|
| 1 | Demolition of cement concrete (un reinforced) in ground floors and paving n.exc 15cm thickness (below or above ground (level) and lowering if necessary, removal of the rubbish off the premises all as specified and directed. |
| 2 | Demolition of cement concrete (reinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level).and lowering if necessary, removal of the rubbish off the premises all as specified and directed. |
| 3 | M & L for cement concrete 75 mm thick type B- 1, 1:2:4 (20 mm graded aggregate) laid on concrete floors and pavings; laid over cement concrete subfloors etc. and finished to an even and rough surface as specified and as directed by Engg-in-charge. (Note: Reinforcement will be measured and paid separately) |
| 4 | Dismantling wall and ceiling board of any descrition complete all as specified and directed. |
| 5 | S&F in repairs 18/19 mm thick, lead free PVC board Superior quality of density not less than 0.55 g/cm3 as in moduler shutters/cabimet drawer cupboard cabinet shutter including all frame work as specified and directed by Engr-in-Charge |
| 6 | S & F in repair prelaminated particle board 18/19 mm thick, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work all as specified and directed. |
| 7 | S&F in repair stainless steel daddu kabja for kitchen/bedroom cupboards all as specified and directed. |
| 8 | S&F Continuous (Piano) hinges SS 36 mm width of flaps (when open) complete all as specifed and directed . |
| 9 | S&F magnetic catches with steel body ‘H’ type, fixed to shutter complete all as specifed and directed. |
| 10 | S & F in repair stainless steel butt hinges/handle for cupboards or wardrobe all as specified. |
| 11 | Providing and fixing modular kitchen carcasses using 18mm thick BWP Plywood (IS:710) for sides, base and shelves. All exposed edges to be sealed with 2mm PVC edge banding tape using hot-melt glue. Inner surfaces all as specified and directed. |
| 12 | Providing and fixing modular kitchen carcasses using 9mm thick BWP Plywood (IS:710) for back and top. All exposed edges to be sealed with 2mm PVC edge banding tape using hot-melt glue. Inner surfaces all as specified and directed. |
| 13 | Providing and fixing 0.80mm thick Decorative laminate type 1 of surface finish, colour and pattern as approved, fixed with water-resistant synthetic resin adhesive (D3 grade) all as specified and directed.. |
| 14 | Providing and fixing cabinet shutters made of 18mm BWP Plywood finished with 1.5mm thick high-gloss Acrylic Laminates sheet with a 6H anti-scratch surface on the exterior and 0.8mm on the interior (to be fixed with water-resistant synthetic resin adhesive (D3 grade).). All exposed edges to be sealed with 2mm PVC edge banding tape using hot-melt glue. Inner surfaces |
| 15 | S&F Cargo Cutlery Basket of size 536 x 500x 94 front panel precise adjustment with fascia parts Wire Basket Finish- Chrome Plated complete with Quadro Channel and Respective Clamps for channels all as specified and directed. |
| 16 | S&F double walled steel drawer(Tandem) with railing, height 144 mm, 520 mm (30 Kg load capacity) Full Extn. Integrated Silent system (soft close), powder coated complete set with quadro V6 runner and clamps all as specified and directed. |
| 17 | S&F Stainless Steel Thali/Plate Inlets Basket Supplied with clamps & side holder-CP Thali/Plate 900(W) x 520(D) x 360(H) mm complete with quadro V6 runner and clamps all as specified and directed. |
| 18 | S&F Wicker Baskets, With wooden frame and integrated handle moulding with Beech Runner-320x500x120 (Cabinet width 400 mm) with Beech Rail all as specified and directed. |
| 19 | S&F Stainless Steel Chrome plated Multi-purpose Plain Wire Basket 536 x 500 x 200) (21’’ x 20’’ x 8’’), 3 Dimensional Front Facia adjustment complete with quadro V6 runner and clamps all as specified and directed. |
| 20 | S&F Sturdy stainless steel Bottle Pull out - 2 tier -For Cabinet width 200 mm with Quadro Left +Right Channel full Extn.Silent System 450 mm 30 kg and Quadro Clamps complete |
| 21 | S&F High Grade Stainless Steel Open-Top Bin Holder/Dust Bin Holder/Modular Kitchen Fixture (Dia 10 Inches-Sliver) all as specified and directed. |
| 22 | S&F Auto Closing Clip-on Soft Close Hinges for 14-25 mm thick doors; Opening angle 105 with Eccentric Mounting Plate all as specified and directed. |
| 23 | S&F aluminium profile handle ss finished Profile height 38mm for 19 mmthickness all as specified and directed. |
| 24 | S&F end cap for profile handle all as specified and directed. |
| 25 | S&F Push to Open cabinet lift (gas spring) all as specified and directed. |
| 26 | Taking down cement plaster of any description on brick or stone walls or from concrete surface incl racking out joints hacking for key scrubbing with water etc all as specified. |
| 27 | M&L for Rendering 15 mm thick cement plaster in CM 1:4 on fair faces of brick/concrete surfaces finished fair and even, mixed wth water proofing compound admixture (if directed) as per manufacturer's instruction, complete all as specified and directed.Note :- WPC will measuered and paid separatly under relevant item of schedule. |
| 28 | Supply only liquid Water proofing compound all as specified and directed.. |
| 29 | Material & Labour for preparation of new surfaces of plastered walls and applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over and including a coat of 1.5 mm thick white wall care putty (premium quality) over plastered surfaces of walls to prepare the surface even and smooth complete all as specified . . |
| 30 | Complete removal of existing treatment and applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over and including a coat of 1.5 mm thick white wall care putty (premium quality) over plastered surfaces of walls to prepare the surface even and smooth complete all as specified . . |
| 31 | M&L for rendering 15 mm thick in CM 1:6 on other fair faces of brick work surfaces finished fair and even complete all as specified. |
| 32 | Material & Labour for preparation of new surfaces of plastered walls and applying Two coats of Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. over and including a coat of primer and 1.5 mm thick white wall care putty (premium quality) over plastered surfaces of walls to prepare the surface even and smooth complete all as specified . |
| 33 | Material & Labour for complete removal of existing treatment, preparation of surfaces of plastered walls and applying Two coats of Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. over and including a coat of primer and 1.5 mm thick white wall care putty (premium quality) over plastered surfaces of walls to prepare the surface even and smooth complete all as specified . . |
| 34 | M & L for 5 mm thick cement plaster in CM (1:3) on ceiling surfaces and finishing the surface fair and even complete all as directed by Engr-in-Charge. |
| 35 | Material & Labour for preparation of new surfaces of plastered ceiling and applying Two coats of Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. over and including a coat of primer and 1.5 mm thick white wall care putty (premium quality) over plastered surfaces of walls to prepare the surface even and smooth complete all as specified . . |
| 36 | Material & Labour for complete removal of existing treatment, preparation of surfaces of plastered ceiling and applying Two coats of Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. over and including a coat of primer and 1.5 mm thick white wall care putty (premium quality) over plastered surfaces of walls to prepare the surface even and smooth complete all as specified . . |
| 37 | Providing and applying two-component, solvent-free epoxy-based protective coating (of approved make like Dr. Fixit, Fosroc, or Sika) having a minimum dry film thickness (DFT) of 300 microns in two coats. Surface preparation includes mechanical grinding, cleaning, and ensuring a moisture content below 4%. All work to be executed as per manufacturer's specifications and directed by the Engineer-in-Charge. |
| 38 | Demolition of brick work built in CM including all quions, arches, pillars etc, but excluding ashlar facings, dressed stonework and precast concrete articles including removal of the rubbish off the premises all as specified and directed. |
| 39 | M&L brick work with fly ash old sized bricks straight or curved on plan exc 6 m mean radius build in CM 1:6 all as specified as directed. |
| 40 | M&L for brickwork with fly ash old size bricks, straight or curved on plan exc 6m mean radius for manholes/septic tank/soak well etc built in CM (1:4) complete all as specified and directed |
| 41 | M&L for brick work with flyash bricks straight or curve on plan to any radius in half bricks thick walls, built in cement mortar (1:4) complete all as specified and directed. |
| 42 | M & L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips.all as specified and directed. |
| 43 | S&F TMT reinforcement bar, conforming to Fe-500, 6mm to 8mm dia cut to length , bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire ( annealed) not less than 0.9mm dia or securing with chips.all as specified and directed. |
| 44 | S&F TMT reinforcement bar, conforming to Fe-500, 5mm dia and upto and including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends as binding with and including mild steel wire (Annealed) not less than 0.9mm dia or securing with clips all as specified. |
| 45 | M & L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) all as specified and directed. |
| 46 | Demolition of RCC(other than ground floor) pillar, beams landing, chajjas, slab shelves & similar suspended work (reinforcement cut as required to facilitate demolition) and removing unseviceable material complete all as specified and directed |
| 47 | M&L for RCC 1:1.5:3 type A1 (20 mm graded stone aggregate) nominal mix in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified and directed by the Eng-in-charge. |
| 48 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises.all as specified and directed. |
| 49 | M & L for light shade vitrified ceramic tiles 10mm thick (square /rectangular ) polished , area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc set and jointed in neat cement slurry and pointed flush in white or colour cement with pigment over and including 15mm thick cement mortar 1:6 screed bed in double charge complete all as specified. |
| 50 | M&L Non Skid coloured ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cemeent to match and including over screed bed or bedding layer of mortar 15 mm thick laying floor finished in CM 1:6 complete all as specified and directed. |
| 51 | M&L Non Skid coloured ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cemeent to match and including over screed bed or bedding layer of mortar 15 mm thick laying floor finished in CM 1:6 complete all as specified and directed. |
| 52 | M&L for Glazed ceramic wall tiles in vertical surface 600x1200x10mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the colour of tiles including C:M (1:3) back coat of mortar 10 mm thick for laying skirting/dado's wall tiles complete all as speciified and directed. |
| 53 | M&L for Glazed ceramic tiles in vertical surface 450x 350x 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the colour of tiles including C:M (1:3) back coat of mortar 10 mm thick for laying skirting/dado's wall tiles complete all as speciified and directed. |
| 54 | Dismantling Stone slabs and tiles of any description or thickness in floors, aprons etc all as directed. |
| 55 | M&L for 18-20mm thick Granite work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to matchwith shade of granite all as specified and directed. |
| 56 | M&L for 18 mm thick green marble (table rubbed and polished) in steps, jambs, pillars, window cills, bathroom corners cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with green marble shade complete all as spd and directed. |
| 57 | Taking down chowkats or frames with shutter w/o taking off shutter from the frame n exc 1.5 Sqm each incl cutting holes for taking out hold fast or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt.) all as specified and directed by Engr-in-charge. |
| 58 | Taking down chowkats or frames with shutter w/o taking off shutter from the frame exc 1.5 Sqm & n. exe 4 Sqm each incl cutting holes for taking out hold fast or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt.) all as specified and directed By Engr-in-charge. |
| 59 | Taking down shutters of any description n. exc 1 sq. m each complete all as specified and directed by Engineer-in-Charge |
| 60 | S&F in repair factory made single extruded WPC ( Wood polymer composite ) solid door/window and others frames/chowkhat of size 50x125 mm double shutter comprising of virgin PVC polymer of K value 58-60 (Suspension Grade ), calcium carbonate and natural fibres and non toxic additives fabricated with mitred joints after applying PVC solvent cement and screwed with full body threaded star headed SS Screws having minimum frame density of 750kg/cum and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engg-in-charge. |
| 61 | S&F in repair for providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of EngineerIn- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately), complete all as specified. |
| 62 | S&F in repair factory made single extruded WPC ( Wood polymer composite ) 30 mm thick glazed and skeleton panelled door shutter comprising of virgin PVC polymer of K value 58-60 (Suspension Grade ), calcium carbonate and natural fibres and non toxic additives having minimum density of 650kg/cum and with property of being termite/borerproof,water/moisture proof and fire retardent and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws complete as per direction of Engg-in-charge. |
| 63 | S & F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing. all as specified and directed. |
| 64 | S & F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing. all as specified and directed. |
| 65 | Supply and fixing factory made uPVC white colour Casement door with 3D hinges made of (big series) frame 67 x 64 mm & sash 67 x 110 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of door upto 2.00 sqm) comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws, etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality complete all as specified and directed by Engineer-inCharge. (Glass shall be paid separately) |
| 66 | Supply and fixing factory made uPVC white colour Three track three panels glazed sliding door made of (big series) frame 116 x 45 mm & sash 46 x 82 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead/ double glazing bead of appropriate dimension. (Area of door above 5.00 sqm) comprising of uPVC multi-chambered frame, with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension uPVC extruded glazing beads, uPVC extruded interlock and uPVC extruded Inline sash adaptor (if required), EPDM gasket, wool pile, zinc alloy (white powder coated) handle with key on one side of extreme panels along with zinc plated mild steel multi point locking having transmission gear with keeps, zinc alloy (white powder coated) cresent lock (if required), stainless steel (SS 304 grade) body with adjustable double nylon rollers (weight bearing capacity to be 120 kg). G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. (Glass or wiremesh shall be paid separately). |
| 67 | Supply and fixing factory made uPVC white colour Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) upto 1.50m height made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) comprising of uPVC multichambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. (Glass or wiremesh shall be paids separately). Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. all as specified and directed. |
| 68 | M&L sheet glass 4.8 mm thick ordinary quality and glazing with oil putty and pin in square exc 0.50 sqm in each pan complete as directed. |
| 69 | M&L Sheet glass, 3 mm ordinary quality and glazing, obscured or frosted, on one side in square n exc 0.5 sq. m in each pane complete as directed. |
| 70 | S&F in repair stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned stacks or galvanised wire staples, complete all as specified and as directed. |
| 71 | S & F Floor door stopper 150 mm long of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor. all as specified and directed. |
| 72 | S & F 300 mm long Aluminium alloy, anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast Aluminium alloy and fixed. all as specified and directed. |
| 73 | S&F powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including aluminium snap beading for glazing/ paneling, all complete as per architectural drawings and the directions of Engineer-in-Charge. |
| 74 | S & F powder coated Anodised aluminium window shutters, sliding type without sash bars, (minimum thickness of powder coating 50 micron) for three track shutters of windows & ventilators aluminium sections weighing 0.55 kg/m including necessary joining cleats , Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, anodised aluminium fittings suitaible etc all complete as per architectural drawings and the directions of Engineer-in-charge. |
| 75 | S&F in repairs, door closer aluminium body, hydrailically regulated, designation No.2, universal type, suitable for door shutters and weight between 36 to 60 kg and fixed complete all as specified and as directed. |
| 76 | M & L for aluminium snake guard fixed in aluminium doors complete all as spd and directed |
| 77 | M&L for framed work such as grills etc with ends of bars shouldered nd or riveed or forged into spike, framed guard bars and similar work conforming to Fe 290 Gde-E-165 complete all as specified and directed. |
| 78 | M&L for preparing of new steel & iron surfaces of any description, not otherwise described, over 10cm width or girth and applying two coats of synthetic enameled paint over a coat of Red oxide zinc chrome primer zinc chrome complete all as specified and as directed. |
| 79 | M & L for repairs to crack portion with jacketting technique, taking down the existing plaster up to the brick wall surface of min 200mm wide, cleaning the loose particles on surface of brick work along the length of the crack and filling the gap/crack area with PCC 1:1.5:3 type A0 using 12.5mm aggregate up to brick surface and inserting the welded mesh of size 25X25X2mm along the crack on both sides of the wall surface fixed with, drilling holes 10mm dia on either side of the crack by means of drilling mechanism through the full width of the wall @25cm c/c and insert 8/10mm dia rod in the drilled holes, welded with horizontal rod to with-hold the welded mesh and applying grit plaster 1:1:2 using 4mm and down aggregate finished even and smooth without using extra cement. Note: reinforcement and welded mesh will be measured and paid separately. all as specified and directed. |
| 80 | M&L for 75 mm thick cement concrete M10 (Nominal Mix) with 40mm graded crushed aggregate finished even and fair laid to a slope of 1 in 12, laid in alternate bays, each bay not exceeding 3 m length with joint filled with bituminous mastic filling comprising a mixture of 1 part of heated Industrial bitumen 85/25 grade and two parts of heated sand as in plinth protection complete all as specified |
| 81 | Material & Labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels , plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement, complete all as specified and directed. |
| 82 | S & F in repair 100 mm size Stainless Steel Hinges all as specified and directed. |
| 83 | S & F in repair 75 mm size Stainless Steel Hinges all as specified and directed. |
| 84 | S&F 200 mm long Aluminium, anodised, barrel tower bolt of extruded section. all as specified and directed. |
| 85 | S&F aluminium handles, cast type, anodised 150mm long. all as specified and directed. |
| 86 | Taking down steel tubing having bore of pipe 15 mm and connections, including cleaning for refixing or removal to store all as specified and directed. |
| 87 | Taking down steel tubing having bore of pipe 20 mm and connections, including cleaning for refixing or removal to store all as specified and directed. |
| 88 | S&F 16 mm outer dia medium grade CPVC, SDR 11 & plain CPVC SDR 11 with all fittings (brass inside the fittings) and fixed complete to walls and ceiling or laid in floors complete all as specified and directed. |
| 89 | S&F 20 mm outer dia medium grade CPVC, SDR 11 & plain CPVC SDR 11 with all fittings (brass inside the fittings) and fixed complete to walls and ceiling or laid in floors complete all as specified and directed. |
| 90 | S & F gate valves 20 mm bore dia with iron wheel head, screwed both ends for iron pipe and fixed, complete all as specified and directed. |
| 91 | S&F 15mm bore CP Basin Mixer without pop up chromium plated for mixing hot & cold water screwed down for GI/CPVC pipe and fixed. Make : Jaquar Cat Part No FLR-CHR-5191N or Equivalent all as specified and directed. |
| 92 | S&F in repair 15mm bore Brass CP Wall Mixer for mixing hot & cold water screwed down for iron pipe and fixed. all as specified and directed. |
| 93 | Supply and fix in repair bib taps of 15mm bore fancy type, chromium plated cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for brass ferrule complete all as specified and directed. |
| 94 | S&F in repair Pillar taps (Swan Neck) wall mounted fancy type 15mm bore cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed, complete all as specified and directed. |
| 95 | S&F in repair sink with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes including bedding in cement morter to dwarft wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410 mm x 330mm x 160mm. all as specified and directed. |
| 96 | S & F vitreous china premium/ 1st quality wash down water closet wall hung EWC white/ ivory/ off white (closed pattern including all necessary accessories like rag bolts/ gel gasket etc.) including flush pipe of polyethelene of low or density or PVC 32 mm dia for low level flushing cistern, plastic seat cover and 10 ltr capacity PVC valveless syphonic action type flushing cistern low level white with inlet, ball valve, float and handle including brackets, etc complete all as specified and directed. Note : Fixing of wall hung EWC and flushing cistern shall be done all as per manufacturer's instructions. all as specified and directed. |
| 97 | M&L in repair vitreous china wash basin, oval type counter top shape of size 550x460mm laid over stone slab of approved size including necessary cutting including 32mm dia chromium plated waste coupling and waste pipe complete all as specified and directed. |
| 98 | S&F in repair vitreous China wash basin, white, pedestal pattern, size 550X400 mm including cutting for pinning in ends of brackets,complete.all as specified and directed. |
| 99 | S & F in repairs vitreous china squatting pan, 'Orissa\\" pattern, size 580 mm X 440 mm white with ‘P’ or ‘S” trap, front or back inlet and integral foot rests, any pattern and including fixing , connector to flush pipe, lime concrete bedding and making connections to flush pipe, connector to branch pipe and anti syphonage pipes etc. including sealing the joints and making leak proof using sealant complete all as specified and as directed by Engineer-in-Charge. |
| 100 | S & F 32 mm dia Bottle trap of CP having minimum water seal of 25 mm (Minimum weight 32mm-260gms/ 40mm-270 gms). Make : Jaquar Cat No ALD-769L or Prayag Cat No BEA-29 or Cera Cat No F-8060401. all as specified and directed. |
| 101 | S & F in repairs PVC valve less, syphonic action type low level flushing cistern (10 ltrs capacity), white with inlet ball valve float and handle including brackets all as specified and directed. |
| 102 | S&F in repair PVC waste pipe 32mm dia for wash basin and sink 01 mtr to 3 mtr as per tequred with cap all as specified and directed. |
| 103 | S&F in repair 32 mm bore Waste coupling of CP (half or full threaded) (Minimum weight 32mm45gms/40mm-60 gms all as specified and directed. |
| 104 | S&F in repair PVC connection 15 mm size PTMT nuts of length ength 600 mm complete all as specified and directed |
| 105 | S&F in repair soap dish vitreous china white size 160x160x90mm approx all as directed by Engineer -in-Charge |
| 106 | S&F in repair toilet paper holder, vitreous china box type, coloured fixed to wall with chromium plated brass screws complete all as specified and directed |
| 107 | S&F 15mm bore , chromium plated cast copper alloy 2-in-1 bib cock tap, screwed down,for iron pipe or for brass ferrule complete all as specified and directed. |
| 108 | S&F in repair angle/stop valve of 15mm bore , chromium plated with long shank and cup concealed type cast copper alloy, screwed down, high pressure, with crutch handle, screwed both ends for brass ferrule complete all as specified and directed. |
| 109 | S&F in repair grating square 100mm size of CP (minimum weight 100 gms) complete all as specified and directed |
| 110 | S&F grating square with waste hole 100mm size of CP(minimum 100 gms). all as specified and directed. |
| 111 | S&F in repair 125mm Brass Chromium Plated shower rose with or without swivel joints, any size, including fixing to steel pipe or union all as specified and directed. |
| 112 | S & F 8mm thick single piece fancy type designed bevelled edge of mirror n. exc 1.80 sqm selected quality glass, mounted om 6 Nos stainless steel screws and fixed to wall with chromium plated brass screws and cup with LED light embedded in morror complete all as specified and directed. |
| 113 | S&F in repair health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified |
| 114 | S&F in repair MS PVC coated drepery rods of 25 mm dia of PVC coated in curtain rods. all as specified and directed. |
| 115 | S & F MS PVC sheeted/power coated bracket size 150mm made to shape suitable for holding curtain/drapery of rod of 25mm dia fixed with PVC rawl plugs and MS steel screws complete all as directed by Engr-in-Charge and as per approved sample kept in AGE B/R 1 office for single/double rod system. all as specified and directed. |
| 116 | S & F for coloured conical end balls dia not less then 50mm and PVC coated made to shape suitable for fixing as end of curtain/dropery rods complete all as directed Engr-in-Charge and as per approved sample kept in AGE B/R 1 office.all as specified and directed. |
| 117 | S&F for flash touch free infrared stainless steel hand dryer. all as specified and directed. |
| 118 | S & F in repair for Bathroom cabinet Mirror size 622mmX422 mm wall Mounted, Shape Rectangular fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed. all as specified and directed. |
| 119 | S&F for chromium plated Towel Rack 600mm Long with Lower Hangers with fixing arrangement complete all as specified and as directed. |
| 120 | S&F in repair for chromium plated Towel Ring Round with fixing arrangement complete all as specified and as directed. |
| 121 | S & F in repairs for Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long, complete all as specified and directed. |
| 122 | S&F in repair for CP Corner Glass Shelf (with Bracket) with fixing arrangement complete all as specified and as directed. |
| 123 | S & F in repair stainless steel kitchen plate rack made out of 0.63mm thick stainless steel of size 750x600mm including screws complete all as directed. |
| 124 | M & L 75 mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement all as specified and directed. |
| 125 | Taking down rain water pipes (any size or pattern) , including all fittings and removal off the site complete all as specified and directed. |
| 126 | S & F in repair 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed to wall with clamps and jointed complete all as specified and as directed by EIC. |
| 127 | S & F in repair 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed to wall with clamps and jointed complete all as specified and as directed by EIC. |
| 128 | S&F in repair 110mm bore PVC (SWR) bends any radiuswith access door complete all as specified and as directed by EIC. |
| 129 | S&F in repair 75mm bore PVC (SWR) bends any radius with access door complete all as specified and as directed by EIC. |
| 130 | S & F 75 mm PVC (SWR) junction single, (Single T) equal or unequal |
| 131 | S&F PVC (SWR) vent cowl 110 mm bore. |
| 132 | Taking down existing roof felt including plaster of any description carefully from existing roof /parapet without disturbing wall surface and removing the same at a distance exc 1.5 Km complete all as specified and as directed. including rwashing down with water to remove dust, foreign items complete all as specified and directed complete all as specified and directed |
| 133 | M&L for 40 mm thick average PCC 1:2:4 type B-0 (12.5 mm graded aggregate) as in padding concrete on roof all as directed by Engineer- in-Charge. |
| 134 | M&L for rendering 10mm thick on fair faces on roof surfaces of concrete in Cement Mortar 1:3 mixing with WPC finished even and smooth without using extra cement and WPC complete all as specified and directed. (Note :- WPC will measuered and paid separatly under relevant item of schedule.) |
| 135 | M&L for providing water proofing treatment with a layer of APP based polymeric membrane 3mm thick minimum weighing 3.60kg/sqm reinforced with polyster non wove fabric (wt. not less than 160 gms/sqm) shall be applied over one coat of cold bituminous primer @ 0.40 ltr/sqm (membrane shall be laid using butane torch sealing all joints etc, complete all as spd and directed. (Note :- The over lap shall be of minimum 75mm in longitudinal direction and 100mm on transverse direction ) |
| 136 | M&L for one coat of aluminium paint over APP membrane complete all as specified and directed. |
| 137 | Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including nainital or similar pattern roof coverings complete all as specified and directed. |
| 138 | Dismantling wrought iron or mild steel work of any description not otherwise provided, for rusted members of steel trusses/ purlins, complete all as specified and directed |
| 139 | S&F for stairs (framed) including stringers, treades, landing, balusters, hand rails etc. including cleats, brackets,etc. of Fe 410 -W (GdeE- 250) quality A, complete all as specified and directed. |
| 140 | S & F Roof trusses (framed) of angle iron members trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee,angle,channel or flat sections) including distance pieces, cleats etc complete all as specified. |
| 141 | M & L for pre-painted hot-dip aluminium-zinc alloy metallic coated of any profile steel sheet corresponding to IS 15965:2012 of durability class 3, atmospheric classification category 3, coating class AZ150, 0.50 mm thick, of an approved colour and having yield strength of 550 MPa as in roof covering fixed with self tapping screws as specified up to anyheight including all necessary scaffolding and safety measures complete all as specified and directed |
| 142 | M & L for pre-painted hot-dip aluminium-zinc alloy metallic coated plain steel sheet as per IS 15965:2012 of durability class 3, atmospheric classification category 3, coating class AZ150, 0.50 mm thick, of an approved colour and having yield strength of 550 MPa as in ridge/ valley/ gutter fixed with self tapping screws as specified any height Mtr height including all necessary scaffolding and safety measures complete all as specified and directed |
| 143 | M&L for RCC precast cement concrete type B-1, 1:2:4 (using 20 mm graded stone aggregate)as in cover slab for manholes and similar article with plain face set in CM (1:4) complete all as specified and directed (Note: Reinforcement will be measured and paid separately) |
| 144 | M& L for PCC type D2 1:4:8 using 40 mm graded aggregate in foundations, fillings and mass concrete. |
| 145 | Material and labour for cement concrete bed to drain pipe for 150mm bore of pipe including forming cradles in Cement concrete 1:3:6 Type C2 complete all as specifiedand and as directed. |
| 146 | Supplying and laying of PVC underground drainage sewer system pipe bearing 160 mm dia SN 4 including jointing with couplar, bend tee as per site requirement complete laid in trenches or floors complete all as specified and directed. |
| 147 | Taking down carefully aluminium conductor point wiring (light,fan,socket or power) complete including fittings such as switches,ceiling roses, pendants, regulators ,sockets etc. and removing (except those to be reused shall be kept in safe custody at the site ) and making good disturbed surfaces of walls, floors etc.to match with the existing complete all as specified. Please Enable Macros to View BoQ information |
| 148 | Taking down carefully aluminium conductor point wiring (light,fan,socket or power) complete including fittings such as switches,ceiling roses, pendants, regulators ,sockets etc. and removing (except those to be reused shall be kept in safe custody at the site ) and making good disturbed surfaces of walls, floors etc.to match with the existing complete all as specified. Please Enable Macros to View BoQ information |
