI box and earthing the point with 1.5 mm² FRLS PVC insulated copper conductor single core cable etc as required.
361	Supplying and fixing suitable size G.I. box with modular plate and cover in front on surface or in recess, including providing and fixing 5 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection, painting etc. as required.
362	Supplying and fixing suitable size G.I. box with modular plate and cover in front on surface or in recess including providing and fixing 6 pin 15/16 & 5/6 amps modular socket outlet and 15/16 amps modular type switch, connection, painting etc. as required..
363	Supplying and Wiring for circuit/ submain line with 2x1.5 mm² FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit ISI 16 gauge along with 1 no 1.5 mm² FRLS PVC insulated copper conductor single core cable for loop earthing as required.
364	.....do..... but 2x2.5 mm² + 1x2.5 mm² earth wire
365	.....do..... but 2x4 mm² + 1x4 mm² earth wire
366	.....do.....but 2x6 mm² + 1x6 mm² earth wire
367	.....do..... but 2x10 mm² + 1x6 mm² earth wire
368	.....do..... but 2x16 mm² + 1x6 mm² earth wire
369	.....do..... but 4 X 4 mm² + 2 X 4 mm² earth wire
370	.....do..... but 4 X 6 mm² + 2 X 6 mm² earth wire
371	.....do..... but 4 X 10 mm² + 2 X 6 mm² earth wire
372	.....do..... but 4 X 16 mm² + 2 X 6 mm² earth wire
373	Supplying and drawing 2 x 1.5 sq mm sizes of FRLS PVC insulated copper conductor, single core cable in the exisiting surface/ recessed steel/PVC conduit as required with connection complete.
374	.....do..... but 3 X 1.5 sq mm
375	.....do..... but 3 X 2.5 sq mm
376	.....do..... but 3 X 4 sq mm
377	.....do..... but 2 X 6 sq mm
378	.....do..... but 3 X 6 sq mm
379	.....do..... but 2 X 10 sq mm
380	.....do..... but 2 X 16 sq mm
381	.....do..... but 2 X 25 sq mm
382	.....do..... but 1 X 35 sq mm
383	.....do..... but 1 X 50 sq mm
384	Supplying and fixing of 20 mm sizes of steel conduit ISI 16 gauge along with accessories in surface/ recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required.
385	.....do..... but 25 mm size
386	.....do..... but 32 mm size
387	.....do..... but 40 mm size
388	S/F of G.I. Flexible pipe 32 MM size including suitable size of PVC saddle and others all accessories as required.
389	S/F of steel wire rainforced flexible uPVC pipe 20 MM size including suitable size of PVC saddle and others all accessories as required. Makes : AKG/ BEC/ Prescision
390	.....do..... but 25 MM size
391	.....do..... but 30-32 MM size
392	S/F of PVC Batten/casing caping of 20X12 MM size including suitable size of PVC cover and others all accessories as required.
393	.....do..... but 25X12 MM size
394	.....do..... but 32X12 MM size
395	.....do..... but 50X16 MM size
396	.....do..... but 50X50 MM size
397	.....do..... but 75X50 MM size
398	.....do..... but 100X50 MM size
399	Supplying and fixing 3 pin, 5 amp ceiling rose on the existing junction box/ wooden block including connection etc as required.
400	Supplying and fixing 5/6 amps modular type switch on existing modular type plate & switch box including connections but excluding modular plate etc. as required.
401	.....do..... but 15/16 amp switch
402	.....do..... but 5 pin 5/6 amp socket outlet
403	.....do..... but 6 pin 15/16 amp socket outlet
404	.....do..... but Bell push
405	.....do..... but stepped type electronic fan regulator (two module)
406	.....do..... but modular blanking plate.
407	Supplying and fixing PVC batten/ angle holder including connections etc. as required.
408	Supplying and fixing 1 or 2 module Modular base & cover plate on existing modular metal boxes etc. as required.
409	.....do.....but 3 module
410	.....do.....but 4 module
411	.....do.....but 6 module
412	.....do.....but 8 module
413	.....do.....but 12/18 module
414	S/F of 2.8 to 3 mm thick phenolic laminated bakelite sheet including cutting as required with brass machine screw and cup washer complete.
415	S/F of 1.5 - 2.00 mm thick Stainless steel sheet including cutting as required with machine screw and cup washer complete.
416	Providing and fixing 125 amp, 16 KA, rating and breaking capacity TP MCCB in existing cubicle panel board including drilling holes in cubicle panel, making connections etc. as required.
417	...do- but 150 / 160 amp 35 KA
418	.....do..... but 250 amp 35 KA MCCB
419	.....do..... but 400 amp 35 KA MCCB
420	.....do..... but 630 amp 50 KA MCCB
421	Providing and fixing 125 amp, 36 KA, rating and breaking capacity 4P MCCB in existing cubicle panel board including drilling holes in cubicle panel, making connections etc. as required.
422	.....do..... but 250 amp 36 KA MCCB
423	.....do..... but 400 amp 50 KA MCCB
424	.....do..... but 630 amp 50 KA MCCB
425	Supplying and fixing of 8-way, double door prewired SP&N MCB distribution board of steel sheet for 240 volts on surface/ recess complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)
426	.....do..... but 12-way, double door
427	Supplying and fixing 4 way (4+12), double door, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)
428	do... but 6 way (6 + 18), double door TPN DB
429	do... but 8 way (4 + 24), double door TPN DB
430	Supplying, installation, testing and commissioning of surface/ recess mounting, vertical type, 415 volts, prewired, TPN MCB distribution board of sheet steel, dust protected, duly phosphatized and powder painted, inclusive of 200 amps tinned copper busbar, common neutral link, earth bar, din bar for mounting MCB's , detachable gland / knock out plate and superior make terminal connectors for all incommining and outgoing circuits, duly prewired with adequate size of FRLS PVC insulated copper conductor upto the terminal connector/ neutral link and ready for installation of 4 ways (4+12) double door (but with out MCB's and incommer MCCB) as required.
431	..do.. but 8 way (4 + 24), double door VTPN DB
432	Supplying and fixing Cable End Box (Loose Wire Box) suitable fortriple pole and neutral, sheet steel, Vertical MCB distribution board, 415 Volts, on surface/ recess, complete with testing and commissioning etc. as required.
433	Supplying and fixing of 16 amps to 32 amps rating, 240 volts, 10 kA, “C” curve, Single Pole Modular circuit breaker suitable for inductive load in the existing Modular Box complete with connections, testing and commissioning etc as required.
434	Supplying and fixing 5 amps to 32 amps rating single pole, 240/415 volts, \\"C\\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.
435	.....do..... but 40 to 63 amp SP MCB
436	.....do..... but 5 to 32 amp DP MCB
437	.....do..... but 40 to 63 amp DP MCB
438	.....do..... but 5 to 32 amp TP MCB
439	.....do..... but 40 to 63 amp TP MCB
440	.....do..... but 5 to 32 amp 4P MCB
441	.....do..... but 40 to 63 amp 4P MCB
442	Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.
443	Supplying and fixing 25 amps rating, double pole, (single phase and neutral), 240 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.
444	.....do.....but 40 amps DP RCCB
445	.....do.....but 63 amps DP RCCB
446	Supplying and fixing 40 amps rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.
447	.....do.....but 63 amps 4P RCCB
448	Supplying and fixing 2P / 4P MCB sheet steel enclosure on surface/ recess for 415 volts complete with suitable bus bar for neutral including connections, testing and commissioning etc. as required.
449	Supplying and fixing TP/4P MCCB sheet steel enclosure on surface/ recess for 415 volts MCCB upto 250Amps complete with suitable bus bar for neutral including connections, testing and commissioning etc. as required.
450	Supplying and fixing 30 A, 415 V, TPN Industrial typesocket outlet, with 4 pole and earth, metalenclosedplug top along with 30 A \\"C\\" curve, TPMCB, in sheetsteel enclosure, on surfaceor inrecess, with chainedmetal cover for the socket out let and complete withconnections, testing and commissioning etc. asrequired.
451	Supplying and fixing of 63A , 415V TPN Industrial type socket outlet (three phase+ Neutral + Earth), with 4 pole and earth, metal enclosed plug top along with 63 A \\"C\\" curve 4PMCB, in sheet steel enclosere on surface or in recess with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.
452	Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure/ HDPE FRP Chamber with cover plate having locking arrangement and watering pipe of 2.7 Meter long etc. with charcoal/ coke and salt as required.
453	Supplying and laying 25 mm X 5 mm G.I strip at 0.50 Meter bellow ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)
454	Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure/ HDPE FRP Chamber with cover plate having locking arrangement and watering pipe of 2.7 Meter long etc. with charcoal/ coke and salt as required.
455	Supplying and laying 25 mm X 5 mm copper strip on surface/recess as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm in cluding soldering as required)
456	Providing and fixing 25 mm x 5 mm copper strip at 0.50 meter below the ground as strip earth electrode, including connection/termination with brass nut, bolt, spring washer etc.as required.(Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm) on surface or in recess for connection including soldering etc. as required.
457	Providing and fixing G.I. tape 20 mm x 3 mm thick on parapet or surface of wall for lightning conductor complete including soldering, clamping, CC as required
458	Supplying and making end termination with brass compression gland and aluminium lugs for 4 core 10 mm² (25mm) size of PVC insulated and PVC sheathed/ XLPE aluminium conductor cable of 1.1 kV grade as required.
459	..do...but for 3 ½ or 4 core 70 mm² PVC/XLPE cable
460	..do...but for 3 ½ or 4 core 95 mm² PVC/XLPE cable
461	..do...but for 3 ½ or 4 core 300 mm² PVC/XLPE cable
462	Making earth point with boring 18 Mt. deep with 80 mm dia G.I. pipe “B” class ISI. The top pipe 6 mt. length will be duly holed across the pipe at a distance of 15 cm apart in 4 rows. The each joint should be welded/ Brazing, 30 cm x 30 cm CI / HDPE FRP chamber masonary housing, with filling earthing compound powder inside GI pipe complete as per direction of site in charge complete.
463	SITC of M.S. Louver/ Flap/ Shutter for Exhaust Fan 12\\" (300mm) size with all fixing material, nut bolt etc. and T&P.
464	SITC of M.S. Louver/ Flap/ Shutter for Exhaust Fan 15\\" (380mm) size with all fixing material, nut bolt etc. and T&P.
465	SITC of M.S. Louver/ Flap/ Shutter for Exhaust Fan 18\\" (450mm) size with all fixing material, nut bolt etc. and T&P.
466	SITC of Thermoplastic Cable Junction Box IP 65 Dimensions (LXBXH) 155 x 210 x 92 mm with metric knockouts for cable entry suitable for 10-16 sq.mm PVC sheathed armoured cable with 5 pole Terminal Set and one no. 5-32A SP MCB 'C' Curved for cable connections fixed on support (DIN Rail) with provision of continuity of loop earthing between I/C & O/G cables as required, equivalent to Hensel Cat No.KF1616G (Make-Hensel / Siemens)
467	Supplying and fixing of Digital Ammeter equivalent to Make: Secure & Model DPM I310 in existing panel/DB complete with all connections, testing and commissioning etc as required.
468	Supplying and fixing of Digital Voltmeter equivalent to Make: Secure & Model DPM V310 in existing panel/DB complete with all connections, testing and commissioning etc as required.
469	Supplying and fixing of Digital Multifunction Meter equivalent to Make: Secure & Model Elite 102 in existing panel/DB complete with all connections, testing and commissioning etc as required.
470	SITC of 100/5- 600/5 CT burdan 15 VA, tap wound and ring type CL -1 complete with all connections including all mounting accessories in all respect.
471	SITC of LED Indicator 230V or more as required, AC/DC as required complete with all connections including all mounting accessories in all respect.
472	SITC of Wall mounting fan 400 mm Sweep revolving type with speed regulator.
473	SITC of 240 V, 150 MM sweep PVC body exhaust fan in existing opening and making good finish with plaster and all masonary work, connection with 1.5 sqmm PVC insulated, copper conductor, single core etc.
474	SITC of 240 V, 200 MM sweep PVC body exhaust fan in existing opening and making good finish with plaster and all masonary work, connection with 1.5 sqmm PVC insulated, copper conductor, single core etc.
475	SITC of 240 V, 250 MM sweep PVC body exhaust fan in existing opening and making good finish with plaster and all masonary work, connection with 1.5 sqmm PVC insulated, copper conductor, single core etc.
476	Supply, Installation, Testing and Commissioning of 900mm ceiling fan, service value ≥ 5.1 CM/Min/Watt, air delivery 130 CM/Min (Minimum), with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. metal ( Aluminum alloy) blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, steel/Al body Power Factor not less than 0.9, Service Value (CM/M/W) minimum as below, 350 RPM (tolerance as per IS : 374-2019), THD (Total Harmonic Distortion) less than 10%, suitable for operation with regulator for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Ceiling Fan compliant to IS 374:2019 fan Supply earthing etc. complete as required.
477	Do but 1200 mm ceiling fan service value ≥ 6.0 CM/Min/Watt, air delivery 210 CM/Min (Minimum)
478	Providing, laying and fixing B class medium ISI 50 mm dia G.I. pipe in ground complete with G.I. fittings including boring/ trenching (75 cm deep) and re-filling etc as required
479	.....do.....but G.I. Pipe 80 mm dia.
480	.....do.....but G.I. Pipe 100 mm dia.
481	Supplying and installing of 100 mm width X 50 mm depth X 1.6 mm thickness perforated Hot dipped Galvanised Iron cable trays (Galvanisation thickness not less then 50 microns) with perforation not more than 17.5% in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts etc as required.
482	.....do.....150 mm width X 50 mm depth X 1.6 mm thickness
483	.....do.....225 mm width X 50 mm depth X 1.6 mm thickness
484	Supplying and installing of 100 mm width X 50 mm depth X 1.6 mm thickness size of perforated Hot Dipped Galvanised Iron cable tray \\"bends\\" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with two numbers GI Suspenders i/c base of suitable size GI angle, GI bolts & nuts, fastner etc as required.
485	150 mm width X 50 mm depth X 1.6 mm thickness
486	225 mm width X 50 mm depth X 1.6 mm thickness
487	Supplying and installing of 100 mm width X 50 mm depth X 1.6 mm thicknesssize of perforated Hot Dipped Galvanised Iron cable tray \\"Tee\\" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with two numbers GI Suspenders i/c base of suitable size GI angle, GI bolts & nuts, fastner etc as required.
488	150 mm width X 50 mm depth X 1.6 mm thickness
489	225 mm width X 50 mm depth X 1.6 mm thickness
490	Supplying and installing of 100 mm width X 50 mm depth X 1.6 mm thickness size of perforated Hot Dipped Galvanised Iron cable tray \\"Cross member\\" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with two numbers GI Suspenders i/c base of suitable size GI angle, GI bolts & nuts, fastner etc as required
491	150 mm width X 50 mm depth X 1.6 mm thickness
492	225 mm width X 50 mm depth X 1.6 mm thickness
493	Supplying and installing of 100 mm width X 50 mm depth X 1.6 mm thickness size of perforated Hot Dipped Galvanised Iron cable tray \\"Reducer\\" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with two numbers GI Suspenders i/c base of suitable size GI angle, GI bolts & nuts, fastner etc as required
494	150 mm width X 50 mm depth X 1.6 mm thickness
495	225 mm width X 50 mm depth X 1.6 mm thickness
496	Supplying and installing of 50 mm width X 25 mm depth X 0.6 mm thickness perforated painted with powder coating Metal/ GI raceway with bracket for fixing raceway 50x25 mm, coupler for joining raceway with proper nut bolts as per site requirement with proper connection etc as required.
497	SITC of LED light fitting 600mm length minimum 1000Lumen with mounting rail box / aluminium extruded Batten suitable for surface, wall and conduit mounting with acessories and prewired with both side end cap equivalent to Wipro Cat no. LL20-111-XXX-65NE3. Minimum five years warranty should be provided.
498	Supplying, installation, Testing & Commissioning of LED Batten light 18- 22 Watt, Powder coated die cast /Extruded aluminiumBody (Thickness > 1.20 mm) (System lumen efficacy >135 lm/Watt) Supplying, installation, Testing & Commissioning of LED surface mounted Batten light of following body material and construction as per IS : 10322 with driver (Replaceable) as per the requirement with Driver efficiency >85% ,Operating voltage AC 140-270 Volt, frequency 50/60 hz, Operating temp range -5 0C to 40 0C, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P. F.≥0.95, IP20, CRI >80, Flicker free (flicker should be below 5 %), life time (LED, Driver & electrical circuitry), of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends, CCT 3000°K / 4000°K / 5700°K /6500°K (As per ANSI Bin), SDCM (Standard Deviation Color Matching) <3, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard. Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing complete in all respect i/c external connections with 1.5 sq mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy >135 lm/Watt output . LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted.. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminium housing such that LED junction temperature shall not rise above 90°C).
499	SITC of suspended mounting LED Light fitting minimum lumen 3600 including driver equivalent to Havells cat no. DESTG250LP/S36WLED857SWH1130 with End Cap & Suspension kit as required complete all connections.
500	Supplying, Installation, Testing & Commissioning of 12 -15 watt LED Down lighter (COB Type) (System lumen efficacy ≥120 lm/Watt ) Recessed/surface (Round / square/ Rectangular) COB Type of following body material and construction as per IS : 10322 with driver as per the requirement with Driver efficiency >85%, Operating voltage AC 140-270 Volt, frequency 50/60 hz, Operating temp range -5 0C to 40 0C, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P. F.≥0.95, IP20, CRI >80 , UGR (Unified Glare Rating) < 19, Flicker free (flicker should be below 5 %), life time (LED, Driver & electrical circuitry), life time of minimum 50000 Burning Hours with, 70% of initial Lumen maintained till life ends , CCT 3000°K / 4000°K / 5700°K /6500°K (As per ANSI Bin), SDCM(Standard Deviation Colour Matching) <3, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard. Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. \\"complete in all respect i/c external connections with 1.5 sq mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy ≥120 <135 lm/Watt output . LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted Shape size and CCT shall be as approved by Engineer-inCharge as per requirement. (Thermal management: heat sink of aluminium housing such that LED junction temperature shall not rise above 90°C). Powder coated die cast /Extruded aluminium Body including trim with Aluminium Reflector

Tender Documents

SR No	FileName	File Description
1	Click here to download tender document	Tender Documents
2	Click here to download tender document	Tender Documents
3	Click here to download tender document	Tender Documents
4	Click here to download tender document	Tender Documents

Also Visit

Tenders

Uttarakhand Tenders

Construction Tenders

Building Construction Tenders

Building Work Tenders

Disclaimer

We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.

Top

Tender For Extension Of The Second Floor With Lgsf Framing System, Including Electrical Works For The Powergrid Centre Of Excellence (Coe) At The Institute Computer Centre, Iit Roorkee, Roorkee-Uttarakhand

Tender Documents

Disclaimer

About Us

Services

Browse Tenders

For Sales Inquiry

Tender For Extension Of The Second Floor With Lgsf Framing System, Including Electrical Works For The Powergrid Centre Of Excellence (Coe) At The Institute Computer Centre, Iit Roorkee, Roorkee-Uttarakhand

Tender Documents

Disclaimer

OTP Verification

About Us

Services

Browse Tenders

For Sales Inquiry

Connect With Us