|
| 1 | M & L for Roof treatment of RCC Roof Slab/Parapet Wall over roof in following steps :Surface Preparation: Clean all concrete surfaces free of laitance, dust, dirt, cavities, projecting nibs etc.by grinder and wire brush. Grease should be cleaned using a chemical degreaser and washed with clean water and allowed to dry. Remove all protrusions from concrete surfaces using a fine hair broom finish. Remove moss and lichen manually and treat the surface with a fungicide. Wash the surface thoroughly with clean water and allow it to dry. Standing water must be removed to prevent subsequent compromise of waterproof properties. For undulation of the existing slab shall be rectified with Shrinkage controlled, polymer modified, fibre reinforced cementitious repair mortar Renderoc SP40. Provide and Apply single coat of Lime mortar shall be applied at 1:3 ratio (Lime : sand) admixed with SBR based compound with 5-9 Liters Nitobond SBR Latex for additional layer of waterproofing, repair the covings, pot holes and any unevenness on Lime terrace roof. All around on the roof, at the parapet wall junction, an angular fillet of 50 mm X 50 mm. Free flow precision grout Conbextra GP2 poured within the leak-proof form work in accordance with the mix ratio as recommended in the technical data sheet of the manufacturer and then be sealed with an epoxy putty NITOCOTE VF. The surface is rendered to give aesthetic & visual surface finish complete all as specified and as directed. |
| 2 | Providing and carry out waterproofing treatment to sound, moisture free concrete surface using Nitoproof 600PF - Liquid applied single component pitch free polyurethane coating capable of bridging substrate cracks upto 2 mm. System includes proper surface preparation to remove loose dust, dirt, loose mortar, curing compound etc., and application of Nitoproof WB Primer, Water dispersible epoxy primer followed by two coats of Nitoproof 600PF coverage @ 2.0 kg/m2 to achieve 1.5 mm WFT in two coats followed by laying of separation layer of 120 gsm non-woven geotextile layer before carry out protection screed etc. complete including all tools and tackles as per manufacturer’s specification. The item rate shall be including of all kinds of labour, tools & tackle, machineries, lead & lift, mathadi charges, curing, wastages, consumable, cleaning, shifting of debris outside the site premises etc. complete as per design, drawing & instructions of EIC. Cost of 120 gsm non-woven geotextile and 75mm Screed concrete shall be paid separately. |
| 3 | Supply & Laying Geotextiles of 120 Gsm over the waterproofing coating to avoid damage during screed casting. Item rate is inclusive of materials all labour, tools and tackles, scaffolding and transportation etc. complete as per specification and as directed by EIC. |
| 4 | M & L for 50 mm thick Cement concrete type B-1, 1:2:4 (Using 20 mm graded crushed stone aggregate) mixed with suitable integral waterproofing compound conforming IS 2645:2003 @ 200ml per bag of cement and reinforced with PP fibers with proper slope towards RW pipes. Item rate is inclusive of materials all labour, tools and tackles, scaffolding and transportation etc. complete as per specification and as directed. |
| 5 | M&L 12mm thick gypsum board false ceiling fixed with standard GI frame work with and including plaster of Paris decorative type cornice all around at the junction of wall and ceiling etc GI perimeter channel 0.55 mm thickness with to unequal flanges of 20 & 30 mm & web of 27 mm fixed for the perimeter of the wall portion using nylon sleeves and screws at 450mm etc intermediate channel 0.9mm thickness with two equal flanges of 15mm each and wed 45mm suspended from the sofit 120mm c/c with ceiling hangers with GI cleat, ceiling section 0.55mm thickness with two equal flange 26mm thick & web of 50mm fixed a cross of the intermediated channel @ 457 mm c/c with connecting clips to hold the boards ceiling hanger 0.50mm thickness with two unequal flanges of 10 mm & 25mm used to suspended intermediate channel from sofit cleat @ 1220mm center, connecting clip 2.64 mm dia it is used to hold the ceiling section to the intermediate channel soffit cleat 0.55 mm thickness with two unequal flanges 37 mm & 25 mm and web of 25 mm used at 1220 mm c/c to the rowl plug to suspended ceiling hanger, rowl plug of 12.7mm dia used @ 1220 mm c/c in both directions, screws self drilling and tapping screws with under head cutter 25 mm and 35 mm long used to fix board to the metal frame @ 200 mm c/c ( 12mm away from the edge and 40 mm from the corners) and preparation of newly ceiling surfaces and a coat of wall care putty 3 mm thick(Average), sanding the surfaces till smooth finish is obtained and finally applying two coats of oil emulsion distemper over a coat of primer etc including dismantling of old ceiling of any description complete all as specified and as directed. |
| 6 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed. |
| 7 | M & L for rolled mild steel roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc confirming to grade Fe-410-W (Gde E 250) for fixing complete all as specified and as directed. |
| 8 | Demolition of plain cement concrete in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) complete all as specified and as directed. |
| 9 | M & L for 75mm thick PCC 1:3:6, type C2 (using 40mm graded crushed stone aggregate) as in plinth protection, etc finished the surface even and smooth without using extra cement including provision of joint of size 10 mm wide & 10 mm deep and filling with bitumen mastic joint filling at every 3m length and at corners complete all as specified and as directed. |
| 10 | Demolition of brick or stone masonry work built in cement mortar including all quoins, arches, pillars etc complete all as specified and as directed. |
| 11 | M&L for brick work with sub class ‘B’ bricks (locally available best quality) straight or curved on plan exceeding 6m mean radius, built in cement mortar 1:4 complete all as specified and as directed. |
| 12 | M&L for brick work with subclass ‘B’ bricks, (locally available best quality) straight or curved on plan to any radius in half brick thick wall, built in cement mortar (1:4) complete all as specified and directed. |
| 13 | M&L for rendering 10 mm thick in cement mortar (1:6) on fair faces/other than fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and as directed. |
| 14 | M&L for Granite (of any colour) tile 19-20 mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone with grinding and polishing over and including 15 mm thick screed bed in cement mortar 1:4 including dismantling of old tile of any description complete all as specified and as directed. |
| 15 | Providing edge moulding to 18-20mm thick granite stone slab including machine polishing to edge to give high gloss finish etc. complete all as specified and as directed. |
| 16 | Taking down chowkhats or frames with shutters (without taking off shutters from the frame) exceeding 1.5 sqm but not exceeding 4 sqm each complete all as specified and as directed. Note: Rate shall be deemed to be include for cutting holes/demolition of masonry walls etc for taking down chowkhats and making good the damaged surfaces. |
| 17 | Taking down chowkhats or frames with shutters (without taking off shutters from the frames) not exceeding 1.5 sqm complete all as specified and as directed.Note : Rate shall be deemed to be include for cutting holes/demolition of masonry walls etc for taking down chowkhats and making good the damaged surfaces |
| 18 | S&F factory made solid PVC door frame of size 40mm x 47mm made out of 5 mm thick plain colour PVC sheet reinforced with MS square tube complete all as specified and as directed. |
| 19 | S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing. |
| 20 | M&L for 2nd class hard wood, plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and as directed. |
| 21 | M&L for mild steel flat iron in bands, straps, supports or stays for pintle hinge, hand made sliding bolts, hold fast etc conforming to Fe-290 Gde-E-165 complete all as specified and as directed. |
| 22 | S&F 35mm thick second class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauge etc with plain, chamfered or rounded, mitred and rebated sash bars, any numbers for securing glass etc, sizes of members of shutters all as specified in SSR part-I section 8 clause 8.24 (a) complete all as specified and directed. |
| 23 | S&F 35mm thick 2nd class hard wood plain framed paneled shutter (any numbers of panel), factory made (two panel) with lock rail & panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces, the size of rail and style as per IS:1003 complete all as specified and as directed. |
| 24 | M & L for preparation of new wood or wood based surface of any description exceeding 10 cm width or girth and applying two coats of synthetic enamel paints over a coat of pink primer complete all as specified and as directed. |
| 25 | S&F 100 mm size stainless steel butt hinges, complete all as specified and as directed. |
| 26 | S&F 150 mm long extruded aluminium alloy handles, fabricated type anodised complete all as specified and as directed. |
| 27 | S&F 150mm long aluminium anodised barrel tower bolts of extruded section complete all as specified and directed. |
| 28 | S&F 250 mm long aluminum alloy anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of steel, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminum alloy complete all as specified and as directed. |
| 29 | S&F floor door stopper of aluminium alloy body and tongue, overall length of cover plate 150 mm anodised with hard drawn steel spring, fixed in floors complete all as specified and as directed. |
| 30 | S&F Powder coated (minimum thickness of powder coating 50 micron) anodised aluminium frames for door, windows, ventilators, partitions etc. with one or more rebates including joining cleat for fixing etc complete all as specified and as directed. |
| 31 | S&F Powder coated (minimum thickness of powder coating 50 micron) anodised aluminium window and ventilator shutters (sliding type), aluminium section weighing not less than 0.55 Kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading screws etc. complete all as specified and as directed. |
| 32 | S&F 4mm thick Sheet glass, selected quality glazing with rubber beading n exc. 0.5 sqm in each pane with solar coated film 25 micron reflective type complete all as specified and as directed. |
| 33 | S&F 3mm thick Figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane complete all as specified and as directed. |
| 34 | S&F stain-less steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and as directed. |
| 35 | S&F 25mm dia anodised aluminium tubular curtain rod including brackets, stops, rollers complete all as specified and as directed. Please Enable Macros to View BoQ information |
