|
| 1 | Taking down cement plaster on walls, chajja surfaces, etc including raking out joints, hacking for key, scrubbing down with water complete all as specified and directed. |
| 2 | M & L for rendering 15 mm thick in cement mortar (1:6) on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and as directed. |
| 3 | M&L for 15mm thick rendering in cement mortar (1:4), in two layers, under coat of 10 mm thick & top of 5 mm thick, to other than fair faces of brick or concrete wall surfaces, top layer 5 mm thick mixed with water proofing compound @ 200Ml per bag(50Kg) of cement or as per manufacture's instructions, finished even and smooth without using extra cement complete all as specified and as directed. Note : Water proofing compound will be measured and paid separately as \\"Supply only\\". |
| 4 | M&L for rendering 5 mm thick in cement mortar (1:3) as in ceiling surface finished even and smooth without using extra cement complete all as specified and as directed. |
| 5 | Supply only liquid water proofing compound complete all as specified and as directed. |
| 6 | M&L for cleaning vertical and horizontal surfaces of unplastered masonry wall and concrete surfaces for loose materials/dust and applying two coats of epoxy resin component (Dr. Fixit DAMPGUARD or equivalent) solution/mix using nylon brush pouring Base part in attain homogeneous smooth paste and dilute the mixed compound with water in ration 1 part Base: 1 part Harder : 1 part water by slow addition and mix thoroughly until a brushable consistency is obtained, apply the first coat using a brush or roller and dry for 6 to 8 hours and second/ final coat coat at a 90° angle (cross-coating) to the first including curing treated surface for 24 hrs complete all as per manufacturer instruction. |
| 7 | Grubbing up tree trunk including cutting of trunk portion, girth of tree not exc 30 cm, protruding over ground / building / wall / root / chajja / stack pipes etc. digging out roots, and applying root killer chemical as per manufacturer's instructions, filling holes with cement mortar (1:4) or PCC 1:2:4 type B-0 and removing the unserviceable materials from the site complete all as specified and as directed. |
| 8 | Complete removal of existing treatment & levelling of wall/ceiling surface using MECHANICAL / ELECTRICAL OPERATED SANDING / SCRAPING MACHINE WITH INBUILT VACCUM SUCTION system to suck the existing treatment as retrieved by scrapping/sanding etc for obtaining smooth paintable surface complete all as specified and as directed. |
| 9 | M & L for applying 1mm (Average) thick wall care putty on newly plastered or old prepared surfaces of wall and ceiling complete all as specified and as directed. |
| 10 | M&L for preparation of new plastered surfaces of wall and ceiling and applying two coats of acrylic distemper 1st quality (ready mixed) having VOC content less than 50 gms/ltrs of required shade and colour complete as per manufacturer's specification complete all as specified and directed. |
| 11 | M&L for preparation of old plastered surfaces of wall and ceiling and applying one coat of acrylic distemper 1st quality (ready mixed) having VOC content less than 50 gms/ltrs of required shade and colour complete as per manufacturer's specification complete all as specified and directed. |
| 12 | M & L for preparation of old plastered surfaces of wall and applying one coat of white wash complete all as specified and as directed. |
| 13 | M & L for preparation of old plastered surfaces of ceiling and applying one coat of white wash complete all as specified and as directed. |
| 14 | M & L for preparation of newly plastered surfaces of walls and applying Two or more coats of 100% Premium exterior acrylic emulsion paint of required shade, having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm complete all specified and as directed. |
| 15 | M&L for preparation of old decorated surfaces of walls and applying one coat of acrylic emulsion weather coat paint complete all as specified and as directed. |
| 16 | M&L for preparation of old decorated surfaces of walls and applying two coats of cement base paint using roller technic complete all as specified and as directed. |
| 17 | M&L for preparation of old decorated surfaces of walls and applying one coat of cement base paint using roller technic complete all as specified and as directed. |
| 18 | M&L for preparation of old painted surfaces of wood or wood based materials of any description exceeding 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed. |
| 19 | M&L for preparation of old painted surfaces of steel and iron work of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed. |
| 20 | M&L for preparation of old steel or iron surfaces of any description n exc 10cm width or girth and applying one coats of synthetic enamel paint complete all as specified and as directed. |
| 21 | M&L for Painting lines, dashes, arrows, letters, etc. on roads, pavements, kerbs, parapets, etc in adequate Nos of coat as directed to obtained bright finishes colour/texture and the like, exc 10cm wide with reflective road marking paint, white or golden yellow or black in colour complete all as specified and as directed. |
| 22 | S&F Bldg Nos board of size 350mm x 250mm, made of 3mm thick ACP (Aluminium composite panel) conforming to IS- 17682:2021, , covered with high intensity grade (Class C, Type VIII, IX, XI) retro reflective sheeting of green colour as per IRC standard meeting on one side with computer cut letters on high intensity grade retro reflective sheet (White colour) marking Bldg Nos and fixed with SS screws on four corners to walls using PVC plugs complete all as specified and as directed. (Make of ACP board : Alex panel/ Eurobond/ Alstrong or equivalent) & (Make of retro reflective sheet : 3M/ Darkeye/ Avery). |
| 23 | Taking down chowkhats or frames with shutters (without taking off shutters from the frames) not exceeding 1.5 sqm complete all as specified and as directed.Note : Rate shall be deemed to be include for cutting holes/demolition of masonry walls etc for taking down chowkhats and making good the damaged surfaces |
| 24 | Taking down shutter of any description area exc 1 sqm but n exc 2 Sqm each including builders hardware complete all as specified and as directed. |
| 25 | S & F 35 mm thick Flush door shutters, solid core construction, with particle board core and plywood face panels, commercial type on both sides one face is covered with decorative face veneer with lipping/frame to match complete all as specified and as directed. |
| 26 | S&F 35mm thick second class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauge etc with plain, chamfered or rounded, mitred beads (without sash bars) for securing glass etc, sizes of members of shutters all as specified in SSR part-I section 8 clause 8.24 (a) complete all as specified and directed. |
| 27 | M & L for preparation of new wood or wood based surface of any description exceeding 10 cm width or girth and applying two coats of synthetic enamel paints over a coat of pink primer complete all as specified and as directed. |
| 28 | S&F 100 mm size stainless steel butt hinges, complete all as specified and as directed. |
| 29 | S&F 200mm size aluminium handles, cast type, anodised complete all as specified and as directed. |
| 30 | S&F 200mm long aluminium anodised barrel tower bolts of extruded section complete all as specified and directed. |
| 31 | S & F 250 mm long aluminum alloy anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of steel, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminum alloy complete all as specified and as directed. |
| 32 | S&F steel helical door spring 300mm ordinary rat tail rod pattern springs including roller plate complete all as specified and as directed. |
| 33 | S & F floor door stopper of aluminium alloy body and tongue, overall length of cover plate 150 mm anodised with hard drawn steel spring, fixed in floors complete all as specified and as directed. |
| 34 | S&F powder coated anodised aluminium alloy sections 3 tier track sliding windows Series B (Jindal aluminium window section catalogue) weight of section frame 1.248 kg/m and shutter section weight 0.547 kg/m duly fitted with neoprene beading, glazing clips, tinted glass panes 4.8/5 mm nominal thickness, aluminium expanded mosquito proof wire cloth 0.45 mm thick and average width of aperture 1.4 mm, aluminium alloy handles etc complete all as specified and as directed.Note : Rate shall include all glazing/aluminium expanded wire cloth, rubber packing, joining, cleats, glazing clips, aluminium snap beading, locking arrangements, handle etc. |
| 35 | S & F powder coated anodised aluminium ventilator with fixed aluminium frame of size 65 x 40 x 1.98 mm thick or equivalent section fixed in vertical position with aluminium vertical members and half portion to be provided with 4 mm thick pinhead frosted glass and remaining portion to be louvered using 4 mm thick pinhead frosted glass and outer side louvered portion covered with aluminium expanded mosquito proof wire cloth 0.45 mm dia and average width of aperture 1.4 mm with necessary frame work, rubber gasket and aluminium beading complete all as specified and as directed.Note : Rates shall include all glazing/aluminium expanded wire cloth, rubber packing, joining, cleats, glazing clips, aluminium snap beading etc |
| 36 | S&F for Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; frame work of water tanks and similar work conforming to Fe 290, Gde-E-165 completed all as specified and directed. |
| 37 | M&L for preparation of new steel or iron surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paints over a coat of red oxide, zinc chrome primer complete all as specified and as directed. |
| 38 | Taking down old steel window shutter for caring out all repair work including change of box hinges, steel handle, steel hook & eye if required and refixing in the same opening complete all as specified and directed. |
| 39 | S & F in repairs, Aluminium wire cloth, expanded mesh type, 0.45 nominal dia of wire and average width of aperture 1.40mm fixed with aluminium wire staples, nails, screws, beads, etc in wooden/metal joinery as required complete all as specified and as directed. |
| 40 | S & F 3mm thick sheet glass, ordinary quality and glazing with oil putty, headless nails, clip, beads, wooden beads as required in square n exc 0.5 sqm in each pane including hacking out old broken glass of any thickness, size quality or description from Aluminium, metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones complete all as specified and as directed. |
| 41 | S & F 4mm thick Non asbestos fiber cement building boards of size 605x605mm with Anodised aluminium snap grid frame work and Hangers 6 mm dia GI (Up to 1200mm length ) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 X 3mm size 60mm long and expansion hold fasteners 12.50mm dia 40mm long for false ceiling, flat or sloping fixed or laid/ inserted to Aluminium framework with screws including dismantling of old ceiling of any description complete all as specified and as directed. Please Enable Macros to View BoQ information |
