Tender For Construction Of Convention Center Building In Anupuram Township., Chengalpattu-Tamil Nadu

TDR : 55729205

Tender Notice
BOQ

18 Days Left

Chengalpattu , Tamil Nadu

Tender Brief : Tender For Construction Of Convention Center Building In Anupuram Township.

Document Fees
Refer document

EMD
₹ 4106000.0 /-

Tender Value
₹ 31.06 Crore /-

Submission Date
18-06-2026

Competition Type
Indian

Bidding Type
Tender

Need a Business Loan? Apply Now !


1	Part - A : Civil Works
2	Part - B : Electrical Works, Internal Intercom Telephone System and Network system & CCTV
3	Part - C : AC Works, Fire Alarm System and Fire Fighting System
4	Earthwork excavation by mechanical means (Hydraulic excavator)/manual means for foundations, trenches, etc., not exceeding 1.5m in width or 10 sqm on plan in hard gravelly soil and other types of soil including bailing of water, if necessary, dressing of sides, levelling and ramming the bottom of trenches, refilling the sides of foundation as required with selected excavated earth and depositing/disposing the surplus earth (Disposed soil to be levelled by breaking clods, if any and neatly dressed) with lift upto 1.5m and within a lead of 200 metres, etc., all complete as per specifications and as directed.
5	All kinds of soil upto 1.50mtr depth
6	All kinds of soil exceeding 1.50 mtr depth but not exceeding 3.00 mtr depth
7	Earthwork in open Excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30 cm in depth, 1.5m in width as well as 10 sqm on plan) in all types of soil, mixture of gravel, disintegrated rock, hard stiff clay, soft rock, hard rock including bailing of water, if necessary, dressing of sides, shoring, benching, levelling and ramming the bottom surfaces, with lift as given below and disposal of excavated earth within a lead of 200 metres, etc., all complete as per specifications and as directed by the Engineer-in-Charge.
8	All kinds of soil - Upto 1.5 mtr depth from AGL
9	All kinds of soil exceeding 1.50 mtr depth but not exceeding 3.00 mtr depth
10	All kinds of soil - Exceeding 3.00 mtr depth but not exceeding 4.50 mtr depth
11	Ordinary/ soft rock exceeding 1.50 mtr. depth but not exceeding 3.0 mtr. depth
12	Ordinary/ soft rock exceeding 3.0 mtr. depth but not exceeding 4.50 mtr. depth
13	Excavating trenches of required width by mechanical means (Hydraulic excavator)/ manual means for pipes, cables etc., for depth upto 1.5m in all kinds of soil including excavation for sockets, dressing of sides, ramming of bottoms, getting out the excavated soil and then refilling the soil as required in layers not exceeding 200mm in depth, consolidating each deposited layer by ramming, watering etc., and disposing of surplus excavated soil as directed within a lead of 200m, (Disposed soil to be levelled by breaking clods, if any and neatly dressed) etc., all complete as per specification.
14	Providing a system for dewatering and drainage of water from site to main drain so as to retain the excavated formation dry for the duration required including all equipment's, consumables, site protection, etc., all complete as per specifications and as directed by Engineer- in-Charge.
15	Filling available selected excavated earth (excluding rock) in trenches, plinth, sides of foundation etc., in layer not exceeding 200 mm in depth including consolidating each deposited layer by ramming and watering, lead upto 200 metres and lift upto 1.5m etc., all complete as per specification.
16	Supplying and Filling with selected Earth brought from outside sources for basement, foundation sides, etc., including conveyance by lorry load , filling in layers of not more than 200mm depth, each layer shall be well consolidated including watering and dressing sides, levelling, dressing the top surface to required level, etc., all complete as per standard specifications and as directed by Engineer-in-charge.
17	Providing Pre-Construction Anti-termite Treatment using Chlorpyriphos E.C 20% with 1 % concentration or other approved chemical as detailed below including cost of chemicals, labour and all other incidental charges for entire ground floor area of building and injecting termicide emulsion to the soil in contact with the foundation along the perimeter of both internal and external walls, etc., all as per IS: 6313 (Part-2). 1) Top surface of consolidated earth within plinth walls shall be treated with chemical emulsion @ 5 Ltr/Sq.m of the surface before the sand bed or sub-grade is laid. 2) Treatment along the external perimeter and internal perimeter at junction of the wall and the floor of the building shall be treated with chemical emulsion @ 7.5 Ltr/Sq.m, to facilitate this holes shall be provided @ 150mm apart upto GL for inner side and upto 300mm below GL for external perimeter. 3) The entire treatment shall be done as per the specifications and instructions of the termicide Manufacturer and as directed by the Department. 4) The treatment should be done by an agency specialized in the job having sufficient knowledge of anti termite treatment. 5) Five years guarantee from the date of completion of maintenance period shall be given by the contractor in the prescribed format of the department for the above anti-termite treatment work.
18	Disposal of surplus excavated earth / Debris by collecting, loading, transporting by mechanical means and unloading them at places as shown by the Department within a lead specified below and levelling, etc., all complete as per specifications and as directed by the Engineer-in-Charge.Note: 1) The rates in respect of this item are applicable for the NET Quantities arrived at after making deductions for voids @ 20% in respect of soil and @ 50% in respect of rock from the corresponding stack / truck measurements.2) The earth shall be dumped well inside the dumping yard and not over approach pathway road.
19	Exceeding 1 Km but not exceeding 2 Kms
20	Construction of Granular sub-base (Grading-I) by providing close grade Material, mixing in a mechanical mix plant at OMC, carriage of mixed Material to work site, spreading in uniform layers with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per clause 401 of MORT&H specifications for road and bridge works( 5th Revision) and as directed by the Engineer - in - charge.
21	Providing and laying in position of plain cement concrete using hard granite broken stone in foundations, trenches etc. including mechanical mixing, ramming, compaction, leveling, curing, dewatering, if any including the cost of formwork etc., all complete as per specifications.
22	1 : 3 : 6 (1 cement : 3 sand : 6 graded stone aggregate 20mm nominal size)
23	1 : 2 : 4 (1 cement : 2 sand : 4 graded stone aggregate 25mm nominal size)
24	Providing, erecting, placing in position and removing Formwork for all insitu concrete works at all lifts and all shapes such as circular works, chamfers, splays, etc., using Steel / Plywood shuttering including centering, scaffolding, strutting, propping with necessary bracing in all areas, fixing of EPs, cutting holes and fixing pipe sleeves, applying of approved form oil over surface in contact with concrete, de-shuttering after specified curing period, etc., all complete as per drawings and specifications.[Note : Measurement for the formwork shall be the area of forms in contact with concrete surfaces. Stop boards for construction joints will not be measured separately for payment. Centering and shuttering where exceeding 3.5m height in one floor shall be measured and paid for separately.]
25	For Plain Surfaces at all levels
26	For Curved Surfaces at all levels
27	Providing and casting insitu Reinforced Cement Concrete of the following grades of design mix by Weigh batching using machine crushed hard broken granite stone of nominal size 20mm including cost of admixtures in recommended proportion wherever required, mechanical mixing, transporting, placing at all lifts, vibrating, consolidation, curing, finishing smooth all exposed faces, for all insitu concrete items, etc., as per drawings and specifications.Note :1) The rate quoted shall be exclusive of reinforcement and formwork which will be paid for separately under relevant items.2) The rate of concrete shall include the cost of admixture in recommended proportions as per IS 9103 as per direction of Engineer-in-charge.3) Cement proportion for Concrete Mix shall be on the basis of weigh batching only as per design mix.4) The cost towards any upward / downward variation required to obtain the specified strength over the minimum cement content will be paid for or deducted at the rate specified in Schedule 'F'.
28	M 30 Grade Concrete (The Cement content considered is 370 Kg per Cu.m) - Upto FFL
29	M 30 Grade Concrete (The Cement content considered is 370 Kg per cu.m) - above FFL and upto floor V
30	Providing, cutting, bending, placing and binding Steel reinforcement using TMT bars of Fe-500D grade in all reinforced cement concrete works including cutting, bending, fixing, tieing in position with 1.6 mm dia soft drawn annealed binding wire, cost of cover blocks in C.M 1:2, etc., complete as per specifications and drawings. Important Note: The required quantity of steel reinforcement as mentioned in the schedule should be procured by the contractor only of SAIL, Rashtriya Ispat Nigam Limited (VIZAG), TATA Steel & JINDAL from authorised dealers which shall conform to IS: 1786 (Latest Edition).
31	Manufacturing, supplying, hoisting and fixing in position at all lifts, precast units of various patterns and sizes for precast plain solid units, slabs, exhaust fan moulds etc., in reinforced cement concrete of 1:1.5:3, using 20mm and below machine crushed graded stone aggregate and crushed stone sand including weigh batching, mechanical mixing, casting, vibrating, finishing of exposed faces, curing, necessary formwork & moulds, transporting and placing at all lifts, preparation of connections, grouting with cement mortar/cement grout wherever needed excluding steel reinforcement complete all as per drawing, specification and as directed by Engineer-in-Charge.
32	Providing and constructing brick masonry at all lifts in cement mortar 1:5 using well cured flyash bricks of class 5 (non-modular) made up of using Flyash + Sand + Lime + additives (Gypsum/Cement) with waterproofing chemicals and accelerators confirming to IS-12894 or latest edition including suitable scaffolding, raking out joints, continues curing for specified period, etc., all complete as per specifications and drawings.
33	Upto FFL
34	Above FFL
35	Providing and constructing 110mm thick brick work for partition walls at al lifts in cement mortar 1:4 using well cured flyash bricks of class 5 (non-modular) made up of using Flyash + Sand + Lime + additives (Gypsum/Cement) with waterproofing chemicals and accelerators confirming to IS-12894 or latest edition including supplying and providing 2 Nos. of 6/8mm MS rod at every third layer, suitable scaffolding, raking out joints, continues curing for specified period, etc., all complete as per specifications and drawings.
36	Supplying, fabricating and fixing Steel work welded in built up sections and framed work at all lifts comprising Chequered plates, MS angles, other structural steel sections, etc., of TATA or SAIL or approved equivalent make including cutting, welding, bending to shape, painting exposed faces with two coats of anti-corrosive paint of approved colour over a coat of red oxide zinc chromate primer / zinc phosphate primer, embedding with Cement concrete, if necessary, etc., all complete as per specifications and drawings.[Note: The rate shall be inclusive of lifting arrangements if any required to hoist and concrete embedment's for fixing the steel works.]
37	In gratings, frames, guard bar, ladders, railings, brackets, gates and similar works
38	Providing, supplying, cutting, bending to shape, welding, fabricating, hoisting, placing and fixing in position structural steel members like trusses, purlins etc. with curved profile of members using MS hollow / circular / square / rectangular tubular sectionsconforming to relevant IS standard of TATA or SAIL or approved equivalent make including cutting, welding, bending to required shape for curved profile, hoisting, fixing in position at all lifts, embedding with cement concrete, painting the exposed faces with 2 coats of metal coat PU finish paint of make MRF or other approved make over one coat of epoxy zinc phosphate primer with thinner 1110 Ep for epoxy primer and thinner for finish for metal coat paint as per manufacturer instructions, etc., all complete as per specifications and drawings.(Note: Lifting device arrangements if any required also arranged by the contractor at his own cost.)
39	Supplying, fabricating and fixing Structural Steel work in built up sections for gate, handrailing, trusses and framed work for catwalk at all lifts comprising square / rectangular / Tubular hollow sections conforming to relevant IS standard of TATA or SAIL or approved equivalent make including cutting, welding, bending to required shape for curved profile, hoisting, fixing in position at all lifts, embedding with cement concrete, painting the exposed faces with 2 coats of metal coat PU finish paint of make MRF or other approved make over one coat of epoxy zinc phosphate primer with thinner 1110 Ep for epoxy primer and thinner for finish for metal coat paint as per manufacturer instructions, etc., all complete as per specifications and drawings.[Note: The rate shall be inclusive of lifting arrangements if any required to hoist, concrete embedment's and foundation bolts for fixing the steel works.]
40	Supplying, fabricating and fixing of EPs, Structural Steel work and pipe sleeves etc., at all lifts comprising MS angles, MS plates, tees flats, rounds, squares, other structural steel sections, pipe sleeves and pipes of various sizes, IS channels, IS beams, square rods, etc., of TATA or SAIL or approved equivalent make including cutting, welding, bending to shape, painting exposed faces with two coats of anti-corrosive paint of approved colour over a coat of red oxide zinc chromate primer / zinc phosphate primer, embedding with Cement concrete, etc. complete all as per specifications and drawings.Note: The rate shall be inclusive of lifting arrangements if any required to hoist and concrete embedment's for fixing the steel works.
41	Providing and fixing anodized aluminium plain plates /chequered plates for catwalks, embedded parts, trench covers, connection plates, etc., including anodized coating, cutting, hoisting, aligning, lifting and fixing in position, etc., all complete as per drawings and specification and as directed by the Engineer-in-charge.Note: The rate shall be inclusive of lifting arrangements required for fixing at all lift/levels.
42	Providing and fixing of colour coated double layer insulated roofing system for roof and cladding comprising top sheet of 0.5mm BMT of 470mm with 73mm high rib standing seam panel, sub grits, 50mm PUF insulation and bottom sheet of 0.5mm BMT of 1015mm with 28mm high rib including colour coating of 40micron, fixing of roofing system over purlin with vapour barrier using fasteners/ clips as per drawing, specifications and as directed by Engineer-in-Charge(Note: Plan area of roof sheet will be measured for payment and rate shall be inclusive of roof sheet overlapping. Preferred make Tata BlueScope Steel (Fortiss + Trimdek) or other approved make.)
43	Supplying, fabricating bending and fixing the position of AISI 304 grade stainless steel section for hand railing/hanger rods made of Hollow tubes, channels, plates, etc., of required size including butt / mitre welding, grinding, buffing, polishing, making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size on the top of the floor or the side of waist slab with suitable arrangement, drilling holes in floor/walls embedding/ grouting with suitable grouting materials, etc., all complete as per drawing and specification and as directed by Engineer-In-Charge.Note:- 1. The stainless steel tubular pipe/ section shall conform to ASTM A554/A312.2. All welding joint shall conform to V groove joint and joint shall be ground finish.3. There shall not be any spatter or imperfection on the pipe and the pipe surface shall be ground and smooth.4. External surface of SS pipe shall be buffed to mirror finish. 5. The rate shall be inclusive of providing ball joiners, flush joiners, base plate/flanges, cover plate, end caps epoxy glue, round face/square face glass connecters for fixing etched colour glass if any of required size with gaskets including curved railings where ever required cost of screws, weld etc.,6. The entire pattern of stainless steel hand railing work/pattern including fixing of etched glass, if any in the hand rail shall be got approval by Engineer in charge/Architect before execution.7. Only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc., for payment purpose.
44	Providing and fixing in FRP Ladder of 450mm width using Isophthalic Polyester Resin with, FR & UV made with 50mm nominal size square tube of 6mm thickness for vertical and 32mm nominal size fluted rung of 4mm thickness for horizantal member fixed @ 300mm spacing at all elevations inculding all fittings, transporting, scaffolding, fixing at all levels with wallbrackets using SS fasteners/ anchor bolts, etc., all complete as per specifications and as directed by the Engineer-in-Charge. Note: Rate Inculsive of plates, support, anchor bolt or Hilti system for installation of FRP ladder on the wall. Preferred Make shall be Indurotech or other approved make.
45	Providing and fixing 6mm thick fibre glass reinforced plastic (FRP) gutter of size 300x400mm fabricated using two coats of Isophthalic grade UV stabilized gel top coating followed by reinforcement of chopped strand mat and woven roving duly impregnated with unsaturated polyester isophthalic resin with extra reinforcement of MS strip of size 25x3mm at a distance of 1000mm c/c starting from one end of the gutter to be embedded with the gutter at all elevations complete all as per specification and as directed by the Engineer-in-charge.
46	Supplying, cutting to suitable size and shape and installation of 10 mm thick (ISO FR Resin reinforced with fibre glass - Woven Rovings- unidirectional rovings) Hot pressed SMC (Sheet Moulded Compound) Chequered plate on the existing RCC trench, Electrically insulated, withstand dielectric strength as high as 12KV/mm and insulation property makes it absolutely free from electric shocks suitable for out door use, in accordance with UL 746C can withstand static loading upto 1500 kg /sq.m, Density 1.70 to 1.90 gram/cc, Tensile Strength 650 to 750 kg/Sq.cm, Flexural Strength 1250 to 1400 kg/Sq.cm of make\\"Induratech/Devi Polymers/ Sintex \\" or equivalent including tight fixing in trench slots, cutting out opening if required, all required accessories & providing and provision of handle if required and as specified by manufacturer and as per specification and instructed by Engineer-in-charge.
47	Supplying and fixing in position 75mmx50mm size Wood Polymer Composite (WPC) solid door frame confirmed to IS:2380 latest having density of minimum 850 Kg/Cum, screw withdrawal strength of 2000 N at face and 1600 N at edge, water absorption less than 1%, Class A fire resistance and tensile strength greater than 12 MPa including fixing required hardware fittings, required screws, etc., all complete as per specifications and as directed by Engineer-In-Charge.
48	Supplying and fixing in position single leaf/double leaves of 28mm thick non decorative type factory made Wood Polymer Composite (WPC) solid door shutters confirmed to IS:2380 latest having density of minimum 650 Kg/Cum, screw withdrawal strength of 1500N at face and 1000N at edge, water absorption less than 1%, Class A fire resistance and tensile strength greater than 12 MPa including fixing required hardware fittings, fixing door using required screws, including providing recessions for hinges, finishing all edges with mixture of PVC powder & solvent for smooth finish, The door shutter shall be fixed with the following hardware fittings: - a) 4 Nos. of 75 mm long stainless steel butt hinges of GARG brand bearing ISI mark with suitable stainless steel screws. b) Two numbers of 125mm long anodised of make aluminium D handle Classic/Crown or approved equivalent as per IS - 208 bearing ISI mark with suitable CP screws.c) Two numbers of 150mm long stainless steel baby latch type/cranked type tower bolt with suitable CP screws. d) One number of 50mm long solid PVC door buffer with 75mm long CP screws.
49	Providing and fixing Vertical blinds of Vista Levelor or Marvel approved equivalent make with vanes of 100mm width made of non woven polyster fabric which are suspended from the stilt travellers by self aligning vanes hooly of effective optimized system, vanes shall be coupled together by means of bead chain pivotaly attached by closing to each side of each weight including the cost of blinds, fixing in slim aluminium head railing, runners, spacers, control units, other incidental charges, etc., all complete as per specification and as directed by Engineer. [Note :- Sample shall be got approved by the Engineer before making bulk order.]
50	Supplying and fixing of Translucent film over glass complete all as per drawing, specification and as directed by the Engineer-in-Charge.Note: The work shall be executed with skilled applicator as per manufacturer specifications and prefererd make shall be 3M or other approved equivalent make
51	Supplying, Manufacturing and Fixing Second class Teakwood frames and architraves for frames of doors, windows, clerestory windows, cupboards, and other frames made out of 50mm thick and below of approved second class teakwood of required sizes fixed including cutting, planking, jointing, making necessary rebate / grooves for fixing door shutter, fixing in masonry with required nos. of 40x5mm flat iron MS holdfasts 200mm long and embedding in cement concrete 1:3:6 or fixed in concrete with necessary screws / fasteners as directed for various sizes of structural openings including applying anti-termite chemical over the surface in contact with masonry / concrete, etc., all complete as per specifications and drawings.[Note: Rate shall be inclusive of providing required holdfasts, embedded in cement concrete, applying chemical and fixing.]
52	Supplying and fixing in position single leaf/double leaves of the following sizes of ISI marked non decorative type factory made flush door shutters having solid hardwood block board core with commercial facing on both sides, internal teakwood lipping (Internal lipping shall have a total depth of not less than 25mm) using second class teak wood on all four sides, phenol bonded, hot pressed, conforming to IS: 2202 latest edition, of various sizes with necessary test certificate as per drawings and specifications. Note: 1) Cost of Door frame shall be paid for separately under relevant item.2) The width of the frame including lipping shall not be less than 45mm and not more than 75mm.
53	Providing and fixing in position 8 mm thick cement bonded particle board panels of approved make, suitable for non-decorative applications on both sides, for use in partitions, aluminium composite panel (ACP) backing support, cupboard shutters, sliding shutters, etc., including cutting to required size, fixing within aluminium sections/flats, and finishing all joints with approved sealant, complete as per specifications and as directed by the Engineer-in-charge.(Note: Cost of aluminium sections, aluminium framework shall be paid separately under relevant items.)
54	Providing and fixing Aluminium Composite Panel (ACP) cladding of approved make, colour and shade of 4 mm thick (0.25 + 3.5 + 0.25 mm) for facia cladding, soffits, etc.,including fabrication and fixing with aluminium box section framework using aluminium profiles of minimum size 25 x 50 mm of 2.0 mm thick or other approved sections satisfying the structural design criteria, fixing at all heights / levels/elevation to the Masonry / RC walls with necessary brackets and anchor fasteners, scaffolding, cost of supplying and fixing of aluminium composite panel, weather sealant for Vertical & horizontal joints using approved sealents, fixing the aluminium frame work using aluminium cleat with spacing not exceeding 800 mm on both horizontal and vertical sides of each panel. all ACP fold at corners should be provided with corner 'L' cleat of 2mm thick and 50x50x3mm thk of bracket with welded on MS support / anchor fasteners. etc., all including necessary hardwares like nuts, bolts with washers screws , aluminium cleats, backer rods, DOW SIL 789/688 weather sealant. etc., all complete as per specifications, drawing and as directed by Engineer-in-ChargeNote : All aluminium section shall be anodized in approved colour to a minimum thickness of 20 microns or shall be PVDF coil / spray coated in approved colour and shade with metallic colours to a minimum thickness of 35 microns. Preferred make of ACP shall be Aludecor / Eurobond/Alstone or other approved make.
55	ACP Cladding wood finish for plain area
56	ACP Cladding wood finish for curved area
57	ACP Cladding metal finish for plain area
58	ACP Cladding metal finish for curved area
59	Providing and fixing of Aluminium perforated sheet of approved colour, shade and pattren/design of 1.2 mm thick including fabrication and fixing with aluminium box section framework using aluminium profiles of minimum size 25 x 50 mm of 2.0 mm thick or other approved sections satisfying the structural design criteria, cost of supplying and fixing of aluminium sheets along with cost of making perforation/design, weather sealant for Vertical & horizontal joints using approved sealents, fixing the aluminium frame work using aluminium cleat with spacing not exceeding 800 mm on both horizontal and vertical sides of each panel. all aluminium sheet fold at corners should be provided with corner 'L' cleat of 2mm thick and 50x50x3mm thk of bracket with welded on MS support / anchor fasteners. etc., all including necessary hardwares like nuts, bolts with washers screws , aluminium cleats, backer rods, DOW SIL 789/688 weather sealant. etc., all complete as per specifications, drawing and as directed by Engineer-in-ChargeNote : All aluminium section/ sheet shall be anodized in approved colour to a minimum thickness of 20 microns or shall be PVDF coil / spray coated in approved colour and shade with metallic colours to a minimum thickness of 35 microns.
60	Providing and fixing in position Aluminium partitions, doors, windows, ventilators, louvers, fixed glazing, sliding windows north light glazing, sliding shutter 'E' Channel, trellis, etc., using heavy duty standard anodized aluminium extruded sections, anodized aluminium sheets as per relevant IS code of \\"JINDAL\\" or approved equivalent make including pivots, approved door and window handles, door stopper, EPDM gasket, neoprene gasket lining, stainless steel screw, mastic filling, weather strips, washers, reinforcing the door shutters at top and bottom with MS rod threaded and fixed to vertical members, etc., as required and as per drawing etc., all complete at all heights and as directed by the Engineer in charge.Note:- 1. Payment shall be made on the basis of weight of aluminium members/section fabricated and actually installed in position without extra allowance for wastage no extra payment shall be made for non-aluminium consumable items like screws, gasket, weather strips PVC/Neoprene lining, sliding wheels for windows, in built tower bolt, reinforcing rods, etc., 2. Glazing, particle boards, Aluminium grills, mesh etc., will be paid separately under relevant items.3. All fittings except under Note-1 will be paid separately under relevant item and the fittings shall be of matching colour anodized aluminium sections. 4. The aluminium section shall be smooth, rust free, straight, mitered and jointed mechanically wherever required cleat angles at no extra cost.5. The aluminium section shall be anodized with \\"MATT FINISH\\" (15 micron thick) finishing and of approved shade/colour with the approval of Engineer-In-Charge.
61	Supply and fixing of Slim Glass partition using 12mm thick toughened glass with sleek 45mm aluminium profiles to the required size and shape to max height of 3mtr or as per drawing including the cost of making holes/ cutout on glass, fixing with anchor fasteners at floor/wall/ceiling as per architectural design, neoprene gasket, rubber beading, seals, sealent of approved grade, scaffolding, etc., all complete as per drawing/ manufacturer specification and as directed by Engineer-in-charge.Note: 1) The fixed glass panels shall be installed using Dormakaba Alterra Lite 45mm profiles at top, bottom, side profiles and end profiles for open glass edges. Glass-to-glass vertical joints shall be fixed using ‘H’ Junction profiles, including 90° L junction and T junction profiles wherever required. 2) All the glasses shall be 12mm thick toughened glass of make Saint Gobain or approved make.3). All aluminium profile shall be 2mm thick and shall be anodized with \\"MATT FINISH\\" (20 micron thick) finishing and of approved shade/colour with the approval of Engineer-In-Charge.4). The work shall be executed with highly skilled person and the preferred make shall be Saint Gobain for Glass and Dorma/ Dormakaba Alterra Lite system for fittings or other approved make
62	Designing, supplying, fabricating and installing in position of Semi-unitized Structural Glazing system with 32mm thick Double Glazed Units (DGU) fixed over main frame of vertical mullion and horizontals transom made out of specially designed extruded aluminium sections confirming to IS: 1285 with 15micron electro colour anodized in approved colour designed to withstand wind pressure up to 200 Kg/sq.m including fabrication of frame work, fixing at all heights / levels/elevation to the Masonry / RC walls with necessary brackets and anchor fasteners, fixing of Glass on aluminium subframe along with structural sealant with adhesive tape, all brackets shall be of Mild Steel with galvanized, necessary hardware like nuts, bolts with washers, screws, EPDM gaskets, aluminum cleats, double side cross linked polythene spacer adhesive tapes, backer rods etc., all complete as per specifications, drawing and as directed by Engineer-in-Charge. Note: 1) Cost of DGU of make Saint Gobain will be paid for separately under relevant item. 2) All aluminium section shall be anodized in approved colour to a minimum thickness of 15 microns or shall be PVDF coil / spray coated in approved colour and shade with metallic colours to a minimum thickness of 30 microns.3) Sealants shall be of DOW SIL 789/688 weather sealant and DOW SIL 795 Structural Sealant.4) Aluminium Extruded Sections shall be 6063 T5 or T6 alloy conforming to ASTM B 221 of make Jindal. Vertical Mullion of size 131x67x2mm thick, Horizontal Transom of size 81x67x2mm thick and End mullion - 131x38x2mm thick.5) This item is inclusive of all the required accessories for glazing work like superior quality gaskets, aluminium profiles, SS fixing bolts, SS anchors, SS screws & nuts, approved silicone sealants etc., scaffolding and other materials required for the complete work for fixing the glazing work.
63	Supplying and fixing of Double-glazing units (DGU) made up of toughened glasses of as detailed below including the cost of making holes/ cutout on glass, fixing with anchor fasteners at floor/wall/ceiling as per architectural design, seals, sealant of approved grade, scaffolding, etc., all complete as per drawing/ manufacturer specification and as directed by Engineer-in-charge.Note: 1) The DGU system shall have 8mm SKN 133 HS toughened glass on outer side + 16mm air gap with required aluminium mill finish spacer at the middle with 6mm Silicone bite + 8mm clear HS toughened glass on the interior side. The total thickness of DGU including the air gaps shall be 32mm.2) The cut outs/ holes if necessary shall be made at one corner or as per drawing for passing of copper pipes and wires from inside to outside.3) Colour, Texture and reflection of the coating shall be as per sample approved and 5 years manufacturer warranty for coating shall be submitted.4) Preferred make shall be Saint-Gobain or other approved make
64	Providing and fixing IS : 12817 marked stainless steel butt hinges (Heavy weight) of make GARG or approved equivalent make including fixing with suitable stainless steel screws, etc., complete.
65	125 x 65 x 2.50mm
66	Providing and fixing IS:208 marked Aluminium handles of size 125mm x 12mm dia. of make 'Classic or Crown' or approved equivalent make including anodized (anodic coating not less than grade AC 10 as per IS :1868) transparent or dyed to required colour or shade, fixing with necessary SS screws etc., all complete as per specification.
67	Providing and fixing anodised aluminium tower bolts of size 300x12mm (Barrel Type) ISI marked (IS: 204) of approved make (anodic coating not less than grade AC 10 as per IS:1868) transparent or dyed to required colour or shade with necessary screws etc. all as per specifications and as directed by the Engineer-in-Charge.
68	Providing and fixing anodised aluminium tower bolts of size 250x12mm (Barrel Type) ISI marked (IS: 204) of approved make (anodic coating not less than grade AC 10 as per IS:1868) transparent or dyed to required colour or shade with necessary screws etc. all as per specifications and as directed by the Engineer-in-Charge.
69	Providing and fixing Stainless steel Roller wheels of approved quality and make for aluminium sliding door shutters including fixing as directed by Engineer-In-Charge
70	Providing and fixing in position universal Hydraulic door closer bearing ISI mark of EVERITE/GODREJ or approved equivalent make as per IS:3564 (Type-B No.2) including fixing as per specifications.
71	Providing and fixing Swing type heavy quality top PIVOT for suspending aluminium door shutters of single or double leaf all as directed by the Engineer-in-Charge.
72	Providing and fixing Swing type heavy quality bottom PIVOT for suspending aluminium door shutters of single or double leaf all as directed by the Engineer-in-Charge.
73	Supplying and fixing in position of Stainless steel Aldrop (for Fire rated / Steel door) of size 20mm dia x 300mm Long of 'STI or approved equivalent' make and type bearing ISI mark with IS suitable screws/nuts and bolts with necessary tools and accessories including removing the existing damaged fixtures /parts and labour charges etc. at all elevations complete all as per specification and as directed by Engineer-in-Charge.
74	Providing and fixing double action hydraulic floor spring of \\"HARDWYN\\" or \\"GODREJ\\" or approved equivalent make with ISI mark, pivoting and all other arrangements including cost of cutting floor, SS cover plates with brass pivots & other necessary accessories required for the work to facilitate smooth operation of the door shutter etc., all complete as directed by the Engineer-in-charge.
75	Providing and fixing 6 Lever Brass Mortice Lock with brass handle „Godrej‟ or other approved equivalent make suitable for flush door with a pair of keys and pair of brass handles, complete all as per specification and drawings.
76	Providing and fixing Granite stone in Flooring with 16-18mm thick one side Leather finished granite stone slab of approved shade, colour, size and texture laid over 20mm (average) thick base in cement mortar 1 : 4 (1 cement : 4 coarse sand) including laying, chamfering, providing grooves where ever required, pointing the joints with approved grouting materials, curing, cleaning, polishing, etc., all completed as per drawings and specification.Note: The Granite stones shall be got approved by the Engineer before making bulk order. The rates for steps shall be inclusive of providing three Nos. of 4mm grooves @ 25mm interval on all the treads from the nosing edge.
77	Ruby red/Pitch black for Steps riser and treads using single piece of length upto 2mtr.
78	Providing and fixing Granite stone in Flooring with 16-18mm thick one side mirror polished granite stone slab of approved shade, colour, size and texture laid over 20mm (average) thick base in cement mortar 1 : 4 (1 cement : 4 coarse sand) including laying, chamfering, providing grooves where ever required, pointing the joints with approved grouting materials, curing, cleaning, polishing, etc., all completed as per drawings and specification.Note: The Granite stones shall be got approved by the Engineer before making bulk order. The rates for steps shall be inclusive of providing three Nos. of 4mm grooves @ 25mm interval on all the treads from the nosing edge.
79	Providing Half Round Edge Moulding to 16-18mm thick marble / Granite or 20mm thick Kota stone counters, vanities, sills, etc. including machine polishing the edges to give high gloss finish etc., all complete as per specifications and as directed by Engineer - in – charge.
80	Granite work
81	Providing and laying 40mm thick cement concrete flooring with Hardcrete concrete hardener topping under a layer of 28 mm thick cement concrete 1:1:2 (1 Cement: 1 Coarse sand: 2 graded stone aggregate of 12.5mm nominal size) and top layer of 12.5mm thick Hardcrete concrete of 1:2 (1 Cement hardener mix : 2 Stone aggregate of 6mm nominal size) the cement hardener mix shall be of 2 litre per 50 Kg of cement Hardening compound of make Snowcem or approved equivalent make including applying cement slurry, ramming, finished to required level, curing, etc., all complete as per specification, manufacturer specification and as directed by Engineer-In-Charge.
82	Providing and laying Indian Patent Stone flooring 25mm thick with cement concrete of mix 1:2:4 (1 part cement : 2 parts coarse sand : 4 parts graded stone aggregate), using 20 mm and 10 mm size hard broken stone aggregates, finished with a floating coat of neat cement, including laying in panels, applying cement slurry, compacting, curing, rubbing the surface smooth, and finishing with a power trowel machine etc., all complete as per specifications and as directed by Engineer - in - charge.
83	Providing and fixing glass strips in joints of terrazzo / IPS flooring using 40/20mm wide & 4mm thick glass strips including grinding the top surface smooth to match with the floor, etc., complete as per specifications.
84	Providing cement plaster skirting in cement mortar 1:3 using crushed stone sand, 18mm thick finished with a floating coat of neat cement including curing, making uniform height, cleaning the surface neatly at the time of handing over the area all as per specifications and as directed by the Engineer.
85	Supplying and laying 8mm thick Teak wood Parquet Flooring and skirting of approved pattern and shape laid over 25mm thick base layer with teak wood of size 150x25 mm or 200x25mm with suitable adhesive including preparation of surface, cleaning, applying adhesive, fixing base layer, finishing with nonglassy lacquer coating, etc., all complete over the existing flooring/skirting and as directed by Engineer-in-charge.
86	Providing and laying first quality Jointless polished vitrified tiles slabs of size 1200mm x 1800mm and 15mm thickness with water absorption less than 0.08% as per Latest Indian standards and conforming to IS 15622 in all colours and shades in Glossy or Matt or satin finish (as required by Engineer-in-charge) laid over a bed of minimum 20mm thick bed of cement mortar 1:4 using crushed stone sand (in skirting, over 12mm thick bed of cement mortar 1:3 using crushed stone sand) including machine/hand cutting to required size & shape, grouting the joints with white cement mixed with coloring pigment to match colour of tile patterns, curing, cleaning the surface neatly at the time of handing over the area complete all as per drawings and specifications.Note:- 1) Sample and product shall be got approved from Engineer-in-Charge before making bulk order. Tiles shall be of Somany or Johnson or Kajaria or other equivalent approved manufacturer. 2) The work shall be carried out as per specifications with skilled manpower.
87	IProviding and laying first quality Jointless polished vertified tiles of size 600x1200mm with water absorptions less than 0.08% conforming to IS: 15622 for flooring and skirting in all colours, shades, and finishes (Glossy / Matt / Satin as directed by the Engineer-in-Charge) and approved designs and pattern including setting over base layer of 20mm thick in cement mortar 1:4, jointing with grey cement slurry @ 3.3 kg per sqm or by using tile adhesive of approved make, grouting the joints with epoxy based joint filling material or other equivalent jointing materials, curing, cleaning the surface with acid wash etc., all complete as per specification and as directed by Engineer in charge. Note:- 1) Sample and product shall be got approved from Engineer-in-Charge before making bulk order. Tiles shall be of Somany or Johnson or Kajaria or other equivalent approved manufacturer. 2) The work shall be carried out as per specifications with skilled manpower.
88	Grouting the joints of Vitrified tile flooring laid using spacer block having joints (3 - 5mm width) by using approved colour epoxy based tile grout of make Kerakoll (Fugalite® Eco) or other approved make including mixing the hardener and mix as specified, filling/ grouting using required tools, finishing, cleaning the residual traces of grout over the tile surface, finishing complete as per manufacturer specification and as directed by Engineer-In-Charge.[Note: Finished tile area will be measured for payment purpose]
89	Providing and Fixing Homogeneous PVC sheet, 2mm thick, conforming to IS:3462 latest edition in flooring and skirting (Polyfloor or approved equivalent make) in approved pattern, colour & shade on a smooth and damp proof base using rubber based adhesive of approved quality and manufacturer like Dunlop-S -758, or Fevicol SR 998, or approved equivalent including cleaning & preparation of surface, levelling small undulations with plaster of paris if required , rolling with light wooden roller weighing about 5 kg all complete all as per specification and as directed by the Engineer-in-Charge.Note: The sample tile shall be got approved by the Architect/Engineer before procurement.
90	Providing and laying first quality Jointless outdoor vitrified tiles of size 600x600mm with water absorptions less than 0.08% conforming to IS: 15622 of JOHNSON (Endura) or KAJARIA (Duratech) for flooring and skirting in all colours, shades, and finishes (Glossy / Matt / Satin as directed by the Engineer-in-Charge) of approved pattern and design including setting over base layer of 20mm thick in cement mortar 1:4, jointing with grey cement slurry @ 3.3 kg per sqm or by using tile adhesive of approved make, grouting the joints with epoxy based joint filling material or other equivalent jointing materials, curing, cleaning the surface with acid wash etc., all complete as per specification and as directed by Engineer in charge. (Note:- The sample shall be got approved by the Engineer-in-charge before making bulk order)
91	Providing and laying 1st quality Rectified (Jointless) Ceramic floor tiles (Matt or Anti-skid) of size 1200 x 600 mm or more confirming to IS : 15622 of KAJARIA (Approved concept of Digital Series) or SOMANY (Digital Series - Glasstra) or JOHNSON (Approved concept of Satin & Rustic / Glossy series) or other approved make in all colours, shades in Floors laid over 20 mm thick cement mortar 1 : 4 (1 Cement : 4 Coarse sand) jointing with grey cement slurry @ 3.3 kg per sqm or by using Cement based high polymer modified quick set tile adhesive (water based) or other approved tile adhesive including grouting the joints with white cement and matching pigments etc., all complete as per specification.
92	Providing and fixing 1st quality Rectified (Jointless) Glazed ceramic wall tiles of approved concept series confirming to IS 15622 of \\"KAJARIA/ SOMANY / JOHNSON\\" or other approved make in all colours, shades of following sizes in Skirting, Risers of steps and Dados laid over 12 mm thick bed of cement mortar 1 : 3 (1 Cement : 3 Coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm or by using Cement based high polymer modified quick set tile adhesive (water based) or other approved tile adhesive including providing Motiff tiles, pointing in white cement mixed with pigment of matching shade, curing, etc., all complete as per specifications and as directed by Engineer-in-Charge.
93	Wall tiles of 300x600 mm or more [KAJARIA (Digital Series) or JOHNSON (Satin &Rustic / Glossy series)]
94	Supplying and fixing of Rigid PVC nosing of approved quality and colour at the corners of Ceramic tiles dadooing including finishing all complete as directed and as per specifications.
95	Supplying and laying of machine made tufted loop pile carpet of make Unitex - Sonnet or other approved equivalent make having woven polypropylene primary backing carpet and pile weight of 750 GSM of approved colour / shade / design over the existing floor/skirting including providing base layer with 8mm thick expanded polyurethane foam, preparation of surface, cleaning, laying by applying approved synthetic resin adhesive, etc., all complete as per manufacturers specification and as directed by Engineer-in-charge.[Note: The sample of carpet and the foam shall be got approved by the Engineer in charge before making bulk order and the work shall be executed through skilled manpower as per manufacturer's specification.]
96	Fixing of auditorium chairs (push-back / tip-up type) in position including drilling holes in RCC floor, fixing the chairs with SS anchor fasteners, grouting with non-shrink grout/epoxy, aligning the setas in proper rows and levels as per the approved seating layout drawing, consumables, shifting chairs from departmental store, etc., all complete as directed by the Engineer-in-charge.Note:1) Chairs will be supplied by the Department at free of cost (Department supply).2) Payment will be made per number of chairs fixed.
97	Providing and fixing 1st quality Rectified (Jointless) Ceramic outdoor cladding tiles of size 300x600mm of approved concept series confirming to IS 15622 of \\"KAJARIA/ SOMANY / JOHNSON\\" or other approved make in all colours, shades of following sizes in Skirting, Risers of steps and Dados laid over 12 mm thick bed of cement mortar 1 : 3 (1 Cement : 3 Coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm or by using Cement based high polymer modified quick set tile adhesive (water based) or other approved tile adhesive including providing Motiff tiles, pointing in white cement mixed with pigment of matching shade, curing, etc., all complete as per specifications and as directed by Engineer-in-Charge. Note:- 1) Sample and product shall be got approved from Engineer-in-Charge before making bulk order. Tiles shall be of Somany or Johnson or Kajaria or other equivalent approved manufacturer. 2) The work shall be carried out as per specifications with skilled manpower.
98	Supplying and laying of one course of Vitrified Cool Roof tiles over roof slab / sloped surface of terrace and skirting using tiles of size 300x300mm and 10mm (±10%) thickness of make SOMANY (or) JOHNSON (or) PAVIT or approved equivalent make and conforming to IS: 15622 (Group B1a (or) Group B1b) approved colour with SRI (Solar Reflectance Index) > 78, Solar reflection > 0.70 & initial remittance >0.75 laid on 20mm thick bed on Cement mortar 1:4 mixed with integral water proofing admixture including removal of dead mortar from roof slab, cleaning the surface, exposing floor & wall function along parapet and column if any, sealing the floor & wall junction with water proofing mortar, laying screed concrete in CC 1:2:4 to form slope and haunch portion along parapet, if any required including laying tiles with required slope as per manufacturer specification, grouting the joints with approved tile grout, etc., all complete as per manufacturer Specification and as directed by Engineer-in-Charge. (Note: - Cost of screed concrete in CC 1:2:4 will be paid for separately under relevant item.)
99	Providing and applying SBR based bond coat of make MC Bauchemie (Naufufill-SBR) or FOSROC (Nitobond SBR) or FAB Chemical (Mixbond SBR) or Bostik (Boscocem 475) or other approved make including preparation of surfaces by scrubbing / cleaning the fungus / stains, cleaning with water, filling the cracks with approved crack filler and including cost of all materials, labour, tools and plants, curing, scaffolding at all lifts, etc., all complete as per specifications and as directed by Engineer-In-Charge. (Note: Mixing ratio of chemicals, consumption and application shall be as per manufacturer specifications.)
100	Supplying and fixing of Acoustical False Ceiling using 15mm thick factory finish magnesite-bonded pinewood microfibre core pigmented ceiling tile of size 595x595mm or approved size/ selected colours and pattern having density not less than 600Kgs/m3, weight 9kg/m2 with noise reduction coefficient (NRC) upto 0.75 at all height of approved make and laid over grid system including fixing over grid of approved GI strut system for linear as well as curvilinear portion for all levels and all heights, providing bulk heads/ co light design and change levels as per drawings, providing suitable opening for mounting of lighting fixtures/ fittings and fire alarm system, provision for air-conditioning ducts, scaffolding, etc., all complete as per manufacturer specifications and as directed by Engineer-In-Charge including: -
101	a) The false ceiling system shall suspended on interlocking hot dipped GI - 'T' grid in true horizontal level and grid module size of 600x600mm. Grid system with 24mm 'T' with main T of 38mm (H) Cross 'T' of 32mm (H).b) Suspension system: Anchor C Clamp shall be securely fixed to truss purlin/channels. 8 mm GI rod cut to drop length shall be connected vertically from clamp to 1.5mm thick heavy duty GI slotted angle. Fix the Slotted angle to rod using lock nuts and washers ensuring vertical and horizontal alignment. The main T section of false ceiling grid system shall be suspended from the slotted angle using 6 mm J Bolt. The assembly will terminate with a 6 mm J-Bolt of required height securely connected to the main T-bar, ensuring proper alignment and stability of the ceiling systemc) The grid system shall be designed to accommadate the system track to run the service lanes for utilities and providing system track planks as per approved drawing.d) The panels shall conforming to following technical Parameters : Core Variants - Magnesite bonded pinewood fibre, Fire – Class 1&P, Acoustics – NRC upto 0.75, Thermal (W/mk) - 0.07, Climate (°C RH) – 50, 95, Light reflectance (%) – Low light, Green (VoC, RC %) – Low, 35e) The item includes cost of all material, labour, scaffolding, etc., and the work shall be executed through skilled manpower as per manufacturer's specification.f) The samples shall be got approved by the Engineer-In-Charge before making bulk order. Prefererd make - Anutone (Mat Ebony) or Armstrong or other approved equivalent make
102	Supplying and fixing of Acoustical False Ceiling using 15mm thick factory laminated texture finish magnesite-bonded pinewood fibre core ceiling tile of size 595x595mm or approved size/ selected colours and pattern having density not less than 400Kgs/m3, weight 6kg/m2 with noise reduction coefficient (NRC) upto 0.8 at all height of approved make and laid over grid system including fixing over grid of approved GI strut system for linear as well as curvilinear portion for all levels and all heights, providing bulk heads/ co light design and change levels as per drawings, providing suitable opening for mounting of lighting fixtures/ fittings and fire alarm system, provision for air-conditioning ducts, scaffolding, etc., all complete as per manufacturer specifications and as directed by Engineer-In-Charge including: -
103	a) The false ceiling system shall suspended on interlocking hot dipped GI - 'T' grid in true horizontal level and grid module size of 600x600mm. Grid system with 24mm 'T' with main T of 38mm (H) Cross 'T' of 32mm (H).b) Suspension system: Anchor C Clamp shall be securely fixed to truss purlin/channels. 8 mm GI rod cut to drop length shall be connected vertically from clamp to 1.5mm thick heavy duty GI slotted angle. Fix the Slotted angle to rod using lock nuts and washers ensuring vertical and horizontal alignment. The main T section of false ceiling grid system shall be suspended from the slotted angle using 6 mm J Bolt. The assembly will terminate with a 6 mm J-Bolt of required height securely connected to the main T-bar, ensuring proper alignment and stability of the ceiling systemc) The grid system shall be designed to accommadate the system track to run the service lanes for utilities and providing system track planks as per approved drawing.d) The panels shall conforming to following technical Parameters : Core Variants - Magnesite bonded pinewood fibre, Fire – Class 1&P, Acoustics – NRC upto 0.80, Thermal (W/mk) - 0.07, Climate (°C RH) – 50, 95, Light (%) – 85%, Green (VoC, RC %) – Low, 30e) The item includes cost of all material, labour, scaffolding, etc., and the work shall be executed through skilled manpower as per manufacturer's specification.f) The samples shall be got approved by the Engineer-In-Charge before making bulk order. Prefererd make - Anutone (Strand - Nubby) or Armstrong or other approved equivalent make
104	Providing & Fixing in position Suspended False ceiling system using 600x600mm Mineral fibre reinforced ceiling tile of approved colour/ pattern, tiles having 16/15mm thick, and approved surface design and edge profile (TEGULAR or equivalent) laid over grid system with 24mm wide T - section (Main T 38mm & cross T 28mm height) flanges having rotary stitching on the Main Runner suspended from the ceiling at required intervals including providing suitable opening for mounting of lighting fixtures & fittings, loud speakers, fire alarm system component and lighting system, also provision for Trap doors where ever required with necessary opening & locking arrangements for the accesses to air-conditioning Duct etc., all complete as per specification and as directed by EngineerNote : 1) The grid system shall be designed to accommodate the system track to run the service lanes for utilities and providing system track planks as per approved drawing.2) Suspension system: Anchor C Clamp shall be securely fixed to truss purlin/channels. 8 mm GI rod cut to drop length shall be connected vertically from clamp to 1.5mm thick heavy duty GI slotted angle. Fix the Slotted angle to rod using lock nuts and washers ensuring vertical and horizontal alignment. The main T section of false ceiling grid system shall be suspended from the slotted angle using 6 mm J Bolt. The assembly will terminate with a 6 mm J-Bolt of required height securely connected to the main T-bar, ensuring proper alignment and stability of the ceiling system3) Sample and product shall be got approved from Engineer-in-Charge before making bulk order. Tiles and grid system shall be of approved make. 4) The work shall be carried out as per specifications with manufacturer authorised specialized manpower.5) Preferred make - Daiken or Armstrong or Anutone or other approved make
105	Providing and fixing accoustical suspended false ceiling at all heights with integral densified 0.7mm thick Aluminium Clip-in false ceiling tiles of size 600x600 mm of approved texture, design and patterns as per specification, to be laid in true horizontal level suspended on interlocking exposed metal Grid of hot dipped galvanised iron section of 1 mm thick (galvanized @ 100 grams per sqm including both sides) comprising of main and cross C channel runners having silhouette face with white/ black reveal or suprafine face including installation of grid system using approved suspension system, laying the aluminium tiles, cost of all accessories required for installation of false ceiling system as per manufacturer specification, etc., all complete as per specifications and as directed by Engineer-in-Charge.Note:- 1) The tiles shall have GRIHA certified product as per specifications. 2) Sample and product shall be got approved from Engineer-in-Charge before making bulk order. Tiles and grid system shall be of approved manufacturer. 3) The work shall be carried out as per specifications with manufacturer authorised specialized manpower.4) The grid system shall be designed to accommadate the system track to run the service lanes for utilities and providing system track planks as per approved drawing.5) The item includes cost of all material, labour, scaffolding, etc., and the work shall be executed through skilled manpower as per manufacturer's specification.6) The samples shall be got approved by the Engineer-In-Charge before making bulk order. Prefererd make - Anutone or Armstrong or other approved equivalent make
106	Providing & Fixing of False ceiling with 12.5mm thick tapered edge gypsum moisture resistant board at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120gms/Sq.m. (both side inclusive) as per IS:277 and consisting of angle cleats of size 25mm wide, 1.6mm thick with flanges of 27mm and 37mm at 1200 c/c, one flange fixed to the ceiling with dash fasteners 12.5mm dia 50mm long with 6mm dia bolts other flange of cleat fixed to the angle hangers of 25x10x0.5mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I channels 45x15x0.9mm running at the rate of 1200mm c/c to which the ceiling section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26mm each having lips of 10.5mm at 450mm c/c shall be fixed in a direction perpendicular to GI intermediate channel with connecting clips made out of 2.64mm dia x 230mm long GI wire at every junction, including fixing perimeter channels 0.5mm thick 27mm high having flanges of 20mm and 30mm long the perimeter of ceiling fixed to wall/ partition with the help of rawl plugs at 450mm centre with 25mm long dry wall screws @ 230mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5x25mm at 230mm c/c including jointing and finishing to a flush finish of tapered and square edges of the boardwith recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150mm or both sides of joint and including the cost of painting one coat primer and two coats of emulsion paint of approved colour, including the cost of making openings for light fittings, grills, diffusers, cut-outs made with frame of perimeter channels suitably fixed, all complete as per drawings, specifications and directed by Engineer-in-charge.
107	Note : a) The grid system shall be designed to accommadate the system track to run the service lanes for utilities and providing system track planks as per approved drawing.b) The samples shall be got approved by the Engineer-In-Charge before making bulk order. Prefererd make - Anutone or Armstrong or other approved equivalent make
108	Providing & Fixing in position of Suspended Baffle type False ceiling system using 50mm thick magnesite-bonded pinewood fibre core (min 1mm wide) on both surfaces of approved size, colour/ pattern, and approved surface design and edge profile having density not less than 300Kgs/m3, with noise reduction coefficient (NRC) upto 0.9 at all height of approved make including fixing the suspension kit of approved type, dropped from the soffit slab to desired vertical height and horizontal spacing as per architectural design & drawing using suitable anchor bolts, Soffit Cleat, S-Hook, etc., suspending the individual baffles vertically with factory-fixed D-rings as per site condition, providing bulk heads/ co light design and change levels as per drawings, scaffolding, etc., all completed as per drawing, manufacturer specifications and as directed by Engineer-in-Charge.Note: a) The panels shall conforming to following technical Parameters : Core Variants - Magnesite bonded pinewood fibre core, Fire – Class 1&P, Acoustics – NRC up to 0.90, Thermal (W/mk) - 0.07, Climate (°C RH) – 50, 95, Green (VoC, RC %) – Low, 40b) The baffle system shall be designed to accommodate the system track to run the service lanes as per approved drawing.c) The item includes cost of all material, labour, scaffolding, etc., and the work shall be executed through skilled manpower as per manufacturer's specification. Suspended Baffles area will be measured for the purpose of payment.d) The samples shall be got approved by the Engineer-In-Charge before making bulk order. Preferred make – Anutone (Strand Wave) or Armstrong (Heradesign) or other approved equivalent make
109	Providing wall paneling using 8mm thick particle board over 4mm thick veneer with veneer facing fixing of approved colour, backing by 6mm thick commercial play and 50x25mm second class teakwood rough ground runner horizontal and vertical at around 600mm centre to centre including 2 coats of varnishing the veneer surface, varnish / painting the teak wood surface, varnish / paint mixed with antitermite chemical and necessary screws, nails, fevicol etc. all as per specification and as directed by the Engineer.
110	Providing and Fixing of Optra Acoustical Wall Panel with square edges made of fibre glass substrate 25mm thick, wrapped on the front side with an acoustically transparent fabric as per the approved shade (Husk, Copper, Sangria, Sesame, Coffee, Charcoal, Titanium, Flame, Peanut and Shell). The panel shall be classified for Fire Class A, as per ASTM E-84. The Acoustical Wall Panel shall be of sizes 600x600mm (Nominal) or 600x1200mm (Nominal) and shall achieve an NRC of 0.85 (Average value of Absorption Co-efficient readings taken at 250 Hz, 500 Hz, 1000 Hz and 2000 Hz) with 50mm airgap as per ASTM C423 to be fixed to wall on a framework of wooden battens and using Wall panel Impalers (supplied by the manufacturer) or by using construction adhesives (as per the instructions laid down by the manufacturer). The fibre glass substrate shall have a recycle content of 85%. INSTALLATION: Supply & installation of 50x50x3600 mm size of Aluminium frame work fixed in every 600mm in Vertical direction to supporting the Heradesign wall panels .An appropriate vapour barrier shall be applied/installed on the vertical surface before the installation to properly seal against entry of any moisture. Vapour barrier shall be installed as per Manufacturer’s recommendation. Install wooden batten grid of section 50x50mm or as approved by the Architect on the solid wall/partition to provide level and plumb surface. The Impalers shall be fixed to the battens using self-tapping screws, 3 nos. in case of 600x600mm and 4 nos. in case of 600x1200mm. Silica based construction adhesive to be dabbed on to the projecting elements (spikes) of the Impalers. Optra Wall Panels shall be pierced through the spikes of the Impalers ensuring the line and level of the panels are maintained. Note: The work shall be executed by Highly skilled authorised applicators as per manufacturer specifications and preferred make shall be Knauf Armstrong/Anutone or other approved make
111	Supplying and fixing of Melamine Laminate finish acoustical wall panelling using 16mm (±1mm) thick pinewood fiber boards of size 128/192mm (W) x 2400/2440mm (L) or other approved size/ selected colours with groove perforated slats having 2mm grove at 16mm c/c with27% open area or other approved pattern backlined with black acoustical fleece of Soundtex and tongue-groove edge for a seamless look having density not less than 800Kgs/m3, weight 9kg/m2 with noise reduction coefficient (NRC) upto 0.75 of approved make fixed over grid of approved GI strut system for linear as well as curvilinear portion for all levels and all heights as per manufacturer specifications and as directed by Engineer-In-Charge including: - a) Base grid work shall be installed using GI strut system including Cross channel having thickness 0.45mm, length 3600mm, knurled web 50mm, depth 25mm and equal flanges of 15mm fastened to wall and positioned horizontally and vertically in a regular manner at 600mm centers.
112	b) Aluminium core cross channel having thickness 0.5mm, length 2400mm, web 15mm & 27mm, depth 18mm and flanges of 7mm with suitable edge & centre brackets shall be fixed perpendicular to the strut with the help of fasteners at every 400mm centers.c) Panels of approved size shall be fixed perpendicular to aluminium core cross channel with suitable edge & centre brackets against wall to perfect fit including the panels shall be backlined with 25mm thick (weight @0.5Kg/m2) polyfiber acoustical infill of approved make fixed to the wall using approved adhesive (Stick 7 adhesive). Expansion joint of 3mm shall be provided at every 5mtr bothways d) Melamine Laminate finish acoustical wall panelling shall conforming to following technical Parameters : Core Variants - Pinewood E1 Fibreboard, Fire – Class 1 & P, Acoustics – NRC upto 0.75, Climate (°C RH) – 50, 70, Light reflectance – 75% (beech haya), Green (RC %) – 25, Hygiene (VoC, Clean room) – Low, Class 1, Strength, Load capacity (Kg) - Ball-Impacte) The item includes cost of all material, labour, scaffolding, etc., and the work shall be executed through skilled manpower as per manufacturer's specification.f) The samples shall be got approved by the Engineer-In-Charge before making bulk order. Preferred make shall be Anutone (Salon Slats Surco) or Aromstrong or other approved equivalent makes.
113	Supplying and fixing of acoustical wall panelling using 15mm thick factory made magnesite-bonded pinewood (min 1mm wide) fibre core board of size 595x595mm or approved size/ selected colours and pattern having density not less than 400Kgs/m3, weight 6kg/m2 with noise reduction coefficient (NRC) upto 0.8 at all height of approved make and laid over grid system including fixing over grid of approved GI strut system for linear as well as curvilinear portion for all levels and all heights, providing bulk heads/ co light design and change levels as per drawings, providing suitable opening for mounting of lighting fixtures/ fittings and fire alarm system, provision for air-conditioning ducts, scaffolding, etc., all complete as per manufacturer specifications and as directed by Engineer-In-Charge including: -
114	a) Base grid work shall be installed using GI strut system including Cross channel having thickness 0.45mm, length 3600mm, knurled web 50mm, depth 25mm and equal flanges of 15mm fastened to wall and positioned horizontally and vertically in a regular manner at 600mm centers.b) Aluminium core cross channel having thickness 0.5mm, length 2400mm, web 15mm & 27mm, depth 18mm and flanges of 7mm with suitable edge & centre brackets shall be fixed perpendicular to the strut with the help of fasteners at every 400mm centers.c) Panels of approved size shall be fixed perpendicular to aluminium core cross channel with suitable edge & centre brackets against wall to perfect fit including the panels shall be backlined with 50mm thick (weight @0.5Kg/m2) polyfiber acoustical infill of approved make fixed to the wall using approved adhesive (Stick 7 adhesive). Expansion joint of 3mm shall be provided at every 5mtr bothways d) The panels shall conforming to following technical Parameters : Core Variants - Magnesite bonded pinewood fibre, Fire – Class 1&P, Acoustics – NRC upto 0.80, Thermal (W/mk) - 0.07, Climate (°C RH) – 50, 95, Light (%) – 85%, Green (VoC, RC %) – Low, 30 e) The item includes cost of all material, labour, scaffolding, etc., and the work shall be executed through skilled manpower as per manufacturer's specification.f) The samples shall be got approved by the Engineer-In-Charge before making bulk order. Anutone (Strand) or Armstrong (Heradesign) or other approved equivalent make
115	Supplying and fixing of 94mm thickness Acoustical dry wall partition (Double Skin) using 12mm thick factory made magnesia core board of size 1200x2400mm (±2mm) or approved size/ selected colours and pattern having density not less than 1000Kgs/m3 at all height of approved make and laid over grid system including fixing over grid of approved GI strut system for linear as well as curvilinear portion in true horizontal & vertical for all levels and all heights, providing suitable opening for mounting of lighting fixtures/ fittings and fire alarm system, provision for air-conditioning ducts, scaffolding, etc., all complete as per manufacturer specifications and as directed by Engineer-In-Charge including the dry wall partition system shall be comprising of: -i) Frame Work: Floor & Head channels having thickness 0.55mm, length 3600mm, equal flanges of 32mm and web of 50mm shall be fixed to floor and ceiling with suitable fasteners at 300mm centres staggered. Noise and fire rated silicon sealant to be caulked along the perimeter of the partition frame before fixing channels. Then Stud channel having thickness 0.75mm, length 3600mm, unequal flanges of 34/36mm and web of 48mm shall be placed into the floor/head channel positioned vertically at 600mm centres. Extra reinforcement shall be provided at openings (doors, windows, etc.) & frame cavity.ii) Insulation: Polyfibre acoustical infill having thickness 50mm, width 600mm, density 1000gsm shall be fixed between the Studs and held in position by using chicken wire mesh/cross bracings/pasting on one side of the boards.iii) Board: The first layer of 12mm thick board shall be fixed on one side of the Stud framework in a staggered (ashlar or brick) pattern by using suitable self drilling drill tip fasteners at 300mm centres. Another layer of 12mm thick board shall be fixed over it in staggered pattern with suitable metal fasteners. Edges of the two layers of boards must not coincide. Same procedure to be followed on other side of the framework to give 2 layers on either side of framework. 4mm gap should be maintained between boards on all sides and the same shall be filled with approved sealants.
116	iv) Finishing: Installed partition system shall be sanded, smoothed, primered and roller finished by using water based emulsion paint of approved colour and pattern.v) The grid system shall be designed to accommadate the system for service lanes if any for utilities as per approved drawing.vi) The panels shall conforming to following technical Parameters : Core Variants – Magnesia, Fire – Class 1&P, Acoustics – STC upto 50, Thermal (W/mk) - 0.118, Climate (°C RH) – 50, 95, Green (VoC, RC %) – Low, 30, Strength - Antisagvii) The item includes cost of all material, labour, scaffolding, etc., and the work shall be executed through skilled manpower as per manufacturer's specification.Viii) The samples shall be got approved by the Engineer-In-Charge before making bulk order. Prefererd make - Anutone (Tufbloc) or Armstrong or other approved equivalent make
117	Supply, fabrication and fixing of double action single leaf glass door using 12 mm thick toughened glass with sleek 45 mm aluminium profiles, of required size and shape up to a maximum height of 3.0 m or as per approved drawings, including making necessary holes and cut-outs in the glass, fixing the assembly with suitable anchor fasteners at floor, wall and ceiling, providing suitable locking arrangement, stainless steel handle of approved design and matching diameter (min 25mm) up to 1.20 m length, neoprene gaskets, rubber beading, weather seals and approved grade sealant, including all accessories, scaffolding, alignment and finishing, complete in all respects as per architectural drawings, manufacturer’s specifications and as directed by the Engineer-in-Charge.Note: 1) The glass door shall be installed using Dormakaba Alterra Lite 45mm profiles allround the door at top, bottom and side profiles. Glass over panel shall be fixed using over panel profiles, including 90° L junction and T junction profiles wherever required. Floor Spring of BTS 75V with Hold open (as per EN 1154) and necessary seals to be provided all around the door frames.2) All the glasses shall be 12mm thick toughened glass of make Saint Gobain or approved make.3). The work shall be executed with highly skilled person and the preferred make shall be Saint Gobain for Glass and Dorma/ Dormakaba Alterra Lite system for fittings or other approved make
118	Supplying, fabricating and fixing of 45mm thick pressed Steel Flush Door of approved make having outer door frame of size 105x60mm (Single Rebate) and steel flush door as detailed below including fabricating the frame, door shutter, providing thermal barrier between sheet, filling the hollow portion of the door with honeycomb/Solid Polyurethene foam, providing vision panel of size 230x400mm with 5mm thick clear toughned glass of approved pattern, fixing the door with required hardware fitting of make Dorma or other approved make, fixing the door assembly with necessary hold fast / anchor fasteners as per site condition, filling the hollow of door frame and hold fast pocket with CC 1:2:4 using 12mm downgraded stone aggregate which will be paid for separately under relevant item., etc., all complete as per drawing, manufacturer specifications and as directed by the Engineer-in-Charge.Door Frame: - Outer door frame of size 105x60mm (Single Rebate) made from 1.2mm thick Galvanized steel sheet with Zinc coating not less than 120gm/Sqm and shall be finished with PU paint of approved colour over zinc rich epoxy primer. Provision for providing fixed glass of 300mm height at top over the door shutter shall be made as per drawing.Door Shutter:- Pressed Steel fully Flush double skin door shutter of thickness 45mm (+5mm) fabricated 0.8mm thick Galvanized steel sheet with Zinc coating not less than 120gm/Sqm with approved colour finish. Top and Lower skin joined by roll formed snap fitting groove on the style. Providing thermal barrier between sheet and filling the hollow portion of the door with solid Polyurethene foam of density not less than 40kg/m3. Providing vision panel of size 230x400mm with 5mm thick clear toughned glass of approved pattern as per drawing. The shutter shall be finished with PU paint of approved colour over zinc rich epoxy primer.
119	Hardware fittings: - Fixing the door with required hardware fitting such as 4 Nos of 100x75x3mm SS ball bearing hinges for each shutter, Mortice Lock with handle and key, SS push/pull bar handle for each shutter, Door stopper, PVC solid buffer, Door closer with standard arm, Door Co-ordinator/ Selector for double leaf door fixed over frame, concealed tower bolts for double leaf shutters, 1 No. of 150mm and 1 No. of 300mm barrel type premium SS tower bolt. All hardware fittings shall be of make ‘Dorma’ or other approved equivalent make over the wooden inserts placed inside the shutter.(Note:- The samples shall be got approved by the Engineer-In-Charge before making bulk order. STEELTECH or TATA (PRAVESH) or SIGNUM or other approved equivalent make)Single leaf door of size upto 1000mm width and 2400mm height without vision panel
120	Single leaf door of size upto 1000mm width and 2400mm height with bottom fix louvers panel of size 600x300mm
121	Double leaf door of size upto 1500mm width and 2400mm height without vision panel
122	Double leaf door of size upto 2000mm width and 2400mm height with vision panel
123	Double leaf door of size above 2000mm width and 2400mm height without vision panel (Patterned/Decorative)
124	Supplying, fitting, fixing in position of 5mm thickness Tinted glass of approved colour of \\"Saint Gobain\\" or approved equivalent make for doors, partition, windows, fixed glazing, louvers, etc., including fixing with putty, TW beading, Neoprene gasket, etc., all complete as per drawing and specifications.
125	Providing F3 finish over concrete surfaces in CM 1:1.5 (1 part cement :1.5 part fine sand) including wetting the surface, labours, curing, all materials, scaffolding, at all elevations all complete as per specifications and as directed by the Engineer-in-charge.
126	Plastering the ceiling / exposed surfaces of concrete with CM 1:3; 6mm thick to make the surface uniform, free from undulations and imperfections including hacking pock marking of surfaces with pointed tool, scaffolding, curing at all lifts etc., all complete as per specifications and as directed by Engineer-incharge. [Note: 6mm premium glass fibre of make Dugar & Co or Recron shall be mixed with Cement @ 60 gms of glass fibre per 50kgs of cement]
127	Plastering with Cement Mortar 1:5, 12mm thick for brickwork / Concrete on internal faces at all lifts including scaffolding, curing and forming grooves wherever necessary all complete as per specifications and as directed by the Engineer-incharge. [Note: 6mm premium glass fibre of make Dugar & Co or Recron shall be mixed with Cement @ 60 gms of glass fibre per 50kgs of cement]
128	Providing plastering to all external surfaces of brickwork and concrete at all elevations in cement mortar 1:5 using crushed stone sand, 20 mm thick applied in two coats, admixed with a cementitious waterproofing admixture of approved make at 400 g per bag of cement or an approved waterproofing chemical as per the manufacturer’s recommended dosage, including hacking of concrete surfaces with pointed tools, providing and removing scaffolding, finishing and curing the plastered surfaces, and forming grooves wherever required, all complete as per specifications and as directed by the Engineer-in-Charge.
129	Supplying and fixing in position of Alkali resistance Glass fibre mesh (4-5mm square aperture with 145 gsm) over the joints of RCC and Brick work with cement paste before plastering as directed by Engineer-in-charge.
130	Painting all internal faces of walls / ceiling plastered surfaces with One coat of Acrylic Emulsion paint of make Asian (Tractor) / Berger (Bison) or other approved equivalent make of approved shade over a coat of interior wall primer of make Asian (Professional) / Berger (BP Primer) or other approved equivalent make including preparation of surfaces, applying the primer coat, scaffolding, etc., all complete at all lifts as per specifications.
131	Painting all internal faces of walls / plastered surfaces with two coats of premium Acrylic Emulsion paint of make Asian (Apcolite) / Berger (Rangoli) or other approved equivalent make of approved shade over a coat of interior wall primer of make Asian (Professional) / Berger (BP Primer) or other approved equivalent make including preparation of surfaces, applying approved make wall care putty as per manufacturer specification, making surface smooth without porous, sanding the surface, applying the primer coat, scaffolding, etc., all complete at all lifts as per specifications.
132	Providing Painting over all exposed surfaces at all heights over rough cast plaster/plain plaster with Two Coats of premium exterior emulsion paint of make Asian (APEX - Dust proof exterior emulsion) / Berger (Anti dustt weather coat) or other approved equivalent make of approved shade over a coat of exterior wall primer of make Asian / Berger or other approved equivalent make including preparation of surfaces, curing, scaffolding etc., all complete as per specifications.
133	Painting over Plain Plaster at all lifts.
134	Painting External wall with Textured paint of approved pattern/ finish in three coats (One coat of Texture and two coats of External paint) over a coat of external primer of approved colour and texture of make \\"Berger (Walmasta) or Asian\\" (Apex Duracast) or approved equivalent make at external surface at all levels and height including preparing the base surface, sand the surface with sand paper, wash and scrub with coir/wire brush, attending to broken edges /corners or patches of plastered surface with cement grout, scaffolding, staging, painting one coat of Weather coat External primer of make Berger or other approved make, application of illusion texture using Berger- Walmasta exterior texture or other approved make, making approved patterns/designs using trowel/ roller, providing vertical/horizontal grooves if any required, painting the top surface with two coats of overcoat using weather coat exterior emulsion of make Berger (Weather coat smooth) or other approved make, cleaning the surface etc., all complete as per manufacturer's specification and as directed by Engineer-in-charge.
135	Providing and fixing in position of white glazed vitreous china ware ORISSAPAN water closet of size 580x440mm of approved make with \\"S\\" or \\"P\\" trap with all jointing materials including making holes in masonry, fixing the Orissapan, joining the pipe and trap with Lip Ring of approved make, reconstructing the same, encasing the pan and trap with brick jelly concrete 1:2:4 and back filling extra space with river sand/brick jelly concrete, all as per specifications and as directed by the Engineer-in-Charge. (Note:- The samples shall be got approved by the Engineer-In-Charge before making bulk order. Prefererd make - PARRYWARE/ HINDWARE or other approved equivalent make.)
136	Providing and fixing high level/Low level polymer DUAL flushing cistern of 3/6 litres capacity of approved make with conforming to IS: 7231 including fixing cistern at required height and level with necessary TW wall plugs, screws, connecting inlet and outlet, connecting the cistern and closet with suitable dia. PVC pipes and fittings conforming to IS:4985 etc., complete as per standard specifications. (Note:- The samples shall be got approved by the Engineer-In-Charge before making bulk order. Prefererd make - PARRYWARE/ HINDWARE model SLIMLINE or other approved equivalent make.)
137	Providing and fixing Viterious china white wall hung water closet Jaquar KUS-WHT-35953-BIUFSM with single piece slim concieled cistern Jaquar JCS-WHT-2400FS and control plate Jaquar opal JCP-CHR-152415 including UF soft close slim seat cover, inlet&outlet gasket, rack bolt and accessories required for fixing complete all as per specifications and as directed by the Engineer-in-charge.
138	Providing and fixing vitreous Floor mounted EWC closet designed for specially abled people it should not have a front that is wide and perpendicular to the-floor at the front of the seat with Seat cover, cistern and fittings from ‘Jaquar of Model DIS-WHT-93753NP180UFSMZ or approved equivalent make with all necessary fittings and fixtures including all connection, embedding in position, commissioning, cleaning etc. all complete all as per specifications and as directed at site by the Engineer-in-Charge.
139	Providing and fixing Viterious china white table top basin Jaquar KUS - WHT-35935 of size 565x425x140 or other equivalent approved make , 32mm Heavy quality C.P. brass waste coupling of standard pattern, cutting holes on the granite slab and making good the walls and testing complete all as per specifications and as directed by the Engineer-in-charge.
140	Providing and fixing white vitreous china flat back urinal basin JAQUAR URS-BLM-13253N of 385X325X635mm size with Ceramic waste dome ZPS-WHT-UA05, fixing accessories set, Sensor Concealed Type Flush Valve for Urinal Complete set with Installation Box & Control Valve (9V transformer) SNR-STL-51077 etc., complete as directed by the Engineer-in-charge.
141	Providing and fixing High Speed Hand Dryer of make TOTO (model TYC322W) or other approved equivalent make with polypropylene body, drying time 5 to 9 seconds, noise level upto 59dB as per specifications and as directed by the Engineer-in-Charge. (Samples to be got approved by the Engineer-in-Charge)
142	Providing and fixing automatic soap dispenser Jaquar SDR-BLC-DJ0160ASN 0.8 liter capacity aluminium body abs finish or approved equivalent as per specifications and as directed by the Engineer-in-Charge. (Samples to be got approved by the Engineer-in-Charge)
143	Providing and fixing liquid soap dispenser in PVC container \\"SDR-WHT-DJ001 F- JAQUAR\\" or approved equivalent make with all accessories including necessary screws for fixing complete all as directed by the Engineer-in-charge.
144	Providing and fixing in position glass shelf with Stainless Steel framework and clamps Jaquar AQN-WHM-7771 or othr approved equivalent make etc., complete all as directed by Engineer-in-charge.
145	Providing and fixing in position single lever tall boy pillar tap with 155mm extension body fixed spout with 600mm long braided hoses Jaquar KUP-ACR-35005BPM or othr approved equivalent make etc., complete all as directed by Engineer-in-charge.
146	Providing and fixing Heavy Quality 15mm nominal bore C.P. Brass Pillar cock with extended lever handle 'Jaquar florentine prime' make or approved equivalent make and type complete all as per specifications and as directed by the Engineer-in-Charge. (Samples to be got approved by the Engineer-in-Charge)
147	Providing and fixing jaquar 32 mm size bottle trap ALD-WHM-769L300X190 wth internal partition with 300mm and 190mm long wall connection pipe and wall flange including required fittings and brackets, cutting holes on the granite slab and making good the walls and testing complete all as per specifications and as directed by the Engineer-in-charge.
148	Providing and fixing paper towel dispenser “Jaquar ” or approved equivalent as per specifications and as directed by the Engineer-in-Charge. (Samples to be got approved by the Engineer-in-Charge)
149	Providing and fixing Heavy Quality C.P. brass 15mm dia Two Way Bib cock “Jaquar ” or approved equivalent as per specifications and as directed by the Engineer-in-Charge. (Samples to be got approved by the Engineer-in-Charge)
150	Providing and fixing Stainless steel double coat hook 'Jaquar' or other approved equivalent make.
151	Providing and fixing Curved shaped urinal partition with frosted glass of 8mm thick Jaquar JSE-CHR-810UC/US 450X or other approved equivalent make etc., complete as directed by the Engineer in charge.
152	Providing and fixing white vitreous china wash basin of size 650 x 450 X 155mm jaquar or equivalent approved make designed for specially abled people with curved finish at front including 32mm Heavy quality C.P. brass waste coupling, bottle trap of standard pattern etc., complete all as per specifications and as directed by the Engineer-in-charge.
153	Providing and fixing in position 100mm dia white glazed vitreous China 'P' or 'S' trap with or without vent holes for urinals and other required location including embedding the trap in cement concrete 1:2:4 using crushed stone sand, including necessary packing with spunyarn & cement mortar using crushed stone sand for jointing complete all as per specification and as directed by the Engineer-in-Charge.
154	Providing and fixing 6mm thick bevelled edge mirror of approved size and shape of make Saint Gobain or other approved equivalent make including making bevelled edge moulding, making minimum 4 holes per mirror to fix the mirror, fixing the mirror using approved fasteners and fixing buttons, etc., all complete as per specification and as directed by Engineer-in-charge.
155	Providing and fixing heavy quality 600mm CP Towel rail of approved make with wall flange including suitable CP screws all complete as per specifications and as directed by Engineer-in-charge.
156	Providing and fixing Grab Bar Vertical Swing Jaquar WAC-SAP- BG0800CSN or approved equivalent make‟ with all accessories including necessary screws/bolt and nut for fixing complete all as directed by the Engineer-in-Charge.
157	Providing and fixing heavy quality 15mm C.P. Brass Long body screw down Bib Cock with wall flange of `JAQUAR' [Continental Series] or approved equivalent make including fixing with suitable SS valve/cup, flange etc., all complete as per specification.
158	Providing and fixing Heavy Quality 15mm nominal bore C.P. Brass Angle cock of Jaquar continental model‟ or approved equivalent make for wash basin inlet / flush cistern etc. as per specifications and as directed by the Engineer-in-Charge (Samples to be got approved by the Engineer-in-Charge)
159	Providing and fixing Heavy Quality C.P Brass Health Faucet with 1.50metres flexible hose (Hand Shower) of “Jaquar continental model” or approved equivalent make and type complete all as per specifications and as directed by the Engineer-in-Charge (Samples to be got approved by the Engineerin-Charge)
160	Providing and fixing 15mm dia. and 450mm long PVC inlet connection with PVC check nuts and washers at both ends suitable for Cold and Hot Water Connection confirming to IS specification of 'PRAYAG / PARRYWARE' or approved equivalent make with ISI mark including fixing etc., all complete as directed by Engineer.
161	Providing and fixing C.P. Brass toilet paper roll holder Recessed type approved with Brass C.P screws of \\"Jaquar\\" make or approved equivalent make and type as directed by the Engineer-in-Charge complete
162	Providing and fixing PVC Nahani trap of FINOLEX/PRINCE or approved equivalent make conforming to the relevant IS code, heavy quality of self cleaning design with 75mm internal dia. and outlet 125mm dia. PVC grating with perforated holes on top, including embedding in cement concrete 1:2:4, forming circular holes by providing and fixing 110mm OD uPVC SWR-TYPE B pipes of required height upto floor level, levelling and rendering smooth, making good the floor and wall etc., complete as per specifications. (Rate shall include cost of PVC pipe and it shall not be paid extra).
163	Providing and fixing best quality of the following dia SWR uPVC pipes - Type A (suitable for ventilation work and rain water applications) conforming to IS: 13592 - latest edition with ISI mark including moulded fittings/specials such as bends, shoes, etc., jointing with seal ring conforming to IS - 5382 leaving 10mm gap for thermal expansion, fixing to the wall with adequate no. of PVC clips for rain water down take pipes etc., all complete as per specifications and as directed by the Engineer in charge.
164	110mm OD SWR - Type A
165	160mm OD SWR - Type A
166	Providing and Fixing Chlorinated Polyvinyl Chloride (CPVC) pipes (Class-I) of SDR-11 of approved make conforming to IS 15778 having thermal stability for hot and cold water supply including providing CPVC plain and brass threaded fittings, fixing the pipe with concealed clamps at 1 m spacing, jointing of pipes and fittings with 1 step CPVC solvent cement, cost of cutting chasses and making good the same, testing of joints complete, etc., all complete as per specification and as directed by Engineer In-Charge. (Note: Concealed work including cutting chases and making good the wall, etc.,)
167	20mm dia Nominal size
168	Providing and Fixing Chlorinated Polyvinyl Chloride (CPVC) pipes (Class-I) of SDR-11 of approved make conforming to IS 15778 having thermal stability for hot and cold water supply including providing all CPVC plain and brass threaded fittings, fixing the clamps at 1m spacing, jointing of pipes and fittings with 1 step CPVC solvent cement, testing of joints, etc., all complete as per specification and as directed by Engineer In-Charge. (Internal work-Exposed on wall)
169	25mm dia Nominal size
170	40mm dia Nominal size
171	50mm dia Nominal size
172	Providing and fixing the following internal dia. Gun metal full way gate valve of \\"Leader\\" or approved equivalent make bearing ISI mark confirming to IS:778 with female ends, screwed bonnet, integral seat, non rising spindle class-I including fixing the valve etc., all complete as directed by the Engineer-in-charge.
173	25mm internal dia. Gate valve
174	50mm internal dia. Gate valve
175	Providing and fixing PTMT ball cock (LP/HP) with epoxy coated aluminium rod with HD ball of make \\"PRAYAG\\" or other approved equivalent make with all accessories in over head water tanks.
176	50mm internal dia.
177	Supplying, laying and jointing of following dia. of Rigid PVC pipe and specials of approved make with ISI mark as per IS 4985:2000 unloading at work site, laying and fixing the pipes and specials with necessary solvent cement of approved make, testing to required working pressure etc., all complete excluding earthwork excavation which will be paid separately under relevant item as per specification and as directed by the Engineer-in-charge.
178	40mm OD PVC pipe of class-3 (6Kg/Sq.cm)
179	50mm OD PVC pipe of class-3 (6Kg/Sq.cm)
180	Providing and laying of following dia. of SWR uPVC pipes - Type B (Suitable for soil and waste discharge system having wall thickness of minimum 3.2 to maximum 3.8mm) of approved make conforming to IS - 13592 - Latest edition including the cost of PVC pasting type specials such as door bends, door tees and cowls etc., heavy quality for soil waste or vent or antisyphonage PVC pipe, fixing with PVC pipe clips or laid embedded under floor slab and fixed to walls wherever required, etc., all complete as per specifications.
181	75mm OD uPVC pipes and specials.
182	110mm OD uPVC pipes and specials.
183	Providing and laying of underground drainage / Sewerage uPVC pipes of SN 8 class (SDR-34) conforming to IS:15328 of approved make suitable for elastomeric sealing ring joints including cost of spigot and socket end pipes with provision for sealing rings, specials, cutting, jointing with elastomeric seals, testing, etc., all complete as per specifications and as directed by Engineer-in-Charge.
184	160mm OD uPVC pipes SN8 Class
185	200mm OD uPVC pipes SN8 Class
186	Providing and constructing GULLY CHAMBER of internal finished size 300 x 300mm including providing, supplying and fixing 150 x 150mm (±10mm) PVC Gully trap with PVC grating at top of approved make including excavation in all types of soils, backfilling, embedding the trap in plain cement concrete 1:4.5:8 using 40mm size granite aggregates and constructing the chamber above the embedded PVC with 110mm thick (plus or minus 5mm) bricks in Cement Mortar 1:5 with well burnt stock bricks, plastering over both internal and external faces of brick work with Cement Mortar 1:3; 12mm thick finished smooth with a floating coat of neat cement on both faces, providing and fixing 400 x 400 x 25mm precast slab in reinforced cement concrete of 1:2:4 using 12mm and below hard broken granite stones including cost of gully trap, chamber etc., all complete as per specification.
187	Providing and placing in Position on Terrace (at all floor levels) of HDPE cylindrical Vertical water storage tank of following capacity conforming to IS:12701 with cover of make SINTEX or approved equivalent make including suitable locking arrangement, fixing with inlet, outlet and over flow pipes with necessary checknuts, etc., all complete as per specification and as directed by Engineer-in-Charge.
188	2000 Litre Capacity
189	Construction of rectangular Manhole/ Inspection Chamber of following size clear internally with brick masonry walls 230mm thick using well burnt chamber bricks in Cement Mortar 1:5 (with necessary corbelling as required), plastering with Cement Mortar 1:3; 12mm thick inside and outside, inside finished smooth with a floating coat of neat cement and outside trowel finished including excavation in all types of soils, back filling, providing and laying bed concrete 150mm thick and having 150mm wide projection on all the sides with Plain Cement Concrete 1:4.5:8 using 40mm maximum size hard granite broken stone, forming, benching and channelling in plain cement concrete 1:2:4 using 20mm maximum size hard broken granite stone, finishing smooth etc., all as per specifications, drawings and as directed at site - to an initial depth upto 1.00 metre.(Note: The rate quoted shall be excluding the cost of cover slab & steel reinforcement which will be paid for separately under relevant item.)
190	900x600mm for initial depth of 1.00 metre.
191	Extra depth of rectangular manhole/ inspection chambers of size 900x600mm over the initial depth of 1.00 metre.
192	1200x900mm for initial depth of 1.00 metre.
193	Extra depth of rectangular manhole/ inspection chambers of size 1200x900mm over the initial depth of 1.00 metre.
194	Making connection of drain or sewer line with existing manhole including breaking in to and make good the walls, floors with cement concrete 1:2:4 mix (1cement:2 coarse sand: 4 graded stone aggregate 20mm nominal size) cement plastered on both side with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement and making necessary channels for the drain, etc., complete.
195	For pipes 250 to 300 mm diameter
196	Supplying laying and jointing of RCC hume pipes with collars of class NP-2 as per IS specifications including aligning to proper level and line as directed at site, jointing with Cement Mortar 1:2, curing, etc., complete as per specification.
197	150mm dia. RCC hume pipes
198	300mm dia. RCC hume pipes
199	450mm dia. RCC hume pipes
200	Part - B. ELECTRICAL WORKS Supply, installation, testing and commissioning of power distribution panels as per the detailed specification. (Refer Sec. V Part A, Clause 3 to 6 and Part -B)
201	415V Class - IV power distribution panel-1- Convention centre as per drawing and specification.
202	415V Class - IV power distribution panel-2- Convention centre as per drawing and specification.
203	415V Class - III -Fire fighting panel- Convention centre as per drawing and specification.
204	415V - Chiller panel- Convention centre as per drawing and specification.
205	Supply, Installation, Testing and Commissioning of following 415V individual Starter modules with enclosure as per the Scope of work.(Refer Sec V Part A, Clause 7 .0, Section V Part -B Clause 5.0) and specification.
206	Starters capacity of 18.5 kW(Star Delta starter)
207	Starters capacity of 5.5 kW(Direct-On-Line)
208	Starters capacity of 1.1 kW(Direct-On-Line)
209	Supply and Embedment of following sizes of flush mounting POWDER COATED TPN/SPN DB Enclosures with Double Door and per Phase isolation DBs consisting of Phase, Neutral and Earth Bus and interconnecting wires etc. at suitable depth in brick work as per the detailed specification and as directed by the Engineer-in-charge.(Refer Sec VI, Clause No.15.2).
210	12 WAY Cat No:DETPI012DD (Vertical) or equivalent make TPN TIER Per Phase Isolation (PPI) DB
211	4 WAY Cat No:DEHPI004DD (Horizontal) TPN TIER Per Phase Isolation (PPI) DB
212	Flexy DB 4 rows of 14 modules IP 43 - IK 09. WITH METAL DOOR. Cat No:507707 or equivalent
213	SPN, 12 Way Distribution Board with all accessories, cat No:507612
214	Supply and Embedment of following sizes Cable end termination box at suitable depth in brick work as per the detailed specification and as directed by the Engineer-in-charge.(Refer Sec VI, Clause No.15.2.2).
215	TPN,12 way Cable end box, Cat No:DBTPI012CB or equivalent suitable for TPN, 12 way TPN TIER Per Phase Isolation Distribution Board Cat No:DBTPI012DD (Vertical)
216	Supply and installation of following sizes of Heavy Duty, Hot Dip Galvanised MS ERW Conduits for Electrical & Communication System with all the required accessories like round JBs, Solid Long Bends, Check Nuts, Nipples, Couplings, Reducers, Copper Clips, Copper Conductor, GI Wire etc, on roof slab, column, beams etc as per the detailed specification. (Refer Sec VI, Clause No.27).
217	25 mm Dia 1.8mm, wall thickness GI Heavy Duty ERW Conduits with 75mm deep junction boxes
218	32 mm Dia 1.8mm, wall thickness GI Heavy Duty ERW Conduits with 75mm deep junction boxes
219	Supply and installation of following sizes of Heavy Duty, Hot Dip Galvanised MS ERW Conduits for Electrical & Communication System with required Solid Long Bends, Check Nuts, Nipples, Couplings, Reducers, Copper Clips, Copper Conductor, GI Wire etc, in Floor, Walls, Brick, Block Masonry, etc. including chasing & replastering as per the detailed specification. (Refer Sec VI, Clause No.27).
220	25 mm Dia 1.8mm, wall thickness Heavy Duty ERW Conduits with 50mm deep junction boxes
221	32 mm Dia 1.8mm, wall thickness Heavy Duty ERW Conduits with 50mm deep junction boxes
222	40 mm Dia 2mm, wall thickness Heavy Duty ERW Conduits with 50mm deep junction boxes
223	Supply and embedment of concealed type Hot dip galvanised MS boxes of the following sizes in RCC/Brick/Concrete Block Masonry with finishing and making good as per the detailed specification. (Refer Sec VI, Clause No.15.10).
224	150(W)X150(H)X80(D)mm, 1.8mm thick sheet Hot dip galvanised MS box
225	300(W)X300(H)X120(D)mm,1.8mm thick sheet Hot dip galvanised MS box
226	400(W)X300(H)X200(D)mm, 1.8mm thick sheet Hot dip galvanised MS box
227	Supply and Embedment of 50mm Deep, Square/Rectangular Concealed type and GI double earthed modular metal boxes of the following types and as specified in RCC/Brick/Concrete Block Masonry with finishing and making good as per the detailed specification. (Refer Sec VI, Clause No.15.12).
228	ONE/TWO Module, with minimum thickness of 1 mm.
229	THREE Module, with minimum thickness of 1 mm.
230	FOUR Module, with minimum thickness of 1 mm.
231	SIX Module, with minimum thickness of 1 mm.
232	Eight Module, with minimum thickness of 1 mm.
233	Twelve Module, with minimum thickness of 1 mm.
234	Supply, embedment and flush mounting of following sizes of Metal Clad Socket in sheet steel enclosure with Plugs and Socket including chipping and finishing as per the detailed specification.(Refer Sec VI, Clause No.15.4).
235	20 AMPS DP Metra Plug and Socket DBs with 20Amps MCB
236	Supply and Installation of MS Brackets, Supports, Frame work, Clamps, Base Channels, etc. fabricated out of angle / Channel / Rods etc. The rate quoted shall include the cost of fabrication / welding, cleaning and painting/ galvanising as follows including supply of required, fasteners, nuts, washers, etc.(Refer Sec VI, Clause No.11).
237	GI: MS fabrication With hot dipped galvanising.
238	Supply and external installation of following sizes of Heavy Duty, Hot Dip Galvanised MS ERW Conduits for Electrical & Communication System with all the required accessories like round JBs, Solid Long Bends, Check Nuts, Nipples, Couplings, Reducers, Copper Clips, Copper Conductor, GI Wire etc. as per the detailed specification. (Refer Sec VI, Clause No.27).
239	25mm dia 1.8mm wall thickness Heavy Duty, Hot Dip Galvanised/ ERW Conduits with 50mm deep junction boxes.
240	25mm GI Flexible Hose
241	Supply and external installation of following sizes of Heavy Duty, PVC circular rigid Conduits for Electrical & Communication System with required Solid Long Bends, Couplings, GI Wire etc, as per the detailed specification.(Refer Sec VI, Clause No.27).
242	25mm Dia, 2mm wall thickness PVC heavy duty round rigid conduits with 50mm deep Junction boxes
243	32mm Dia, 2mm wall thickness PVC heavy duty round rigid conduits with 50mm deep Junction boxes
244	Wiring for lights / fans /sensors/ Timer /Power point with 1100V grade FRLS insulated copper conductor wires in existing concealed/ Exposed PVC / ERW / Flo-coated Metal conduits as per the detailed scope of work, including supply of Wires, switches/ sockets, termination of copper wires at either end by crimping including supply of PVC Sleeves/Ferrules, Copper Crimping Lugs and connecting the wires to various switches, sockets, etc. including testing and commissioning as per the detailed specification.(Refer Sec VI, Clause No.18)
245	Wiring for Light/Sensor/Fan Points with 2 Runs of 1.5 Sq.mm copper wires for Phase & Neutral and 1 Run of 2.5 Sq.mm copper wire for Earth from MCB Distribution Board to Primary light/sensor/fan point through Control Switch Box including 6Amps modular switch.
246	Wiring for Power point with 3 Runs of 2.5 Sq.mm Copper wires for Phase & Neutral and Earth from MCB Distribution Board to Power point through Control Switch Box including 16A modular switch, 6/16 Amps combined shuttered type Socket and 6A modular switch & 3 pin, 6A shuttered type Socket, Modular Plate.
247	Wiring for Power point with 3 Runs of 2.5 Sq.mm Copper wires for Phase & Neutral and Earth from MCB Distribution Board to Power point through Control Switch Box including supply of 16A modular switch, 6/16 Amps combined shuttered type Socket, 3Modular plate 1No.
248	Wiring for Exhaust fan point up to 3Metres height with 2 Runs of 1.5 Sq.mm Copper wires for Phase & Neutral and 1 Run of 2.5 Sq.mm Copper wire for Earth from MCB Distribution Board to Power point through Control Switch Box including supply of 3 pin 6A shuttered type Socket, 2Nos.. 2 Modular plate and 1 No 6A modular switch.
249	Wiring for Power Points with 2 Runs of 4.0 Sq.mm Copper wires for Phase, Neutral and 1 Run of 2.5 Sq.mm Copper wires for Earth from MCB Distribution Board to Single Phase Metal Clad Socket.
250	Wiring for lights / fans /sensors/ Power point with 1100V grade FRLS insulated copper conductor wires in existing concealed/ Exposed PVC / ERW/Flo-coated Metal conduits as per the detailed scope of work, including supply of Wires, switches/ sockets, termination of copper wires at either end by crimping including supply of PVC Sleeves/Ferrules, Copper Crimping Lugs and connecting the wires to various switches, sockets, etc. including testing and commissioning as per the detailed specification.(Refer Sec VI, Clause No.18)
251	Wiring for Light point with 2 Runs of 1.5 Sq.mm Copper wires for Phase & Neutral and 1 Run of 2.5 Sq.mm Copper wire for Earth from Switch box to switch box and further to Light point including 1 No 6A modular switch
252	Wiring for Light point with 2 Runs of 1.5 Sq.mm Copper wires for Phase & Neutral and 1 Run of 2.5 Sq.mm Copper wire for Earth from Switch box to Light point/Ceiling fan including 1 No 6A modular switch
253	Wiring for Light point with 2 Runs of 1.5 Sq.mm Copper wires for Phase & Neutral and 1 Run of 2.5 Sq.mm Copper wire for Earth from Light point to Light point /sensor/contactor
254	Wiring for fan point with 2 Runs of 1.5 Sq.mm Copper wires for Phase & Neutral and 1 Run of 2.5 Sq.mm Copper wire for Earth from Switch box to Fan point including 1 no. 6 A modular switch and 1 no. step type Fan regulator suitable for BLDC fan
255	Wiring for Power point with 3 Runs of 2.5 Sq.mm Copper wires for Phase & Neutral and Earth from Control Switch Box to control switch box including 6A modular switch & 3 pin 6A, shuttered type Socket and 16A modular switch & 6/16A combined shuttered type Socket, Modular plate
256	Wiring for Power point with 3 Runs of 2.5 Sq.mm Copper wires for Phase & Neutral and Earth from Control Switch Box to control switch box including supply of 16A modular switch, 3 pin 6/16 A combined shuttered type Socket, Modular plate.
257	Wiring for Exhaust fan point up to 3Metres height with 2 Runs of 1.5 Sq.mm Copper wires for Phase & Neutral and 1 Run of 2.5 Sq.mm Copper wire for Earth from Switch board to Power point including supply of 3 pin 6A shuttered type Socket, 2Nos.. 2 Modular plate and 1 No 6A modular switch.
258	Supply Installation testing and commissioning of the following MCB on Distribution Boards as per the detailed specification. (Refer Sec VI, Clause No.14.2).
259	6-32 Amps SP MCB (Type-C)
260	40-63Amps, FP MCB (TYPE-C)
261	6-32 Amps DP MCB (DC)
262	Supply fixing testing and commissioning of the following RCCBs on Distribution Boards as per the detailed specification. (Refer Sec VI, Clause No.14.2).
263	RCCB DP 25A 30mA, TYPE AC
264	RCCB DP 63A 30mA, TYPE AC
265	Supply, installation, testing and commissioning of the following SDFU with factory made enclosure with 3Nos. Fuse links on MS frame work as per the scope of work. (MS item will be measured separately). (Refer Sec VI, Clause No.14).
266	SDFU TPN 125A, DIN FUSES with 3Nos. 125A HRC fuse links, Open Execution FN Sheet steel enclosure FN Cat No:SK90486
267	SDFU TPN 63A, DIN FUSES with 3Nos. 63A HRC fuse links, Sheet steel enclosure FN Cat No:SK90484
268	Supply, Loading, Transportation, Unloading at site, installation, Testing and Commissioning of 1100 Volts Grade following sizes of cables in built-in trenches, on walls, poles and through embedded pipes including supply of GI spacer, clamps etc and as per the detailed specification. (Refer Sec VI, Clause No.3)
269	4C X 10 sqmm 1.1kV grade Copper conductor XLPE insulation flat wire armour FRLSH PVC outersheath
270	4C X 16 sqmm 1.1kV grade Copper conductor XLPE insulation flat wire armour FRLSH PVC outersheath
271	Supply, Loading, Transportation, Unloading at site, installation, Testing and Commissioning of 1100 Volts Grade following sizes of control cables in built-in trenches, on walls, poles and through embedded pipes including supply of GI spacer, clamps etc and as per the detailed specification.(Refer Sec VI, Clause No.3 and section V)
272	7C X 2.5 sqmm 1.1kV grade Copper conductor PVC insulation round wire armour FRLSH PVC outersheath
273	Supply, Loading, Transportation, Unloading at site, installation, Testing and Commissioning of 1100 Volts Grade following sizes of cables in built-in trenches, on walls, poles and through embedded pipes including supply of GI spacer, clamps etc and as per the detailed specification. (Refer Sec VI, Clause No.3)
274	3.5C X 185 sqmm 1.1kV grade Aluminium conductor XLPE insulation flat wire armour FRLSH PVC outersheath
275	3.5C X 400 sqmm 1.1kV grade Aluminium conductor XLPE insulation flat wire armour FRLSH PVC outersheath
276	Supply, Loading, Transportation, Unloading at site, Laying, Testing and Commissioning of 1.1 KV grade of following size of the cable through direct in ground including excavation, sand cushioning, protective covering with chamber burnt/cement bricks on sides & top, refilling the trench and providing RCC route indicator etc as required. (Refer Sec VI, Clause No.3)
277	3.5C X 185 sqmm 1.1kV grade Aluminium conductor XLPE insulation flat wire armour FRLSH PVC outersheath
278	3.5C X 400 sqmm 1.1kV grade Aluminium conductor XLPE insulation flat wire armour FRLSH PVC outersheath
279	Loading, Transportation, Unloading at site, installation, Testing and Commissioning of 1100 Volts Grade PVC/HRPVC/XLPE insulated, Stranded Aluminium/copper conductor cables of following sizes in built-in trenches, on walls, poles and through embedded pipes including supply of GI spacer, clamps etc and as per the detailed specification (Note: Cable will be issued free of cost by the department). (Refer Sec VI, Clause No.3)
280	3/3.5/4Core X above 25 & up to 120 sqmm
281	3/3.5/4Core X above 120 & up to 240 sqmm
282	End Termination of the following size Copper Conductor PVC/XLPE Insulated and FRLS sheathed armoured UG Cable using Single Compression, Heavy Duty, Siemens type Brass Gland connecting the cable to the equipment such as Switches/Panel Boards etc. using Copper crimping lugs as directed by Engineer-in-Charge. The rate shall include the cost of supply of Cable Gland and Lugs. The Contractor shall arrange for making holes wherever necessary for fixing cable gland. (Refer Sec VI, Clause No.10.1)
283	4C x 10 Sq.mm including cable gland earthing
284	4C x 16 Sq.mm including cable gland earthing
285	7C x 2.5 Sq.mm including cable gland earthing
286	End Termination of the following sizes of Aluminium Conductor PVC Insulated and sheathed armoured UG Cable using Single Compression, Heavy Duty, Gland connecting the cable to the equipment such as Switches/Panel Boards etc. using Comet or equivalent make Aluminium crimping lugs as directed by Engineer-in-Charge. The rate shall include the cost of supply of Cable Gland and Lugs. The Contractor shall arrange for making holes wherever necessary for fixing cable gland. (Refer Sec VI, Clause No.10.1).
287	3.5/4C x 50/70 sq.mm
288	3.5 x 185 sq.mm
289	3.5 x 400 sq.mm
290	Wiring and termination for Telephone point with 1 Run of 0.61 mm dia, 250 V grade PVC insulated, twin twisted, two pair, tinned copper wire from Telephone Junction Box to Telephone points in concealed conduit/ PVC Trunking including supply of wire and 2 Nos.. 1 module Jack type Telephone Socket with Shutter with Modular plate.(Refer Sec VI, Clause No.18)
291	Supply and fixing following Modular front cover plate on existing modular metal/plastic boxes etc. as required. (Refer Sec VI, Clause No.15.7).
292	One/Two module
293	3 Module
294	4 Module
295	6 Module
296	8 Module
297	12 Module
298	1 Modular dummy plate
299	Supply, transportation, installation, testing and Commissioning of the following type of LED inground uplighter compatible with system wattage not less than 12W with 840 lumens. The system efficacy shall be > 70 lm/W. The luminaire housing shall be pressure die case Al with glass diffuser. Colour Temperature 3000K or Higher with LED binning as per ANSI Bin C78.377A, CRI > 80, Life of LED as per L70 @50K burning hours, Ambient temp -40 to 50 DegC, Driver efficiency>80%, THD<10%, Power factor>0.9, Inbuilt Surge protection in CM ≥ 2.0KV, LED Driver with Voltage range 110-240V AC and Extra safety protection /cut off as per IEC standard, Electrical Safety with Class 1 Insulation. Driver shall be potted driver with three terminals of P,L,E and both driver and luminaire shall be BIS compliance. The ingress protection of the light fixture should be minimum of IP67 and impact resistance of IK10. The beams angle for the symmetrical and asymmetrical shall be selected suitable to the site requirement. The luminaire cable shall be suitable e to enough to connect as per the site requirement.(Refer Sec VI, Clause No.16.1).Cat No. BBP342 G2 D140 30K 110-240V 20 12W
300	Supply, transportation, installation, testing and Commissioning of ModiFly suspended, 120 lm/W, 840 neutral white, to any flexible custom made shapes according to site requirements Cat No. SP800P LED21 840 L60W6 CD. Custom shape-based on site requirement is necessary instead of Triangle shape showing in drawing.(Refer Sec VI, Clause No.16.1).
301	Supply, transportation, installation, testing and Commissioning of 150W LED flood light with a system lumen output of 18100 lumens. The luminaire shall have PDC Al and with toughened glass diffuser. housing and a minimum system efficacy of 120 lumen/watt. CRI> 70 with rated system lifetime of 50,000 hours at L70. It must conform to Protection Classification of IP 66, IK-07, PF>0.95, THD <10%, CCT 5700K. Luminaire shall have input voltage range of 140-270V with cut off and auto restart voltage at 325V AC. Surge shall be 4kV Internal. LED Driver with Voltage range 150-270V AC and Safety Extra Low Voltage Safe level<60V DC as per IEC standard, Electrical Safety with Class 1 Insulation. Driver shall be potted driver with three terminals of P,L,E and both driver and luminaire shall be BIS compliance. (90 deg beam angle - wide) (Refer Sec VI, Clause No.16.1).Cat No.BVP283 LED181 CW FG SY5WB 150W PSU
302	Supply, transportation, installation, testing and Commissioning of IP20 recess LED 2X2 feet compatible,DALI dimmable with system wattage not more than 60W and luminaire lumens not less than 7000 lumens. The system efficacy shall be > 115 lm/W. The housing shall be CRCA housing with diffused optics with PS diffuser for better distribution of light. LED make: that satisfies IEC62471 Photo biological/RoHS Standards with and LED Efficacy of > 150lm/W, Colour Temperature-4000K or Higher with LED binning as per ANSI Bin C78.377A, 120Deg LED Beam Angle, CRI > 80, Life of LED as per L70 > 50000burning hours, Ambient temp-0 to 50DegC, Driver efficiency>85%, THD<10% (At Full load), Power factor>0.95, Inbuilt Surge protection in CM ≥ 4KV, LED Driver with Voltage range 150-270V AC and Safety Extra Low Voltage Safe level<60V DC as per IEC standard, Electrical Safety with Class 1 Insulation. Driver shall be potted driver with three terminals of P,L,E and both driver and luminaire shall be BIS compliance. (Refer Sec VI, Clause No.16.1). Cat No.RC380B LED70S 4000 PSD WH
303	Supply, transportation, installation, testing and Commissioning of IP20 recess LED 2X2 feet compatible with system wattage not more than 36W and luminaire lumens not less than 4200 lumens. The system efficacy shall be 120 lm/W. The housing shall be CRCA housing with diffused optics with PS diffuser for better distribution of light. LED make: that satisfies IEC62471 Photo biological/RoHS Standards with and LED Efficacy of > 150lm/W, Colour Temperature-4000K or Higher with LED binning as per ANSI Bin C78.377A, 120Deg LED Beam Angle, CRI > 80, Life of LED as per L70 > 50000burning hours, Ambient temp-0 to 50DegC, Driver efficiency>85%, THD<10%, Power factor>0.95, Inbuilt Surge protection in CM ≥ 3.5KV, LED Driver with Voltage range 150-270V AC and Safety Extra Low Voltage Safe level<60V DC as per IEC standard, Electrical Safety with Class 1 Insulation. Driver shall be potted driver with three terminals of P,L,E and both driver and luminaire shall be BIS compliance.(Refer Sec VI, Clause No.16.1). Cat No.RC380B LED42S-4000 G6 L60W60 PSU OD S1
304	Supply, transportation, installation, testing and Commissioning of IP20 recess round LED down lighter compatible with system wattage not more than 19W and luminaire lumens not less than 2200 lumens. The system efficacy shall be > 110 lm/W. The housing shall be die-cast aluminium with diffused optics with polycarbonate diffuser for better distribution of light. LED make: that satisfies IEC62471 Photo biological/RoHS Standards with and LED Efficacy of > 150lm/W, Colour Temperature-4000K or Higher with LED binning as per ANSI Bin C78.377A, 120Deg LED Beam Angle, CRI > 80, Life of LED as per L70 > 50000burning hours, Ambient temp-0 to 50DegC, Driver efficiency>85%, THD<10%, Power factor>0.95, Inbuilt Surge protection in CM ≥ 2.5KV, LED Driver with Voltage range 150-270V AC and Safety Extra Low Voltage Safe level<60V DC as per IEC standard, Electrical Safety with Class 1 Insulation. Driver shall be potted driver with three terminals of P,L,E and both driver and luminaire shall be BIS compliance. (Refer Sec VI, Clause No.16.1).Cat No.DN296B LED20S-4000 PSE WH S2 (Cut out dia 150 mm)
305	Supply, transportation, installation, testing and Commissioning of recessed swivel type (wall washer) LED down lighter with system wattage not more than 36W and luminaire lumens not less than 3600 lumens. The luminaire shall be with necessary reflector for good light distribution and less glare. The system efficacy shall be > 95 lm/W. The housing shall be die-cast aluminium with deep recessed optics with low glare and reflector shall be matt black in color. LED modular can be removed from the ceiling without removing the housing/trim from the ceiling. LED make: that satisfies IEC62471 Photo biological/RoHS Standards with and LED Efficacy of > 130lm/W, Colour Temperature-4000K or Higher with LED binning as per ANSI Bin C78.377A, 120Deg LED Beam Angle, CRI > 80, Life of LED as per L70 > 40000burning hours, Ambient temp-0 to 50DegC, Driver efficiency>85%, THD<15%, Power factor>0.95, Inbuilt Surge protection in CM ≥ 3.5KV, LED Driver with Voltage range 150-270V AC and Safety Extra Low Voltage Safe level<60V DC as per IEC standard, Electrical Safety with Class 1 Insulation. Luminaire shall be BIS compliance. (Refer Sec VI, Clause No.16.1).Cat No.RS263B LED36S 840 PSU MB WH (Wall Washer)
306	Supply, transportation, installation, testing and Commissioning of IP20 deep recess round, DALI dimmable LED down lighter compatible with system wattage not more than 28W and luminaire lumens not less than 3600 lumens. The system efficacy shall be > 125 lm/W. The housing shall be CRCA white powder coated with aluminium reflector producing 80 deg & UGR<19 for better distribution of light. LED make: that satisfies IEC62471 Photo biological/RoHS Standards with and LED Efficacy of > 150lm/W, Colour Temperature - 4000K or Higher with LED binning as per ANSI Bin C78.377A, 120Deg LED Beam Angle, CRI > 80, Life of LED as per L70 > 50000burning hours, Ambient temp-0 to 50DegC, Driver efficiency>85%, THD<10% (At Full load), Power factor>0.95, Inbuilt Surge protection in CM ≥ 3.5KV, LED Driver with Voltage range 150-270V AC and Safety Extra Low Voltage Safe level<60V DC as per IEC standard, Electrical Safety with Class 1 Insulation. Driver shall be potted driver with three terminals of P,L,E and both driver and luminaire shall be BIS compliance.(Refer Sec VI, Clause No.16.1). Cat No.DN394B LED36S/840 D200 PSD AL IN
307	Supply, transportation, installation, testing and Commissioning of IP20 deep recess round, DALI dimmable LED down lighter compatible with system wattage not more than 8W and luminaire lumens not less than 1000 lumens. The system efficacy shall be > 125 lm/W. The housing shall be CRCA white powder coated with aluminium reflector producing 80 deg & UGR<19 for better distribution of light. LED make: that satisfies IEC62471 Photo biological/RoHS Standards with and LED Efficacy of > 150lm/W, Colour Temperature - 4000K or Higher with LED binning as per ANSI Bin C78.377A, 120Deg LED Beam Angle, CRI > 80, Life of LED as per L70 > 50000burning hours, Ambient temp-0 to 50DegC, Driver efficiency>85%, THD<10% (At Full load), Power factor>0.95, Inbuilt Surge protection in CM ≥ 3.5KV, LED Driver with Voltage range 150-270V AC and Safety Extra Low Voltage Safe level<60V DC as per IEC standard, Electrical Safety with Class 1 Insulation. Driver shall be potted driver with three terminals of P,L,E and both driver and luminaire shall be BIS compliance. (Refer Sec VI, Clause No.16.1).Cat No.DN391B LED10S/840 D100 PSD AL IN
308	Supply, transportation, installation, testing and Commissioning of 2'X2' architectural decorative Suspended mounted edge lit LED with endorsed lens on each LED with Housing: CRCA powder coated housing with ABS plastic top cover for better aesthetic finish, centre of the luminaire shall be customized to any color of the tile or even it shall be leave as empty and high efficient PMMA diffuser on the wall, electronic driver duly wired upto terminal block, Wattage ≤ 44W Luminaire lumen 3600lm, the tile shall be Mat RED and LED make: that satisfies IEC62471 Photo biological/RoHS Standards with and system Efficacy of > 90lm/W, Colour Temperature - 4000K or Higher with LED binning as per ANSI Bin C78.377A, 120Deg LED Beam Angle, CRI > 80, Life of LED as per L70 > 50000burning hours, Ambient temp-0 to 50DegC, Driver efficiency>85%, THD<10%, Power factor>0.95, Inbuilt Surge protection in CM ≥ 3.0KV, Driver Voltage range 150-270V AC and Safety Extra Low Voltage Safe level<60V DC as per IEC standard also driver shall be capable of auto restart post auto shut off if the voltage greater 325V, Electrical Safety with Class 1 Insulation, Luminaire luminous Efficacy≥100lm/W. Driver shall be potted driver and both driver and luminaire shall be BIS compliance. driver shall be potted driver and both driver and luminaire shall be BIS compliance. (Refer Sec VI, Clause No.16.1). Cat No.SP740B LED36S/840 W60L60 PSU WH
309	Supply, transportation, installation, testing and Commissioning of LED highbay symmetric beam luminaire with housing made of die-cast aluminium of system wattage consisting 80W. The luminaire shall be with dedicated optics to provide precise light distribution of symmetric wide beam angle (90 deg beam). The luminaire shall be designed to meet its specifications on performance & lifetime at a design ambient temperature of 45 deg C and operating temperature range 0-50° C. A specially designed heat management system to ensure luminous efficacy 130 lm/ W for the system and ensure lumen depreciation upto 30% over 50000 burning hours. The luminaire is designed to meet IP 65 and IK 08 classification and is compliant with relevant immunity, safety and performance and EMI/EMC standards. The system lumens shall not be less than 10000 lumens with 4000K CCT. The CRI shall be > 70. The luminaire shall be able operate from 120 - 270V AC, 50Hz with > 0.95 PF & THD <=10%. The LEDs shall be of SMD type (not COB type). The luminaire supplier shall submit the LM79 and LM80 report of the luminaire from the approved NABL accredited laboratory. The luminaire shall be with inbuilt surge protection of 6kV. The driver efficiency shall be > 90%. The driver shall be able to withstand 440V (Phase to Phase Protection for 8 Hrs and High cut @ 325±15V and auto Restart. (Refer Sec VI, Clause No.16.1).Cat No.BY710P LED100S 4000 WB S PSU
310	Supply, transportation, installation, testing and Commissioning of IP20 LED ring suspended (600 MM dia) feet compatible with system wattage not more than 30W and luminaire lumens not less than 2400 lumens. The system efficacy shall be > 80 lm/W. The housing shall be Aluminium housing with diffused optics with PS diffuser for better distribution of light. LED make: that satisfies IEC62471 Photo biological/RoHS Standards with and LED Efficacy of > 150lm/W, Colour Temperature-4000K or Higher with LED binning as per ANSI Bin C78.377A, 120Deg LED Beam Angle, CRI > 80, Life of LED as per L70 > 50000burning hours, Ambient temp-0 to 50DegC, Driver efficiency>85%, THD<10%, Power factor>0.95, Inbuilt Surge protection in CM ≥ 4KV, LED Driver with Voltage range 150-270V AC and Safety Extra Low Voltage Safe level<60V DC as per IEC standard, Electrical Safety with Class 1 Insulation. Driver shall be potted driver with three terminals of P,L,E and both driver and luminaire shall be BIS compliance.(Refer Sec VI, Clause No.16.1). Cat No.SP682P 30W‐4000 PSU OD DIA600H75 DNR WH(Decorative pendant light)
311	Supply, transportation, installation, testing and Commissioning of deep recessed COB fixed LED down lighter with system wattage not more than 40W and luminaire lumens not less than 4000 lumens. The luminaire shall be with necessary reflector for good light distribution and less glare. The system efficacy shall be 100 lm/W. The housing shall be die-cast aluminium with deep recessed optics with low glare and reflector shall be matt black in color. LED modular can be removed from the ceiling without removing the die cast Al housing/trim from the ceiling. LED make: that satisfies IEC62471 Photo biological/RoHS Standards with and LED Efficacy of > 130lm/W, Colour Temperature-4000K or Higher with LED binning as per ANSI Bin C78.377A, 120Deg LED Beam Angle, CRI > 80, Life of LED as per L70 > 30000burning hours, Ambient temp-0 to 40DegC, Driver efficiency>85%, THD<10%, Power factor>0.9, Inbuilt Surge protection in CM ≥ 4KV, LED Driver with Voltage range 150-270V AC and Safety Extra Low Voltage Safe level<60V DC as per IEC standard, Electrical Safety with Class 1 Insulation. Luminaire shall be BIS compliance. Wide beam angle distribution - 60 deg (Refer Sec VI, Clause No.16.1).Cat No.RS261B LED40S/840 PSU WB WH Cutout dia 196mm
312	Supply, transportation, installation, testing and Commissioning of 5m IP44 LED Neon Flex strip and LED should be with silicon housing and highly efficient electronics with LED system to offer long useful life even in adverse application and environmental conditions. The system wattage shall be 16W/m with system lumens of 800 lumens. LED make: that satisfies IEC62471 Photo biological/RoHS Standards with and Colour Temperature-2700-6500K with LED binning of SDCM<3 as per ANSI Bin C78.377A, 110Deg LED Beam Angle, CRI > 90, Life of LED strip as per L70 > 30000burning hours, Ambient temp-0 to 35DegC, Driver efficiency>85%, THD<20%, Power factor>0.9, Voltage range 24VDC ±10% .LED strip should be with IP44 also BIS & CB certified.(Refer Sec VI, Clause No.16.1).Cat No.LS360
313	DIMMING CONTROLS: Supply, installation, testing and commissioning of Dynalite Lighting Controller,(DDBC320-DALI v3 DALI CONTROLLER), DDNG 485 (network Gateway), DDNP1501 (Dynet power supply), PDEG (Ethernet Gateway), DDNG232(AV integration), Software with system for CONVENSION CENTRE as per (Section V PART- C, Clause 1.0 to 8.0)
314	Supply, transportation, installation, testing and Commissioning of Darklit adjustable down lights recess 30W 4000K CCT NON DIM Black (PC) Prime 15 beam angle (Refer Sec VI, Clause No.16.1). Cat No. RDDOTO3040NDBKP015
315	Supply, transportation, installation, testing and Commissioning of the following type of Surface mounted luminaires. (Refer Sec VI, Clause No.16.1). - Catalogue No : WAND K 30W 5700K code SLWKY03057NDWEP04C22 -SURFACE LIGHTS NONDIM WITH CUSTOMIZED CLAMP OF 30 DEG. TILT WHITE (PC) 4FEET- PRIME or equivalent and Lamp Type LED
316	Supply, transportation, installation, testing and Commissioning of the following type of Surface mounted luminaires. (Refer Sec VI, Clause No.16.1). - Catalogue No : WAND K 9W 5700K Code- SLWKB00957NDWEP0002C01-2Feet Batten PRIME or equivalent and Lamp Type LED
317	Supply, transportation, installation, testing and Commissioning of the following type of Surface mounted luminaires. (Refer Sec VI, Clause No.16.1). - Catalogue No : DICE 12W 5700K Item code SLD0001257NDWEPor Equivalent and Lamp Type LED
318	Supply, transportation, installation, testing and Commissioning of the following types of Suspended luminaires. (Refer Sec VI, Clause No.16.1). - Catalogue No : CANE STD LINEAR PENDANT 40W, 5700K-4FT Item code LPC0104057NDWEP0DL4C01 with down rod replacement fixing accessories or Equivalent and Lamp Type LED
319	Supply, transportation, installation, testing and Commissioning of the following type of Wall (surface) mounted luminaires. (Refer Sec VI, Clause No.16.1). - Catalogue No : ILB0S00857NDGYP BASE LED Low bay 8w 5700k CCT IP 65 Non Dim Grey(PC) Prime and Lamp Type LED
320	Supply, transportation, installation, testing and Commissioning of the following type of Surface mounted luminaires. (Refer Sec VI, Clause No.16.1). - Catalogue No : DICE 24W 5700K Item code SLD0002457NDWEP or Equivalent and Lamp Type LED
321	Supply, transportation, installation, testing and Commissioning of the following type of Recess mounted luminaires. (Refer Sec VI, Clause No.16.1). - Catalogue No : FULLLIT SQ STD 24W 5700K Item code PRF0002457NDWEP or equivalent and Lamp Type LED
322	Supply Installation testing and commissioning of 2 KVA ,415V AC to 12V DC SMPS with enclosure .(Refer section V Part -A, Clause 8.0.)
323	Supply installation testing and commissioning of auditorium seat light and signage light.as required as per site condition Cat No. (LTIKONV312VSM80GSE - LT IKON V3 GS SM LED Module, 12V, 1W, 165deg beam, 8000K CCT, IP66). Refer section V Part -A Clause 9.0.
324	Supply, transportation, installation, testing and Commissioning of the motor ON & OFF Push Button with enclosure . (Refer section V Part -A Clause 10.0)
325	Supply, Installation, testing and commissioning of following sizes of BLDC ceiling Fans suitable for electronic regulator for speed adjustment and safety steel rope with 3 Core, 1.5 Sq.mm flexible copper cable including earth connection. Supply and fixing of regulator is not included in the scope of this item. (Refer Section V & Sec VI, Clause No.17.1).
326	1200mm Sweep BLDC ceiling fan
327	Supply, installation, testing and commissioning of following sizes of Wall Mounting Exhaust Fans including supply of Aluminium grill bracket with Stainless Steel Bolts for mounting of Exhaust Fan & Aluminium grill bracket and 3 Core, 1.5 Sq.mm (14/0.3) PVC insulated & FRLS sheathed copper flexible cable of required length as per the detailed specification. (Refer Sec VI, Clause No.17.2).
328	300 mm Dia Turbo Heavy Duty Exhaust Fan
329	Rod Earthing
330	Supply installation and testing of Maintenance free earthing system TRIPOLAR (3x10feetx5/8inch copper bonded steel rod, 55 kg Ground Enhancing Material (GEM) ) as per IS: 3043 including RCC Chamber and RCC cover as per Drawing No.IGC/ESD/5060/1008/1 enclosed . (Refer Sec VI, Clause No.12.12).
331	Supply installation and testing of Maintenance free earthing system (16mm Stainless steel solid Rod, 22 kg Ground Enhancing Material (GEM) ) as per IS: 3043 including RCC Chamber and RCC cover as per Drawing Nos...IGC/ESD/5060/1009/1 & IGC/ESD/5060/1008/1 are enclosed. (Refer Sec VI, Clause No.12.12).
332	Supply, fabrication and installation of the following size of Hot dip Galvanised GI Flats including excavation and refilling as per the detailed specification. No cutting or drilling permitted after galvanisation.Refer Sec VI, Clause No.12.9).
333	25 x 6 mm GI flat
334	Supply and installation of the following sizes of copper wires including excavation and refilling as per the detailed specification. (Refer Sec VI, Clause No.12.8).
335	8 SWG copper wire
336	Supply, fabrication and installation of the following size of Hot dip Galvanised GI Flats in Built in trenches on walls, poles, RCC Concrete and through embedded pipes as per the detailed specification. No cutting or drilling permitted after galvanisation. (Refer Sec VI, Clause No.12.9).
337	25 X 6 mm GI flat
338	Supply and installation of the following sizes of copper wires in built in trench as per the detailed specification. (Refer Sec VI, Clause No.12.8)
339	8SWG copper wire
340	14 SWG Copper Wire
341	Supply, cleaning the floor, proper pasting and installation of following insulating mat as per specification. (Refer Sec VI, Clause No.25).
342	2.0 mm thickness, Max useable voltage 3.3kV, AC Proof voltage 10kV for 3 minutes, AC dielectric strength 30kV RMS Insulating Mat confirming to IS:15652
343	Assembling, installation, testing and commissioning of MCB DB enclosure already embedded in the wall including supply of Engraved Circuit Identification Plate and Danger Board as per the detailed specification for the following size of MCB DBs. (Refer Sec VI, Clause No.15.3).
344	TPN, 12 Way Distribution Board
345	Supply, Loading, Transportation, Unloading at site, installation, Testing and Commissioning of one number of armoured Telephone cable of following sizes in direct in ground including excavation, sand cushioning, protective covering with chamber burnt/cement bricks on sides & top, refilling the trench and providing RCC route indicator etc as required. (Refer Sec VI, Clause No.3 )
346	50 Pairs 0.63mm PIJF telephone cable
347	Supply, Loading, Transportation, Unloading at site, installation, Testing and Commissioning of one number armoured Telephone cable of following sizes in built-in trenches, on walls, poles and through embedded pipes including supply of GI spacer, clamps etc and as per the detailed specification. (Refer Sec VI, Clause No.3)
348	20 Pairs 0.63mm PIJF telephone cable
349	50 Pairs 0.63mm PIJF telephone cable
350	Wiring for lights / fans /sensors/ Power point with 1100V grade FRLS insulated copper conductor wires in existing concealed/ Exposed PVC / ERW / Flo-coated Metal conduits as per the detailed scope of work, including supply of Wires, termination of copper wires at either end by crimping including supply of PVC Sleeves/Ferrules, Copper Crimping Lugs and connecting the wires to various switches, sockets, etc. including testing and commissioning as per the detailed specification. (Refer Sec VI, Clause No.18)
351	Wiring with 1 Run of 1.5 Sq.mm Copper wire
352	Wiring with 1 Run of 2.5 Sq.mm Copper wire
353	Supply and Installation of Rust resistant non corrosive 10 mm dia Copper Bonded Steel round conductor used for Earth termination on the roof top /over metal sheet as per the detailed specification and drawing. The item is also inclusive of supply and installation of Stainless steel Conductor Holder for fixing the 10 mm dia round conductor at each Metres on the wall/ roof, Stainless steel 304 Grade Cross Connector for 10 mm Copper bonded conductor at cross/Tee junction, Straight Connector, Bridging cable with suitable connector to connect ACP/facade with the aluminium conductor, connecting point made of stainless steel for terminating 10mm copper conductor, Stainless Steel Metal roof holder or Folding Clamp. As per (Section -V Part-D)
354	Supply and installation of 2 metre VAT with Wall clamp support – VAT 2 metre (Ø20 x 1000 mm Copper Rod + Ø38 x 1000 mm SS Pipe) + Wall Clamp made up of stainless steel for holding 40 mm Dia of air terminal rod on the side walls to meets the requirement for IS/IEC - 62305.(WC40ss) + Connecting point made of stainless steel for terminating the 8-10mm Dia conductor to meets the requirement. CAPE Type : VAT 2 As per (Section -V Part-D)
355	STRUCTURAL RISER / DOWN CONDUCTOR
356	Supply and installation of Rust resistant non corrosive 10 mm dia Copper Bonded Steel round conductor used for structural riser/ down conductor in side the concrete columns as per the detailed specification and drawing. The item is inclusive of supply and installation of Bonding clamp for interconnecting Round Conductor with reinforcement rebar at every 3Metres (or as required) inside the concrete to meet the requirements of IS/IEC 62305, stainless steel Straight Connector at every 4Metres (or as required) of integrated down conductor and should be tested for electrical resistivity, mechanical load to meet the requirement. As per (Section -V Part-D)
357	Supply and installation of stainless steel Earth stud of dimension 69 x 69 mm integrated inside concrete and required connections. Cape Type No. ES 1 RA1 ( Article No. 401 510 ) As per (Section -V Part-D)
358	STRUCTURAL EARTHING
359	Supply and installation of Rust resistant non corrosive 10 mm dia Copper Bonded Steel round conductor used for Earth termination inside soil. The item is also inclusive of supply and installation of stainless steel Straight Connector at every 4Metres of conductor(or as required) and should be tested for electrical resistivity, mechanical load to meet the requirement for IS - 62305, Corrosion Bitumen tape for inside soil and Stainless steel 304 Grade Cross Connector for 10 mm Copper bonded conductor at cross/Tee junction. As per (Section -V Part-D)
360	Supply and installation of stainless steel equipotential Bonding Rail (50 X 500 X10 MM) to meet the requirements of IS-2305. CAPE Type: EBRH 55010 (Article No. 400 751)As per (Section -V Part-D)
361	Supply and Installation of laminated Hylam sheet of 3mm thickness over the boxes and as per the detailed specification.
362	Supply and installation of 8 Ways Brass Neutral Link, 8 Screw Terminal Grounding Bar Block for wire looping and earthing with P.B.T insulator Base. (Refer Section-V - Part -A Clause 11.0)
363	Loading, Transportation, Unloading at site, installation, Testing and Commissioning of one number PVC/HRPVC/XLPE insulated, PVC sheathed armoured power cable of 11kV grade, the following sizes of cable direct in ground including excavation, sand cushioning, protective covering, with two sides with chamber burnt/cement brick & top PCC slab, RCC route marker and refilling the trench etc as required. (Note: Cable will be issued free of cost by the department). (Refer Sec VI, Clause No.3)
364	Above 3C x 120 sq.mm but not exceeding 3C x 240 sq mm
365	Loading, Transportation, Unloading at site, installation, Testing and Commissioning of 11kVolts Grade XLPE/HRPVC insulated, Stranded Aluminium conductor cables of following sizes in built-in trenches, on walls, poles and through embedded pipes including supply of GI spacer, clamps etc and as per the detailed specification (Note: Cable will be issued free of cost by the department). (Refer Sec VI, Clause No.3)
366	3 Core X above 120 to up to 240 sqmm
367	Retrieval of the already laid one number PVC/HRPVC/XLPE insulated and PVC sheathed power cable of 11 KV grade of following sizes laid direct in ground including retrieval of end termination, excavation of trenches, retrieving of bricks, back filling and Re - laying the same cable direct in ground by using retrieved bricks including transportation of cables, excavation and backfilling of soil, supply of sand, shortage bricks etc as per the detailed specification. (Refer Sec VI, Clause No.7)
368	3 Core Above 120 & Upto 240 sqmm
369	Retrieval of the already laid one number 11kV (E), 3 Core, Aluminium Conductor, XLPE insulated Power cables of following sizes in built-in trenches, on walls, poles and from embedded pipes including removal of GI spacer, clamps etc and relaying the same cable in built-in trenches, on walls, poles and through embedded pipes using the retrieved Spacer & clamp & supplying the shortage Spacer & clamp if any as per the detailed specification. (Refer Sec VI, Clause No.7)
370	3 Core Above 120 & Upto 240 Sqmm
371	Retrieval of the already laid one number PVC/HRPVC/XLPE insulated and PVC sheathed power cable of 1.1 KV grade of following sizes laid direct in ground including removal of end termination, excavation of trenches, retrieving of bricks, back filling and Re - laying the same cable direct in ground by using retrieved bricks including transportation of cables, excavation and backfilling of soil, supply of sand & shortage bricks etc as per the detailed specification. (Refer Sec VI, Clause No.7)
372	3/3.5/4 Core Upto 25 sqmm
373	3/3.5/4 Core Above 25sqmm & upto120 sqmm
374	3/3.5/4 Core Above 120sqmm & upto 240 sqmm
375	3/3.5/4 Core Above 240sqmm & upto 400 sqmm
376	Retrieval of the already laid one number 1100 Volts Grade XLPE/HRPVC insulated, Stranded Aluminium conductor cables of following sizes in built-in trenches, on walls, poles and from embedded pipes including removal of GI spacer, clamps etc and relaying the same cable in built-in trenches, on walls, poles and through embedded pipes using the retrieved spacer & clamp & supplying the shortage spacer & clamp if any as per the detailed specification. (Refer Sec VI, Clause No.7)
377	upto 3/3.5/4 C X 25 Sqmm
378	3/3.5/4 Core Above 25 & Upto 120 Sqmm
379	3/3.5/4 Core Above 120 & Upto 240 Sqmm
380	3/3.5/4 Core Above 240 & Upto 400 Sqmm
381	Loading, Transportation, Unloading at site, Laying, Testing and Commissioning of one number PVC/HRPVC/XLPE insulated and PVC sheathed Stranded Aluminium/copper conductor power cable of 1.1 KV grade of following sizes direct in ground including excavation, sand cushioning, protective covering with chamber burnt/cement bricks on sides & top, refilling the trench and providing RCC route indicator etc as required (Note: Cable will be issued free of cost by the department). (Refer Sec VI, Clause No.3)
382	3/3.5/4 Core X above 25 to 3/3.5/4 Core X up to 120 sqmm
383	3/3.5/4CX Above 120 Sq.mm but not exceeding 3.5/4CX 240 sq.mm
384	Supply, installation, testing and commissioning of the following Raychem make Heat Shrinkable Cable Straight Through Jointing Kits (Mechanical Connector type/Crimping type) Rayfit tubing for 3 Core Aluminium Conductor, 11 kV (E), XLPE insulated cables of following sizes including excavation of soil, backfilling etc as specified. (Refer Sec VI, Clause No.10.6).
385	Straight Through Joint (Crimping type) for 3 Core x 185 Sq. mm
386	Supply, installation, testing and commissioning of Raychem make the following Heat Shrinkable Cable end Termination without gland for 3 Core Aluminium Conductor, 11 kV, XLPE insulated cables of following sizes. (Refer Sec VI, Clause No.10.5).
387	3 Core x 185 Sq.mm XLPE (Indoor)
388	Supply, installation, testing and commissioning of the following Raychem make Heat Shrinkable Cable Straight Through Jointing Kits (Crimping type) for 3.5 Core Aluminium Conductor, 1.1 kV (E), PVC/XLPE insulated cables of following sizes as specified. Excavation will be measured separately. (Refer Sec VI, Clause No.10.6).
389	Straight Through Joint (Crimping type) for 3.5 Core, 70-95 Sq. mm
390	Straight Through Joint (Crimping type) for 3.5 Core 120- 185 Sq. mm
391	Straight Through Joint (Crimping type) for 3.5 Core x 400 Sq. mm
392	Construction of Rectangular Electrical HT Cable joints Chamber of size 1600x700mm - upto a initial depth of 1.35 Metres
393	Supply and installation of following sizes of HDPE Pipes Direct in Ground.
394	Supply and installation of 6Metres length DWC HDPE pipes,200 mm OD / 175 mm ID with Coupler as required including excavation at a depth of 1200 mm in all types of soil, backfilling complete as directed by Engineer-in-Charge. 6Metres will be measured as 1No. (Refer Sec VI, Clause No.8.3).
395	Supply and Installation of following sizes of Cable entry arrangement with stainless steel pipes welded on MS plate with plastic end cap approved by Engineer-in-charge for cable entry at cable trench mouth as per the following drawing and specification. (Refer Sec VI, Clause No.9).
396	1000mm X 1000mm size as per Drawing No. IGC/ESD/4011/2001/2
397	Supply and installation of 300mm(W) x 100mm(H) x 3mm thick Hot dip Galvanised Perforated type Cable Tray with 2 Nos.. Coupler Plates and required accessories viz. Elbow, Bends, Tee, Cross and Reducer, etc as per the detailed specification.
398	Supply and installation of 150mm(W) x 100mm(H) x 3mm thick Hot dip Galvanised Perforated type Cable Tray with 2 Nos.. Coupler Plates and required accessories viz. Elbow, Bends, Tee, Cross and Reducer, etc as per the detailed specification.
399	Internal Intercom Telephone System Supply and installation of Powder coated MS boxes with SS Krone base module (i.e. For mounting of telephone Krone disconnection modules) for the following D.B sizes. (Ref. Sec VI, Clause No.15.10 & Sec V).
400	500(W)x500(H)x150(D) 2.5 mm thick MS Box - (100L+100R = 200 pair) (Note: L - Left side Krone base, R- Right side Krone base fixing) * with Krone Module
401	900(W)x750(H)x200(D) 3.0 mm thick sheet MS Box - (100x2L+100x2M+100x2R = 600 pair) (Note: L - Left side Krone base, R- Right side Krone base fixing) * with Krone Module
402	Supply, Loading, Transportation, Unloading at site, installation, Testing and Commissioning of one number of armoured Telephone cable of the following sizes in built -in trenches, on walls, poles and through embedded pipes including supply of GI spacer, clamps etc and as per the detailed specification. (Refer Sec VI, Clause No.3 & Section V)
403	10 Pairs 0.63 mm PIJF telephone cable.
404	20 Pairs 0.63 mm PIJF telephone cable.
405	Supply,Loading, Transportation, Unloading at site, installation, Testing and Commissioning of one number of armoured telephone cable of following sizes in direct in ground including excavation, sand cushioning, protective covering with chamber burnt/cement bricks on sides & top, refilling the trench and providing RCC route indicator etc as required. (Refer Sec VI, Clause No.3 & Section V)
406	100 pairs 0.63mm PIJF telephone cable
407	200 pairs 0.63mm PIJF telephone cable
408	Network & CCTV Supply, Laying, Testing and Commissioning of CAT 6A – UTP Cable 4 Pair as per the specification
409	Supply, Installation, Testing and Commissioning of 28-port Gigabit Switch including 10GbE (2) SFP+ and 1GbE (2) as per the specification
410	Supply, Installation, Testing and Commissioning of 16 Port Gigabit PoE Switch including 2 No. of SFP Port as per the specification
411	Supply, Installation, Testing and Commissioning of CAT 6A – 24 Port Patch Panel with all Accessories as per the specification
412	Supply of Cat 6A Patch Cord (1.5m) as per the specification
413	Supply of Cat 6A Patch Cord (3 m) as per the specification
414	Supply, Installation, Testing and Commissioning of 24U Rack with Accessories as per the specification
415	Supply, Installation, Testing and Commissioning of 9U Rack with Accessories as per the specifcation
416	Supply, Installation, Testing and Commissioning of Unarmoured OFC 6 core cable - Single Mode as per the specification.
417	Supply, Installation, Testing and Commissioning of Armoured OFC 12 core cable - Single Mode as per the specification.
418	Supply of LC to SC Patch cord (3 m) as per the specification
419	Supply of Gigabit Ethernet 1000BASE-LX10 as per the specification
420	Supply, Installation, Testing and Commissioning of fully loaded LIU Rack Mountable as per the specification
421	OFC Termination using fusion splicer in termination box/enclosure & prepare report of power loss along with distance from the Light Interface Unit using OTDR as per the specification
422	Supply, Installation, Testing and Commissioning of RJ 45- Ethernet - Face Plate Dual with Keystone Jack for Cat 6A as per the specification
423	Supply, Installation, Testing and Commissioning of RJ 45- Ethernet - Face Plate Single with Keystone Jack for Cat 6A as per the specification
424	Supply and Embedment of 50mm Deep,Square/Rectangular Concealed type and GI doubleearthed modular metal boxes of the following types and as specified in RCC/Brick/Concrete Block Masonry withfinishing and making good. ONE/TWO Module
425	Supply and installation of following sizes of HDPE Pipes Direct in Ground.Supply and installation of PLB 40/33mm HDPE Ducts including excavation for routing of Power/Telephone Cables.
426	Supply and installation of following sizes of PLB HDPE pipes on Floor, column, beams etcincluding chasing and replastering.
427	Installation of HDPE pipe across the RoadInstallation of 6mtr length HDPE pipes, 40/33mm with Coupler as required including cutting for crossing of existing road and excavation at a depth of 1200mm in all types of soil, backfilling, normalisation of road etc complete as directed by Engineer-in-Charge. 6 mtr will be measured as 1No.
428	Supply, Installation, Testing and Commissioning of 32 Channel Network video Recorder RAID Support along with HDD to store video footage for continuous recording in h.265+ format as per the specification
429	Supply, Installation, Testing and Commissioning of 4 MP IP Dome Camera with IP 55 Protection Junction box of 100 x 100 x 50 and accessories as per the specification
430	Supply, Installation, Testing and Commissioning of 4 MP IP Bullet Camera with IP 55 Protection Junction box of 100 x 100 x 50 and accessories as per the specification
431	Supply, Installation, Testing and Commissioning of Professional Display 55” operating continuously 24/7 as per the specification
432	Air-Cooled Scroll Chiller (80 TR): Supplying, installing, testing and commissioning factory-assembled, air-cooled chilled water chiller of 80 TR (≈280kW) capacity, suitable for comfort and/or process air-conditioning applications, complete in all respects. The chiller shall be designed for 35°C ambient (rated) and suitable for operation up to 46°C, delivering chilled water at 7°C outlet with 12°C inlet (ΔT = 5°C). The unit shall be equipped with minimum four (4) or more hermetic scroll compressors using R-410A / R-134a refrigerant (ODP = 0, low GWP preferred), with stepwise or digital capacity control in minimum 25% steps for high part-load efficiency and redundancy.The evaporator shall be shell & tube or brazed plate heat exchanger, designed for minimum 10 bar working pressure, with chilled water flow rate of approximately 200-240 USGPM and water pressure drop not exceeding 60 kPa. The condenser shall be air-cooled type with copper tubes and aluminium fins, complete with axial flow fans, statically and dynamically balanced, driven by TEFC fan motors, IP55 protection, Class-F insulation.The unit shall have maximum power consumption not exceeding 0.95–1.05 kW/TR at full load, and noise level limited to 75 dB(A) at 1 m free field.
433	The chiller shall be suitable for 415 V ±10%, 50 Hz, 3-phase power supply, and provided with a microprocessor-based control panel with LCD display, complete with HP/LP cut-outs, flow switch, phase failure protection, anti-short cycle protection, and all standard safety interlocks. Modbus/BACnet communication shall be provided for BMS integration.The complete assembly shall be housed in a weatherproof, powder-coated GI steel enclosure, mounted on spring/neoprene vibration isolators, factory tested at rated conditions, and conforming to ASHRAE-90.1, AHRI and IS 1391 (Part-2) standards. The scope shall include all accessories, mounting hardware, interconnecting works as required for proper operation, and 12 months warranty from commissioning or 18 months from supply, whichever is earlier. Approved makes: Voltas / Blue Star / Carrier / Daikin or equivalent.
434	Double Skin Air Handling Unit: Supplying, installing, testing and commissioning floor-mounted, horizontal, double-skin Air Handling Unit (AHU) of following capacity suitable for central air-conditioning applications, complete in all respects. The AHU shall be designed to handle minimum 15% fresh air through weatherproof fresh air louvers with bird and insect screen, with the balance air through return air boxing, and provided with a factory-fabricated fresh air and return air mixing section complete with volume control dampers.The AHU casing shall be of double-skin construction with 50 mm thick panels, comprising outer skin of 0.8 mm GI and inner skin of 0.6 mm GI, insulated with 50 mm thick PUF/EPS insulation of minimum density 40 kg/m³, mounted on aluminium extruded or powder-coated GI frame. The unit shall be complete with 6-row chilled water cooling coil, designed for 12°C/7°C chilled water conditions, with seamless copper tubes and hydrophilic-coated aluminium fins. A double-sloped, insulated SS-304 drain pan shall be provided for effective condensate drainage.The AHU shall be provided with EC plug fans with multiple fan arrangement and N+1 redundancy, driven by integrated IE4 efficiency EC motors with in-built electronic speed control for energy-efficient operation. The filter section shall comprise 10-micron washable pre-filters, housed in GI/aluminium filter housing with gasketed frames. UV-C germicidal lamps (254 nm) shall be installed in the coil section, complete with door interlock and limit switches for operational safety.
435	The unit shall include double-skin insulated return air plenum/boxing with volume control damper, motorized or manual fresh air damper, gasketed and lockable access doors, and door limit switches interlocked with fan operation and UV system. Instrumentation shall include filter differential pressure switch and temperature sensors, with an AHU local control panel for monitoring and control. The AHU shall be designed for noise level not exceeding 65 dB(A) at 1 m free field, with casing leakage class as per EN 1886, finished with powder coating, and factory tested.The complete unit shall conform to IS 1391 and EN 1886 standards and shall carry a warranty of 12 months from the date of commissioning. Approved makes: Blue Star / Voltas / Trane / Carrier / Daikin or equivalent.40 TR at 16000 CFM, 30mm W.C ESP
436	Treated Fresh Air (TFA) Unit with Enthalpy Recovery: Supplying, installing, testing and commissioning factory-assembled Treated Fresh Air (TFA) Unit suitable for 100% fresh air ventilation with energy recovery, complete in all respects. The unit shall be designed for supply and exhaust air handling, with an air flow capacity of approximately 2100 CFM (≈3600 CMH), suitable for design ambient conditions of 38°C and 75% RH, and without cooling coil. The unit shall be suitable for floor-mounted or ceiling-suspended installation, as required at site.The TFA unit casing shall be of double-skin panel construction, 25–50 mm thick, fabricated from GI sheets with minimum thickness of 0.8 mm outer skin and 0.6 mm inner skin, insulated with PUF/EPS insulation of minimum density 40 kg/m³, mounted on aluminium extruded or powder-coated GI frame, and finished with corrosion-resistant powder coating. The casing leakage class shall comply with EN 1886, and the unit shall be provided with hinged, gasketed and lockable access doors for maintenance.The unit shall be equipped with a rotary enthalpy heat recovery wheel with minimum 70% combined sensible and latent efficiency, using polymer/silica-gel coated desiccant matrix media, complete with geared motor and belt drive, peripheral and radial sealing arrangement, and purge sector to minimize cross-contamination between supply and exhaust air streams
437	The TFA unit shall be provided with EC plug fans for both supply and exhaust air, driven by integrated IE4 efficiency EC motors, with in-built electronic speed control, and minimum fan efficiency of 70% at design point, suitable for the specified external static pressure of the system. Fan arrangement shall be single or multiple fans as per manufacturer’s standard design. The unit shall operate with noise level not exceeding 65 dB(A) at 1 m free field.Air filtration shall comprise 10-micron washable pre-filters on fresh air side with aluminium/GI frame, and washable pre-filters on exhaust air side, with minimum 90% efficiency down to 10 microns. Instrumentation shall include filter differential pressure switch, and the system shall be provided with wall/duct-mounted CO₂ sensor, integrated with control logic for automatic modulation of fan speed based on CO₂ concentration to ensure demand-controlled ventilation.The unit shall be supplied with a microprocessor-based TFA control panel including start/stop control, fan speed control, alarm indications, and safety interlocks such as fan overload protection and door limit switches. Electrical works shall be suitable for 415 V ±10%, 50 Hz, 3-phase power supply, with FRLS internal wiring, and the unit shall be mounted on neoprene or spring vibration isolators. A stainless steel drain pan shall be provided wherever required.The TFA unit shall be factory performance and functionally tested, and supplied with complete documentation including O&M manuals, wiring diagrams and test certificates. The system shall conform to IS 1391, EN 1886 and AHRI standards, and shall carry a warranty of 12 months from the date of commissioning. Approved makes: Blue Star / Voltas / FläktGroup / Systemair / Trox or equivalent.
438	Vertical In-Line Centrifugal Chilled Water Pump: Supplying, installing, testing and commissioning vertical in-line centrifugal pump suitable for chilled water and/or condenser water circulation, complete in all respects. The pump shall be designed for a duty point of 20 LPS at 30 m head, handling clear water with pH ranging from 6.5 to 8.5. The pump shall be close-coupled or spacer-coupled type, with cast iron casing conforming to IS 210 FG 260, and bronze or stainless steel (AISI 304) dynamically balanced impeller. The pump shaft shall be stainless steel AISI 410/420, with mechanical seal (carbon/ceramic/SS) suitable for continuous operation.The pump shall be fitted with grease-lubricated antifriction bearings and shall achieve a minimum hydraulic efficiency of 70% at the duty point. The pump shall be driven by a TEFC squirrel-cage induction motor, suitably rated approximately 15–18.5 kW, operating at 2900 RPM, suitable for 415 V ±10%, 50 Hz, 3-phase power supply, with IP55 protection and Class-F insulation.
439	The pump-motor assembly shall be provided with flexible coupling complete with coupling guard, suitable for vertical in-line mounting with pipeline-supported arrangement. The unit shall operate with noise level not exceeding 75 dB(A) at 1 m free field, and vibration levels shall comply with ISO 10816. All wetted and non-wetted surfaces shall be finished with epoxy primer and PU top coat suitable for HVAC plant room environments.The pump shall be factory performance tested and hydrostatically tested in accordance with IS 1520 / ISO 5199 standards. The scope shall include all accessories, fasteners, base hardware as required, and 12 months warranty from the date of commissioning. Approved makes: Kirloskar / KSB / Grundfos / Wilo / Ebara or approved equivalent.
440	Chilled water pipes with insulation: Supply, Installation, Testing & Commissioning of Chilled Water Piping with Insulation:Providing, supplying, installing, testing and commissioning chilled water supply and return piping complete with thermal insulation and cladding, suitable for HVAC chilled water systems, in all respects. The piping shall be fabricated from MS ERW or seamless steel pipes, conforming to IS 1239 (Heavy) / IS 3589 standards, with nominal sizes as per hydraulic design. Pipe jointing shall be butt-welded or flanged, with flanges conforming to IS 6392 / ANSI B16.5 Class 150, and all fittings such as MS elbows, tees, and reducers included as required.The piping shall be supported on MS pipe supports with anti-vibration pads, and un-insulated sections shall be painted with two coats of red oxide primer followed by two coats of synthetic enamel. Flow direction arrows and color coding shall be provided on all pipes for easy identification.Thermal insulation shall comprise rigid polyurethane foam (PUF) with density of minimum 40 ±2 kg/m³, thickness of 25 / 40 / 50 mm as specified, and thermal conductivity ≤ 0.024 W/m·K at 10°C. The insulation shall have inherent closed-cell vapor barrier, and be clad with minimum 0.6 mm thick aluminium sheet, stucco embossed, with pop-riveted joints, overlaps, and weather-proof silicon sealant. High-density PUF saddles shall be provided at all supports.The completed piping system shall be hydrostatically pressure tested at 1.5 times working pressure and shall conform to relevant IS / ASTM / ASHRAE standards. The insulation material shall be supplied from approved makes such as Lloyd / Pidilite or equivalent. The system shall be supplied with all accessories, fittings, supports, and workmanship required for proper operation, and shall carry a warranty of 12 months from the date of commissioning.
441	250 mm dia
442	150 mm dia
443	100 mm dia
444	65 mm dia
445	25 mm dia
446	Wafer Type Non-Return Valve (NRV): Supplying, installing, testing and commissioning 150 NB (DN 150) wafer type dual-plate non-return valve (check valve) suitable for chilled water and condenser water HVAC piping systems, complete in all respects. The valve shall be designed and manufactured as per API 594, with wafer-type end connections and face-to-face dimensions in accordance with API 594, suitable for PN 16 pressure rating and operating temperatures up to 120°C.The valve body shall be of cast iron or ductile iron construction, epoxy coated for corrosion resistance. The dual plates/discs shall be stainless steel SS 316, complete with stainless steel spring mechanism for positive and quick closure. The valve shall be provided with metal-to-metal or soft seat, as specified, ensuring zero leakage performance.The NRV shall be suitable for installation in horizontal or vertical pipelines, with flow direction clearly indicated on the body. Each valve shall be hydrostatically and functionally tested at the manufacturer’s works prior to dispatch. The scope shall include all necessary accessories required for proper installation and operation, along with a warranty of 12 months from the date of commissioning. Approved makes: Audco / Zoloto / L&T or approved equivalent.
447	Slim seal Wafer Type Butterfly Valve: Supplying, installing, testing and commissioning wafer type butterfly valve with integrally moulded slim seal, suitable for HVAC chilled water and condenser water services, complete in all respects. The valve shall be designed and manufactured in accordance with API 609 / BS EN 593, with wafer-type end connections, suitable for PN 16 pressure rating and bi-directional installation.The valve body shall be of ductile iron construction, protected with fusion bonded epoxy coating for corrosion resistance. The disc shall be of stainless steel SS 304 or SS 316, and the stem shall be stainless steel, ensuring durability and long service life. The valve shall be provided with an integrally moulded EPDM or NBR slim seal seat, suitable for a temperature range of –10°C to +120°C, and shall ensure bubble-tight shut-off.The valve shall be lever operated, with gear operation optional wherever specified. Each valve shall be tested in accordance with API 598 for pressure and leakage, and shall be suitable for chilled water and condenser water HVAC applications. The scope shall include all accessories required for proper installation and operation, and the valve shall carry a warranty of 12 months from the date of commissioning. Approved makes: Zoloto / Bray / L&T / Audco or approved equivalent.
448	150 mm dia
449	100 mm dia
450	65 mm dia
451	Y-Type Strainer: Supplying, installing, testing and commissioning 150 NB (DN 150) Y-type strainer suitable for chilled water, condenser water and HVAC piping systems, complete in all respects. The strainer shall be designed and manufactured in accordance with BS 736 / ANSI B16.34 / IS 4736, with flanged end connections conforming to IS 1538 / ANSI B16.5 Class 150, suitable for PN 16 working pressure and operating temperatures up to 120°C.The strainer body shall be of cast iron or ductile iron construction, epoxy powder coated for corrosion resistance, and provided with a stainless steel SS 304 perforated screen with 3 mm perforation (or as specified) for effective filtration. The strainer shall be fitted with a bolted cover complete with gasket to facilitate easy cleaning and maintenance, and a drain plug shall be provided for flushing and draining. Flow direction shall be clearly marked on the body.Each strainer shall be hydrostatically pressure tested at the manufacturer’s works, and shall comply with relevant IS/ASTM standards. The scope shall include all fasteners, gaskets and accessories required for proper installation, along with 12 months warranty from the date of commissioning. Approved makes: Zoloto / Leader / Kirloskar or approved equivalent.
452	Forged Brass Ball Valve: Supplying, installing, testing, and commissioning full bore forged brass ball valve suitable for chilled water, hot water, and HVAC piping systems, complete in all respects. The valve shall be designed and manufactured as per IS 15450 / EN 13828 standards, with screwed BSP (F × F) end connections, suitable for PN 16 pressure rating and operating temperatures from 0°C to 120°C.The valve body shall be made of hot forged brass, with a chrome-plated brass ball and brass stem, and PTFE seat ensuring bubble-tight shut-off. The valve shall be quarter-turn operated with lever-type handle of epoxy-coated steel. The valve shall have full bore for unobstructed flow and natural brass or nickel-plated surface finish.Each valve shall be 100% pressure tested at the manufacturer’s works and ISI certified. The supply shall include all necessary accessories, gaskets, and fittings for proper installation and operation. The valve shall carry a minimum warranty of 12 months from the date of commissioning. Approved makes: Zoloto / Leader / Kirloskar / Pegler or approved equivalent.
453	Air Vent: Supplying, installing, testing, and commissioning 25 NB automatic float-operated air vent for air release at high points of chilled or hot water piping systems, complete in all respects. The air vent shall be designed and manufactured as per EN 1074 / manufacturer standard, suitable for PN 10 / PN 16 pressure rating and operating temperatures up to 110°C.The body shall be fabricated from brass with a float made of polypropylene or stainless steel, and the connection shall be screwed BSP. The vent shall allow continuous air discharge via automatic float-controlled mechanism, with isolation valve provided for shut-off. The vent shall provide zero leakage during normal operation and shall be suitable for vertical installation at highest points of piping or AHU coil outlets.The air vent shall have a natural brass finish, be factory pressure tested, and supplied with all necessary accessories required for proper installation. The system shall carry a minimum warranty of 12 months from the date of commissioning. Approved makes: Zoloto / Pegler / Giacomini / Flamco or approved equivalent.
454	Ultrasonic Clamp-On BTU Meter:Supplying, installing, testing and commissioning ultrasonic clamp-on (non-invasive) BTU meter suitable for measurement of thermal energy in chilled water systems, complete in all respects. The BTU meter shall operate on the transit-time ultrasonic principle, with externally mounted clamp-on sensors fixed on the pipe surface, eliminating the need for pipe cutting or system shutdown. The meter shall be suitable for installation on MS, GI, copper, stainless steel and carbon steel pipes, for pipe sizes ranging from DN 25 to DN 600 (or wider as per manufacturer’s standard design), and for clean or treated chilled water applications.The flow measurement shall have an accuracy of ±1.0% of reading or better, and temperature measurement shall be carried out using surface-mounted Class-A Pt100 RTD sensors (3-wire), suitable for 0°C to 120°C, with temperature accuracy of ±0.1°C and minimum measurable differential temperature (ΔT) of 0.3°C. Thermal energy calculation shall be based on measured flow rate, differential temperature and specific heat of water, with energy indication in kWh, MWh and GJ, and flow indication in m³/hr and lpm.The meter shall be provided with a backlit LCD display for real-time indication of instantaneous flow, supply and return temperatures, ΔT and accumulated energy. The system shall include a built-in data logger with minimum 30 days storage capacity, and shall support RS-485 communication with Modbus RTU protocol for BMS integration. Pulse output and/or 4–20 mA output shall be provided, if required.The BTU meter shall conform to EN 1434 / ISO 4064 and CE standards, and the scope shall include testing and commissioning, along with supply of O&M manuals, wiring diagrams and calibration certificates. The system shall carry a minimum warranty of 12 months from the date of commissioning. Approved makes: Siemens / Kamstrup / Danfoss / Endress Hauser or approved equivalent.Note: 100 mm NB pipe size including supply and laying of signal/control cable.
455	Electric Motorized Valve Actuator: Supplying, installing, testing, and commissioning electric motorized actuator of 50mm dia for direct mounting on 3-way or 2-way control valves in chilled water or HVAC systems, complete in all respects. The actuator shall operate on 230 V AC, 50 Hz power supply and provide control signals of 0–10 V DC or 3-point (open-close), with torque suitable for the valve size and stroke time ≤ 120 seconds.The actuator shall be direct-mounted on the valve, provide position feedback, and include manual override for maintenance or emergency operation. Fail-safe position shall be provided as per design (spring return or power-off hold). The unit shall have IP54 or higher protection class, be suitable for ambient temperatures from 0°C to 50°C, and comply with CE electrical safety requirements.The actuator shall be fully compatible with the supplied valve and the actuator-valve assembly shall be factory tested prior to dispatch. The supply shall include all mounting hardware, electrical accessories, and wiring necessary for proper operation and integration with the control system. The actuator shall carry a warranty of 12 months from the date of commissioning. Approved makes: Siemens / Belimo / Honeywell / Danfoss or approved equivalent.
456	Electronic Programmable Thermostat / Controller: Supplying, installing, testing, and commissioning electronic programmable thermostat/controller for return air temperature control of AHUs, complete in all respects. The controller shall accept remote Pt100 RTD sensor input and provide control output of 0–10 V DC or 3-point signal for actuator operation.The unit shall allow temperature set points in the range of 16°C to 30°C, with proportional or PI control mode for accurate temperature regulation. The controller shall have LCD digital display, wall-mounted ABS enclosure, and IP20 protection class, suitable for ambient operating temperatures from 0°C to 50°C. The controller shall operate on 230 V AC power supply, with accuracy of ±0.5°C, and shall comply with CE / IEC standards.The supply shall include all necessary sensors, wiring, and accessories required for proper installation, configuration, and integration with the AHU control system. The unit shall carry a warranty of 12 months from the date of commissioning. Approved makes: Siemens / Honeywell / Schneider or approved equivalent.
457	Temperature Sensor: Supplying, installing, testing, and commissioning Pt100 RTD temperature sensor for return air temperature sensing in AHU systems, complete in all respects. The sensor shall be 3-wire configuration, class A accuracy (±0.15°C at 0°C), and suitable for measuring range 0°C to 50°C.The sensor shall be housed in a robust ABS enclosure and suitable for duct or wall mounting, with a minimum 3 m connection cable for integration with the supplied thermostat/controller. The sensor shall have fast response time, IP54 protection, and be suitable for operating temperatures from –10°C to 60°C. The sensor shall be factory calibrated and fully compatible with the supplied electronic thermostat/controller.The scope shall include all mounting accessories, connection hardware, and wiring for proper installation. The sensor shall carry a warranty of 12 months from the date of commissioning. Approved makes: Siemens / Honeywell / Danfoss / Belimo or approved equivalent.
458	Pressure Gauge: Supplying, installing, testing and commissioning 4-inch (100 mm) dial size Bourdon tube pressure gauge suitable for HVAC chilled water and condenser water applications, complete in all respects. The pressure gauge shall be glycerine-filled for vibration damping and shall conform to EN 837-1 standards.The gauge shall have stainless steel SS 304 case with wetted parts in stainless steel SS 316, suitable for a pressure range of 0–10 bar (or as specified) with accuracy class 1.0. The dial shall be of aluminium with clear black markings, protected by a toughened glass window, ensuring good readability. The gauge shall be suitable for ambient temperatures up to 60°C.The pressure gauge shall be provided with ½” BSP bottom connection, suitable for direct or panel mounting, and shall be factory calibrated with calibration certificate. The scope shall include all accessories required for proper installation and commissioning, along with a warranty of 12 months from the date of commissioning. Approved makes: WIKA / Baumer / H-Guru or approved equivalent.
459	Temperature Gauge: Supplying, installing, testing and commissioning 4-inch (100 mm) dial size bi-metallic temperature gauge suitable for HVAC chilled water and condenser water applications, complete in all respects. The temperature gauge shall be direct reading bi-metallic type, conforming to EN 13190 standards.The gauge shall have stainless steel SS 304 case with stainless steel SS 316 stem, of 150 mm length or as required, suitable for a temperature measuring range of 0°C to 50°C, with accuracy of ±1% of span. The dial shall be of aluminium with clear black scale markings, protected by a toughened glass window, ensuring good visibility.The temperature gauge shall be provided with ½” BSP bottom connection for direct mounting, complete with stainless steel thermowell suitable for the service. Each gauge shall be factory calibrated and supplied with calibration certificate. The scope shall include all accessories required for proper installation and commissioning, along with a warranty of 12 months from the date of commissioning. Approved makes: WIKA / Winters / Baumer or approved equivalent.
460	Air Distribution Ducts: Supplying, installing, testing and commissioning Galvanized Iron (GI) air distribution ducts for HVAC systems, complete in all respects. The ducts shall be fabricated from GI sheets conforming to IS 277 / ASTM A653, with minimum zinc coating of 120 GSM, in rectangular or circular profiles as per design. Sheet thickness shall be as per SMACNA standards, and all ducts shall be factory-fabricated and machine folded for accuracy and rigidity.All duct joints shall be flanged with gasket, using GI or MS TDC / angle flanges, and sealed with approved sealant to ensure airtightness. Ducts shall include stiffeners as per SMACNA guidelines, and shall be supported on GI or MS hangers with rubber pads to minimize vibration and noise. The duct leakage class shall be SMACNA Class-3, and access doors shall be provided at required locations for inspection and maintenance. GI volume control dampers shall be installed where specified for air balancing.The ducts shall be supplied with GI finish (painting not required) and shall be tested for air leakage and airflow balancing. All fabrication and installation shall conform to SMACNA / DW-144 standards, and the system shall carry a warranty of 12 months from the date of commissioning.
461	18 Gauge
462	20 Gauge
463	22 Gauge
464	Nitrile Rubber (NBR) Foam Insulation: Supplying, installing, and commissioning closed-cell Nitrile Rubber (NBR) foam insulation for GI ducts and chilled water piping, complete in all respects. The insulation shall have a thickness of 9 mm and a density of 40–60 kg/m³, with thermal conductivity ≤ 0.034 W/m·K at 0°C. The insulation shall provide a water vapour permeability of ≤ 7.0 × 10⁻¹² kg/m·s·Pa and shall comply with Class-0 / Class-1 fire rating standards.The insulation shall be bonded using manufacturer-recommended adhesive and shall be clad with aluminium foil (0.13 mm) or sheet (0.4 mm) for mechanical protection. Joints shall be sealed with aluminium tape to ensure vapor-tight continuity. The insulation shall be suitable for operating temperatures from –50°C to +105°C, finished to a smooth and neat appearance.All materials and installation shall conform to relevant ASTM and BS standards. The scope shall include all accessories, adhesives, tapes, and workmanship required for proper application and durability. The insulation system shall carry a warranty of 12 months from the date of commissioning. Approved makes: Armacell / K-Flex / Aerofoam or approved equivalent.
465	Acoustic Insulation for Ducts: Supplying, installing, and commissioning open-cell acoustic foam for ducts, and acoustic lining, complete in all respects. The insulation shall have a thickness of 25 mm with a density of 24–32 kg/m³, and Noise Reduction Coefficient (NRC) ≥ 0.75 for effective sound attenuation.The insulation shall be faced with black tissue or perforated aluminium for durability and aesthetic finish, and shall be treated for moisture and fungal resistance. Fixing shall be carried out using suitable adhesive along with GI pins, and all edges shall be properly sealed to ensure continuity and performance. The insulation shall be suitable for operating temperatures up to 120°C and shall comply with IS 8183 / ASTM C423 standards.The scope shall include all accessories, adhesives, fasteners, and workmanship required for proper installation. The acoustic insulation system shall carry a warranty of 12 months from the date of commissioning. Approved makes: Saint-Gobain / Twiga / Rockwool or approved equivalent.
466	Volume Control Dampers: Supplying, installation, testing of Volume Control Dampers made out of 16 SWG GI sheet material, adjustable type opposed blade with necessary flanges for duct branches connecting to main plenum and supply air branch ducts etc. and ball socketed type connecting rod between blades, PVC gears for smooth operation and suitable sturdy handle with OPEN/CLOSE position indicator.
467	Fire Dampers GI: Supply & installation of Fire dampers along with necessary fitting and accessories and as per tender specifications.
468	Return Air Grille: Supplying, installing, testing, and commissioning zero-deflection continuous return air grille for return or exhaust air applications in HVAC systems, complete in all respects. The grille shall be fabricated from extruded aluminium with fixed 0° deflection blades in a continuous linear configuration, with length as per architectural requirements. Blades shall have uniform spacing to ensure high free area ratio, minimal pressure drop, and noise level not exceeding NC 25.The grille shall be powder-coated with colour as specified by the Architect / EIC, and shall be suitable for wall or ceiling mounting. Where required, a GI plenum box with 13 mm nitrile rubber insulation shall be provided. The grille shall include a removable core for cleaning and shall have neat, flush edge finish.The supply and installation shall conform to IS / ASHRAE standards. The complete scope shall include all necessary accessories, fasteners, and installation hardware, with a warranty of 12 months from the date of commissioning. Approved makes: Caryaire / Halton / TROX / Systemair or approved equivalent.
469	Swirl Type / Jet nozzle Ceiling Air Diffuser: Supplying, installing, testing, and commissioning swirl /jet nozzle type ceiling air diffuser for supply air distribution in HVAC systems, complete in all respects. The diffuser shall be of 600 × 600 mm size, suitable for standard false ceiling grid, fabricated from high-grade aluminium with fixed or removable swirl face pattern to ensure horizontal swirl air pattern with high induction (in case of swirl type diffuser).The diffuser shall be designed for low to high airflow volumes with minimal pressure drop and noise level not exceeding NC 30. The unit shall be powder-coated, finished in white (RAL 9016) or as specified, and provided as lay-in type for false ceiling installation.Each diffuser shall be supplied with a GI plenum box fitted with volume control damper, and the plenum shall be insulated with 13 mm or 25 mm nitrile rubber as per design requirements. Neck size shall be as per duct design, and the core shall be easily removable for maintenance and cleaning.The diffusers shall conform to IS / ASHRAE standards and be supplied with all necessary mounting accessories, fasteners, and installation hardware. The complete system shall carry a warranty of 12 months from the date of commissioning. Approved makes: Caryaire / Systemair / TROX / Kruger or approved equivalent.
470	Field insulation: In-situ PUF insulation which includes supply of Polyol &Isocynate chemicals and 24G Aluminum sheet of required quantity for field PUF insulation of joints and valves. It includesaluminum sheet fabrication, making mould over part to be insulated, mixing & pouring of chemicals into the aluminum mould.
471	Supply, fabrication and erection of 24 G Aluminium sheet
472	Supply and pouring of Polyol chemical
473	Supply and pouring of Isocynate chemical
474	Supply, installation, testing and commissioning of high wall Inverter cassette air conditioners operating on energy efficient rotary compressor of nominal cooling capacity 2.0 TR comprising of indoor unit , outdoor unit and copper tubes with thermal insulation shall confirm to 5 star with IS energy efficiency ratio conforming to IS 1391 part - 2 and meet the following technical specification and scope of work. Power supply: Single phase ,230V, 50Hz . Compressor type: rotary, Refrigerant: R32, Condenser coil: Air cooled internally cross hatched copper tubes with anti-corrosive fin condenser, Evaporator : Copper tube, hydrophilic anti corrosive coated fins, Fan speed : 4 steps (Low, Medium, High and Auto), Remote control : Wireless LCD shall be available with the equipment all as per the specification and as directed by Engineer in Charge.NOTE : 1. The warranty of unit should be one year from date of installation at site. 2. The compressor warranty should be five years from the date of installation at site.3. The copper tube and cable necessary for erection of AC unit shall be paid under relevant item. Preferred make: Hitachi, Voltas, Bluestar, Panasonic
475	Supply and fixing of heavy duty split AC outdoor mounting stand bracket made of 2.0 mm thick heavy duty Galvanized steel with two coat of powder coating of off white colour with load carrying capacity up to 100 Kg with suitable fasteners all as directed by Engineer in Charge.
476	Supply of soft drawn bright annealed seamless copper tube for 2.0 TR split AC unit as per ASTM B 68-02 both suction and liquid line measured together with wall thickness suitable for R32 and thermal insulation should be flexible closed cell elastomeric nitrle rubber foam tubes, class \\"O\\" with 9 mm thickness to suit above copper tubes along with white tape insulation all enclosed in a PVC slim duct and fittings of heavy duty of suitable size all as per the specification and as directed by Engineer in Charge.Preferred make Camipro, uniflow or equivalent.
477	Supply of 4 core 2.5 Sq.mm FR-LSH insualted, 1100V, multi strand flexible copper conductor cable shall confirm to IS 694.Preferred make for cable:Powerflex, Havels, Finolex or equivalent.
478	Supply of 3 core 2.5 Sq.mm FR-LSH insualted, 1100V, multi strand flexible copper conductor cable shall confirm to IS 694 along with suitable cable casing cap.Preferred make for cable:Powerflex, Havels, Finolex or equivalent.
479	Supply and fixing of heavy duty 1” diameter PVC drain pipes and fittings includes bends, T connections, couplings and U clamps, ets., for fixing of drain line from IDU of split ac up to ground level. It includes U trap for proper drain of air conditioners condensate water without seepage. The U clamp should be installed at an interval of 1.5 m with slop for drain of water all as per the specification and as directed by Engineer in Charge.
480	Supply and fixing of 300mm wide GI tray and Supports for copper piping and cabling: Use factory fabricated 2mm thick GI tray of following sizes with G.I cover, GI angles, clamps , Threaded rod (8mm) and fasteners etc., for clamping the copper pipes and cables . The GI support angles shall be grouted to the wall and roof structure using anchor fasteners. The maximum spacing between the supports shall not exceed 1200-mm. The copper piping and cable shall be completely covered with factory fabricated GI tray, etc., complete as per specification and as directed by Engineer - In- Charge.
481	Supply, Installation, Testing and Commissioning of 4 Loop modular Analog Addressable, TCP/IP based, wall mountable Fire Alarm Control Panel (FACP) with Built-in Battery backup of loop length 2500 mtr length.. The FACP shall be Vds Approved as per EN54, all complete as per specification.
482	Supply, Installation, Testing and Commissioning of Intelligent Addressable multi criteria detectors with Base with built-in short Circuit isolator all as per EN 54-29, Vds Approved, etc., all complete as per specification
483	Supply, Installation, Testing and Commissioning of Intelligent Addressable Loop / Panel Powered Sounder with In built Isolatorall complete as per specification
484	Supply, Installation, Testing and Commissioning of Intelligent Addressable Loop / Panel Powered Flasher with In built Isolator all complete as per specification .
485	Supply, Installation, Testing and Commissioning of Indoor Type Single Action Intelligent Addressable Manual Call Point with built in isolator; Vds Approved as per EN-54, etc., all complete as per specification.
486	Supply, Installation, Testing and Commissioning of Response Indicator to reflect the detection signal of detectors inside the enclosures/ above false ceiling, etc., all complete as per specification
487	Supply and Fixing of ( 100 MM * 100 MM) Detector back box.
488	Supply and Installation of 20 MM GI Conduit along with necessary Solid Base ,Clamp,bend ,coupling and other Related accessories for installation; all complete as per specification
489	Supply and Laying of 2C x 1.5 sq.mm, twisted pair, unarmoured, shielded, flexible, ISI approved, FRLS cable compliance to IS694:1990, etc., all complete as per specification
490	Supply & Installation of 1 ½\\" (40 mm) casing and capping (PVC trunking) with accessories like JBs, Coupling, External & Internal Bends, Elbows and end cap. Casing and capping shall be of good quality PVC, free from defects like deformations, unevenness, blisters, cavities, etc., all complete as per specification
491	Supply and Laying of 3C * 2.5 sqmm Unarmoured twisted pair Cable.
492	Supply and Installation of 10 A 2 pole MCB.
493	Supply and external installation of sizes of GI Flexible Hose as per the detailed specification.
494	Erection, Installation and Dismantling of Scaffold platform for height up to 9 m for erection of Beam Detector
495	Supply and Fixing of the Surface mount Control Module to integrate with the Linear Smoke Detector.
496	Supply and Fixing of the Conventional Motorized 50 mtr range of Beam Detector. along with Reflectors with proper alignment and configuration. Government of IndiaDepartment of Atomic EnergyGeneral Services OrganizationCivil Engineering Group TENDER DOCUMENT FOR Name of Work: Construction of Convention center building in Anupuram Township. Tender Notice No. : GSO/CTC/CEG/331/2026 Part – II : Financial Bid (Section - VIII) INDEX S/No. Title Page No.
497	i) Part - A : Civil Works 62 Pages ii) Part - B : Electrical Works, Internal Intercom Telephone System and Network system & CCTV 44 Pages iii) Part - C : AC Works, Fire Alarm System and Fire Fighting System 24 Pages GENERAL INFORMATION FOR GUIDANCE OF TENDERERS
498	The schedule of quantities is to be read for the purpose of pricing in conjunction with the special conditions, general rules for the guidance of contractors, conditions of contract, specifications, drawings, schedule of supply of materials and the appendices.
499	The prices inserted in the schedule of quantities shall be inclusive of value of the work described including all cost and expenses, which may be required in and for the construction of the work described together with the general risks, liabilities and obligations not forth or implied in the documents on which the tender is to be based.
500	The quantities stated are to be considered approximate only and the unit prices entered in the schedule of quantities and prices shall apply only to the actual quantities measured in the completed work in accordance with the specifications.

Tender Documents

SR No	FileName	File Description
1	Click here to download tender document	Tender Documents
2	Click here to download tender document	Tender Documents
3	Click here to download tender document	Tender Documents
4	Click here to download tender document	Tender Documents
5	Click here to download tender document	Tender Documents
6	Click here to download tender document	Tender Documents
7	Click here to download tender document	Tender Documents
8	Click here to download tender document	Tender Documents
9	Click here to download tender document	Tender Documents
10	Click here to download tender document	Tender Documents
11	Click here to download tender document	Tender Documents

Also Visit

Tenders

Tamil Nadu Tenders

Construction Tenders

Building Construction Tenders

Building Work Tenders

Disclaimer

We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.

Top

Tender For Construction Of Convention Center Building In Anupuram Township., Chengalpattu-Tamil Nadu

Tender Documents

Disclaimer

About Us

Services

Browse Tenders

For Sales Inquiry

Tender For Construction Of Convention Center Building In Anupuram Township., Chengalpattu-Tamil Nadu

Tender Documents

Disclaimer

OTP Verification

About Us

Services

Browse Tenders

For Sales Inquiry

Connect With Us