|
| 1 | Demolition of cement concrete of any description and in any position(above/below of ground level) not otherwise specifically provided as in sunken floor, plinth protection, roof kerb, foundation etc. all as specified and directed. |
| 2 | M&L for water proofing treatment to sunken floors with application of two components acrylic modified cementious coating with glass fabric sheet between coats (SIKA Top Seal-107 / Brush Bond FOSROC / Dr. Fixit / STP / CICO ) on dried surface free from containments such as dirt, dust, oil, surface treatments and old coatings. Concrete substrats must be prepared mechanically using abrasive blast cleaning or milling to remove cement laitance existing coating and achieve a gripping clean dry and free from laitance profile. The installation instructions of Manufacturer should be followed strictly. Note : (a) Chipping out any visible cracks must be clean and filled with SIKA latex SBR 100 Putty / Dr. Fixit 302 SBR latex / Perma latex SBR / FOSROC Nitbond SBR latex / Asain Paint latex in \\"V Groove\\" pattern and finally clean surface with powder grinder, wire brush hair brush & Vaccum pressure.(b) The waterproofing coating should be taken upto a height of 450mm above the FFL on vertical surfaces. (c) Second coats shalll be applied after 6-8 hrs of application of previous coat and in the right angle direction. (d) All traps in sunken slabs to be enclosed with PCC (1:1:5:3) type B-0 (using 12.5mm graded crushed stone aggregate) (min 150mm) al-around. |
| 3 | M&L for rendering with ready mix mortar 15mm thick in sunken portion of slab using waterproofing compound all as specified and directed |
| 4 | M&L for PCC 1:5:10 type E2 (using 40 mm graded crushed stone aggregate) as in filling, foundation and mass concrete in sunken floor complete all as specified and directed. |
| 5 | M&L for 25 mm thick cement concrete 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregate) as in sub base for receiving the floor finishes complete all as specified and directed. |
| 6 | Roughening the surface of old concrete floor picking sweeping cleaning and washing down with water to remove dust/mud etc.and applying a coat of Nitobond SBR Cement Slurry (1 Vol of Nitobond SBR + 1 vol of Water + 3 vol of cement) water proofing coating on roof , complete all as specified and directed. |
| 7 | M&L for cement concrete 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregate) as in roof padding averaging thickness of 50 mm complete all as specified. |
| 8 | M&L APP based polymeric membrane minimum weighing 3 kg/ Sqm and minimum 3mm thick, reinforced with polyster non wove fabric (weight not less than 150 gms/ Sqm) laid on applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per sq.m by forced application with butane torch over entire roof area with minimum overlaps of 100mm at the sides/ longitudinal edges of strips membrane and 150mm at the ends and sealed in after cleaning surface complete all as specified and directed and all as per manufacturer's instructions. |
| 9 | S&F prepartion of new surface and applying two coats of aluminum paint on above of APP Membrane complete all as specified and directed. |
| 10 | M&L for ceramic glazed dark shade coloured tiles of size 450x300x7mm thick joint free on and including 10mm thick screed bed in CM(1:4) set and jointed in neat cement slurry and pointed in colored cement mixed with pigment to match the colour of tiles on vertical surfaces of wall as in skirting/ dado and dismantling of existing tile complete all as specified. |
| 11 | M&L for non skid dark coloured ceramic tiles 7 to 8 mm thick joint free (square/rectangular) area of each tile exceeding 0.11 sqm to 0.18sqm in floors etc set and jointed in neat cement slurry and pointed in white cement or clolured cement to match including 15 mm thick screed bed in CM 1:4 and demolition of existing tile complete all as specified. |
| 12 | M&L for green marble work 14-16 mm thick (table rubbed and polished) in steps, jambs, pillars window cills, cooking platforms, stair case and like in cement mortar ( 1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade including 15 mm thick screed bed in CM 1:4 and demolition of existing marble with screed complete all as specified and directed. |
| 13 | M&L for non skid dark coloured ceramic tiles 7 to 8 mm thick joint free (square/rectangular) area of each tile exceeding 0.18 sqm to 0.38 sqm in floors etc set and jointed in neat cement slurry and pointed in white cement or coloured cement to match including 15 mm thick screed bed in CM 1:4 and demolition of existing tile complete all as specified. |
| 14 | M&L for dark or light coloured vitrified tiles10 mm thick, double charged joint free (square/rectangular) area of each tile n exc 0.36 sqm in floors etc set and jointed in neat cement slurry and pointed in white cement or clolured cement to match including 15 mm thick screed bed in CM 1:4 and demolition of existing tile complete all as specified and directed. |
| 15 | M&L for 75mm thick cement cocnrete 1:3:6 type C-1 (using 20mm graded crushed stone aggregate) as in plinth protection finishing the surface even and fair complete all as specified and directed by Engineer-in-Charge. |
| 16 | M&L for PCC 1:2:4 type B1 (using 20mm graded crushed stone aggregate) as in roof kerbs or mud stops, rounded or chamfered on edges with WPC complete all as specified and directed.Note : WPC shall be measured and paid separately. |
| 17 | Demolition of brick work or stone boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc complete all as specified and directed |
| 18 | M&L for brick work with sub class 'B' old size bricks, straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified and directed. |
| 19 | M&L for brick work with sub class 'B' bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified and directed. |
| 20 | M&L for repairing of RCC projections, chajjas, roofs, facia etc. by chipping off existing loose, damaged concrete and applying two coat of polymer modified cementitious mortar on epoxy bond coat on dry sub strate & free from debries / dust surfaces of concrete complete all as specified and directed by the manufacturer. (Note:- Cost of formwork and welded mesh, bldg shall be deemed to be included in unit rate quoted by the Contractor). |
| 21 | M&L for rendering 15mm thick with ready mix mortar of approved make on brick or concrete surfaces of walls, finished surface even and fair with WPC upto ht. 12 mtr including taking down cement plaster of any description, complete all as specified and directed.Note : WPC shall be measured and paid separately. |
| 22 | M&L for rendering 12mm thick with ready mix mortar of approved make on brick or concrete surfaces of walls, finished surface even and smooth without using extra cement including taking down cement plaster of any description, complete all as specified and directed. |
| 23 | M&L for rendering 5mm thick with ready mix mortar of approved make on ceiling finished surface even and smooth without using extra cement including taking down cement plaster of any description complete all as specified and directed. |
| 24 | M&L for preparation of new plaster surface and applying two coats of cement base paint on wall surface complete all as specified and directed. |
| 25 | M&L for preparation of new plaster surface and applying two coats of oil bound distemper over a coat of primer on plastered surface wall complete all as specified and directed. |
| 26 | M&L for preparation of new plaster surface and applying three coat of white wash on wall complete all as specified and directed. |
| 27 | M&L for preparation of new plaster surface and applying three coat of white wash on Engineer-in-Charge. |
| 28 | M&L for complete removing of existing treatment from wall / ceiling by using mechanical sander/grinder and applying 1 to 1.5mm thick acrylic damp proof wall care putty as per manufacturers instructions, complete all as specified and directed. |
| 29 | M&L for preparation of puttied wall / ceiling by mechanical sander/grinder and applying two coats of oil bound emulsion distemper over a coat of primer, complete all as specified and directed |
| 30 | M&L for preparation of puttied wall / ceiling and applying two coats of 100% premium exterior acrylic emulsion paint of apex ultima or equivalent having VOC less than 50gm/ litre and UV resistance as per IS 15489-2004, Alkali & fungal resistance dirt resistance exterior paint of required shade company depot tinted with silicon additives complete all as specified and directed. |
| 31 | M&L for preparation of old plastered surfaces of ceiling by brooming down, making good holes, cracks, etc and applying one coat of white wash incl cleaning the floor/ joinery surfaces, glass pans all as directed by Engineer-in-Charge. |
| 32 | M&L for preparation of old plastered surface of walls rubbing down, making good holes, cracks, etc and stopping etc on existing distempered surfaces and applying one coats of oil bound emulsion distemper on wall incl cleanning the floor/ joinery, surfaces, glass pane complete all as specified and directed by Engineer-in-Charge. |
| 33 | M&L for preparation of old plastered surface of walls rubbing down, making good holes, cracks, etc and stopping etc on existing distempered surfaces and applying one coats of cement base paint on wall complete all as specified and directed by Engineer-in-Charge. |
| 34 | M&L for preparation of old plastered surfaces of wall by brooming down, making good holes, cracks etc and applying one coat of white wash complete all as directed by Eng-in-charge. |
| 35 | S&F steel window box type made of ERW tube hollow P section of size 60mmX25mm double rebated outer frame comprising double shutters i.e. guaged skelton & glazed, shutter frame of ERW tube P section size 50mmX20mm with two openable leaf for each shutter consisting two Nos sash bar of T-section 20mmX3mm welded to frame with one vertical mullion of ERW box type T-section of size 60mmX25mm and FI 2mm thick welded/ screwed to frame for fixing of wire gauge including MS guard bars, fittings and fixtures welded to frame/ shutters as given below and all as shown on drg No. CEJZ/TD-1020/08 Sh 1/3 to 3/3 completeincl two coat of painting incl taking down old existing window :- (i) Hold fast,150mm long of flat iron 12mmX3mm- 04Nos per window (ii) Handle of Z section 20mmX25mm,100mm long-01Nos per leaf (iii) MS Tower bolt 150mm long-02 Nos per leaf (iv) Z section 20mmX25mm,100mm long stopper -01 Nos per leaf (v) Cleat 55mm long of hollow square 15mmX12mm -02 Nos per leaf (vi) MS pintol hinges size 75mmx12mm- 2 Nos. per leaf (vii) Making good dismantled portion in PCC 1:2:4 type B-1 for hold fasts (four Nos for each window). (viii) Painting with one shop coat of zinc chromate primer. (Note: Wire cloth, glass shall be measured and paid for separately). |
| 36 | S&F steel window/ ventilator box type made of ERW tube hollow P section of size 60mmX25mm outer frame (single rebated) comprising glazed skelton shutter frame of ERW tube P section including MS guard bars, fittings and fixtures welded to frame/ shutters all as shown on drg No. CEJZ/TD-1019/08 Sh 1/3 to 3/3 including Making good dismantled portion in PCC 1:2:4 type B-1 for hold fasts, painting with one shop coat of zinc chromate primer incl two coat of painting incl taking down old existing window/ventilator complete all as specified and directed. Note: Glass/ wire cloth shall be measured and paid for separately |
| 37 | S&F anodised aluminium frame for doors, windows, ventilators, partitions with one or more rebates including joining cleat for fixing etc complete all as specified and directed. |
| 38 | S&F anodised aluminium door shutters, aluminium section weighing average not less than 1.00kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified and directed. |
| 39 | S&F anodised aluminium window/ ventilator shutters side hung type without sash bars, aluminium section weighing average not less than 0.75 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.) hinges type B-21 100mm long (2 no.) suitable handle (1 no.) , complete all as specified and directed |
| 40 | S&F anodised aluminium grill of 5mm thick (anodised transparent or dyed to required shade according to IS : 1868 with minimum anodic coating of grade AC 15) of approved design / pattern, with approved standard section and fixed to the existing window frame with suitable aluminium channel and CP brass / stainless steel screws @ 200mm centre to centre including cutting the grill to proper opeing size for fixing and operation of handles and fixing approved anodised aluminium standard section alround the opeing, complete all as specifed and directed. |
| 41 | S&F 4.8mm thick black sheet glass ordinary quality in squares or rectangular not exceeding 1.00 sqm in each pane in aluminium door or window shutter complete all as specified and directed |
| 42 | S&F in repair 4.8mm thick black sheet glass ordinary quality in squares or rectangular not exceeding 1.00 sqm in each pane in aluminium door or window shutter incl rubber packing, anodised aluminium snap beading complete all as specified and directed |
| 43 | S&F of 4mm thick aluminium composite pannel (ACP) sheet for aluminium door/window complete all as specified and directed. |
| 44 | S&F in repair 4mm thick aluminium composite pannel (ACP) sheet for aluminium door/window complete all as specified and directed. |
| 45 | M&L for petty repair to existing in built aluminium door, locks, hinges incl necessary making the lock/ glass/ adjusting shutter complete serviceable all as per existing pattern as directed by Engineer-in-Charge incl provision of duplicate keys as required. |
| 46 | S&F in repairs mortice lock, aluminium vertical type size 65mm 2 levers complete all as specidfed and directed. |
| 47 | S&F in repairs aluminium (die cast) body door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg complete all as specified and directed. |
| 48 | S&F in repair floor door stopper 140 mm size of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete complete all as specified and directed. |
| 49 | Taking down chowkats with shutter n.exc 1.50 Sqm each (without taking off shutter for the chowkats) complete all as specified and directed. |
| 50 | Taking down chowkats with shutter exc 1.50 Sqm but n exc 4.00 sqm each (without taking off shutter for the chowkats) complete all as specified and directed. |
| 51 | Taking down shutter of any description exc 1.00 Sqm but n.exc 2.00 Sqm each complete all as specified and directed. |
| 52 | S&F pressed steel frame for doors with one or more rebate including necessary fixing lugs, hings, lock strike, plate etc complete of size 105x60mm all as spd including two coats of painting over a coat of factory primer and filling PCC 1:3:6 type B-0 (using 12.5mm graded crushed stone aggregate) in the frames complete all as specified and directed. |
| 53 | S&F pressed steel frame for doors with one or more rebate including necessary fixing lugs, hings, lock strike, plate etc complete of size 125x60mm including two coats of painting over a coat of factory primer and filling PCC 1:3:6 type B-0 (using 12.5mm graded crushed stone aggregate) in the frames complete all as specified and directed. |
| 54 | S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed. |
| 55 | S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and directed. |
| 56 | S&F 30 mm thick flush shutters, solid core construction, with block board core and plywood face panels on both side complete all as specified and directed. |
| 57 | S&F 2nd class hard wood factory made glazed and skeleton shutters 35mm thick, open rebated and prepared to receive glass, gauze, etc. but divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc , sizes of members of shutters as specified in SSR Part-I, Section 8 clause 8.24 (a) complete all as specified and directed. |
| 58 | S&F factory made WPC door frame of 45 x 70mm section, single extruded comprising of virgin PVC polymer of K Value 58 - 60 (suspension grade) calcium carbonate and natural fibers (wood powder/rice husk / wheat husk) and non toxic additives (maximum toxicity index 12 for 100 gms) fabricated with meter joint after applying PVC solvent cement and screwed with fully body threaded star headed stainless steel screw having minimum frame density of 750 Kg/Cum screw withdrawal strength 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, Modulus of elasticity 900 N /mm2 and resistance to spread of flame of Class A category with properties of being termite / borer proof, water/moisture proof and fire retardant and fixed in position with MS hold fast fasteners of required dia and length complete as per specification of the manufacturer and as specified & directed by Engineer-in-Charge. |
| 59 | S&F 30mm thick factory made natural fiber compositie door shutter with CNC cutting of required size having minimum 40 % high strength plant derived fibers, consisting of thermoset polymers, non - toxic additives (minimum toxicity index of 12 for 100 gms), having density of 650 kg/Cum, modulus of elasticity (3-4), screw withdrawal strength of 1800 NN (Face) and 900 N (Edge) having interlaminar shear strength and thermal stability complete all as per specification of the manufacturer and as specified & directed by Engineer-in-Charge. |
| 60 | S&F stainless steel wire cloth, 0.40mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tack/wooden beads or galvanised wire staples complete all as specified and directed. |
| 61 | S&F in repair stainless steel wire cloth, 0.40mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed. |
| 62 | S&F 4mm thick sheet glass ordinary quality and glazing with oil putting in squares nexc 0.50 Sqm each complete all as specified and directed. |
| 63 | S&F in repair 4mm thick sheet glass ordinary quality and glazing with oil putting in squares nexc 0.50 Sqm each incl hacking out of old broken glass panes from wooden or steel frame complete all as specified and directed. |
| 64 | M&L for preparation of new wooden surface exc 10cm width or girth and applying two coat of synthetic enamel paint over one coat of pink primer complete all as specified and directed. |
| 65 | M&L for preparation of new steel surface exc 10cm width or girth and applying two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. |
| 66 | S&F in repair 300mm, mild steel ordinary rat tail rod pattern springs, including roller and roller plate joint through welding/ bolt in metal/wooden frame to be carried out complete all as specified and directed. |
| 67 | S&F aluminium anodized barel tower bolt of extruded section 150mm long ISI marked complete all as specified and directed. |
| 68 | S&F aluminium alloyed handle fabricated type anodized of size 150 mm long ISI Marked complete all as specified and directed. |
| 69 | S&F 100mm size butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 through bolt or with screw complete all as specified and directed. |
| 70 | S&F aluminium alloy, anodised, sliding door 300 mm long ISI marked bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed. |
| 71 | S&F in repair drapery rod in any length, high strength stainless steel pipe having outer dia 28mm with a pair of brakets of any shape/design complete all as specified and directed . |
| 72 | S&F in repair 18/19 mm thick one side prelaminated colour WPC board for cup board shutter and frame & fixed at site complete alll as spcecified and directed. (Note : Board edges properly fnished with strip on band edges). |
| 73 | S&F aluminium alloyed handle fabricated type anodized of size 100 mm long complete all as specified and directed. |
| 74 | S&F 75mm size hasp and staple safety type aluminium anodised brass with mild steel hinge pin including bolt to hinge plate and fixed with screw complete all as specified and directed. |
| 75 | S&F in repair 3-4 mm thick UV marble sheet wall panelling printed inclusive of adeshive to fixed at site with tipper strip weather proof, water proof, termite proof including all C and U type section with matching of panelling fixing at border of panelling and complete all as specified and directed by Engr-In-Charge. |
| 76 | S&F in repair 7-8 mm thick PVC hollow wall panelling consisting of wood grain printed pvc sheet inclusive of solvant cement and fixing at site on PVC frame formed by sticking high density EPS, flame retardent (TF) grade, heavy duty with tipper strip weather proof, water proof, termite proof including all C and U type PVC section with matching of panelling fixing at border of panelling and complete all as specified and directed by Engr-In-Charge. |
| 77 | S&F 4mm thick E Board false ceiling (Classic) including galvanised colour coated snap grid frame for false ceiling, size of grid 605 x 605 mm fixed with 1.6mm dia GI Wire suspenders one end tied to roof members and other end connected to main tee of grid framework by means of 4mm dia adjustable J Hook consisting of two nos washers and two nuts at 1.2mtr centre siae of main tee 38x 25 x 1.4mm, Cross Tee 38 x 25 x 1.4mm, angle along with walls 38 x 25x 2.00mm and including taking down existing boards of any thickness including cover fillets etc complete all as specified and directed |
| 78 | S&F 500 ltr capacity rotational moulded polyethylene 3-layer white water storage tanks (cylindrical vertical with closed top) hoisted and fixed in postition all as specified in SSR Part I including dismantling of water tanks complete all as specified and directed. |
| 79 | S&F 1000 ltr capacity rotational moulded polyethylene 3-layer white water storage tanks (cylindrical vertical with closed top) hoisted and fixed in postition all as specified in SSR Part I including dismantling of water tanks complete all as specified and directed. |
| 80 | S&F 2000 ltr capacity rotational moulded polyethylene 3-layer water storage tanks (cylindrical vertical with closed top) hoisted and fixed in postition all as specified in SSR Part I including dismantling of water tanks and removing to store, complete all as specified and directed by Engr-in-Charge. |
| 81 | S&F in repair ball brass valve, high pressure, with polythene float and flynut complete, screwed for iron pipe 20mm bore complete all as specified and directed. |
| 82 | S&F in repair stop value 20mm bore cast copper alloy with butterfly handle screwed down for high pressure, screed on bath ends, fixed with iron pipe etc complete all as specified and directed. |
| 83 | S&F in repair stop valves or angle valve cast copper alloy 15mm bore fancy type chromium plated alloy with butterfly handle screwed down for high pressure, screed on bath ends, fixed with iron pipe etc complete all as specified and directed. |
| 84 | S&F in repair bib taps cast copper alloy 15mm bore fancy type chromium plated alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed. |
| 85 | S&F in repair pillar taps, cast copper alloy fancy type, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe 15mm bore and fixed. |
| 86 | S&F in repair brass chromium plated shower rose fancy type 125mm size with swivel joints, any size, including fixing to steel pipe or union with brass CP arm 195mm long, 15 mm size complete all as specified and directed. |
| 87 | S&F in repair brass chromium plated tubular towel rail 20mm dia, D type, 60 cm long with flanges complete all as specified and directed by Engr-in-Charge. |
| 88 | S&F in repair health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified complete all as specified as directed |
| 89 | S&F in repair 15 mm brass CP WHB mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed. |
| 90 | S&F in repairs vitreous china wash down water closet (pedestal pattern) fixing with bolts ,white colour including stainless steel L-type jet spray with 1m hose pipe, connection to trap, and to flushing pipe, anti-syphonage pipe, etc. incl seat covercomplete including making good to floor complete all as specified and directed. |
| 91 | S&F in repair vitreous china squatting pan “Orrisa Pattern” white of size 580x440mm with integral foot rest with `P’ or `S’ trap including water connection to trap and flushing pipe etc complete and bedding in PCC 1:7:12 type F-2 (using 40mm graded crushed stone aggregate) complete all as specified and directed. |
| 92 | S&F in repair vitreous China wash basin, with pedestal white flat back, size 550x 450mm excluding taps, waste, chain and plug and porcelain stopper but including brackets and coupling complete all as specified and directed. |
| 93 | S&F in repair vitreous China table top wash basin, white rectangular bowl, size 550X400X140mm excluding taps but including coupling complete all as specified and directed. |
| 94 | S&F in repair vitreous china urinal, half stall type, white (excluding flushing cistern) white with grating, waste coupling and union for discharge pipe complete including providing and fixing plugs bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass screw, pointing aroug urinal back in cement, grating and union for discharge pipe incl PTMT waste coupling, waste pipe, urinal spreader complete all as specified and directed. |
| 95 | S&F in repair vitreous china coloured WC Italian finish pedestal pan with attached vitreous china flushing cistern (monolithiic type) of push button type having dual flushing cistern of same colour including pvc seat cover same colour including CP Jet chromium plated with pvc connection 15mm bore complete all as specified and directed. |
| 96 | S&F in repair vitreous china counter top oval wash basin, white, size 550x400mm including waste coupling and waste pipe complete all as specifed and directed. |
| 97 | S&F in repair Vitreous china urinal partition white of size 310x700 mm fixed with wall by steel screw complete all as speciifiwed and directed. |
| 98 | S & F in repair PVC low level dual flushing cistern 10ltr capacity, with syphonic, action PVC float valve, brackets and 32mm bore PVC flush pipe etc complete all as specified and directed. |
| 99 | S&F in repair PVC waste pipe 32mm dia 1200 mm long fixed to wash fitting of wash basin and sink all as specified and directed. |
| 100 | S&F in repair PVC connections 15 mm size with PTMT nuts of length 600 mm complete all as specified and directed. |
| 101 | S&F in repair grating doom 100 mm dia with waste hole, complete all as specified and directed. |
| 102 | S&F in repair stainless steel L-type jet spray with 1m hose pipe for fitting in WC complete all as specified and directed. |
| 103 | S&F GI tubing 15mm bore medium grade, fixed to wall/ ceiling or floor etc with all fittings ISI marked including taking up or down complete all as specified and directed. |
| 104 | Fixing only GI pipe 15mm bore (old serviceable pipe re-used). |
| 105 | S&F GI tubing 20mm bore medium grade, fixed to wall/ ceiling or floor etc with all fittings ISI marked including taking up and down complete all as specified and directed. |
| 106 | Fixing only GI pipe 20mm bore (old serviceable pipe re-used). |
| 107 | S&F GI tubing 32mm bore medium grade, fixed to wall/ ceiling or floor etc with all fittings including taking up or down old pipe complete all as specified and directed. |
| 108 | Dismantling of cast iron, PVC or SGSW drain pipes, jointed in cement mortar and taking out of trenches, if required. |
| 109 | S&F PVC (SWR) pipes 110mm dia in any length with rubber ring joint fixed to wall/floor upto 12m height complete all as specified and directed. |
| 110 | S&F PVC (SWR) pipes 75mm dia in any length with rubber ring joint fixed to wall/floor height complete all as specified and directed. |
| 111 | S&F in repair PVC (SWR) bends 110mm dia, in any radius, complete all as specified and directed. |
| 112 | S&F in repair PVC (SWR) bends 75mm dia, in any radius, complete all as specified and directed. |
| 113 | S&F in repair 110 bore PVC(SWR) branch pieces (Single T), single (equal or unequal ), ordinary or inverted) or with parallel branches with oval access door complete all as specified and directed. |
| 114 | S&F in repair 75 bore PVC(SWR) branch pieces (Single T), single (equal or unequal), ordinary or inverted) or with parallel branches with oval access door complete all as specified and directed. |
| 115 | S&F in repair PVC vent cowl of size 110mm. |
| 116 | M&L in repair for PVC(SWR) floor trap plain including jointing with solvent cement 100mm dia complete all as specified and directed. |
| 117 | M&L in repair for PVC(SWR) floor trap plain including jointing with solvent cement 75mm dia complete all as specified and directed. |
| 118 | S&F in repair stack clamps (110 mm pipe) out of 20x1.5 mm galvanised mild steel incl stays, bolt and nuts and securing ends of stays to wall or roof complete all as specified and directed. |
| 119 | S&F in repair stack clamps (75 mm pipe) out of 20x1.5mm galvanised mild steel incl stays, bolt and nuts and securing ends of stays to wall or roof complete all as specified and directed. |
| 120 | M&L for removal of blockage between manholes to manhole lines of various sizes & at any depth for sewage by means of (rodding, by any mechanised means or any other sources) including removing rugs of any type, dirt etc complete all as specified and directed. |
| 121 | M&L cleaning of blockage of WC Indian or European type by removing of all the mud/sludge and getting out including cleaning of SGSW or CI pipe upto First manhole and depositing the sludge in a pit of suitable size at a distance not exceeding 50 meters from the WC and covering the same with the soil obtained from excavation of pit including all excavation and earth work complete all as specified and directed by Engr-in-Charge |
| 122 | M&L cleaning the blockage of bathroom/kitchen by cleaning the nahni traps/gulley traps of all the mud/sludge and getting out, washing thoroughly grating of trap, CI waste pipes by opening the clearing eyes and depositing the sludge in a pit of suitable size at a distance not exceeding 50 meters from the gully trap and covering the same with the soil obtained from excavation of pit including all excavations and earthwork complete all as specified and directed by Engr-in-Charge Please Enable Macros to View BoQ information |
| 123 | M&L cleaning the blockage of bathroom/kitchen by cleaning the nahni traps/gulley traps of all the mud/sludge and getting out, washing thoroughly grating of trap, CI waste pipes by opening the clearing eyes and depositing the sludge in a pit of suitable size at a distance not exceeding 50 meters from the gully trap and covering the same with the soil obtained from excavation of pit including all excavations and earthwork complete all as specified and directed by Engr-in-Charge Please Enable Macros to View BoQ information |
