|
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. |
| 2 | All kinds of soil. |
| 3 | Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : DSR |
| 4 | All kinds of soil |
| 5 | Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia |
| 6 | Providing and laying in position cement concrete of specified gradeexcluding the cost of centering and shuttering - All work up to plinth level : |
| 7 | 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 8 | 1:5:10 (1 cement : 5 coarse sand (zone-III) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 9 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : |
| 10 | 1:1.5:3 (1 cement : 1.5 coarse sand (zone-Ill) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 11 | Centering and shuttering including strutting, propping etc. and removal of form for |
| 12 | Suspended floors, roofs, landings, balconies and accessplatform |
| 13 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. |
| 14 | Thermo-Mechanically Treated bars of grade Fe-500D or more |
| 15 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: |
| 16 | Cement mortar 1:4 (1 cement : 4 coarse sand) |
| 17 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels |
| 18 | Granite stone slab colour black, Cherry/Ruby red |
| 19 | Area of slab over 0.50 sqm |
| 20 | Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete |
| 21 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all olours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete |
| 22 | Providing and fixing ISI marked aluminium butt hinges anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with necessary screws etc. complete: |
| 23 | 100x75x4 mm |
| 24 | Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : |
| 25 | 300x16 mm |
| 26 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete |
| 27 | 300x10 mm |
| 28 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : |
| 29 | 125 mm |
| 30 | Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete. |
| 31 | Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete |
| 32 | Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge: |
| 33 | Profile B |
| 34 | Fixing with adjustable lugs with split end tail to each jamb |
| 35 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20 mmthick cement mortar 1:4(1 cement : 4coarse sand),jointing with grey cement slurry @ 3.3 kg/ sqm including grouti |
| 36 | Size of Tile 500x500 mm |
| 37 | 12 mm cement plaster finished with a floating coat of neat cement of mix : |
| 38 | 1:3 (1 cement: 3 fine sand) |
| 39 | Dismantling W.C. Pan of all sizes including disposal of dismantled materials i/c malba all complete as per directions of Engineer-in Charge. |
| 40 | Dismantling 15 to 40 mm dia G.I. pipe including stacking of dismantled pipes (within 50 metres lead) as per direction of Engineer in-Charge. |
| 41 | Internal Work- Exposed on wall |
| 42 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. |
| 43 | 15.2.1 Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) |
| 44 | Nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix) |
| 45 | Taking out existing CC interlocking paver blocks from footpath/ central verge, including removal of rubbish etc., disposal of unserviceable material to the dumping ground, for which payment shall be made separately and stacking of serviceable material within 50 metre lead as per direction of Engineer-in-Charge. |
| 46 | Laying old cement cocrete interlocking paver blocks of any design/ shape laid in required line, level, curvature, colour and pattern over and including 50 mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineerin-charge. (Old CC paver blocks shall be supplied by the department free of cost). |
| 47 | Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, |
| 48 | W.C. pan with ISI marked white solid plastic seat and lid |
| 49 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : |
| 50 | Kitchen sink without drain board |
| 51 | 610x460 mm bowl depth 200 mm |
| 52 | Providing and fixing 8 mm dia C.P. Jet with flexible tube upto 1 metre long with triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge. |
| 53 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. |
| 54 | Flexible pipe |
| 55 | 32 mm dia |
| 56 | 40 mm dia |
| 57 | Providing and fixing soil, waste and vent pipes : |
| 58 | 100 mm dia |
| 59 | Centrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS: 3989 |
| 60 | Providing and fixing heel rest sanitary bend |
| 61 | 100 mm dia |
| 62 | Sand cast iron S&S as per IS - 3989 |
| 63 | Providing and fixing collar : |
| 64 | 100 mm |
| 65 | Sand cast iron S&S pipe as per IS: 3989 |
| 66 | Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors |
| 67 | 100 mm inlet and 100 mm outlet |
| 68 | Sand cast iron S&S as per IS: 3989 |
| 69 | Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc.: DSR 18.10 |
| 70 | 15 mm dia. nominal bore |
| 71 | 20 mm dia. nominal bore |
| 72 | 32 mm dia nominal bore |
| 73 | Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc |
| 74 | 32 mm dia nominal bore |
| 75 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : DSR 18.18 |
| 76 | 20 mm dia. nominal bore |
| 77 | Providing and fixing uplasticised PVC connection pipe with brass unions |
| 78 | 30 cm length |
| 79 | 15 mm nominal bore |
| 80 | Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) |
| 81 | 15 mm nominal bore |
| 82 | 20 mm nominal bore |
| 83 | 32 mm nominal bore |
| 84 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank |
| 85 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : |
| 86 | 15 mm nominal bore |
| 87 | Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. |
| 88 | 15 mm nominal bore |
| 89 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 |
| 90 | 15 mm nominal bore |
| 91 | Providing and fixing of Extension nippple upto 1-1/2\\" length |
| 92 | Cutting holes up to 30x30 cm in walls including making good the same: |
| 93 | With common burnt clay F.P.S. (non modular) bricks |
| 94 | Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete so as to make it leak proof. |
| 95 | Making chases up to 7.5x7.5 cm in walls including making good and finishing with matching surface after housing G.I. pipe etc. |
| 96 | Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than .70 kg as per standard design: |
| 97 | 100 x 100 mm size P-type |
| 98 | With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 99 | Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 fine sand : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design: |
| 100 | Inside dimensions 455x610 mm and 45 cm deep for single pipe line |
| 101 | With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 102 | Inside dimensions 500x700 mm and 45 cm deep for pipe line with one or two inlets : |
| 103 | With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 104 | Providing and fixing drip seal joints to sand cast iron/centrifugally cast (spun) iron pipes and fittings of diameter : |
| 105 | 100 MM |
| 106 | Construction of Curb consisting of cement concrete 1:2:4 including cost of C.P. hinged grating and cost of sand bajri etc. |
| 107 | Providing and fixing of CP Brass/SS Towel Rail 600mm of with screws etc. to the satsifaction of EIC of approved make Jal Model No. 36520 Warna or equialent Model of CERA /Kerovit/ ESSCO |
| 108 | Providing and fixing of CP Brass/SS/ABS Soap Tray made of Plastic including glass bowl of approved make Jal Model No. 36540 or equialent Model of CERA /Kerovit/ ESSCO |
| 109 | Providing and fixing of CP Brass/SS Towel Ring with screws etc. to the satsifaction of EIC of approved make Jal Model No. 36524 Warna or equialent Model of CERA /Kerovit/ ESSCO |
| 110 | Providing and fixing ISI marked water proof flush door shutters of pine frame sesoned and treated with seasoned pine filler and 2.5 mm gurjan core, fungus resistant, eco frindly with 1mm thick laminated on bot side with phenol formaldehyde resin conforming to IS:848: complete in all respect. (As per Door frame detail sheet) |
| 111 | Providing and fixing of Wash basin pedestal with C.I. brackets without pillar taps, 32mm CP brass waste of standard pattren ,including painting of fittings and brackets cutting and making good the walls whereever require complete in all respect make as approved by EIC. (Size 550x400mm). |
| 112 | Providing and fixing of pressmatic Pillar Tap complete make Jaquar model PRS-031 or equal vent in the same price range of AOR |
| 113 | Providing and Fixing of Geyser storage capacity 25 Ltr power supply 230v 50Hz Single Phase Wall mounted Complete in all respect of approved make:- Jaquar/Racold/Havells |
| 114 | Providing and Fixing of Geyser storage capacity 50 Ltr porwer supply 230v 50Hz Single Phase Wall mounted Complete in all respect of approved make:- Jaquar/Racold/Havells |
| 115 | Conversion for OWC to EWC with 4\\" C.I. bend, 4\\" PVC collar 1 No 4\\" PVC pipe upto 1'-6\\" long including dismantling of OWC pan and floor and repair of flooring to its original condition complete in all respect with satisfaction of EIC. |
| 116 | Providing and Fixing of tank Nipple for making connection complete in all respect |
| 117 | 20 mm Dia. |
| 118 | 32 mm Dia |
| 119 | Providing and fixing of MS Jali Enclosure made of MS angle 40x40x5mm and 35mm x 35mm x 10 guage wire mesh and MS flat including cutting, welding,fixing and placing at site as per site requirement. |
| 120 | Providing and fixing of Monoblock Pump for boosting arrargement One HP with complete fitting. of Appproved Make |
| 121 | Providing and fixing of MS Cover for Monoblock pump Safty form rain |
| 122 | Supplying and fixing in position pre-cast RCC/SFRC Cover with frame of quality MD-10 and size 450mm |
| 123 | Providing and fixing of Multicore flexible cable PVC Insulated and Sheathed with Bare Copper Conductor as per IS 694 marked complete including making connection to the satisfaction of EIC Make : Havells, Polycab, Finolex or as per approved make list |
| 124 | 2.5 mm² x 3 Core Please Enable Macros to View BoQ information |
