|
| 1 | Civil Works |
| 2 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil. |
| 3 | Filling available excavated earth (excluding rock) in trenches, plinth. sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and for all lift |
| 4 | Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. |
| 5 | P/L in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 6 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. |
| 7 | P/L in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size de rived from natural sources) |
| 8 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fllets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement: 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 9 | Reinforced cement concrete work in beams, suspended foors, roofs having slope up to 15* landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to foor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources: 3 graded stone aggregate 20 mm nominal size derived from natural sources). |
| 10 | Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete. |
| 11 | Centering and shuttering including strutting, propping etc. and removal of form for Suspended floors, roofs, landings, balconies and access platform |
| 12 | Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers |
| 13 | Centering and shuttering including strutting, propping etc. and removal of form for Columns, Pillars, Piers, Abutments, Posts and Struts |
| 14 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 15 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 16 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 17 | P/F Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 18 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). Second class teak wood |
| 19 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 20 | P/F aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing I paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portion Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron) |
| 21 | P/F glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm) |
| 22 | Providing & Fixing LM 01750 8 ft x 4 ft Suede Finish Decorative Laminate - 1 mm including cost of adhesive of approved quality all complete as per direction of Engineer-in-Charge. (Based on DAR 12, It-9.127.2)\\" |
| 23 | Providing and fixing ISI marked premium quality solid core flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 19 mm thick (for cupboard) including ISI marked nickel plated bright finished M.S. piano hinges with necessary screws (As per DAR NO. 9.21.3) |
| 24 | P/F factory made uPVC door frame made of uPVC extruded sections having an overall dimension as below (tolerance ±1mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame to be Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer’s specification and direction of Engineer-in-charge Extruded section profile size 42x50 mm |
| 25 | P/F to existing door frames. 24 mm thick factory made PVC door shutters made of styles and rails of a uPVC hollow section of size 59x24 mm and wall thickness 2 mm (± 0.2 mm) with inbuilt edging on both sides. The styles and rails mitred and joint at the corners by means of M.S. galvanised/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 20x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of 'H' section, a uPVC hollow section of size 100x24 mm and 2 mm (± 0.2 mm) wall thickness, fixed to the shutter styles by means of plastic/galvanised M.S. 'U' cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer's specification and direction of Engineer-in-charge. (For W.C. and bathroom door shutter). |
| 26 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works |
| 27 | P/L Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed vitrified floor tiles polished finish of size Size of Tile 600 x 1200 mm |
| 28 | P/F on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110 mm diameter |
| 29 | P/F tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main \\"T\\" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross \\"T\\" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main \\"T\\" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross \\"T\\" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main \\"T\\" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. GI Metal Ceiling Lay in plain Tegular edge Global white color tiles of size 595x595 mm, and 0.5 mm thick with 8 mm drop; made of G I sheet having galvanizing of 100 gms/sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending. |
| 30 | 12 mm cement plaster of mix : 1:6 (1 cement: 6 fine sand) |
| 31 | 6 mm cement plaster of mix : 1:3 (1 cement : 3 fine sand) |
| 32 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water thinnable priming coat with cement primer |
| 33 | Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm |
| 34 | P/F Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall 20 mm nominal dia Pipes |
| 35 | P/F Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall 25 mm nominal dia Pipes |
| 36 | P/F gun metal gate valve with C.I. wheel of approved quality (screwed end) : 25 mm nominal bore |
| 37 | P/F gun metal gate valve with C.I. wheel of approved quality (screwed end) : 20 mm nominal bore |
| 38 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 39 | Providing and fixing C.P. brass bib cock two way of approved quality : 15 mm nominal bore OPP-CHR-15041PM (18.49.1) |
| 40 | Providing fixing Waste Coupling 32mm Size Full Thread with 80mm Heightof Model No ALD-CHR-705 of Jaquar or of equivalent design of Hindware/Parrywar/Roca/Prayag etc per the instruction of engineer in charge |
| 41 | Providing and fixing GLORIA 240 mm Door Handle Set 2C with victor cylinder 24cm (240mm) Satin Steel of Godrej 3124 or equivalent brand of all complete as per direction of Engineer-in-Charge. (Based on DAR 2012, It-21.13) |
| 42 | Providing and fixing hydraulic Door closer-(rectangular Type)(CE Certified 40-80 kg) all complete of Godrej 7880 or equivalent brand as per direction of Engineer-in-Charge.\\". |
| 43 | Providing and fixing Havells or equivalent make exhaust fan all complete as per direction of Engg-in-Charge. |
| 44 | Providing fixing Round ShapeMaze Overhead Shower - Chrome And Shower Arm 20mm dia. & 600mm Long Round Shape with 90˚ Bend for Wall Mounted Showers with Flange of Model No -OHS-CHR1633 KPM & SHA-CHR479L600 of Jaquar or of equivalent design of Hindware/Parrywar/Roca/Prayag etc per the instruction of engineer in charge |
| 45 | Providing fixing single piece water closet of Model No-LYS-WHT-38851S300UFSMSNR.of Jaquar or of equivalent design of Hindware/Parrywar/Roca/Prayag etc. as per the instruction of engineer in charge |
| 46 | Providing and fixing Water Geyser EPM-WHT-V006, TankCapacity - 6 Litres as per direction of Engineer-in-charge. |
| 47 | Providing and fixing C.P. brass Health faucet of approved quality. ALD-CHR-573 |
| 48 | Providing fixing Hand Shower 180mm Round Shape Single Flow (ABS Body Chrome Plated with Gray Face Plate) of Model No -HSH-CHR-1781 of Jaquar or of equivalent design of Hindware/Parrywar/Roca/Prayag etc per the instruction of engineer in charge |
| 49 | Providing and fixing 50.8 cm x 101.6 cm capsule framed mirror K-26051IN-BGL all complete as per direction of Engineer-in-Charge |
| 50 | Providing and fixing chromium plated brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete. |
| 51 | Supplying and fixing One Stainless steel S304 grade Pull handle - H-Type (25 mmdiaX400mm) 'all complete as per the direction of EIC. ( It-21.13)\\" |
| 52 | Providing fixing Pillar Cock Auto Closing System with 65mm Extension Body of Model No -PRS-CHR-031L65 of Jaquar or of equivalent design of Hindware/Parrywar/Roca/Prayag etc per the instruction of engineer in charge |
| 53 | Providing and fixing Toilet paper Holder Recessed Type of approved quality AHS-CHR-1551 |
| 54 | Providing and fixing Designer Tower bolt 30cm (300mm) (12), (Rod Thickness 10mm (1cm) all complete as per direction of Engineer-in-Charge. Of Godrej 2734 or equivalent brand (Based on DAR : 9.97.2) |
| 55 | Providing fixing Towel Rack 600 mm long with lower hangers of Model No --AKP-CHR-35781PS of Jaquar or of equivalent design of Hindware/Parrywar/Roca/Prayag etc. with fixing accessories per the instruction of engineer in charge |
| 56 | Providing fixing urinal of Model No-URS-WHT-13253N and Auto closing concealed Urinal flush valve of Model No-PRS-CHR-073.of Jaquar or of equivalent design of indware/Parrywar/Roca/Prayag etc. with fixing accessories per the instruction of engineer in charge |
| 57 | Providing Wash Basin with pillar cock, soap dispenser, tumbler holder of jaquar make (ALS-WHT-85601 , Counter Top Basin, pillar cock ( KUP-35001PM) with base flange, Soap Dispenser - ( ACN-1135N), Tumbler holder (AKP-35741P)) |
| 58 | Providing fixing Single Lever Concealed Manual Shower Valve - Chrome and Concealed Body for Single Lever High Flow Diverter with Button Assembly, and Exposed Parts of Model No -OPP-CHR-15227KPM & ALD-CHR-079N of Jaquar or of equivalent design of Hindware/Parrywar/Roca/Prayag etc. with fixing accessories per the instruction of engineer in charge |
| 59 | Providing and fixing Soap Dispenser with Glass Bottle ACN-1135N |
| 60 | Providing and fixing SS Aldrop 1.6x25cm (16x250mm) Godrej 2282 or equivalent brand of all complete as per direction of Engineer-in-Charge (Based on DAR:B261 9.96.2).\\" |
| 61 | Construction of septic tank for 10 users with 1st class brick work in cement mortar (1:6) including two 560 mm dia. RCC manhole cover(heavy type)of approved make supplied, fitted and fixed in the 100mm thick RCC (1:2:4) top slab with necessary fittings, 20mm thick cement plaster with neat cement finish to the internal surfaces and 12 mm thick cement plaster to outside wall & 100 mm thick RCC(1:1.5:3) bottom slab including supplying, fitting and fixing all necessry specials, fittings, tees, foot rest etc. & including constructing attached inspection pit and connecting all necessary pipes, joints etc. Finished level of Septic Tank should be 400 mm. from GL, Ventilation pipe & Mosquito proof mesh, should be follwed as per IS:2470 Part-I. |
| 62 | Electrical Works |
| 63 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FR PVC insulated copper conductor single core cable etc as required. |
| 64 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FR PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire |
| 65 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FR PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire |
| 66 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FR PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required 2 X 4 sq. mm + 1 X 4 sq. mm earth wire |
| 67 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.5/6 amps switch |
| 68 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 15/16 amps switch |
| 69 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 3 pin 5/6 amp socket outlet |
| 70 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 6 pin 15/16 amp socket outlet |
| 71 | Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required 20mm |
| 72 | Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, , “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required single pole |
| 73 | Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 100amp |
| 74 | Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required. 1 or 2 Module (75mmX75mm) |
| 75 | Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required. 3 Module (100mmX75mm) |
| 76 | Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required. 6 Module (200mmX75mm) |
| 77 | Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required. 8 Module (200mmX75mm) |
| 78 | Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required. (COST FOR EACH) |
| 79 | Supplying and fixing stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required. |
| 80 | Supplying and fixing PVC batten/ angle holder including connection etc. as required |
| 81 | Supplying and fixing 3 pin, 5 amp ceiling rose on the existing junction box/ wooden block including connection etc as required |
| 82 | Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required.(Upto 450 mm sweep) |
| 83 | Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required. |
| 84 | Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 6 way, Double door |
| 85 | Providing & fixing of 12watt (3000K-5000K)LED square/round panel light complete set recess/surface mounted complete set as per instruction of EIC |
| 86 | Supply & fixing of new wall mounting fan 400 mm of approved make ISI marked as per instruction of EIC(Make Bajaj, Crompton, Havells etc. or equivalent) |
| 87 | Supply of 3 pin top 15/16 Amp. ISI marked of approved make as per instruction of EIC |
| 88 | Supply of exhaust fan 4/5 blade 200 mm single phase of approved make ISI marked as per instruction of EIC(Make Bajaj, Crompton, Havells etc. or equivalent) |
| 89 | Supply of new LED tube light set complete of approved make in all respect 20 watt as per instruction of EIC. |
| 90 | Providing & fixing of 36watt (3000K-5000K)LED square panel light complete set recess/surface mounted complete set as per instruction of EIC |
| 91 | Providing power unit complete set with plate, 25 A starter, socket, plug |
| 92 | Supplying of 10sq.mm 2 Core, unarmoured Aluminium cable of approved make as per instruction of EIC |
| 93 | Total impact of GST for the purpose of CTC Please Enable Macros to View BoQ information |
