|
| 1 | Taking down chowkhats with shutters (without taking off shutters from the frames) & removing from site area n.exc 1.5 Sqm each complete all as directed. |
| 2 | Taking down chowkhats with shutters (without taking off shutters from the frames) & removing from site area exc 1.5 Sqm & n. exc 4.00 sqm each complete all as directed. |
| 3 | Taking down Shutters of any description not exceeding 1.0 sqm for each leaf all as specified. |
| 4 | Taking down Shutters of any description exceeding 1.0 sqm but not exceeding 2.0 sqm for each leaf all as specified. |
| 5 | Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified. |
| 6 | Dismantling of plain or corrugated steel sheeting, any gauge, thickness including Nainital or similar pattern roof covering complete all as directed. |
| 7 | Dismantling fibre glass reinforced translucent corrugated sheeting of any thickness in roof covering complete all as directed by Engineer-In-Charge. |
| 8 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as directed by Engineer-In-Charge. |
| 9 | Dismantling boarding, any description, fixed in any position with nails complete all as directed. |
| 10 | Dismantling timber scantlings 40 sqcm and over in section for unframed work, in any position all as directed. |
| 11 | Dismantling fillets, rails, posts, rafters, purlins, etc. under 40 sqcm in section for unframed work complete all as directed. |
| 12 | Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets all as directed. |
| 13 | Demolition of cement Concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as directed. |
| 14 | Demolition of cement concrete of any description and in any position complete all as specified. |
| 15 | Demolition of cement Concrete (reinforced) other than ground floors and pavings complete all as directed. |
| 16 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises all as directed by Engr- In- Charge. |
| 17 | Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. complete all as specified. |
| 18 | Demolition of Precast concrete block/ Brickwork or stone/boulder masonry, laid with cement morter complete all as directed. |
| 19 | Taking up or down steel tubing and connections, including cleaning for re-fixing or removal to store 15 mm dia |
| 20 | Taking up or down steel tubing and connections, including cleaning for re-fixing or removal to store 20 mm dia |
| 21 | Supply and fix pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and directed. |
| 22 | Supply and fix pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and directed. |
| 23 | Supply and fix 2mm thick fibre glass reinforced translucent corrugated sheeting with two corrugations side lap fixed with L-type or J-type or cranked hook bolts in lieu of screw using profiled GI washer and bitumen washer in roof covering complete all as specifed and directed. |
| 24 | Supply and fix as in repairs 2 mm thick polycarbonate solid embossed sheet fixing with self tapping screws complete all as per manufacturer instruction. |
| 25 | Supply and fix steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161- 1979 grade St.-240 complete all as specified. |
| 26 | Supply and fix Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing conforming to Fe-410W Grade E-250 (quality A) complete all as specified. |
| 27 | Supply and fix as in repairs Fe-410-W(GdeE-250) qualityA Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment complete all as specified. |
| 28 | Supply and fix mild steel sheet eaves gutters, 1.5 mm thick 150 mm dia, galvanised class 3, half round with rounded edges complete all as specified. |
| 29 | Supply and fix Safety lever locks mild steel with 4 levers for rolling shutters complete all as specified. |
| 30 | Supply and fix Ball bearing for rolling shutters complete all as specified. |
| 31 | Material and labour for second class hardwood weather boarding, clean sawn, plain, 20mm thick or feather edged 15 mm to 20mm thick and fixed with 30mm laps complete all as specified. |
| 32 | Supply and fix 30 mm thick second class hardwood planed one side, with butt joints and fixed with nails supplied and fixed complete all as specified. |
| 33 | Supply and fix 10mm thick wooden laminated flooring floating glue less click locked (HDF based tongue and groove ) and sealed in a manner similar to a jigsaw puzzle on concrete slab/base/on hard wood flooring or vertically and other flat hard surface including 10mm thick under layer of EPE foam sheet of best quality complete all as specified and directed. |
| 34 | Material and labour for second class hardwood scantling wrought sawn complete all as specified. |
| 35 | Supply and fix 2nd class hardwood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified. |
| 36 | Supply and fix rolled mild steel section as in joist, channel, angle, or tee sections,fixed independently, withoutconnecting plates, etc. (cut to ordinary lengths i.e. within 20 mm of the length indicated) conorming to Fe 410 -W (Gde- E- 250) quality-A complete all as specified. |
| 37 | Supply and fix 35 mm thick Plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers fitted to chowkats complete all as specified. |
| 38 | Supply and fix 35 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified. |
| 39 | Supply and fix of 35 mm thick 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc. divided into squares, with out sash bars, edges of framing plain, chamfered or rounded, fitted with cut and mitered beads for securing glass etc. and size of the members of shutter is as specified in clause No. 8.24 (a) of MES schedule 2009, part – I (Specifications). |
| 40 | Supply and fix of 30 mm thick 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc. divided into squares, with out sash bars, edges of framing plain, chamfered or rounded, fitted with cut and mitered beads for securing glass etc. and size of the members of shutter of windows, ventilators, etc. are provided with stiles and rails as specified in SSR Part I, Section 8 clause 8.24(b). |
| 41 | Supply and fix 30 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified. |
| 42 | Supply and fix in repairs Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified. |
| 43 | Supply and fix PVC door frame of size 50 mm X 47 mm made out of 5 mm thick plain colour PVC sheet reinforced with MS square tube complete all as specified. |
| 44 | Supply and fix 30 mm thick factroy made solid panel PVC door shutter (style) consisting of frame made out of MS tube for top and bottom rails MS frame shall be covered with neat moulded plain colour PVC channel having a PVC sheet strip of 20mm width stuct inside the solvent cement for style and single side pre laminated PVC sheet for top rails, lock rails and bottom rails on either side and as gap insert for top rails and bottom rail panelling of plain colour PVC sheet to be fitted in the MS frame welded to the style and rails with suitable PVC sheet beading and jointed together with solvent cement supplying and fixing in the frame at site as per specification . |
| 45 | Supply and fix 0.63 mm thick plain, galvanised, mild steel sheeting in stepped flashings (measured as the minimum rectangle from which the pieces can be cut) complete all as specified. |
| 46 | Supply and fix bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified. |
| 47 | Supply and fix powder coated anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified |
| 48 | Supply and fix anodised aluminium door shutters with powder coating of any colour (Thickness or powder coating not less than 50 micron), aluminium section weighing not less than 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, 4 lever mortice lock, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified |
| 49 | Supply and fix Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge. |
| 50 | Supply and fix WPC door frame of size 50 mm X 47 mm single revit (black 5 x 2.5) complete all as per manufacturer instruction |
| 51 | Supply and fix factory made solid panel WPC shutter 35 mm thick complete all as per manufacturer instruction. |
| 52 | Cutting chases, pinning in brick walls making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified. |
| 53 | Supply and fix 3 mm thick sheet glass, ordinary quality and glazing in square exceeding 0.50 sqm in each pane in aluminium joinery in each pane complete all as specified. |
| 54 | Supply and fix 4 mm thick figured glass, pin head type and glazing in square exceeding 0.50 sqm in each pane in aluminium joinery in each pane complete all as specified. |
| 55 | Supply and fix 5.5 mm thick sheet glass, ordinary quality and glazing in square exceeding 0.50 sqm in each pane in aluminium joinery in each pane complete all as specified. |
| 56 | Supply and fix galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks, or galvanised wire staples complete all as specified. |
| 57 | Supply and fix as in repairs galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks, or galvanised wire staples complete all as specified. |
| 58 | Supply and fix as in repairs aluminium (die cast body) Door closer hydraulically regulated, designation No. 2, universal type, suitable for door shutters of 851 mm to 1000 mm in width and of weight between 61 kg to 80 kg and fixed complete all as specified. |
| 59 | Supply and fix 100 mm long medium weight, cold rolled mild steel, Butt hinges, complete all as specified. |
| 60 | Supply and fix 75 mm long medium weight, cold rolled mild steel, Butt hinges, complete all as specified. |
| 61 | Supply and fix 100 mm long aluminium alloy handles, fabricated type, anodized all as specified. |
| 62 | Supply and fix 150 mm long aluminium alloy handles, fabricated type, anodized all as specified. |
| 63 | Supply and fix 100 mm long aluminium anodised barrel tower bolts of extruded section all as specified. |
| 64 | Supply and fix 200 mm long aluminium anodised barrel tower bolts of extruded section all as specified. |
| 65 | Supply and fix 300 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified. |
| 66 | Supply and fix as in repairs 18/19 mm thick prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified. |
| 67 | Supply and fix as in repairs 12 mm thick plywood, grade BWR, type BB, fixed with screws to timber frame work complete all as specified. |
| 68 | Material and labour 2nd class hardwood Plain fillets. square,rectangular or triangular in section, clean sawn, secured with nails or brads not exceeding 3 sqcm complete all as specified. |
| 69 | Supply and fix as in repairs 40 mm width of flap (when open) continuous (piano) hinges, mild steel, bright finish or electro galvanised complete all as specified. |
| 70 | Supply and fix as in repairs 4 lever Mortice lock, vertical type, size 100 mm (set of 2 keys) complete all as specified. |
| 71 | Supply and fix as in repairs 100 mm long hasp and staple, of aluminium anodised including bolt to hinge plate and fixed with screws complete all as specified. |
| 72 | Supply and fix as in repairs magnetic catches for wardrobe, almirah complete all as specified. |
| 73 | Supply and fix floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor overall size of cover plate 140 mm complete all as specified. |
| 74 | Supply and fix as in repairs floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor overall size of cover plate 140 mm complete all as specified. |
| 75 | Supply and fix stainless steel wall cloth hooks set of 6 prongs suitable for bathroom, kitchen etc complete all as directed by Engineer-In-Charge. |
| 76 | Supply and fix 5 mm thick PVC sheet fillet of width 35 mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing. complete all as directed by Engineer-In-Charge. |
| 77 | Supply and fix door bottom seal 90 cm-100 cms in length 42 mm wide including aluminium plate (22mmx6.16mm thk) with nylon brush (20 mm wide) fixed with tapping screw as per manufacturer instruction. |
| 78 | Material and labour for for suspended false ceiling using grid 180 GSM (exposed ceiling suspension system ) of grid size 605 mm x 605 mm with main runner 38 mm x 24 mm and wall angle 24 mm x 24 mm using 4 mm thick High Pressure steel Non Asbestos Fibre Cement decorative Board in a grid of powder coated GI system duly suspended with 4 mm dia GI bar hanger fixed with steel dash fasteners or iron purlin from the roof with adjustment clip providing positions for light fixtures, air conditioning diffuser and ducts ,sprinkler ,smoke detectors etc. The main runners to be secured to structural soffits by hanger @ 1210 mm maximum c/c. the last hanger at the end of each main runner should not be placed at more than 450 mm from the adjacent wall, Flush fitting 1210 mm cross tee to be interlocked between main runners @ 605 mm c/c,so as to form 600 mm x 600 mm grid complete all as specified . Make: Everest/ Lafarge/ Armstrong |
| 79 | Supply and fix 4 mm thick non asbestos fibre cement building boards fixed or laid/ inserted to timber/GI/Alumi nium framework with screws complete all as specified. |
| 80 | Demolition of existing roof padding including roof treatment complete carefully by cutting, chiselling etc cleaning the surfaces by scrapping, booming brushing etc and removing the rubbish from site to a distance exc 50m and n.exc 100m all as directed by the Engineer-in-Charge and M&L for applying roof treatment as under :-(i) Providing 10mm thick (average) rendering in cement mortar 1:3 mixed with WPC as per manufacture's instruction (to be measured and paid including this item) for levelling to a true surface and to receive new roof treatment complete.(ii) Providing coat of bitumen primer @ 0.40 Kg/Sqm complete .(iii) Providing coat of hot blown bitumen of grade 85/25 @ 1.2 Kg/Sqm over primer surfaces alongwith aluminium paint @ 0.11 Kg/Sqm over the APP.(iv) Providing a layer of APP based polymeric membrance of approved manufacturer, 3mm thick reinforced with polyester non wooven fabrix (weighing not less than 150 gm/ Sqm) laid by torch application method, side overlaps shall be minimum 75mm and end laps shall be minimum 100mm and sealing all overlaps and joints as manufacturer's insructions and provided upto a height o 60cm in the parapets and inserted inside the parapets by cutting a groove and finished by membrane flashing complete all as directed. |
| 81 | Material and labour for 7 mm thick joint free premium quality glazed ceramic colour tiles of size 450 mm x 300 mm/ 600 mm x 300 mm as in skirting / dado / vertical surfaces set and jointed and pointed in white or colour cement to match existing surfaces including 10 mm thick rendering in cement mortar 1:3 complete all as specified. |
| 82 | Material and labour for 10 mm thick joint free premium quality light shed vitrified ceramic tiles of size exc. 0.42 Sqm but Not exc. 1.00 Sqm as in floors set and jointed and pointed in white or colour cement to match existing surfaces laid over 20 mm thick screed bed in cement mortar 1:4 complete all as specified. |
| 83 | Material and labour for 10 mm thick joint free premium quality light shed vitrified ceramic tiles of size exc. 0.42 Sqm but Not exc. 1.00 Sqm as in skirting / dado / vertical surfaces set and jointed and pointed in white or colour cement to match existing surfaces including 10 mm thick rendering in cement mortar 1:3 complete all as specified. |
| 84 | Material and labour for 7 to 8 mm thick joint free premium quality anti skid colour ceramic tiles size of each tiles should be 400 mm x 400 mm as in floors set and jointed and pointed in white or colour cement to match existing surfaces including 20 mm thick screed bed in cement mortar 1:4 complete all as specified. |
| 85 | Material and labour for 10 mm thick joint free premium quality light shed vitrified ceramic tiles of size 600 mm x 600 mm as in floors set and jointed and pointed in white or colour cement to match existing surfaces laid over 20 mm thick screed bed in cement mortar 1:4 complete all as specified. |
| 86 | Material and labour for 10 mm thick joint free premium quality light shed vitrified ceramic tiles of size 600 mm x 600 mm as in skirting / dado / vertical surfaces set and jointed and pointed in white or colour cement to match existing surfaces including 10 mm thick rendering in cement mortar 1:3 complete all as specified. |
| 87 | Supply and fix Pavement floor vitrified tiles of size 300x 300x 10 mm thk (Endura tiles of Johnson or equivalent makes listed in List of Makes) of approved colour and design set and jointed in neat cement slurry and pointed in white or coloured to match including 20 mm th screed bed in cement mortar 1:4 complete all as specified and directed. |
| 88 | Supply and fix 10 mm thk Pavement floor vitrified tiles of size exc. 0.09 Sqm but not exc. 0.36 Sqm (Endura tiles of Johnson or equivalent makes listed in List of Makes) of approved colour and design set and jointed in neat cement slurry and pointed in white or coloured to match existing surfaces as in skirting / dado / vertical surfaces including 10 mm thick rendering in cement mortar 1:3 complete all as specified. |
| 89 | Material and labour 25 mm thick PCC type B0, 1:2:4 using 12.50 mm graded crushed stone aggregates as in levelling coarse of floors including finishing the concrete surface even & fair without using extra cement complete all as specified. |
| 90 | Supply and fix 30 mm thick factroy made solid panel PVC door shutter (style) consisting of frame made out of MS tube for top and bottom rails MS frame shall be covered with neat moulded prelaminated colour PVC 'C' channel having a PVC sheet strip of 20mm width stuct inside the solvent cement for style and single side pre laminated PVC sheet for top rails, lock rails and bottom rails on either side and as gap insert for top rails and bottom rail panelling of plain colour PVC sheet to be fitted in the MS frame welded to the style and rails with suitable PVC sheet beading and jointed together with solvent cement supplying and fixing in the frame at site as per specification . |
| 91 | Material and labour for cement concrete type B0, 1:2:4 (12.50mm graded aggregate), rounded or chamfered on edges in lintels upto 1.5 m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, coping kneelers, apex stones, bed plates, kerbs not provided for roof kerbs or mud stops, rounded or chamfered on edges, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, including water proofing compound complete all as specified |
| 92 | Material and labour 50 mm thick PCC type C2, 1:3:6 using 40mm graded crushed stone aggregates as in hard standing/plinth protection including finishing the concrete surface even & smooth without using extra cement and laid in alternate bay complete all as specified. |
| 93 | Material and labour for PCC 1:3:6 type C2 using 40 mm graded crushed stone aggregates as in Foundation, filling and mass concrete complete all as specified. |
| 94 | Material and labour for 18-20 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including 20 mm thick screed bed in cement mortar 1:4, including edge moulding of counters vanities etc. and machine polishing to edge to give high gloss finish etc. including demolition complete all as specified. |
| 95 | Material and labour for reinforced cement concrete 1:1.5:3 type B1 using 20 mm graded crushed stone aggreagates as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified.Note: Formwork shall be measured and paid including this item but reinforcement shall be measured and paid separately. |
| 96 | Material and labour for Mild steel TMT bars of Fe 500D, 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for chainlink fencing and binding with and including mild steel wire (annealed) not less than 0.90 mm dia or securing with clips complete all as specified. |
| 97 | Supply and fixing factory made uPVC white colour Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) upto 1.50m height made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) comprising of uPVC multichambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. (Glass or wiremesh shall be paid separately).Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. |
| 98 | Material and labour for 15 mm thick rendering on fair faces of brick or concrete surfaces in cement mortar 1:6 finshed even and smooth without using extra cement complete all as specified. |
| 99 | Material and labour for 5 mm thick rendering in cement mortar 1:3 on fair faces of ceiling surfaces, finished the surfaces even and smooth without using extra cement complete all as specified. |
| 100 | Material and labour for 15 mm thick rendering in cement mortar 1:4 in two layers (10 mm +5 mm) on external faces of brick wall or concrete surfaces, finished the surfaces even and smooth without using extra cement with using approved LWPC on second layer (5 mm) as per manufacturer instruction complete all as specified and as directed by Engineer-In-Charge. Note: LWPC shall be measured and paid including this item |
| 101 | Material and labour for 10 mm thick rendering on fair faces of brick or concrete surfaces in cement mortar 1:4 finshed even and smooth without using extra cement complete all as specified. |
| 102 | Supply and fix as in repairs Rotational moulded polyethylene water storage overhead tanks (cylindrical vertical with closed top) multi layered 500 ltr capacity hoisted and fixed in position including 20 mm dia Ball valves (Minimum weight of valve 210 gms) high pressure of PTMT with epoxy coated Aluminium rod and high density plastic ball screwed for iron pipe complete all as specified including dismantling the old unserviceable one. |
| 103 | Supply and fix as in repairs Rotational moulded polyethylene water storage overhead tanks (cylindrical vertical with closed top) multi layered 1000 ltr capacity hoisted and fixed in position including 20 mm dia Ball valves (Minimum weight of valve 210 gms) high pressure of PTMT with epoxy coated Aluminium rod and high density plastic ball screwed for iron pipe complete all as specified including dismantling the old unserviceable one. |
| 104 | Supply and fix as in repairs float ball valves 20mm dia high pressure PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed complete all as specified and as directed by Engineer-In-Charge. |
| 105 | Disconnecting existing tanks of Capacity exceeding 250 ltr but not exceeding 500 ltr, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position including cleaning repairing, etc.as directed by Engineer-In-Charge. |
| 106 | Disconnecting existing tanks of Capacity exceeding 500 ltr but not exceeding 1000 ltr, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position including cleaning repairing, etc.as directed by Engineer-In-Charge. |
| 107 | Supply, lay and fix 15 mm bore galvanized iron water tubing medium grade including all fittings and fixed complete to walls and ceiling or laid in floors all as specified. |
| 108 | Supply, lay and fix 20 mm bore galvanized iron water tubing medium grade including all fittings and fixed complete to walls and ceiling or laid in floors all as specified. |
| 109 | Laying Only 15 mm bore galvanized iron water tubing medium grade including all fittings and fixed complete to walls and ceiling or laid in floors all as specified. |
| 110 | Laying only 20 mm bore galvanized iron water tubing medium grade including all fittings and fixed complete to walls and ceiling or laid in floors all as specified. |
| 111 | Supply and fixing factory made uPVC white colour Casement door with 3D hinges made of (big series) frame 67 x 64 mm & sash 67 x 110 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of door upto 2.00 sqm) comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws,etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality complete all as specified and directed by Engineer-in- Charge. (Glass shall be paid separately)Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. |
| 112 | Supply and fix one piece Vitreous China wash down water closet pan floor mounted, white including fixing bolts, 10 ltr capacity flushing cistern,flush pipe plastic water closet seat white including jet spray, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging devices and also including 'P' or 'S' trap including taking out old pedestal alongwith existing all fittings and making the surface match with existing surface complete all as per manufacturer instruction.Make of Pan Parryware Verve AM / Cera CAMPBELL/ Johnshon COSMO |
| 113 | Supply and fix as in repairs soft closing plastic water closet seat cover , white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified. |
| 114 | Supply and fix for aluminium composite panel board, antibacterial fireproof surface coating of thickness 30um (micrometer) thickness 3mm to 4 mm. weight not less than 4.5 kg/ sqm based on 4 mm carbon resin (PVDF) and plyester resin (PE) roasting painting, core nontoxic polyethylene, black aluminium alloy sheet coated with polyster resin painting surface finish treated with PVDF and PE resin rolling roasting, coating aluminium alloy sheet thickness 0.50 mm including anodized brushed mirror PE coated colour, PVDF coated fixing with powder coated ACP shutter framed with 40x20x1.47 mm around to matched colour ACP panels including necessary cleats, rubber neoprene packing, side locking arrangements eic. complete all as per manufacturer instruction. |
| 115 | Material and labour for 0.90 mm decorative laminate type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer's instruction. |
| 116 | Supply and fix as in repair vitreous china wash basin counter top oval type of size 545x400x185mm including 32mm dia waste fitting including brackets and 32mm dia waste fitting with PVC drainage waste pipe required length upto floor trap complete all as specified. |
| 117 | Supply and fix as in repairs, brass CP single lever basin mixer swan neck pattern for mixing hot and cold water including 15 mm bore hot water pipe duly insulated with glass wool and aluminium cladding complete all as specified. |
| 118 | Material and labour for brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in cement mortar 1:4 complete all as specified. |
| 119 | Supply and fix as in in repairs 32 mm dia waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified.Note: Make shall be provided as per existing one. |
| 120 | Supply and fix as in repairs 32 mm bore bottle trap of PTMT having minimum water seal of 25mm of Minimum weight 260gms complete all as specified.Make: Prayag Polymer Pvt Ltd/ Polytuff/ Cera/ Shakti |
| 121 | Supply and fix as in repairs sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and waste coupling and waste pipe; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915mm x 460 mm bowl size 410mm x 330mm x 160mm complete all as specified. |
| 122 | Supply and fix as in repairs sinks without drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and waste coupling and waste pipe; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified. |
| 123 | Supply and fix as in in repairs 40 mm dia waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified.Note: Make shall be provided as per existing one. |
| 124 | Supply and fix as in repairs PVC flexible sink/wash basin waste pipe drain hose/ outlet pipe of 35 inches as spesified and directedNote: Make shall be provided as per existing one. |
| 125 | Supply and fix in repair chromium plated Sink mixer for mixing hot & cold water, wall mounted swan neck pattern screwed down for iron pipe and fixed complete all as per manufacturer instruction.Make:- Parryware Cat No G0639A1/ Jaquar Cat No COP-309PM/ Johnson Cat No T3220C |
| 126 | Supply and fix as in repairs for 15 mm bore Chromium plated fancy type long neck Bip taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as directed. Make:- Parryware Cat No G1806A1/ Jaquar Cat No CON-107KN/ Johnson Cat No T6006C |
| 127 | Supply and fix as in repairs 15 mm dia cast copper alloy chromium plated Angle valves, with wall flange concealed type screwed down for iron pipe of for unions complete all as specified and directed. Make :- Parryware Cat No T3907A1/ Cera Cat No F1016201/ Johnson Cat No T5310C |
| 128 | Material and labour in repair for 15 mm dia brass CP two way Angle valve with wall flange concealed type screwed down for iron pipe or for unions complete all as per manufacturer instruction.Make :- Parryware Cat No G0643A1/ Cera Cat No F2002211/ Johnson Cat No T5512C |
| 129 | Supply and fix as in repairs for 15 mm dia cast copper alloy chromium plated two way Bib cock with wall flange concealed type screwed down for iron pipe or for unions complete all as Per manufacturer instruction.Make :- Parryware Cat No G2381A1/ Cera Cat No F1016163/ Johnson Cat No T3370C |
| 130 | Supply and fix as in repairs CP health faucet with tube and wall hook including all fittings as per manufacturer instruction.Make: Parryware Cat No T9961A1/ Jaquar Cat No ALD-579 / Johnson Cat No S0826C |
| 131 | Supply and fix as in repairs for 15 mm bore dia of pipe Brass CP Wall mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as per manufacturer instruction.Make:- Parryware Cat No G3317A1/ Jaquar Cat No CQT-23281UPR/ Johnson Cat No T6023C |
| 132 | Supply and fix as in repairs brass CP shower rose with or without swivel joints, 125 mm size, including fixing to steel pipe or union complete all as specified.Make:- Jaquar / Parryware / Marc/ Cera/ Johnson |
| 133 | Supply and fix as in repairs Hand Shower with 8 mm dia and 1.00 mtr long flexible tube and wall hook complete all as directed. Make:- Jaquar / Parryware / Marc/ Cera/ Johnson |
| 134 | Supply and fix as in repairs 20 mm dia chromium plated tubular towel rail and 600 mm long with brackets, complete all as specified.Make:-Jaquar Cat No ACN-1111SM/ Parryware Cat No T6001A1/ Cera Cat No F5007103 |
| 135 | Supply and fix as in repairs 20 mm dia chromium plated tubular towel rack and 600 mm long with brackets, complete all as specified.Make:-Jaquar Cat No ACN-1181S/ Parryware Cat No T6008A1/ Cera Cat No F5003101 |
| 136 | Supply and fix as in repairs Sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified.Make: Prayag Polymer Pvt. Ltd./ Saint Gobain/ Modiguard/ Jaquar & Company Private Limited./ Cera |
| 137 | Supply and fix as in repairs corner glass shelf of size 300 mm radius (with brass chromium plated brackets) fixed in wall with necessary screws etc. complete all as per directed by Engineer-In-Charge.Make: Prayag/ Parryware/ Commander/ Polytuff |
| 138 | Supply and fix as in repairs PVC toilet mirror cabinet with mirror of overall size 330 mm x 430 mm and fixed to wall complete all as per directed by Engineer-In-Charge.Make: Prayag/ Parryware/ Commander/ Polytuff |
| 139 | Supply and fix as in repair Looking mirror of selected quality glass size 100 cm x 60 cm with 40 mm wide hardwood beading all around and fixed to wooden plugs with chromium plated screws complete all as directed.Make: Jaquar & Company Private Limited. / Cera/ Saint Gobain/ Modiguard/ Prayag Polymer Pvt. Ltd. |
| 140 | Supply and fix as in repairs 600 mm x 450 mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified.Make: Jaquar & Company Private Limited. / Cera/ Saint Gobain/ Modiguard/ Prayag Polymer Pvt. Ltd. |
| 141 | Supply and fix as in repairs toilet paper holder as per manufacturer instruction.Make:- Jaquar Cat No AKP-35755PS/ Parryware Cat No T6005A1/ Cera Cat No F5006109 |
| 142 | Supply and fix as in repairs soap dish, fancy type, fixed to plugs with chromium plated brass screws complete all as specified.Make:- Kohler/ Jaquar/ Cera/ Hindware |
| 143 | Supply and fix as in repairs PVC connections 15 mm size with PTMT nuts of length 450 mm,complete all as specified.Make:-Blue Star & Silver Shine/ Prayag Polymer Pvt. Ltd./ Polytuff |
| 144 | Supply and fix as in repairs 450 mm long CP brass connection pipe with CP brass nuts on both ends for fixing to pipe or other fittings complete all as per existing make. |
| 145 | Supply and fix as in repairs, stainless steel kitchen plate rack of size 31 x 30 x 10 inch made out of 1 mm thick stainless steel sheet complete all as per manufacturer instruction.Make: Prayag/ Nirali/ Blue Star & Silver Shine |
| 146 | Supply and fix as in repairs Gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as directed for 20 mm bore all as specified.Make: Audco(L&T)/ Zoloto/ Kirloskar/ Leader/ Upadhyaya |
| 147 | Supply and fix as in repairs 75mm dia PVC (SWR) floor trap, plain with gratings including jointing with solvent cement complete all as specified and directed.Make: Jain Irrigation/ Kisan/ Supreme/ Prince/ Reliance/ Oriplast Please Enable Macros to View BoQ information |
| 148 | Supply and fix as in repairs 75mm dia PVC (SWR) floor trap, plain with gratings including jointing with solvent cement complete all as specified and directed.Make: Jain Irrigation/ Kisan/ Supreme/ Prince/ Reliance/ Oriplast Please Enable Macros to View BoQ information |
