|
| 1 | Taking down cement plaster on brick or concrete surfaces including racking out joints hacking for keys scrubbing down with water etc complete all as specified and as directed by Engineer-in-Charge. |
| 2 | Dismantaling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing servicable tiles to store and rubbish off premises complete all as specified and as directed by Engineer-in-Charge. |
| 3 | Taking down chowkats with shutter (without taking off shutters from the frames) exc 1.5 sqm but n exc 4 sm each, complete all as specified and as directed by Engineer-in-Charge. |
| 4 | Taking down shutter of any description exc 1sqm each and n exc 2Sqm each, complete all as specified and as directed by Engineer-in-Charge. |
| 5 | Taking down Chowkats or Frames, not exc. 1.50 Sqm Each with Shutters (without Taking Off Shutters from the Frames), complete all as specified and as directed by Engineer-in-Charge. |
| 6 | Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any mortar complete all as specified and as directed by Engineer-in-Charge. |
| 7 | Demolition Cement Concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level complete all as specified and as directed by Engineer-in-Charge. |
| 8 | Demolition of brick work or stone/boulder masonary built in CM including all quoins, arches, pillars, etc but excluding ashlar, facing, dressed stone work and pre-cast concrete articles complete all as specified and as directed by Engineer-in-Charge |
| 9 | Rendering 10mm thick on fair faces on brick masonary or concrete surfaces in cm 1:6 finished complete all as specified and as directed by Engineer-in-Charge. |
| 10 | M&L for Prepration of newly plastered on walls by hand held sander / long handle sander including cornices, pilasters etc complete all as specified directed and applying two coat of oil bound distemper over a coat of alkali resistant priming paint, over a coat 3mm thick wall care putty on walls complete all as specified and as directed by Engineer-in-Charge. |
| 11 | M&L 15 mm thick rendering on other than fair faces of external wall of brick/ stone / block masonary or concret surfaces in two layers Ist layer shall be 10mm in cm 1:6, secound and final layer shall be 5mm thick in CM 1:4 finished fair and even without using extra cement mixed with integral water proofing compound complete all as specified and as directed by Engineer-in-Charge. |
| 12 | M&L Prepration of newly plastered surface of wall by hand held sander / long handle sander including cornices, pilasters etc and appliying with Airless spray two or more coats of 100 % premium acrylic emulsion paint having VOC less than 50gm/litre and UV resistance as per IS 15489-2004, Alkali & fungal resistance dirt resistance exterior paint of required shade (company Depot Tinted) with silicon additives @1.43 litre/10Sqm over and including priming coat of exterior primer applied @ 0.9 ltr/10sqm complete all as specified and as directed by Engineer-in-Charge. |
| 13 | M&L for Prepration by hand held sander / long handle sander including cornices, pilasters etc of newly plastered on wall complete all as specified directed and applying three coat of white wash, complete all as specified and as directed by Engineer-in-Charge. |
| 14 | M&L 5 mm thick rendering on ceiling or concrete surfaces in cm 1:3 finished complete all as specified and as directed by Engineer-in-Charge. |
| 15 | M&L for Prepration by hand held sander / long handle sander including cornices, pilasters etc of newly plastered on ceiling complete all as specified directed and applying three coat of white wash, complete all as specified and as directed by Engineer-in-Charge. |
| 16 | M&L complete removal of existing tretment by hand held sander / long handle sander washing down with Jet washer and appliying Airless spray two or more coats of 100 % premium acrylic emulsion paint having VOC less than 50gm/litre and UV resistance as per IS 15489-2004, Alkali & fungal resistance dirt resistance exterior paint of required shade (company Depot Tinted) with silicon additives @1.43 litre/10Sqm over and including priming coat of exterior primer applied @ 0.9 ltr/10sqm |
| 17 | Complete removal of existing treatment of old surfaces of wall including preparation of surfaces by hand held sander / long handle sander including cornices, pilasters etc and applying two coats of oil bound distemper over a coat of alkali resistant primer over a coat of wall care putty complete all as specified and as directed by Engineer-in-Charge. |
| 18 | M&L Preparation of old surfaces of wall removing nails including scraping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots etc by hand held sander / long handle sander including cornices, pilasters etc (Plastered or unplastered surfaces) , filling undulation and holes with putty and applying one coat of oil bound distemper with roller finish complete all as directed.on walls etc.complete as specified and as directed by Engineer-In-Charge. |
| 19 | Preparation of old plastered surfaces of ceiling by hand held sander / long handle sander including cornices, pilasters etc and applying one coat of white wash complete all as specified and as directed by Engineer-in-Charge. |
| 20 | Preparation of old plastered surfaces of wall surface by hand held sander / long handle sander including cornices, pilasters etc and applying one coat of white wash complete all as specified and as directed by Engineer-in-Charge. |
| 21 | M&L preparation of old wooden surfaces of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed by Engineer-in-Charge. |
| 22 | Complete removal of existing roof treatment, removing rubbish off the premises, cleanning the surface and preparing to receive new roof treatment and applying roof treatment as under:- (a) Applying coat of bituminios primer @ 0.40 litre/ Sqm on prepared surfaces and allow to dry(the primer and the membrane to be used shal be of same manufacturer, (b) Supply and laying of minimum 3 mm thick APP modified polymeric membrane weighting not less than 3 KG/ Sqm black finish reinforcement with non woven polyster matt with help of torching with proplane or abutance gas using torch with minimum 75 mm side overlap and 100 mm end overlap. (c) all overlaps and joints shall be sealed as per manufacturers instruction complete all as specified and directed. (d) two coat of approved bituminus aluminium paint over roof treatment/ membrane complete all as specified and as directed by Engineer-in-Charge. |
| 23 | Roughening surfaces of old concrete surfaces by picking, sweeping clean and washing down with water to remove dust, etc incl brushing neat cement slurry with 3.0 kg of cement per sq metre complete all as specified and as directed by Engineer-in-Charge. |
| 24 | M&L for Cutting out cracks to V-section in existing roofs or terracing, cleaning out, wetting, grouting with cement and sand slurry 1:3 complete all as specified and as directed by Engineer-in-Charge. |
| 25 | M&L for Rendering 10 mm thick in CM(1:3) with using water proofing compound on fair faces of brick work/ Fasia and roof surface finished even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge. |
| 26 | M&L PCC 1:2:4, type B0 (using 12.5mm size stone aggregate) as levelling course complete all as specified complete all as specified and as directed by Engineer-in-Charge. |
| 27 | S & F PVC door with chowkhats frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, supply & fixing in opening as per specification & drawing complete all as specified and as directed by Engineer-in-Charge. |
| 28 | S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C' channel heaving a PVC sheet strip of 20mm width suck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing complete all as specified and as directed by Engineer-in-Charge. |
| 29 | M/L 2nd class Hardwood chowkhats, plain, solid, straight, wrought, framed, rebate on the solid,rounded or chamfered put together with glue pinned at joints complete all as specified and as directed by Engineer-in-Charge. |
| 30 | M&L for Hold fast for fixing of chowkats and similar work con- forming to Fe.290.Gde-E-165, complete all as specified and as directed by Engineer-in-Charge. |
| 31 | Providing cement concrete 1:2:4 type BO (12.5mm graded aggregate) in cills, steps, seismic and other similar bands plinth coureses string courses lacing courses parapets and railing copings kneelers apex bed plates kerbs. etc.. water troughs and the like including wethering slightly rounded or chamfered angles and throating complete all as specified and as directed by Engineer-in-Charge. |
| 32 | S&F 35 mm thick 2nd class hard wood factory made plain framed, panelled shutters (any number of panel ) with lock rail and panel of 12 mm thick veneered particle board with commercial veneering on both faces. The size of rail and styles as per IS-1003 as per IS 1003 part -I , kiln seasoned and chemically pressure treated complete all as specified and as directed by Engineer-in-Charge. |
| 33 | S&F Glazed and skelton shutters, 35 mm thick of Second class hard wood open rebated and prepared to receive glass, gauge etc without sash bars) edges of framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass, etc, sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.24(a), chemically treated, complete all as specified and as directed by Engineer-in-Charge. |
| 34 | S&F 25mm thick factory made Plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats of steel or wooden complete all as specified and as directed by Engineer-in-Charge. |
| 35 | S&F powder coated anodised aluminium fixed louvered ventilator frame of size 63.5 x 38.1 x 1.01 mm thick or equivalent section fixed in vertical position with aluminium vertical members and half portion to be provided with 4 mm thick pinhead glass and remaining portion to be louvered using 4 mm thick pinhead glass and louvered portion covered with stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm incl necessary channel frame work, including rubber gasket and aluminium beading including taking down old ventilator in any size and make complete all as specified and as directed by Engineer-in-Charge.Note : rates shall include all glazing/aluminium wire cloth, rubber packing, joining, cleats, glazing clips, aluminium snap beading etc complete all as specified and as directed by Engineer-in-Charge. |
| 36 | M&L for preparation of old steel surfaces of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed by Engineer-in-Charge. |
| 37 | S&F S/s door magnets/ catcher for cupboards , fixed with screws complete all as specified and as directed by Engineer-in-Charge. |
| 38 | S/F in repairs for Block boards, 18/19mm thick grade 2 quality, interior grade, decorative type with veneer/lamination as approved on both face fixed with screws to timber and frame work complete all as specified and as directed by Engineer-in-Charge. |
| 39 | S&F in repairs for external teak wood lipping, 18-19mm thick block board or veneered particle board , fixed with nails complete all as specified and as directed by Engineer-in-Charge. |
| 40 | S&F 30mm width of flap continuous (piano) hinges, mild steel, bright finish complete all as specified and as directed by Engineer-in-Charge. |
| 41 | S&F 300mm mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and as directed by Engineer-in-Charge. |
| 42 | S&F Floor door stopper of aluminium alloy body and tongue, anodised, 140 mm with hard drawn steel spring, fixed in floor complete all as specified and as directed by Engineer-in-Charge. |
| 43 | S&F in repairs stainless steel wire cloth 0.36mm dia of wire and avarage width of aperture 1.40mm and fixed with stainless steel wire staple in any type of windows/doors (aluminium or steel or wooden frame) complete all as specified and directed by Engineer-In-Charge. |
| 44 | S&F stainless steel wire cloth 0.36mm dia of wire and avarage width of aperture 1.40mm and fixed with stainless steel wire staple in any type of windows/doors complete all as specified and directed by Engineer-In-Charge. |
| 45 | M/L two coats of synthetic enameled painting over a coat of pink primer to new wooden surfaces of any description exc 10 cm width or girth complete all as specified and as directed by Engineer-in-Charge. |
| 46 | S&F Mild Steel Butt hinges, heavy weight, cold rolled, of size 100 mm complete all as specified and as directed by Engineer-in-Charge. |
| 47 | S&F aluminium anodised, barrel tower bolt of extruded section 150mm long complete all as specified and as directed by Engineer-in-Charge. |
| 48 | S&F 125 mm long aluminium handle, cast type, anodised complete all as specified and as directed by Engineer-in-Charge. |
| 49 | S&F aluminium anodised, barrel tower bolt of extruded section 100mm long, complete all as specified and as directed by Engineer-in-Charge. |
| 50 | S&F 100 mm long aluminium handle, cast type, anodised complete all as specified and as directed by Engineer-in-Charge. |
| 51 | S&F aluminium alloy anodised sliding door bolt with hasp staple(bolt type) ,250 mm long,and fixing clip of sheet cast or extruded section or fixing bolt cast aluminium alloy and fixed complete all as specified and as directed by Engineer-in-Charge. |
| 52 | S&F Aluminium anodised 75mm hasp and staple ,safety type with hinge pin including bolt to hinge plate and fixed with screws complete all as specified and as directed by Engineer-in-Charge. |
| 53 | M&L for screed bed or bedding 15mm thick in CM 1:4 on floor to receive tile complete all as specified and as directed by Engineer-in-Charge. |
| 54 | S & F Non Skid Ceramic Colour Tiles 7 to 8 mm thick area of each tiles exc 0.06 Sqm but n. exc 0.11 Sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed by Engineer-in-Charge. |
| 55 | S & F vitrified tiles 8 to 10 mm thick area of each tiles n exc 0.36 Sqm in floor , skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed by Engineer-in-Charge. |
| 56 | M&L 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including 20mm screed bed in CM 1:4 complete all as specified and as directed by Engineer-in-Charge. |
| 57 | M&L for 18-20mm thick Kota stone slab machine cut, in stair treds, bathroom platforms, shelf platforms etc. bedded and jointed with grey cement slurry mixed with pigment to match the shade of the slab including grinding, rubbing and polishing complete over and including 15 mm thick screed bed in CM 1:4 and polishing complete all as specified and directed by Engr-in-charge. |
| 58 | M&L for 18-20mm thick Kota stone slab machine cut, in riser of steps, skirting, dado and pillar etc. bedded and jointed with grey cement slurry mixed with pigment to match the shade of the slab including grinding, rubbing and polishing complete over and including 10 mm thick screed bed in CM 1:3 and polishing complete all as specified and directed by Engr-in-charge. |
| 59 | Moulding to kota stone slab/ granite including rounding off edges for 20 mm thick slabs including grinding and polishing complete all as specified and as directed by Engineer-in-Charge. |
| 60 | M&L rendering 10 mm thick in CM 1:3 on wall to receive tile complete all as specified and as directed by Engineer-in-Charge. |
| 61 | M& L glazed ceramic coloured tile in vertical surfaces 300x450x7 mm thick set and jointed in neat cement slurry and poited in white or coloured cement to match complete all as specified and as directed by Engineer-in-Charge. |
| 62 | M&L for 75mm thick cement concrete 1:3:6, Type C-2 ( Using 40mm graded aggregate) as in plinth protection , subbase complete all as specified and directed by Engr-in-charge. |
| 63 | Taking up or down steel tubing and connections including bore of pipe 25 mm complete all as specified and as directed by Engineer-in-Charge. |
| 64 | Supplying and laying of 25 mm outer dia CPVC pipes SDR 11 and plain CPVC SDR 11 fittings, concealed joint with CPVC adhesive taflon tape in any requirement complete to walls and ceilings or laid in floors iincluding all connected brass cpvc fittingsand cutting grooves, filled with CM1:6 complete all as specified and as directed by Engineer-in-Charge. |
| 65 | Taking up or down steel tubing and connections bore of pipe 20 mm complete all as specified and as directed by Engineer-in-Charge. |
| 66 | Supplying and laying of 20 mm outer dia CPVC pipes SDR 11 and plain CPVC SDR 11 fittings, concealed joint with CPVC adhesive taflon tape complete to walls and ceilings or laid in floors including all connected brass cpvc fittings and cutting grooves, filled with CM1:6 complete all as specified and as directed by Engineer-in-Charge. |
| 67 | Taking up or down steel tubing and connections bore of pipe 16 mm complete all as specified and as directed by Engineer-in-Charge. |
| 68 | Supplying and laying of 16 mm outer dia CPVC pipes SDR 11 and plain CPVC SDR 11 fittings, concealed joint with CPVC adhesive taflon tape in any requirement complete to walls and ceilings or laid in floors iincluding all connected brass cpvc fittingsand cutting grooves, filled with CM1:6 complete all as specified and as directed by Engineer-in-Charge. |
| 69 | Dismantling exc 250 & n exc 500 ltrs water tanks and removing from site complete all as specified and as directed by Engineer-in-Charge. |
| 70 | S & F in repairs 500 liters rotaional moulded polyethylene water storage tank, double layered (cylindrical vertical with closed top cover) as per IS-12701-1996 and PTMT 20mm ball valves/ float valve high pressure with epoxy aluminium rod and high density plastic ball screwed for iron pipe and fixed (minimum weight 20mm - 210 gms) , hoisted and fixed in position including necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc, complete as specified in SSR Part-I complete all as specified and as directed by Engineer-in-Charge. |
| 71 | S&F in repairs 20 mm dia gun metal, globe or gate valve, with iron wheel head, screwed both ends for iron pipe/upvc pipe complete all as specified and as directed by Engineer-in-Charge. |
| 72 | S&F in repair fancy type Bib taps, cast copper alloy 15mm dia with long handle, screwed down, screwed for iron pipe incl female brass threaded adaptor on CPVC pipes complete all as specified and as directed by Engineer-in-Charge. |
| 73 | S&F in repair Fancy type Stop valves angle /concealed 15mm bore, cast copper alloy, screwed down, high pre-ssure, with crutch or but-terfly handle, screwed both ends for iron pipe or for unions and fixed incl female brass threaded adaptor on CPVC pipes complete all as specified and as directed by Engineer-in-Charge. |
| 74 | S&F in repair 15mm fancy type Pillar taps, cast copper alloy, with long heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and as directed by Engineer-in-Charge. |
| 75 | S&F PVC connections 15mm size with PTMT nuts of length 600mm complete all as specified and as directed by Engineer-in-Charge. |
| 76 | S&F in repairs PVC(SWR) pipe 110 mm dia, conforming to IS-13592-1992 type 'B', single socketed in any length with rubber ring joints, fixed to wall complete all as specified and as directed by Engineer-in-Charge. |
| 77 | S & F PVC (SWR) junction single (single T) equal or unequal 110mm bore, with access door complete all as specified and directed by Engr-in-charge. |
| 78 | S&F in repair PVC (SWR)110 mm bend bore bends with access door any radius complete all as specified and as directed by Engineer-in-Charge. |
| 79 | S&F in repairs PVC(SWR) pipe 75 mm dia, conforming to IS-13592-1992 type 'B', single socketed in any length with rubber ring joints, fixed to walls complete all as specified and as directed by Engineer-in-Charge. |
| 80 | S&F in repairs PVC(SWR) bend any radius, 75 mm dia complete all as specified and as directed by Engineer-in-Charge. |
| 81 | S & F PVC (SWR) junction single (single T) equal or unequal 75mm bore, without access door complete all as specified and directed by Engr-in-charge. |
| 82 | S & F PVC (SWR) junction double (single T) equal or unequal 75mm bore, without access door complete all as specified and directed by Engr-in-charge. |
| 83 | M&L for cement concrete 1:2:4 type B-0 (12.5 mm aggregate) sub base of floors , mass concrete complete all as specified and directed by Engr in charge. |
| 84 | M & L in repairs 75mm outlet dia PVC(SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and as directed by Engineer-in-Charge. |
| 85 | S & F in repair vitreous china wash down water closet pan (pedestral pattern) white including fixing to flushing cistern and flush pipe and plastic water closet seat cover black closed pattern with flat bottom and cover and mild steel hinging device complete all as specified and as directed by Engineer-in-Charge. |
| 86 | S&F in repair vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern ) including provision of cement concrete bedding, connection to trap and to flushing pipe, anti syphonage pipe etc complete making good to floor complete all as specified and as directed by Engineer-in-Charge. |
| 87 | S&F in repair PVC flushing cistern, white, 10ltr capacity with 32mm dia flush pipe any lenth fixed to water closed complete all as specified and as directed by Engineer-in-Charge. |
| 88 | S & F in repair Vitreous China wash basin, white, flat back, size 550mm x 400 mm with & including a pair of cast iron brakets embedded in PCC 1:3:6) type C-1 (using 20mm graded stone aggregate), blocks of size 10x7.5x15cm , and 32 mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts,flange end bedded in red lead cement and other end fixed, ( excluding tap ) including PVC Waste coupling of PTMT 32mm dia (half or full threaded) Minimum weight 45gms , washers and Brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed complete as specified and directed by Engr-in-Charge. |
| 89 | S&F in repairs Stainless steel sink with draining board, made out of 1.00mm thick sheet for kitchen or laboratory with plug, washers waste pipe, including beding in cement mortar on to dwarf walls, or cast iron cantilever brackets, connecting union to waste pipe upto sqm each , overall size 915mmx460mm with bowl size 410mm x 330mm x 160mm complete including removing exixting sink complete all as specified and as directed by Engineer-in-Charge. |
| 90 | S&F in repairs glass corner shelf 300 mm (with ABS Bracket 300x 600) as selected including removing existing shelf complete all as specified and as directed by Engineer-in-Charge. |
| 91 | S&F in repair Soap dish of any type (S/S) approximate size 160x160 fixed to plugs with chromium plated brass screws including taking down old complete all as specified and as directed by Engineer-in-Charge. |
| 92 | S&F in repair Brass chromium plated Tublar towel rail 20mm dia D type 60 cm long between flanges complete all as specified and as directed by Engineer-in-Charge. |
| 93 | S&F 600 x 450mm bevelled edge mirror of selected quality glass mounted on 6mm thick AC building board or commercial plywood & fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and as directed by Engineer-in-Charge. |
| 94 | S&F in repair Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and as directed by Engineer-in-Charge. |
| 95 | S&F in repair 125 mm Brass chromium plated shower rose with or without swivel joints, any size, including fixing to steel pipe or union, complete all as specified and as directed by Engineer-in-Charge. |
| 96 | S&F in repair 25mm dia stainless steel curtain rail, cut in required length and size to fit with opening incl fixing on bracket with necessary screws fitted on bracket and decorative nobs on sides with necessary arrangement complete all as specified and as directed by Engr-in-charge. |
| 97 | S&F in repairs curtain rod side brackets of stainless steel, angular or cantilever type fixed to wall with 02 nos screws on each bracket and fitted screws for fixing curtain rod incl CP/stainless steel carved decorative design plain metal colour nobs with fixing arrangement for curtain rod using a screw complete all as specified and as directed by Engineer-in-Charge. |
| 98 | M&L for racking of cracks upto 5 mm wide ,preparation and crack filling with ready to use crack fiber reinforced filler /chemical based crack fillers by approved manufacturer and filling as per manufacturer instructions in walls,roofs of any type or size complete all as specified and as directed by Engineer-in-Charge. |
| 99 | M&L for racking of cracks exc 5 mm but not exc 10mm wide ,preparation and crack filling with ready to use crack fiber reinforced filler /chemical based crack fillers by approved manufacturer and filling as per manufacturer instructions in walls,roofs of any type or size complete all as specified and as directed by Engineer-in-Charge. |
| 100 | M&L 15mm thick rendering in cement plaster 1:3 with WPC on bottom and side walls of sunken floor incl finished even and smooth w/o using extra complete all as specified and as directed by Engineer-in-Charge. |
| 101 | Removing the plant/growth of any description size, any location of external surfaces of walls shafts by cutting & remvoing the roots completely spraying the suitable chemical (each plant 100 ML) in the removed portion to avoid re-growth & making good damaged portion to match the existing surfaces by PCC type B0 (1:2:4) 12.5 mm graded aggregate complete all as specified and as directed by Engineer-in-Charge. |
| 102 | Removal of all loose/unsound/bad/damaged concrete or plaster existing RCC structure of slab/beams/walls/chajja by using chesel/hammar .Cut and remove unsound reinforcement bars, wires etc without damaging the sound reinforcement . clean loose rust from bars manually with brush . fixing new supplymentary bars if required,either by tying it with existing bars or by welding on it. Applying eppoxy bonding agent and making good with polymer modified plaster/micro concrete as required thickness over a coat of rust removing alkaline primer and match the finishing to the existing surface in ground floor including formwork complete all as specified and as directed by Engineer-in-Charge. |
| 103 | M&L Cleaning vertical and horizontal surfaces of sunken slab using wire brushing followed by sanding with emery paper for loose materials/dust and applying two coats of epoxy resin component solution/mix using nylon brush pouring Base part in appropriate container followed by the Hardner part and mix thoroughly to attain homogeneous smooth paste and dilute the mixed compound with water in ratio 1 part Base: 1 part Hardner: 1 part water by slow addition and mix thoroughly until a brushable consistency is obtained, first coat will be allowed to dry for 6 to 8 hrs before application of second/final coat) incl curing treated surface for 24 hrs complete incl applying evenly a coat of blown bitumen @ 1.5kg/sqm over entire treated surfaces incl spout holes complete and all as specified as per manufacturer instruction complete all as specified and as directed by Engineer-in-Charge. |
| 104 | M&L for 40 mm thick PCC 1:2:4 type B-0 using 12.5 mm graded stone aggregate mixed with liquid water proofing compound as per manufacture instruction in bottom of sunken floors floors complete all as specified and as directed by Engineer-in-Charge. |
| 105 | Supply only of Intergral water proofing compound as per manufactures instruction complete all as specified and as directed by Engineer-in-Charge. |
| 106 | Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc. and making good, cutting exceeding 20cm girth on brick walls complete all as specified and as directed by Engineer-in-Charge. |
| 107 | M&L for Brickwork with fly ash moudular bricks built in CM (1:4) , straight or curved on plan exc 6m mean radius, complete all as specified and as directed by Engineer-in-Charge. |
| 108 | S&F in repairs 2 in 1 wall maounted mixer (15 mm bore) with quater turn fittings and provision for overhead shower with 115 mm bend pipe and wall flange, cast copper alloy with capstan heads, fancy type chromium plated (robotic electroplating for everlasting lustrous shine) with 2 water volume adjustment knobs one both side to control the flow of temperature ,screwed down, screwed for iron pipe or for brass ferrule and fixed includng neccesary fittings complete for mixing hot and cold water for tap and shower complete all as specified and as directed by Engineer-in-Charge. |
| 109 | Refixing of shutters of any description exc 1.0 sq. m but n exc 2.0 sq. m to same opening with necessary welding/ screws as per site requirement complete all as specified and as directed by Engineer-in-Charge. |
| 110 | S&F 40 mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finished complete all as specified and as directed by Engineer-in-Charge. |
| 111 | Hard core of guage n.exc 63mm deposited spread and levelled in layers n exc 15cm thick watered and rammed to a true surface complete all as specified and as directed by Engineer-in-Charge. |
| 112 | M & L 100mm thick PCC 1:4:8 type D2 (using 40mm graded stone aggregates) as in sub base, flooring , mass concrete etc complete all as specified and as directed by Engineer-in-Charge. |
| 113 | M&L for Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand complete all as specified and as directed by Engineer-in-Charge. |
| 114 | Exacavation in trenches not exc 1.5mtr wide and n exc 1.5mtr depth for foundation, manhole etc not exc 10 Sqm on plan including getting out in soft/loose soil in foul smell condition complete all as specified and as directed by Engineer-in-Charge. |
| 115 | S&F in repairs PVC(SWR) pipe 110 mm dia, conforming to IS-13592-1992 type 'B', single socketed in any length with rubber ring joints,laid in trenches or in floors complete all as specified and as directed by Engineer-in-Charge. |
| 116 | S&F in repair PVC (SWR)110 mm bend bore bends without door complete all as specified and as directed by Engineer-in-Charge. |
| 117 | M&L for concrete bed to drain pipes for 100mm bore SGSW/PVC SWR drain pipe in cm 1:4:8 type D-2, using 40 mm graded stone aggregate including packing under and haunching against the sides of pipes in foul smell condition complete all as specified and as directed by Engineer-in-Charge. |
| 118 | Returning, refiiling including spreading, leveling watering and well ramming in layers not exc 25cm in soft/loose soil complete all as specified and as directed by Engineer-in-Charge. |
| 119 | Removing excavated surplus soil/material not exc 50mtr and depositing where directed at a level not exc 1.5mtr above the starting point complete all as specified and as directed by Engineer-in-Charge. Please Enable Macros to View BoQ information |
