|
| 1 | 'Notes: (i) Please refer Schedule 'A' Notes of tender documents. |
| 2 | Dismantling of brick or terracing tiles of single layers on roofs and removed from site complete all as specified and as directed |
| 3 | Demolition of Mud in roofs, any thickness, including plastering and leeping (whether full thicknes removed or only a part thereof) and removing the demolished material out of MD land complete all as specified and directed. |
| 4 | M&L for wire brushing and cleaning top surface of RCC roof including flashings and junction of parapets, etc.removing dirt and dust particles complete all as specified and directed. |
| 5 | M&L for cement concrete 1:3:6 type C1 using 20 mm graded aggregate as in padding over roof minimum thickness at khurra as 25 mm to maintain a slope of 1:100 complete all as specified and directed. |
| 6 | M&L for APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non woven fabric (wt. not less than 150 gms/sqm) and applying bitumen primer @ 0.30kg/sqm and lanying APP membrane on primed surface by Torch application complete all as specified and directed. |
| 7 | M&L for factory made Cement concrete tiles with grey cement and no pigment 25cm x 25cm x 22mm thick, machine pressed; set jointed and pointed in neat cement slurry in floors over roofs including 15mm thick screed bed of CM 1:6 and filling the joints with cement mortar 1:3 complete all as specified and directed. |
| 8 | M & L for PCC 1:2:4, type B-0 using 12.5mm graded stone aggregate as in roof curve, benching, mud stops, steps, coping, hold fasts and the like items slightly rounded or chamfered on the edges complete all as specified and directed. |
| 9 | Demolition of brick work or stone/boulder masonary built in cement mortor including all quoins,arches.pillars etc complete all as specified. |
| 10 | M&L Brick work with sub class 'B' bricks straight or curved on plan exceeding 6m mean radius bulit in CM 1:6 all as specified. |
| 11 | Demolition of cement concrete un -reinforced in ground floors and pavings n.exc 15cm thickness complete all as specified. |
| 12 | Roughening surfaces of old concrete floor/roof by picking, sweeping clean and washing down with water to remove dust, etc. complete all as specified. |
| 13 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing ), removing serviceable tiles to store and rubbish off the premises |
| 14 | M&L for 25 mm thick cement concrete type B-2 1:2:4 (12.5mm graded aggregate) as in floor or similar works complete all as specified and directed. |
| 15 | M&L Vitrified ceramic tiles light shade 9-10 mm thick (Square/rectanglar) area of each tile not exceeding 0.36 sqm in floors etc; set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface over and including 15 mm thick screed bed in CM 1:4 complete all as specified and directed. |
| 16 | M&L Vitrified ceramic tiles light shade 9-10mm thick as in skirting/dado etc; set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface including 10 mm thick screed bed in CM 1:4 complete all as specified and directed. |
| 17 | Machine cut kota stone slab as in flooring 18-20 mm thick, set and jointed in cement slurry over & including screed of 15 mm thick in cement mortar (1:4) and pointed in cement mixed with pigment to match the shade of slab including rubbing, cutting and mirror type granite polishing complete all as specified.Note : 1. All the edges of slabs shall be grinded/cutted at the right angle before laying, so that paper thin, smooth jointing to be obtained.2. The colour of the slabs shall be uniform. |
| 18 | M&L for machine cut kota stone slab as in skirting of 18-20 mm thick, set and jointed in cement slurry over & including screed of 10 mm thick rendering in cement mortar (1:4) and pointed in cement mixed with pigment to match the shade of slab including rubbing, cutting and mirror type polishing complete all as specified |
| 19 | M&L for non skid coloured ceramic tiles 7 to 8 mm thick (Square/ rectanglar) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc; set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface over and including 15 mm thick screed bed in CM 1:4 complete all as specified and directed. |
| 20 | M&L for ceramic glossy finish, joint free premium quality coloured tiles 600 X 300 mm and 7-8 mm thick, in any pattern of light & dark/highlighters tiles etc as approved, on vertical surfaces such as in skirting/dado etc, set and jointed in cement slurry over & including 10 mm thick rendering in cement mortar (1:4) and pointed in white cement with pigment to match the colour of tiles complete all as specified and directed. |
| 21 | Providing and Laying Premium (1st) quality straight edge, ceramic tiles exterior grade WA value between 3% to 6% , flexural strength greater than 22N/mm², scratch resistance on mohs scale greater than 4 and crazing resistance of 2 cycles in 300x300x7 to 8 mm thick in floors etc. in any shade and design/pattern of light & dark tiles etc set & jointed in neat cement slurry & incl 15 mm thick screed bed in cement mortar (1:4) pointed in matching colored polymer cement based grout to match complete all as specified and directed. |
| 22 | Taking down chowkhats or frames of any description exc 1.5 Sqm and n. exc. 4 sqm each (without taking off shutters from the frame) including cutting hole to size for receive fresh PCC of hold fast and making good the disturbed surface same complete all as specified and directed. |
| 23 | Taking down chowkhats or frames (without taking off shutters from the frame) not exc 1.5 Sqm incl cutting holes and making good reqd shape for hold fast block for new frame complete all as specified. |
| 24 | Taking down Shutters of any description exc 1 sq. m but n.exc 2 Sqm each complete all as specified and directed |
| 25 | M&L factory made Steel Window Box type factory made using ERW 'P' Section comprising Double Frame for Gauged and Glazed Skeleton Shutter jointed internally with Flat Iron 40x3mm complete including Mild Steel Tower Bolts, Hinges, Handle, Stops, Lugs including GI Steel Wire Cloth, Glazing, etc. incluidng painting two coat over a coat of primer complete all as directed. Outer Section of Frame should be 50x25mm and Inner Section should be 40x20mm, complete all as specified and as directed.NOTE :- (a) For the purpose of Measurement & Payment Double Shutter with Frame shall be considered as One Unit.(b) Cost of Iron Mongery as ordered/required at Site, GI Steel Wire Cloth will deem to be included in the Quoted Unit Rate.(c) Guard Bars are included in the Quoted Unit Rate. Spacing of 10mm Square Bar will be 10 Cm Centre to Centre.(d) Glazing shall be Measured and Paid separately under appropriate Item. |
| 26 | S&F factory made Pressed steel frames made of MS sheet of 1 mm thickness for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete as specified,size 125x60mm |
| 27 | M&L PCC 1:3:6 type C-0 in 12.5 mm graded stone aggregates hold fast filling inside frame & hold fasts etc complete all as specified |
| 28 | S&F factory made flush shutters 32mm thick ply construction, BWP confirming to IS 2202, solid core construction, with block board core and plywood face panels commercial type on both sides with 6mm thick lipping frame to match including supply and fixing following items :(a) Mild Steel Butt Hinges 100mm - 3 nos. per leaf(b) Mild Steel Tower Bolt 200mm long - 2 nos per leaf(c) Mild Steel Handles 150 mm - 2 nos. per leaf(d) Mild Steel Sliding Bolt 250 mm - 1 no. per leaf(e) Mild Steel Floor Door Stopper - 1 nos. per leaf. |
| 29 | S&F 32mm thick glazed and skelton shutters of 2nd class hard wood (factory made) open rebated and divided to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass etc size of members of shutter as specified in SSR-91 Pt-1 section 8 clause 8.20(a), kiln seasoned and chemically pressure treated all as specified including stainless steel 304 Grade wire cloth (0.36mm nominal dia of wire and average width of aperture 1.40mm) all as specified and including supply and fixing following items :(a) Mild Steel Butt Hinges 100mm - 3 Nos per leaf(b) Mild Steel Tower Bolt 200mm long - 2 Nos per leaf(c) Mild Steel Handles 150 mm - 2 Nos per leaf(d) Mild Steel Sliding Door Bolt/Aldrop 16x250mm - 1 No per leaf |
| 30 | S&F factory made Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed |
| 31 | S&F factory made solid PVC moulded door shutter with wood free EPS,28 to 30mm thick (stiles),with 2,4 or 6 raised panel design with 2mm thick moulded PVC sheet on the front face & 2mm plain colour PVC sheet on back face consisting of frame made out of MS tubes for top and bottom rails, MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and botom rail panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stils and rails with suitable PVC sheet beading and jointed together with solvent cement , includin supplying and fixing in the frme with 3 Nos stainless steel butt hinges complete all as specified and directed by Engr-in -Charge including S&F the following items:(a) Stainless steel (304 Grade) finished butt hinges 100mm-3 Nos per leaf.(b) Stainless Steel (304 Grade) Finished Tower Bolt 200mm long - 2 Nos per leaf(c) Stainless Steel (304 Grade) Finished Handles 150 mm - 2 Nos per leaf |
| 32 | M&L for two coat of synthetic enamel paint (finishing coat) over one coat of pink primer to new wooden surfaces of any description over 10 cm width or girth incl prepration of surfaces complete all as specified and directed. |
| 33 | M&L for Powder coated (Minimum thickness of powder coating 50 micron) Anodised aluminium frames and shutters for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed by Engineer-in-Charge. |
| 34 | S&F 5mm thick tinted glass for aluminium windows/doors/ventilators including EPDM gasket to render the glazing, air and water tight etc and power coated aluminium beeds 20 mm size complete. |
| 35 | S&F frosted Sheet glass 4mm thick , selected quality and glazing with oil putty or with aluminium beading in squares n exc 0.5 sq. m in each pane including preparing and disma complete all as specified. |
| 36 | S&F in stainless steel wire cloth 0.36mm normal dia of wire and average with apparture 1.40mm and fixed with tinned tacks or stainless steel wire staples complete all as specified and directed. |
| 37 | S&F for framed work such as window grills of square bars etc. with ends of bars shouldered and/or riveted, or forged into spikes and similar work conforming to Fe.290.Gde-E-165 |
| 38 | S&F powder coated aluminium butt hinges 100mm complete all as specified and directed. |
| 39 | S&F powder coated aluiminium tower bolt 150mm long complete. |
| 40 | S&F powder coated aluminium handles 100mm complete. |
| 41 | S&F powder coated aluminium hook and eye complete. |
| 42 | S&F stainless steel tubing of 25 mm dia chromium plated min. 1.0 mm wall thickness as in curtain rod complete incl S&F 02 Nos stainless steel brackets/finials fency type, stops fixed with ss screws etc all as specified & directed as in repair .Note : For the purpose of mesurement and payment running length of curtain rod only shall be considered. |
| 43 | Hacking out old broken Glass (any thickness, size, quality or description) from Wooden or Metal Frames, glazed with putty or fixed with beads, complete all as specified and as directed. |
| 44 | S&F Sheet Glass 4.0mm thick, Ordinary quality and glazing with Oil Putty in Square not exc. 0.50 Sqm in Each Pane of Steel Windows, complete all as specified and as directed. |
| 45 | M&L for taking down cement plaster on brick or stone walls/ceiling etc including raking out joints, hacking for key, scrubbing down with water etc |
| 46 | M&L Rendering 15mm thick on brick or concrete surface in Cement mortar 1:4, finishing surface w/o using extra Cement, mixed with integral liquid water proofing compound complete all as directed and specified. |
| 47 | Rendering 10 mm thick in cement mortar 1:6, on brick or concrete surfaces, trowelled to even and fair finish without using extra cement complete all as specified. |
| 48 | 5 mm thick cement plastering in cement mortar 1:3 on fair faces of concrete ceiling surfaces finished even & smooth without using extra cement complete all as specified and directed. Please Enable Macros to View BoQ information |
| 49 | 5 mm thick cement plastering in cement mortar 1:3 on fair faces of concrete ceiling surfaces finished even & smooth without using extra cement complete all as specified and directed. Please Enable Macros to View BoQ information |
