|
| 1 | Taking down chowkhat or frame (without taking off shutter from the frame) not exceeding 1.5 Square Metre each , removing from the site Cutting holes exc 150 Sq.cm but n.exc 400 Sq.cm in super facia area into or through brick walls built in mud mortar and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-l as required complete all as specified and as directed. |
| 2 | Taking down chowkhat or frame (without taking off shutter from the frame) exceeding 1.5 sqm and not exc 4.00 sqm each , removing from the site Cutting holes exc 150 Sq.cm but n.exc 400 Sq.cm in super facia area into or through brick walls built in mud mortar and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-l as required complete all as specified and as directed. |
| 3 | Taking down shutter of any description exc 1 Sqm and not exc 2 Sqm each complete all as specified and as directed. |
| 4 | M & L for Powder coated (minimum thickness of powder coating 50 micron) aluminium frame for doors , windows , ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed. |
| 5 | M & L for Powder coated (minimum thickness of powder coating 50 micron) aluminium window and ventilator (adequate track)/Shutter without sash, aluminium section weighing 0.55 kg/m including joining cleats, glazing clips, rubber neoprene packing, necessary powder coated hardware ie. handles, barrel tower bolts, hinges etc, powder coated aluminum snap beading, screws etc. complete all as specified and directed Note : Panel filling ie. glass, fibre sheet, board, wire mesh etc. shall be measured and paid for separately. |
| 6 | S&F Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-Charge. |
| 7 | S&F pressed steel frames of size 125 X 60 mm with rebate on both side including necessary fixing lugs hinges, locks strike plate etc (thickness of sheet shall be 1.25mm) and making good the plaster of wall in CM 1:6 complete all as specified & directed. |
| 8 | M&L for PCC 1:2:4 type B-0 (using 12.5mm grade stone aggregate) as in filling of Chowkhats or pressed steel door frame, in bed block and like, etc complete all as specified and directed. |
| 9 | S&F 30 mm thick Flush shutters ,soild core construction ,with paticle board core and plywood face panels , commercial type both face is covered with decorative face veneer with lipping /frame to match and complete all as specified and directed. |
| 10 | M & L for 35 mm thick glazed and skeleton shutters of 2nd class Hard Wood, open rebated and prepare to reveive glass, guage etc (without sash bars ) edges of framing plain chamfered or rounded, fitted with moulded beads both sides for securing glass etc, size of members of shutters as specified complete all as specified and directed. |
| 11 | M&L preperation of new wooden surface and applying two coat of synthetic enamel paint over a coat of pink primer on new wooden surface any description not otherwise described over 10 cm width or girth and complete all as specified and directed. |
| 12 | S&F in repair for floor door stopper of brass body and tongue, overall length of cover plate 150 mm , anodized, with hard drawn steel spring , fixed to shutters complete all as specified and as directed. |
| 13 | Supply & Fixing solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube fixed in opening as per specification & drawings complete all as specified and as directed. |
| 14 | S &F for factory made solid panel PVC door shutter 30mm thick ( style) consisting to frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Penelling of plain colour PVC sheet to be fitted in the MS. frame welded / sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing. complete all as specified and as directed. |
| 15 | S&F for butt hinges , extruded aluminium alloy with galvanised mild steel hinge pin anodised of100 mm size and fixed type C-21complete all as specified |
| 16 | S&F for Extruded aluminium alloy handle of 150 mm size fabricated type, anodised complete all as specified.. |
| 17 | S&F for aluminium anodised barrel tower bolt of 150mm of extruded section complete all as specified. |
| 18 | S&F Aluminium alloy, anodised, sliding door bolt 250mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed |
| 19 | S&F galvanised wire cloth, 0.48mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanised staples complete all as specified and directed |
| 20 | S&F 4.8 mm thick tinted glass of selected quality in square not exceeding 0.5 sqm in each pane, fixed to aluminum frame with and including suitable rubber beading complete all as specified and directed |
| 21 | Demolition of cement concrete of any description and in any position (unreinforced) in ground floors and paving not exceeding 15 cm thick (below or above GL) complete all as specified and directed. |
| 22 | Demolition of cement concrete of any description and in any position reinforced concrete (re-inforcement cut to facilitate demolition) including disposal of unserviceable of mateial complete all as specified and directed. Note:Demolition material throughout MOD Land rate include above item |
| 23 | Dismantiling of stone slabs and tiles (Kota stone etc.) of any discription or any thickness in floors, aprons, skirting, dado, pcc tiles at roof etc. laid bedded and pointed in any mortar complete all as specified and directed. |
| 24 | Dismantling floor, hearth or wall tiling of any description and in any position including cement mortar bedding (but not backing) complete all as specified and directed. |
| 25 | M&L for hardcore of broken stone or boulders gauge n exc 63 mm, deposited, spread and levelled in layers n exc 15 cm thick, watered and rammed to a true surface. |
| 26 | M&L 18-20 mm thick pre-polished Granite slab, machine cut, for floors/ shelves, cooking platforms, window cills, steps, jambs and pillar top laid over & including 20mm thick screed in CM 1:4 and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone complete all as specified & directed. |
| 27 | M&L for rounding, chamfer, splays or arris and smooth finishing at the edges of stone as in steps, cooking platform and other similar locations complete all as specified and directed. |
| 28 | M&L 75mm thick PCC (1:3:6) Type C2 using 40mm graded stone agg as in plinth protection surface even and smooth without using extra cement including oint sealing compound of grade A complete all as specified and as diected by engineer in charge. |
| 29 | M&L 25 mm thick cement concrete (1:2:4) type B-0 (12.5 mm graded stone aggregate) as in floors,finish rough to receive th\e floor finishes etc |
| 30 | M&L for machine cut Kota stone slab 18 mm to 22 mm thick , as in flooring , laid over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing , over and including screed bed or bedding layer of mortar 20 mm thick in cement mortar (1:6 ) complete all as specified and directed. |
| 31 | M&L for machine cut kota stone slab 18 mm -22 mm thick as in riser / steps, skirting, dado,cills and pillars laid and jointed with grey cement slurry mixed with pigment to match with the shade of the slab including rubbing and polishing over and including 10 mm thick backing coat in CM (1:4) complete all as specified and directed. |
| 32 | M&L for vitrified ,coloured and printed tiles of 8 to 10 mm thick (Square / Rectangular ) polished area of each tiles not exceeding 0.36 Sqm as in flooring over and including 15 mm thick cement screed in (1:6 ) CM set and jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of tiles complete all as specified and directed. |
| 33 | M&L for vitrified ,coloured and printed tiles of width as directed and 8 to 9 mm thick as in skirting fixed over and including 10 mm thick backing coat in (1:4 ) CM set and jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of tiles complete all as specified and directed. |
| 34 | M&L marble stone strip as in border etc in kota stone flooring machine cut bedded jointed and pointed with grey cement slurry including cutting and polishing to mirror finish complete all as specified and directed.Note :- Marble strips of 75 mm wide & 10 to 15 mm thick shall be used. |
| 35 | S&F 5mm thick hollow wall panelling plain colour PVC sheet in strips & channel feathered at the edges for fixing on Solid PVC Wall Lining,Insulated PVC Wall Lining, and Solid PVC Partitions inclusive of solvent cement and fixing at site including disconnecting and refixing of electric light board complete all as specified and as directed. |
| 36 | M&L for digital glazed ceramic tiles, coloured tiles 300mm x 600 mm x 7mm thick on vertical faces ie. as in skirting/dado etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles fix over and including 10 mm thick backing coat in cement mortar (1:3) complete all as specified and directed. |
| 37 | M&L non-skid coloured ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.06 Sqm but not exceeding 0.11 sqm in floors set and jointed in neat cement slurry and pointed in white or coloured cement to match coiour/shade with & including 15mm thick screed bed layer in CM 1:6 complete all as specified |
| 38 | Taking down cement or cement lime plaster on brick or stone walls etc. including racking out joints hacking for key scrubbing down with water etc.complete. |
| 39 | M&L for 15 mm thick rendering in cement mortar (1:4) on brick / concrete/ stone surfaces finished even and fair without using extra cement complete all as specified and as directed. Note : Water proofing compound shall be measured and paid separately under appropriate item of BOQ as \\"supply only \\" |
| 40 | M&L for 15 mm thick rendering in cement mortar (1:6) on brick or concrete surfaces finished even and smooth without using extra cement complete all as specified and as directed. |
| 41 | Supply only Liquid water proofing compound complete. |
| 42 | M&L for preparation of the newly plastered surfaces of wall & applying 3 coats of white wash on wall surfaces complete all as specified and directed. |
| 43 | M&L for new plaster surfaces of walls applying two coats of exterior emulsion acyrlic weather proof antifungal paint over a coat of exterior grade primer (including putty ) upto 08 meter height of the bldg, complete all as specified and directed. (Make -Asian Apex, Berger) |
| 44 | M & L for two coat of oil bound emulsion paint over a coat of Birla wall care putty 2 mm thick on plastered surfaces on wall incl. preparation of surfaces complete all as specified and directed. . |
| 45 | M&L Complete removal of existing treatment (internal and external suraces) on walls by scrapping with steel wire brush or any other means including one coat of wall care putty on wall and applying two coat of oil emulsion complete all as specified and directed by Engineer -in-Charge. |
| 46 | M&L preparation of surfaces of walls by scrapping/sand preparing / rubbing and finally washing with watering and applying two coats of exterior emulsion acyrlic weather proof antifungal paint over a coat of exterior grade primer upto 08 meter height of the bldg, complete all as specified and directed. (Make -Asian Apex, Berger) |
| 47 | M&L precast re-inforced Cement Concrete 1:2:4 type B1 (using 20mm graded stone agg) as in cover slabs for man holes, Shelves etc set in cement mortar 1:6 including necessary form work complete all as specified and directed. |
| 48 | Demolition of brick work /stone work built in cement mortar including all quoins, arches, pillars etc complete all as specified and as directed. |
| 49 | Removing excavated material nexc 50m and depositing where directed at a level nexc 1.5Km above the starting point with soil complete. |
| 50 | M&L Brickwork with fly ash Modular bricks in cement mortar, straight or curved on plan exc 6m mean radius, built in built cement mortar 1:4 in complete all as specified and as directed |
| 51 | M&L for brick work with sub class 'Fly ash brick, in cement mortar 1:4, straight or curved on plan to any radius in half brick thick wall complete all as specified & directed. |
| 52 | M&L Brick work with sub class B bricks straight or curved on plan exc. 6m mean radius built in cement mortar (1:6). (EXCEPT BRICS ONLY) |
| 53 | M&L for preparation surfaces for building Nos and applying one coat of synthetic enamel paint and writing letters or figures (Block, Roman, Italic or Indian) of n exc 10cm height, width of letter shall not be less than 15mm, including stops, commas, lines, brackets and making outer boarder with approved tint of synthetic enamel thick paint complete all as specified and as directed. |
| 54 | Dismantling of wall and ceiling boards fibre pulp insulation etc or insulation boards/slabs/blankets any thickness including cover fillets, complete all as specified and directed. |
| 55 | S&F False ceiling 4 mm thick HPSC pre-prime non asbestos fibre cement building board ( size 600mm x 600 mm/ 595 mm x595 mm ) decorative finish fixed with clips and screw including powder coated galvanised MS grid frame work false ceiling of ( Main Tee size 32mmx20mmx0.45mm cross tee 24mmx24mmx0.30mm and wall angle19x19x0.30 mm ) and with slot for fixing including suspended with1.25 mm dia. GI wire hangers fixed with steel dash through fasteners from purline of the roof complete all as specified and as directed. |
| 56 | Dismantling of AC (corrugated / semi-corrugated) sheets in roof covering including any type of ridges complete all as specified and as directed. |
| 57 | S&F Pre painted galvalum sheet 0.50 mm thick having aluminum zinc coating 150 gsm/ sqm corrugated steel sheet any colour having tensile strength of 550 Mpa as in Roof covering /cladding to wall fixed with self tapping screws complete all as directed by Engineer -in -charge. |
| 58 | S&F Pre painted galvalum sheet 0.50 mm thick having aluminum zinc coating 150 gsm/ sqm plain steel sheet any colour having tensile strength of 550 Mpa as in Roof covering /cladding (ridge) to wall fixed with self tapping screws complete all as directed . |
| 59 | M&L Hand rails, half round or other stock section or core for wooden hand rail straight portion , drilled and counter sunk for balusters running bars, for doors, balusters, nosing to steps including embedding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing post including cutting tops to shape as directed, drilling holes, notching for wire , etc.; flat iron fillets ( for securing wire mesh etc. including all necessary drilling , bolting or rivetting , etc., and similar work conforming to Fe 290 Gde E 165 with and including applying two coats of synthetic enamel paint over a coat of primer alround before fixing in position complete all as specified and directed |
| 60 | Dismantling timber scantling , framed /un framed work of 40 sq. cm and over in section in any position complete as directed. |
| 61 | Dismantling of wrought iron or mild steel work of any description not other wise provided for complete all as specified and as directed. |
| 62 | S&F rolled section as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors fixed with angle cleats or other connecting plates confirming to Fe-290 ( Gde E-165) complete all as specified and directed |
| 63 | S&F for framed work such as grills gratings, etc, with ends of bars shouldered and or riveted , or forged into spikes, framed guard bars , barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe 290,E-165 , complete all as specified and directed. |
| 64 | M&L for two coats of synthetic enamel paint over a coat of red oxide primer on new steel surfaces over 10 cm width or girth including preparation of new surfaces. |
| 65 | M&L two coat of synthetic enamel paint over coat of Red oxide primer over Old steel surfaces nexc 10 cm width or girth complete. |
| 66 | Cutting of cracks to V section in existing wall surface, cleaning out, wetting, grouting with cement and sand slurry 1:3 etc complete all as specified and directed. |
| 67 | M&L for reinforced cement concrete nominal mix type B1 (1:2:4) ( using 20 mm graded stone aggregate ) as in beams , cantilevers bressummers , lintel over 1.5 m span etc. complete all as specified and directed. |
| 68 | M&L for use and waste Formwork to sides & soffits of floor or roof beam rough finished surfaces of concrete complete all as specified and directed . |
| 69 | S&F mild steel bars 10 mm dia and over (TMT) cut to length bent to shape required including cracking,bending spirally for hooping ends and binding with and including mild steel wire not less than 0.90 mm dia quality of steel conforming to Fe-410-0 or Fe-410-S. |
| 70 | S&F TMT bars 6 to 8 mm dia cut to length bent to shape required including cracking,bending spirally for hooping ends and binding with and including mild steel wire not less than 0.90 mm dia quality of steel conforming to Fe-410-0 or Fe-410-S. |
| 71 | Dismantling boarding any description fixed with nails in any position (including cup board shutter/shelve upto 25mm thick) complete. |
| 72 | S&F in repair 18/19mm thick WPC board, prelaminated both face with decorative choice laminations one side and other side balancing white, fixed with screws to timber frame work including beading on cutting /exposed edges, polishing for cupboard shutter including following hardware:-Make : Rajshri /Black Cobra |
| 73 | S&F for aluminium anodised barrel tower bolts of extruded section of 100mm size, complete all as specified and directed. |
| 74 | S&F for continuous (piano) hinges mild steel bright finish or electro galvanised width of width of flaps nexc 30 mm (when open), complete all as specified and directed. |
| 75 | S&F for extruded aluminium alloy handle of 100 mm size fabricated type, anodised.complete all as specified . |
| 76 | S&F for Haps and staple safety type Aluminium anodised with MS hinge pin including bolt to hinge pin of 100 mm size sixed with screw complete all as specified . |
| 77 | S&F for magnate catcher of metal body and striking plate heavy duty includind fixed with screw, complete all as specified and directed. |
| 78 | Taking up or down steel tubing and connetion including cleaning for refixing or removing to store of 20mm bore of pipe, complete all as specified and directed. |
| 79 | Taking up or down steel tubing and connection including cleaning for refixing or removing to store of 25mm bore of pipe, complete all as specified and directed. |
| 80 | supply and laying 20 mm dia .of bore CPVC pipe SDR11 and Plain CPVC SDR11 fittings (ISI ) marked ,concealed or fixed to wall or laid in floors complete all as specified and as directed |
| 81 | supply and laying 25 mm dia .of bore CPVC pipe SDR11 and Plain CPVC SDR11 fittings (ISI ) marked ,concealed or fixed to wall or laid in floors complete all as specified and as directed |
| 82 | S&F 25 mm bore SS Pipe curtain rods including SS brackets & SS decorative dome, suitable for door/widows curtain with fancy type SS decorative dooms with ss brackets fitted to each end and fixed to wall with wooden battens incl. removal of existing rod and making good complete all as specified and directed. |
| 83 | S&F for as in repair viterous china wash down water closet pan (pedestal pattern) white excluding fixing bolts,flushing cistern and flush pipe including connection to drain and to flushing pipe syphonage pipe etc and mild steel chromium plated or aluminised hinges device & on CP Jet complete all as specified and directed. |
| 84 | S&F in reapir plastic water closet seat covered white coloured closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging devise complete all as specified and directed. |
| 85 | S&F for in repairs of vitreous china wash basin, white, oval type, size 550 x 400mm Including waste coupling ,waste pipe and labour for fixing pillar tap ,pvc connection but including cutting for and pinning in ends of and including brackets complete all as specified and directed. . Note : Pillar tap and PVC connection will be measured paid separetly. |
| 86 | S&F for in repair PVC valveless syphonic action type flushing cistern low level white with inlet ball valve,float end handle handle including bracket complete of capacity 10 litres, complete all as specified and directed. |
| 87 | M&L vitreous china squatting pan, orissa pattern sise 580x440mm white with integral foot rest (excluding flushing cistern) including vitreous china ‘P’ or ‘S’ traps connection to trap and to flushing pipe to complete fixed in repairs and making good to floor complete. |
| 88 | S&F for in repairs15mm,pillar taps ISI Mark Fancy type long body chromium plated,cast copper alloy, with brass ceramic disc spindle and capston heads,scewed down high pressure, with or without lettered 'hot' or Cold' with long srewed shanks and flynuts, srewed for iron pipe complete all as specified ..MAKE : Neptune series of Prayag or similar in PARRYWARE/CERA /JAQUAR/HINDWARE |
| 89 | S&F for in repairs 15mm angle cock ISI Mark chromium plated,cast copper alloy, with brass ceramic disc spindle and capston heads,scewed down high pressure, with or without lettered 'hot' or Cold' with long srewed shanks and flynuts, srewed for iron pipe fixed and complete all as specified ..MAKE : Neptune series of Prayag or similar in PARRYWARE/CERA /JAQUAR/HINDWARE |
| 90 | S&F for 15mm ,bib tap ISI Mark Fancy type long body chromium plated,cast copper alloy, with brass ceramic disc spindle and capston heads,scewed down high pressure, with or without lettered 'hot' or Cold' with long srewed shanks and flynuts, srewed for iron pipe fixed in repair and complete all as specified .MAKE : Neptune series of Prayag or similar in PARRYWARE/CERA /JAQUAR/HINDWARE |
| 91 | S&F for in repairs vitreous china urinals, Half stall type ,white with grating and union for discharge pipe complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement complete all as specified and directed. |
| 92 | S&F for in repairs Soap dish of CP fixed with pvc rawal plugs and screw, complete all as specified and directed. |
| 93 | S&F for in repair CP tubular towel rail D type 20mm dia and 60cm long complete all as specified and directed. |
| 94 | S&F for peg set of six S.S. fixed to wall with PVC plugs and screw, complete all as specified and directed. |
| 95 | Supply only 15mm dia PVC connection with PTMT nuts of length 450 mm, complete all as specified and directed. |
| 96 | S&F in repair Health faucet with 1.00 metre tube ( Branded tube ) including flexible pipe and brass chromium plated nuts completed all as specfied and directed Make Prayag cat No BEA-40S or equivenet in other make |
| 97 | S&F for in repairs Looking mirror 5 mm to 6 mm thick with fixing brackets ,screws, pvc rawal plugs etc. complete all as specified and directed |
| 98 | S&f corner glass shelf 300mm ( with ABS Bracket ) complete all as specified and directed. |
| 99 | S&F for in repairs mild steel Chromium plated grating 100 mm dia, fixed in repair, complete all as specified and directed. |
| 100 | S & F in repair Rotational moulded poly-ethylene multilayer water storage tanks (cylinderical vertical with closed top) 1000 litres capacity, triplr layer in construction white in colour hoisted and fixed in position complete all as specified and directed. |
| 101 | S&F for 20mm ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/ 20 m m - 210 gms / 25mm-455gms/ 40mm - 690 gms) complete all as specified and directed. |
| 102 | S&F for in repair gun metal globe / gate valve with iron wheel head screwed both ends for iron pipe of 20mm bore, complete all as specified and directed. |
| 103 | Taking down eaves gutters and rain water pipes (any size 75mm to 110mm of any pattern) ,of any description and in any position, including all fittings , heads, shoes, bends, swan necks, etc., (measured overall as fixed along the centre line over fittings and accessories)complete all as specified. |
| 104 | S&F for 110mm dia PVC(SWR) pipes single socketed, in any length with rubber ring joints,fixed to walls complete all specified. |
| 105 | S&F for 75 mm dia PVC(SWR) pipes single socketed, in any length with rubber ring joints,fixed to walls. complete all as specified . |
| 106 | S&F for 75 mm dia PVC(SWR) pipes single socketed, in any length with rubber ring joints,laid in trenches or in floors complete all as specified . |
| 107 | S&F for 110mm dia PVC(SWR)pipes bends any radious \ complete all as specified and directed. |
| 108 | S&F for 75 mm dia PVC(SWR)pipes bends any radious. complete, complete all as specified and directed. |
| 109 | S&F for 110mm dia PVC(SWR)pipes junction,single (single T/Y ) equal or unequal any radious.with acces door, complete all as specified and directed. |
| 110 | S&F for 110mm dia PVC(SWR) vent cowl, complete all as specified and directed. |
| 111 | M&L for 75 mm dia of out let PVC (SWR) floor trap plain with CP grating including jointing with solvent cement as in repair complete all specified. |
| 112 | M&L for PVC (SWR) gully trap 125 /100 plain with grating incl. jointing with solvent cement as in repair, complete all as specified and directed. |
| 113 | S& F GI wire netting 0.90mm dia and 12mm mesh lathing to wood or metal studding, joists, etc. in walls, ceilings, stanchions, beams, etc. including all laps, cutting and waste complete all as specified and directed. |
| 114 | Surface excavation n.exc. 30 cm deep and av. 15 cm deep and getting out in any type of soil complete |
| 115 | M&L for PCC Type D2 (1:4:8) using 40mm graded stone agg as in foundation filling mass concrete, complete all as specified and directed. |
| 116 | Material and labour for providing and laying 80mm thick factory made ISI MARK GLOSSY FINISH chamfered edge cement concrete paver block of M-30 grade with aproved colour , design & Pattern as in foothpath, parks, lawns, drive ways or light traffic arking etc. of required strenght, thickness & size / shape, made by table vibrating method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding / laying of interlocking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed. |
| 117 | M&L for cement concrete ( 1:2:4) type B-1 (20mm graded agrregate) in lintels upto 1.5m clear span, cills, stes, seimic and other similar bands, plinth course, string course, lacing cours, arapets and railings upto 60cm in height, coping, kneelers, apex stones, bed plates, kerbs, water througs and the like including wheathering slightly rounded or chamfered angle and throating complete all as specified and directed. |
| 118 | Material and labour for providing and laying 60 mm thick factory made ISI MARK chamfered edge cement concrete paver block of M-35 grade with aproved colour, design & attern as in foothpath, parks, lawns, drive ways or light traffic arking etc. of required strenght, thickness & size / shape, made by table vibrating method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding / laying of interlocking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra cement complete all as specified and directed. |
| 119 | M&L for 50mm thick cement concrete type B2 1:2:4 (40mm graded aggregate) as in floor/hardstanding finished even ans smooth without using extra cement complete all as specified and directed by the Engr-in-Charge. |
| 120 | M&L for vitrified paver color tiles 40 cmx40cmx9 to 10 mm thick, moulded set jointed and pointed in neat cement slurry with grey cement and pigment, in floors, over and including 15 mm thick screed bed or bedding layer of cement mortar (1:6) complete all as specified and directed. |
| 121 | Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. and removing materials to store for taking credit and making good disturbed surfaces of walls, floors, etc.complete all as specified and directed. |
| 122 | M&L for concealed Point wiring with 1.5 Sqmm FRLSH insulated, unsheathed, multistranded, 1100 Volts grade copper conductor cable single core conforming to IS:694 along with one run of 1.5 Sqmm FRLSH insulated copper conductor cable green in colour for continuous earthing drawn through and including medium grade rigid PVC conduit conforming to IS:9537 (Pt-III) and its all accessories/junction boxes/ inspection covers etc of suitable size but not less than 20mm concealed in wall/ floor etc including provision of pressed steel terminal box of thickness not less than 18 SWG, with earth dolly of suitable size concealed in wall and covered with 3 mm thick phenolic laminated hylam sheet fixed with brass /GI screws for mounting switches, sockets, fan regulator, etc. complete all as specified and directed by Engineer-in-Charge for the following points:- |
| 123 | One light point controlled by one switch |
| 124 | One Exhaust fan point controlled by one switch. |
| 125 | One ceiling fan controlled by one switch and one regulator |
| 126 | One Bell point controlled by one switch |
| 127 | One 6A socket point controlled by one switch on independent board |
| 128 | One 6A socket point controlled by one switch on same board |
| 129 | All as per srl item no. 2 here-in-before but with 4 sq mm FRLSH copper wire with 4 Sqmm FRLSH copper earth wire for one 16 Amp socket point controlled by one 16 Amp switch on independent board. |
| 130 | S&F, Switch piano type, single pole, one way, 6 amps, 240 volts, complete all as specified and directed. |
| 131 | S&F, Switch piano type, single pole, one way, 16 amps, 240 volts, complete all as specified and directed. |
| 132 | S&F, Socket, 6 pin, 6/16 Amp, multipurpose 240 volts, complete all as specified and directed. |
| 133 | S&F, Socket, two-in-one, 5 pin, 6 Amp, universal type, 240 volts, complete all as specified and directed. |
| 134 | S&F, angle holder, metal cased, bakelite body, 240 volts, complete all as specified and directed. |
| 135 | S&F Bell push switch, single pole, one way, 6 Amps, 240 volts, complete all as specified and directed. |
| 136 | S&F electric bell of DINGDONG type, 240 volts, single pole and making all necessary connections, complete all as specified and directed. |
| 137 | Supply and fix electronic fan regulator in 5 steps, 240V,120 watt 50Hz complete all as specified and directed. |
| 138 | S&F, Ceiling rose, three terminals, bakelite body, 240 volts, complete all as specified and directed. |
| 139 | S & F 9/10 W White LED retrofit lamp suitable for B-22 holder base with polycarbonate diffuser and aluminium heat sink. |
| 140 | M&L for concealed Circuit/submain wiring alongwith earth wire 2 runs x 6 sqmm + 1 run x 6 sqmm with FRLSH insulated copper conductor, single core cable drawn through and including medium grade rigid PVC conduit conforming to IS:9537 (Pt-III) and its all accessories/junction boxes/ inspection covers etc of suitable size but not less than 20mm concealed in wall/ floor etc complete all as specified and directed by Engineer-in-Charge. Note: Three runs of copper cable and one run of PVC conduit shall be measured as one unit length |
| 141 | All as per srl item no. 13 here-in-before but 2 runs X 4 Sqmm + 1 run X 4 Sqmm. Note: Three runs of copper cable and one run of PVC conduit shall be measured as one unit length |
| 142 | All as per srl item no. 13 here-in-before but 2 runs X 4 Sqmm + 1 run X 4 Sqmm. Note: Three runs of copper cable and one run of PVC conduit shall be measured as one unit length |
