|
| 1 | Excavation by Mannual/ Mechanical Means, in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material up to a distance of 50 m beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift upto 1.5 m.) |
| 2 | Excavation by Mannual / Mechanical Means, in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material up to a distance of 50 m beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift from 1.5m to 3.0m) |
| 3 | Removal and carriage of surplus excavated material and debris (desmantled brickwork, concrete, tiles, plaster etc) to the disposal point as directed by EIC, anywhere in the factory, within 3 km. |
| 4 | Providing dry/ trap/ granite/ quartzite/ gneiss rubble stone soling 15 cm to 20 cm thick including hand packing and compacting etc. complete. |
| 5 | Providing and laying Cast in situ/Ready Mix cement concrete in M-10 of trap/ granite/ quartzite/ gneiss metal for foundation and bedding including bailing out water, centering, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing if required and curing complete. |
| 6 | Providing and laying Cast in situ/Ready Mix cement concrete in M-20 of trap/ granite/ quartzite/ gneiss metal for floor and foundation and bedding including bailing out water, centering, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing if required and curing complete. |
| 7 | Providing and laying reinforced cement concrete of grade M 25 (using 20 mm, nominal gauge graded stone aggregate) machine/manual mixed and mechanically vibrated and finished to a fair face including the cost of centering, shuttering but excluding the cost reinforcement steel etc. complete. |
| 8 | Supply, cut, bend and fix in position TMT Fe- 500 bars for all diameters confirming to is 1786, including tying with binding wire (16 swg annealed wire) or welding, steel reinforcement for all reinforced concrete at all locations and levels, including transporting, handling etc. complete. |
| 9 | Dismantling brick masonry in lime or cement mortar and stacking the materils as directed with all leads, lifts etc. |
| 10 | Removing cement concrete / RCC (including plaster if any over concrete /RCC ) including stacking the spoils as directed with all leads, lifts etc, complete. |
| 11 | Removing cement tiles, or any tiles, marble or polished shahabad floor or dado without bed concrete including stacking the materials as directed with all leads, lifts etc. complete |
| 12 | Removing plaster including disposing of the spoils as directed with all leads, lifts etc, complete. |
| 13 | Removing earthen, stonewate pipe, cast iron or wrought iron or A.C. and stacking them as directed with all leads, lifts etc. complete. |
| 14 | Removing urinal pans or wash hand basins with frame including disconnecting the sanitary and water supply connections, removing the same carefully and stacking the serviceable materials as and where directed including throwing the unserviceable materials outside etc complete |
| 15 | Removing W.C. pans including disconnecting the sanitary and water supply connections, removing and breaking flooring and bed con-crete around pan removing the same carefully and stacking the serviceable materials as adn where directed including throwing the unserviceable materiasls out side etc. carefully and throwing out the refusal outside etc. complete. |
| 16 | Removing ventilator, doors and windows with frame and stacking thematerialswithallleads, lifts etc. complete. |
| 17 | Removal of plants / ficus grown by pulling out root system embedded in masnory, cutting stem and application of high/gur/lime formulation as specified by the Architect or other patented chemical biocide treatment such as biocide 'Glycel' (iso proplamine salt of glyphosate) or other chemical as specified by the Engineer in charge etc. complete. |
| 18 | Providing second class Burnt Brick masonry with conventional/ I.S. type bricks in cement mortar 1:6 in foundations/ Superstructure and plinth of inner walls/ in plinth external walls including bailing out water manually , striking joints on unexposed faces, raking out joints on exposed faces and watering etc. Complete. |
| 19 | Providing internal / External cement plaster 12 mm thick in single coat in cement mortar 1:4 without neeru finish to concrete or brick surfaces, in all positions including scaffolding and curing etc. complete. |
| 20 | Providing internal / External cement plaster 20 mm thick in Single coats in cement mortar 1:4 without neeru finish, to concrete, brick surface, in all positions including scaffolding and curing etc.complete. |
| 21 | Providing internal / external 12 mm thick Ready Mix plaster confirming to IS:4031(Part-4) 1988 and IS 383-1970 in a single coat using Cement mortar of proportion 1:4 containing special type of polymer additives about 0.4%, to all type of surfaces in all positions including scaffolding and curing complete. |
| 22 | Providing internal / external 20 mm thick Ready Mix plaster confirming to IS:4031(Part-4) 1988 and IS 383-1970 in a single coat using Cement mortar of proportion 1:4 containing special type of polymer additives about 0.4%, to all type of surfaces in all positions including scaffolding and curing complete |
| 23 | Providing and laying vitrified mirror / glossy finish tiles having size 590 mm to 605 mm x 590 mm to 605 mm of 8 to 10 mm thickness and confirming to IS. 15622-2006 ( group Bla) of approved make (make-Kajaria/Somany/Nitco/ Johnson or equivalent), shade and pattern for dado and skirting in required position fixed in 1:4 cement mortar including neat cement float, filling joints, curing and clearing etc. complete |
| 24 | Providing and laying 10 to 13mm thk. heavy duty, scratch resistant, high abrasion resistant vitrified tiles (Durastone or equivalent) conforming to I.S.15622 with special hard wearing layer and water absorbtion less than 0.08% for flooring of an approved, quality, make, pattern and size for flooring including cement mortar bedding of 25 mm thick in 1:4 proportion, cutting, leveling, jointing, filling the joints by neat cement slurry or approved colour grout, curing, finishing etc complete as directed by RCF. |
| 25 | Providing and applying one coat of primer of approved manufacture and shed including scaffolding preparing the surface by cleaning dirt and other foreign matters, scrapping if necessary including scaffolding etc. complete. |
| 26 | Providing and applying washable oil-bound distemper of approved colour and shade to old and new surfaces in two coats including scaffolding, preparing the surfaces. (excluding the primer coat.) etc. complete. |
| 27 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Flat back wash basin size 630x450 mm with single 15 mm C.P. brass pillar tap (Parryware / Hindware / Cera / Somany or equivalent) |
| 28 | Providing and fixing on walls/ ceiling/ floor 15 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line as directed etc. complete. |
| 29 | Providing and fixing on walls/ceiling/floor 20 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including as directed etc. complete. |
| 30 | Providing and fixing on walls/ ceiling/ floor 25 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete as directed etc. complete. |
| 31 | Providing and fixing 75 mm dia stabiliser pipe/ P.V.C. soil vent/waste pipe and with necessary fixtures and fitting such as bends, tees, single junctions, slotted vent, clamps etc. complete |
| 32 | Providing and fixing 100 mm dia stabiliser pipe/ P.V.C. soil vent/waste pipe and with necessary fixtures and fitting such as bends, tees, single junctions, slotted vent, clamps etc. complete. |
| 33 | Providing and fixing 10 cm PVC nahani trap with grating etc. complete. |
| 34 | Providing and fixing anodized (anodic film must not be less than 15 microns i.e. AC-15) aluminum fixed/ sliding / pivoted / top hung / side hung / louvered type windows, doors, ventilators and partitions conforming to IS:1948, 1961 with hollow bottom section & standard single / two / three / four track frame section all round (top, bottom and sides) with shutter frame made up of standard handle section standard interlocking section and standard top and bottom section with infill panel of plain / frosted / tinted glass/ Novapan sheet / acrylic sheet / hardner laminated sheet as listed below with nylon guides, gliders glass fixing PVC weather strips, neoprene gasket, PVC weep holes etc complete with approved type of locking arrangement, handles and other fixtures including fixing, filling the gaps with silicon sealant, cleaning polishing the aluminium section with petrol and / or other agents as specified by the manufacturers etc. complete as directed .Aluminium Section used for |
| 35 | Providing and Fixing 4 mm thick Plain / frosted / tinted Glass along with tools tackles |
| 36 | Providing and fixing all sides polished natural stone as specified below of approved quality, pattern, colour and thickness for door and window frames / architraves including preparing the surface and levelling in the desired line, machine cutting, jointing in approved adhesives, leveling, smooth cement plastering along the sides to match the existing surface in cement mortar, filling the joints with pigment mixed with cement, cleaning, finishing, curing etc complete as directed by Engineer In Charge.With Kadappa stone 25-30MM Thickness and 150 MM Width. |
| 37 | (Providing and erecting Structural Steel Shed over Toliet block Terrace and For Providing and Fixing Strutural Steel Doors (Shutters & frames) at Toilets and Welfare:- Providing and fabricating structural steel work in rolled sections like joists, channels,angles, tees etc. as per detailed design and drawings or as directed including cutting, fabricating, hoisting, erecting, fixing in position making riveted / bolted /welded connections without connecting plates, braces etc. and including painting with anti corrosive epoxy paint ( one primer and over it two coats) of approved quality and shade, including preparing the surfce by mechanical buffing etc.complete. |
| 38 | Providing and fixing 0.6 to 0.7 mm thick plain galvanised iron sheets on Doors made of structural steel sections, fixing by means of nut and bolts or self tapping screws or as directed by RCF etc. including one coat of primer anf two coats of synthetica enamel paint complete. |
| 39 | Fabricating structural steel work in rolled sections like joists, channels,angles, tees etc. as per detailed design and drawings or as directed including cutting, fabricating, hoisting, erecting, fixing in position making riveted / bolted /welded connections without connecting plates, braces etc. and including painting with anti corrosive epoxy paint ( one primer and over it two coats) of approved quality and shade, including preparing the surfce by mechanical buffing etc.complete.(Structural steel , Paint and Primner will be provided by RCF inside Factory premises / stores . Shifting material by getting issue note etc to site is cotractors scope. All consumables (like welding rod, Gas etc ) are in contractors scope. |
| 40 | Providing and fixing colour coated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (base metal of minimum of 0.45mm with total coating thickness of 0.05mm) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer and polyester top coat 15-18 microns, on both side of the sheet. Sheet should have protective guard film to avoid scratches during transportation and should be supplied in single length upto 12 metre or as directed by Engineer in-charge. The sheet shall be fixed using Zinc-Tin alloy coated, self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. |
| 41 | Providing and fixing white vitreous china pedestal type (European type/wash down type) water closet pan. of size 580*440 mm (Cera, Hindware. Parryware or equivalent) |
| 42 | Providing and fixing solid plastic seat with lid for pedestal type W.C. pan complete White solid plastic seat with lid (Cera, Hindware. Parryware or equivalent) |
| 43 | Providing and fixing white vitreous china water closet squatting pan (Indian type) : Orissa pattern W.C. pan ( including foot rests) of size 580x440 mm (Cera, Hindware. Parryware or equivalent) |
| 44 | Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge. (Cera, Hindware. Parryware or equivalent) |
| 45 | Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete. 10 litre capacity - White (Cera, Hindware. Parryware or equivalent) |
| 46 | Providing and fixing white vitreous china flat back type lipped front urinal basin of 430x260x350 mm sizes (Cera, Hindware. Parryware or equivalent) |
| 47 | (Urinal Partition)-Providing and fixing partition with kadappa stone of all sizes and 25 mm thick polished on both side and edges to original including fixing in position in cement mortor 1:4 curing polish- ing, cleaning etc complete. |
| 48 | Providing and fixing PTMT 15 mm Urinal spreader size 95x69x100 mm with 1/2” BSP thread and shapes, weighing not less than 60 gms. |
| 49 | Providing and fixing PTMT urinal cock of approved quality and colour. 15 mm nominal bore, 80 mm long, 42 mm high and 30 mm wide with BSP female threads weighing not less than 48 gms (Cera, Hindware. Parryware or equivalent) |
| 50 | (Making Seating arrangements at Welfare or any job at any other location instructed by RCF) Providing and fixing 25 mm to 30 mm thick one side polished black kadappa stone slab of approved quality including giving required size and shape etc. Fixing in cement mortar 1:3 curing and cement etc. complete. Please Enable Macros to View BoQ information |
| 51 | (Making Seating arrangements at Welfare or any job at any other location instructed by RCF) Providing and fixing 25 mm to 30 mm thick one side polished black kadappa stone slab of approved quality including giving required size and shape etc. Fixing in cement mortar 1:3 curing and cement etc. complete. Please Enable Macros to View BoQ information |
