|
| 1 | Removal of rubbish,earth etc. from the working site and disposal of the same beyond the compound, in conformity with the Municipal / Corporation Rules for such disposal, loading into truck and cleaning the site in all respect as per direction of Engineer in charge. |
| 2 | Labour for taking out door and window frame including shutter for repair or replacement of different parts of the frame & refixing the same including mending good all damaes complete. Upto area 2.5 Sq.m |
| 3 | Taking out shutter of door and window, dismantling by parts (for repair or replacement of damaged parts) , reassembling and refitting and rehanging same with old fittings but with new screws as necessary. |
| 4 | Clearing compound premises of shurbs, plants, jungles etc.by cutting and removing as directed |
| 5 | Cleaning the concrete surface by removing dirt and debris, marking defective locations and removing loose concrete by careful stripping untill hard surface is exposed, cutting the concrete to regular shape, wire brushing the exposed surface and removing debris from site complete as per direction of the Engineer - in - Charge. |
| 6 | 250 mm thick Brick work with Fly Ash Bricks (250mmx125mmx75mm) as per IS 12894:2002 in cement mortar (1:4). In foundation and plinth |
| 7 | In superstructure, ground floor |
| 8 | Hire and labour charges for shuttering with centering and necessary staging upto 4 m using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, beams and columns, lintels curved or straight including fitting, fixing and striking out after completion of works (upto roof of ground floor) Above 30 mm & upto 37 mm thick wooden shuttering as per decision & direction of Engineer-In-Charge. In Ground floor |
| 9 | Ordinary Cement concrete (mix 1:1.5:3) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement if any, in ground floor as per relevant IS codes. In ground floor. |
| 10 | Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every intersection, complete as per drawing and direction.For works in foundation and upto roof of ground floor/upto 4 m. JSW/JSPL/SHYAM/ RMB/BMASL/ELECROSTEEL/SSL, In ground floor. |
| 11 | Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary With 1:6 cement mortar 20 mm thick plaster,In ground floor |
| 12 | ,In 1st floor |
| 13 | With 1:4 cement mortar 10 mm thick plaster,In ground floor |
| 14 | In 1st floor |
| 15 | Artificial stone in floor, dado, staircase etc with cement concrete (1:2:4) with stone chips, laid in panels as directed with topping made with ordinary or white cement (as necessary) and marble dust in proportion (1:2) including smooth finishing and rounding off corners including raking out joints or roughening of concrete surface and application of cement slurry before flooring works using cement @ 1.75 kg/sq.m all complete including all materials and labour. In ground floor. 3 mm. thick topping (High polishing grinding on this item is not permitted with ordinary cement). Using grey cement. 25 mm. thick. |
| 16 | Supplying, fitting & fixing 1st quality Ceramic tiles in walls and floors to match with the existing work & 4 nos. of key stones (10mm) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles including roughening of concrete surface, if necessary or by synthetic adhesive & grout materials etc.FloorWith Sand Cement Mortar (1:4) 20 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m & joint filling using white cement slurry @ 0.20kg/Sq.m.Area of each tile upto 0.09 Sq.m. Coloured decorative. In Ground Floor. |
| 17 | In 1st floor |
| 18 | Wall With Sand Cement Mortar (1:3) 15 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m & joint filling using white cement slurry @ 0.20kg/Sq.m. Area of each tile above 0.09 Sq.m. Coloured decorative, In Ground Floor. |
| 19 | In 1st floor |
| 20 | Supplying and laying true to line and level Double Charge Vitrified Tiles of approved brand conforming to IS 15622: 2006 (Group B I a) and tested as per IS 13630:2006 (relevant parts) [Non-modular sizes for tiles with Water Absorption (av.) ≤ 0.08 %] in floor, skirting etc. using polymerised adhesive of 6mm thick layer applied directly over finished artificial stone floor/Mosaic etc without any backing course and joints grouted with admixture of white epoxy grout materials of approved brand including spacer -2mm as directed and removal of wax coating of top surface of tiles with warm water and polishing the tiles using soft and dry cloth upto mirror finish complete including the cost of materials,Iabour and all other incidental charges complete as per direction of Engineerin- Charge. (Note: This work should not be executed without specific permission of Superintending Engineer : ln Ground FIoor:(size not Iess than 600mmX 600 mm X 9.5mm thick |
| 21 | Supplying bubble free float glass of approved make and brand conforming to IS: 2835-1987. 4mm thick coloured / tinted / smoke glass. |
| 22 | Easing, oiling and adjusting the steel shutters including scraping all members and fitting so as to make the shutters easily operable (no extra payment will be made for taking out and fixing glass, if necessary).(Each means a pair of shutter in a frame) |
| 23 | Renewing hinge of steel shutter including taking out old one by cutting and fixing new hinges by welding and mending good damages complete. |
| 24 | Supplying best Indian sheet glass panes set in putty and fitted and fixed with nails and putty complete. (In all floors for internal wall & upto 6 m height for external wall) : 4 mm thick |
| 25 | Extra for fixing glass panes in steel window. |
| 26 | Renewing worn out putty of glass panes : Panes not exceeding 0.2 Sq.m |
| 27 | Wood work in door and window frame fitted and fixed in position complete including a protective coat of painting at the contact surface of the frame exluding cost of concrete, Iron Butt Hinges and M.S clamps. Sal : Malayasian: In ground Floor. |
| 28 | Styles and rails of wooden shutters fitted and fixed complete. (Payment to be made on area of new work only).35mm Thick shutter.Sishu, Gamar, Champ,Badam,Bhola, Mogra, Hallak. |
| 29 | Panel (made of single plank) of door and window shutters to design as directed: In Ground Floor (Payment to be made on area of exposed new work). (In case of non-supply of single plank penal rate of reduction to a maximum of 30% will be made).19mm thick panel of 30cm to 45cm width. Sishu, Gamar, Champ,Badam,Bhola, Mogra, Hallak. |
| 30 | Supplying, fitting and fixing M.S. Clamp for fixing door and window frame made of flat bent bar, end bifucated, fixed in cement concrete with stone chips (4:2:1) fitted and fixed complete as per direction. 40 mm. x 6 mm., 200 mm. length |
| 31 | Iron butt hinges of approved quality fitted and fixed with steel screws, with ISI mark. 100mm. X 58mm. X 1.90mm. |
| 32 | Anodised aluminium Aldrop / Sliding bolts of approved quality manufactured from extruded section conforming to I.S. specification (I.S. 2681/66) fitted and fixed complete. 300 mm long x 19 mm dia bolt. |
| 33 | Anodised aluminium barrel / tower / socket bolt (full covered) of approved manufactured from extruded section conforming to I.S. 204/74 fitted and fixed with cadmium plated screws: 300mm long x 10mm dia. bolt. |
| 34 | 150mm long x 10mm dia. bolt. |
| 35 | Anodised aluminium D-type handle of approved quality manufactured from extruded section conforming to I.S. specification (I.S. 230/72) fitted and fixed complete. With continuous plate base hexagonal/round rod. 150 mm grip x 10 mm dia. Rod |
| 36 | Supplying ,fitting and fixing hinge cleat in position excluding the cost hinge and other fiffitngs . with 75mm iron Butt-hinge . Sal : Malayasian |
| 37 | Supplying, fitting & fixing 125mm long wooden buffer block Sal : Malayasian |
| 38 | M.S.or W.I. Ornamental grill of approved design joints continuously welded with M.S, W.I. Flats and bars of windows, railing etc. fitted and fixed with necessary screws and lugs in ground floor. : Grill weighing above 10 Kg./sq.mtr and up to 16 Kg./sq. mtr. : In ground floor. |
| 39 | Roof treatment by application of non toxic polyurethane modified acrylic based single component (P U Roof Coat) solvent free,cold applied polyurethane modified elastomeric waterproofing membrane with excellant UV resistant capasity as per ASTM D6083[ a water based100% acrylic elastomeric emulsion polymer latex coating used as protective coating for roofs ] after preparing the surface of cleaning and repairing the roof cracks by cement & sand mortar(1:4),preferably with antishrinkage morter(to be paid seperately) if any ,apply two coats along with a priming coat (two coats of P U Roof Coat and one coat of primer coat compitable with main product as per manufacturers specification )and reinforced with or without 20 gsm Geotextile Fleece,including the cost of primer coat and base preparation tools and plants but excluding the cost of scaffolding and stagging complete as per direction of Engineer-in-charge.(Note : If Geotextile Fleece not used, the rate would be reduced by Rs. 5/ per Sqm.) |
| 40 | Removing old scales, blisters etc. of interior surface of walls,ceiling by scraping etc. and preparing smooth and even surface with rendering or cement mortar (1:2) (as necessary), to make the surface suitable for receiving distemper. (Payment against this item will be made only when this has been done on the specific direction of the Engineer-in-charge). |
| 41 | Acrylic Distemper to interior wall, ceiling with a coat of solvent based interior grade acrylic primer (as per manufacturer's specification) including cleaning and smoothning of surface. Two Coats One Coat Water based interior grade Acrylic Primer. |
| 42 | Applying Exterior grade Acrylic primer of approved quality and brand on plastered or cencrete surface old or new surface to receive decorative textured(matt finish) or smooth finish acrylic exterior emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer's specification and as per direction of the EIC. One coats In ground floor |
| 43 | In 1st floor |
| 44 | In 2nd floor |
| 45 | Protective and Decorative Acrylic exterior emulsion paint of approved quality, as per manufacturer's specification and as per direction of Engineer-in-Charge to be applied over acrylic primer as required. The rate includes cost of material, labour, scaffolding and all incidental charges but excluding the cost of primer. Super Protective 100% Acrylic Emulsion. In ground floor |
| 46 | In 1st floor |
| 47 | In 2nd floor |
| 48 | Painting with ready mixed red lead paint of approved make and brand : Two coats |
| 49 | Priming one coat on timber or plastered surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc. |
| 50 | Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary : On steel or other metal surface :With super gloss (hi-gloss) - Two coats (with any shade except white) |
| 51 | On timber or plastered surface : Two coats (with any shade except white) |
| 52 | Supplying, fitting & fixing UPVC pipes A- Type and fittings conforming to IS:13592-1992 with all necessary clamps nails, including making holes in walls, floor etc. cutting trenches in any soil through masonry concrete structures etc if necessary and mending good damages including joining with jointing materails (Spun Yarn, Valamoid/Bitumen/M-Seal etc) complete.UPVC Pipes:160 mm. Dia. |
| 53 | Shoe 160 mm. Dia. |
| 54 | Bend 87.5 degree 160 mm. Dia. |
| 55 | Dismantling Indian W.C. including taking out base concrete as necessary. |
| 56 | Dismantling E.P. or Anglo-Indian W.C. |
| 57 | Cleaning silt of inspection pit. |
| 58 | Dismantling urinal. |
| 59 | Removing chokage of H.C.I. or S.W. pipe with split bamboo Underground |
| 60 | Supplying, fitting and fixing PVC pipes of approved make of Schedule 80 (medium duty) conforming to ASTMD - 1785 and threaded to match with GI Pipes as per IS : 1239 (Part - I). with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, making threads,fitting, fixing etc. complete in all respect including cost of all necessary fittings as required,jointing materials and two coats of painting with approved paint in any position above ground. For Exposed Work; PVC Pipes50 mm dia. |
| 61 | 40 mm dia. |
| 62 | 15 mm |
| 63 | 25 mm |
| 64 | 32 mm |
| 65 | Compact Compact Ball Valve with SS Handle For CPVC/ UPVC Fittings. (As per ASTM D 2467, Schedule 80 50 mm |
| 66 | 40 mm |
| 67 | 32 mm |
| 68 | 25 mm |
| 69 | Supplying, fitting and fixing bib cock or stop cock.Chromium plated Bib Cock short body (Equivalent to Code No. 511 & Model - Tropical / Sumthing Special of ESSCO or similar brand). |
| 70 | Chromium plated angular Stop Cock with wall flange (Equivalent to Code No. 5053 & Model - Florentine of Jaquar or similar brand). |
| 71 | Chromium plated Stop Cock (Equivalent to Code No. 513(A) & 513(B) & Model - Tropical / Sumthing Special of ESSCO or similar brand).. |
| 72 | Supplying, fitting and fixing shower of approved brand and make. Chromium plated round shower with revolving joint 100 mm dia with rubid cleaning system (Equivalent to Code No. 542(N) & Model - Tropical / Sumthing Special of ESSCO or similar brand). |
| 73 | Supplying, fitting and fixing Flat back urinal (half stall urinal) in white vitreous chinaware of approved make in position with brass screws on 75 mm X 75 mm X 75 mm wooden blocks complete. 465mm X 355 mm X 265 mm |
| 74 | Supplying, fitting and fixing 18 mm thick marble partition slab with chawk doongri marbel square cut, both sides polished with two front corners rounded and edges polished. |
| 75 | Supplying, fitting and fixing white vitreous china best quality approved make wash basin with C.I. brackets on 75 mm X 75 mm wooden blocks, C.P. waste fittings of 32 mm dia., one approved quality brass C.P. pillar cock of 15 mm dia., C.P. chain with rubber plug of 30 mm dia., approved quality P.V.C. waste pipe with C.P. nut 32 mm dia., 900 mm long approved quality P.V.C. connection pipe with heavy brass C.P. nut including mending good all damages and painting the brackets with two coats of approved paint.630 mm X 450 mm size. |
| 76 | Supplying, fitting and fixing E.W.C. in white glazed vitreous chinaware of approved make complete in position with necessary bolts, nuts etc. : With 'P' trap (with vent) |
| 77 | Supplying, fitting and fixing Orissa pattern water closet in white glazed vitreous chinaware of approved make in position complete excluding 'P' or 'S' trap (excluding cost of concrete for fixing). 580 mm X 440 mm |
| 78 | Supplying, fitting and fixing Closet seat of approved make with lid and C.P. hinges, rubber buffer and brass screws complete. Anglo Indian Plastic (hallow type) white |
| 79 | Supplying, fitting and fixing 10 litre P.V.C. low-down cistern conforming to I.S. specification with P.V.C. fittings complete,C.I. brackets including two coats of painting to bracket etc. |
| 80 | Supplying,fitting and fixing 32 mm dia. Flush Pipe of approved make with necessary fixing materials and clamps complete.Polythene Flush Pipe |
| 81 | Supplying,fitting and fixing approved brand P.V.C. CONNECTOR white flexible, with both ends coupling with heavy brass C.P. nut, 15 mm dia. 600 mm long |
| 82 | Supplying, fitting & fixing Aluminium domical grating. 125 mm |
| 83 | Constructing Inspection pit of inside measurement 600mm X 600mm X upto 600mm (depth) with 250 mm thick 1st. class brick work in cement mortar (1:4) on all sides, bottom of the pit consisting of 100 mm thick cement concrete (1:3:6) with stone chips over a layer of jhama brick flat soling,15 mm thick (1:4) cement plaster to inside walls and out-side walls upto G.L. and 20 mm.thick (1:4) plaster to bottom of the pit, providing necessary invert with cement concrete (1:3:6) with stone chips as per direction, neat cement finishing to entire internal surfaces, top of the pit covered with 100 mm thick R.C.C. slab (1:1.5:3) with stone chips and necessary reinforcements upto 1% and shuttering including 6 mm thick cement plaster (1:4) in all external surfaces of the slab and one 560 mm dia. R.C.C. manhole cover of approved make supplied, fitted and fixed in the slab with necessary fittings, necessary earthwork in excavation in all sorts of soil, filling sides of the pit with earth and removing spoils after work complete in all respect with all costs of labour and materials. With Pakur variety.(SAIL/TATA/RINL) |
| 84 | Extra for each additional depth of 150 mm or part thereof beyond initial 600 mm depth. |
| 85 | Supply of UPVC pipes (B Type) & fittings conforming to IS-13592-1992 Single Socketed 3 Meter Length; 160 mm |
| 86 | (ii) Double Socketed 3 Meter Length; 110 mm |
| 87 | (ii) Double Socketed 1.2 Meter Length; 110 mm |
| 88 | Single Socketed 3 Meter Length; 110 mm |
| 89 | Fittings Door Tee : 110 mm |
| 90 | Bend 87.5º : 110 mm |
| 91 | Door Bend (LH) & (RH) : 110 mm |
| 92 | Pipe Clip : 110 mm |
| 93 | 110 X 110 P Trap : 75 mm |
| 94 | 110/110 S Trap |
| 95 | Labour for fitting and fixing U.P.V.C. pipes for above ground work including cost of jointing materials etc. fitting and fixing all necessary specials, cutting pipes, cutting holes in walls or R.C. floor where necessary and mending good all damages excluding the cost of masonry or concrete work, if necessary, but including the cost and fitting and fixing holder bat clamps (any floor) or for underground work including cutting trenches upto 1.5 metre and refilling the same complete as per direction of the Engineer-in-charge. (Payment will be made on centre line measurement of the total pipeline including specials. : Under ground 160 mm dia. Please Enable Macros to View BoQ information |
