|
| 1 | SCHEDULE 'A' PART-I : BOQ OF WORKS FOR B/R WORKS. |
| 2 | Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/ slabs/ blankets, any thickness, including cover fillets, complete all as specified and as directed. |
| 3 | Dismantling of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings, complete all as specified and as directed. |
| 4 | Demolition of un-reinforced cement concrete in ground floors and pavings not exceeding 15 cm thickness (below or above ground level), ncluding cleaning, removal and disposal of rubbish/ waste materials from premises, complete all as specified and as directed. |
| 5 | Taking down of chowkhats or frame with shutters (without taking off shutters from the frames) area not exceeding 1.50 Sqm each, complete all as specified and as directed. |
| 6 | Taking down shutters of any descriptions area exceeding 1.00 Sqm but not exceeding 2.00 Sqm, complete all as specified and directed. |
| 7 | Pre-painted galvalume aluminium zinc coating galvanised iron based corrugated steel sheet 0.50mm of any colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specifed and directed. |
| 8 | Pre-painted galvalume aluminium zinc coating galvanised iron based plain steel sheet 0.50mm of any colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specifed and directed. |
| 9 | Dismantling structural steel work including doors, gates but excluding framed truss etc, complete all as specified and as directed. |
| 10 | Rolled mild steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS:1161-1979 grade St.-240, complete all as specified and as directed, complete all as specified and as directed. |
| 11 | Rolled mild steel sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates conforming to Fe-410 W (Gde E-250) quality B, complete all as specified and as directed. |
| 12 | Mild steel work in hand rails, half round or other steel section, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embedding in concrete and screwing etc. wind ties for roof including securing bolts; and similar work conforming to Fe-290 Gde E-165, complete all as specified and as directed. |
| 13 | Preparation of new or previously untreated steel surfaces of any description, not otherwise described, over 10cm width or girth including and applying two coats of synthetic enamel paint over one coat of zinc chrome/ red oxide primer, complete all as specified and as directed. |
| 14 | Preparation of old painted steel surfaces of any description, over 10cm width or girth including and applying one coat of synthetic enamel paint, complete all as specified and as directed. |
| 15 | Anodised aluminium snap grid frame work for false ceiling, powder coated, comprising of aluminium Tee (weight of section not less than 280 gms/mtr) and aluminium angle (weight of section not less than 280 gms/mtr), grid size 605x605mm, including Hangers 6.0mm dia, galvanised iron (upto1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of galvanised iron flat 40x3 mm size 60mm long and expansion hold fasteners 12.50mm dia, 40mm long, complete all as specified and as directed. |
| 16 | Providing and fixing everest board 4mm thick, designer, in ceiling fixed as per manufacturer’s instructions, grid size 595x595mm, for false ceiling all as specified, complete all as specified and as directed. |
| 17 | Excavation in post holes (or similar holes) each nor exceeding 0.50 Cum, getting out in any type of soil including returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 Cm, complete all as specified and as directed. |
| 18 | Plain cement concrete M-7.50(1:4:8), type D-2 (using 40mm graded crushed stone aggregate), as mass concrete in foundation filling, complete all as specified and as directed. |
| 19 | Plain cement concrete M-10 (1:3:6), type C-2 (using 40mm graded crushed stone aggregate), as mass concrete in foundation filling, complete all as specified and as directed. |
| 20 | Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and nontoxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and as directed.Note: Stainless steel butt hinges and necessary stainless steel screws shall be paid separately. |
| 21 | Factory made solid panel PVC door shutter 30mm thick, wood plastic composite (WPC) moulded gauged shutter with wire mesh in any number of divisions with brown wood grain texture including stainless steel wire mesh fixed with 15mmx15mm square tube in side rails with screwing 8mmx28mm heat metal zinc coated screws which can be refix again after replacement of stainless wire mesh as per requirement, complete all as specified and as directed. |
| 22 | Curtain rod, 20mm dia, mild steel, fancy type, any colour coated with fixing and inlcuing end knobs, fixing brackets, stops, round rings to hold the curtain, fixing with wall plugs and screws, complete all as specified and as directed. |
| 23 | Butt hinges, size 100mm, medium weight, cold rolled mild steel, and fixed, complete all as specified and as directed. |
| 24 | Aluminium anodised, barrel tower bolts of extruded Section, size 150mm long and fixed, complete all as specified and as directed. |
| 25 | Aluminium alloy, anodised, sliding door bolt, size 300mm, with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, complete all as specified and as directed. |
| 26 | Extruded aluminium alloy handles, fabricated type, anodised, size 150mm, complete all as specified and as directed. |
| 27 | Providing and fixing of powder coated aluminium three track sliding glazed window manufactured with approved aluminium section with three sliding shutter each shutter width one half of the length of window with the comprising the follow specifications and making good the adjacent surfaces of walls after fixing :-(i) Window’s aluminium frame of cross section 101mmx40mmx 1.50mm thick.(ii) Three way track for sliding shutters of cross sections 91.80mmx31.75mmx1.10mm thick.(iii) Sliding shutter frame of cross section 40mmx18mmx1.0mm.(iv) Aluminium glazing strip size 18.20mmx16.66mm.(v) 4.0mm thick float glass superior quality for both leafs.(vi) Rubber gasket/ beading for fixing glass panes.(vii) Locking cleats per shutter including rollers 01 Nos.(viii) 02 Nos. sliding rollers in each leaf.(ix) Fixing screws for frame with wall 06 per window.(x) Aluminium wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm for each shutter.(xi) Aluminium grill not less than 1.30 Kg/ Sqm weight along with border cleat. |
| 28 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and as directed. |
| 29 | Non-skid, coloured, ceramic tiles 7 to 8mm thick (square/ rectangular) area of each tile exceeding 0.18 Per Square Metre but not exceeding 0.38 Per Square Metre, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including laid over screed bed or bedding layer of mortar 15mm thick in cement mortar 1:6, complete all as specified and as directed. |
| 30 | Non-skid, coloured, ceramic tiles 7 to 8mm thick (square/ rectangular) area of each tile exceeding 0.18 Per Square Metre but not exceeding 0.38 Per Square Metre, in skirting or in vertical surfaces etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including fixed over screed bed or bedding layer of mortar 10mm thick in cement mortar 1:4, complete all as specified and as directed. |
| 31 | Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc, complete all as specified and as directed. |
| 32 | Rendering 15mm thick on fair faces of on brick work or concrete surfaces, in cement mortar 1:6, rendering is to be finished even and smooth (without using extra cement), complete all as specified and as directed. Please Enable Macros to View BoQ information |
| 33 | Rendering 15mm thick on fair faces of on brick work or concrete surfaces, in cement mortar 1:6, rendering is to be finished even and smooth (without using extra cement), complete all as specified and as directed. Please Enable Macros to View BoQ information |
