|
| 1 | Excavating over areas, n exc 1.5m deep and getting out in hard/ dence soil complete all as specified and directed. |
| 2 | Excavation in trenches n'exc 1.5 m width and n'exc 1.5 m in depth for foundation etc / for laying of cable/ pipe etc n'exc 10 sqm on plan and n'exc 1.5 m in depth and getting out in soft/loose soil complete all as specified and directed. |
| 3 | Excavation in trenches n'exc 1.5 m width and n'exc 1.5 m in depth for foundation or for shafts, well cesspits, manholes etc / for laying of cable/ pipe etc n'exc 10 sqm on plan and n'exc 1.5 m in depth and getting out in hard/dense soil complete all as specified and directed. |
| 4 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm. complete all as specified and directed. |
| 5 | Removal of surplus soil to a distance n'exc. 50 Mtr and depositing where directed at a level not exc 1.5m above the starting point complete all as specified and directed. |
| 6 | M&L for sand filling under floors or in foundations including watering and consolidation complete all as specified and directed. |
| 7 | M&L for PCC (1:4:8) Type D2 (40 mm graded aggre-gate) as in foundations, filling and mass-concrete or sub base of floor/ hard standing/ footpath complete all as specified and directed. |
| 8 | Demolition of RCC of any description and and in any position not otherwise specifically provided for etc including cutting of reinforcement to facilitate demolition including removal of rubbish out side MOD land complete all as specified and directed complete all as specified and directed. Note : Reinforcement obtained from demolition will be considered credit Sch as scrap iron. |
| 9 | M&L for RCC (design mix) M-25 (20mm graded aggregates) as in walls, retaining walls, basement walls, ballast walls and the like, any thickness; above top of footings including attached pilasters and buttresses complete all as specified and directed. |
| 10 | M&L for formwork for rough finish surface to sides of walls, retaining wall, basement wall etc. complete all as specified and directed. |
| 11 | M&L for mild steel TMT bars as in reinforcement, 10mm dia and over cut to length, bent to shape required including cranking, bending hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. |
| 12 | M&L for precast PCC (1:3:6) type C1 (using 20mm graded aggregate) solid block masonary work, straight or curved on plan exc 6m mean radius, built in CM (1:4) complete all as specified and directed. |
| 13 | M&L for precast PCC (1:3:6) type C1 (using 20mm graded aggregate) solid block masonary work, 100mm thick or slab 10cm thick (plain or interlockingjoints), straight or curved on plan exc 6m mean radius, built in CM (1:4) complete all as specified and directed. |
| 14 | Supply only WPC integral water proofing compound (Liquid type) complete all as specified and directed. |
| 15 | Demolition of PCC in ground floor and pavings not exc 15 cm thickness below or above ground level including removal of rubbish out side MOD land complete all as specified and directed. |
| 16 | M&L for PCC (1:2:4) type B-1, using 20mm graded stone aggregates, as in kerb/ benching/ coping, bed plates, for fixing of hold fast, water troughs and the like including weathering, slightly rounded or chamfered angles and throating including necessary formwork complete all as specified and directed. |
| 17 | M&L for 75 mm thick PCC (1:4:8) type D2, (40 mm graded stone agg) as in sub base of floor/ hardstanding/ footpath complete all as specified and directed. |
| 18 | M&L for 25mm thick PCC (1:2:4) type B0 (12.5 mm graded stone agg) as in sub floor of flooring complete all as specified and directed. |
| 19 | Roughening surface of old concrete floor by picking, sweeping cleaning and washing down with water to remove dust etc complete all as specified and as directed. |
| 20 | Taking down cement plaster on brick or stone wall surfaces including glazed tiles wherever exists including raking out joints, hacking for key and scrubbing down with water and removing unseviceable materials out side MoD land complete all as specified and as directed. |
| 21 | M&L for 15mm thick plastering on fair faces of brick wall in CM (1:4) surface finished even and fair complete all as specified and directed. |
| 22 | M&L for 10mm thick plastering on fair faces of brick wall in CM (1:4) surface finished even and fair complete all as specified and directed. |
| 23 | M&L for 10mm thick rendering on fair faces of brick/ PCC block masonary work or concrete surface in cement plaster (1:6) finished the surface even and fair complete all as specified and directed. |
| 24 | M&L for preparing old decorated plastered or unplastered surfaces of wall by complete removal and applying two coats of white wash complete all as specified and as directed. |
| 25 | M&L for preparing newly plastered surfaces of wall and applying three coats of white wash complete all as specified and directed. Note :- The newly plastered surface must be prepared in a manner so that there should not be any impression of dent and it should be made even and smooth all as per satifaction of Engr-in-Charge.The cost of all materials, T&P and labour required for preparation of surface are deemed to be included in the rates quoted. |
| 26 | M&L for preparing newly plastered surfaces of wall and applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489: 2004, alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10sqm over new surfaces as per manufacturer instruction complete all as specified and directed. |
| 27 | M&L for preparing old decorated plastered or unplastered surfaces of wall, pillasters, cornices etc by complete removal of existing treatment by scrapping, washing, rubbing down & stopping etc and applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489: 2004, alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10sqm over new surfaces as per manufacturer instruction complete all as specified and directed. |
| 28 | S&F in repair 5mm thick beveled edge best quality looking mirror of size 600x450 mm with 30 mm PVC beading all around the glass, mounted over 3mm thick PVC sheet or 6mm thick AC bldg board, complete all as specified and directed. |
| 29 | M&L for PCC (1:2:4) type B-1, using 20mm graded stone aggregate as in surface channel and drain including saucer drain and toe wall etc complete all as specified and directed. |
| 30 | M&L for extra for forming fair finished drain, or channel, 30 cm inner girth in cement concrete using extra cement including forms, moulds, mitred, stopped ends, complete all as specified and directed. |
| 31 | Add or deduct from item No. 68 for each 25 mmm girth or part thereof over or under 30Cm complete all as specified and directed.Note:- For adjustment only and quantities may be varied (Plus/Minus) to any extend as per site requirement. |
| 32 | Taking down aluminium chowkhats or frames with shutters ( without taking off shutters from the frames) of following size complete all as specified and directed:- |
| 33 | Area not exc 1.5 sqm each |
| 34 | Area exc 1.5 sqm but not exc 4 sqm each |
| 35 | Taking down PVC chowkhats or frames with shutters ( without taking off shutters from the frames) of following size complete all as specified and directed:- |
| 36 | Area not exc 1.5 sqm each |
| 37 | S&F Powder coated aluminium (minimum thickness of powdercoating 50 micron) frame for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z-sections and other sections of approved make conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc, aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws complete all as specified and directed. |
| 38 | S&F Powder coated aluminium (minimum thickness of powdercoating 50 micron) work for shutters of doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z-sections and other sections of approved make conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc, aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws complete all as specified and directed. |
| 39 | S&F powder coated aluminium grill (minimum thickness of powder coating 50 micron)) of approved design/ pattern, with approved standard section and fixed to the new or existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening complete all as specified and directed. |
| 40 | S&F solid PVC door frame of size 50mm x 47 mm made out of 5 mm plain colour PVC sheet, reinforced with MS square tube, fixing in same opening complete as all as specified and directed. |
| 41 | S&F factory made solid PVC moulded door shutter 28 to 30mm thick (Style) with 2, 4 or 6 raised panel desaign with 2mm thick moulded prelam PVC sheet on the front face and 2mm prelam PVC sheet on back face with and including frame as per SSR-2009 specification and drawing complete all as specified and directed. |
| 42 | M&L for two coats of synthetic enamel paint over a coat of red oxide primer including preparation of new steel surface over 10cm width or grith complete all as specified and directed. |
| 43 | S&F extruded aluminium alloy handles, fabricated type, anodised (ISI marked) of following size complete all as directed and specified:- |
| 44 | 100 mm long |
| 45 | 75 mm long |
| 46 | S&F powder coated aluminium barrel tower bolts of extruded section of following size complete all as directed and specified:- |
| 47 | 150 mm long |
| 48 | S&F anodised aluminium barrel tower bolts (ISI marked) of extruded section of following size complete all as directed and specified:- |
| 49 | 75 mm long |
| 50 | S&F powder coated aluminium sliding door bolt with hasp, staple ( bolt type ) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections of following size complete all as specified and directed:- |
| 51 | 300mm long |
| 52 | S&F 100 mm long butt hinge, extruded aluminium alloy with galvanized mild steel hinge pin, powder coated of required tint to match shutter and fixed, type B-21 complete all as specified and directed. |
| 53 | Supply only aluminium aloy wire cloth 0.45mm nominal dia of wire and average width of aperture 1.4mm fixed with tinned tacks or wire staples complete all as specified and as directed. |
| 54 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed. |
| 55 | S&F rolled mild steel section for structural steel work as in main and cross beams, hip and jack rafters, purlin where connected to common rafters and running rails and guides for sliding crane, fixed with angle cleats or other connecting plates/ bolts, conforming to Fe-290(Gde-E-165) complete all as specified and as directed.Note : The rates quoted allow for cutting to dead length where required, notching, drilling, fitting, riveting and/or welding or connecting with bolts and nuts (including rivets or bolts and nuts), providing and fitting angle cleats, fish plates, gusset plates etc., also for wedging, plumbing, truing up and fixing complete. |
| 56 | S&F rolled mild steel section for roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc., conforming to Fe-410-W(Gde-E-250) quality-A complete all as specified and as directed.Note : The rates quoted allow for cutting to dead length where required, notching, drilling, fitting, riveting and/or welding or connecting with bolts and nuts (including rivets or bolts and nuts), providing and fitting angle cleats, fish plates, gusset plates etc., also for wedging, plumbing, truing up and fixing complete. Please Enable Macros to View BoQ information |
| 57 | S&F rolled mild steel section for roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc., conforming to Fe-410-W(Gde-E-250) quality-A complete all as specified and as directed.Note : The rates quoted allow for cutting to dead length where required, notching, drilling, fitting, riveting and/or welding or connecting with bolts and nuts (including rivets or bolts and nuts), providing and fitting angle cleats, fish plates, gusset plates etc., also for wedging, plumbing, truing up and fixing complete. Please Enable Macros to View BoQ information |
