|
| 1 | Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. |
| 2 | Dismantling of ceramic, vitrified tiles carefully and scraping the plaster to making the surface clean for refixing the tiles including removing of malba complete in all respect and to the entire satisfaction of the Engineer in charge. |
| 3 | Providing and fixing false ceiling at all heights including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.L channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.L intermediate channel with connecting clips made out of 2.64 mm dia x 230 mmlong G.L wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer’s specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks) |
| 4 | Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed Vitrified tiles Matt/Antiskid finish of size Size of Tile 600 x 600 mm |
| 5 | Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand). Medium shade pigment using 50% white cement 50% Grey cement |
| 6 | Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete |
| 7 | Providing, applying and filling with cement based putty (Birla, JK or equivalent) to the required finish complete in all respect and to the entire satisfaction of Engineer in Charge. |
| 8 | Providing and laying vitrified floor tiles of size 600 x 600 mm double charge (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved brand & manufacturer, in all colours and shade. The tiles are to be fixed with 3mm grove using spacers. The tiles are to be laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm The grove are to be filled with cementitious grout mix with proportion of 0.90 kg grout and 0.10 kg of hardener for each kg of filling material. Double charge vitrified tile of size 600x600 mm |
| 9 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) of 1st quality with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, in skirting. The tiles are to be fixed with 3mm grove using spacers. The tiles are to be laid on 12mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm. The grove are to be filled with cementitous grout mix with proportion of 0.90kg grout and 0.10 kg of hardener for each lg of filling material. Double charge vitrified tile of size 600x600mm |
| 10 | Providing and fixing 8mm thick wooden laminated floor class of use 31/23 having wear resistance level of AC-3 as per EN-13329 with a direct pressure laminate surface including profile, treated with aluminium side, flooring of approved colour and shade complete in all respects and to the entire satisfaction of the Engineer in charge. |
| 11 | Providing and fixing brick tile cladding of size 9\\"x3\\" having 1/2\\" thickness at all heights with chamfered edge F.P.S (non modular) machine made brick tiles, laid in 12mm thick cement sand mortar 1:3 on RCC beams, lintels and fascias etc. in required shade and pattern complete in all respects as per entire satisfaction of Engineer-in-charge. |
| 12 | Providing and fixing 2nd class teak wood (kiln seasoned) chowkhat 4 1/2\\" x 2 1/4\\"including cost of corner straps, iron hold fasts, hinges, screws,nails, fevicol etc. and spirit polish of chowkhats. Rate includes the cost of dismantling of all damaged chowkhats and making good the damage to walls plaster and floors as required including, disposal of rubbish to the dumping ground the rate further includes the cost of two coats Spirit polish complete in all respect and to the entire satisfaction of Engineer-in-Charge |
| 13 | Providing and fixing 35mm thick phenol bounded factory manufactured solid flush door shutter ISI marked with both side 4mm teak ply in the existing chowkhat. The rate includes the cost of all necessary stainless steel fittings and french spirit polish on teak ply complete in all respect to the entire satisfaction of Engineer-in-charge. |
| 14 | Providing and Fixing 35mm thick 2nd class teak wood (kiln seasoned) wire gauge door shutter consisting of 100mm x 35 mm style and top rail 150 mm x 35 mm lock rail 200mm x 35 mm bottom rail wire mesh 22 x 12 mm gauge fixed with 1/2” x 3/4” teak wood (kiln seasoned) beading, incluuding Stainless Steel fittings and french spirit polish, complete fixed in position and in all respect to the entire satisfaction of Engineer-in-Charge. |
| 15 | Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick |
| 16 | Providing and fixing 35mm thick 2nd class teak wood (kiln seasoned) glazed window shutters consisting of vertical and horizontal styles 75x35mm size with 4mm thick floated glass pane fixed with 1/2\\"x3/4\\" teak wood (kiln seasoned) beading. The rate further includes the cost of 3\\" butt hinges, S.S. Tower bolts 4\\", S.S. handles 2 nos. I hook and two coats of Spirit Polish after preparation of surface (special quality) complete in all respect to the entire satisfaction of Engineer-in-charge. |
| 17 | Providing and fixing 35mm thick second class teak wood (kiln seasoned) wire gauge window shutters consisting of vertical and horizontal styles 75x35mm size with wire mesh 22 x 12mm gauge fixed with 1/2\\" x 3/4\\" teak wood beading. The rate further includes the cost of 3\\" butt hinges stainless steel tower bolts 4\\", 4\\" stainless steel handle 2nos, stay 1no, screws, nails etc. I-hook, french spirit polishing two or more coats complete in all respect to the entire satisfaction of Engineer-in-charge. |
| 18 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete |
| 19 | Providing and fixing 2'-0\\" deep cupboard /cabinet consisting of 19mm thick commercial board and 6mm thick ply on back side, 1 mm thick mica on the exposed surface and making shelves in cabinet. The rate further includes the cost of lipping, piano hinges, cupboard lock, screws, nails, 2 nos. fancy s.s. handles, 2 nos. magnetic catchers, fevicol and painting two coats over one priming coat and preparation of surface on board and ply surface complete in position as per entire satisfaction of Engineer-in charge. |
| 20 | Providing and fixing wooden cabinet of 13½” deep and 2’-0\\" height with open able shutter at wall above 4’-9\\" height consisting of 19mm thick with commercial board (ISI marked) lipped with teak wood lipping of 19mm x 6mm on exposed edges include cost of nail, screws, auto hinges, synthetic adhesive etc. The front shutter and sides are to be furnished with 1mm thick ISI marked superior quality mica of approved shade and inner side of the cabinet with 0.8mm thick mica of approved shade fixed in position with help of wooden gutties at wall complete in al respect to the entire satisfaction of Engineer in charge. |
| 21 | Providing and fixing of kitchen cabinet below working shelves made out with 19mm thick commercial ISI marked plyboard and front portion of the cabinet furnished with 1mm thick superior quality sun mica of outer side and 0.8mm thick sun mica inner side of the cabinet for fixing the kitchen accessories and jack at bottom synthetic enamel paint over remaining portion. It is also include the cost of sprit polishing on the edge of the lipping cost of stainless steel handle, adhesive, nail, screws etc. complete fixed in position to the entire satisfaction of Engineer-in-Charge. |
| 22 | Providing and fixing heavy duty S.S. kitchen plate basket 17” x 20” x 8” accessories fixing in the existing cabinet with help of best quality telescopic channel. |
| 23 | Providing and fixing heavy duty S.S. kitchen grain trolley of size 21” x 20” accessories fixing in the existing cabinet with help of best quality telescopic channel. |
| 24 | Providing and fixing heavy duty S.S. kitchen corner basket 21\\" deep accessories fixing in the existing cabinet with help of best quality telescopic channel. |
| 25 | Providing and fixing heavy duty S.S. kitchen Basket of size 21” x 20” x 6” accessories fixing in the existing cabinet with help of best quality telescopic channel. |
| 26 | Providing and fixing heavy duty telescopic channel for drawers 18\\" to be fixed with necessary screws complete in all respects and to the entire satisfaction of the Engineer in charge. |
| 27 | Providing and fixing heavy duty S.S. kitchen masala pull out 6\\" accessories fixing in the existing cabinet with help of best quality telescopic channel. |
| 28 | Taking out existing CC interlocking paver blocks from footpath/ central verge, including removal of rubbish etc., disposal of unserviceable material to the dumping ground, for which payment shall be made separately and stacking of serviceable material within 50 metre lead as per direction of Engineer-in-Charge. |
| 29 | Providing and laying 60mm thick high density rubber moulded precast cement concrete paver block grey/colored/ polished/ designer (manufactured by vibro hydraulic pressure process) consisting of design mix of cement, sand and fine aggregate having designation M35 ISI marked including the cost of good quality colour and hardening agents, The paver should be complied with tensile strength and breaking load as per BIS 6717-1993 and shall be tested against resistance to bear as per IS 1237-1980 ( specification for cement concrete floor tiles). The paver should be laid over layer of 50mm average thick sand to the required slope and requirement complete in all respects and to the entire specification of Engineer in charge. |
| 30 | Providing and fixing 4mm thick plain glass panes with beading when required over existing chowkhat or fixed shutter or fixed portion or glazed shutter including the cost of nails, putty etc. complete in all respect to the entire satisfaction of Engineer-in-charge. |
| 31 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. with necessary screws to the existing wooden frame including coat of synthetic enamel paint over one coat of primer complete in all respects and to the entire satisfaction of the Engineer in charge. |
| 32 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1:4 (1 cement : 4 coarse sand) |
| 33 | Providing and fixing golden champ jaffery on compound wall with frame of golden champ section 2” x 1.3/8” as horizontal member and vertical members fixed with golden champ and strips 4”x 3/8” @ 6” c/c on both faces sides faces of jaffery. The top of jaffery is to be covered with another strip of 2 x 1.3/8”. The complete panel is to fixed over existing wall and M.S. angle with iron nuts and bolts etc. The complete jaffery is to be painted with special quality over one coat of primer complete in all respect to the entire satisfaction of Engineer-in-charge. |
| 34 | Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth upto 50 m and lift upto 1.5 m, as directed by Engineer-in- Charge: |
| 35 | Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. |
| 36 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:4:8 (1 Cement : 4 coarse sand (zone-Ill) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 37 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand) |
| 38 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.Cement mortar 1:4 (1 cement :4 coarse sand) |
| 39 | 12 mm cement plaster on rough side of single or half brick wall of mix:1:4 (1 cement: 4 coarse sand) |
| 40 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 41 | Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour. Two coats |
| 42 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : One or more coats on old work |
| 43 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). |
| 44 | Providing and laying PVC/PU self adhesive tactile tile (for vision impaired persons as per standards) of size 300x300 with approved make in all colours and shades in floors such as corridors, stair, ramp etc. complete as per direction of Engineer-in-charge. |
| 45 | Finishing walls with Acrylic Smooth exterior paint of required shade :Old work (Two or more coat applied @ 1.67 ltr/ 10 sqm) on existing cement paint surface |
| 46 | Centering and shuttering including strutting, propping etc. and removal of form for Shelves (Cast in situ) |
| 47 | Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers |
| 48 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). |
| 49 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 50 | Demolishing brick tile covering in terracing including stacking of serviceable material and disposal of unserviceable material within 50 metres lead |
| 51 | Demolishing mud phaska in terracing and disposal of material within 50 metres lead. |
| 52 | Grading roof for water proofing treatment with Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) |
| 53 | Laying brick tiles using existing dismantled tiles over mumty roofs, grouted with cement mortar 1:3 (1 cement: 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement, over 12 mm layer of cement mortar 1:3 (1 cement : 3 fine sand) and finished neat. The old tiles should be in perfect shape & without any breakage & cleaned complete in all respect and to the entire satisfaction of Engineer-in-charge. |
| 54 | Providing and laying brick tiles over mumty roofs, grouted with cement mortar 1:3 (1 cement : 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement, over 12 mm layer of cement mortar 1:3 (1 cement : 3 fine sand) and finished neat With common burnt clay F.P.S. (non modular) brick tiles of class designation 10 |
| 55 | Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : In 75x75 mm deep chase |
| 56 | Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. |
| 57 | Providing and laying in situ five course water proofing treatment with APP (Atactic Polypropylene) modified Polymeric memberane over roof consisting of first coat of bitumen primer @ 0.40 litre per sqm, 2nd & 4th courses of bonding material @ 1.20 kg/sqm, which shall consist of blown type bitumen of grade 85/25 conforming to IS : 702, 3rd layer of roofing membraneAPP modified Polymeric membrane 2.0 mm thick of 3.00 Kg/ sqm weight consisting of five layers prefabricated with centre core as 100 micron HMHDPE film sandwiched on both sides with polymeric mix and the polymeric mix is protected on both side with 20 micron HMHDPE film. 5th, the top most layer shall be finished with brick tiles of class designation 10 grouted with cement mortar 1:3 (1 cement : 3 fine sand) mixed with 2% integral water proofing compound by weight of cement over a 12 mm layer of cement mortar 1:3 (1 cement : 3 fine sand) and finished neat (item of laying brick tiles shall be paid for separately) |
| 58 | Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq. meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per directions of Engineer-In-Charge. With cement mortar 1:4 (1cement: 4 fine sand) |
| 59 | Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.In cement mortar |
| 60 | Providing and fixing IRC welded mesh 30mm x 30mm in M.S. angle frame of 30x30x3mm and M.S. flat 20x5mm on the inner side including cost of cutting welding, fixing the complete frame in the exisitng brick / RCC structure with 3\\" long 8 nos. fasteneres including painting two coats of synthetic enamel paint over one coat of metal primer complete in all respects and to the entire satisfaction of the Engineer in charge. |
| 61 | Providing and fixing roller blinds of approved make (D'Décor, Vista, Home Décor, Winshade or equivalent), shade and colour as approved by Engineer-in charge. The blinds shall be spring loaded resin operated media of polyster able limit rays allowing natural illumination. Spring loaded resin mounted part made up of MS zinc coated of thickness of 2mm molded in PVC. Mounting brackets must have provision cushioning to reduce noise during operation and must have provision of wall as well as ceiling installation. The idler pin made of zinc plated MS of 9mm outer diameter surrounded by bearing balls to support blinds at other end. This bidirectional blind shall be operational by assistance of polyster cord. This polyster cord should be moulded in side PVC beads of 4.5 mm outer dia. The blinds shall be operational without any hindeerance. The desk let assembly shall be flip-up type shall be made up of extension tube of 1.6+/- 0.02cm dia X 0.22+/-0.016 cm thick MSERW (As per approved sample to entire satisfaction of Engineer in charge.) |
| 62 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 63 | 15 mm cement plaster on rough side of single or half brick wall of mix:1:4 (1 cement: 4 coarse sand) |
| 64 | Providing and laying Polished granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 15 to 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement 4 coarse sand) and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by th Engineer-in-Charge |
| 65 | Providing and laying Polished Granite stone 15 to 18 mm in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) annd ointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete |
| 66 | Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved. Please Enable Macros to View BoQ information |
